Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively invest...Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively investigated.Macroscopic morphology,microstructure,and interfacial structure of the joints were analyzed using scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer(XRD).The results show that magnetic pulse welding of dissimilar Mg/Fe metals is achieved using an Al interlayer,which acts as a bridge for deformation and diffusion.Specifically,the AZ31B/AA1060 interface exhibits a typical wavy morphology,and a transition zone exists at the joint interface,which may result in an extremely complex microstructure.The microstructure of this transition zone differs from that of AZ31B magnesium and 1060 Al alloys,and it is identified as brittle intermetallic compounds(IMCs)Al_(3)Mg_(2) and Al_(12)Mg_(17).The transition zone is mainly distributed on the Al side,with the maximum thickness of Al-side transition layer reaching approximately 13.53μm.Incomplete melting layers with varying thicknesses are observed at the primary weld interface,while micron-sized hole defects appear in the transition zone of the secondary weld interface.The AA1060/DC56D interface is mainly straight,with only a small number of discontinuous transition zones distributed intermittently along the interface.These transition zones are characterized by the presence of the brittle IMC FeAl_(3),with a maximum thickness of about 4μm.展开更多
Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic ...Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic rolled SF-7055 Al alloy is elongated to form a fiber texture.Numerous proliferating dislocations in the microstructure accumulate into dislocation walls and cells,and eventually form subgrains.These subgrain boundaries divide the original grain,thereby reducing the grain size.Under severe deformation conditions,they even enable the formation of nanograins.Meanwhile,the Cu-rich precipitates in the matrix are also broken and refined under the action of large rolling stress.In the process of cryogenic rolling,the tensile strength and hardness of SF-7055 Al alloy gradually increase,while the plasticity decreases.Moreover,the fracture morphology of cryogenic rolled SF-7055 Al alloy gradually transforms to the ductile and quasi-cleavage hybrid fracture characteristics with increased reduction.展开更多
The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepar...The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepared by vacuum arc melting.The microstructure,mechanical properties,and related influencing mechanisms were systematically investigated.The results indicate that the solidification microstructure of the Ti46Al1.5Cr8Nb-xTa alloys comprises theγ-TiAl phase,α_(2)-Ti_(3)Al phase,and B2 phase.As the Ta content increases from 0.2 at.%to 1.0 at.%,the content ofα_(2)phase and B2 phase increases,while theγphase content decreases.Among them,the B2 phase shows the most pronounced change,being significantly refined,with its content increasing from 12.49%to 21.91%.In addition,the average size of the lamellar colony decreases from 160.65 to 94.44μm.The addition of the Ta element shifts the solidification path toward lower aluminum concentrations,leading to changes in phase content.The tantalum-induced increase in the B2 phase and enhanced supercooling at the solidification front provide the basis for lamellar colony refinement.Compressive testing at room temperature reveals that the Ti46 Al1.5 Cr8 Nb0.4 Ta alloy exhibits optimal compressive properties,achieving a compressive strength of 2,434 MPa and a compressive strain of 33.1%.The improvement of its properties is attributed to a combination of lamellar colony refinement,solid solution strengthening resulting from the incorporation of Ta element,and a reduction in the c/a of theγphase.展开更多
The age-hardening response,mechanical,and corrosion-resistant properties of AA7085 alloys with and without the addition of 0.3 wt.%scandium(Sc)were compared.Using advanced techniques such as aberration-corrected trans...The age-hardening response,mechanical,and corrosion-resistant properties of AA7085 alloys with and without the addition of 0.3 wt.%scandium(Sc)were compared.Using advanced techniques such as aberration-corrected transmission electron microscopy and first-principles calculations,the underlying micromechanisms of Sc microalloying were revealed.Results show that the increase in strength of the AA7085-Sc alloy is mainly attributed to the decreased Al grain size and increased number density of both Al_(3)Sc@Al_(3)(Sc,Zr)core−shell nanoparticles and Sc-containingη_(p) and GP−η_(p) nanoprecipitates.Strong strain fields and evident electron transfer from Zr to the neighboring matrix Al atoms exist at the Al_(3)Sc@Al_(3)(Sc,Zr)/Al interface.The Sc doping in GP−η_(p) andη_(p) suppresses the GP−η_(p)→η_(p) transformation.Modified corrosion resistance of the AA7085-Sc alloy compared with AA7085 alloy is associated with the fine grain boundary precipitates ofη_(p)hases and narrow precipitation free zone.The reasons of property changes of AA7085 alloy after Sc microalloying are explored based on the multiscale microstructural characterization.展开更多
The commercial AM60(Mg−6Al−0.3Mn)die-casting alloy was modified through Mn,Ce,and La micro-alloying,each at a content below 0.2 wt.%.SEM,TEM,and Micro-CT were employed to characterize the microstructures and propertie...The commercial AM60(Mg−6Al−0.3Mn)die-casting alloy was modified through Mn,Ce,and La micro-alloying,each at a content below 0.2 wt.%.SEM,TEM,and Micro-CT were employed to characterize the microstructures and properties of AM60 based alloys.AM60-0.2La alloy showed excellent mechanical properties.The ultimate tensile strength,yield strength,and elongation of(288.0±1.7)MPa,(158.0±1.0)MPa,and(22.0±3.0)%were achieved in AM60-0.2La alloy.Besides,AM60-0.2La alloy exhibited the best corrosion resistance(0.29 mm/a)and fluidity among the investigated four alloys.The excellent mechanical properties and corrosion resistance are mainly attributed to the grain refinement strengthening,low porosity,and low content of large shrinkage porosity,promising for super-sized integrated automotive components.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of re...Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of recycled coral aggregate on concrete properties,this study performed a comprehensive analysis of the physical properties of recycled coral aggregate and the basic mechanical properties and microstructure of RCAC.The test results indicate that,compared to coral debris,the crushing index of recycled coral aggregate was reduced by 9.4%,while porosity decreased by 33.5%.Furthermore,RCAC retained the early strength characteristics of coral concrete,with compressive strength and flexural strength exhibiting a notable increase as the water-cement ratio decreased.Under identical conditions,the compressive strength and flexural strength of RCAC were 12.7% and 2.5% higher than coral concrete's,respectively,with porosity correspondingly reduced from 3.13% to 5.11%.This enhancement could be attributed to the new mortar filling the recycled coral aggregate.Scanning electron microscopy(SEM)analysis revealed three distinct interface transition zones within RCAC,with the‘new mortar-old mortar’interface identified as the weakest.The above findings provided a reference for the sustainable use of coral concrete in constructing offshore islands.展开更多
The Cu-12Fe alloy has attracted significant attention due to its excellent electrical conductivity and electromagnetic shielding capability,high strength,cost-effectiveness,and recyclability.In the present work,the Cu...The Cu-12Fe alloy has attracted significant attention due to its excellent electrical conductivity and electromagnetic shielding capability,high strength,cost-effectiveness,and recyclability.In the present work,the Cu-12Fe alloy strip with the thickness of 2.4 mm was successfully produced by twin-roll strip casting.The microstructure and properties of the Cu-12Fe alloy were tailored by cold rolling and aging treatment.The tensile strength of the as-cast strip is approximately 328 MPa and its elongation is 25%.The Fe phase randomly dispersed in the matrix,and the average size of Fe-rich phase is 2μm.Besides,enrichment of Fe phase is observed in the central layer of the strip,results in the formation of the“sandwich structure”.Moreover,the as-cast strip of Cu-12Fe was directly cold-rolled from 2.4 to 0.12 mm.The directly cold-rolled sample after aging at 450℃for 16 h(ProcessⅠ)shows excellent electrical conductivity of 69.5%IACS,the tensile strength and elongation are 513 MPa and 3.8%,the saturation magnetic flux density is 20.1 emu·g^(-1),and the coercive force is 25.2 Oe.In ProcessⅡ,the as-cast strip firstly cold-rolled to 1.2 mm,then aged at 500℃for 1.5 h,followed by cold rolling to 0.12 mm,finally aged at 450℃for 16 h.The sample after ProcessⅡshows the electrical conductivity of 66.3%IACS,the tensile strength of 533 MPa,an elongation of 3.5%,saturation magnetic flux density of 21.4 emu·g^(-1),and the coercive force of 22.3 Oe.展开更多
To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrough...To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrought Zn−0.1Mg alloy by annealing at 200℃ for varying durations.The findings reveal that the tensile strength of the alloy rapidly and significantly declines with prolonged annealing time,decreasing from 383 MPa for the as-received alloy to 102 MPa for the alloy subjected to 1440 min of annealing.The primary factors contributing to this considerable reduction in strength are static recrystallization,grain coarsening,and dislocation annihilation.Initially,the ductility of the alloy shows fluctuations,ultimately experiencing a marked decrease after extended annealing.This decline is linked to the grain growth and heightened texture intensity,while the unusual increase in ductility observed between 30 and 120 min of annealing is likely due to the formation of twins.In addition,due to rapid grain growth and an increase in precipitates and twins,the corrosion resistance of the alloy in Hank’s solution has worsened,with the corrosion rate rising from 0.037 to 0.069 mm/a following 300 min of annealing.展开更多
Zn's natural degradability and biocompatibility make it a promising candidate for implants,however,its mechanical properties remain insufficient for bone applications.In this study,the performance of Zn was enhanc...Zn's natural degradability and biocompatibility make it a promising candidate for implants,however,its mechanical properties remain insufficient for bone applications.In this study,the performance of Zn was enhanced by developing Zn-Cu alloys via laser powder bed fusion(LPBF).Optimal LPBF parameters for forming stable tracks were achieved by adjusting laser power and scanning speed.Under optimized conditions of 100 W and 100 mm/s,high density(99.58%)Zn-Cu alloys with improved hardness(68.2 HV)and yield strength(160 MPa)were achieved.These improvements are attributed to solid solution strengthening,segregation strengthening,and grain refinement.The Zn-Cu alloys also demonstrated favorable degradation behavior,with a rate of 0.16 mm/year.This degradation is primarily driven by micro-galvanic corrosion between the CuZn 5 phase and Zn matrix,along with refined grains and increased grain boundary density.This work demonstrates a viable strategy for fabricating Zn-based implants with enhanced structural integrity and mechanical performance via LPBF.展开更多
High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as not...High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as notable solid-state welding and processing techniques,have been proved effectiveness in enhancing microstructures and mechanical properties of HEAs.This review article summarizes the current status of FSW/P of HEAs.The welding materials and conditions used for FSW/P in HEAs are reviewed and discussed.The effects of FSW/P on the evolutions of grain structure,texture,dislocation,and secondary phase for different HEAs are highlighted.Furthermore,the influences of FSW/P on the mechanical properties of various HEAs are analyzed.Finally,potential applications,challenges,and future directions of FSW/P in HEAs are forecasted.Overall,FSW/P enable to refine grains of HEAs through dynamic recrystallization and to activate diverse deformation mechanisms of HEAs through tailoring phase structures,thereby significantly improving the strength,hardness,and ductility of both single-and dual-phase HEAs.Future progress in this field will rely on comprehensive optimization of processing parameters and alloy composition,integration of multi-scale modeling with advanced characterization for in-depth exploration of microstructural mechanisms,systematic evaluation of functional properties,and effective bridging of the gap between laboratory research and industrial application.The review aims to provide an overview of recent advancements in the FSW/P of HEAs and encourage further research in this area.展开更多
The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solutio...The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.展开更多
The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding ...The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding 0.2 wt.%Mn to T6-treated Al−Si−Mg alloys enhanced the corrosion resistance by promoting the formation ofα-AlFeMnSi phase,characterized by smaller absolute Volta potential values compared to eutectic Si,β-AlFeSi andπ-AlFeMgSi phases.However,the addition of 0.5 wt.%Mn and 1.0 wt.%Mn to the T6-treated Al−Si−Mg alloys increased the size of theα-AlFeMnSi phase.This decreased the properties of T6-treated Al−Si−Mg alloys.Therefore,the optimum Mn content was 0.2 wt.%,providing a novel approach for synergistically enhancing mechanical properties and corrosion resistance of Al−Si−Mg alloys.展开更多
In current research,Li_(2)O-Al_(2)O_(3)-SiO_(2)glass-ceramics were prepared by conventional meltquenching and subsequent heat treatment method.The effect of Al_(2)O_(3)content on microstructures,thermal properties,cry...In current research,Li_(2)O-Al_(2)O_(3)-SiO_(2)glass-ceramics were prepared by conventional meltquenching and subsequent heat treatment method.The effect of Al_(2)O_(3)content on microstructures,thermal properties,crystallization behaviours and mechanical properties were investigated.FTIR,Raman spectroscopy and nuclear magnetic resonance spectroscopy microstructure analysis showed that the silico-oxygen network was damaged,while the increase of[AlO_(4)]content repaired the glass network,and finally made the glass network have better connectivity,with the decrease of SiO_(2).The thermal analysis confirmed the increasing glass transition and crystallization temperatures from growing Al_(2)O_(3)content.In addition,different crystal phases can be precipitated in the glass matrix,such as LiAlSi_(4)O_(10),Li_(2)Si_(2)O_(5) in glass with low Al_(2)O_(3)content,the combination of Li_xAl_xSi_(1-x)O_(2),LiAlSi_(3)O_(8),Li_(2)SiO_(3)in glass with intermediate Al_(2)O_(3)content,and the combination of LiAlSi_(2)O_(6),SiO_(2)in glass with high Al_(2)O_(3)content.The hardness of as-prepared glass gradually increases with the increase of the Al_(2)O_(3)content.The Vickers hardness of the glass-ceramics is highly dependent on the Al_(2)O_(3)content in the glass and the heat treatment temperatures,reaching a maximum of 10.11 GPa.Scanning electron microscope images show that the crystals change from spherical to massive and finally to sheet.The change of glass structure,crystal phase and morphology is the main reason for the different mechanical properties.展开更多
Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the eff...Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the effects of strengthening phases on Cu,Cu-carbon nanotubes(CNTs)composites were prepared using LPBF technique with Cu-CNTs mixed powder as the matrix.The formability,microstructure,mechanical properties,electrical conductivity,and thermal properties were studied.The result shows that the prepared composites have high relative density.The addition of CNTs results in inhomogeneous equiaxed grains at the edges of the molten pool and columnar grains at the center.Compared with pure copper,the overall mechanical properties of the composite are improved:tensile strength increases by 52.8%and elongation increases by 146.4%;the electrical and thermal properties are also enhanced:thermal conductivity increases by 10.8%and electrical conductivity increases by 12.7%.展开更多
Selective laser melting(SLM),as an additive manufacturing technology,has garnered widespread attention for its capability to fabricate components with complex geometries and to tailor the microstructure and mechanical...Selective laser melting(SLM),as an additive manufacturing technology,has garnered widespread attention for its capability to fabricate components with complex geometries and to tailor the microstructure and mechanical properties under specific conditions.However,the intrinsic influence mechanism of microstructure formation under non-equilibrium solidification conditions in SLM processes has not been clearly revealed.In the present work,the influence of Al concentration and process parameters on the microstructure forming mechanism of Al_(x)CoCrFeNi HEAs prepared by SLM is investigated by molecular dynamics simulation method.The simulation results show that the difference in Al content significantly affects the microstructure formation of HEAs,including the growth rate and morphology of columnar crystals,stress distribution at grain boundaries,and defect structure.In addition,the results show that increasing the substrate temperature improves the solidification formability,reduces microstructural defects,and helps reduce residual stress in Al_(x)CoCrFeNi HEAs.By analyzing the influence of heat and solute flow in the molten pool on the growth of columnar crystals,it is found that spatial fluctuations in Al concentration during the non-equilibrium solidification process inhibit the high cooling rates induced by steep temperature gradients.These findings promote the understanding of the forming mechanism of microstructure in HEAs prepared by SLM and provide theoretical guidance for designing high-performance SLM-fabricated HEAs.展开更多
The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The micr...The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.展开更多
The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evo...The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.展开更多
Laser remelting(LR)was used as an auxiliary post-treatment process for the Ti6Al4V titanium alloys fabricated by laser powder bed fusion(LPBF).Optical microscope(OM),scanning electron microscope(SEM)and electron back ...Laser remelting(LR)was used as an auxiliary post-treatment process for the Ti6Al4V titanium alloys fabricated by laser powder bed fusion(LPBF).Optical microscope(OM),scanning electron microscope(SEM)and electron back scattering diffraction(EBSD)observations showed that the grains in melted zone(MZ)transformed into equiaxial grains with an average size of 1.31μm,and the grains in heat affected zone(HAZ)were refined.Moreover,the texture intensity dropped significantly from 13.86 to 6.35 in MZ and 10.79 in HAZ.The temperature gradient(G)to solidification rate(R)ratio decreased when the laser scanning speed slowed down to a certain extent in the LR process,which effectively improved the highly preferred orientation and filled the hole defects in the surface of LPBF-Ti6Al4V.Furthermore,the hardness,wear resistance and corrosion resistance of the surface of the LPBF samples were improved by LR treatment.展开更多
Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate indiv...Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate individual investigation due to variations in their composition and fabrication processes.This study presents a comprehensive investigation into evolution of the mechanical properties,surface microstructure,and composition of Shicolon-Ⅱ fibers subjected to argon heat treatment at temperatures ranging from 1300℃to 1700℃.The Shicolon-Ⅱ fibers are composed of small-sized β-SiC grains,SiC_(x)O_(y) amorphous phase,and a minor amount of graphite microcrystals.Following treatment in an argon atmosphere at 1300℃,the fibers maintain a monofilament tensile strength of 3.620 GPa,corresponding to a retention of 98.32%.This strength diminishes to 2.875 GPa,equating to a retention of 78.08%,after treatment at 1500℃.The reduction in mechanical properties of the fibers can be ascribed to the decomposition of the amorphous phase and the growth of β-SiC grains.Furthermore,creep resistance is an essential factor influencing the long-term performance of composite materials.After treatment at temperatures above 1400℃,the high-temperature creep resistance of the fibers is significantly enhanced due to growth of β-SiC grains.This study offers valuable theoretical insights into high-temperature applications of second-generation fibers,contributing to an enhanced understanding of their performance under extreme conditions.展开更多
文摘Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively investigated.Macroscopic morphology,microstructure,and interfacial structure of the joints were analyzed using scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer(XRD).The results show that magnetic pulse welding of dissimilar Mg/Fe metals is achieved using an Al interlayer,which acts as a bridge for deformation and diffusion.Specifically,the AZ31B/AA1060 interface exhibits a typical wavy morphology,and a transition zone exists at the joint interface,which may result in an extremely complex microstructure.The microstructure of this transition zone differs from that of AZ31B magnesium and 1060 Al alloys,and it is identified as brittle intermetallic compounds(IMCs)Al_(3)Mg_(2) and Al_(12)Mg_(17).The transition zone is mainly distributed on the Al side,with the maximum thickness of Al-side transition layer reaching approximately 13.53μm.Incomplete melting layers with varying thicknesses are observed at the primary weld interface,while micron-sized hole defects appear in the transition zone of the secondary weld interface.The AA1060/DC56D interface is mainly straight,with only a small number of discontinuous transition zones distributed intermittently along the interface.These transition zones are characterized by the presence of the brittle IMC FeAl_(3),with a maximum thickness of about 4μm.
基金financially and technically supported by the National Key Laboratory Foundation of Science and Technology on Materials under Shock and Impact,Beijing Institute of Technology,China(No.WDZC2024-1)。
文摘Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic rolled SF-7055 Al alloy is elongated to form a fiber texture.Numerous proliferating dislocations in the microstructure accumulate into dislocation walls and cells,and eventually form subgrains.These subgrain boundaries divide the original grain,thereby reducing the grain size.Under severe deformation conditions,they even enable the formation of nanograins.Meanwhile,the Cu-rich precipitates in the matrix are also broken and refined under the action of large rolling stress.In the process of cryogenic rolling,the tensile strength and hardness of SF-7055 Al alloy gradually increase,while the plasticity decreases.Moreover,the fracture morphology of cryogenic rolled SF-7055 Al alloy gradually transforms to the ductile and quasi-cleavage hybrid fracture characteristics with increased reduction.
基金the financial support by the Major Science and Technology Achievement Transformation Project in Heilongjiang Province(No.ZC2023SH0075)the National Natural Science Foundation of China(Nos.52425401,U2441255,52474377,and 52371015)+1 种基金the Young Elite Scientists Sponsorship·Program by CAST(No.2021QNRC001)the Henan Provincial Key Research and Development&Promotion Special Program(No.251111231400)。
文摘The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepared by vacuum arc melting.The microstructure,mechanical properties,and related influencing mechanisms were systematically investigated.The results indicate that the solidification microstructure of the Ti46Al1.5Cr8Nb-xTa alloys comprises theγ-TiAl phase,α_(2)-Ti_(3)Al phase,and B2 phase.As the Ta content increases from 0.2 at.%to 1.0 at.%,the content ofα_(2)phase and B2 phase increases,while theγphase content decreases.Among them,the B2 phase shows the most pronounced change,being significantly refined,with its content increasing from 12.49%to 21.91%.In addition,the average size of the lamellar colony decreases from 160.65 to 94.44μm.The addition of the Ta element shifts the solidification path toward lower aluminum concentrations,leading to changes in phase content.The tantalum-induced increase in the B2 phase and enhanced supercooling at the solidification front provide the basis for lamellar colony refinement.Compressive testing at room temperature reveals that the Ti46 Al1.5 Cr8 Nb0.4 Ta alloy exhibits optimal compressive properties,achieving a compressive strength of 2,434 MPa and a compressive strain of 33.1%.The improvement of its properties is attributed to a combination of lamellar colony refinement,solid solution strengthening resulting from the incorporation of Ta element,and a reduction in the c/a of theγphase.
基金the support from the National Natural Science Foundation of China (Nos. U20A20274, 52061003)the Natural Science Foundation of Yunnan Province, China (No. 202301AT070209)the Science and Technology Major Project of Yunnan Province, China (No. 202102AG050017)。
文摘The age-hardening response,mechanical,and corrosion-resistant properties of AA7085 alloys with and without the addition of 0.3 wt.%scandium(Sc)were compared.Using advanced techniques such as aberration-corrected transmission electron microscopy and first-principles calculations,the underlying micromechanisms of Sc microalloying were revealed.Results show that the increase in strength of the AA7085-Sc alloy is mainly attributed to the decreased Al grain size and increased number density of both Al_(3)Sc@Al_(3)(Sc,Zr)core−shell nanoparticles and Sc-containingη_(p) and GP−η_(p) nanoprecipitates.Strong strain fields and evident electron transfer from Zr to the neighboring matrix Al atoms exist at the Al_(3)Sc@Al_(3)(Sc,Zr)/Al interface.The Sc doping in GP−η_(p) andη_(p) suppresses the GP−η_(p)→η_(p) transformation.Modified corrosion resistance of the AA7085-Sc alloy compared with AA7085 alloy is associated with the fine grain boundary precipitates ofη_(p)hases and narrow precipitation free zone.The reasons of property changes of AA7085 alloy after Sc microalloying are explored based on the multiscale microstructural characterization.
基金financially supported by the National Key Research and Development Program of China(Nos.2022YFB3709300,2021YFB3701000)the National Natural Science Foundation of China(Nos.52271090,52071036,U2037601,U21A2048)+1 种基金Chongqing Science and Technology Commission,China(Nos.CSTB2022TIAD-KPX0021,CSTC2024YCJHBGZXM0164,CSTB2024TIAD-KPX0001)the Fundamental Research Funds for the Central Universities,China(No.2022CDJDX-002)。
文摘The commercial AM60(Mg−6Al−0.3Mn)die-casting alloy was modified through Mn,Ce,and La micro-alloying,each at a content below 0.2 wt.%.SEM,TEM,and Micro-CT were employed to characterize the microstructures and properties of AM60 based alloys.AM60-0.2La alloy showed excellent mechanical properties.The ultimate tensile strength,yield strength,and elongation of(288.0±1.7)MPa,(158.0±1.0)MPa,and(22.0±3.0)%were achieved in AM60-0.2La alloy.Besides,AM60-0.2La alloy exhibited the best corrosion resistance(0.29 mm/a)and fluidity among the investigated four alloys.The excellent mechanical properties and corrosion resistance are mainly attributed to the grain refinement strengthening,low porosity,and low content of large shrinkage porosity,promising for super-sized integrated automotive components.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
基金Funded by Natural Science Foundation of Guangxi(No.2025GXNSFBA069565)Guangxi Science and Technology Program(No.AD25069101)Guangxi Bagui Scholars Fund。
文摘Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of recycled coral aggregate on concrete properties,this study performed a comprehensive analysis of the physical properties of recycled coral aggregate and the basic mechanical properties and microstructure of RCAC.The test results indicate that,compared to coral debris,the crushing index of recycled coral aggregate was reduced by 9.4%,while porosity decreased by 33.5%.Furthermore,RCAC retained the early strength characteristics of coral concrete,with compressive strength and flexural strength exhibiting a notable increase as the water-cement ratio decreased.Under identical conditions,the compressive strength and flexural strength of RCAC were 12.7% and 2.5% higher than coral concrete's,respectively,with porosity correspondingly reduced from 3.13% to 5.11%.This enhancement could be attributed to the new mortar filling the recycled coral aggregate.Scanning electron microscopy(SEM)analysis revealed three distinct interface transition zones within RCAC,with the‘new mortar-old mortar’interface identified as the weakest.The above findings provided a reference for the sustainable use of coral concrete in constructing offshore islands.
基金financially supported by the Natural Science Foundation of Liaoning Province of China(2022-MS-109)the Key Research and Development Program of Liaoning Province(2023JH2/101800045)the Ministry of Science and Technology of the Peoples Republic of China(ZZ2021006).
文摘The Cu-12Fe alloy has attracted significant attention due to its excellent electrical conductivity and electromagnetic shielding capability,high strength,cost-effectiveness,and recyclability.In the present work,the Cu-12Fe alloy strip with the thickness of 2.4 mm was successfully produced by twin-roll strip casting.The microstructure and properties of the Cu-12Fe alloy were tailored by cold rolling and aging treatment.The tensile strength of the as-cast strip is approximately 328 MPa and its elongation is 25%.The Fe phase randomly dispersed in the matrix,and the average size of Fe-rich phase is 2μm.Besides,enrichment of Fe phase is observed in the central layer of the strip,results in the formation of the“sandwich structure”.Moreover,the as-cast strip of Cu-12Fe was directly cold-rolled from 2.4 to 0.12 mm.The directly cold-rolled sample after aging at 450℃for 16 h(ProcessⅠ)shows excellent electrical conductivity of 69.5%IACS,the tensile strength and elongation are 513 MPa and 3.8%,the saturation magnetic flux density is 20.1 emu·g^(-1),and the coercive force is 25.2 Oe.In ProcessⅡ,the as-cast strip firstly cold-rolled to 1.2 mm,then aged at 500℃for 1.5 h,followed by cold rolling to 0.12 mm,finally aged at 450℃for 16 h.The sample after ProcessⅡshows the electrical conductivity of 66.3%IACS,the tensile strength of 533 MPa,an elongation of 3.5%,saturation magnetic flux density of 21.4 emu·g^(-1),and the coercive force of 22.3 Oe.
基金supported by the National Natural Science Foundation of China(No.52271101)Suzhou Science and Technology Project,China(Nos.SYG202312,SJC2023005,SZS2023023)+1 种基金Nanjing Major Science and Technology Project,China(No.202309015)the Opening Project of Jiangsu Key Laboratory of Advanced Structural Materials and Application Technology,China(No.ASMA202305)。
文摘To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrought Zn−0.1Mg alloy by annealing at 200℃ for varying durations.The findings reveal that the tensile strength of the alloy rapidly and significantly declines with prolonged annealing time,decreasing from 383 MPa for the as-received alloy to 102 MPa for the alloy subjected to 1440 min of annealing.The primary factors contributing to this considerable reduction in strength are static recrystallization,grain coarsening,and dislocation annihilation.Initially,the ductility of the alloy shows fluctuations,ultimately experiencing a marked decrease after extended annealing.This decline is linked to the grain growth and heightened texture intensity,while the unusual increase in ductility observed between 30 and 120 min of annealing is likely due to the formation of twins.In addition,due to rapid grain growth and an increase in precipitates and twins,the corrosion resistance of the alloy in Hank’s solution has worsened,with the corrosion rate rising from 0.037 to 0.069 mm/a following 300 min of annealing.
基金Projects(52571276,52275395,U24A20120,52475362)supported by the National Natural Science Foundation of ChinaProject(2025JJ30015)supported by the Hunan Provincial Natural Science Foundation,China+3 种基金Project(2023RC3046)supported by the Science and Technology Innovation Program of Hunan Province,ChinaProject(2023YFB4605800)supported by National Key Research and Development Program of ChinaProject(2023CXQD023)supported by the Central South University Innovation-Driven Research Programme,ChinaProject supported by the State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University,China。
文摘Zn's natural degradability and biocompatibility make it a promising candidate for implants,however,its mechanical properties remain insufficient for bone applications.In this study,the performance of Zn was enhanced by developing Zn-Cu alloys via laser powder bed fusion(LPBF).Optimal LPBF parameters for forming stable tracks were achieved by adjusting laser power and scanning speed.Under optimized conditions of 100 W and 100 mm/s,high density(99.58%)Zn-Cu alloys with improved hardness(68.2 HV)and yield strength(160 MPa)were achieved.These improvements are attributed to solid solution strengthening,segregation strengthening,and grain refinement.The Zn-Cu alloys also demonstrated favorable degradation behavior,with a rate of 0.16 mm/year.This degradation is primarily driven by micro-galvanic corrosion between the CuZn 5 phase and Zn matrix,along with refined grains and increased grain boundary density.This work demonstrates a viable strategy for fabricating Zn-based implants with enhanced structural integrity and mechanical performance via LPBF.
基金supported by National Natural Science Foundation of China(Grant No.52171032)Hebei Natural Science Foundation(Grant No.E2023501002)Fundamental Research Funds for the Central Universities(Grant No.2024GFYD003)。
文摘High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as notable solid-state welding and processing techniques,have been proved effectiveness in enhancing microstructures and mechanical properties of HEAs.This review article summarizes the current status of FSW/P of HEAs.The welding materials and conditions used for FSW/P in HEAs are reviewed and discussed.The effects of FSW/P on the evolutions of grain structure,texture,dislocation,and secondary phase for different HEAs are highlighted.Furthermore,the influences of FSW/P on the mechanical properties of various HEAs are analyzed.Finally,potential applications,challenges,and future directions of FSW/P in HEAs are forecasted.Overall,FSW/P enable to refine grains of HEAs through dynamic recrystallization and to activate diverse deformation mechanisms of HEAs through tailoring phase structures,thereby significantly improving the strength,hardness,and ductility of both single-and dual-phase HEAs.Future progress in this field will rely on comprehensive optimization of processing parameters and alloy composition,integration of multi-scale modeling with advanced characterization for in-depth exploration of microstructural mechanisms,systematic evaluation of functional properties,and effective bridging of the gap between laboratory research and industrial application.The review aims to provide an overview of recent advancements in the FSW/P of HEAs and encourage further research in this area.
基金Tianjin Municipal Natural Science Foundation(23JCYBJC00040)National Natural Science Foundation of China(52175369)。
文摘The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.
基金supported by the National Key Research and Development Program of China(No.2022YFB3404202)the National Natural Science Foundation of China(No.52271103)the Jilin Scientific and Technological Development Program,China(Nos.20220301026GX,20210301041GX)。
文摘The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding 0.2 wt.%Mn to T6-treated Al−Si−Mg alloys enhanced the corrosion resistance by promoting the formation ofα-AlFeMnSi phase,characterized by smaller absolute Volta potential values compared to eutectic Si,β-AlFeSi andπ-AlFeMgSi phases.However,the addition of 0.5 wt.%Mn and 1.0 wt.%Mn to the T6-treated Al−Si−Mg alloys increased the size of theα-AlFeMnSi phase.This decreased the properties of T6-treated Al−Si−Mg alloys.Therefore,the optimum Mn content was 0.2 wt.%,providing a novel approach for synergistically enhancing mechanical properties and corrosion resistance of Al−Si−Mg alloys.
基金Funded by the National Key Research Program(No.2024-1129-954-112)National Natural Science Foundation of China(No.52372033)Guangxi Science and Technology Major Program(No.AA24263054)。
文摘In current research,Li_(2)O-Al_(2)O_(3)-SiO_(2)glass-ceramics were prepared by conventional meltquenching and subsequent heat treatment method.The effect of Al_(2)O_(3)content on microstructures,thermal properties,crystallization behaviours and mechanical properties were investigated.FTIR,Raman spectroscopy and nuclear magnetic resonance spectroscopy microstructure analysis showed that the silico-oxygen network was damaged,while the increase of[AlO_(4)]content repaired the glass network,and finally made the glass network have better connectivity,with the decrease of SiO_(2).The thermal analysis confirmed the increasing glass transition and crystallization temperatures from growing Al_(2)O_(3)content.In addition,different crystal phases can be precipitated in the glass matrix,such as LiAlSi_(4)O_(10),Li_(2)Si_(2)O_(5) in glass with low Al_(2)O_(3)content,the combination of Li_xAl_xSi_(1-x)O_(2),LiAlSi_(3)O_(8),Li_(2)SiO_(3)in glass with intermediate Al_(2)O_(3)content,and the combination of LiAlSi_(2)O_(6),SiO_(2)in glass with high Al_(2)O_(3)content.The hardness of as-prepared glass gradually increases with the increase of the Al_(2)O_(3)content.The Vickers hardness of the glass-ceramics is highly dependent on the Al_(2)O_(3)content in the glass and the heat treatment temperatures,reaching a maximum of 10.11 GPa.Scanning electron microscope images show that the crystals change from spherical to massive and finally to sheet.The change of glass structure,crystal phase and morphology is the main reason for the different mechanical properties.
基金National Key Research and Development Program of China(2023YFB4606400)Supported by Longmen Laboratory Frontier Exploration Topics(LMQYTSKT003)。
文摘Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the effects of strengthening phases on Cu,Cu-carbon nanotubes(CNTs)composites were prepared using LPBF technique with Cu-CNTs mixed powder as the matrix.The formability,microstructure,mechanical properties,electrical conductivity,and thermal properties were studied.The result shows that the prepared composites have high relative density.The addition of CNTs results in inhomogeneous equiaxed grains at the edges of the molten pool and columnar grains at the center.Compared with pure copper,the overall mechanical properties of the composite are improved:tensile strength increases by 52.8%and elongation increases by 146.4%;the electrical and thermal properties are also enhanced:thermal conductivity increases by 10.8%and electrical conductivity increases by 12.7%.
基金supported by the National Natural Science Foundation of China(Grant No.12102133).
文摘Selective laser melting(SLM),as an additive manufacturing technology,has garnered widespread attention for its capability to fabricate components with complex geometries and to tailor the microstructure and mechanical properties under specific conditions.However,the intrinsic influence mechanism of microstructure formation under non-equilibrium solidification conditions in SLM processes has not been clearly revealed.In the present work,the influence of Al concentration and process parameters on the microstructure forming mechanism of Al_(x)CoCrFeNi HEAs prepared by SLM is investigated by molecular dynamics simulation method.The simulation results show that the difference in Al content significantly affects the microstructure formation of HEAs,including the growth rate and morphology of columnar crystals,stress distribution at grain boundaries,and defect structure.In addition,the results show that increasing the substrate temperature improves the solidification formability,reduces microstructural defects,and helps reduce residual stress in Al_(x)CoCrFeNi HEAs.By analyzing the influence of heat and solute flow in the molten pool on the growth of columnar crystals,it is found that spatial fluctuations in Al concentration during the non-equilibrium solidification process inhibit the high cooling rates induced by steep temperature gradients.These findings promote the understanding of the forming mechanism of microstructure in HEAs prepared by SLM and provide theoretical guidance for designing high-performance SLM-fabricated HEAs.
基金supported by the National Natural Science Foundation of China(No.51874368)。
文摘The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.
基金support of the Research and Development Program in Key Areas of Guangdong Province,China(No.2019B090907001)the Science and Technology Program of Guangdong Province,China(No.2014B010129002)the National Key R&D Program of China(No.2017YFB0305800)。
文摘The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.
基金supported by the National Natural Science Foundation of China(No.51871243)the National Key Laboratory of Strength and Structural Integrity,China(No.ASSIKFJJ202304001)+3 种基金the State Key Laboratory of Precision Blasting and Hubei Key Laboratory of Blasting Engineering,China(No.PBSKL2022C01)the Guangdong-Hong Kong-Macao Joint Laboratory for Neutron Scattering Science and Technology,China(No.HT-CSNS-DG-CD-0092/2021)the Shock and Vibration of Engineering Materials and Structures Key Laboratory of Sichuan Province,China(No.22kfgk06)the Hubei Longzhong Laboratory,China(No.2022KF-08)。
文摘Laser remelting(LR)was used as an auxiliary post-treatment process for the Ti6Al4V titanium alloys fabricated by laser powder bed fusion(LPBF).Optical microscope(OM),scanning electron microscope(SEM)and electron back scattering diffraction(EBSD)observations showed that the grains in melted zone(MZ)transformed into equiaxial grains with an average size of 1.31μm,and the grains in heat affected zone(HAZ)were refined.Moreover,the texture intensity dropped significantly from 13.86 to 6.35 in MZ and 10.79 in HAZ.The temperature gradient(G)to solidification rate(R)ratio decreased when the laser scanning speed slowed down to a certain extent in the LR process,which effectively improved the highly preferred orientation and filled the hole defects in the surface of LPBF-Ti6Al4V.Furthermore,the hardness,wear resistance and corrosion resistance of the surface of the LPBF samples were improved by LR treatment.
基金National Natural Science Foundation of China(52172108)National Key R&D Program of China(2022YFB3707700)Strategic Priority Research Program of the Chinese Academy of Sciences(XDC0144005)。
文摘Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate individual investigation due to variations in their composition and fabrication processes.This study presents a comprehensive investigation into evolution of the mechanical properties,surface microstructure,and composition of Shicolon-Ⅱ fibers subjected to argon heat treatment at temperatures ranging from 1300℃to 1700℃.The Shicolon-Ⅱ fibers are composed of small-sized β-SiC grains,SiC_(x)O_(y) amorphous phase,and a minor amount of graphite microcrystals.Following treatment in an argon atmosphere at 1300℃,the fibers maintain a monofilament tensile strength of 3.620 GPa,corresponding to a retention of 98.32%.This strength diminishes to 2.875 GPa,equating to a retention of 78.08%,after treatment at 1500℃.The reduction in mechanical properties of the fibers can be ascribed to the decomposition of the amorphous phase and the growth of β-SiC grains.Furthermore,creep resistance is an essential factor influencing the long-term performance of composite materials.After treatment at temperatures above 1400℃,the high-temperature creep resistance of the fibers is significantly enhanced due to growth of β-SiC grains.This study offers valuable theoretical insights into high-temperature applications of second-generation fibers,contributing to an enhanced understanding of their performance under extreme conditions.
