Mussels are common anchoring organisms that adhere to the surfaces of various substrates with their byssus.The adhesion of mussel to substrates is contingent upon the presence of mussel foot proteins,of which Mytilus ...Mussels are common anchoring organisms that adhere to the surfaces of various substrates with their byssus.The adhesion of mussel to substrates is contingent upon the presence of mussel foot proteins,of which Mytilus edulis foot protein-1(Mefp-1)has been identified as the most abundant protein.It has been found that lipids are involved in the mussel adhesion process and can facilitate Mefp-1adhesion.In this research,the adhesion behavior of Mefp-1 on various substrate surfaces under the effect of typical seawater cations with or without the presence of lipid were investigated using a quartz crystal microbalance with dissipation(QCM-D).Results indicate that the presence of cations Ca^(2+),Mg^(2+),Na^(+),and K^(+)leads to varying degrees of reduction in the adhesion performance of Mefp-1 on different substrates.The degree of this reduction,however,was much alleviated in the presence of palmitic acid,which is involved in the mussel adhesion process.Therefore,the involvement of palmitic acid is advantageous for mussel protein adhesion to the substrate surface in the marine environment.This study illustrated the significant contribution of palmitic acid to mussel adhesion,which can help to better understand biofouling mechanisms and develop biomimetic adhesive materials.展开更多
To address the challenge of achieving both high sensitivity and a high quality factor in quartz crystal microbalance(QCM)humidity sensors,a nanodiamond(ND)/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was fab...To address the challenge of achieving both high sensitivity and a high quality factor in quartz crystal microbalance(QCM)humidity sensors,a nanodiamond(ND)/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was fabricated.The material characteristics of ND,Ti_(3)C_(2)MXene,and ND/Ti_(3)C_(2)MXene composite were analyzed by transmission electron microscopy(TEM)and Fourier transform infrared(FTIR)spectroscopy.The experimental results demonstrated that the hydrophilic ND nanoparticles coated on Ti_(3)C_(2) MXene nanosheet prevented the self-stacking of Ti_(3)C_(2)MXene and enhanced the sensitivity of Ti_(3)C_(2) MXene-based QCM humidity sensor.Moreover,the high mechanical modulus of Ti_(3)C_(2) MXene material helped ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor to achieve a high quality factor(>20,000).ND/Ti_(3)C_(2)MXene compositecoated QCM humidity sensor exhibited a sensitivity of 82.45 Hz/%RH,a humidity hysteresis of 1.1%RH,fast response/recovery times,acceptable repeatability,and good stability from 11.3%RH to 97.3%RH.The response mechanism of ND/Ti_(3)C_(2) MXene composite-coated QCM humidity sensor was analyzed in combination with a bi-exponential kinetic adsorption model.Finally,the potential application of ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was demonstrated through its frequency response to wooden blocks with different moisture contents.展开更多
As humidity is one of the most widely demanded environmental parameters,the precision of its detection is significant.An advanced humidity sensor will improve the validity of the humidity monitoring system.In this stu...As humidity is one of the most widely demanded environmental parameters,the precision of its detection is significant.An advanced humidity sensor will improve the validity of the humidity monitoring system.In this study,a facile chemical layer-by-layer self-assembly(CLS)method was developed for fabricating graphene oxide(GO)/polyethyleneimine(PEI)multilayer films.Owing to the chemical bonding between the PEI and GO,and the intrinsic stickiness of the PEI,layered films with different numbers of layers were successfully prepared using the CLS method and confirmed through ultraviolet-visible(UV-Vis)spectroscopy and the mass loading of quartz crystal microbalance(QCM).Morphological measurements revealed that the roughness and thickness of the films increased exponentially with the number of bilayers.The GO/PEI films were deposited on QCM electrodes using the CLS method to produce the humidity sensors.The humidity measurement results showed a high sensitivity(37.84 Hz/%RH)and rapid response/recovery(<5 s/8 s)of the optimal sensor,which was superior to that of recently developed QCM sensors.展开更多
The fast and accurate identification of nerve tracts is critical for successful nerve anastomosis. Taking advantage of differences in acetylcholinesterase content between the spinal ventral and dorsal roots, we develo...The fast and accurate identification of nerve tracts is critical for successful nerve anastomosis. Taking advantage of differences in acetylcholinesterase content between the spinal ventral and dorsal roots, we developed a novel quartz crystal microbalance method to distinguish between these nerves based on acetylcholinesterase antibody reactivity. The acetylcholinesterase antibody was immobilized on the electrode surface of a quartz crystal microbalance and reacted with the acetylcholinesterase in sample solution. The formed antigen and antibody complexes added to the mass of the electrode inducing a change in frequency of the electrode. The spinal ventral and dorsal roots were distinguished by the change in frequency. The ventral and dorsal roots were cut into 1 to 2-mm long segments and then soaked in 250 pL PBS. Acetylcholinesterase antibody was immobilized on the quartz crystal microbalance gold electrode surface. The results revealed that in 10 minutes, both spinal ventral and dorsal roots induced a frequency change; however, the frequency change induced by the ventral roots was notably higher than that induced by the dorsal roots. No change was induced by bovine serum albumin or PBS. These results clearly demonstrate that a quartz crystal microbalance sensor can be used as a rapid, highly sensitive and accurate detection tool for the quick identification of spinal nerve roots intraoperatively.展开更多
In this study, we have used a direct immunoassay where the simple binding between antigen and an antibody is detected. Immunoassays were performed in a drop system, monitoring the frequency decrease of the quartz-crys...In this study, we have used a direct immunoassay where the simple binding between antigen and an antibody is detected. Immunoassays were performed in a drop system, monitoring the frequency decrease of the quartz-crystal microbalance device because of mass increasing during immunoreaction. The QCM sensor was coated on both sides by gold electrodes, only one side of the crystal (liquid side) was in contact with the solution;the other side (contact side) was always dry. We tested a piezoelectric immunosensor for aflatoxin B1 (AFLA-B1) mycotoxin detection through the immo- bilization of DSP-anti-AFLAB1 antibody (AFLA-B1-Ab anti AFLAB1) on gold-coated quartz crystals (AT-cut/5 MHz). The DSP (3,3’-Dithiodipropionic-acid-di-N-hydroxysuccinimide ester) was used for the covalent attachment of the proteins. The piezoelectric crystal electrodes were pretreated by DSP for 15 min, rinsed with water and dried in a gentle flow of nitrogen gas. Then the DSP-coated crystals were installed in a sample holder and exposed to the anti-AFLAB1 antibody and to the AFLA-BI. Frequency and resistance shifts (Δf and ΔR) were measured simultaneously. Δf versus AFLA-BI concentrations in the range of 0.5 - 10 ppb exhibited a perfect linear correlation with a coefficient of above 0.998.展开更多
Using the langasite crystal microbalance (LCM), the trends in film thickness produced by means of the chemical vapor deposition using trichlorosilane gas, monomethylsilane gas and their mixed gas were observed at 600?...Using the langasite crystal microbalance (LCM), the trends in film thickness produced by means of the chemical vapor deposition using trichlorosilane gas, monomethylsilane gas and their mixed gas were observed at 600?C and evaluated by comparison with the information from a transmission electron microscope (TEM). The crystalline silicon film thickness from trichlorosilane gas was comparable to that of an amorphous silicon carbide film from monomethylsilane gas. The film obtained from the gas mixture was amorphous and was the thinnest in this study. Because the thickness trend obtained by the LCM agreed with that by the TEM, the LCM is shown to be a convenient evaluation tool for the behavior of various film deposition.展开更多
A dichlorosilane gas and a trichlorosilane gas in ambient hydrogen were evaluated to show their different gas flow motions in a slim vertical cold wall chemical vapor deposition reactor for the Minimal Fab system. Thi...A dichlorosilane gas and a trichlorosilane gas in ambient hydrogen were evaluated to show their different gas flow motions in a slim vertical cold wall chemical vapor deposition reactor for the Minimal Fab system. This evaluation was performed for improving and controlling the film qualities and the productivities, using two quartz crystal microbalances (QCM) installed at the </span><span style="font-family:Verdana;">inlet and exhaust of the chamber by taking into account that the QCM frequency corresponds to the real time changes in the gas properties.</span><span style="font-family:Verdana;"> Typically, the time period approaching from the inlet to the exhaust was shorter for the trichlorosilane gas than that for the dichlorosilane gas. The trichlorosilane gas was shown to move like plug flow, while the dichlorosilane gas seemed to be well mixed in the entire chamber.展开更多
A quartz crystal microbalance （QCM） is used to determine the phase equilibrium of paclitaxel-carbon dioxide system in the pressure range of 0-11 MPa and at temperatures of 35 °C,40 °C and 45 °C.The ex...A quartz crystal microbalance （QCM） is used to determine the phase equilibrium of paclitaxel-carbon dioxide system in the pressure range of 0-11 MPa and at temperatures of 35 °C,40 °C and 45 °C.The experimental results indicated that gaseous CO2 could be absorbed poorly into paclitaxel.The swelling of paclitaxel film in CO2 was observed before paclitaxel dissolved into supercritical carbon dioxide （ScCO2） with the increase of pressure.It was found that ScCO2 was not a good solvent for paclitaxel.The mole fraction of paclitaxel in ScCO2 was in the range of （4.5×10-9）-（7.8×10-9） under all our experimental conditions.Therefore,a much higher pressure than the CO2 supercritical point and/or a cosolvent must be used in any processes wherever paclitaxel dissolution in ScCO2 is required.展开更多
Pd was electrochemically deposited on gold-coated quartz crystals at nanogram-level. The coulombic efficiency and initial nucleation and growth mechanism of potentiostatic Pd deposition were investigated via in situ e...Pd was electrochemically deposited on gold-coated quartz crystals at nanogram-level. The coulombic efficiency and initial nucleation and growth mechanism of potentiostatic Pd deposition were investigated via in situ electrochemical quartz crystal microbalance（EQCM）. The coulombic efficieneies are 84%, 93% and 95% for Pd deposition at 0.3, 0.2 and 0.1 V（vs. SCE）, respectively. The results of chronoamperometric measurements show that the Pd deposition proceeded by an instantaneous nucleation（at 0.3 V） or progressive nucleation（at 0.2 and 0.1 V） in a three-dimensional（3D） growth mode. The catalytic activity of Pd-based electrocatalyst for ethanol oxidation was characterized in an alkaline solution. It was found that the highest mass activity for ethanol oxidation on Pd-based electrocatalyst is 1.8× 10^4 A/（g Pd） deposited at 0.3 V for 5 s.展开更多
The in situ electrochemical quartz crystal microbalance（EQCM） technique was used to investigate the ion transport of immobilized heteropolyanions at a self-assembled monolayer（SAM） modified gold electrode during e...The in situ electrochemical quartz crystal microbalance（EQCM） technique was used to investigate the ion transport of immobilized heteropolyanions at a self-assembled monolayer（SAM） modified gold electrode during electrochemical redox process.A mixed transfer method was presented to analyse the abnormal change of resonant frequency based on the simultaneous insertion/extraction of different ions.The results indicate that the migration of HSO4-anions was indispensable in the redox process of the heteropolyanions in a 1 mol/L H2SO4 solution and played a key role in the abnormal change of the resonant frequency.Such a change was attributed to different packing densities derived by means of differently immobilized methods.展开更多
The adsorption of fibrinogen can be used as a quick indicator of surface haemocompatibility because of its prominent role in coagulation and platelet adhesion. In this work the molecular interaction between fibrinogen...The adsorption of fibrinogen can be used as a quick indicator of surface haemocompatibility because of its prominent role in coagulation and platelet adhesion. In this work the molecular interaction between fibrinogen and a modified titanium oxide surface/platelet has been studied by quartz crystal microbalanee with dissipation （QCM-D） in situ. In order to further characterize the conformation of adsorbed fibrinogen, αC and γ-chain antibody were used to check the orientation and denaturation of fibrinogen on solid surface. QCM-D investiga- tions revealed the fibrinogen have the trend to adsorb on hydropllilic surface in a side-on orientation by positively charged αC domains, which would reduce the exposure of platelet bonding site on γ chain and enable less platelet adhesion and be activated. These obser- vations suggest that certain conformations of adsorbed fibrinogen are less platelet adhesive than others, which opens a possibility for creating a non-platelet adhesive substrates.展开更多
The effect of salt concentration on layer-by-layer deposition of poly（sodium 4-styrene sulfonate） （PSSS）/poly（vinylbenzyl trimethylammonium chloride） （PVTC） was investigated by use of quartz crystal microbalan...The effect of salt concentration on layer-by-layer deposition of poly（sodium 4-styrene sulfonate） （PSSS）/poly（vinylbenzyl trimethylammonium chloride） （PVTC） was investigated by use of quartz crystal microbalance with dissipation （QCM-D）. The changes in frequency and dissipation demonstrate that the addition of NaC1 leads the thickness of PSSS/PVTC multilayer to increase. The deposition of PSSS/PVTC is dominated by surface charge overcompensation level at lower salt concentrations. However, it is mainly determined by the interpenetration of polyelectrolytes at a higher salt concentration, as reflected in the oscillation of dissipation change.展开更多
The quartz crystal microbalance（QCM） is an important tool that can sense nanogram changes in mass. The hybrid temperature effect on a QCM resonator in aqueous solutions leads to unconvincing detection results. Contr...The quartz crystal microbalance（QCM） is an important tool that can sense nanogram changes in mass. The hybrid temperature effect on a QCM resonator in aqueous solutions leads to unconvincing detection results. Control of the temperature effect is one of the keys when using the QCM for high precision measurements. Based on the Sauerbrey＇s and Kanazawa＇s theories, we proposed a method for enhancing the accuracy of the QCM measurement, which takes into account not only the thermal variations of viscosity and density but also the thermal behavior of the QCM resonator. We presented an improved Sauerbrey equation that can be used to effectively compensate the drift of the QCM resonator. These results will play a significant role when applying the QCM at the room temperature.展开更多
In this study,a label-free,portable and reproducible immunochip based on quartz crystal microbalance(QCM)was developed for the qualitative detection ofβ-lactoglobulin(β-LG),an allergen,in milk products.Experimental ...In this study,a label-free,portable and reproducible immunochip based on quartz crystal microbalance(QCM)was developed for the qualitative detection ofβ-lactoglobulin(β-LG),an allergen,in milk products.Experimental parameters in the fabrication and regeneration procedure such as pH of the coupling microenvironment,amount of anti-β-LG antibody and regeneration reagent were optimized in detail.Under optimal conditions,the proposed QCM immunochip exhibited good recognition of β-LG,with a calibration curve of ΔF=12.877 C_(β-LG)^(0.4809)(R^(2)=0.9982)and limit of detection of 0.04μg/mL.Additionally,this portable QCM immunochip had good stability,high specificity,and no obvious cross-reaction to three other milk proteins(α-casein,α-lactalbumin,and lactoferrin).It could compete a qualitative measurement within5 min,and could be reused at least ten times.In the β-LG analysis of actual milk samples,the developed QCM immunochip yielded reliable and accurate results,which correlated strongly with those from the standard HPLC method(R^(2)=0.9969).Thus,the portable,stable,and reproducible QCM immunochip developed in this study allowed the rapid,cost-effectively and sensitively measure theβ-LG in milk products.展开更多
The gravimetric analysis of electrodeposited nickel is demonstrated using electrochemical quartz crystal microbalance (EQCM) where the nickel coatings come from a solution of the metal chloride salt separately in eith...The gravimetric analysis of electrodeposited nickel is demonstrated using electrochemical quartz crystal microbalance (EQCM) where the nickel coatings come from a solution of the metal chloride salt separately in either a1choline chloride: 2 ethylene glycol (ethaline) or 1 choline chloride: 2 urea (reline) based ionic liquid. The possibility of adapting the Quartz Crystal Microbalance EQCM (which measures the mass attached to the electrode) to probe kinetics of electrochemically-driven solid state phase transformations has been explored in a Ni electrodeposition in absence and presence of complexing agents ethylene diamine en and acetylacetonate acac from both electrolytes ethaline and reline. The study shows that the current efficiency and the rate of deposition of nickel coatings obtained from ethaline and reline baths in absence of brighteners en and acac are different, and the addition of en and acac to both ionic liquid solutions results in a significant decrease current. And the associated growth rate will also be decreased, suggesting that the en acac stops the formation and growth of Ni nuclei. This suggests that the mechanism of growth is changed.展开更多
Nanoparticles are playing an increasingly important role in the development of biosensors. The sensitivity and performance of biosensors are being improved by using Nanoparticles for their construction. The use of the...Nanoparticles are playing an increasingly important role in the development of biosensors. The sensitivity and performance of biosensors are being improved by using Nanoparticles for their construction. The use of these Nanoparticles has allowed the introduction of many new signal transduction technologies in biosensors. In this report, a comprehensive review of application of nanoparticles in Quartz Crystal Microbalance biosensors is presented. The main advantages of QCM in sensing fields include high sensitivity, high stability, fast response and low cost. In addition, it provides label-free detection capability for bio-sensing applications. Firstly, basic QCM’s design and characterization are described. Next, QCM biosensors based on modification of quartz substrate structure and their applications are digested. Nanoparticles and their utilizationin analysis are then illustrated. These include Nanoparticles in bio applications that cover Nanoparticles in Quartz Crystal Microbalance biosensors.展开更多
We have investigated the interactions between phospholipid monolayers and volatile anest-hatics. Two monolayers (dihexadecyl phosphate (DHP) and dipalmitoyl phosphatidyl choline (DPPC) and two anesthetics (halothane a...We have investigated the interactions between phospholipid monolayers and volatile anest-hatics. Two monolayers (dihexadecyl phosphate (DHP) and dipalmitoyl phosphatidyl choline (DPPC) and two anesthetics (halothane and enflurane) were used to observe these interac-tions using a highly sensitive quartz crystal microbalance (HS-QCM). The concentration of each anesthetic in aqueous solution was kept at 4 mM. The frequency of QCM showed no change when halothane was added to the DHP monolayer, however, it responded and de-creased when interaction occurred with DPPC monolayer. In case of enflurane addition the frequency decreased in both the monolayers of DHP and DPPC. The frequency change followed the following order of monolayer-anesthetic interactions: DHP-halothane <DPPC-halothane <DHP-enflurane <DPPC-enflurane. These re-sults showed that the response of anesthetics to the monolayers i.e. the physisorption not only depends on the anesthetic structure, the type of anesthetic hydrate formed, but also the hydrophilic polar group structure of the monolayer or the monolayer/water interface had an important role in physisorption.展开更多
We are developing methods to quantify antibody interactions that include a quartz crystal microbalance (QCM) system to measure, on a molecular basis, the interaction of p53 and anti-p53 antibodies. Previously, as a mo...We are developing methods to quantify antibody interactions that include a quartz crystal microbalance (QCM) system to measure, on a molecular basis, the interaction of p53 and anti-p53 antibodies. Previously, as a model system, we developed a measurement device consisting of p53 protein (human wild type), characterized by mass spectroscopy and immobilized at various concentrations on a glass slide. The device is designed as a control to be used with immunohistochemical (IHC) assays that incorporate commercially available anti-p53 antibodies and probes. In the current study, p53 protein is covalently immobilized on a silicon dioxide-coated quartz crystal and the resonance frequency shift is followed in-situ. The functionalized sensor is then incubated with the anti-p53 antibody, which provides a direct gravimetric measure of the antibody-antigen binding. This previously described method allows the comparison of the surface immobilized protein concentrations with estimates obtained by fluorescence measurement. The p53 functionalized QCM system offers an independent measure of surface immobilized protein concentration and is essential in development of our IHC calibration prototypes. These results provide a benchmark for comparing antibody systems that may be used in developing other molecular diagnostic assays such as immunocytochemical analysis and the detection of biomarker proteins in blood and urine.展开更多
基金Supported by the National Natural Science Foundation of China(No.41776177)the Qingdao Marine Science and Technology Pilot National Laboratory Fund(Nos.2016ASKJ14,QNLM2016ORP0403)。
文摘Mussels are common anchoring organisms that adhere to the surfaces of various substrates with their byssus.The adhesion of mussel to substrates is contingent upon the presence of mussel foot proteins,of which Mytilus edulis foot protein-1(Mefp-1)has been identified as the most abundant protein.It has been found that lipids are involved in the mussel adhesion process and can facilitate Mefp-1adhesion.In this research,the adhesion behavior of Mefp-1 on various substrate surfaces under the effect of typical seawater cations with or without the presence of lipid were investigated using a quartz crystal microbalance with dissipation(QCM-D).Results indicate that the presence of cations Ca^(2+),Mg^(2+),Na^(+),and K^(+)leads to varying degrees of reduction in the adhesion performance of Mefp-1 on different substrates.The degree of this reduction,however,was much alleviated in the presence of palmitic acid,which is involved in the mussel adhesion process.Therefore,the involvement of palmitic acid is advantageous for mussel protein adhesion to the substrate surface in the marine environment.This study illustrated the significant contribution of palmitic acid to mussel adhesion,which can help to better understand biofouling mechanisms and develop biomimetic adhesive materials.
基金financially supported by the Project funded by the National Natural Science Foundation of China(No.61401047)the China Postdoctoral Science Foundation(No.2018M633349)+1 种基金the Oversea Students Funding Project of the Department of Human Resources and Social Security of Sichuanthe Scientific Research Foundation of CUIT(No.KYQN202210)。
文摘To address the challenge of achieving both high sensitivity and a high quality factor in quartz crystal microbalance(QCM)humidity sensors,a nanodiamond(ND)/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was fabricated.The material characteristics of ND,Ti_(3)C_(2)MXene,and ND/Ti_(3)C_(2)MXene composite were analyzed by transmission electron microscopy(TEM)and Fourier transform infrared(FTIR)spectroscopy.The experimental results demonstrated that the hydrophilic ND nanoparticles coated on Ti_(3)C_(2) MXene nanosheet prevented the self-stacking of Ti_(3)C_(2)MXene and enhanced the sensitivity of Ti_(3)C_(2) MXene-based QCM humidity sensor.Moreover,the high mechanical modulus of Ti_(3)C_(2) MXene material helped ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor to achieve a high quality factor(>20,000).ND/Ti_(3)C_(2)MXene compositecoated QCM humidity sensor exhibited a sensitivity of 82.45 Hz/%RH,a humidity hysteresis of 1.1%RH,fast response/recovery times,acceptable repeatability,and good stability from 11.3%RH to 97.3%RH.The response mechanism of ND/Ti_(3)C_(2) MXene composite-coated QCM humidity sensor was analyzed in combination with a bi-exponential kinetic adsorption model.Finally,the potential application of ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was demonstrated through its frequency response to wooden blocks with different moisture contents.
基金financially supported by the National Natural Science Foundation of China(No.U19A2070)the National Science Funds for Excellent Young Scholars of China(No.61822106)the National Science Funds for Creative Research Groups of China(No.61421002)。
文摘As humidity is one of the most widely demanded environmental parameters,the precision of its detection is significant.An advanced humidity sensor will improve the validity of the humidity monitoring system.In this study,a facile chemical layer-by-layer self-assembly(CLS)method was developed for fabricating graphene oxide(GO)/polyethyleneimine(PEI)multilayer films.Owing to the chemical bonding between the PEI and GO,and the intrinsic stickiness of the PEI,layered films with different numbers of layers were successfully prepared using the CLS method and confirmed through ultraviolet-visible(UV-Vis)spectroscopy and the mass loading of quartz crystal microbalance(QCM).Morphological measurements revealed that the roughness and thickness of the films increased exponentially with the number of bilayers.The GO/PEI films were deposited on QCM electrodes using the CLS method to produce the humidity sensors.The humidity measurement results showed a high sensitivity(37.84 Hz/%RH)and rapid response/recovery(<5 s/8 s)of the optimal sensor,which was superior to that of recently developed QCM sensors.
基金supported by the National Natural Science Foundation of China,No. 30973058,81171694Jiangsu Province Natural Science Foundation,No. BE2010743+2 种基金Jiangsu Graduate Student Innovation Project,No.CXZZ11_0721the Program for Development of Innovative Research Team in the First Affiliated Hospital of Nanjing Medical University,No. IRT-015a Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘The fast and accurate identification of nerve tracts is critical for successful nerve anastomosis. Taking advantage of differences in acetylcholinesterase content between the spinal ventral and dorsal roots, we developed a novel quartz crystal microbalance method to distinguish between these nerves based on acetylcholinesterase antibody reactivity. The acetylcholinesterase antibody was immobilized on the electrode surface of a quartz crystal microbalance and reacted with the acetylcholinesterase in sample solution. The formed antigen and antibody complexes added to the mass of the electrode inducing a change in frequency of the electrode. The spinal ventral and dorsal roots were distinguished by the change in frequency. The ventral and dorsal roots were cut into 1 to 2-mm long segments and then soaked in 250 pL PBS. Acetylcholinesterase antibody was immobilized on the quartz crystal microbalance gold electrode surface. The results revealed that in 10 minutes, both spinal ventral and dorsal roots induced a frequency change; however, the frequency change induced by the ventral roots was notably higher than that induced by the dorsal roots. No change was induced by bovine serum albumin or PBS. These results clearly demonstrate that a quartz crystal microbalance sensor can be used as a rapid, highly sensitive and accurate detection tool for the quick identification of spinal nerve roots intraoperatively.
文摘In this study, we have used a direct immunoassay where the simple binding between antigen and an antibody is detected. Immunoassays were performed in a drop system, monitoring the frequency decrease of the quartz-crystal microbalance device because of mass increasing during immunoreaction. The QCM sensor was coated on both sides by gold electrodes, only one side of the crystal (liquid side) was in contact with the solution;the other side (contact side) was always dry. We tested a piezoelectric immunosensor for aflatoxin B1 (AFLA-B1) mycotoxin detection through the immo- bilization of DSP-anti-AFLAB1 antibody (AFLA-B1-Ab anti AFLAB1) on gold-coated quartz crystals (AT-cut/5 MHz). The DSP (3,3’-Dithiodipropionic-acid-di-N-hydroxysuccinimide ester) was used for the covalent attachment of the proteins. The piezoelectric crystal electrodes were pretreated by DSP for 15 min, rinsed with water and dried in a gentle flow of nitrogen gas. Then the DSP-coated crystals were installed in a sample holder and exposed to the anti-AFLAB1 antibody and to the AFLA-BI. Frequency and resistance shifts (Δf and ΔR) were measured simultaneously. Δf versus AFLA-BI concentrations in the range of 0.5 - 10 ppb exhibited a perfect linear correlation with a coefficient of above 0.998.
文摘Using the langasite crystal microbalance (LCM), the trends in film thickness produced by means of the chemical vapor deposition using trichlorosilane gas, monomethylsilane gas and their mixed gas were observed at 600?C and evaluated by comparison with the information from a transmission electron microscope (TEM). The crystalline silicon film thickness from trichlorosilane gas was comparable to that of an amorphous silicon carbide film from monomethylsilane gas. The film obtained from the gas mixture was amorphous and was the thinnest in this study. Because the thickness trend obtained by the LCM agreed with that by the TEM, the LCM is shown to be a convenient evaluation tool for the behavior of various film deposition.
文摘A dichlorosilane gas and a trichlorosilane gas in ambient hydrogen were evaluated to show their different gas flow motions in a slim vertical cold wall chemical vapor deposition reactor for the Minimal Fab system. This evaluation was performed for improving and controlling the film qualities and the productivities, using two quartz crystal microbalances (QCM) installed at the </span><span style="font-family:Verdana;">inlet and exhaust of the chamber by taking into account that the QCM frequency corresponds to the real time changes in the gas properties.</span><span style="font-family:Verdana;"> Typically, the time period approaching from the inlet to the exhaust was shorter for the trichlorosilane gas than that for the dichlorosilane gas. The trichlorosilane gas was shown to move like plug flow, while the dichlorosilane gas seemed to be well mixed in the entire chamber.
基金Supported by the Jiangsu High-tech Project(BG2006038)
文摘A quartz crystal microbalance （QCM） is used to determine the phase equilibrium of paclitaxel-carbon dioxide system in the pressure range of 0-11 MPa and at temperatures of 35 °C,40 °C and 45 °C.The experimental results indicated that gaseous CO2 could be absorbed poorly into paclitaxel.The swelling of paclitaxel film in CO2 was observed before paclitaxel dissolved into supercritical carbon dioxide （ScCO2） with the increase of pressure.It was found that ScCO2 was not a good solvent for paclitaxel.The mole fraction of paclitaxel in ScCO2 was in the range of （4.5×10-9）-（7.8×10-9） under all our experimental conditions.Therefore,a much higher pressure than the CO2 supercritical point and/or a cosolvent must be used in any processes wherever paclitaxel dissolution in ScCO2 is required.
基金Supported by the Guangdong Science and Technology Key Projects, China(Nos.2007A010700001, 2007B090400032)Guangzhou Science and Technology Key Projects, China(Nos.2007Z1-D0051, SKT[2007]17-11) the Scientific Research Foundation for Young Teachers of the Sun Yat-Sen University, China(No.2006-31000-1131214)
文摘Pd was electrochemically deposited on gold-coated quartz crystals at nanogram-level. The coulombic efficiency and initial nucleation and growth mechanism of potentiostatic Pd deposition were investigated via in situ electrochemical quartz crystal microbalance（EQCM）. The coulombic efficieneies are 84%, 93% and 95% for Pd deposition at 0.3, 0.2 and 0.1 V（vs. SCE）, respectively. The results of chronoamperometric measurements show that the Pd deposition proceeded by an instantaneous nucleation（at 0.3 V） or progressive nucleation（at 0.2 and 0.1 V） in a three-dimensional（3D） growth mode. The catalytic activity of Pd-based electrocatalyst for ethanol oxidation was characterized in an alkaline solution. It was found that the highest mass activity for ethanol oxidation on Pd-based electrocatalyst is 1.8× 10^4 A/（g Pd） deposited at 0.3 V for 5 s.
基金Supported by the Science Foundation for Young Teachers of Northeast Normal University,China(No.20081001)
文摘The in situ electrochemical quartz crystal microbalance（EQCM） technique was used to investigate the ion transport of immobilized heteropolyanions at a self-assembled monolayer（SAM） modified gold electrode during electrochemical redox process.A mixed transfer method was presented to analyse the abnormal change of resonant frequency based on the simultaneous insertion/extraction of different ions.The results indicate that the migration of HSO4-anions was indispensable in the redox process of the heteropolyanions in a 1 mol/L H2SO4 solution and played a key role in the abnormal change of the resonant frequency.Such a change was attributed to different packing densities derived by means of differently immobilized methods.
基金ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China （No.9732011CB606200 and No.81330031） and Fundamentat Research Funds for the Central Universities （No.SWJTU11CX054）. The authors gratefully acknowledge assistance of Mr. Hai-bei Liu at Qsense company for consulting.
文摘The adsorption of fibrinogen can be used as a quick indicator of surface haemocompatibility because of its prominent role in coagulation and platelet adhesion. In this work the molecular interaction between fibrinogen and a modified titanium oxide surface/platelet has been studied by quartz crystal microbalanee with dissipation （QCM-D） in situ. In order to further characterize the conformation of adsorbed fibrinogen, αC and γ-chain antibody were used to check the orientation and denaturation of fibrinogen on solid surface. QCM-D investiga- tions revealed the fibrinogen have the trend to adsorb on hydropllilic surface in a side-on orientation by positively charged αC domains, which would reduce the exposure of platelet bonding site on γ chain and enable less platelet adhesion and be activated. These obser- vations suggest that certain conformations of adsorbed fibrinogen are less platelet adhesive than others, which opens a possibility for creating a non-platelet adhesive substrates.
基金This work was supported by the National Natural Science Foundation of China （No.20474060）.
文摘The effect of salt concentration on layer-by-layer deposition of poly（sodium 4-styrene sulfonate） （PSSS）/poly（vinylbenzyl trimethylammonium chloride） （PVTC） was investigated by use of quartz crystal microbalance with dissipation （QCM-D）. The changes in frequency and dissipation demonstrate that the addition of NaC1 leads the thickness of PSSS/PVTC multilayer to increase. The deposition of PSSS/PVTC is dominated by surface charge overcompensation level at lower salt concentrations. However, it is mainly determined by the interpenetration of polyelectrolytes at a higher salt concentration, as reflected in the oscillation of dissipation change.
基金supported by the National Natural Science Foundation of China(Grant No.61672094)
文摘The quartz crystal microbalance（QCM） is an important tool that can sense nanogram changes in mass. The hybrid temperature effect on a QCM resonator in aqueous solutions leads to unconvincing detection results. Control of the temperature effect is one of the keys when using the QCM for high precision measurements. Based on the Sauerbrey＇s and Kanazawa＇s theories, we proposed a method for enhancing the accuracy of the QCM measurement, which takes into account not only the thermal variations of viscosity and density but also the thermal behavior of the QCM resonator. We presented an improved Sauerbrey equation that can be used to effectively compensate the drift of the QCM resonator. These results will play a significant role when applying the QCM at the room temperature.
基金supported by the National Natural Science Foundation of China(31972147)Project of Tianjin Science and Technology Plan(19PTSYJC00050)+1 种基金the Open Project Program of State Key Laboratory of Food Nutrition and Safety,Tianjin University of Science and Technology(SKLFNS-KF-202011)Project program of Key Laboratory of Food Nutrition and Safety,Ministry of Education,Tianjin Key Laboratory of Food Nutrition and Safety,China(JYB202002)。
文摘In this study,a label-free,portable and reproducible immunochip based on quartz crystal microbalance(QCM)was developed for the qualitative detection ofβ-lactoglobulin(β-LG),an allergen,in milk products.Experimental parameters in the fabrication and regeneration procedure such as pH of the coupling microenvironment,amount of anti-β-LG antibody and regeneration reagent were optimized in detail.Under optimal conditions,the proposed QCM immunochip exhibited good recognition of β-LG,with a calibration curve of ΔF=12.877 C_(β-LG)^(0.4809)(R^(2)=0.9982)and limit of detection of 0.04μg/mL.Additionally,this portable QCM immunochip had good stability,high specificity,and no obvious cross-reaction to three other milk proteins(α-casein,α-lactalbumin,and lactoferrin).It could compete a qualitative measurement within5 min,and could be reused at least ten times.In the β-LG analysis of actual milk samples,the developed QCM immunochip yielded reliable and accurate results,which correlated strongly with those from the standard HPLC method(R^(2)=0.9969).Thus,the portable,stable,and reproducible QCM immunochip developed in this study allowed the rapid,cost-effectively and sensitively measure theβ-LG in milk products.
文摘The gravimetric analysis of electrodeposited nickel is demonstrated using electrochemical quartz crystal microbalance (EQCM) where the nickel coatings come from a solution of the metal chloride salt separately in either a1choline chloride: 2 ethylene glycol (ethaline) or 1 choline chloride: 2 urea (reline) based ionic liquid. The possibility of adapting the Quartz Crystal Microbalance EQCM (which measures the mass attached to the electrode) to probe kinetics of electrochemically-driven solid state phase transformations has been explored in a Ni electrodeposition in absence and presence of complexing agents ethylene diamine en and acetylacetonate acac from both electrolytes ethaline and reline. The study shows that the current efficiency and the rate of deposition of nickel coatings obtained from ethaline and reline baths in absence of brighteners en and acac are different, and the addition of en and acac to both ionic liquid solutions results in a significant decrease current. And the associated growth rate will also be decreased, suggesting that the en acac stops the formation and growth of Ni nuclei. This suggests that the mechanism of growth is changed.
文摘Nanoparticles are playing an increasingly important role in the development of biosensors. The sensitivity and performance of biosensors are being improved by using Nanoparticles for their construction. The use of these Nanoparticles has allowed the introduction of many new signal transduction technologies in biosensors. In this report, a comprehensive review of application of nanoparticles in Quartz Crystal Microbalance biosensors is presented. The main advantages of QCM in sensing fields include high sensitivity, high stability, fast response and low cost. In addition, it provides label-free detection capability for bio-sensing applications. Firstly, basic QCM’s design and characterization are described. Next, QCM biosensors based on modification of quartz substrate structure and their applications are digested. Nanoparticles and their utilizationin analysis are then illustrated. These include Nanoparticles in bio applications that cover Nanoparticles in Quartz Crystal Microbalance biosensors.
文摘We have investigated the interactions between phospholipid monolayers and volatile anest-hatics. Two monolayers (dihexadecyl phosphate (DHP) and dipalmitoyl phosphatidyl choline (DPPC) and two anesthetics (halothane and enflurane) were used to observe these interac-tions using a highly sensitive quartz crystal microbalance (HS-QCM). The concentration of each anesthetic in aqueous solution was kept at 4 mM. The frequency of QCM showed no change when halothane was added to the DHP monolayer, however, it responded and de-creased when interaction occurred with DPPC monolayer. In case of enflurane addition the frequency decreased in both the monolayers of DHP and DPPC. The frequency change followed the following order of monolayer-anesthetic interactions: DHP-halothane <DPPC-halothane <DHP-enflurane <DPPC-enflurane. These re-sults showed that the response of anesthetics to the monolayers i.e. the physisorption not only depends on the anesthetic structure, the type of anesthetic hydrate formed, but also the hydrophilic polar group structure of the monolayer or the monolayer/water interface had an important role in physisorption.
文摘We are developing methods to quantify antibody interactions that include a quartz crystal microbalance (QCM) system to measure, on a molecular basis, the interaction of p53 and anti-p53 antibodies. Previously, as a model system, we developed a measurement device consisting of p53 protein (human wild type), characterized by mass spectroscopy and immobilized at various concentrations on a glass slide. The device is designed as a control to be used with immunohistochemical (IHC) assays that incorporate commercially available anti-p53 antibodies and probes. In the current study, p53 protein is covalently immobilized on a silicon dioxide-coated quartz crystal and the resonance frequency shift is followed in-situ. The functionalized sensor is then incubated with the anti-p53 antibody, which provides a direct gravimetric measure of the antibody-antigen binding. This previously described method allows the comparison of the surface immobilized protein concentrations with estimates obtained by fluorescence measurement. The p53 functionalized QCM system offers an independent measure of surface immobilized protein concentration and is essential in development of our IHC calibration prototypes. These results provide a benchmark for comparing antibody systems that may be used in developing other molecular diagnostic assays such as immunocytochemical analysis and the detection of biomarker proteins in blood and urine.
