Temporary plugging and diversion fracturing(TPDF)is widely used to promote the uniform and complex distribution of multi-clustered hydraulic fractures(HFs)in a horizontal well of the unconventional formations.However,...Temporary plugging and diversion fracturing(TPDF)is widely used to promote the uniform and complex distribution of multi-clustered hydraulic fractures(HFs)in a horizontal well of the unconventional formations.However,the migration behavior of temporary plugging agent(TPA),as a function of the concentration and particle size of TPA and cluster-perforation numbers,etc.,determining the effectiveness of this technique,remains unclear.Therefore,this study conducted innovatively a series of TPDF simulation experiments on transparent polymethyl methacrylate(PMMA)specimens(cubic block of 30 cm×30 cm×30 cm)to explore visually the migration behavior of TPA in multi-clustered HFs in a horizontal well.A laboratory hydraulic sandblasting perforation completion technique was implemented to simulate the multi-cluster perforations.All the distributions of wellbore,perforations,HFs,and TPA can be seen clearly inside the PMMA specimen post the experiment.The results show that there are four characteristic plugging positions for the TPA:mouth of HF,middle of HF,tip of HF,and the intersection of HFs.Small particle size TPA tends to migrate to the fracture tip for plugging,while large particle size TPA tends to plug at the fracture mouth.The migration of the TPA is influenced obviously by the morphology of the fracture wall.A smooth fracture wall is conducive to the migration of the TPA to the far end of HFs,but not conducive to generating the plugging zone and HF diversion.In contrast,a"leaf vein"fracture of rough wall is conducive to generating the plugging layer and the diversion of HFs,but not conducive to the migration of the TPA to the far end of HFs.The migration ability of TPA in a"shell"pattern is intermediate between the two above cases.Increasing TPA concentration can encourage TPA to migrate more quickly to the characteristic plugging position,and thereby to promote the creation of effective plugging and subsequently the multi-stage diversion of the HFs.Nevertheless,excessive concentration may cause the TPA to settle prematurely,affecting the propagation of the HFs to the far end.Increasing the number of clusters to a certain extent can encourage TPA to migrate into the HFs and form plugging,and promote the diversion.An evaluation system for the migration ability of granular TPA has been established,and it was calculated that when there is no plugging expectation target,the comprehensive migration ability of small particle size TPA is stronger than that of large particle size TPA.This research provides theoretical foundation for the optimization of temporary plugging parameters.展开更多
Emulsifier-free poly（methyl methacrylate-styrene） [P（MMA-St）] nanospheres with an average particle size of 100 nm were synthesized in an isopropyl alcoholwater medium by a solvothermal method. Then, through radica...Emulsifier-free poly（methyl methacrylate-styrene） [P（MMA-St）] nanospheres with an average particle size of 100 nm were synthesized in an isopropyl alcoholwater medium by a solvothermal method. Then, through radical graft copolymerization of thermo-sensitive mono- mer N-isopropylacrylamide （NIPAm） and hydrophilic monomer acrylic acid （AA） onto the surface of P（MMA- St） nanospheres at 80 ℃, a series of thermo-sensitive polymer nanospheres, named SD-SEAL with different lower critical solution temperatures （LCST）, were prepared by adjusting the mole ratio of NIPAm to AA. The products were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, thermogravimetric analysis, particle size distribution, and specific surface area analysis. The temperature-sensitive behavior was studied by light transmittance tests, while the sealing performance was investigated by pressure transmission tests with Lungmachi Formation shales. The experimental results showed that the synthesized nanoparticles are sensitive to temperature and had apparent LCST values which increased with an increase in hydrophilic monomer AA. When the temperature was higher than its LCST value, SD- SEAL played a dual role of physical plugging and chemical inhibition, slowed down pressure transmission, and reduced shale permeability remarkably. The plugged layer of shale was changed to being hydrophobic, which greatly improved the shale stability展开更多
Temporary plugging agent(TPA)is widely used in many fields of petroleum reservoir drilling and production,such as temporary plugging while drilling and petroleum well stimulation by diverting in acidizing or fracturin...Temporary plugging agent(TPA)is widely used in many fields of petroleum reservoir drilling and production,such as temporary plugging while drilling and petroleum well stimulation by diverting in acidizing or fracturing operations.The commonly used TPA mainly includes hard particles,fibers,gels,and composite systems.However,current particles have many limitations in applications,such as insufficient plugging strength and slow degradation rate.In this paper,a degradable pre-formed particle gel(DPPG)was developed.Experimental results show that the DPPG has an excellent static swelling effect and self-degradation performance.With a decrease in the concentration of total monomers or cross-linker,the swelling volume of the synthesized DPPG gradually increases.However,the entire self-degradation time gradually decreases.The increase in 2-acrylamide-2-methylpropanesulfonic acid(AMPS)in the DPPG composition can significantly increase its swelling ratio and shorten the self-degradation time.Moreover,DPPG has excellent high-temperature resistance(150°C)and high-salinity resistance(200,000 mg/L NaCl).Core displacement results show that the DPPG has a perfect plugging effect in the porous media(the plugging pressure gradient was as high as 21.12 MPa),and the damage to the formation after degradation is incredibly minor.Therefore,the DPPG can be used as an up-and-coming TPA in oil fields.展开更多
The development of unconventional petroleum resources has gradually become an important succession for increasing oil production.However,the related engineers and researchers are paying more and more attention to the ...The development of unconventional petroleum resources has gradually become an important succession for increasing oil production.However,the related engineers and researchers are paying more and more attention to the application of temporary plugging agents(TPAs)for their efficient development.TPAs can expand the stimulated reservoir volume(SRV)and facilitate the flow of oil and gas to the bottom of the well.Particle-gels used as temporary plugging agents have the characteristics of the simple injection process,good deformation,high plugging strength,and complete self-degradation performance,which have been widely applied in recent years.In this paper,five samples of DPPG polymerized by different molecular weights of cross-linking agents were prepared.In addition,infrared spectroscopy analysis,differential calorimetry scanning(DSC)analysis,static particle gel swelling and degradation performance evaluation experiments,and dynamic temporary plugging performance experiments in cores were conducted at 34°C.Results show that as the molecular weight of the cross-linking agent(at 0.01 g)in the DPPG molecule decreased from 1,000 to 200 Da,the fewer cross-linking sites of DPPG,the looser the microscopic three-dimensional mesh structure formed.The swelling ratio increased from 7 to 33 times.However,the complete degradation time increased from 40 to 210 min.Moreover,the DSC results confirmed that the higher the molecular weight of the cross-linking agent,the worse is chemical stability and the more prone it to self-degradation.DPPG samples had good temporary plugging performance in reservoir cores.DPPGs prepared by the cross-linking agent with smaller molecular weight has a stronger swelling ratio,higher gel strength,and greater plugging strength in the core permeabilities.Moreover,the degraded DPPG is less damaging to the cores.However,their slower degradation rates take a slightly longer times to reach complete degradation.The results of this paper can provide new ideas and a theoretical basis for the development of particle gel-type temporary plugging agents(TPA)with controllable degradation time in low-temperature reservoirs.It can help to expand the application range of existing DPPG reservoir conditions.展开更多
This paper describes a series of plugging agents which have been developed these years by the authors. The features of these agents can bestated as: (1) Stopping losses without stopping drilling; (2) High ratio of suc...This paper describes a series of plugging agents which have been developed these years by the authors. The features of these agents can bestated as: (1) Stopping losses without stopping drilling; (2) High ratio of success; (3) Improving fluids properties; (4) Suiting to many types of losses, even large cracks and caves; (5) Perfect efficiency in different conditions of pollution such as calcium, salt pollution and high temperature; (6) Sufficient resources of raw materials, nopoison, noharm, no pollution to the environment; (7) Convenience in use; (8) Lower cost. The properties, mechanisms and applications of these agents are also described in this paper.展开更多
Aimed at the disadvantages of secondary damage to oil layers caused by the conventional bull-heading water control technique, a thermo-sensitive temporary plugging agent for water control was synthesized by water solu...Aimed at the disadvantages of secondary damage to oil layers caused by the conventional bull-heading water control technique, a thermo-sensitive temporary plugging agent for water control was synthesized by water solution polymerization and applied in the field with a new secondary temporary plugging technique. The optimization and performance evaluation of thermo-sensitive temporary plugging agent were carried out through laboratory experiments. The optimized formula is as follows:(6%-8%) acrylamide +(0.08%-0.12%) ammonium persulfate +(1.5%-2.0%) sepiolite +(0.5%-0.8%) polyethylene glycol diacrylate. The thermo-sensitive temporary plugging agent is suitable for formation temperatures of 70-90 ?C, it has high temporary plugging strength(5-40 k Pa), controllable degradation time(1-15 d), the apparent viscosity after degradation of less than 100 m Pa?S and the permeability recovery value of simulated cores of more than 95%. Based on the research results, secondary temporary plugging technique was used in a horizontal well in the Jidong Oilfield. After treatment, the well saw a drop of water cut to 27%, and now it has a water cut of 67%, its daily increased oil production was 4.8 t, and the cumulative oil increment was 750 t, demonstrating that the technique worked well in controlling water production and increasing oil production.展开更多
The paper overviews the research and application of silicate plugging agent, according to the different mechanisms and application forms, the plugging agent is divided into silicate gel, silicate precipitation, silica...The paper overviews the research and application of silicate plugging agent, according to the different mechanisms and application forms, the plugging agent is divided into silicate gel, silicate precipitation, silicate/polymer, silicate/surfactant, silicate gel/foam and so on. This paper chiefly introduces the conception, mechanism and development tendency of the different systems mentioned above. The development tendency manifests as fully utilize personal properties and cooperate with other plugging agents or technologies, including the study of reaction mechanism, combination of plugging agent, grasping water flood timing, developing deep profile control and water shutoff technology, combining with other measures (chemicals huff and puff), in order to play the role of such blocking agents, further enhance oil recovery.展开更多
The hydration products and microstructure of class G oil well cement and a newly developed plugging agent （YLD） slurries cured in the simulated temperature and pressure environment, which was of similar temperature ...The hydration products and microstructure of class G oil well cement and a newly developed plugging agent （YLD） slurries cured in the simulated temperature and pressure environment, which was of similar temperature and pressure with those at the bottom of oil well in a normal depth, were investigated using XRD, TG and SEM. Severe leakage is confirmed at the interface between hardened slurries and steel tube during the dynamically curing process, which induces the quick loss of cementing property of slurries. This should be the dominating cause of degradation of class G oil well cement slurry. A secondary hydration process can take place at the eroded interface of hardened YLD plugging agent slurry. Newly formed C-S-H gel has a self-healing effect to repair the damaged interface, which unceasingly maintains the cementing property of the YLD plugging agent slurry. Therefore, the effective using period of YLD plugging agent can be prolonged.展开更多
After steam discharge in heavy oil reservoirs,the distribution of temperature,pressure,and permeability in different wells becomes irregular.Flow channels can easily be produced,which affect the sweep efficiency of th...After steam discharge in heavy oil reservoirs,the distribution of temperature,pressure,and permeability in different wells becomes irregular.Flow channels can easily be produced,which affect the sweep efficiency of the oil displacement.Previous studies have shown that the salting-out plugging method can effectively block these channels in high-temperature reservoirs,improve the suction profile,and increase oil production.In the present study,the optimal dosage of the plugging agent is determined taking into account connection transmissibility and inter-well volumes.Together with the connectivity model,a water flooding simulation model is introduced.Moreover,a non-gradient stochastic disturbance algorithm is used to obtain the optimal plugging agent dosage,which provides the basis for the high-temperature salting-out plugging agent adjustment in the field.展开更多
In this paper, to solve the problems of low water absorption and weak pressure bearing capacity of current plugging materials, acrylic acid (AA), acrylamide (AM), and sodium allyl sulfonate (SAS) are used as monomers,...In this paper, to solve the problems of low water absorption and weak pressure bearing capacity of current plugging materials, acrylic acid (AA), acrylamide (AM), and sodium allyl sulfonate (SAS) are used as monomers, and soluble starch is used as grafting. Material, the use of free radical aqueous solution method to synthesize the plugging agent SWL-1 with good water absorption and strong salt resistance. The monomer ratio is set as n (AA):n (AM):n (SAS) = 5:2:1, the experimental synthesis temperature is 70°C, and the orthogonal experiment is used to determine the experimental synthesis conditions as AA neutralization degree 80%, The amount of initiator is 0.60%, the amount of crosslinking agent is 0.50%, the ratio of monomer to starch is 7:1, and the amount of calcium carbonate is 13%. The comprehensive evaluation of the performance of the plugging agent SWL-1 shows that the water absorption performance at 60°C is the best 268.78 g/g, and the water absorption performance in 8% NaCl, 0.9% CaCl<sub>2</sub> and composite brine is 21.5 g/g, 12.5 g/g and 24.9 g/g, indicating good resistance to sodium and calcium, the water retention rate is still higher than 30% after 15 days at 160°C. The sand bed plugging test found that the maximum pressure of SWL-1 was 7 MPa, and the crack plugging test found that when the crack width was 1 mm, 2 mm, and 3 mm, the maximum compressive strength of SWL-1 was 10 MPa. The acid solubility test showed that the maximum pressure was 10 MPa. The highest rate is 86.38%.展开更多
In order to improve the plugging and anti-collapse performance of water-based drilling fluid,a polymer film-forming plugging agent LWFD is synthesized by emulsion polymerization.The effect of the agent on rheology,API...In order to improve the plugging and anti-collapse performance of water-based drilling fluid,a polymer film-forming plugging agent LWFD is synthesized by emulsion polymerization.The effect of the agent on rheology,API filtration loss,lubricity and film plugging of polymer drilling fluid and cationic drilling fluid is evaluated in laboratory.The experimental results show that the agent has little effect on the rheology and filtration loss of polymer drilling fluid and cationic drilling fluid,and can improve the lubricity of drilling fluid.The synthesized polymer film-forming plugging agent LWFD has good plugging properties for sand discs with different permeabilities,and the agent can effectively improve the film-forming plugging and temperature resistance of drilling fluid when combined with the inorganic nano-plugging agent NMFD.The high performance polymer drilling fluid formed by introducing polymer film-forming plugging agent LWFD and inorganic nano-plugging agent NMFD into polymer drilling fluid has comparable performance as Halliburton’s SHALEDRIL high performance drilling fluid,which can meet the requirements of on-site drilling and has application value.展开更多
This study conducted temporary plugging and diversion fracturing(TPDF)experiments using a true triaxial fracturing simulation system within a laboratory setting that replicated a lab-based horizontal well completion w...This study conducted temporary plugging and diversion fracturing(TPDF)experiments using a true triaxial fracturing simulation system within a laboratory setting that replicated a lab-based horizontal well completion with multi-cluster sand jetting perforation.The effects of temporary plugging agent(TPA)particle size,TPA concentration,single-cluster perforation number and cluster number on plugging pressure,multi-fracture diversion pattern and distribution of TPAs were investigated.A combination of TPAs with small particle sizes within the fracture and large particle sizes within the segment is conducive to increasing the plugging pressure and promoting the diversion of multi-fractures.The addition of fibers can quickly achieve ultra-high pressure,but it may lead to longitudinal fractures extending along the wellbore.The temporary plugging peak pressure increases with an increase in the concentration of the TPA,reaching a peak at a certain concentration,and further increases do not significantly improve the temporary plugging peak pressure.The breaking pressure and temporary plugging peak pressure show a decreasing trend with an increase in single-cluster perforation number.A lower number of single-cluster perforations is beneficial for increasing the breaking pressure and temporary plugging peak pressure,and it has a more significant control on the propagation of multi-cluster fractures.A lower number of clusters is not conducive to increasing the total number and complexity of artificial fractures,while a higher number of clusters makes it difficult to achieve effective plugging.The TPAs within the fracture is mainly concentrated in the complex fracture areas,especially at the intersections of fractures.Meanwhile,the TPAs within the segment are primarily distributed near the perforation cluster apertures which initiated complex fractures.展开更多
In view of the shortcomings of poor temperature resistance, poor pumpability and poor pressure-bearing capacity of commonly used gel plugging materials, polyacrylamide (HPAM) and N,N-methylene bisacrylamide (BIS) were...In view of the shortcomings of poor temperature resistance, poor pumpability and poor pressure-bearing capacity of commonly used gel plugging materials, polyacrylamide (HPAM) and N,N-methylene bisacrylamide (BIS) were selected for crosslinking and compounding to make a new type of gel plugging material with high temperature and pressure resistance. The compressive strength and yield stress were measured by inverted observation method to evaluate the gel strength. The anti-temperature, anti-pressure, anti-dilution and gel-breaking properties of the gel were evaluated. Finally, 71 type high temperature and high pressure water loss instrument and high temperature and high pressure filter with slit plate were used to evaluate the plugging capacity of gel plugging agent. The experimental results show that the new gel plugging system between 100°C - 120°C, gelation time can be controlled at about 5 h;it has strong temperature resistance, compression resistance, dilution resistance and gel breaking performance. In the face of permeability and fracture leakage simulation experiments, when the ambient temperature below 120°C, pressure within 5 MPa, the filter loss of gel plugging agent is far less than the market two conventional plugging agent, has excellent plugging performance.展开更多
At present, in the workover operations of old gas wells in the Changqing Gas Field, due to years of exploitation in the production layer, pressure deficits, and general leakage during the well killing, the well must b...At present, in the workover operations of old gas wells in the Changqing Gas Field, due to years of exploitation in the production layer, pressure deficits, and general leakage during the well killing, the well must be plugged before the well can be killed. In particular, the fracture-cavity type fractures of the lower paleocarbonate reservoirs have serious leakage. Traditional plugging materials and traditional plugging materials and methods have some limitations in dealing with leakage problems. Therefore, a composite plugging system using polymer solution as the base carrier fluid, multi-particle size rigid particles, expandable particles and modified fibers is developed. Its formula is: water + 2% polyacrylamide + 0.1% N, N-methylene bisacrylamide polymer gel is the base carrier fluid;the formulation of the particle plugging agent was continuously optimized through the CDL-II high temperature and high pressure dynamic and static plugging ability to plug the core. The final formulation of the plugging agent is: 1) 20% rigid particles (5 mm, 1 mm, 0.5 mm CCP-3 ratio 4:2:1) + 1% 3 mm expanded particles SMK-1 + 1% 1 ~ 2 mm fiber SRXW-10;2) 20% rigid particles (3 mm, 0.1 mm, 0.05 mm CCP-3 ratio 3:2:1) + 1% 3 mm expanded particles SMK-1 + 1% 1 ~ 2 mm fiber SRXW-10. The water swelling multiples of the granular plugging agent in salt water are all above 7 times, which meets the requirements of leak-proof plugging operations under high salinity;3% HCl is selected as the gel breaker, and the plugging system has a gel breaking rate of 95%;through the water plugging and profile control experimental system, the sand-filled pipe is used to simulate the plugging effect under high temperature and high pressure, and the plugging system can be sealed for 5 days at a high temperature of 110°C and a high pressure of 20 MPa to achieve a good plugging of the formation. It is expected that the developed plugging system has a good application prospect in future workover operations.展开更多
At present, the oil and water wells in Liaohe Oilfield have entered the middle and later stages of development. The pressure of the oil and water wells has decreased year by year and the contradiction between injectio...At present, the oil and water wells in Liaohe Oilfield have entered the middle and later stages of development. The pressure of the oil and water wells has decreased year by year and the contradiction between injection and production has become increasingly prominent. In order to maximize its recovery, various new processes and technologies have been widely applied in different oilfields. The loss of workover fluid during workover operation not only increases the dosage of workover fluid, but also causes more serious pollution to the oil layer (formation). Affect oil production after workover operation.展开更多
基金supported by the National Natural Science Foundation of China Joint Fund for Enterprise Innovation and Development,Enrichment Mechanism and Stereoscopic Development of Shale Oil in Continental Rift Basins(No.U24B6002).
文摘Temporary plugging and diversion fracturing(TPDF)is widely used to promote the uniform and complex distribution of multi-clustered hydraulic fractures(HFs)in a horizontal well of the unconventional formations.However,the migration behavior of temporary plugging agent(TPA),as a function of the concentration and particle size of TPA and cluster-perforation numbers,etc.,determining the effectiveness of this technique,remains unclear.Therefore,this study conducted innovatively a series of TPDF simulation experiments on transparent polymethyl methacrylate(PMMA)specimens(cubic block of 30 cm×30 cm×30 cm)to explore visually the migration behavior of TPA in multi-clustered HFs in a horizontal well.A laboratory hydraulic sandblasting perforation completion technique was implemented to simulate the multi-cluster perforations.All the distributions of wellbore,perforations,HFs,and TPA can be seen clearly inside the PMMA specimen post the experiment.The results show that there are four characteristic plugging positions for the TPA:mouth of HF,middle of HF,tip of HF,and the intersection of HFs.Small particle size TPA tends to migrate to the fracture tip for plugging,while large particle size TPA tends to plug at the fracture mouth.The migration of the TPA is influenced obviously by the morphology of the fracture wall.A smooth fracture wall is conducive to the migration of the TPA to the far end of HFs,but not conducive to generating the plugging zone and HF diversion.In contrast,a"leaf vein"fracture of rough wall is conducive to generating the plugging layer and the diversion of HFs,but not conducive to the migration of the TPA to the far end of HFs.The migration ability of TPA in a"shell"pattern is intermediate between the two above cases.Increasing TPA concentration can encourage TPA to migrate more quickly to the characteristic plugging position,and thereby to promote the creation of effective plugging and subsequently the multi-stage diversion of the HFs.Nevertheless,excessive concentration may cause the TPA to settle prematurely,affecting the propagation of the HFs to the far end.Increasing the number of clusters to a certain extent can encourage TPA to migrate into the HFs and form plugging,and promote the diversion.An evaluation system for the migration ability of granular TPA has been established,and it was calculated that when there is no plugging expectation target,the comprehensive migration ability of small particle size TPA is stronger than that of large particle size TPA.This research provides theoretical foundation for the optimization of temporary plugging parameters.
基金financial support from the National Science Foundation of China (Nos. 51374233, 51474235)the Postdoctoral Innovative Project Foundation of Shandong Province (No. 201602027)+2 种基金the Qingdao Postdoctoral Applied Research Project (No. 2015242)the Fundamental Research Funds for the Central Universities (No. 15CX06021A)the Graduate Student Innovation Project from China University of Petroleum (East China) (No. YCX2015011)
文摘Emulsifier-free poly（methyl methacrylate-styrene） [P（MMA-St）] nanospheres with an average particle size of 100 nm were synthesized in an isopropyl alcoholwater medium by a solvothermal method. Then, through radical graft copolymerization of thermo-sensitive mono- mer N-isopropylacrylamide （NIPAm） and hydrophilic monomer acrylic acid （AA） onto the surface of P（MMA- St） nanospheres at 80 ℃, a series of thermo-sensitive polymer nanospheres, named SD-SEAL with different lower critical solution temperatures （LCST）, were prepared by adjusting the mole ratio of NIPAm to AA. The products were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, thermogravimetric analysis, particle size distribution, and specific surface area analysis. The temperature-sensitive behavior was studied by light transmittance tests, while the sealing performance was investigated by pressure transmission tests with Lungmachi Formation shales. The experimental results showed that the synthesized nanoparticles are sensitive to temperature and had apparent LCST values which increased with an increase in hydrophilic monomer AA. When the temperature was higher than its LCST value, SD- SEAL played a dual role of physical plugging and chemical inhibition, slowed down pressure transmission, and reduced shale permeability remarkably. The plugged layer of shale was changed to being hydrophobic, which greatly improved the shale stability
基金This work was supported by the Research Foundation of China University of Petroleum-Beijing at Karamay(No.XQZX20200010)the Natural Science Foundation of Xinjiang Uygur Autonomous Region(No.2019D01B57)+3 种基金the University Scientific Research Project of Xinjiang Uygur Autonomous Region(No.XJEDU2019Y067)the Xinjiang Uygur Autonomous Region Innovation Environment Construction Project(No.2019Q025)the Sichuan Province Regional Innovation Cooperation Project(No.2020YFQ0036)the CNPC Strategic Cooperation Science and Technology Project(ZLZX2020-01-04-04)。
文摘Temporary plugging agent(TPA)is widely used in many fields of petroleum reservoir drilling and production,such as temporary plugging while drilling and petroleum well stimulation by diverting in acidizing or fracturing operations.The commonly used TPA mainly includes hard particles,fibers,gels,and composite systems.However,current particles have many limitations in applications,such as insufficient plugging strength and slow degradation rate.In this paper,a degradable pre-formed particle gel(DPPG)was developed.Experimental results show that the DPPG has an excellent static swelling effect and self-degradation performance.With a decrease in the concentration of total monomers or cross-linker,the swelling volume of the synthesized DPPG gradually increases.However,the entire self-degradation time gradually decreases.The increase in 2-acrylamide-2-methylpropanesulfonic acid(AMPS)in the DPPG composition can significantly increase its swelling ratio and shorten the self-degradation time.Moreover,DPPG has excellent high-temperature resistance(150°C)and high-salinity resistance(200,000 mg/L NaCl).Core displacement results show that the DPPG has a perfect plugging effect in the porous media(the plugging pressure gradient was as high as 21.12 MPa),and the damage to the formation after degradation is incredibly minor.Therefore,the DPPG can be used as an up-and-coming TPA in oil fields.
基金supported by the Research Foundation of China University of Petroleum-Beijing at Karamay (No. YJ2018B02002 and XQZX20200010)the Natural Science Foundation of Xinjiang Uygur Autonomous Region (No. 2021D01E23 and 2019D01B57)+3 种基金the University Scientific Research Project of Xinjiang Uygur Autonomous Region (No. XJEDU2019Y067)the Xinjiang Uygur Autonomous Region Innovation Environment Construction Project (No. 2019Q025)the Sichuan Province Regional Innovation Cooperation Project (No. 2020YFQ0036)the CNPC Strategic Cooperation Science and Technology Project (ZLZX2020-01-04-04)
文摘The development of unconventional petroleum resources has gradually become an important succession for increasing oil production.However,the related engineers and researchers are paying more and more attention to the application of temporary plugging agents(TPAs)for their efficient development.TPAs can expand the stimulated reservoir volume(SRV)and facilitate the flow of oil and gas to the bottom of the well.Particle-gels used as temporary plugging agents have the characteristics of the simple injection process,good deformation,high plugging strength,and complete self-degradation performance,which have been widely applied in recent years.In this paper,five samples of DPPG polymerized by different molecular weights of cross-linking agents were prepared.In addition,infrared spectroscopy analysis,differential calorimetry scanning(DSC)analysis,static particle gel swelling and degradation performance evaluation experiments,and dynamic temporary plugging performance experiments in cores were conducted at 34°C.Results show that as the molecular weight of the cross-linking agent(at 0.01 g)in the DPPG molecule decreased from 1,000 to 200 Da,the fewer cross-linking sites of DPPG,the looser the microscopic three-dimensional mesh structure formed.The swelling ratio increased from 7 to 33 times.However,the complete degradation time increased from 40 to 210 min.Moreover,the DSC results confirmed that the higher the molecular weight of the cross-linking agent,the worse is chemical stability and the more prone it to self-degradation.DPPG samples had good temporary plugging performance in reservoir cores.DPPGs prepared by the cross-linking agent with smaller molecular weight has a stronger swelling ratio,higher gel strength,and greater plugging strength in the core permeabilities.Moreover,the degraded DPPG is less damaging to the cores.However,their slower degradation rates take a slightly longer times to reach complete degradation.The results of this paper can provide new ideas and a theoretical basis for the development of particle gel-type temporary plugging agents(TPA)with controllable degradation time in low-temperature reservoirs.It can help to expand the application range of existing DPPG reservoir conditions.
文摘This paper describes a series of plugging agents which have been developed these years by the authors. The features of these agents can bestated as: (1) Stopping losses without stopping drilling; (2) High ratio of success; (3) Improving fluids properties; (4) Suiting to many types of losses, even large cracks and caves; (5) Perfect efficiency in different conditions of pollution such as calcium, salt pollution and high temperature; (6) Sufficient resources of raw materials, nopoison, noharm, no pollution to the environment; (7) Convenience in use; (8) Lower cost. The properties, mechanisms and applications of these agents are also described in this paper.
基金Supported by the National Key Special Science and Technology Project(2016ZX05015-002)PetroChina Key Special Science and Technology Project(2016E-0104)
文摘Aimed at the disadvantages of secondary damage to oil layers caused by the conventional bull-heading water control technique, a thermo-sensitive temporary plugging agent for water control was synthesized by water solution polymerization and applied in the field with a new secondary temporary plugging technique. The optimization and performance evaluation of thermo-sensitive temporary plugging agent were carried out through laboratory experiments. The optimized formula is as follows:(6%-8%) acrylamide +(0.08%-0.12%) ammonium persulfate +(1.5%-2.0%) sepiolite +(0.5%-0.8%) polyethylene glycol diacrylate. The thermo-sensitive temporary plugging agent is suitable for formation temperatures of 70-90 ?C, it has high temporary plugging strength(5-40 k Pa), controllable degradation time(1-15 d), the apparent viscosity after degradation of less than 100 m Pa?S and the permeability recovery value of simulated cores of more than 95%. Based on the research results, secondary temporary plugging technique was used in a horizontal well in the Jidong Oilfield. After treatment, the well saw a drop of water cut to 27%, and now it has a water cut of 67%, its daily increased oil production was 4.8 t, and the cumulative oil increment was 750 t, demonstrating that the technique worked well in controlling water production and increasing oil production.
文摘The paper overviews the research and application of silicate plugging agent, according to the different mechanisms and application forms, the plugging agent is divided into silicate gel, silicate precipitation, silicate/polymer, silicate/surfactant, silicate gel/foam and so on. This paper chiefly introduces the conception, mechanism and development tendency of the different systems mentioned above. The development tendency manifests as fully utilize personal properties and cooperate with other plugging agents or technologies, including the study of reaction mechanism, combination of plugging agent, grasping water flood timing, developing deep profile control and water shutoff technology, combining with other measures (chemicals huff and puff), in order to play the role of such blocking agents, further enhance oil recovery.
文摘The hydration products and microstructure of class G oil well cement and a newly developed plugging agent （YLD） slurries cured in the simulated temperature and pressure environment, which was of similar temperature and pressure with those at the bottom of oil well in a normal depth, were investigated using XRD, TG and SEM. Severe leakage is confirmed at the interface between hardened slurries and steel tube during the dynamically curing process, which induces the quick loss of cementing property of slurries. This should be the dominating cause of degradation of class G oil well cement slurry. A secondary hydration process can take place at the eroded interface of hardened YLD plugging agent slurry. Newly formed C-S-H gel has a self-healing effect to repair the damaged interface, which unceasingly maintains the cementing property of the YLD plugging agent slurry. Therefore, the effective using period of YLD plugging agent can be prolonged.
基金supported by China Postdoctoral Science Foundation(No.2021M702304)Shandong Provincial Natural Science Foundation Youth Fund(No.ZR2021QE260).
文摘After steam discharge in heavy oil reservoirs,the distribution of temperature,pressure,and permeability in different wells becomes irregular.Flow channels can easily be produced,which affect the sweep efficiency of the oil displacement.Previous studies have shown that the salting-out plugging method can effectively block these channels in high-temperature reservoirs,improve the suction profile,and increase oil production.In the present study,the optimal dosage of the plugging agent is determined taking into account connection transmissibility and inter-well volumes.Together with the connectivity model,a water flooding simulation model is introduced.Moreover,a non-gradient stochastic disturbance algorithm is used to obtain the optimal plugging agent dosage,which provides the basis for the high-temperature salting-out plugging agent adjustment in the field.
文摘In this paper, to solve the problems of low water absorption and weak pressure bearing capacity of current plugging materials, acrylic acid (AA), acrylamide (AM), and sodium allyl sulfonate (SAS) are used as monomers, and soluble starch is used as grafting. Material, the use of free radical aqueous solution method to synthesize the plugging agent SWL-1 with good water absorption and strong salt resistance. The monomer ratio is set as n (AA):n (AM):n (SAS) = 5:2:1, the experimental synthesis temperature is 70°C, and the orthogonal experiment is used to determine the experimental synthesis conditions as AA neutralization degree 80%, The amount of initiator is 0.60%, the amount of crosslinking agent is 0.50%, the ratio of monomer to starch is 7:1, and the amount of calcium carbonate is 13%. The comprehensive evaluation of the performance of the plugging agent SWL-1 shows that the water absorption performance at 60°C is the best 268.78 g/g, and the water absorption performance in 8% NaCl, 0.9% CaCl<sub>2</sub> and composite brine is 21.5 g/g, 12.5 g/g and 24.9 g/g, indicating good resistance to sodium and calcium, the water retention rate is still higher than 30% after 15 days at 160°C. The sand bed plugging test found that the maximum pressure of SWL-1 was 7 MPa, and the crack plugging test found that when the crack width was 1 mm, 2 mm, and 3 mm, the maximum compressive strength of SWL-1 was 10 MPa. The acid solubility test showed that the maximum pressure was 10 MPa. The highest rate is 86.38%.
基金Project of National Natural Science Foundation of China“Research on Shale Wellbore Stability and Fracture Mechanism under Shale Gas Development Conditions”(51174036).
文摘In order to improve the plugging and anti-collapse performance of water-based drilling fluid,a polymer film-forming plugging agent LWFD is synthesized by emulsion polymerization.The effect of the agent on rheology,API filtration loss,lubricity and film plugging of polymer drilling fluid and cationic drilling fluid is evaluated in laboratory.The experimental results show that the agent has little effect on the rheology and filtration loss of polymer drilling fluid and cationic drilling fluid,and can improve the lubricity of drilling fluid.The synthesized polymer film-forming plugging agent LWFD has good plugging properties for sand discs with different permeabilities,and the agent can effectively improve the film-forming plugging and temperature resistance of drilling fluid when combined with the inorganic nano-plugging agent NMFD.The high performance polymer drilling fluid formed by introducing polymer film-forming plugging agent LWFD and inorganic nano-plugging agent NMFD into polymer drilling fluid has comparable performance as Halliburton’s SHALEDRIL high performance drilling fluid,which can meet the requirements of on-site drilling and has application value.
基金Supported by the National Natural Science Foundation of China(51974332).
文摘This study conducted temporary plugging and diversion fracturing(TPDF)experiments using a true triaxial fracturing simulation system within a laboratory setting that replicated a lab-based horizontal well completion with multi-cluster sand jetting perforation.The effects of temporary plugging agent(TPA)particle size,TPA concentration,single-cluster perforation number and cluster number on plugging pressure,multi-fracture diversion pattern and distribution of TPAs were investigated.A combination of TPAs with small particle sizes within the fracture and large particle sizes within the segment is conducive to increasing the plugging pressure and promoting the diversion of multi-fractures.The addition of fibers can quickly achieve ultra-high pressure,but it may lead to longitudinal fractures extending along the wellbore.The temporary plugging peak pressure increases with an increase in the concentration of the TPA,reaching a peak at a certain concentration,and further increases do not significantly improve the temporary plugging peak pressure.The breaking pressure and temporary plugging peak pressure show a decreasing trend with an increase in single-cluster perforation number.A lower number of single-cluster perforations is beneficial for increasing the breaking pressure and temporary plugging peak pressure,and it has a more significant control on the propagation of multi-cluster fractures.A lower number of clusters is not conducive to increasing the total number and complexity of artificial fractures,while a higher number of clusters makes it difficult to achieve effective plugging.The TPAs within the fracture is mainly concentrated in the complex fracture areas,especially at the intersections of fractures.Meanwhile,the TPAs within the segment are primarily distributed near the perforation cluster apertures which initiated complex fractures.
文摘In view of the shortcomings of poor temperature resistance, poor pumpability and poor pressure-bearing capacity of commonly used gel plugging materials, polyacrylamide (HPAM) and N,N-methylene bisacrylamide (BIS) were selected for crosslinking and compounding to make a new type of gel plugging material with high temperature and pressure resistance. The compressive strength and yield stress were measured by inverted observation method to evaluate the gel strength. The anti-temperature, anti-pressure, anti-dilution and gel-breaking properties of the gel were evaluated. Finally, 71 type high temperature and high pressure water loss instrument and high temperature and high pressure filter with slit plate were used to evaluate the plugging capacity of gel plugging agent. The experimental results show that the new gel plugging system between 100°C - 120°C, gelation time can be controlled at about 5 h;it has strong temperature resistance, compression resistance, dilution resistance and gel breaking performance. In the face of permeability and fracture leakage simulation experiments, when the ambient temperature below 120°C, pressure within 5 MPa, the filter loss of gel plugging agent is far less than the market two conventional plugging agent, has excellent plugging performance.
文摘At present, in the workover operations of old gas wells in the Changqing Gas Field, due to years of exploitation in the production layer, pressure deficits, and general leakage during the well killing, the well must be plugged before the well can be killed. In particular, the fracture-cavity type fractures of the lower paleocarbonate reservoirs have serious leakage. Traditional plugging materials and traditional plugging materials and methods have some limitations in dealing with leakage problems. Therefore, a composite plugging system using polymer solution as the base carrier fluid, multi-particle size rigid particles, expandable particles and modified fibers is developed. Its formula is: water + 2% polyacrylamide + 0.1% N, N-methylene bisacrylamide polymer gel is the base carrier fluid;the formulation of the particle plugging agent was continuously optimized through the CDL-II high temperature and high pressure dynamic and static plugging ability to plug the core. The final formulation of the plugging agent is: 1) 20% rigid particles (5 mm, 1 mm, 0.5 mm CCP-3 ratio 4:2:1) + 1% 3 mm expanded particles SMK-1 + 1% 1 ~ 2 mm fiber SRXW-10;2) 20% rigid particles (3 mm, 0.1 mm, 0.05 mm CCP-3 ratio 3:2:1) + 1% 3 mm expanded particles SMK-1 + 1% 1 ~ 2 mm fiber SRXW-10. The water swelling multiples of the granular plugging agent in salt water are all above 7 times, which meets the requirements of leak-proof plugging operations under high salinity;3% HCl is selected as the gel breaker, and the plugging system has a gel breaking rate of 95%;through the water plugging and profile control experimental system, the sand-filled pipe is used to simulate the plugging effect under high temperature and high pressure, and the plugging system can be sealed for 5 days at a high temperature of 110°C and a high pressure of 20 MPa to achieve a good plugging of the formation. It is expected that the developed plugging system has a good application prospect in future workover operations.
文摘At present, the oil and water wells in Liaohe Oilfield have entered the middle and later stages of development. The pressure of the oil and water wells has decreased year by year and the contradiction between injection and production has become increasingly prominent. In order to maximize its recovery, various new processes and technologies have been widely applied in different oilfields. The loss of workover fluid during workover operation not only increases the dosage of workover fluid, but also causes more serious pollution to the oil layer (formation). Affect oil production after workover operation.
