It is economical to perform methane and carbon dioxide reforming(DRM)under industrially relevant high-pressure conditions,but the harsh operation condition poses a grand challenge for coke-resistant catalyst design.He...It is economical to perform methane and carbon dioxide reforming(DRM)under industrially relevant high-pressure conditions,but the harsh operation condition poses a grand challenge for coke-resistant catalyst design.Here,we propose to boost the coke-tolerance of Co catalyst by applying a contact potential introduced by immiscible Ag clusters.We demonstrate that Co clusters separated by neighboring Ag on Yttria-stabilized zirconia(YSZ)support can serve as a coke-and sintering-resistant DRM catalyst under diluent gas-free,stoichiometric CH_(4) and CO_(2) feeding,1123 K and 20 bar.Since immiscible metals are ubiquitous and metal contact influences surface work function in general,this new design concept may have general implications for tailoring catalytic properties of metals.展开更多
In the past decade,dry reforming of methane(DRM)has garnered increasing interest as it converts CH_(4)and CO_(2),two typical greenhouse gases,into synthesis gas(H_(2)and CO)for the production of high-value-added chemi...In the past decade,dry reforming of methane(DRM)has garnered increasing interest as it converts CH_(4)and CO_(2),two typical greenhouse gases,into synthesis gas(H_(2)and CO)for the production of high-value-added chemicals and fuels.Nickel-based DRM catalysts,renowned for their high activity and low cost,however,encounter challenges such as severe deactivation from sintering and carbon deposition.Herein,a surrounded NiO@NiAlO precursor derived from Ni(OH)_(2)nanosheets was modified at both the core and shell interfaces with MgO via wet impregnation.The obtained 0.8MgO^(WI)/Ni@NiAlO catalyst achieved a high CH_(4)reaction rate of~177 mmol gNi^(-1)min^(-1)and remained stable for 50 h at 600℃without coke formation.In sharp contrast,other Mg-doped catalysts(MgO modified the core or shell interfaces)and the catalyst without Mg-doping deactivated within 10 h due to coking or Ni particle sintering.The Ni/MgNiO_(2)interfaces and abundant oxygen vacancies(O_(v))generated by Mg-doping contributed to the outstanding resistance to sintering&coking as well as the superior activity and stability of the 0.8MgO^(WI)/Ni@NiAlO catalyst.In-situ investigation further unveiled the reaction mechanism:the activation of CO_(2)via adsorption on O_(v)generates active oxygen species(O^(*)),which reacts with CH_(x)^(*)intermediates formed by the dissociation of CH_(4)on Ni sites,yielding CO and H_(2).This work not only fabricates coke-free and high-stability Ni-based DRM catalysts via interface engineering but also provides insights and a new strategy for the design of high-efficiency and stable catalysts for DRM.展开更多
Carbon dioxide and methane are two main greenhouse gases which are contributed to serious global warming.Fortunately,dry reforming of methane(DRM),a very important reaction developed decades ago,can convert these two ...Carbon dioxide and methane are two main greenhouse gases which are contributed to serious global warming.Fortunately,dry reforming of methane(DRM),a very important reaction developed decades ago,can convert these two major greenhouse gases into value-added syngas or hydrogen.The main problem retarding its industrialization is the seriously coking formation upon the nickel-based catalysts.Herein,a series of confined indium-nickel(In-Ni)intermetallic alloy nanocatalysts(In_(x)Ni@SiO_(2))have been prepared and displayed superior coking resistance for DRM reaction.The sample containing 0.5 wt.%of In loading(In_(0.5)Ni@SiO_(2))shows the best balance of carbon deposition resistance and DRM reactivity even after 430 h long term stability test.The boosted carbon resistance can be ascribed to the confinement of core–shell structure and to the transfer of electrons from Indium to Nickel in In-Ni intermetallic alloys due to the smaller electronegativity of In.Both the silica shell and the increase of electron cloud density on metallic Ni can weaken the ability of Ni to activate C–H bond and decrease the deep cracking process of methane.The reaction over the confined InNi intermetallic alloy nanocatalyst was conformed to the Langmuir-Hinshelwood(L-H)mechanism revealed by in situ diffuse reflectance infrared Fourier transform spectroscopy(in-situ DRIFTS).This work provides a guidance to design high performance coking resistance catalysts for methane dry reforming to efficiently utilize these two main greenhouse gases.展开更多
In this work the effects of the contents of nickel （5, 7.5, 10 wt%） and copper （0, 1, 2 wt%） and reac- tion temperature （650, 700, 750 ℃） on the catalytic performance of Ni-Cu/Al_2O_3 catalyst in methane dry re...In this work the effects of the contents of nickel （5, 7.5, 10 wt%） and copper （0, 1, 2 wt%） and reac- tion temperature （650, 700, 750 ℃） on the catalytic performance of Ni-Cu/Al_2O_3 catalyst in methane dry reforming were evaluated using Box-Behnken design in order to optimize methane conversion, H_2/CO ratio and the catalyst deactivation. Different catalysts were prepared by co-impregnation method and characterized by XRD, BET, H_2-TPR, FESEM and TG/DTA analyses. The results revealed that copper addi- tion improved the catalyst reducibility. Promoted catalyst with low amounts of Cu gave higher activity and stability with high resistance to coke deposition and agglomeration of active phase especially during the reaction. However catalysts with high amounts of Cu were less active and rather deactivated due to the active sites sintering as well as Ni covering by Cu-enriched phase. The optimal conditions were de- termined by desirability function approach as 10 wt% of Ni, 0.83 wt% of Cu at 750℃. CH_4 conversion of 95.1%, H_2/CO ratio of 1 and deactivation of 1.4% were obtained experimentally under optimum conditions, which were in close agreement with the values oredicted hv the developed model.展开更多
A series of Ni/La2Zr2O7 pyrochlore catalysts prepared by impregnation method and treated by dielectric barrier discharge（DBD） plasma in different atmospheres and varied sequences were prepared and applied for dry re...A series of Ni/La2Zr2O7 pyrochlore catalysts prepared by impregnation method and treated by dielectric barrier discharge（DBD） plasma in different atmospheres and varied sequences were prepared and applied for dry reforming of methane（DRM）. It is found that all of the plasma treated catalysts show evidently improved activity and coke resistance in comparison with the non-plasma treated one. The best performance is achieved on Ni/La2Zr2O7–H2P–C,a catalyst treated in H2 plasma before calcination. TGA-DSC and SEM demonstrate that carbon deposition is significantly suppressed on all of the plasma treated samples. Moreover,XRD and TEM results testify that both Ni O and Ni sizes on the calcined and reduced samples treated by plasma are also decreased,which results in higher Ni metal dispersion on the reduced and used catalysts and enhances the interactions between Ni sites and the support. It is believed that these are the inherent reasons accounting for the promotional effects of plasma treatment on the reaction performance of the Ni/La2Zr2O7 pyrochlore catalysts.展开更多
High surface area mixed oxide 8.7%NiO-CeO_(2) nanoparticles(122 m2/g;6-7 nm)were prepared using a reversed microemulsion method,and were tested for dry methane reforming(DRM).The catalytic activity of these nanopartic...High surface area mixed oxide 8.7%NiO-CeO_(2) nanoparticles(122 m2/g;6-7 nm)were prepared using a reversed microemulsion method,and were tested for dry methane reforming(DRM).The catalytic activity of these nanoparticles remains stable under the severe conditions of DRM(700℃),and they show better carbon resistance than conventional NiO-CeO_(2) catalysts prepared without control of the size.The activity and selectivity of nanoparticles and reference catalyst are similar,but nanoparticles reduce the accumulation of carbon by 63%during the DRM tests,which is a key feature for this reaction.XPS and H_(2)-TPR suggest that the improved carbon resistance of the nanoparticles is due to the better interaction and cooperation between NiO and CeO_(2) mixed phases.In nanoparticles,the participation of cerium cations in the redox processes taking place during DRM stabilizes cationic species of nickel.On the contrary,the catalyst prepared without control of the size suffers segregation of Ni during DRM reaction,and segregated Ni explains the higher catalytic formation of carbon.展开更多
A series of Co/γ-Al_2O_3 catalysts were prepared with the impregnation method and characterized by means of the BET specific surface area, X-ray diffraction(XRD), thermogravimetric analysis(TGA) and Laser Raman spect...A series of Co/γ-Al_2O_3 catalysts were prepared with the impregnation method and characterized by means of the BET specific surface area, X-ray diffraction(XRD), thermogravimetric analysis(TGA) and Laser Raman spectroscopy. The Co/γ-Al_2O_3 catalysts were activated by using H_2, 20%CH_4/H_2 or CH_4, respectively. There was no obvious difference between the activities of the Co/γ-Al_2O_3 catalyst activated by using the different activation methods for methane dry reforming. The catalytic properties of the Co/γ-Al_2O_3 catalysts with different Co loadings were also investigated. The optimized Co loading for the Co/γ-Al_2O_3 catalyst pretreated with 20% CH_4/H_2 is around 12%(mass fraction).展开更多
Ultrafine metal nanoparticles(NPs)play a central role in heterogeneous catalysis,offering exceptional atomic efficiency and tunable active sites.However,their inherent thermodynamic instability under harsh conditions,...Ultrafine metal nanoparticles(NPs)play a central role in heterogeneous catalysis,offering exceptional atomic efficiency and tunable active sites.However,their inherent thermodynamic instability under harsh conditions,such as high temperatures and reducing atmospheres,leads to sintering driven by either particle migration and coalescence or Ostwald ripening[1].展开更多
Photothermal catalytic methane dry reforming(DRM)technology can convert greenhouse gases(i.e.CH_(4)and CO_(2))into syngas(i.e.H_(2)and CO),providing more opportunities for reducing the greenhouse effect and achieving ...Photothermal catalytic methane dry reforming(DRM)technology can convert greenhouse gases(i.e.CH_(4)and CO_(2))into syngas(i.e.H_(2)and CO),providing more opportunities for reducing the greenhouse effect and achieving carbon neutrality.In the DRM field,Ni-based catalysts attract wide attention due to their low cost and high activity.However,the carbon deposition over Ni-based catalysts always leads to rapid deactivation,which is still a main challenge.To improve the long-term stability of Ni-based catalysts,this work proposes a carbon-atom-diffusion strategy under photothermal conditions and investigates its effect on a Zn-doped Ni-based photothermal catalyst(Ni_(3)Zn@CeO_(2)).The photothermal catalytic behavior of Ni_(3)Zn@CeO_(2)can maintain more than 70 h in DRM reaction.And the photocatalytic DRM activity of Ni_(3)Zn@CeO_(2)is 1.2 times higher than thermal catalytic activity.Density functional theory(DFT)calculation and experimental characterizations indicate that Ni_(3)Zn promotes the diffusion of carbon atoms into the Ni_(3)Zn to form the Ni_(3)ZnC0.7 phase with body-centered cubic(bcc)structure,thus inhibiting carbon deposition.Further,in-situ diffuse reflectance infrared Fourier transform(DRIFT)spectroscopy and DFT calculation prove Ni_(3)Zn@CeO_(2)benefits the CH_(4)activation and inhibits the carbon deposition during the DRM process.Through inducing carbon atoms diffusion within the Ni_(3)Zn lattice,this work provides a straightforward and feasible strategy for achieving efficient photothermal catalytic DRM and even other CH_(4)conversion implementations with long-term stability.展开更多
Dry reforming of methane(DRM)has gained significant attention as a promising route to convert two major greenhouse gases(CO_(2) and CH4)to syngas.The development of efficient catalysts is critical for the engineering ...Dry reforming of methane(DRM)has gained significant attention as a promising route to convert two major greenhouse gases(CO_(2) and CH4)to syngas.The development of efficient catalysts is critical for the engineering applications.In this study,the Ce_(x)Zr_(1-x)O_(2)/ZSM-5 composites with different oxygen vacancy concentrations were synthesized by tuning the Ce/Zr ratio,followed by the deposition of metal Ni to island-like Ce_(x)Zr_(1-x)O_(2)on ZSM-5,forming a variety of Ni-Ce_(x)Zr_(1-x)O_(2)/ZSM-5 catalysts,which were applied for the DRM reaction under 750◦C.Combined with various characterizations,it was found that the oxygen vacancy concentration illustrated the volcanic tendency with the decreased Ce/Zr ratio,and the interaction between metal Ni and Ce_(x)Zr_(1-x)O_(2)exhibited a positive relationship with oxygen vacancy concentration.The enhanced between Ni and Ce_(x)Zr_(1-x)O_(2)interaction could improve the strength and amount of Ni-O-M(M=Ce/Zr)species,making the d-band centers of catalysts closer to the Fermi energy level,which was beneficial to the CH4 and CO_(2) activation,along with the improved capacity to resist sintering and coking.Especially,the C1Z3(Ni-Ce0.25Zr0.75O_(2)/ZSM-5)catalyst with the Ce/Zr ratio of 1/3 demonstrated the optimal catalytic performance with 91.9%CH4 and 93.8%CO_(2) conversions within 50 h,accompanied by the best structural and catalytic stability after 100 h.In-situ DRIFTS was employed to study the reaction path and mechanism,discovering that significant amounts of strengthened Ni-O-M species were conducive to activating adsorbed CH4 and CO_(2),and desorbing the linear CO species.展开更多
CeO_(2) based semiconductor are widely used in solar-driven photothermal catalytic dry reforming of methane(DRM)reaction,but still suffer from low activity and low light utilization efficiency.This study developed gra...CeO_(2) based semiconductor are widely used in solar-driven photothermal catalytic dry reforming of methane(DRM)reaction,but still suffer from low activity and low light utilization efficiency.This study developed graphite-CeO_(2) interfaces to enhance solar-driven photothermal catalytic DRM.Compared with carbon nanotubes-modified CeO_(2)(CeO_(2)-CNT),graphite-modified CeO_(2)(CeO_(2)-GRA)constructed graphite-CeO_(2) interfaces with distortion in CeO_(2),leading to the formation abundant oxygen vacancies.These graphite-CeO_(2) interfaces with oxygen vacancies enhanced optical absorption and promoted the generation and separation of photogenerated carriers.The high endothermic capacity of graphite elevated the catalyst surface temperature from 592.1−691.3℃,boosting light-to-thermal conversion.The synergy between photogenerated carriers and localized heat enabled Ni/CeO_(2)-GRA to achieve a CO production rate of 9985.6 mmol/(g·h)(vs 7192.4 mmol/(g·h)for Ni/CeO_(2))and a light-to-fuel efficiency of 21.8%(vs 13.8%for Ni/CeO_(2)).This work provides insights for designing graphite-semiconductor interfaces to advance photothermal catalytic efficiency.展开更多
Developing cost-effective and high-performance catalyst systems for dry reforming of methane(DRM)is crucial for producing hydrogen(H_(2))sustainably.Herein,we investigate using iron(Fe)as a promoter and major alumina ...Developing cost-effective and high-performance catalyst systems for dry reforming of methane(DRM)is crucial for producing hydrogen(H_(2))sustainably.Herein,we investigate using iron(Fe)as a promoter and major alumina support in Ni-based catalysts to improve their DRM performance.The addition of iron as a promotor was found to add reducible iron species along with reducible NiO species,enhance the basicity and induce the deposition of oxidizable carbon.By incorporating 1 wt.%Fe into a 5Ni/10ZrAl catalyst,a higher CO_(2) interaction and formation of reducible"NiO-species having strong interaction with support"was observed,which led to an∼80%H_(2) yield in 420 min of Time on Stream(TOS).Further increasing the Fe content to 2 wt.%led to the formation of additional reducible iron oxide species and a noticeable rise in H_(2) yield up to 84%.Despite the severe weight loss on Fe-promoted catalysts,high H_(2) yield was maintained due to the proper balance between the rate of CH_(4) decomposition and the rate of carbon deposit diffusion.Finally,incorporating 3 wt.%Fe into the 5Ni/10ZrAl catalyst resulted in the highest CO_(2) interaction,wide presence of reducible NiO-species,minimumgraphitic deposit and an 87%H_(2) yield.Our findings suggest that ironpromoted zirconia-alumina-supported Ni catalysts can be a cheap and excellent catalytic system for H_(2) production via DRM.展开更多
The upgrading of underutilized methane in shale gas with anthropogenic CO_(2) can produce the valueadded syngas via dry reforming.Nickel-based catalysts,due to their efficiency and cost-effectiveness,have received wid...The upgrading of underutilized methane in shale gas with anthropogenic CO_(2) can produce the valueadded syngas via dry reforming.Nickel-based catalysts,due to their efficiency and cost-effectiveness,have received widespread attention.However,Ni-catalyzed dry reforming of methane is usually subjected to sintering or coking-induced instability.To address these issues,a series of Al2O_(3)-supported nickel nanoparticle catalysts with uniform sizes are synthesized by varying the calcination temperatures and applied in methane dry reforming(DRM).Ni/Al_(2)O_(3)-700℃ catalyst behaves better catalytic performance compared to the other catalysts,which can be attributed to its higher metal dispersion and stronger metalsupport interaction.In addition,the abundant moderatestrength basic sites and optimal Al_(Ⅳ)/Al_(Ⅵ) ratio can promote the adsorption and activation of CO_(2) and suppress the deep cracking of CH_(4) for Ni/Al_(2)O_(3)-700℃ catalyst,respectively,causing the enhancement of anti-coking performance.Furthermore,combining CH_(4)-temperature programmed surface reaction and in situ Fourier transform infrared spectroscopy demonstrates that the presence of CO_(2) can promote the activation of CH_(4) for Ni/Al_(2)O_(3)-700℃ catalyst,which is rate-determining step for DRM system.These findings provide valuable theoretical guidance for the rational design of Ni-based catalysts with enhanced catalytic performance.展开更多
Energy shortages and global warming are driving the focus on the greenhouse gases CH_(4)and CO_(2).The main reason why dry reforming of methane(DRM)has yet to be industrialized is its catalytic tendency to deactivate ...Energy shortages and global warming are driving the focus on the greenhouse gases CH_(4)and CO_(2).The main reason why dry reforming of methane(DRM)has yet to be industrialized is its catalytic tendency to deactivate due to carbon deposition or sintering.Single-atom Ni/CeO_(2)catalysts with suitable metalsupport interactions may provide a new strategy for developing highly active and coking-resistant nickel-based catalysts.In this work,we investigated the properties of the catalytic models of singleatom Ni loaded on CeO_(2)(111),CeO_(2)(110)and CeO_(2)(100),as well as their catalytic DRM performance with the density functional theory method(DFT).The interaction of CeO_(2)with different low-index crystal planes and single-atom Ni can be explained by the anchoring effect of surface O ions on Ni.Adsorption energies,growth patterns of Ni clusters,and migration studies of Ni atoms all indicate that the CeO_(2)(100)surface has the strongest anchoring effect on isolated Ni atoms,followed by the CeO_(2)(110)surface,with the CeO_(2)(111)surface being the weakest,Methane activation studies have shown that the activation ability of Ni_(1)/CeO_(2)(110)for methane strongly depends on the coordination environment of Ni,By contrast,methane activation by Ni on Ni_(1)/CeO_(2)(111)exhibits better activity and stability.Moreover,the Ni—CeO_(2)interaction correlates well with the DRM reaction performance.Interactions that are too strong anchor Ni atoms well but are not optimal for DRM activity.Ni_(1)/CeO_(2)(110)has relatively moderate interactions,promotes the^(*)CH_(4)→^(*)CH process,and has good resistance to carbon deposition.The metalsupport interaction-DRM reactivity(or stability)relationship is vital for the design of"super"highactivity and high-stability DRM catalysts.展开更多
Li_(6)ZnO_(4)was chemically modified by nickel addition,in order to develop different compositions of the solid solution Li_(6)Zn_(1-x)Ni_(x)O_(4).These materials were evaluated bifunctionally;analyzing their CO_(2)ca...Li_(6)ZnO_(4)was chemically modified by nickel addition,in order to develop different compositions of the solid solution Li_(6)Zn_(1-x)Ni_(x)O_(4).These materials were evaluated bifunctionally;analyzing their CO_(2)capture performances,aswell as on their catalytic properties for H_(2)production via dry reforming of methane(DRM).The crystal structures of Li_(6)Zn_(1-x)Ni_(x)O_(4)solid solution samples were determined through X-ray diffraction,which confirmed the integration of nickel ions up to a concentration around 20 mol%,meanwhile beyond this value,a secondary phase was detected.These results were supported by XPS and TEM analyses.Then,dynamic and isothermal thermogravimetric analyses of CO_(2)capture revealed that Li_(6)Zn_(1-x)Ni_(x)O_(4)solid solution samples exhibited good CO_(2)chemisorption efficiencies,similarly to the pristine Li_(6)ZnO_(4)chemisorption trends observed.Moreover,a kinetic analysis of CO_(2)isothermal chemisorptions,using the Avrami-Erofeev model,evidenced an increment of the constant rates as a function of the Ni content.Since Ni^(2+)ions incorporation did not reduce the CO_(2)capture efficiency and kinetics,the catalytic properties of thesematerialswere evaluated in the DRM process.Results demonstrated that nickel ions favored hydrogen(H_(2))production over the pristine Li_(6)ZnO_(4)phase,despite a second H2 production reaction was determined,methane decomposition.Thereby,Li_(6)Zn_(1-x)Ni_(x)O_(4)ceramics can be employed as bifunctional materials.展开更多
An immature pinecone shaped hierarchically structured zirconia （ZrO2-ipch） and a cobblestone-like zirconia nanoparticulate （ZrO2-cs）, both with the monoclinic phase （m-phase）, were synthesized by the facile hydr...An immature pinecone shaped hierarchically structured zirconia （ZrO2-ipch） and a cobblestone-like zirconia nanoparticulate （ZrO2-cs）, both with the monoclinic phase （m-phase）, were synthesized by the facile hydrothermal method and used as the support for a Ni catalyst for the dry reforming of methane （DRM） with CO2. ZrO2-ipch is a much better support than ZrO2-cs and the traditional ZrO2 irregular particles made by a simple precipitation method （ZrO2-ip）. The supported Ni catalyst on ZrO2-ipch （Ni/ZrO2-ipch） exhibited outstanding catalytic activity and coke-resistant stability compared to the ones on ZrO2-cs （Ni/ZrO2-cs） and ZrO2-ip （Ni/ZrO2-ip）. Ni/ZrO2-ip exhibited the worst catalytic performance. The origin of the significantly enhanced catalytic performance was revealed by characterization including XRD, N2 adsorption measurement （BET）, TEM, H2-TPR, CO chemisorption, CO2-TPD, XPS and TGA. The superior catalytic activity of Ni/ZrO2-ipch to Ni/ZrO2-cs or Ni/ZrO2-ip was ascribed to a higher Ni dispersion, increased reducibility, enhanced oxygen mo- bility, and more basic sites with a higher strength, which were due to the unique hierarchically structural morphology of the ZrO2-ipch support. Ni/ZrO2-ipch exhibited better stability for the DRM reaction than Ni/ZrO2-ip, which was ascribed to its higher resistance to Ni sintering due to a strengthened metal-support interaction and the confinement effect of the mesopores and coke deposition resistance. The higher coking resistance of Ni/ZrO2-ipch for the DRM reaction in comparison with Ni/ZrOz-ip orignated from the coke-removalabitity of the higher amount of lattice oxygen and more basic sites, confirmed by XPS and CO2-TPD analysis, and the stabilized Ni on the Ni/ZrO2-ipch catalyst by the confinement effect of the mesopores of the hierarchical ZrO2-ipch sup- port. The superior catalytic performance and coking resistance of the Ni/ZrO2-ipch catalyst makes it a promising candidate for synthesis gas production from the DRM reaction.展开更多
In this study, Ni/YZrOcatalysts prepared with impregnation method and treated by dielectric barrier discharge plasma(DBD) in different atmospheres have been investigated for methane dry reforming. It is revealed by H-...In this study, Ni/YZrOcatalysts prepared with impregnation method and treated by dielectric barrier discharge plasma(DBD) in different atmospheres have been investigated for methane dry reforming. It is revealed by H-TPR that plasma treatment can enhance the interaction between Ni O/Ni particles and the YZrOpyrochlore support. Therefore, catalysts with smaller Ni O and Ni grains sizes, higher metallic Ni active surface areas can be achieved, as evidenced by XRD, TEM and Hadsorption-desorption measurements. As a consequence, the plasma-treated catalysts show significantly improved activity, stability and coke resistance, as testified by the TEM and TGA-DSC results. Plasma treatment in H/Ar gas mixture is found to be the best condition to prepare Ni/YZrO, which can be used to obtain a catalyst with the highest activity, stability and most potent coke resistance. It is believed that the smaller Ni grain size and higher metallic Ni active surface area induced by plasma treatment are the inherent reasons accounting for the promoted reaction performance of the Ni/YZrOpyrochlore catalysts.展开更多
Supported nickel catalysts are promising candidates for dry reforming of methane, but agglomeration of Ni^(0) and coke deposition hinder the industrial applications. Herein, we report a novel interface-directed synthe...Supported nickel catalysts are promising candidates for dry reforming of methane, but agglomeration of Ni^(0) and coke deposition hinder the industrial applications. Herein, we report a novel interface-directed synthetic approach to construct distinct metal ensembles by carefully tuning the compositions of the carriers. A Zr-Mn-Zn ternary oxide-supported Ni catalyst, together with the respective binary oxide-supported analogues, was synthesized by adopting a sequential co-precipitation and wetness impregnation method. Combined characterization techniques identify distinct catalyst models, including (i) conventional NiO nanoparticles with different sizes on Zr-Mn and Zr-Zn, and (ii) epitaxially growing NiO ensembles of a few nanometers thickness at the periphery of ZnO_(x) particles. These catalysts exhibit divergent responses in the catalytic testing, with the ternary oxide system significantly outperforming the binary analogues. The strong electronic interactions between Mn-Ni increase Ni dispersion and the activity while the stability is strengthened upon Zn addition. Both high activity, high selectivity, and remarkable stability are attained upon co-adding Mn and Zn. The interfaces between Ni and Zr-Mn-Zn rather than the physical contacts of individual oxide-supported analogues through mechanical mixing are keys for the outstanding performance.展开更多
In this study, the use of a thermally stable Ir/Ce0.9La0.1O2 catalyst was investigated for the dry reforming of methane. The doping of La203 into the CeO2 lattice enhanced the chemical and physical properties of the I...In this study, the use of a thermally stable Ir/Ce0.9La0.1O2 catalyst was investigated for the dry reforming of methane. The doping of La203 into the CeO2 lattice enhanced the chemical and physical properties of the Ir/Ce0.9La0.1O2 catalyst, such as redox properties, Ir dispersion, oxygen storage capacity, and thermal stability, with respect to the Ir/CeO2 catalyst. Hence, the Ir/Ce0.9La0.1O2 catalyst exhibits higher activity and stabler performance for the dry reforming of methane than the Ir/CeO2 catalyst. This observation can be mainly attributed to the stronger interaction between the metal and support in the Ir/Ce0.9La0.1O2 catalyst stabilizing the catalyst structure and improving the oxygen storage capacity, leading to negligible aggregation of Ir nanoparticles and the Ce0.9La0.1O2 support at high temperatures, as well as the rapid removal of carbon deposits at the boundaries between the Ir metal and the Ce0.9La0.1O2 support.展开更多
Ni-Co bimetallic catalysts with different Ni/Co content were derived from cold plasma jet decomposition and reduction of hydrotalcite-like compounds containing Ni,Co,Mg and Al,and their catalytic performance was inves...Ni-Co bimetallic catalysts with different Ni/Co content were derived from cold plasma jet decomposition and reduction of hydrotalcite-like compounds containing Ni,Co,Mg and Al,and their catalytic performance was investigated with dry reforming of methane.Experimental results showed that the hydrotalcite-like precursors could be completely decomposed and partly reduced by cold plasma jet,and the Nicontained catalysts exhibited much higher activity than the catalyst without Ni.Especially,the catalyst with Ni/Co ratio of 8/2 achieved not only the highest conversions of 80.3%and 69.3%for CH4 and CO2,respectively,but also the best stability in 100 h testing.The catalysts were characterized by XRD,XPS,TEM and N2 adsorption techniques,and the results showed that the better performance of the 8Ni2Co bimetallic catalyst was attributed to its higher metal dispersion,smaller metal particle size,as well as the interaction effect between Ni and Co,which were brought by the special catalyst preparation method.展开更多
文摘It is economical to perform methane and carbon dioxide reforming(DRM)under industrially relevant high-pressure conditions,but the harsh operation condition poses a grand challenge for coke-resistant catalyst design.Here,we propose to boost the coke-tolerance of Co catalyst by applying a contact potential introduced by immiscible Ag clusters.We demonstrate that Co clusters separated by neighboring Ag on Yttria-stabilized zirconia(YSZ)support can serve as a coke-and sintering-resistant DRM catalyst under diluent gas-free,stoichiometric CH_(4) and CO_(2) feeding,1123 K and 20 bar.Since immiscible metals are ubiquitous and metal contact influences surface work function in general,this new design concept may have general implications for tailoring catalytic properties of metals.
文摘In the past decade,dry reforming of methane(DRM)has garnered increasing interest as it converts CH_(4)and CO_(2),two typical greenhouse gases,into synthesis gas(H_(2)and CO)for the production of high-value-added chemicals and fuels.Nickel-based DRM catalysts,renowned for their high activity and low cost,however,encounter challenges such as severe deactivation from sintering and carbon deposition.Herein,a surrounded NiO@NiAlO precursor derived from Ni(OH)_(2)nanosheets was modified at both the core and shell interfaces with MgO via wet impregnation.The obtained 0.8MgO^(WI)/Ni@NiAlO catalyst achieved a high CH_(4)reaction rate of~177 mmol gNi^(-1)min^(-1)and remained stable for 50 h at 600℃without coke formation.In sharp contrast,other Mg-doped catalysts(MgO modified the core or shell interfaces)and the catalyst without Mg-doping deactivated within 10 h due to coking or Ni particle sintering.The Ni/MgNiO_(2)interfaces and abundant oxygen vacancies(O_(v))generated by Mg-doping contributed to the outstanding resistance to sintering&coking as well as the superior activity and stability of the 0.8MgO^(WI)/Ni@NiAlO catalyst.In-situ investigation further unveiled the reaction mechanism:the activation of CO_(2)via adsorption on O_(v)generates active oxygen species(O^(*)),which reacts with CH_(x)^(*)intermediates formed by the dissociation of CH_(4)on Ni sites,yielding CO and H_(2).This work not only fabricates coke-free and high-stability Ni-based DRM catalysts via interface engineering but also provides insights and a new strategy for the design of high-efficiency and stable catalysts for DRM.
基金supported by the National Natural Science Foundation of China(21976078 and 21773106)the National Key R&D Program of China(2016YFC0205900)+1 种基金the Natural Science Foundation of Jiangxi Province(20202ACB213001)National Engineering Laboratory for Mobile Source Emission Control Technology(NELMS2019A12)。
文摘Carbon dioxide and methane are two main greenhouse gases which are contributed to serious global warming.Fortunately,dry reforming of methane(DRM),a very important reaction developed decades ago,can convert these two major greenhouse gases into value-added syngas or hydrogen.The main problem retarding its industrialization is the seriously coking formation upon the nickel-based catalysts.Herein,a series of confined indium-nickel(In-Ni)intermetallic alloy nanocatalysts(In_(x)Ni@SiO_(2))have been prepared and displayed superior coking resistance for DRM reaction.The sample containing 0.5 wt.%of In loading(In_(0.5)Ni@SiO_(2))shows the best balance of carbon deposition resistance and DRM reactivity even after 430 h long term stability test.The boosted carbon resistance can be ascribed to the confinement of core–shell structure and to the transfer of electrons from Indium to Nickel in In-Ni intermetallic alloys due to the smaller electronegativity of In.Both the silica shell and the increase of electron cloud density on metallic Ni can weaken the ability of Ni to activate C–H bond and decrease the deep cracking process of methane.The reaction over the confined InNi intermetallic alloy nanocatalyst was conformed to the Langmuir-Hinshelwood(L-H)mechanism revealed by in situ diffuse reflectance infrared Fourier transform spectroscopy(in-situ DRIFTS).This work provides a guidance to design high performance coking resistance catalysts for methane dry reforming to efficiently utilize these two main greenhouse gases.
文摘In this work the effects of the contents of nickel （5, 7.5, 10 wt%） and copper （0, 1, 2 wt%） and reac- tion temperature （650, 700, 750 ℃） on the catalytic performance of Ni-Cu/Al_2O_3 catalyst in methane dry reforming were evaluated using Box-Behnken design in order to optimize methane conversion, H_2/CO ratio and the catalyst deactivation. Different catalysts were prepared by co-impregnation method and characterized by XRD, BET, H_2-TPR, FESEM and TG/DTA analyses. The results revealed that copper addi- tion improved the catalyst reducibility. Promoted catalyst with low amounts of Cu gave higher activity and stability with high resistance to coke deposition and agglomeration of active phase especially during the reaction. However catalysts with high amounts of Cu were less active and rather deactivated due to the active sites sintering as well as Ni covering by Cu-enriched phase. The optimal conditions were de- termined by desirability function approach as 10 wt% of Ni, 0.83 wt% of Cu at 750℃. CH_4 conversion of 95.1%, H_2/CO ratio of 1 and deactivation of 1.4% were obtained experimentally under optimum conditions, which were in close agreement with the values oredicted hv the developed model.
基金supported by the Chinese Natural Science Foundation (21263015 and 21203088)the Education Department of Jiangxi Province (KJLD14005 and GJJ14205)the Natural Science Foundation of Jiangxi Province (20142BAB213013)
文摘A series of Ni/La2Zr2O7 pyrochlore catalysts prepared by impregnation method and treated by dielectric barrier discharge（DBD） plasma in different atmospheres and varied sequences were prepared and applied for dry reforming of methane（DRM）. It is found that all of the plasma treated catalysts show evidently improved activity and coke resistance in comparison with the non-plasma treated one. The best performance is achieved on Ni/La2Zr2O7–H2P–C,a catalyst treated in H2 plasma before calcination. TGA-DSC and SEM demonstrate that carbon deposition is significantly suppressed on all of the plasma treated samples. Moreover,XRD and TEM results testify that both Ni O and Ni sizes on the calcined and reduced samples treated by plasma are also decreased,which results in higher Ni metal dispersion on the reduced and used catalysts and enhances the interactions between Ni sites and the support. It is believed that these are the inherent reasons accounting for the promotional effects of plasma treatment on the reaction performance of the Ni/La2Zr2O7 pyrochlore catalysts.
基金Project supported by the Generalitat Valenciana(PROMETEO/2018/076ACA GRISOLIAP/2017/185+3 种基金EBG APOSTD/2019/030)MINECO(CTQ2015-67597-C2-2-R)MICINN(PID2019-105960RB-C22)European Union FEDER funds。
文摘High surface area mixed oxide 8.7%NiO-CeO_(2) nanoparticles(122 m2/g;6-7 nm)were prepared using a reversed microemulsion method,and were tested for dry methane reforming(DRM).The catalytic activity of these nanoparticles remains stable under the severe conditions of DRM(700℃),and they show better carbon resistance than conventional NiO-CeO_(2) catalysts prepared without control of the size.The activity and selectivity of nanoparticles and reference catalyst are similar,but nanoparticles reduce the accumulation of carbon by 63%during the DRM tests,which is a key feature for this reaction.XPS and H_(2)-TPR suggest that the improved carbon resistance of the nanoparticles is due to the better interaction and cooperation between NiO and CeO_(2) mixed phases.In nanoparticles,the participation of cerium cations in the redox processes taking place during DRM stabilizes cationic species of nickel.On the contrary,the catalyst prepared without control of the size suffers segregation of Ni during DRM reaction,and segregated Ni explains the higher catalytic formation of carbon.
文摘A series of Co/γ-Al_2O_3 catalysts were prepared with the impregnation method and characterized by means of the BET specific surface area, X-ray diffraction(XRD), thermogravimetric analysis(TGA) and Laser Raman spectroscopy. The Co/γ-Al_2O_3 catalysts were activated by using H_2, 20%CH_4/H_2 or CH_4, respectively. There was no obvious difference between the activities of the Co/γ-Al_2O_3 catalyst activated by using the different activation methods for methane dry reforming. The catalytic properties of the Co/γ-Al_2O_3 catalysts with different Co loadings were also investigated. The optimized Co loading for the Co/γ-Al_2O_3 catalyst pretreated with 20% CH_4/H_2 is around 12%(mass fraction).
文摘Ultrafine metal nanoparticles(NPs)play a central role in heterogeneous catalysis,offering exceptional atomic efficiency and tunable active sites.However,their inherent thermodynamic instability under harsh conditions,such as high temperatures and reducing atmospheres,leads to sintering driven by either particle migration and coalescence or Ostwald ripening[1].
文摘Photothermal catalytic methane dry reforming(DRM)technology can convert greenhouse gases(i.e.CH_(4)and CO_(2))into syngas(i.e.H_(2)and CO),providing more opportunities for reducing the greenhouse effect and achieving carbon neutrality.In the DRM field,Ni-based catalysts attract wide attention due to their low cost and high activity.However,the carbon deposition over Ni-based catalysts always leads to rapid deactivation,which is still a main challenge.To improve the long-term stability of Ni-based catalysts,this work proposes a carbon-atom-diffusion strategy under photothermal conditions and investigates its effect on a Zn-doped Ni-based photothermal catalyst(Ni_(3)Zn@CeO_(2)).The photothermal catalytic behavior of Ni_(3)Zn@CeO_(2)can maintain more than 70 h in DRM reaction.And the photocatalytic DRM activity of Ni_(3)Zn@CeO_(2)is 1.2 times higher than thermal catalytic activity.Density functional theory(DFT)calculation and experimental characterizations indicate that Ni_(3)Zn promotes the diffusion of carbon atoms into the Ni_(3)Zn to form the Ni_(3)ZnC0.7 phase with body-centered cubic(bcc)structure,thus inhibiting carbon deposition.Further,in-situ diffuse reflectance infrared Fourier transform(DRIFT)spectroscopy and DFT calculation prove Ni_(3)Zn@CeO_(2)benefits the CH_(4)activation and inhibits the carbon deposition during the DRM process.Through inducing carbon atoms diffusion within the Ni_(3)Zn lattice,this work provides a straightforward and feasible strategy for achieving efficient photothermal catalytic DRM and even other CH_(4)conversion implementations with long-term stability.
基金the following financial supports:National Natural Science Foundation of China(22075225 and 22038011)Innovative Scientific Program of CNNC,State Key Laboratory of Clean and Efficient Coal Utilization,Taiyuan University of Technology(MJNYSKL202401,MJNYSKL202404).
文摘Dry reforming of methane(DRM)has gained significant attention as a promising route to convert two major greenhouse gases(CO_(2) and CH4)to syngas.The development of efficient catalysts is critical for the engineering applications.In this study,the Ce_(x)Zr_(1-x)O_(2)/ZSM-5 composites with different oxygen vacancy concentrations were synthesized by tuning the Ce/Zr ratio,followed by the deposition of metal Ni to island-like Ce_(x)Zr_(1-x)O_(2)on ZSM-5,forming a variety of Ni-Ce_(x)Zr_(1-x)O_(2)/ZSM-5 catalysts,which were applied for the DRM reaction under 750◦C.Combined with various characterizations,it was found that the oxygen vacancy concentration illustrated the volcanic tendency with the decreased Ce/Zr ratio,and the interaction between metal Ni and Ce_(x)Zr_(1-x)O_(2)exhibited a positive relationship with oxygen vacancy concentration.The enhanced between Ni and Ce_(x)Zr_(1-x)O_(2)interaction could improve the strength and amount of Ni-O-M(M=Ce/Zr)species,making the d-band centers of catalysts closer to the Fermi energy level,which was beneficial to the CH4 and CO_(2) activation,along with the improved capacity to resist sintering and coking.Especially,the C1Z3(Ni-Ce0.25Zr0.75O_(2)/ZSM-5)catalyst with the Ce/Zr ratio of 1/3 demonstrated the optimal catalytic performance with 91.9%CH4 and 93.8%CO_(2) conversions within 50 h,accompanied by the best structural and catalytic stability after 100 h.In-situ DRIFTS was employed to study the reaction path and mechanism,discovering that significant amounts of strengthened Ni-O-M species were conducive to activating adsorbed CH4 and CO_(2),and desorbing the linear CO species.
文摘CeO_(2) based semiconductor are widely used in solar-driven photothermal catalytic dry reforming of methane(DRM)reaction,but still suffer from low activity and low light utilization efficiency.This study developed graphite-CeO_(2) interfaces to enhance solar-driven photothermal catalytic DRM.Compared with carbon nanotubes-modified CeO_(2)(CeO_(2)-CNT),graphite-modified CeO_(2)(CeO_(2)-GRA)constructed graphite-CeO_(2) interfaces with distortion in CeO_(2),leading to the formation abundant oxygen vacancies.These graphite-CeO_(2) interfaces with oxygen vacancies enhanced optical absorption and promoted the generation and separation of photogenerated carriers.The high endothermic capacity of graphite elevated the catalyst surface temperature from 592.1−691.3℃,boosting light-to-thermal conversion.The synergy between photogenerated carriers and localized heat enabled Ni/CeO_(2)-GRA to achieve a CO production rate of 9985.6 mmol/(g·h)(vs 7192.4 mmol/(g·h)for Ni/CeO_(2))and a light-to-fuel efficiency of 21.8%(vs 13.8%for Ni/CeO_(2)).This work provides insights for designing graphite-semiconductor interfaces to advance photothermal catalytic efficiency.
基金The authors would like to extend their sincere appreciation to Researchers Supporting Project number (RSP2023R368)King Saud University,Riyadh,Saudi Arabia.RK,NP,VKS acknowledge Indus University,Ahmedabad,for supporting research.Dr.Ahmed I.Osman and Prof.David W.Rooney wish to acknowledge the support of The Bryden Centre project (Project ID VA5048)。
文摘Developing cost-effective and high-performance catalyst systems for dry reforming of methane(DRM)is crucial for producing hydrogen(H_(2))sustainably.Herein,we investigate using iron(Fe)as a promoter and major alumina support in Ni-based catalysts to improve their DRM performance.The addition of iron as a promotor was found to add reducible iron species along with reducible NiO species,enhance the basicity and induce the deposition of oxidizable carbon.By incorporating 1 wt.%Fe into a 5Ni/10ZrAl catalyst,a higher CO_(2) interaction and formation of reducible"NiO-species having strong interaction with support"was observed,which led to an∼80%H_(2) yield in 420 min of Time on Stream(TOS).Further increasing the Fe content to 2 wt.%led to the formation of additional reducible iron oxide species and a noticeable rise in H_(2) yield up to 84%.Despite the severe weight loss on Fe-promoted catalysts,high H_(2) yield was maintained due to the proper balance between the rate of CH_(4) decomposition and the rate of carbon deposit diffusion.Finally,incorporating 3 wt.%Fe into the 5Ni/10ZrAl catalyst resulted in the highest CO_(2) interaction,wide presence of reducible NiO-species,minimumgraphitic deposit and an 87%H_(2) yield.Our findings suggest that ironpromoted zirconia-alumina-supported Ni catalysts can be a cheap and excellent catalytic system for H_(2) production via DRM.
基金Financial support by National Natural Science Foundation of China(Grant Nos.22408274,22438010 and 22075204)Ningbo Natural Science Foundation(Grant No.2024J137)+1 种基金the China Postdoctoral Science Foundation(Grant No.2023M742594)Innovative Group Project of Ningxia Natural Science Foundation(Grant No.2024AAC01002)is gratefully acknowledged.
文摘The upgrading of underutilized methane in shale gas with anthropogenic CO_(2) can produce the valueadded syngas via dry reforming.Nickel-based catalysts,due to their efficiency and cost-effectiveness,have received widespread attention.However,Ni-catalyzed dry reforming of methane is usually subjected to sintering or coking-induced instability.To address these issues,a series of Al2O_(3)-supported nickel nanoparticle catalysts with uniform sizes are synthesized by varying the calcination temperatures and applied in methane dry reforming(DRM).Ni/Al_(2)O_(3)-700℃ catalyst behaves better catalytic performance compared to the other catalysts,which can be attributed to its higher metal dispersion and stronger metalsupport interaction.In addition,the abundant moderatestrength basic sites and optimal Al_(Ⅳ)/Al_(Ⅵ) ratio can promote the adsorption and activation of CO_(2) and suppress the deep cracking of CH_(4) for Ni/Al_(2)O_(3)-700℃ catalyst,respectively,causing the enhancement of anti-coking performance.Furthermore,combining CH_(4)-temperature programmed surface reaction and in situ Fourier transform infrared spectroscopy demonstrates that the presence of CO_(2) can promote the activation of CH_(4) for Ni/Al_(2)O_(3)-700℃ catalyst,which is rate-determining step for DRM system.These findings provide valuable theoretical guidance for the rational design of Ni-based catalysts with enhanced catalytic performance.
基金Project supported by the Major Science and Technology Projects in Yunnan Province(202302AG050005)。
文摘Energy shortages and global warming are driving the focus on the greenhouse gases CH_(4)and CO_(2).The main reason why dry reforming of methane(DRM)has yet to be industrialized is its catalytic tendency to deactivate due to carbon deposition or sintering.Single-atom Ni/CeO_(2)catalysts with suitable metalsupport interactions may provide a new strategy for developing highly active and coking-resistant nickel-based catalysts.In this work,we investigated the properties of the catalytic models of singleatom Ni loaded on CeO_(2)(111),CeO_(2)(110)and CeO_(2)(100),as well as their catalytic DRM performance with the density functional theory method(DFT).The interaction of CeO_(2)with different low-index crystal planes and single-atom Ni can be explained by the anchoring effect of surface O ions on Ni.Adsorption energies,growth patterns of Ni clusters,and migration studies of Ni atoms all indicate that the CeO_(2)(100)surface has the strongest anchoring effect on isolated Ni atoms,followed by the CeO_(2)(110)surface,with the CeO_(2)(111)surface being the weakest,Methane activation studies have shown that the activation ability of Ni_(1)/CeO_(2)(110)for methane strongly depends on the coordination environment of Ni,By contrast,methane activation by Ni on Ni_(1)/CeO_(2)(111)exhibits better activity and stability.Moreover,the Ni—CeO_(2)interaction correlates well with the DRM reaction performance.Interactions that are too strong anchor Ni atoms well but are not optimal for DRM activity.Ni_(1)/CeO_(2)(110)has relatively moderate interactions,promotes the^(*)CH_(4)→^(*)CH process,and has good resistance to carbon deposition.The metalsupport interaction-DRM reactivity(or stability)relationship is vital for the design of"super"highactivity and high-stability DRM catalysts.
基金This work was carried out in the framework of PAPIIT-UNAM(IN-205823)project.
文摘Li_(6)ZnO_(4)was chemically modified by nickel addition,in order to develop different compositions of the solid solution Li_(6)Zn_(1-x)Ni_(x)O_(4).These materials were evaluated bifunctionally;analyzing their CO_(2)capture performances,aswell as on their catalytic properties for H_(2)production via dry reforming of methane(DRM).The crystal structures of Li_(6)Zn_(1-x)Ni_(x)O_(4)solid solution samples were determined through X-ray diffraction,which confirmed the integration of nickel ions up to a concentration around 20 mol%,meanwhile beyond this value,a secondary phase was detected.These results were supported by XPS and TEM analyses.Then,dynamic and isothermal thermogravimetric analyses of CO_(2)capture revealed that Li_(6)Zn_(1-x)Ni_(x)O_(4)solid solution samples exhibited good CO_(2)chemisorption efficiencies,similarly to the pristine Li_(6)ZnO_(4)chemisorption trends observed.Moreover,a kinetic analysis of CO_(2)isothermal chemisorptions,using the Avrami-Erofeev model,evidenced an increment of the constant rates as a function of the Ni content.Since Ni^(2+)ions incorporation did not reduce the CO_(2)capture efficiency and kinetics,the catalytic properties of thesematerialswere evaluated in the DRM process.Results demonstrated that nickel ions favored hydrogen(H_(2))production over the pristine Li_(6)ZnO_(4)phase,despite a second H2 production reaction was determined,methane decomposition.Thereby,Li_(6)Zn_(1-x)Ni_(x)O_(4)ceramics can be employed as bifunctional materials.
基金financially supported by the Joint Fund of Coal, set up by National Natural Science Foundation of China and Shenhua Co., Ltd.(U1261104)the National Natural Science Foundation of China (21276041)+3 种基金the Program for New Century Excellent Talents in University (NCET-12-0079)the Natural Science Foundation of Liaoning Province (2015020200)the Fundamental Research Funds for the Central Universities (DUT15LK41)the Science and Technology Development Program of Hangzhou (20130533B14)~~
文摘An immature pinecone shaped hierarchically structured zirconia （ZrO2-ipch） and a cobblestone-like zirconia nanoparticulate （ZrO2-cs）, both with the monoclinic phase （m-phase）, were synthesized by the facile hydrothermal method and used as the support for a Ni catalyst for the dry reforming of methane （DRM） with CO2. ZrO2-ipch is a much better support than ZrO2-cs and the traditional ZrO2 irregular particles made by a simple precipitation method （ZrO2-ip）. The supported Ni catalyst on ZrO2-ipch （Ni/ZrO2-ipch） exhibited outstanding catalytic activity and coke-resistant stability compared to the ones on ZrO2-cs （Ni/ZrO2-cs） and ZrO2-ip （Ni/ZrO2-ip）. Ni/ZrO2-ip exhibited the worst catalytic performance. The origin of the significantly enhanced catalytic performance was revealed by characterization including XRD, N2 adsorption measurement （BET）, TEM, H2-TPR, CO chemisorption, CO2-TPD, XPS and TGA. The superior catalytic activity of Ni/ZrO2-ipch to Ni/ZrO2-cs or Ni/ZrO2-ip was ascribed to a higher Ni dispersion, increased reducibility, enhanced oxygen mo- bility, and more basic sites with a higher strength, which were due to the unique hierarchically structural morphology of the ZrO2-ipch support. Ni/ZrO2-ipch exhibited better stability for the DRM reaction than Ni/ZrO2-ip, which was ascribed to its higher resistance to Ni sintering due to a strengthened metal-support interaction and the confinement effect of the mesopores and coke deposition resistance. The higher coking resistance of Ni/ZrO2-ipch for the DRM reaction in comparison with Ni/ZrOz-ip orignated from the coke-removalabitity of the higher amount of lattice oxygen and more basic sites, confirmed by XPS and CO2-TPD analysis, and the stabilized Ni on the Ni/ZrO2-ipch catalyst by the confinement effect of the mesopores of the hierarchical ZrO2-ipch sup- port. The superior catalytic performance and coking resistance of the Ni/ZrO2-ipch catalyst makes it a promising candidate for synthesis gas production from the DRM reaction.
基金supported by the National Natural Science Foundation of China (21567016, 21566022, 21263015)the Natural Science Foundation of Jiangxi Province (20151BBE50006, 20151BAB203024)the Education Department of Jiangxi Province (KJLD14005, GJJ150016)
文摘In this study, Ni/YZrOcatalysts prepared with impregnation method and treated by dielectric barrier discharge plasma(DBD) in different atmospheres have been investigated for methane dry reforming. It is revealed by H-TPR that plasma treatment can enhance the interaction between Ni O/Ni particles and the YZrOpyrochlore support. Therefore, catalysts with smaller Ni O and Ni grains sizes, higher metallic Ni active surface areas can be achieved, as evidenced by XRD, TEM and Hadsorption-desorption measurements. As a consequence, the plasma-treated catalysts show significantly improved activity, stability and coke resistance, as testified by the TEM and TGA-DSC results. Plasma treatment in H/Ar gas mixture is found to be the best condition to prepare Ni/YZrO, which can be used to obtain a catalyst with the highest activity, stability and most potent coke resistance. It is believed that the smaller Ni grain size and higher metallic Ni active surface area induced by plasma treatment are the inherent reasons accounting for the promoted reaction performance of the Ni/YZrOpyrochlore catalysts.
基金financial supports from the Zhejiang Normal University(YS304320035)the Natural Science Foundation of China(21603039)。
文摘Supported nickel catalysts are promising candidates for dry reforming of methane, but agglomeration of Ni^(0) and coke deposition hinder the industrial applications. Herein, we report a novel interface-directed synthetic approach to construct distinct metal ensembles by carefully tuning the compositions of the carriers. A Zr-Mn-Zn ternary oxide-supported Ni catalyst, together with the respective binary oxide-supported analogues, was synthesized by adopting a sequential co-precipitation and wetness impregnation method. Combined characterization techniques identify distinct catalyst models, including (i) conventional NiO nanoparticles with different sizes on Zr-Mn and Zr-Zn, and (ii) epitaxially growing NiO ensembles of a few nanometers thickness at the periphery of ZnO_(x) particles. These catalysts exhibit divergent responses in the catalytic testing, with the ternary oxide system significantly outperforming the binary analogues. The strong electronic interactions between Mn-Ni increase Ni dispersion and the activity while the stability is strengthened upon Zn addition. Both high activity, high selectivity, and remarkable stability are attained upon co-adding Mn and Zn. The interfaces between Ni and Zr-Mn-Zn rather than the physical contacts of individual oxide-supported analogues through mechanical mixing are keys for the outstanding performance.
文摘In this study, the use of a thermally stable Ir/Ce0.9La0.1O2 catalyst was investigated for the dry reforming of methane. The doping of La203 into the CeO2 lattice enhanced the chemical and physical properties of the Ir/Ce0.9La0.1O2 catalyst, such as redox properties, Ir dispersion, oxygen storage capacity, and thermal stability, with respect to the Ir/CeO2 catalyst. Hence, the Ir/Ce0.9La0.1O2 catalyst exhibits higher activity and stabler performance for the dry reforming of methane than the Ir/CeO2 catalyst. This observation can be mainly attributed to the stronger interaction between the metal and support in the Ir/Ce0.9La0.1O2 catalyst stabilizing the catalyst structure and improving the oxygen storage capacity, leading to negligible aggregation of Ir nanoparticles and the Ce0.9La0.1O2 support at high temperatures, as well as the rapid removal of carbon deposits at the boundaries between the Ir metal and the Ce0.9La0.1O2 support.
基金supported by the National Natural Science Foundation of China(11075113)
文摘Ni-Co bimetallic catalysts with different Ni/Co content were derived from cold plasma jet decomposition and reduction of hydrotalcite-like compounds containing Ni,Co,Mg and Al,and their catalytic performance was investigated with dry reforming of methane.Experimental results showed that the hydrotalcite-like precursors could be completely decomposed and partly reduced by cold plasma jet,and the Nicontained catalysts exhibited much higher activity than the catalyst without Ni.Especially,the catalyst with Ni/Co ratio of 8/2 achieved not only the highest conversions of 80.3%and 69.3%for CH4 and CO2,respectively,but also the best stability in 100 h testing.The catalysts were characterized by XRD,XPS,TEM and N2 adsorption techniques,and the results showed that the better performance of the 8Ni2Co bimetallic catalyst was attributed to its higher metal dispersion,smaller metal particle size,as well as the interaction effect between Ni and Co,which were brought by the special catalyst preparation method.
