The hot deformation characteristics of as-forged Ti−3.5Al−5Mo−6V−3Cr−2Sn−0.5Fe−0.1B−0.1C alloy within a temperature range from 750 to 910℃and a strain rate range from 0.001 to 1 s^(-1) were investigated by hot compre...The hot deformation characteristics of as-forged Ti−3.5Al−5Mo−6V−3Cr−2Sn−0.5Fe−0.1B−0.1C alloy within a temperature range from 750 to 910℃and a strain rate range from 0.001 to 1 s^(-1) were investigated by hot compression tests.The stress−strain curves show that the flow stress decreases with the increase of temperature and the decrease of strain rate.The microstructure is sensitive to deformation parameters.The dynamic recrystallization(DRX)grains appear while the temperature reaches 790℃at a constant strain rate of 0.001 s^(-1) and strain rate is not higher than 0.1 s^(-1) at a constant temperature of 910℃.The work-hardening rateθis calculated and it is found that DRX prefers to happen at high temperature and low strain rate.The constitutive equation and processing map were obtained.The average activation energy of the alloy is 242.78 kJ/mol and there are few unstable regions on the processing map,which indicates excellent hot workability.At the strain rate of 0.1 s^(-1),the stress−strain curves show an abnormal shape where there are two stress peaks simultaneously.This can be attributed to the alternation of hardening effect,which results from the continuous dynamic recrystallization(CDRX)and the rotation of DRX grains,and dynamic softening mechanism.展开更多
Profound and comprehensive investigations on the morphology characteristics ofαprecipitates are essential for the microstructural control of metastableβtitanium alloys.At the very beginning of aging treatment,intrag...Profound and comprehensive investigations on the morphology characteristics ofαprecipitates are essential for the microstructural control of metastableβtitanium alloys.At the very beginning of aging treatment,intragranularαprecipitates with a dot-like morphology begin to generate nearby the dislocations,then those dot-likeαprecipitates with the same crystallographic orientation tend to connect with each other to develop a lath-like morphology.With the progress of aging treatment,the orientated lath-likeαprecipitates gradually combine with each other to form the V-shaped clusters or the triangular ones.The dislocations of{110}_(β)<111>βedge type are evidenced within theβgrains,and it is found that variant selection ofαprecipitates induced by the transformation strain and the interplay betweenαvariants and the dislocations are confirmed as the key factors for the formation of the V-shaped or triangular clusters.The results of this work could provide underlying knowledge on the morphology characteristics of intraguranularαprecipitates related to the crystal defects and the strain accommodation ofαvariants in metastableβtitanium alloys.展开更多
Microstructural evolution and deformation mechanism of a metastableβalloy(Ti-10 V-2 Fe-3 Al)processed by rotationally accelerated shot peening(RASP)were systematically investigated with optical microscopy,X-ray diffr...Microstructural evolution and deformation mechanism of a metastableβalloy(Ti-10 V-2 Fe-3 Al)processed by rotationally accelerated shot peening(RASP)were systematically investigated with optical microscopy,X-ray diffraction,electron backscatter diffraction and transmission electron microscopy.Different gradient hierarchical microstructures(gradients inα″martensite andβphase,and hierarchical twins range from the nanoscale to microscale)can be fabricated by RASP via changing the shot peening time.The hardening behavior and tensile mechanical properties of gradient hierarchical microstructure were systematically explored.Novel deformation twinning systems of{112}α″and{130}<310>α″in the kinkedα″martensite were revealed during the tensile deformation.It was found that stress-induced martensitic transformation,twinnedα″martensite and the related dynamic grain refinement contribute to hardness and work hardening ability.Simultaneous improvement of strength and ductility of the metastableα″titanium alloy can be achieved by introducing a gradient hierarchical microstructure.展开更多
To overcome the strength-plasticity trade-offin the structural titanium alloys,a novel metastableβti-tanium alloy Ti-5Mo-4Cr-1V-1Zr(Ti-5411)with high strength and high plasticity was designed by the d-electrons theor...To overcome the strength-plasticity trade-offin the structural titanium alloys,a novel metastableβti-tanium alloy Ti-5Mo-4Cr-1V-1Zr(Ti-5411)with high strength and high plasticity was designed by the d-electrons theory,average electron-to-atom ratio(e/α^(-))and atomic radius difference(Δr^(-))theory.Com-bined in-situ scanning electron microscope(SEM)and electron backscatter diffraction(EBSD),the defor-mation mechanisms of the novel Ti-5411 metastableβtitanium alloy were systematically investigated.The results show that the Ti-5411 alloy exhibits excellent yield strength(∼689 MPa),tensile strength(∼930 MPa)and total elongation(∼39%).The in-situ tension indicates that slip activities,crystal rota-tion,stress induced martensite(SIM)α''transformation and{332}<113>deformation twin are the major deformation mechanisms of Ti-5411 alloy.Besides,with the increase of strain degree(0-0.5 mm displace-ment),deformation twins increase,widen and interlace.At 0.35 mm tensile displacement,the orientation of theβgrains rotates∼6.65°to accommodate the increased macrostrain.Additionally,martensiteα''also assists the nucleation of twins.Some{332}<113>twins grow and merge by consuming martensiteα''during deformation,and the residual martensiteα''remains in the merged twins.展开更多
The effect of hot deformation onα-phase precipitation during the subsequent heat treatment,as well as the mechanical properties of TB18 Ti-alloy,was investigated.Results show that the round bar obtained by the dual-p...The effect of hot deformation onα-phase precipitation during the subsequent heat treatment,as well as the mechanical properties of TB18 Ti-alloy,was investigated.Results show that the round bar obtained by the dual-phase field forging of the cast ingot exhibits uniform composition distribution on its cross-section.However,various degrees of deformation are detected at different positions on the cross-section,which is attributed to the characteristics of the forging process.Under the forging condition,the microstructure is mainly composed ofβ-phase matrix and coarsened discontinuous primaryα-phases.After solution and following artificial aging treatment,the primaryα-phases disappear,while needle-like secondaryα-phases precipitate in the matrix.Additionally,dispersed white zones are observed in the samples after aging,which are analyzed to be the precipitation-free zones of secondaryα-phase.Despite a uniform compositional distribution among various regions,these dispersed white zones exhibit higher content and larger size in the positions that have undergone lower forging deformation.It indicates that the insufficient forging deformation inhibits the precipitation of the secondaryα-phase,ultimately resulting in the lower strengthening effect by heat treatment.Thus,consistent with the characteristics of the forging process,a periodic variation of sample in strength is detected along the circumferential direction of the forged round bar.展开更多
High porosity and high brittleness are the main reasons that limit the long-term service life of the alumina-titanium oxide composite coating.Herein,a metastable nanostructured aluminatitanium oxide composite coating ...High porosity and high brittleness are the main reasons that limit the long-term service life of the alumina-titanium oxide composite coating.Herein,a metastable nanostructured aluminatitanium oxide composite coating with high density and high properties was synthesized by plasma spraying of TiO_(2)-Al composite powder.The main phases of the metastable nanostructured alumina-titanium oxide wereγ-Al_(2)O_(3),TiO and AlTiO_(2).The coating,as prepared,contains various metastable microstructures,such as fine-grained,intra-/inter-granular,and"self-locking"microstructures.These metastable microstruc-tures are important for the improvement of hardness and toughness of the coating.Compared with other alumina-based composite coatings,the metastable nanostructured aluminatitanium oxide composite coating showed the most impressive overall performance.The reinforcing and toughening mechanism of the metastable alumina-titanium oxide composite coating included fine grain strengthening and self-toughening of the metastable microstructure.展开更多
In order to investigate the damage tolerance of a metastable Ti-5Al-3V-3Mo-2Cr-2Zr-1Nb-1Fe(Ti5321)alloy with bimodal microstructure using void growth quantification and micromechanical modeling,in situ tensile testing...In order to investigate the damage tolerance of a metastable Ti-5Al-3V-3Mo-2Cr-2Zr-1Nb-1Fe(Ti5321)alloy with bimodal microstructure using void growth quantification and micromechanical modeling,in situ tensile testing was performed during X-ray microtomography experiments.Compared with investigations of surface voids by traditional two-dimensional(2D)methods involving post-mortem characterization,three-dimensional(3D)information on void evolution inside optically opaque samples obtained through X-ray microtomography is essential.The Rice and Tracey model and Huang model were applied to predict void growth and show good agreement with experimental data using calibration of the damage parameterα.The void growth kinetics of Ti5321 with bimodal microstructure was analyzed by comparing theαvalue with that of Ti64 for different microstructure morphologies.The damage mechanism of ductile fracture of Ti5321 with bimodal microstructure is discussed.It was found that the size of the voids apparently increases with the triaxiality of stress.Post-mortem scanning electron microscopy(SEM)was also used to demonstrate this damage mechanism of ductile fracture of Ti5321.展开更多
Metastable β-Ti alloys exhibiting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) generally have excellent ductility, but typically at the expense of relatively low yield strengths whi...Metastable β-Ti alloys exhibiting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) generally have excellent ductility, but typically at the expense of relatively low yield strengths which has restricted their widespread use. Our work shows that interstitial oxygen can be employed to regulate β phase stability to significantly enhance both strength and ductility of TWIP/TRIP alloys. For a Ti-32Nb wt.% base alloy, inclusion of 0.3 wt.% O enhanced ductility by more than 140 %, reaching up to 54 % strain, and improved the tensile yield strength by over 95 % to 632 MPa. Compared to other common engineering alloys such as Ti-45Nb, elongation was increased by 29 %, and the yield strength increased by 182 MPa, respectively. Here, we elucidate on impacts of oxygen doping on TWIP/TRIP behaviors in the Ti-32Nb alloy. We reveal that oxygen regulates the critical stress for martensitic transformation, twinning, and dislocation slip. At lower oxygen doping concentrations (≤0.3 wt.% O), multi-stage martensitic transformation and martensitic twinning resulted in high ductility. In higher oxygen content alloys (≥0.5 wt.% O), deformation occurred initially via twinning, while strain induced martensite was subsequently induced in retained β phase regions. Oxygen concentrations control the deformation mechanisms, providing a flexible means to synergistically balance an alloy's strength and ductility. The use of oxygen to enhance stability of the β phase and regulate deformation behaviors is a promising new approach for creating high-performance TWIP/TRIP metastable β-Ti alloys with outstanding mechanical properties.展开更多
Thermomechanical processing(TMP)is especially crucial for metastableβtitanium alloys,which has received significant attention in the community for a long time.In this contribution,the processing-responding behaviour ...Thermomechanical processing(TMP)is especially crucial for metastableβtitanium alloys,which has received significant attention in the community for a long time.In this contribution,the processing-responding behaviour including microstructure evolution process,texture variation mechanism,and un-derlying deformation process of powder metallurgy Ti-5553 alloy in a wide processing parameter range was comprehensively investigated.Thermal physical simulation was performed on the alloy at temper-atures ranging from 800℃ to 1100℃,and strain rates between 0.001 s^(−1) and 10 s^(−1),to varied defor-mation degrees of 20%-80%height reduction.It was found that the processing parameters(i.e.temper-ature,strain rate,and deformation degree)are influential on the deformation process and resultant mi-crostructure.Varied microstructural evolution processes forβphase including flow localization,dynamic recovery,dynamic recrystallization,and grain coarsening are activated in different processing domains,while different evolution mechanisms forαphase including dynamic precipitation,phase separation,dy-namic coarsening,and mechanical shearing also play their roles under different processing conditions.In particular,four exceptional evolution mechanisms ofαprecipitation which have not been previously reported in titanium alloys were discovered and clearly demonstrated,more specifically,they are multi-interior twinning,internal compositing,layered coarsening and selective diffusion-actuated separation.After the establishment of comprehensive microstructural evolution mechanism maps,the guidance for precise processing and the knowledge reserve extension for deformation process of metastableβtita-nium alloys can be effectively achieved.展开更多
In this work,the effect of microstructure features on the high-cycle fatigue behavior of Ti-7Mo-3Nb-3Cr-3Al(Ti-7333)alloy is investigated.Fatigue tests were carried out at room temperature in lab air atmosphere using ...In this work,the effect of microstructure features on the high-cycle fatigue behavior of Ti-7Mo-3Nb-3Cr-3Al(Ti-7333)alloy is investigated.Fatigue tests were carried out at room temperature in lab air atmosphere using a sinusoidal wave at a frequency of 120 Hz and a stress ratio of 0.1.Results show that the fatigue strength is closely related to the microstructure features,especially theα_(p) percentage.The Ti-7333 alloy with a lowerα_(p) percentage exhibits a higher scatter in fatigue data.The bimodal fatigue behavior and the duality of the S-N curve are reported in the Ti-7333 alloy with relatively lowerα_(p) percentage.Crack initiation region shows the compoundα_(p)/βfacets.Facetedα_(p) particles show crystallographic orientation and morphology dependence characteristics.Crack-initiation was accompanied by faceting process across elongatedα_(p) particles or multiple adjacentα_(p) particles.These particles generally oriented for basal slip result in near basal facets.Fatigue crack can also initiate at elongatedα_(p) particle well oriented for prismatic slip.Theβfacet is in close correspondence to{110}or{112}plane with high Schmid factor.Based on the fracture observation and FIB-CS analysis,three classes of fatigue-critical microstructural configurations are deduced.A phenomenological model for the formation ofα_(p) facet in the bimodal microstructure is proposed.This work provides an insight into the fatigue damage process of theβprecipitate strengthened metastableβtitanium alloys.展开更多
To study the relationship between the microstructure and tensile properties of the novel metastable β titanium alloy Ti-5.5Cr-5Al-4Mo-3Nb-2Zr,a heat treatment process of ABFCA(solid solution in α+βregion with subse...To study the relationship between the microstructure and tensile properties of the novel metastable β titanium alloy Ti-5.5Cr-5Al-4Mo-3Nb-2Zr,a heat treatment process of ABFCA(solid solution in α+βregion with subsequent furnace cooling followed by aging treatment finally)was designed,by which α phases of different sizes can be precipitated in the β matrix.The results show that the microstructure obtained by this heat treatment process is composed of primary α(α_(p))phase,submicro rod-like α(α_(r))phase and secondary α(α_(s))phase.The alloy with multi-scale α phase has an excellent balance between strength and ductility.The elongation is about 18.3% at the ultimate tensile strength of 1125.4 MPa.The relationship between the strength of the alloy and the α phase was established.The strength of the alloy is proportional to the power of‒1/2 of the average spacing and width of α phase.The α_(s) phase with a smaller size and phase spacing can greatly improve the strength of the alloy by hindering dislocation slip.The transmission electron microscope analysis shows that there is a large amount of dislocation accumulation at the α/β interfaces,and many deformation twins are found in the α_(p) phase after tensile deformation.When the dislocation slip is hindered,twins occur at the stress concentration location,and twins can initiate some dislocations that are difficult to slip.Meanwhile,the plastic strain is distributed uniformly among the α_(p),α_(r),α_(s) phases and β matrix,thereby enhancing the ductility of the alloy.展开更多
A new metastable β type titanium alloy called TB-13 with the combination of excellent strength and ductility was developed successfully.In order to develop a perspective on this new alloy,the influence of several com...A new metastable β type titanium alloy called TB-13 with the combination of excellent strength and ductility was developed successfully.In order to develop a perspective on this new alloy,the influence of several commonly used heat treatments on the microstructure and properties was studied.In solution-treated and quenched samples,a low-temperature aging at 480°C results in the precipitation of finerαphase.The precipitation of coarserαphase plate at higher aging temperature(560°C)leads to the increase of tensile ductility but reduction of strength.During low-temperature aging at 300°C,quite homogeneous distribution of fine isothermalωphase particles was found.The isothermalωphase provides nucleation sites forαphase during two-step aging process and makesαphase extremely fine and disperse uniformly in β matrix.Thus,TB-13 alloy is strengthened and its mechanical properties are improved.展开更多
The constitutive model was developed to describe the relationship among flow stress,strain,strain rate,and deformation temperature completely,based on the characteristics of flow stress curves for a new kind of metast...The constitutive model was developed to describe the relationship among flow stress,strain,strain rate,and deformation temperature completely,based on the characteristics of flow stress curves for a new kind of metastable β Ti2448 titanium alloy from isothermal hot compression tests,in a wide range of temperatures（1023-1123 K） and strain rates（63-0.001 s-1）.During this process,the adopted hyperbolic sine function based on the unified viscoplasticity theory was used to model the flow behavior of alloy undergoing flow softening caused by dynamic recovery（DRV） at high strain rates（≥1 s-1）.The standard Avrami equation was adopted to represent the softening mechanism attributed to dynamic recrystallization（DRX） at low strain rates（1 s-1）.Additionally,the material constants were determined by optimization strategy,which is a new method to solve the nonlinear constitutive equation.The stress—strain curves predicted by the developed constitutive model agree well with the experimental results,which con-rms that the developed constitutive model can give an accurate estimate of the-ow stress of Ti2448 titanium alloy and provide an effective method to model the flow behavior of metastable β titanium alloys during hot deformation.展开更多
The compressive yielding phenomenon of titanium alloys is not as focused and sufficiently ascertain as the tensile yielding phenomenon.In the present work,the peculiar compressive yielding behavior and the different d...The compressive yielding phenomenon of titanium alloys is not as focused and sufficiently ascertain as the tensile yielding phenomenon.In the present work,the peculiar compressive yielding behavior and the different dynamic responses of three different initial microstructures(singleβ,clavateβand lamellarβ)were investigated in an attractive metastableβtitanium alloy Ti-5553 using electron microscopes/crystallographic calculation/crystal plastic finite element simulation.Results reveal that the distinct compressive yielding behavior,steep peaks of sudden drop in the initial stage(very small true strain 0.03)of stress loading have appeared in the compression stress-strain curves except for the lamellarβinitial microstructure.Dislocation slip is the essential mechanism of the initial yielding behavior.Interlaced multiple-slip bands formed in the singleβinitial microstructure during the warm deformation process.A small quantity of single slip bands was observed in the deformed clavateβinitial microstructure.The abundant varied nano/ultrafineβsprecipitates were nucleated dynamically and dispersedly in all the three deformed initial microstructures.The multiple-slip bands formation and substantial nanoscaleβsresult in the highest peak of flow stress for singleβinitial microstructure.The compressive slip bands are formed early in the elastic–plastic deformation stage.As the increasing strain,the sample showed a significant compressive bulge,or eventually forming a strong adiabatic shear band or crack.These results are expected to provide a reference for the study of deformation behavior and mechanical properties of metastableβtitanium alloys.展开更多
It is well accepted that grain-boundary phases in metallic alloys greatly deteriorate the mechanical properties.In our work,we report on a novel strategy to prepare high strength-ductility β-type(Ti69.71 Nb23.72Zr4.8...It is well accepted that grain-boundary phases in metallic alloys greatly deteriorate the mechanical properties.In our work,we report on a novel strategy to prepare high strength-ductility β-type(Ti69.71 Nb23.72Zr4.83Ta1.74)97Si3(at.%)(TNZTS) alloys by tailoring grain-boundary metastable Si-containing phase.Specifically,the thin shell-shaped metastable S1 phase surrounding the columnar β-Ti grain was intercepted successfully via nonequilibrium rapid solidification achieved by selective laser melting(SLM).Subsequently,the thin shell-shaped metastable(Ti,Nb,Zr)5 Si3(called S1) phase was transformed into globular(Ti,Nb,Zr)2 Si(called S2) phase by the solution heat treatment.Interestingly,the globular S2 phases reinforced TNZTS alloy exhibits ultrahigh yield strength of 978 MPa,ultimate strength of 1010 MPa and large elongation of 10.4 %,overcoming the strength-ductility trade-off of TNZTS alloys by various methods.Especially,the reported yield strength herein is 55 % higher than that of conventionally forged TNZT alloys.Dynamic analysis indicates the globularization process of the metastable S1 phase is controlled by the model of termination migration.The quantitative analysis on strengthening mechanism demonstrates that the increase in yield strength of the heat-treated alloys is mainly ascribed to the strengthening of the precipitated silicide and the dislocations induced by high cooling rate.The obtained results provide some basis guidelines for designing and fabricating β-titanium alloys with excellent mechanical properties,and pave the way for biomedical application of TNZTS alloy by SLM.展开更多
This study investigates the development of novel high-entropy alloys(HEAs)with enhanced mechanical properties through an innovative fabrication method of direct energy deposition(DED).The focus is on the creation of m...This study investigates the development of novel high-entropy alloys(HEAs)with enhanced mechanical properties through an innovative fabrication method of direct energy deposition(DED).The focus is on the creation of metastable core-shell precipitation-strengthened HEAs that exhibit a unique multi-stage terrace-like slip wave toughening mechanism,a novel approach to improving both strength and ductility simultaneously.Mechanical testing reveals that the developed HEAs exhibit superior mechanical proper-ties,including high yield strength,ultimate tensile strength,and exceptional ductility.The improvement in these properties is attributed to the multi-stage terrace-like slip wave toughening mechanism activated by the unique microstructural features.This toughening mechanism involves the sequential activation of slip systems,facilitated by the stress concentration around the core-shell precipitates and the subsequent propagation of slip waves across the material.The terrace-like pattern of these slip waves enhances the material's ability to deform plastically,providing a significant toughening effect while maintaining high strength levels.Furthermore,the study delves into the fundamental interactions between the microstruc-tural elements and the deformation mechanisms.It elucidates how the core-shell precipitates and the matrix cooperate to distribute stress uniformly,delay the onset of necking,and prevent premature failure.This synergistic interaction between the microstructural features and the slip wave toughening mecha-nism is central to the remarkable balance of strength and ductility achieved in the HEAs.The introduction of a multi-stage terrace-like slip wave toughening mechanism offers a new pathway to designing HEAs with an exceptional amalgamation of strength and ductility.展开更多
β titanium alloys with bi-modal structure which exhibit improved strength-ductility combination and fatigue property are widely used in aviation and aerospace industry.However,owing to the small size of primary α(α...β titanium alloys with bi-modal structure which exhibit improved strength-ductility combination and fatigue property are widely used in aviation and aerospace industry.However,owing to the small size of primary α(αp) and nano-scaled multi variant distribution of secondary α platelets(αs),investigating the deformation behavior is really a challenging work.In this work,by applying transmission electron microscopy(TEM),the slip behavior in αp and transformed β matrix with different tensile strain was studied.After α/β solution treatment,the initial dislocation slips on {110} plane with <1 1 1> direction in β matrix.During furtherdeformation,(110),(101) and(1 1 2) multi slip is generated which shows a long straight cro s sing configuration.Dislocation cell is exhibited in β matrix at tensile strain above 20 %.Diffe rent from the solid solution treated sample,high density wavy dislocations are generated in transformedβ matrix.High fraction fine as hinders dislocation motion in β matrix effectively which in turn dominates the strength of the alloy.In primary α phase(αp),a core-shell structure is formed during deformation.Both pyramidal a+c slip and prismatic/basal a slip are generated in the shell layer.In core region,plastic deformation is governed by prismatic/basal a slip.Formation of the core-shell structure is the physical origin of the improved ductility.On one hand,the work hardening layer(shell) improves the strength of αp,which could deform compatibly with the hard transformed β matrix.Meanwhile,the center area(core) deforms homogeneously which will sustain plastic strain effectively and increase the ductility.This paper studies the slip behavior and reveals the origin of the improved strength-ductility combination in Bi-modal structure on a microscopic way,which will give theoretical advises for developing the next generation high strength β titanium alloys.展开更多
The effect of die forging on the microstructure evolution and deformation behavior of metastable β-titanium alloy Ti55511 was investigated by electron backscatter diffraction.Before die forging,the alloy Ti55511 was ...The effect of die forging on the microstructure evolution and deformation behavior of metastable β-titanium alloy Ti55511 was investigated by electron backscatter diffraction.Before die forging,the alloy Ti55511 was subjected to multi-pass forging to optimize the microstructural heterogeneity(texture)which can cause mechanical behavior anisotropy of titanium alloys.Results show that after die forging,Ti55511 components exhibit different microstructures and textures in different local areas.No<100>fiber texture is found in all areas with different degrees of deformation.Dynamic recrystallization occurs in the area where large strain occurs during the early stage of die forging.Basket-weave microstructure forms in most local areas.展开更多
The influence of thermo-mechanical processing (TMP) on the microstructure and the electrochemical behavior of new metastableβ alloy Ti?20.6Nb?13.6Zr?0.5V (TNZV) was investigated. The TMP included hot working in below...The influence of thermo-mechanical processing (TMP) on the microstructure and the electrochemical behavior of new metastableβ alloy Ti?20.6Nb?13.6Zr?0.5V (TNZV) was investigated. The TMP included hot working in belowβ transus, solution heat treatments at the same temperature and different cooling rates in addition to aging. Depending upon the TMP conditions, a wide range of microstructures with varying spatial distributions and morphologies of equiaxed/elongatedα andβ phases were attained, allowing for a wide range of electrochemical properties to be achieved. The corrosion behavior of the studied alloy was evaluated in a Ringer’s solution at 37 °C via open circuit potential?time and potentiodynamic polarization measurements.展开更多
Influence of severe cold deformation of titanium alloy Ti-1.5%A1-6.8%Mo-4.5%Fe in metastable β condition on the evolution of phase composition, microstructure, and tensile properties during continuous rapid heating w...Influence of severe cold deformation of titanium alloy Ti-1.5%A1-6.8%Mo-4.5%Fe in metastable β condition on the evolution of phase composition, microstructure, and tensile properties during continuous rapid heating was studied. As-deformed alloy was characterized by quasi-amorphous single-phase β condition with an abnormal temperature dependence of electric resistance that was normalized after 48 h exposure at room temperature as a result of isothermal ω phase precipitation. Subsequent rapid heating with a rate of 5 ℃/s caused recovery and recrystallization. Tensile properties of the alloy after different treatments were determined and discussed.展开更多
文摘The hot deformation characteristics of as-forged Ti−3.5Al−5Mo−6V−3Cr−2Sn−0.5Fe−0.1B−0.1C alloy within a temperature range from 750 to 910℃and a strain rate range from 0.001 to 1 s^(-1) were investigated by hot compression tests.The stress−strain curves show that the flow stress decreases with the increase of temperature and the decrease of strain rate.The microstructure is sensitive to deformation parameters.The dynamic recrystallization(DRX)grains appear while the temperature reaches 790℃at a constant strain rate of 0.001 s^(-1) and strain rate is not higher than 0.1 s^(-1) at a constant temperature of 910℃.The work-hardening rateθis calculated and it is found that DRX prefers to happen at high temperature and low strain rate.The constitutive equation and processing map were obtained.The average activation energy of the alloy is 242.78 kJ/mol and there are few unstable regions on the processing map,which indicates excellent hot workability.At the strain rate of 0.1 s^(-1),the stress−strain curves show an abnormal shape where there are two stress peaks simultaneously.This can be attributed to the alternation of hardening effect,which results from the continuous dynamic recrystallization(CDRX)and the rotation of DRX grains,and dynamic softening mechanism.
基金the Science and Technology Major Project of Shanxi Province(Nos.20191102008 and 20181101014)the Applied Basic Research Foundation of Shanxi Province(Nos.201901D211255 and 201901D211256)+4 种基金Platform and Talent Project of Shanxi Province(No.201805D211036)Guiding Local Science and Technology Development Projects by the Central Government(No.YDZX20191400002796)Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi(No.2020L0304)Key projects of Equipment Pre-research Foundation(No.61409230407)the Natural Science Research Project of NUC(No.XJJ201916)。
文摘Profound and comprehensive investigations on the morphology characteristics ofαprecipitates are essential for the microstructural control of metastableβtitanium alloys.At the very beginning of aging treatment,intragranularαprecipitates with a dot-like morphology begin to generate nearby the dislocations,then those dot-likeαprecipitates with the same crystallographic orientation tend to connect with each other to develop a lath-like morphology.With the progress of aging treatment,the orientated lath-likeαprecipitates gradually combine with each other to form the V-shaped clusters or the triangular ones.The dislocations of{110}_(β)<111>βedge type are evidenced within theβgrains,and it is found that variant selection ofαprecipitates induced by the transformation strain and the interplay betweenαvariants and the dislocations are confirmed as the key factors for the formation of the V-shaped or triangular clusters.The results of this work could provide underlying knowledge on the morphology characteristics of intraguranularαprecipitates related to the crystal defects and the strain accommodation ofαvariants in metastableβtitanium alloys.
基金supported financially by the Scientific Challenge Project of China(No.TZ2018001)the National Natural Science Foundation of China(No.11627901)。
文摘Microstructural evolution and deformation mechanism of a metastableβalloy(Ti-10 V-2 Fe-3 Al)processed by rotationally accelerated shot peening(RASP)were systematically investigated with optical microscopy,X-ray diffraction,electron backscatter diffraction and transmission electron microscopy.Different gradient hierarchical microstructures(gradients inα″martensite andβphase,and hierarchical twins range from the nanoscale to microscale)can be fabricated by RASP via changing the shot peening time.The hardening behavior and tensile mechanical properties of gradient hierarchical microstructure were systematically explored.Novel deformation twinning systems of{112}α″and{130}<310>α″in the kinkedα″martensite were revealed during the tensile deformation.It was found that stress-induced martensitic transformation,twinnedα″martensite and the related dynamic grain refinement contribute to hardness and work hardening ability.Simultaneous improvement of strength and ductility of the metastableα″titanium alloy can be achieved by introducing a gradient hierarchical microstructure.
基金supported by the National Natural Science Foundation of China(Nos.52104372,52374332)the Postdoctoral Research Foundation of China(Nos.2019M651129,2019TQ0053)the Fundamental Research Funds for the Central Universities(No.N2324003-02).
文摘To overcome the strength-plasticity trade-offin the structural titanium alloys,a novel metastableβti-tanium alloy Ti-5Mo-4Cr-1V-1Zr(Ti-5411)with high strength and high plasticity was designed by the d-electrons theory,average electron-to-atom ratio(e/α^(-))and atomic radius difference(Δr^(-))theory.Com-bined in-situ scanning electron microscope(SEM)and electron backscatter diffraction(EBSD),the defor-mation mechanisms of the novel Ti-5411 metastableβtitanium alloy were systematically investigated.The results show that the Ti-5411 alloy exhibits excellent yield strength(∼689 MPa),tensile strength(∼930 MPa)and total elongation(∼39%).The in-situ tension indicates that slip activities,crystal rota-tion,stress induced martensite(SIM)α''transformation and{332}<113>deformation twin are the major deformation mechanisms of Ti-5411 alloy.Besides,with the increase of strain degree(0-0.5 mm displace-ment),deformation twins increase,widen and interlace.At 0.35 mm tensile displacement,the orientation of theβgrains rotates∼6.65°to accommodate the increased macrostrain.Additionally,martensiteα''also assists the nucleation of twins.Some{332}<113>twins grow and merge by consuming martensiteα''during deformation,and the residual martensiteα''remains in the merged twins.
基金Qin Chuangyuan Cites High-Level Innovation,Entrepreneurship Talent Project(QCYRCXM-2023-003)Innovation Capability Support Program of Shaanxi(2022KJXX-84)。
文摘The effect of hot deformation onα-phase precipitation during the subsequent heat treatment,as well as the mechanical properties of TB18 Ti-alloy,was investigated.Results show that the round bar obtained by the dual-phase field forging of the cast ingot exhibits uniform composition distribution on its cross-section.However,various degrees of deformation are detected at different positions on the cross-section,which is attributed to the characteristics of the forging process.Under the forging condition,the microstructure is mainly composed ofβ-phase matrix and coarsened discontinuous primaryα-phases.After solution and following artificial aging treatment,the primaryα-phases disappear,while needle-like secondaryα-phases precipitate in the matrix.Additionally,dispersed white zones are observed in the samples after aging,which are analyzed to be the precipitation-free zones of secondaryα-phase.Despite a uniform compositional distribution among various regions,these dispersed white zones exhibit higher content and larger size in the positions that have undergone lower forging deformation.It indicates that the insufficient forging deformation inhibits the precipitation of the secondaryα-phase,ultimately resulting in the lower strengthening effect by heat treatment.Thus,consistent with the characteristics of the forging process,a periodic variation of sample in strength is detected along the circumferential direction of the forged round bar.
基金supported by the National Natural Science Foundation of China(Nos.52371063 and 52072110)the Natural Science Foundation of Hebei Province(No.E2018202034)+1 种基金the Central Funds Guiding the Local Science and Technology Development of Hebei Province(No.236Z7610G)the Graduate Innovation Project of Hebei Province(No.CXZZBS2022035).
文摘High porosity and high brittleness are the main reasons that limit the long-term service life of the alumina-titanium oxide composite coating.Herein,a metastable nanostructured aluminatitanium oxide composite coating with high density and high properties was synthesized by plasma spraying of TiO_(2)-Al composite powder.The main phases of the metastable nanostructured alumina-titanium oxide wereγ-Al_(2)O_(3),TiO and AlTiO_(2).The coating,as prepared,contains various metastable microstructures,such as fine-grained,intra-/inter-granular,and"self-locking"microstructures.These metastable microstruc-tures are important for the improvement of hardness and toughness of the coating.Compared with other alumina-based composite coatings,the metastable nanostructured aluminatitanium oxide composite coating showed the most impressive overall performance.The reinforcing and toughening mechanism of the metastable alumina-titanium oxide composite coating included fine grain strengthening and self-toughening of the metastable microstructure.
基金supported by the China Postdoctoral Science Foundation(No.2022M720399).
文摘In order to investigate the damage tolerance of a metastable Ti-5Al-3V-3Mo-2Cr-2Zr-1Nb-1Fe(Ti5321)alloy with bimodal microstructure using void growth quantification and micromechanical modeling,in situ tensile testing was performed during X-ray microtomography experiments.Compared with investigations of surface voids by traditional two-dimensional(2D)methods involving post-mortem characterization,three-dimensional(3D)information on void evolution inside optically opaque samples obtained through X-ray microtomography is essential.The Rice and Tracey model and Huang model were applied to predict void growth and show good agreement with experimental data using calibration of the damage parameterα.The void growth kinetics of Ti5321 with bimodal microstructure was analyzed by comparing theαvalue with that of Ti64 for different microstructure morphologies.The damage mechanism of ductile fracture of Ti5321 with bimodal microstructure is discussed.It was found that the size of the voids apparently increases with the triaxiality of stress.Post-mortem scanning electron microscopy(SEM)was also used to demonstrate this damage mechanism of ductile fracture of Ti5321.
基金supported by the Key R&D Program of Zhejiang(No.KZ7240079).
文摘Metastable β-Ti alloys exhibiting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) generally have excellent ductility, but typically at the expense of relatively low yield strengths which has restricted their widespread use. Our work shows that interstitial oxygen can be employed to regulate β phase stability to significantly enhance both strength and ductility of TWIP/TRIP alloys. For a Ti-32Nb wt.% base alloy, inclusion of 0.3 wt.% O enhanced ductility by more than 140 %, reaching up to 54 % strain, and improved the tensile yield strength by over 95 % to 632 MPa. Compared to other common engineering alloys such as Ti-45Nb, elongation was increased by 29 %, and the yield strength increased by 182 MPa, respectively. Here, we elucidate on impacts of oxygen doping on TWIP/TRIP behaviors in the Ti-32Nb alloy. We reveal that oxygen regulates the critical stress for martensitic transformation, twinning, and dislocation slip. At lower oxygen doping concentrations (≤0.3 wt.% O), multi-stage martensitic transformation and martensitic twinning resulted in high ductility. In higher oxygen content alloys (≥0.5 wt.% O), deformation occurred initially via twinning, while strain induced martensite was subsequently induced in retained β phase regions. Oxygen concentrations control the deformation mechanisms, providing a flexible means to synergistically balance an alloy's strength and ductility. The use of oxygen to enhance stability of the β phase and regulate deformation behaviors is a promising new approach for creating high-performance TWIP/TRIP metastable β-Ti alloys with outstanding mechanical properties.
基金support from National Natural Science Foundation of China(No.52101122).Q.Zhao,R.Torrens,F.Yang and L.Bolzoni would like to gratefully acknowledge the support from New Zealand Ministry of Business,Innovation and Employment(No.UOWX1402)supported by Science and Technology Major Project of Shaanxi Province(No.2020-zdzx04-01-02)+1 种基金Key Research Plan of Shaanxi Province(No.2021KW-18)Young Talents Promotion Project of China Association for Science and Technology(No.YESS20200335).
文摘Thermomechanical processing(TMP)is especially crucial for metastableβtitanium alloys,which has received significant attention in the community for a long time.In this contribution,the processing-responding behaviour including microstructure evolution process,texture variation mechanism,and un-derlying deformation process of powder metallurgy Ti-5553 alloy in a wide processing parameter range was comprehensively investigated.Thermal physical simulation was performed on the alloy at temper-atures ranging from 800℃ to 1100℃,and strain rates between 0.001 s^(−1) and 10 s^(−1),to varied defor-mation degrees of 20%-80%height reduction.It was found that the processing parameters(i.e.temper-ature,strain rate,and deformation degree)are influential on the deformation process and resultant mi-crostructure.Varied microstructural evolution processes forβphase including flow localization,dynamic recovery,dynamic recrystallization,and grain coarsening are activated in different processing domains,while different evolution mechanisms forαphase including dynamic precipitation,phase separation,dy-namic coarsening,and mechanical shearing also play their roles under different processing conditions.In particular,four exceptional evolution mechanisms ofαprecipitation which have not been previously reported in titanium alloys were discovered and clearly demonstrated,more specifically,they are multi-interior twinning,internal compositing,layered coarsening and selective diffusion-actuated separation.After the establishment of comprehensive microstructural evolution mechanism maps,the guidance for precise processing and the knowledge reserve extension for deformation process of metastableβtita-nium alloys can be effectively achieved.
基金financially supported by the Major State Research Development Program of China(No.2016YFB0701303)the National Natural Science Foundation of China(No.51801156)the Natural Science Basic Research Plan in Shaanxi Province of China(No.2019JM-584)。
文摘In this work,the effect of microstructure features on the high-cycle fatigue behavior of Ti-7Mo-3Nb-3Cr-3Al(Ti-7333)alloy is investigated.Fatigue tests were carried out at room temperature in lab air atmosphere using a sinusoidal wave at a frequency of 120 Hz and a stress ratio of 0.1.Results show that the fatigue strength is closely related to the microstructure features,especially theα_(p) percentage.The Ti-7333 alloy with a lowerα_(p) percentage exhibits a higher scatter in fatigue data.The bimodal fatigue behavior and the duality of the S-N curve are reported in the Ti-7333 alloy with relatively lowerα_(p) percentage.Crack initiation region shows the compoundα_(p)/βfacets.Facetedα_(p) particles show crystallographic orientation and morphology dependence characteristics.Crack-initiation was accompanied by faceting process across elongatedα_(p) particles or multiple adjacentα_(p) particles.These particles generally oriented for basal slip result in near basal facets.Fatigue crack can also initiate at elongatedα_(p) particle well oriented for prismatic slip.Theβfacet is in close correspondence to{110}or{112}plane with high Schmid factor.Based on the fracture observation and FIB-CS analysis,three classes of fatigue-critical microstructural configurations are deduced.A phenomenological model for the formation ofα_(p) facet in the bimodal microstructure is proposed.This work provides an insight into the fatigue damage process of theβprecipitate strengthened metastableβtitanium alloys.
基金National Natural Science Foundation of China(52104379,U21A20117,52071219,52271249)。
文摘To study the relationship between the microstructure and tensile properties of the novel metastable β titanium alloy Ti-5.5Cr-5Al-4Mo-3Nb-2Zr,a heat treatment process of ABFCA(solid solution in α+βregion with subsequent furnace cooling followed by aging treatment finally)was designed,by which α phases of different sizes can be precipitated in the β matrix.The results show that the microstructure obtained by this heat treatment process is composed of primary α(α_(p))phase,submicro rod-like α(α_(r))phase and secondary α(α_(s))phase.The alloy with multi-scale α phase has an excellent balance between strength and ductility.The elongation is about 18.3% at the ultimate tensile strength of 1125.4 MPa.The relationship between the strength of the alloy and the α phase was established.The strength of the alloy is proportional to the power of‒1/2 of the average spacing and width of α phase.The α_(s) phase with a smaller size and phase spacing can greatly improve the strength of the alloy by hindering dislocation slip.The transmission electron microscope analysis shows that there is a large amount of dislocation accumulation at the α/β interfaces,and many deformation twins are found in the α_(p) phase after tensile deformation.When the dislocation slip is hindered,twins occur at the stress concentration location,and twins can initiate some dislocations that are difficult to slip.Meanwhile,the plastic strain is distributed uniformly among the α_(p),α_(r),α_(s) phases and β matrix,thereby enhancing the ductility of the alloy.
基金Project(2007CB613802)supported by the National Basic Research Program of ChinaProject(KP200912)supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU),China
文摘A new metastable β type titanium alloy called TB-13 with the combination of excellent strength and ductility was developed successfully.In order to develop a perspective on this new alloy,the influence of several commonly used heat treatments on the microstructure and properties was studied.In solution-treated and quenched samples,a low-temperature aging at 480°C results in the precipitation of finerαphase.The precipitation of coarserαphase plate at higher aging temperature(560°C)leads to the increase of tensile ductility but reduction of strength.During low-temperature aging at 300°C,quite homogeneous distribution of fine isothermalωphase particles was found.The isothermalωphase provides nucleation sites forαphase during two-step aging process and makesαphase extremely fine and disperse uniformly in β matrix.Thus,TB-13 alloy is strengthened and its mechanical properties are improved.
文摘The constitutive model was developed to describe the relationship among flow stress,strain,strain rate,and deformation temperature completely,based on the characteristics of flow stress curves for a new kind of metastable β Ti2448 titanium alloy from isothermal hot compression tests,in a wide range of temperatures（1023-1123 K） and strain rates（63-0.001 s-1）.During this process,the adopted hyperbolic sine function based on the unified viscoplasticity theory was used to model the flow behavior of alloy undergoing flow softening caused by dynamic recovery（DRV） at high strain rates（≥1 s-1）.The standard Avrami equation was adopted to represent the softening mechanism attributed to dynamic recrystallization（DRX） at low strain rates（1 s-1）.Additionally,the material constants were determined by optimization strategy,which is a new method to solve the nonlinear constitutive equation.The stress—strain curves predicted by the developed constitutive model agree well with the experimental results,which con-rms that the developed constitutive model can give an accurate estimate of the-ow stress of Ti2448 titanium alloy and provide an effective method to model the flow behavior of metastable β titanium alloys during hot deformation.
基金supported by National Natural Science Foundation of China(51801156)Major State Research Development Program of China(2016YFB0701305)+1 种基金Natural Science Basic Research Plan in Shaanxi Province of China(2018JQ5035)the Fundamental Research Funds for the Central Universities(G2017KY0310).
文摘The compressive yielding phenomenon of titanium alloys is not as focused and sufficiently ascertain as the tensile yielding phenomenon.In the present work,the peculiar compressive yielding behavior and the different dynamic responses of three different initial microstructures(singleβ,clavateβand lamellarβ)were investigated in an attractive metastableβtitanium alloy Ti-5553 using electron microscopes/crystallographic calculation/crystal plastic finite element simulation.Results reveal that the distinct compressive yielding behavior,steep peaks of sudden drop in the initial stage(very small true strain 0.03)of stress loading have appeared in the compression stress-strain curves except for the lamellarβinitial microstructure.Dislocation slip is the essential mechanism of the initial yielding behavior.Interlaced multiple-slip bands formed in the singleβinitial microstructure during the warm deformation process.A small quantity of single slip bands was observed in the deformed clavateβinitial microstructure.The abundant varied nano/ultrafineβsprecipitates were nucleated dynamically and dispersedly in all the three deformed initial microstructures.The multiple-slip bands formation and substantial nanoscaleβsresult in the highest peak of flow stress for singleβinitial microstructure.The compressive slip bands are formed early in the elastic–plastic deformation stage.As the increasing strain,the sample showed a significant compressive bulge,or eventually forming a strong adiabatic shear band or crack.These results are expected to provide a reference for the study of deformation behavior and mechanical properties of metastableβtitanium alloys.
基金supported financially by the National Natural Science Foundation of China (Nos.U19A2085 and 51627805)the Key-Area Research and Development Program of Guangdong Province (No.2020B090923001)+2 种基金the Key Basic and Applied Research Program of Guangdong Province (No.2019B030302010)the Optical Valley Science Research Project,WEHDZ (No.2019001)financial support from the China Postdoctoral Science Foundation (Nos.2019TQ0099 and 2019M662908)。
文摘It is well accepted that grain-boundary phases in metallic alloys greatly deteriorate the mechanical properties.In our work,we report on a novel strategy to prepare high strength-ductility β-type(Ti69.71 Nb23.72Zr4.83Ta1.74)97Si3(at.%)(TNZTS) alloys by tailoring grain-boundary metastable Si-containing phase.Specifically,the thin shell-shaped metastable S1 phase surrounding the columnar β-Ti grain was intercepted successfully via nonequilibrium rapid solidification achieved by selective laser melting(SLM).Subsequently,the thin shell-shaped metastable(Ti,Nb,Zr)5 Si3(called S1) phase was transformed into globular(Ti,Nb,Zr)2 Si(called S2) phase by the solution heat treatment.Interestingly,the globular S2 phases reinforced TNZTS alloy exhibits ultrahigh yield strength of 978 MPa,ultimate strength of 1010 MPa and large elongation of 10.4 %,overcoming the strength-ductility trade-off of TNZTS alloys by various methods.Especially,the reported yield strength herein is 55 % higher than that of conventionally forged TNZT alloys.Dynamic analysis indicates the globularization process of the metastable S1 phase is controlled by the model of termination migration.The quantitative analysis on strengthening mechanism demonstrates that the increase in yield strength of the heat-treated alloys is mainly ascribed to the strengthening of the precipitated silicide and the dislocations induced by high cooling rate.The obtained results provide some basis guidelines for designing and fabricating β-titanium alloys with excellent mechanical properties,and pave the way for biomedical application of TNZTS alloy by SLM.
文摘This study investigates the development of novel high-entropy alloys(HEAs)with enhanced mechanical properties through an innovative fabrication method of direct energy deposition(DED).The focus is on the creation of metastable core-shell precipitation-strengthened HEAs that exhibit a unique multi-stage terrace-like slip wave toughening mechanism,a novel approach to improving both strength and ductility simultaneously.Mechanical testing reveals that the developed HEAs exhibit superior mechanical proper-ties,including high yield strength,ultimate tensile strength,and exceptional ductility.The improvement in these properties is attributed to the multi-stage terrace-like slip wave toughening mechanism activated by the unique microstructural features.This toughening mechanism involves the sequential activation of slip systems,facilitated by the stress concentration around the core-shell precipitates and the subsequent propagation of slip waves across the material.The terrace-like pattern of these slip waves enhances the material's ability to deform plastically,providing a significant toughening effect while maintaining high strength levels.Furthermore,the study delves into the fundamental interactions between the microstruc-tural elements and the deformation mechanisms.It elucidates how the core-shell precipitates and the matrix cooperate to distribute stress uniformly,delay the onset of necking,and prevent premature failure.This synergistic interaction between the microstructural features and the slip wave toughening mecha-nism is central to the remarkable balance of strength and ductility achieved in the HEAs.The introduction of a multi-stage terrace-like slip wave toughening mechanism offers a new pathway to designing HEAs with an exceptional amalgamation of strength and ductility.
基金supported financially by the National Natural Science Foundation of China (Nos. 51671158 and 51621063)the National Program on Key Basic Research Project (No. 2014CB644003)the Programme of Introducing Talents of Discipline to Universities (No. PB2018008)。
文摘β titanium alloys with bi-modal structure which exhibit improved strength-ductility combination and fatigue property are widely used in aviation and aerospace industry.However,owing to the small size of primary α(αp) and nano-scaled multi variant distribution of secondary α platelets(αs),investigating the deformation behavior is really a challenging work.In this work,by applying transmission electron microscopy(TEM),the slip behavior in αp and transformed β matrix with different tensile strain was studied.After α/β solution treatment,the initial dislocation slips on {110} plane with <1 1 1> direction in β matrix.During furtherdeformation,(110),(101) and(1 1 2) multi slip is generated which shows a long straight cro s sing configuration.Dislocation cell is exhibited in β matrix at tensile strain above 20 %.Diffe rent from the solid solution treated sample,high density wavy dislocations are generated in transformedβ matrix.High fraction fine as hinders dislocation motion in β matrix effectively which in turn dominates the strength of the alloy.In primary α phase(αp),a core-shell structure is formed during deformation.Both pyramidal a+c slip and prismatic/basal a slip are generated in the shell layer.In core region,plastic deformation is governed by prismatic/basal a slip.Formation of the core-shell structure is the physical origin of the improved ductility.On one hand,the work hardening layer(shell) improves the strength of αp,which could deform compatibly with the hard transformed β matrix.Meanwhile,the center area(core) deforms homogeneously which will sustain plastic strain effectively and increase the ductility.This paper studies the slip behavior and reveals the origin of the improved strength-ductility combination in Bi-modal structure on a microscopic way,which will give theoretical advises for developing the next generation high strength β titanium alloys.
基金National Science and Technology Project of China(JPPT-135-GH-2-017)Fellowship of China Postdoctoral Science Foundation(2022M720399)。
文摘The effect of die forging on the microstructure evolution and deformation behavior of metastable β-titanium alloy Ti55511 was investigated by electron backscatter diffraction.Before die forging,the alloy Ti55511 was subjected to multi-pass forging to optimize the microstructural heterogeneity(texture)which can cause mechanical behavior anisotropy of titanium alloys.Results show that after die forging,Ti55511 components exhibit different microstructures and textures in different local areas.No<100>fiber texture is found in all areas with different degrees of deformation.Dynamic recrystallization occurs in the area where large strain occurs during the early stage of die forging.Basket-weave microstructure forms in most local areas.
基金the financial assistance provided by Ministry of High Education and Scientific Research, the Government of Iraq
文摘The influence of thermo-mechanical processing (TMP) on the microstructure and the electrochemical behavior of new metastableβ alloy Ti?20.6Nb?13.6Zr?0.5V (TNZV) was investigated. The TMP included hot working in belowβ transus, solution heat treatments at the same temperature and different cooling rates in addition to aging. Depending upon the TMP conditions, a wide range of microstructures with varying spatial distributions and morphologies of equiaxed/elongatedα andβ phases were attained, allowing for a wide range of electrochemical properties to be achieved. The corrosion behavior of the studied alloy was evaluated in a Ringer’s solution at 37 °C via open circuit potential?time and potentiodynamic polarization measurements.
文摘Influence of severe cold deformation of titanium alloy Ti-1.5%A1-6.8%Mo-4.5%Fe in metastable β condition on the evolution of phase composition, microstructure, and tensile properties during continuous rapid heating was studied. As-deformed alloy was characterized by quasi-amorphous single-phase β condition with an abnormal temperature dependence of electric resistance that was normalized after 48 h exposure at room temperature as a result of isothermal ω phase precipitation. Subsequent rapid heating with a rate of 5 ℃/s caused recovery and recrystallization. Tensile properties of the alloy after different treatments were determined and discussed.
