The effects of different aging processes on the microstructure and mechanical properties of a novel Al-Cu-Li alloy have been investigated by X-ray diffraction, scanning electron microscopy and transmission electron mi...The effects of different aging processes on the microstructure and mechanical properties of a novel Al-Cu-Li alloy have been investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. It is found that the tensile properties of a novel Al-Cu-Li alloy are sensitive to aging processes, which correspond to different microstructures. σ（Al_5Cu_6Mg_2） and T_1（Al_2CuLi） phases are the major precipitates for the alloy in T6 aging condition（165 ℃/60 h）. After duplex aging condition（150 ℃/24 h ＋ 180 ℃/12 h）, σ, θ＇（Al_2Cu） and T_1 phases are detected. Only the T_1 phases can be found in the T8 state alloy（6% pre-strain＋135 ℃/60 h）. The failure modes of alloy in T6 and duplex aging conditions are dimple-intergranular fracture, while typical quasi-cleavage fracture in T8 condition.展开更多
A successful mechanical property data-driven prediction model is the core of the optimal design of hot rolling process for hot-rolled strips. However, the original industrial data, usually unbalanced, are inevitably m...A successful mechanical property data-driven prediction model is the core of the optimal design of hot rolling process for hot-rolled strips. However, the original industrial data, usually unbalanced, are inevitably mixed with fluctuant and abnormal values. Models established on the basis of the data without data processing can cause misleading results, which cannot be used for the optimal design of hot rolling process. Thus, a method of industrial data processing of C-Mn steel was proposed based on the data analysis. The Bayesian neural network was employed to establish the reliable mechanical property prediction models for the optimal design of hot rolling process. By using the multi-objective optimization algorithm and considering the individual requirements of costumers and the constraints of the equipment, the optimal design of hot rolling process was successfully applied to the rolling process design for Q345B steel with 0.017% Nb and 0.046% Ti content removed. The optimal process design results were in good agreement with the industrial trials results, which verify the effectiveness of the optimal design of hot rolling process.展开更多
Semisolid-rolling method was successfully developed to prepare the Ni-coated woven carbon fibers reinforced Al-matrix composite. Due to the appropriate matrix flowability and rolling pressure, the Al-matrix could infi...Semisolid-rolling method was successfully developed to prepare the Ni-coated woven carbon fibers reinforced Al-matrix composite. Due to the appropriate matrix flowability and rolling pressure, the Al-matrix could infiltrate into the woven fibers sufficiently and attach to the reinforcements closely forming a smooth interface. The rolling speed of 4 rad/min offered a subtle equilibrium between the heat transfer and the material deformation. The covering matrix should be controlled at semisolid state to provide a better infiltration behavior and a protective effect on the carbon fibers. With the addition of fibers, an improvement for more than 25% was obtained in the bending strength of the materials. Furthermore, the woven carbon fibers could strengthen the composite in multiple directions, rather than only along the fiber longitudinal directions. The annealing process promoted the Ni coating to react with and to diffuse into the matrix, resulted in an obvious increase of the bending strength.展开更多
The stretch formability of a low carbon steel processed by friction stir processing （FSP） was studied under biaxial loading condition applied by a miniaturized Erichsen test. One-pass FSP decreased the ferritic grai...The stretch formability of a low carbon steel processed by friction stir processing （FSP） was studied under biaxial loading condition applied by a miniaturized Erichsen test. One-pass FSP decreased the ferritic grain size in the processed zone from 25 μm to about 3 μm, which also caused a remarkable increase in strength values without considerable decrease in formability under uniaxial loading. A coarse-grained （CG） sample before FSP reflected a moderate formability with an Erichsen index （EI） of 2.73 mm. FSP slightly decreased the stretch formability of the sample to 2.66 ram. However, FSP increased the required punch load （FEI） due to the increased strength by grain refinement. FSP reduced considerably the roughness of the free surface of the biaxial stretched samples with reduced orange peel effect. The average roughness value （Ra） decreased from 2.90 in the CG sample down to about 0.65 μm in fine-grained （FG） sample after FSP. It can be concluded that the FG microstructure in low carbon steels sheets or plates used generally in shipbuilding provides a good balance between strength and formability.展开更多
To evaluate the property of the organic coatings in oil and gas plants, the aging process was studied in high temperature and high CO_2 partial pressure environment. Correlations were developed between the macroscopic...To evaluate the property of the organic coatings in oil and gas plants, the aging process was studied in high temperature and high CO_2 partial pressure environment. Correlations were developed between the macroscopic properties and microstructure of the organic coatings. The surface appearance, mechanical properties, and permeability of the organic coatings were measured. Furthermore, the crystal structure of the organic coatings was investigated through synchrotron radiation grazing incidence X-ray diffraction（GIXRD） on the BL14B1 beam line in Shanghai Synchrotron Radiation Facility. Combined with the Fourier transform infrared spectroscopy, the molecular structure of the organic coatings was investigated. The experimental results indicate that the thickness variation and weight loss of the organic coatings increase with the immersion time, and the penetration resistance of the coating obviously decreases as the temperature rises. Moreover, the degradation of the organic coatings with immersion time in high temperature and high CO_2 partial pressure environment is caused by the amorphization of the organic coatings as the groups and bonds of the organic coatings were not damaged.展开更多
基金the National High Technology Research and Development Program of China (Grant No.2013AA032401)
文摘The effects of different aging processes on the microstructure and mechanical properties of a novel Al-Cu-Li alloy have been investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. It is found that the tensile properties of a novel Al-Cu-Li alloy are sensitive to aging processes, which correspond to different microstructures. σ（Al_5Cu_6Mg_2） and T_1（Al_2CuLi） phases are the major precipitates for the alloy in T6 aging condition（165 ℃/60 h）. After duplex aging condition（150 ℃/24 h ＋ 180 ℃/12 h）, σ, θ＇（Al_2Cu） and T_1 phases are detected. Only the T_1 phases can be found in the T8 state alloy（6% pre-strain＋135 ℃/60 h）. The failure modes of alloy in T6 and duplex aging conditions are dimple-intergranular fracture, while typical quasi-cleavage fracture in T8 condition.
文摘A successful mechanical property data-driven prediction model is the core of the optimal design of hot rolling process for hot-rolled strips. However, the original industrial data, usually unbalanced, are inevitably mixed with fluctuant and abnormal values. Models established on the basis of the data without data processing can cause misleading results, which cannot be used for the optimal design of hot rolling process. Thus, a method of industrial data processing of C-Mn steel was proposed based on the data analysis. The Bayesian neural network was employed to establish the reliable mechanical property prediction models for the optimal design of hot rolling process. By using the multi-objective optimization algorithm and considering the individual requirements of costumers and the constraints of the equipment, the optimal design of hot rolling process was successfully applied to the rolling process design for Q345B steel with 0.017% Nb and 0.046% Ti content removed. The optimal process design results were in good agreement with the industrial trials results, which verify the effectiveness of the optimal design of hot rolling process.
基金supported by the National Natural Science Foundation of China (Nos. 51271042 and 51501027)the Fundamental Research Funds for the Central Universities, the Key Laboratory of Basic Research Projects of Liaoning Province Department of Education (No. LZ2014007)+1 种基金the Natural Science Foundation of Liaoning Province (No. 2014028013)China Postdoctoral Science Foundation (No. 2015M570246)
文摘Semisolid-rolling method was successfully developed to prepare the Ni-coated woven carbon fibers reinforced Al-matrix composite. Due to the appropriate matrix flowability and rolling pressure, the Al-matrix could infiltrate into the woven fibers sufficiently and attach to the reinforcements closely forming a smooth interface. The rolling speed of 4 rad/min offered a subtle equilibrium between the heat transfer and the material deformation. The covering matrix should be controlled at semisolid state to provide a better infiltration behavior and a protective effect on the carbon fibers. With the addition of fibers, an improvement for more than 25% was obtained in the bending strength of the materials. Furthermore, the woven carbon fibers could strengthen the composite in multiple directions, rather than only along the fiber longitudinal directions. The annealing process promoted the Ni coating to react with and to diffuse into the matrix, resulted in an obvious increase of the bending strength.
基金supported by “The World Academy of Sciences,Italy(TWAS)” under the Visiting Researchers Program of TWASUNESCO Associateship Scheme(Ref.3240260896)
文摘The stretch formability of a low carbon steel processed by friction stir processing （FSP） was studied under biaxial loading condition applied by a miniaturized Erichsen test. One-pass FSP decreased the ferritic grain size in the processed zone from 25 μm to about 3 μm, which also caused a remarkable increase in strength values without considerable decrease in formability under uniaxial loading. A coarse-grained （CG） sample before FSP reflected a moderate formability with an Erichsen index （EI） of 2.73 mm. FSP slightly decreased the stretch formability of the sample to 2.66 ram. However, FSP increased the required punch load （FEI） due to the increased strength by grain refinement. FSP reduced considerably the roughness of the free surface of the biaxial stretched samples with reduced orange peel effect. The average roughness value （Ra） decreased from 2.90 in the CG sample down to about 0.65 μm in fine-grained （FG） sample after FSP. It can be concluded that the FG microstructure in low carbon steels sheets or plates used generally in shipbuilding provides a good balance between strength and formability.
基金Funded by the National Science and Technology Major Project(2011ZX05022-013)
文摘To evaluate the property of the organic coatings in oil and gas plants, the aging process was studied in high temperature and high CO_2 partial pressure environment. Correlations were developed between the macroscopic properties and microstructure of the organic coatings. The surface appearance, mechanical properties, and permeability of the organic coatings were measured. Furthermore, the crystal structure of the organic coatings was investigated through synchrotron radiation grazing incidence X-ray diffraction（GIXRD） on the BL14B1 beam line in Shanghai Synchrotron Radiation Facility. Combined with the Fourier transform infrared spectroscopy, the molecular structure of the organic coatings was investigated. The experimental results indicate that the thickness variation and weight loss of the organic coatings increase with the immersion time, and the penetration resistance of the coating obviously decreases as the temperature rises. Moreover, the degradation of the organic coatings with immersion time in high temperature and high CO_2 partial pressure environment is caused by the amorphization of the organic coatings as the groups and bonds of the organic coatings were not damaged.
