Paraphenylenediamine(PPDA)-grafted maleic anhydride(MAH)-modified graphene oxide(PGO)was synthesized through a dual modification process.Initially,MAH was employed to modify graphene oxide(GO)to enhance its reactive s...Paraphenylenediamine(PPDA)-grafted maleic anhydride(MAH)-modified graphene oxide(PGO)was synthesized through a dual modification process.Initially,MAH was employed to modify graphene oxide(GO)to enhance its reactive sites.Subsequently,PPDA was utilized for further modification of MAH-modified GO(MGO).Through a comprehensive analysis,the successful grafting of MAH and PPDA onto GO was confirmed.It was concurrently established that the optimal ratio of PPDA to MGO is 1:1.This approach yielded PGO characterized by outstanding dispersibility and barrier properties in epoxy resin(EP)coaings for Q235 steel.The corrosion resistance of EP coatings containing varying amounts of PGO was assessed using electrochemical workstation and salt spray testing.After immersing in a 3.5 wt.%NaCl solution for 300 h,the composite coating containing 0.1 wt.%PGO exhibited superior performance in terms of low-frequency impedance modulus,measuring at 1.1×10^(8)Ωcm^(2).The lowest corrosion current density was 2.32×10^(–10)A cm^(−2),and the self-corrosion voltage was−0.301 V.Additionally,polarization testing indicated that this coating also displayed the lowest corrosion rate,specifically 1.383×10^(–7)mm/a.展开更多
Ni/Al2O3 catalysts were derived from spinel NiAl2O4 with different Ni content ((2.5, 5 and 7.5) wt%). The catalysts were obtained by H-2 reduction and were investigated for the low-temperature hydrogenation of maleic ...Ni/Al2O3 catalysts were derived from spinel NiAl2O4 with different Ni content ((2.5, 5 and 7.5) wt%). The catalysts were obtained by H-2 reduction and were investigated for the low-temperature hydrogenation of maleic anhydride (MA) to produce succinic anhydride (SA). The characterization results showed that Ni-0 active sites were mainly derived during the H2 reduction from spinel NiAl2O4 Among the catalysts studied, employing the optimum preparation and reaction conditions with Ni(5%)/Al2O3 yielded the highest catalytic performance. A near-100% conversion of MA and similar to 90% selectivity to SA were achieved at 120 degrees C and 0.5 MPa of H-2 with a weighted hourly space velocity (MA) of 2 h(-1). (C) 2017, Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.展开更多
Starch,as a typical polysaccharide with natural spherical morphology,is not only a preferred precursor for preparing carbon materials but also a model polymer for investigating thermochemical evolution mechanisms.Howe...Starch,as a typical polysaccharide with natural spherical morphology,is not only a preferred precursor for preparing carbon materials but also a model polymer for investigating thermochemical evolution mechanisms.However,starch usually suffers from severe foaming and low carbon yield during direct pyrolysis.Herein,we report a simple and eco-friendly dry strategy,by maleic anhydride initiating the esterification of starch,to design carbon microspheres against the starch foaming.Moreover,the infuence of ester grafting on the pyrolytic behavior of starch is also focused.The formation of ester groups in precursor guarantees the structural stability of starch-based intermediate because it can promote the accumulation of unsaturated species and accelerate the water elimination during pyrolysis.Meanwhile,the esterification and dehydration reactions greatly deplete the primary hydroxyl groups in the starch molecules and thus the rapid levoglucosan release is inhibited,which well keeps the spherical morphology of starch and ensures the high carbon yield.In further exploration as anode materials for Lithium-ion batteries,the obtained carbon microspheres exhibit good cyclability and rate performance with a reversible capacity of 444 m Ah g^(-1)at 50 m A g^(-1).This work provides theoretical fundamentals for the controllable thermal transformation of biomass towards wide applications.展开更多
The pseudo-boehmite derived alumina supported metal（Cu,Co and Ni） catalysts prepared by the impregnation method were investigated in hydrogenation of maleic anhydride（MA） to succinic anhydride（SA） and γ-butyrol...The pseudo-boehmite derived alumina supported metal（Cu,Co and Ni） catalysts prepared by the impregnation method were investigated in hydrogenation of maleic anhydride（MA） to succinic anhydride（SA） and γ-butyrolactone.The catalysts were characterized by ICP-AES,N2 adsorptiondesorption,XRD,H2-TPR,CO-TPD,dissociative N2O adsorption and TEM and the results showed that the alumina possessed mesoporous feature and the metal species were well dispersed on the support.Compared to Cu/Al2O3 and Co/Al2O3,Ni/Al2O3 exhibited higher catalytic activity in the MA hydrogenation with 92%selectivity to SA and nearly 100%conversion of MA at 140 °C under 0.5 MPa of H2 with a weighted hourly space velocity of 2 h 1（MA）.The stability of Ni/Al2O3 catalyst was also investigated.展开更多
A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA’s hydrophilicity and cell affinity and to provide reactive...A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA’s hydrophilicity and cell affinity and to provide reactive groups for further chemical modification. FTIR, 13C NMR and DSC were used to characterize the maleic anhydride-modified PDLLA.展开更多
Solid-liquid equilibria (SLE) of three binary systems and seventernary systems containing maleic an- hydride (MA) are measured byvisual method. The experimental data are compared with the calculatedones with modified ...Solid-liquid equilibria (SLE) of three binary systems and seventernary systems containing maleic an- hydride (MA) are measured byvisual method. The experimental data are compared with the calculatedones with modified universal quasichemical functional group activitycoefficient (UNIFAC) method in which the interaction parametersbetween groups come from two sources, dortmund data bank (DDB), ifthere's any, and correlations based on our former presentedexperimental SLE data of twenty binary systems.展开更多
Natural rubber grafted maleic anhydride （NR-g-MAH） was synthesized by mixing maleic anhydride （MAH） and natural rubber （NR） in solid state in a torque rheometer using dicurnyl peroxide （DCP） as initiator. Then...Natural rubber grafted maleic anhydride （NR-g-MAH） was synthesized by mixing maleic anhydride （MAH） and natural rubber （NR） in solid state in a torque rheometer using dicurnyl peroxide （DCP） as initiator. Then the self-prepared NR-g-MAH was used as a compatibilizer in the natural rubber/short nylon fiber composites. Both the fimctionalization of NR with MAH and the reaction between the modified rubber and the nylon fiber were confirmed by Fourier transform infrared spectroscopy （FTIR）. Composites with different nylon short fiber loadings （0, 5, 10, 15 and 20 phr） were compounded on a two-roll mill, and the effects of the NR-g-MAH on the tensile and thermal properties, fiber-rubber interaction, as well as the morphology of the natural rubber/short nylon fiber composites were investigated. At equal fiber loading, the NR-g-MAH compatibilized NR/short nylon fiber composites showed improved tensile properties, especially the tensile modulus at 100% strain which was about 1.5 times that of the corresponding un-compatibilized ones. The equilibrium swelling tests proved that the incorporation of NR-g-MAH increased the interaction between the nylon fibers and the NR matrix. The crosslink density measured with NMR techniques showed that the NR-g-MAH compatiblized composites had lower total crosslink density. The glass transition temperatures of the compatibilized composites were about 1 K higher than that of the corresponding un-compabilized ones. Morphology analysis of the NR/short nylon fiber composites confirmed NR-g-MAH improved interfacial bonding between the NR matrix and the nylon fibers. All these results signified that the NR-g-MAH could act as a good compatilizer of NR/short nylon fiber composites and had a potential for wide use considering its easy to be prepared and compounded with the composites.展开更多
In this work,the hydrogenation of maleic anhydride to succinic anhydride in the presence of 5 m%Ni/clay catalysts was investigated.These catalysts were characterized by X-ray diffraction(XRD),H2 temperature programmed...In this work,the hydrogenation of maleic anhydride to succinic anhydride in the presence of 5 m%Ni/clay catalysts was investigated.These catalysts were characterized by X-ray diffraction(XRD),H2 temperature programmed reduction(TPR)and thermogravimetric analysis(TGA)techniques.The XRD and TPR studies showed that Ni was present as Ni2+on the support,which indicated that there were no elemental nickel(Ni^0)and Ni203 species in the unreduced samples.Increasing of calcination temperature to 650℃leads to destruction of the support structure observed in TGA,while the catalyst sample calcined at 550℃exhibits better performances than other samples.The ideal conversion of maleic anhydride(97.14%)and selectivity of succinic anhydride(99.55%)were realized at a reaction temperature of 180℃and a weight hourly space velocity of 4 h^-1 under a reaction pressure of 1 MPa.展开更多
The colloidal carbon microspheres(CMS)were prepared by the hydrothermal method.The nickel catalysts supported on carbon microspheres(Ni/CMS)were further prepared and were characterized by the Fourier transform infrare...The colloidal carbon microspheres(CMS)were prepared by the hydrothermal method.The nickel catalysts supported on carbon microspheres(Ni/CMS)were further prepared and were characterized by the Fourier transform infrared spectroscopy(FTIR),the X-ray diffraction(XRD),the scanning electron microscopy(SEM),the transmission electron microscopy(TEM),and the N_(2)adsorption technique.The selective hydrogenation of maleic anhydride(MA)to succinic anhydride(SA)over the Ni/CMS catalysts was investigated.The results indicated that the Ni/CMS catalyst,which was prepared with glucose as carbon source and calcined at 500℃,exhibited the best performance.The hydrogen pressure,reaction temperature,and reaction time could significantly affect the conversion of maleic anhydride during the hydrogenation reaction.A 98.4%conversion of MA and an 100%selectivity to SA were achieved over the Ni/CMS catalyst in acetic anhydride solvent under mild conditions covering a temperature of 90℃,a H2 pressure of 1.0 MPa,and a reaction time of 3 h.展开更多
Pd catalysts suffered from poor selectivity and stability for liquid-phase hydrogenation of maleic anhydride（MA） to gamma-butyrolactone（GBL）.Thus,Pd/C catalysts modified with different Sn loadings were synthesized...Pd catalysts suffered from poor selectivity and stability for liquid-phase hydrogenation of maleic anhydride（MA） to gamma-butyrolactone（GBL）.Thus,Pd/C catalysts modified with different Sn loadings were synthesized,and characterized by XRD,XPS,TEM and elemental mapping.The types of alloy phase and the amounts of the surface Pd-SnOx sites altered along with Sn/Pd mass ratios from 0-1.0synthesized in the process of preparation.The maximum reaction rate was 0.57 mol-GBL/（mol-Pd min）and selectivity was 95.94%when the Sn/Pd mass ratio was 0.6.It might be attributed to the formation of Pd2Sn alloy and less amounts of Pd-SnOx sites.展开更多
Magnesium hydroxide(MH) whiskers were modified via in situ polymerization of n-butyl acrylate and maleic anhydride. Sodium dodecyl sulfonate was used as emulsifier. The modifying effect was evaluated by using contact ...Magnesium hydroxide(MH) whiskers were modified via in situ polymerization of n-butyl acrylate and maleic anhydride. Sodium dodecyl sulfonate was used as emulsifier. The modifying effect was evaluated by using contact angle and activation index. The thermal stability,functional groups, structure, morphology, phase composition and surface element valence of MH whiskers were characterized by thermogravimetry-differential scanning calorimetry(TG-DSC), Fourier transform infrared spectroscopy(FTIR), X-ray diffraction(XRD), scanning electron microscopy(SEM) and X-ray photoelectron spectroscopy(XPS). Results reveal that the contact angle and activation index of modified MH whiskers are 105°and 76.5%, the thermal stability shows little change, and the decomposition temperature ranges between 38 and419 ℃. The copolymer of n-butyl acrylate and maleic anhydride absorbed on the surface of MH whiskers leads to the increased diameter and makes the surface of whiskers be rougher. Furthermore, the absorption of element C on the surface of MH whiskers increases, and the diffraction intensity of C 1 s spectra increases; thus, the compatibility of whiskers in the organic phase can be improved significantly. Lastly, the surface molecular model of MH whiskers modified via in situ copolymerization of n-butyl acrylate and maleic anhydride is established.展开更多
The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by cons...The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by constant concentration of chain radicals during the copolymerization, linear evolution of molecular weights with conversion and narrow molecular weight distribution (M-w/M-n = 1.23-1.35). The compositional analysis and the sequence structural information of the copolymers obtained from DEPT (Distortionless Enhancement by Polarization Transfer) experiments demonstrate that the copolymers obtained also possess strictly alternating structure.展开更多
A preliminary study of using maleic anhydride copolymer for protein binding has been carried out. The polymeric films were prepared by compression of the purified resin and annealing the film to induce efficient back ...A preliminary study of using maleic anhydride copolymer for protein binding has been carried out. The polymeric films were prepared by compression of the purified resin and annealing the film to induce efficient back formation of the anhydride groups. The properties of the film surface were analyzed by attenuated total reflection Fourier transforms infrared spectroscopy and water contact angle measurements. The protein content was determined by Bradford assay. To obtain optimum conditions, immersion time for protein binding was examined. Results revealed that proteins can be successfully immobilized onto the film surface via covalent linkage. The efficiency of the covalent binding of the extractable protein to maleic anhydride-polyethylene film was estimated at 69.87 ug/cm2, although the film had low anhydride content （3%） on the surface.展开更多
Plasma polymerized maleic anhydride （MA） was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge （DBD）. The film properties were characterized by ...Plasma polymerized maleic anhydride （MA） was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge （DBD）. The film properties were characterized by water contact angle （WCA）, Fourier transfer infrared （FTIR）, X-ray photoelectron spectroscopy （XPS）, atomic force microscope （AFM） analysis, and a thickness profilometer. The influence of the processing parameters on the film properties such as tile power frequency and polymerization zone was investigated. The results show that anhydride group incorporated into the growing films is favorable at the frequency of 80 kHz and working pressure of 50 Pa. The poly （maleic anhydride） film is uniform and compact at an average deposition rate of 8 nm/min.展开更多
The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of...The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of maleic anhydride-tetrahydrofuran charge transfer complex in the chain initiation process. ESR study provides collateral evidence for the formation of maleic anhydride radical and tetrahydrofuran radical.展开更多
Aim:To evaluate the safety of the long term vas occlusion with styrene maleic anhydride (SMA) and its non-invasive reversal at the level of accessory reproductive glands (ARGs) in langurs.Methods:The morphology of sem...Aim:To evaluate the safety of the long term vas occlusion with styrene maleic anhydride (SMA) and its non-invasive reversal at the level of accessory reproductive glands (ARGs) in langurs.Methods:The morphology of seminal vesicle and ventral prostate was evaluated by light as well as transmission electron microscopy.Serum clinical chemistry and urine albumin were evaluated in an autoanalyzer using reagent kits.Fructose,acid phosphatase and zinc in the seminal plasma were evaluated spectrophotometrically according to the WHO manual.Serum testosterone, prostate specific antigen and sperm antibodies were evaluated by enzyme-linked immunosorbent assays (ELISA) using reagent kits and hematology was estimated according to standard procedures.Results:The morphological features and secretory activity of the seminal vesicle and prostate were normal as evidenced by the presence of well- developed mitochondria,rough endoplasmic reticulum,Golgi bodies,secretory granules and normal nuclear charac- teristics throughout the course of investigation.Serum testosterone and prostate specific antigen remained unaltered and serum antisperm antibodies level presented negative titres.Urine albumin was nil.Total red blood corpuscles (RBC),white blood corpuscles (WBC),hemoglobin (Hb) and red cell indices,serum protein,glucose,cholesterol, creatinine,creatine kinase (CK),serum glutamate oxalate transaminase (SGOT),serum glutamate pyruvate transami- nase (SGPT),lactate dehydrogenase (LDH),bilirubin,urea,triglycerides and high-density lipoprotein (HDL) did not show appreciable changes following vas occlusion and after its non-invasive reversal.Although fructose,acid phos- phatase (ACP) and zinc in the seminal plasma showed a significant reduction following vas occlusion,it could not be related to the morphology of seminal vesicle and prostate.Conclusion:SMA vas occlusion and its non-invasive reversal do not damage the accessory reproductive organs.展开更多
Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of ben...Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP in- reactor blend granules, and solid phase graft polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.展开更多
Esterified starch/polylactic acid（ES/PLA） blending composite was prepared by melting extrusion with maleic anhydride esterified starch and PLA as the raw materials. The composite was accelerated aging by using UV ag...Esterified starch/polylactic acid（ES/PLA） blending composite was prepared by melting extrusion with maleic anhydride esterified starch and PLA as the raw materials. The composite was accelerated aging by using UV aging box, and its properties were characterized by Fourier transform infrared spectroscopy（FT-IR）, scanning electron microscopy（SEM）, X-ray diffraction（XRD）, thermo gravimetric analysis（TGA） and mechanical testing machine. FT-IR and SEM results show that the infrared absorption peak intensities of C-O, C-H, and C=O in aged samples decrease gradually with increasing aging time. The damage degree of surface and internal of aged samples increases gradually. XRD analysis results show that after aging treatment, the crystalline diffraction peak of thermoplastic esterified starch at 2θ = 21° disappears and the diffraction peaks of PLA at 2θ = 16.5° appear, indicating that the hydrolysis rate of esterified starch is greater than that of PLA. The crystallinity of PLA in aged sample shows an increasing trend at first followed by a decreasing one along with the increasing time of aging treatment, suggesting that the hydrolysis of amorphous regions of PLA is more preferential than its crystalline regions. Because of the influence of crystal structure and the change of composition structure, the initial decomposition temperature of aging test specimen gradually increases with the extension of aging time. The maximum decomposition rate temperature and residual mass increases at first, and then decrease after the aging time extending to 1600 h. As the aging time increases, the damage degree of combination interface between esterification starch and PLA is exacerbated, resulting in the tensile strength and bending strength of aged specimen decreasing gradually.展开更多
A decorated ruthenium catalyst was prepared by the coprecipitation method and used for the selective hydrogenation of maleic anhydride(MA) to γ-butyrolactone(GBL). The as-prepared catalyst was characterized by XRD, T...A decorated ruthenium catalyst was prepared by the coprecipitation method and used for the selective hydrogenation of maleic anhydride(MA) to γ-butyrolactone(GBL). The as-prepared catalyst was characterized by XRD, TGDTG and N2 adsorption techniques. The characterization tests revealed that the catalyst carrier was composed of monoclinic zirconia(m-ZrO2) and hydroxyl cobalt oxide(CoO(OH)). The hydrogenation results showed that the content of CoO(OH), the reaction temperature, the hydrogen pressure and the reaction time significantly affected the catalytic selectivity to GBL. The promotional effect of CoO(OH) was remarkable, which led to an obvious increase in GBL selectivity. An 100% MA conversion and 92.0% selectivity to GBL were achieved over the Ru/ZrO2-CoO(OH)(35%) catalyst in water solvent under the conditions involving a reaction temperature of 180 ℃, a hydrogen pressure of 3.0 MPa, and a reaction time of 6 h.展开更多
The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence...The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence was determined as alternating. The copolymerization rates at different feed ratios, temperatures and in different solvents were investigated, giving evidence to the very active involvement of the CT complexes in the copolymerization. Terpolymerization with acrylonitrile also showed that the complex mechanism was a proper one for this system.展开更多
基金supports for this work are the Inner Mongolia Major Science and Technology Project(No.2020ZD0024)Natural Science Foundation of Inner Mongolia(No.2024LHMS05046)+5 种基金Local Science and Technology Development Project of the Central Government(Nos.2021ZY0006 and 2022ZY0011)2023 Inner Mongolia Autonomous Region Doctoral Research Innovation Project(No.B20231023Z)Inner Mongolia Autonomous Region key Research and Technological Achievements Transformation Plan Project(No.2023YFHH0063)Autonomous Region higher education Carbon peak carbon neutral research project(No.STZX202206)Basic Scientific Research Expenses Program of Universities directly under Inner Mongolia Autonomous Region(No.JY20220043)Graphite and Graphene New Materials Discipline Team of Inner Mongolia University of Technology(No.PY202066).
文摘Paraphenylenediamine(PPDA)-grafted maleic anhydride(MAH)-modified graphene oxide(PGO)was synthesized through a dual modification process.Initially,MAH was employed to modify graphene oxide(GO)to enhance its reactive sites.Subsequently,PPDA was utilized for further modification of MAH-modified GO(MGO).Through a comprehensive analysis,the successful grafting of MAH and PPDA onto GO was confirmed.It was concurrently established that the optimal ratio of PPDA to MGO is 1:1.This approach yielded PGO characterized by outstanding dispersibility and barrier properties in epoxy resin(EP)coaings for Q235 steel.The corrosion resistance of EP coatings containing varying amounts of PGO was assessed using electrochemical workstation and salt spray testing.After immersing in a 3.5 wt.%NaCl solution for 300 h,the composite coating containing 0.1 wt.%PGO exhibited superior performance in terms of low-frequency impedance modulus,measuring at 1.1×10^(8)Ωcm^(2).The lowest corrosion current density was 2.32×10^(–10)A cm^(−2),and the self-corrosion voltage was−0.301 V.Additionally,polarization testing indicated that this coating also displayed the lowest corrosion rate,specifically 1.383×10^(–7)mm/a.
基金supported by the National Natural Science Foundation of China(21173050,21371035)SINOPEC(X514005)~~
文摘Ni/Al2O3 catalysts were derived from spinel NiAl2O4 with different Ni content ((2.5, 5 and 7.5) wt%). The catalysts were obtained by H-2 reduction and were investigated for the low-temperature hydrogenation of maleic anhydride (MA) to produce succinic anhydride (SA). The characterization results showed that Ni-0 active sites were mainly derived during the H2 reduction from spinel NiAl2O4 Among the catalysts studied, employing the optimum preparation and reaction conditions with Ni(5%)/Al2O3 yielded the highest catalytic performance. A near-100% conversion of MA and similar to 90% selectivity to SA were achieved at 120 degrees C and 0.5 MPa of H-2 with a weighted hourly space velocity (MA) of 2 h(-1). (C) 2017, Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.
基金supported by the National Science Foundation for Excellent Young Scholars of China(21922815)the Key Research and Development(R&D)Projects of Shanxi Province(201903D121180)the National Key Research and Development(R&D)Program of China。
文摘Starch,as a typical polysaccharide with natural spherical morphology,is not only a preferred precursor for preparing carbon materials but also a model polymer for investigating thermochemical evolution mechanisms.However,starch usually suffers from severe foaming and low carbon yield during direct pyrolysis.Herein,we report a simple and eco-friendly dry strategy,by maleic anhydride initiating the esterification of starch,to design carbon microspheres against the starch foaming.Moreover,the infuence of ester grafting on the pyrolytic behavior of starch is also focused.The formation of ester groups in precursor guarantees the structural stability of starch-based intermediate because it can promote the accumulation of unsaturated species and accelerate the water elimination during pyrolysis.Meanwhile,the esterification and dehydration reactions greatly deplete the primary hydroxyl groups in the starch molecules and thus the rapid levoglucosan release is inhibited,which well keeps the spherical morphology of starch and ensures the high carbon yield.In further exploration as anode materials for Lithium-ion batteries,the obtained carbon microspheres exhibit good cyclability and rate performance with a reversible capacity of 444 m Ah g^(-1)at 50 m A g^(-1).This work provides theoretical fundamentals for the controllable thermal transformation of biomass towards wide applications.
基金supported by the National Natural Science Foundation of China (Nos. 21173050 and 21371035)China Petrochemical Corporation (No. X514005)
文摘The pseudo-boehmite derived alumina supported metal（Cu,Co and Ni） catalysts prepared by the impregnation method were investigated in hydrogenation of maleic anhydride（MA） to succinic anhydride（SA） and γ-butyrolactone.The catalysts were characterized by ICP-AES,N2 adsorptiondesorption,XRD,H2-TPR,CO-TPD,dissociative N2O adsorption and TEM and the results showed that the alumina possessed mesoporous feature and the metal species were well dispersed on the support.Compared to Cu/Al2O3 and Co/Al2O3,Ni/Al2O3 exhibited higher catalytic activity in the MA hydrogenation with 92%selectivity to SA and nearly 100%conversion of MA at 140 °C under 0.5 MPa of H2 with a weighted hourly space velocity of 2 h 1（MA）.The stability of Ni/Al2O3 catalyst was also investigated.
文摘A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA’s hydrophilicity and cell affinity and to provide reactive groups for further chemical modification. FTIR, 13C NMR and DSC were used to characterize the maleic anhydride-modified PDLLA.
文摘Solid-liquid equilibria (SLE) of three binary systems and seventernary systems containing maleic an- hydride (MA) are measured byvisual method. The experimental data are compared with the calculatedones with modified universal quasichemical functional group activitycoefficient (UNIFAC) method in which the interaction parametersbetween groups come from two sources, dortmund data bank (DDB), ifthere's any, and correlations based on our former presentedexperimental SLE data of twenty binary systems.
基金financially supported by the Joint Funds of the National Natural Science Foundation of China and Guangdong Province(No.U1134005)
文摘Natural rubber grafted maleic anhydride （NR-g-MAH） was synthesized by mixing maleic anhydride （MAH） and natural rubber （NR） in solid state in a torque rheometer using dicurnyl peroxide （DCP） as initiator. Then the self-prepared NR-g-MAH was used as a compatibilizer in the natural rubber/short nylon fiber composites. Both the fimctionalization of NR with MAH and the reaction between the modified rubber and the nylon fiber were confirmed by Fourier transform infrared spectroscopy （FTIR）. Composites with different nylon short fiber loadings （0, 5, 10, 15 and 20 phr） were compounded on a two-roll mill, and the effects of the NR-g-MAH on the tensile and thermal properties, fiber-rubber interaction, as well as the morphology of the natural rubber/short nylon fiber composites were investigated. At equal fiber loading, the NR-g-MAH compatibilized NR/short nylon fiber composites showed improved tensile properties, especially the tensile modulus at 100% strain which was about 1.5 times that of the corresponding un-compatibilized ones. The equilibrium swelling tests proved that the incorporation of NR-g-MAH increased the interaction between the nylon fibers and the NR matrix. The crosslink density measured with NMR techniques showed that the NR-g-MAH compatiblized composites had lower total crosslink density. The glass transition temperatures of the compatibilized composites were about 1 K higher than that of the corresponding un-compabilized ones. Morphology analysis of the NR/short nylon fiber composites confirmed NR-g-MAH improved interfacial bonding between the NR matrix and the nylon fibers. All these results signified that the NR-g-MAH could act as a good compatilizer of NR/short nylon fiber composites and had a potential for wide use considering its easy to be prepared and compounded with the composites.
文摘In this work,the hydrogenation of maleic anhydride to succinic anhydride in the presence of 5 m%Ni/clay catalysts was investigated.These catalysts were characterized by X-ray diffraction(XRD),H2 temperature programmed reduction(TPR)and thermogravimetric analysis(TGA)techniques.The XRD and TPR studies showed that Ni was present as Ni2+on the support,which indicated that there were no elemental nickel(Ni^0)and Ni203 species in the unreduced samples.Increasing of calcination temperature to 650℃leads to destruction of the support structure observed in TGA,while the catalyst sample calcined at 550℃exhibits better performances than other samples.The ideal conversion of maleic anhydride(97.14%)and selectivity of succinic anhydride(99.55%)were realized at a reaction temperature of 180℃and a weight hourly space velocity of 4 h^-1 under a reaction pressure of 1 MPa.
基金The authors are grateful for the financial supports of the Project of Research and Development Fund of Nanchong City(19YFZJ0107,18YFZJ0041)the Meritocracy Research Funds of China West Normal University(17YC041)the Undergraduate Training Program for Innovation of China West Normal University.(cxcy2020186).
文摘The colloidal carbon microspheres(CMS)were prepared by the hydrothermal method.The nickel catalysts supported on carbon microspheres(Ni/CMS)were further prepared and were characterized by the Fourier transform infrared spectroscopy(FTIR),the X-ray diffraction(XRD),the scanning electron microscopy(SEM),the transmission electron microscopy(TEM),and the N_(2)adsorption technique.The selective hydrogenation of maleic anhydride(MA)to succinic anhydride(SA)over the Ni/CMS catalysts was investigated.The results indicated that the Ni/CMS catalyst,which was prepared with glucose as carbon source and calcined at 500℃,exhibited the best performance.The hydrogen pressure,reaction temperature,and reaction time could significantly affect the conversion of maleic anhydride during the hydrogenation reaction.A 98.4%conversion of MA and an 100%selectivity to SA were achieved over the Ni/CMS catalyst in acetic anhydride solvent under mild conditions covering a temperature of 90℃,a H2 pressure of 1.0 MPa,and a reaction time of 3 h.
基金supported by the National Natural Science Foundation,China(Nos.21506138,21606199,21575097 and21375092)the Natural Science Foundation of Zhejiang Province,China(No.LQ15B060001)the China Postdoctoral Science Foundation(No.2016M592015)
文摘Pd catalysts suffered from poor selectivity and stability for liquid-phase hydrogenation of maleic anhydride（MA） to gamma-butyrolactone（GBL）.Thus,Pd/C catalysts modified with different Sn loadings were synthesized,and characterized by XRD,XPS,TEM and elemental mapping.The types of alloy phase and the amounts of the surface Pd-SnOx sites altered along with Sn/Pd mass ratios from 0-1.0synthesized in the process of preparation.The maximum reaction rate was 0.57 mol-GBL/（mol-Pd min）and selectivity was 95.94%when the Sn/Pd mass ratio was 0.6.It might be attributed to the formation of Pd2Sn alloy and less amounts of Pd-SnOx sites.
基金financially supported by the National Natural Science Foundation of China (No.51272163)
文摘Magnesium hydroxide(MH) whiskers were modified via in situ polymerization of n-butyl acrylate and maleic anhydride. Sodium dodecyl sulfonate was used as emulsifier. The modifying effect was evaluated by using contact angle and activation index. The thermal stability,functional groups, structure, morphology, phase composition and surface element valence of MH whiskers were characterized by thermogravimetry-differential scanning calorimetry(TG-DSC), Fourier transform infrared spectroscopy(FTIR), X-ray diffraction(XRD), scanning electron microscopy(SEM) and X-ray photoelectron spectroscopy(XPS). Results reveal that the contact angle and activation index of modified MH whiskers are 105°and 76.5%, the thermal stability shows little change, and the decomposition temperature ranges between 38 and419 ℃. The copolymer of n-butyl acrylate and maleic anhydride absorbed on the surface of MH whiskers leads to the increased diameter and makes the surface of whiskers be rougher. Furthermore, the absorption of element C on the surface of MH whiskers increases, and the diffraction intensity of C 1 s spectra increases; thus, the compatibility of whiskers in the organic phase can be improved significantly. Lastly, the surface molecular model of MH whiskers modified via in situ copolymerization of n-butyl acrylate and maleic anhydride is established.
文摘The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by constant concentration of chain radicals during the copolymerization, linear evolution of molecular weights with conversion and narrow molecular weight distribution (M-w/M-n = 1.23-1.35). The compositional analysis and the sequence structural information of the copolymers obtained from DEPT (Distortionless Enhancement by Polarization Transfer) experiments demonstrate that the copolymers obtained also possess strictly alternating structure.
文摘A preliminary study of using maleic anhydride copolymer for protein binding has been carried out. The polymeric films were prepared by compression of the purified resin and annealing the film to induce efficient back formation of the anhydride groups. The properties of the film surface were analyzed by attenuated total reflection Fourier transforms infrared spectroscopy and water contact angle measurements. The protein content was determined by Bradford assay. To obtain optimum conditions, immersion time for protein binding was examined. Results revealed that proteins can be successfully immobilized onto the film surface via covalent linkage. The efficiency of the covalent binding of the extractable protein to maleic anhydride-polyethylene film was estimated at 69.87 ug/cm2, although the film had low anhydride content （3%） on the surface.
基金National Natural Science Foundation of China(No.10475010)
文摘Plasma polymerized maleic anhydride （MA） was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge （DBD）. The film properties were characterized by water contact angle （WCA）, Fourier transfer infrared （FTIR）, X-ray photoelectron spectroscopy （XPS）, atomic force microscope （AFM） analysis, and a thickness profilometer. The influence of the processing parameters on the film properties such as tile power frequency and polymerization zone was investigated. The results show that anhydride group incorporated into the growing films is favorable at the frequency of 80 kHz and working pressure of 50 Pa. The poly （maleic anhydride） film is uniform and compact at an average deposition rate of 8 nm/min.
基金Projects supported by the National Natural Science Foundation of China
文摘The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of maleic anhydride-tetrahydrofuran charge transfer complex in the chain initiation process. ESR study provides collateral evidence for the formation of maleic anhydride radical and tetrahydrofuran radical.
文摘Aim:To evaluate the safety of the long term vas occlusion with styrene maleic anhydride (SMA) and its non-invasive reversal at the level of accessory reproductive glands (ARGs) in langurs.Methods:The morphology of seminal vesicle and ventral prostate was evaluated by light as well as transmission electron microscopy.Serum clinical chemistry and urine albumin were evaluated in an autoanalyzer using reagent kits.Fructose,acid phosphatase and zinc in the seminal plasma were evaluated spectrophotometrically according to the WHO manual.Serum testosterone, prostate specific antigen and sperm antibodies were evaluated by enzyme-linked immunosorbent assays (ELISA) using reagent kits and hematology was estimated according to standard procedures.Results:The morphological features and secretory activity of the seminal vesicle and prostate were normal as evidenced by the presence of well- developed mitochondria,rough endoplasmic reticulum,Golgi bodies,secretory granules and normal nuclear charac- teristics throughout the course of investigation.Serum testosterone and prostate specific antigen remained unaltered and serum antisperm antibodies level presented negative titres.Urine albumin was nil.Total red blood corpuscles (RBC),white blood corpuscles (WBC),hemoglobin (Hb) and red cell indices,serum protein,glucose,cholesterol, creatinine,creatine kinase (CK),serum glutamate oxalate transaminase (SGOT),serum glutamate pyruvate transami- nase (SGPT),lactate dehydrogenase (LDH),bilirubin,urea,triglycerides and high-density lipoprotein (HDL) did not show appreciable changes following vas occlusion and after its non-invasive reversal.Although fructose,acid phos- phatase (ACP) and zinc in the seminal plasma showed a significant reduction following vas occlusion,it could not be related to the morphology of seminal vesicle and prostate.Conclusion:SMA vas occlusion and its non-invasive reversal do not damage the accessory reproductive organs.
基金This work was supported by the Special Fund for Major State Basic Research Projects (Grant no. G1999064803).
文摘Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP in- reactor blend granules, and solid phase graft polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.
基金Funded by the Key Laboratory of Bio-based Material Science&Technology(Northeast Forestry University)Ministry of Education(SWZCL2016-04)+1 种基金the Scientific Research Project of Hunan Provincial Education Department(15C1428)the State Bureau of Forestry 948 Project(2009-4-51)
文摘Esterified starch/polylactic acid（ES/PLA） blending composite was prepared by melting extrusion with maleic anhydride esterified starch and PLA as the raw materials. The composite was accelerated aging by using UV aging box, and its properties were characterized by Fourier transform infrared spectroscopy（FT-IR）, scanning electron microscopy（SEM）, X-ray diffraction（XRD）, thermo gravimetric analysis（TGA） and mechanical testing machine. FT-IR and SEM results show that the infrared absorption peak intensities of C-O, C-H, and C=O in aged samples decrease gradually with increasing aging time. The damage degree of surface and internal of aged samples increases gradually. XRD analysis results show that after aging treatment, the crystalline diffraction peak of thermoplastic esterified starch at 2θ = 21° disappears and the diffraction peaks of PLA at 2θ = 16.5° appear, indicating that the hydrolysis rate of esterified starch is greater than that of PLA. The crystallinity of PLA in aged sample shows an increasing trend at first followed by a decreasing one along with the increasing time of aging treatment, suggesting that the hydrolysis of amorphous regions of PLA is more preferential than its crystalline regions. Because of the influence of crystal structure and the change of composition structure, the initial decomposition temperature of aging test specimen gradually increases with the extension of aging time. The maximum decomposition rate temperature and residual mass increases at first, and then decrease after the aging time extending to 1600 h. As the aging time increases, the damage degree of combination interface between esterification starch and PLA is exacerbated, resulting in the tensile strength and bending strength of aged specimen decreasing gradually.
基金the financial support from the Natural Science Foundation of China(No.21303139)the Key Fund Project of Educational Department of Sichuan Province(No.14ZA0126)the Open Project of Chemical Synthesis and Pollution Control Key Laboratory of Sichuan Province(No.CSPC2013-1)
文摘A decorated ruthenium catalyst was prepared by the coprecipitation method and used for the selective hydrogenation of maleic anhydride(MA) to γ-butyrolactone(GBL). The as-prepared catalyst was characterized by XRD, TGDTG and N2 adsorption techniques. The characterization tests revealed that the catalyst carrier was composed of monoclinic zirconia(m-ZrO2) and hydroxyl cobalt oxide(CoO(OH)). The hydrogenation results showed that the content of CoO(OH), the reaction temperature, the hydrogen pressure and the reaction time significantly affected the catalytic selectivity to GBL. The promotional effect of CoO(OH) was remarkable, which led to an obvious increase in GBL selectivity. An 100% MA conversion and 92.0% selectivity to GBL were achieved over the Ru/ZrO2-CoO(OH)(35%) catalyst in water solvent under the conditions involving a reaction temperature of 180 ℃, a hydrogen pressure of 3.0 MPa, and a reaction time of 6 h.
基金Projects supported by the Science Fund of the Chinese Academy of Sciences
文摘The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence was determined as alternating. The copolymerization rates at different feed ratios, temperatures and in different solvents were investigated, giving evidence to the very active involvement of the CT complexes in the copolymerization. Terpolymerization with acrylonitrile also showed that the complex mechanism was a proper one for this system.
