Optimizing the orientation of β-Ga_(2)O_(3) has emerged as an effective strategy to design high-performance β-Ga_(2)O_(3) device,but the orientation growth mechanism and approach have not been revealed yet.Herein,by...Optimizing the orientation of β-Ga_(2)O_(3) has emerged as an effective strategy to design high-performance β-Ga_(2)O_(3) device,but the orientation growth mechanism and approach have not been revealed yet.Herein,by employing AlN buffer layer,the highly preferred orientation of β-Ga_(2)O_(3)(100)film rather than(-201)film is realized on 4H-SiC substrate at low sputtering power and temperature.Because β-Ga_(2)O_(3)(100)film exhibits a slower growth speed than(-201)film,the former possesses the higher dangling bond density and the lower nucleation energy,and a large conversion barrier exists between these two ori-entations.Moreover,the AlN buffer layer can suppress the surface oxidation of the 4H-SiC substrate and eliminate the strain of β-Ga_(2)O_(3)(100)film,which further reduces the nucleation energy and en-larges the conversion barrier.Meanwhile,the AlN buffer layer can increase the oxygen vacancy formation energy and decrease the oxygen vacancy concentration of β-Ga_(2)O_(3)(100)film.Consequently,the solar-blind photodetector based on the oriented film exhibits the outstanding detectivity of 1.22×10^(12) Jones and photo-to-dark current ratio of 1.11×10^(5),which are the highest among the reported β-Ga_(2)O_(3) solar-blind photodetector on the SiC substrate.Our results offer in-depth insights into the preferred orientation growth mechanism,and provide an effective way to design high-quality β-Ga_(2)O_(3)(100)orientation film and high-performance solar-blind photodetector.展开更多
Attempts to remove environmentally harmful materials in mass production industries are always a major issue and draw attention if the substitution guarantees a chance to lower fabrication cost and to improve device pe...Attempts to remove environmentally harmful materials in mass production industries are always a major issue and draw attention if the substitution guarantees a chance to lower fabrication cost and to improve device performance,as in a wide bandgap Zn_(1-x)Mg_(x)O(ZMO)to replace the CdS buffer in Cu(In_(1-x),Ga_(x))Se_(2)(CIGSe)thin-film solar cell structure.ZMO is one of the candidates for the buffer material in CIGSe thin-film solar cells with a wide and controllable bandgap depending on the Mg content,which can be helpful in attaining a suitable conduction band offset.Hence,compared to the fixed and limited bandgap of a CdS buffer,a ZMO buffer may provide advantages in V_(oc) and J_(sc) based on its controllable and wide bandgap,even with a relatively wider bandgap CIGSe thin-film solar cell.In addition,to solve problems with the defect sites at the ZMO/CIGSe junction interface,a few-nanometer ZnS layer is employed for heterojunction interface passivation,forming a ZMO/ZnS buffer structure by atomic layer deposition(ALD).Finally,a Cd-free all-dry-processed CIGSe solar cell with a wider bandgap(1.25 eV)and ALD-grown buffer structure exhibited the best power conversion efficiency of 19.1%,which exhibited a higher performance than the CdS counterpart.展开更多
The CO_2-seawater system and the method for calculating the partial pressure of CO2 (pCO2) in seawater are studied. The buffer capability of the ocean to increasing atmospheric CO2 is expressed in terms of the differe...The CO_2-seawater system and the method for calculating the partial pressure of CO2 (pCO2) in seawater are studied. The buffer capability of the ocean to increasing atmospheric CO2 is expressed in terms of the differential buffer factor and buffer index. Dissolutions of aragonite and calcite have a significant inffluence on the differential buffer factor. The trend of change in the buffer factor is obtained by a box model.展开更多
VO_2 thin films were grown on silicon substrates using Al_2O_3 thin films as the buffer layers. Compared with direct deposition on silicon, VO_2 thin films deposited on Al_2O_3 buffer layers experience a significant i...VO_2 thin films were grown on silicon substrates using Al_2O_3 thin films as the buffer layers. Compared with direct deposition on silicon, VO_2 thin films deposited on Al_2O_3 buffer layers experience a significant improvement in their microstructures and physical properties. By optimizing the growth conditions, the resistance of VO_2 thin films can change by four orders of magnitude with a reduced thermal hysteresis of 4 °C at the phase transition temperature. The electrically driven phase transformation was measured in Pt/Si/Al_2O_3/VO_2/Au heterostructures. The introduction of a buffer layer reduces the leakage current and Joule heating during electrically driven phase transitions. The C–V measurement result indicates that the phase transformation of VO_2 thin films can be induced by an electrical field.展开更多
Field-free spin-orbit torque(SOT)switching of perpendicular magnetization is essential for future spintronic devices.This study demonstrates the field-free switching of perpendicular magnetization in an HfO_(2)/Pt/Co/...Field-free spin-orbit torque(SOT)switching of perpendicular magnetization is essential for future spintronic devices.This study demonstrates the field-free switching of perpendicular magnetization in an HfO_(2)/Pt/Co/TaO_(x) structure,which is facilitated by a wedge-shaped HfO_(2)buffer layer.The field-free switching ratio varies with HfO_(2)thickness,reaching optimal performance at 25 nm.This phenomenon is attributed to the lateral anisotropy gradient of the Co layer,which is induced by the wedge-shaped HfO_(2)buffer layer.The thickness gradient of HfO_(2)along the wedge creates a corresponding lateral anisotropy gradient in the Co layer,correlating with the switching ratio.These findings indicate that field-free SOT switching can be achieved through designing buffer layer,offering a novel approach to innovating spin-orbit device.展开更多
Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP),of much interest owing to its high ionic conductivity,superior air stability,and low cost,has been regarded as one of the most promising solid-state electrolytes for next-gen...Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP),of much interest owing to its high ionic conductivity,superior air stability,and low cost,has been regarded as one of the most promising solid-state electrolytes for next-generation solid-state lithium batteries(SSLBs).Unfortunately,the commercialization of SSLBs is still impeded by severe interfacial issues,such as high interfacial impedance and poor chemical stability.Herein,we proposed a simple and convenient in-situ approach to constructing a tight and robust interface between the Li anode and LATP electrolyte via a SnO_(2)gradient buffer layer.It is firmly attached to the surface of LATP pellets due to the volume expansion of SnO_(2)when in-situ reacting with Li metal,and thus effectively alleviates the physical contact loosening during cycling,as confirmed by the mitigated impedance rising.Meanwhile,the as-formed SnO_(2)/Sn/LixSn gradient buffer layer with low electronic conductivity successfully protects the LATP electrolyte surface from erosion by the Li metal anode.Additionally,the LixSn alloy formed at the Li surface can effectively regulate uniform lithium deposition and suppress Li dendrite growth.Therefore,this work paves a new way to simultaneously address the chemical instability and poor physical contact of LATP with Li metal in developing low-cost and highly stable SSLBs.展开更多
基金supported by the National Key Research and Development Program of China(No.2021YFA0715600)the National Natural Science Foundation of China(Nos.62274125,52192611)+2 种基金the Guangdong Basic and Applied Basic Research Fund(No.2023A1515030084)the Key Research and Development Program of Shaanxi Province(Grant No.2024GX-YBXM-410)the fund of the State Key Laboratory of Solidification Processing in NWPU(No.SKLSP202220).
文摘Optimizing the orientation of β-Ga_(2)O_(3) has emerged as an effective strategy to design high-performance β-Ga_(2)O_(3) device,but the orientation growth mechanism and approach have not been revealed yet.Herein,by employing AlN buffer layer,the highly preferred orientation of β-Ga_(2)O_(3)(100)film rather than(-201)film is realized on 4H-SiC substrate at low sputtering power and temperature.Because β-Ga_(2)O_(3)(100)film exhibits a slower growth speed than(-201)film,the former possesses the higher dangling bond density and the lower nucleation energy,and a large conversion barrier exists between these two ori-entations.Moreover,the AlN buffer layer can suppress the surface oxidation of the 4H-SiC substrate and eliminate the strain of β-Ga_(2)O_(3)(100)film,which further reduces the nucleation energy and en-larges the conversion barrier.Meanwhile,the AlN buffer layer can increase the oxygen vacancy formation energy and decrease the oxygen vacancy concentration of β-Ga_(2)O_(3)(100)film.Consequently,the solar-blind photodetector based on the oriented film exhibits the outstanding detectivity of 1.22×10^(12) Jones and photo-to-dark current ratio of 1.11×10^(5),which are the highest among the reported β-Ga_(2)O_(3) solar-blind photodetector on the SiC substrate.Our results offer in-depth insights into the preferred orientation growth mechanism,and provide an effective way to design high-quality β-Ga_(2)O_(3)(100)orientation film and high-performance solar-blind photodetector.
基金conducted under the framework of the research and development program of the Korea Institute of Energy Research(C4-2412 and C4-2413)supported by the National Research Foundation of Korea(grant number 2022M3J1A1063019)funded by the Ministry of Science and ICT.
文摘Attempts to remove environmentally harmful materials in mass production industries are always a major issue and draw attention if the substitution guarantees a chance to lower fabrication cost and to improve device performance,as in a wide bandgap Zn_(1-x)Mg_(x)O(ZMO)to replace the CdS buffer in Cu(In_(1-x),Ga_(x))Se_(2)(CIGSe)thin-film solar cell structure.ZMO is one of the candidates for the buffer material in CIGSe thin-film solar cells with a wide and controllable bandgap depending on the Mg content,which can be helpful in attaining a suitable conduction band offset.Hence,compared to the fixed and limited bandgap of a CdS buffer,a ZMO buffer may provide advantages in V_(oc) and J_(sc) based on its controllable and wide bandgap,even with a relatively wider bandgap CIGSe thin-film solar cell.In addition,to solve problems with the defect sites at the ZMO/CIGSe junction interface,a few-nanometer ZnS layer is employed for heterojunction interface passivation,forming a ZMO/ZnS buffer structure by atomic layer deposition(ALD).Finally,a Cd-free all-dry-processed CIGSe solar cell with a wider bandgap(1.25 eV)and ALD-grown buffer structure exhibited the best power conversion efficiency of 19.1%,which exhibited a higher performance than the CdS counterpart.
文摘The CO_2-seawater system and the method for calculating the partial pressure of CO2 (pCO2) in seawater are studied. The buffer capability of the ocean to increasing atmospheric CO2 is expressed in terms of the differential buffer factor and buffer index. Dissolutions of aragonite and calcite have a significant inffluence on the differential buffer factor. The trend of change in the buffer factor is obtained by a box model.
基金financially supported by the National Natural Science Foundation of China (Nos. 51401046, 51572042, 61131005, 61021061, and 61271037)International Cooperation Projects (Nos. 2013HH0003 and 2015DFR50870)+3 种基金the 111 Project (No. B13042)the Sichuan Province S&T program (Nos. 2014GZ0003, 2015GZ0091, and 2015GZ0069)Fundamental Research Funds for the Central Universitiesthe start-up fund from the University of Electronic Science and Technology of China
文摘VO_2 thin films were grown on silicon substrates using Al_2O_3 thin films as the buffer layers. Compared with direct deposition on silicon, VO_2 thin films deposited on Al_2O_3 buffer layers experience a significant improvement in their microstructures and physical properties. By optimizing the growth conditions, the resistance of VO_2 thin films can change by four orders of magnitude with a reduced thermal hysteresis of 4 °C at the phase transition temperature. The electrically driven phase transformation was measured in Pt/Si/Al_2O_3/VO_2/Au heterostructures. The introduction of a buffer layer reduces the leakage current and Joule heating during electrically driven phase transitions. The C–V measurement result indicates that the phase transformation of VO_2 thin films can be induced by an electrical field.
基金Project supported by the National Natural Science Foundation of China (Grant No.12274108)the Natural Science Foundation of Zhejiang Province,China (Grant Nos.LY23A040008 and LY23A040008)the Basic Scientific Research Project of Wenzhou,China (Grant No.G20220025)。
文摘Field-free spin-orbit torque(SOT)switching of perpendicular magnetization is essential for future spintronic devices.This study demonstrates the field-free switching of perpendicular magnetization in an HfO_(2)/Pt/Co/TaO_(x) structure,which is facilitated by a wedge-shaped HfO_(2)buffer layer.The field-free switching ratio varies with HfO_(2)thickness,reaching optimal performance at 25 nm.This phenomenon is attributed to the lateral anisotropy gradient of the Co layer,which is induced by the wedge-shaped HfO_(2)buffer layer.The thickness gradient of HfO_(2)along the wedge creates a corresponding lateral anisotropy gradient in the Co layer,correlating with the switching ratio.These findings indicate that field-free SOT switching can be achieved through designing buffer layer,offering a novel approach to innovating spin-orbit device.
基金financially supported by the China Postdoctoral Science Foundation(2021M700396)the National Natural Science Foundation of China(52102206)the research grants from the National Research Foundation(2022K1A3A1A20014496 and 2022R1F1A1074707)funded by the government of the Republic of Korea。
文摘Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP),of much interest owing to its high ionic conductivity,superior air stability,and low cost,has been regarded as one of the most promising solid-state electrolytes for next-generation solid-state lithium batteries(SSLBs).Unfortunately,the commercialization of SSLBs is still impeded by severe interfacial issues,such as high interfacial impedance and poor chemical stability.Herein,we proposed a simple and convenient in-situ approach to constructing a tight and robust interface between the Li anode and LATP electrolyte via a SnO_(2)gradient buffer layer.It is firmly attached to the surface of LATP pellets due to the volume expansion of SnO_(2)when in-situ reacting with Li metal,and thus effectively alleviates the physical contact loosening during cycling,as confirmed by the mitigated impedance rising.Meanwhile,the as-formed SnO_(2)/Sn/LixSn gradient buffer layer with low electronic conductivity successfully protects the LATP electrolyte surface from erosion by the Li metal anode.Additionally,the LixSn alloy formed at the Li surface can effectively regulate uniform lithium deposition and suppress Li dendrite growth.Therefore,this work paves a new way to simultaneously address the chemical instability and poor physical contact of LATP with Li metal in developing low-cost and highly stable SSLBs.
