The simultaneous transmitting and reflecting reconfigurable intelligent surface(STAR-RIS)can independently adjust surface’s reflection and transmission coefficients so as to enhance space coverage.For a multiple-inpu...The simultaneous transmitting and reflecting reconfigurable intelligent surface(STAR-RIS)can independently adjust surface’s reflection and transmission coefficients so as to enhance space coverage.For a multiple-input multiple-output(MIMO)communication system with a STAR-RIS,a base station(BS),an eavesdropper,and multiple users,the system security rate is studied.A joint design of the power allocation at the transmitter and phase shift matrices for reflection and transmission at the STAR-RIS is conducted,in order to maximize the worst achievable security data rate(ASDR).Since the problem is nonconvex and hence challenging,a particle swarm optimization(PSO)based algorithm is developed to tackle the problem.Both the cases of continuous and discrete phase shift matrices at the STAR-RIS are considered.Simulation results demonstrate the effectiveness of the proposed algorithm and shows the benefits of using STAR-RIS in MIMO mutliuser systems.展开更多
Multiple-input multiple-output(MIMO)technology has been promoted to achieve high-speed data transmission.Compared to the orthogonal frequency division multiplexing(OFDM)based MIMO systems,the single-carrier scheme(SC)...Multiple-input multiple-output(MIMO)technology has been promoted to achieve high-speed data transmission.Compared to the orthogonal frequency division multiplexing(OFDM)based MIMO systems,the single-carrier scheme(SC)has attracted lots of attention due to its low peak-to-average ratio(PAPR)feature and is quite suitable for longdistance transmission.However,one of the significant challenges of SC-MIMO systems is the vast complexity of channel equalization and signal detection,especially for the inter-symbol interference(ISI)caused by the multipath channel.The single carrier frequency domain equalization-based minimum mean square error(SCFDE-MMSE)algorithm is proved to achieve satisfying performance.However,it involves large numbers of DFTs and large-scale matrix inversions,which is unacceptable for practical systems.In this paper,a low-complexity SCFDE-MMSE(LCSCFDE-MMSE)algorithm is proposed.Firstly,the characteristics of cyclic matrix and DFT cyclic shift are combined to reduce the number of DFTs.Secondly,SCFDE is transformed into a symbol-wise manner to avoid large-scale matrix inversions.Finally,a frequency-domain interpolation method is proposed to reduce the number of small-scale matrix inversions further.According to the evaluation results,the proposed LC-SCFDE-MMSE reduces the complexity of the traditional SCFDE-MMSE algorithm by more than one order of magnitude with less than 0.1 dB performance loss.展开更多
To improve the accuracy and efficiency of time-varying channels estimation algorithms for millimeter Wave(mmWave)massive Multiple-Input Multiple-Output(MIMO)systems in Internet of Vehicles(IoV)scenarios,the paper prop...To improve the accuracy and efficiency of time-varying channels estimation algorithms for millimeter Wave(mmWave)massive Multiple-Input Multiple-Output(MIMO)systems in Internet of Vehicles(IoV)scenarios,the paper proposes a deep learning(DL)algorithm,Squeeze-and-Excitation Attention Residual Network(SEARNet),which integrates Squeeze-and-Excitation Attention(SEAttention)mechanism and residual module.Specifically,SEARNet considers the channel information as an image matrix,and embeds a SEAttention module in residual module to construct the SEAttention-Residual block.Through a data-driven approach,SEARNet can effectively extract key information from the channel matrix using the SEAttention mechanism,thereby reducing noise interference and estimating the channel in an accurate and efficient manner.The simulation results show that compared to two traditional and two DL channel estimation algorithms,the proposed SEARNet can achieve a maximum reduction in normalized mean square error(NMSE)of 97.66%and 84.49%at SNR of-10 dB,78.18%at SNR of 5 dB,and 43.51%at SNR of 10 dB,respectively.展开更多
Intelligent reflecting surfaces(IRSs)constitute passive devices,which are capable of adjusting the phase shifts of their reflected signals,and hence they are suitable for passive beamforming.In this paper,we conceive ...Intelligent reflecting surfaces(IRSs)constitute passive devices,which are capable of adjusting the phase shifts of their reflected signals,and hence they are suitable for passive beamforming.In this paper,we conceive their design with the active beamforming action of multiple-input multipleoutput(MIMO)systems used at the access points(APs)for improving the beamforming gain,where both the APs and users are equipped with multiple antennas.Firstly,we decouple the optimization problem and design the active beamforming for a given IRS configuration.Then we transform the optimization problem of the IRS-based passive beamforming design into a tractable non-convex quadratically constrained quadratic program(QCQP).For solving the transformed problem,we give an approximate solution based on the technique of widely used semidefinite relaxation(SDR).We also propose a low-complexity iterative solution.We further prove that it can converge to a locally optimal value.Finally,considering the practical scenario of discrete phase shifts at the IRS,we give the quantization design for IRS elements on basis of the two solutions.Our simulation results demonstrate the superiority of the proposed solutions over the relevant benchmarks.展开更多
A novel framework of which combines smart antennas multiple antenna systems, （SA） with multiple-input multiple-output （MIMO） at the receiver, is proposed. The uplink SA-MIMO system is investigated. The joint optim...A novel framework of which combines smart antennas multiple antenna systems, （SA） with multiple-input multiple-output （MIMO） at the receiver, is proposed. The uplink SA-MIMO system is investigated. The joint optimization problem corresponding to the uplink capacity of the single-user SA-MIMO system is deduced. Then the closedform expression of the capacity is obtained in the case of equal power allocation and the same direction-of-arrivals （DOAs） from different transmit antennas at the same antenna array, and an upper bound of the capacity is also given in the case of different DOAs at the same antenna array. After that, for the general case, a suboptimal method for the capacity optimization problem is presented. Some numerical results are also given to compare the capacities of conventional MIMO and SA-MIMO systems and show that the proposed method is viable.展开更多
New conditions are derived for the l2-stability of time-varying linear and nonlinear discrete-time multiple-input multipleoutput （MIMO） systems, having a linear time time-invariant block with the transfer function F...New conditions are derived for the l2-stability of time-varying linear and nonlinear discrete-time multiple-input multipleoutput （MIMO） systems, having a linear time time-invariant block with the transfer function F（z）, in negative feedback with a matrix of periodic/aperiodic gains A（k）, k = 0,1, 2,... and a vector of certain classes of non-monotone/monotone nonlinearities φp（-）, without restrictions on their slopes and also not requiring path-independence of their line integrals. The stability conditions, which are derived in the frequency domain, have the following features： i） They involve the positive definiteness of the real part （as evaluated on ｜z｜ = 1） of the product of Г （z） and a matrix multiplier function of z. ii） For periodic A（k）, one class of multiplier functions can be chosen so as to impose no constraint on the rate of variations A（k）, but for aperiodic A（k）, which allows a more general multiplier function, constraints are imposed on certain global averages of the generalized eigenvalues of （A（k ＋ 1）,A（k））, k = 1, 2 iii） They are distinct from and less restrictive than recent results in the literature.展开更多
Adaptive modulation (AM) is an effective technique to approach the theoretical bound of multi-input and multi-output (MIMO) channel. In most previous studies, the AM parameters were obtained by maximizing the transmis...Adaptive modulation (AM) is an effective technique to approach the theoretical bound of multi-input and multi-output (MIMO) channel. In most previous studies, the AM parameters were obtained by maximizing the transmission rate for a given total transmit power. In this paper, a novel AM-MIMO algorithm is presented, which is based on minimizing total transmit power when the link’s QoS requirements are given. By taking the QoS requirements into account directly, the proposed algorithm not only makes the system more flexible, but also makes the cross layer design of wireless network easier. At last, the numerical results of the proposed scheme are presented.展开更多
A novel method to extract multiple input and multiple output (MIMO) chaotic signals was proposed using the blind neural algorithm after transmitting in nonideal channel. The MIMO scheme with different chaotic signal g...A novel method to extract multiple input and multiple output (MIMO) chaotic signals was proposed using the blind neural algorithm after transmitting in nonideal channel. The MIMO scheme with different chaotic signal generators was presented. In order to separate the chaotic source signals only by using the sensor signals at receivers, a blind neural extraction algorithm based on higher-order statistic (HOS) technique was used to recover the primary chaotic signals. Simulation results show that the proposed approach has good performance in separating the primary chaotic signals even under nonideal channel.展开更多
An antenna selection algorithm based on large-scale fading between the transmitter and receiver is proposed for the uplink receive antenna selection in distributed multiple-input multiple-output(D-MIMO) systems. By ut...An antenna selection algorithm based on large-scale fading between the transmitter and receiver is proposed for the uplink receive antenna selection in distributed multiple-input multiple-output(D-MIMO) systems. By utilizing the radio access units(RAU) selection based on large-scale fading,the proposed algorithm decreases enormously the computational complexity. Based on the characteristics of distributed systems,an improved particle swarm optimization(PSO) has been proposed for the antenna selection after the RAU selection. In order to apply the improved PSO algorithm better in antenna selection,a general form of channel capacity was transformed into a binary expression by analyzing the formula of channel capacity. The proposed algorithm can make full use of the advantages of D-MIMO systems,and achieve near-optimal performance in terms of channel capacity with low computational complexity.展开更多
Signal detection plays an essential role in massive Multiple-Input Multiple-Output(MIMO)systems.However,existing detection methods have not yet made a good tradeoff between Bit Error Rate(BER)and computational complex...Signal detection plays an essential role in massive Multiple-Input Multiple-Output(MIMO)systems.However,existing detection methods have not yet made a good tradeoff between Bit Error Rate(BER)and computational complexity,resulting in slow convergence or high complexity.To address this issue,a low-complexity Approximate Message Passing(AMP)detection algorithm with Deep Neural Network(DNN)(denoted as AMP-DNN)is investigated in this paper.Firstly,an efficient AMP detection algorithm is derived by scalarizing the simplification of Belief Propagation(BP)algorithm.Secondly,by unfolding the obtained AMP detection algorithm,a DNN is specifically designed for the optimal performance gain.For the proposed AMP-DNN,the number of trainable parameters is only related to that of layers,regardless of modulation scheme,antenna number and matrix calculation,thus facilitating fast and stable training of the network.In addition,the AMP-DNN can detect different channels under the same distribution with only one training.The superior performance of the AMP-DNN is also verified by theoretical analysis and experiments.It is found that the proposed algorithm enables the reduction of BER without signal prior information,especially in the spatially correlated channel,and has a lower computational complexity compared with existing state-of-the-art methods.展开更多
In millimeter wave(mmWave) multiple-input multiple-output(MIMO) systems, hybrid precoding has been widely used to overcome the severe propagation loss. In order to improve the spectrum efficiency with low complexity, ...In millimeter wave(mmWave) multiple-input multiple-output(MIMO) systems, hybrid precoding has been widely used to overcome the severe propagation loss. In order to improve the spectrum efficiency with low complexity, we propose a joint hybrid precoding algorithm for single-user mmWave MIMO systems in this paper. By using the concept of equivalent channel, the proposed algorithm skillfully utilizes the idea of alternating optimization to complete the design of RF precoder and combiner. Then, the baseband precoder and combiner are computed by calculating the singular value decomposition of the equivalent channel. Simulation results demonstrate that the proposed algorithm can achieve satisfactory performance with quite low complexity. Moreover, we investigate the effects of quantization on the analog components and find that the proposed scheme is effective even with coarse quantization.展开更多
In this paper, the performance of hybrid precoding is investigated for mmWave massive MIMO systems with different antenna arrays. The hybrid precoding with partially connected architecture (PCA) is adopted. The spectr...In this paper, the performance of hybrid precoding is investigated for mmWave massive MIMO systems with different antenna arrays. The hybrid precoding with partially connected architecture (PCA) is adopted. The spectral efficiency (SE) and received energy efficiency (EE) are investigated by considering four types of antenna arrays, including uniform linear array (ULA), uniform rectangular planar array (URPA), uniform hexagonal planar array (UHPA), and uniform circular planar array (UCPA), respectively. We focus on analysis at the antenna response vector and utilize the idea of orthogonal matching pursuit algorithm to seek the optimal hybrid precoder. Furthermore, the trade-off of precoding architectures is studied between SE and received EE. Simulation results show that if the uniform planar array antenna is more concentrated, the SE and receive EE will be higher. Considering SE and received EE, the performance of planar arrays outperform linear array. There exist different optimal radio-frequency chain numbers to maximize the SE for planar array and linear array. In addition, the PCA can achieve relatively higher received EE while the SE is close to the fully connected architecture and the full digital architecture.展开更多
This paper investigates the achievable uplink spectral efficiency(SE) of a massive multi-input multi-output(MIMO) system with a mixed analog-to-digital converter(ADC) receiver architecture, in which some antennas are ...This paper investigates the achievable uplink spectral efficiency(SE) of a massive multi-input multi-output(MIMO) system with a mixed analog-to-digital converter(ADC) receiver architecture, in which some antennas are equipped with full-resolution ADCs while others are deployed with low-resolution ADCs. We derive the theoretical results and corresponding approximate expressions of the achievable SE in multi-cell systems with maximum ratio combining(MRC) detector and in single-cell systems with zero-forcing(ZF) detector. Based on approximated results, the effects of physical parameters, including the transmit power, the number of antennas, the proportion of full-resolution ADCs and the quantization precision of the low-resolution ADCs on the achievable SE are revealed. Furthermore, we propose the power allocation algorithms based on the lower bound and upper bound of approximate achievable SE. Our results show that the total achievable SE improves by increasing the number of BS antennas, the signal-to-noise ratio(SNR), and the quantization precision. Results showcase that proposed power allocation algorithms remarkably improve the total achievable SE comparing to the equal power allocation algorithm, which verifies the effectiveness of our proposed schemes.展开更多
Millimeter wave(mmWave) and large-scale multiple input multiple output(MIMO) are two emerging technologies in fifth-generation wireless communication systems. The power consumption and hardware cost of radio frequency...Millimeter wave(mmWave) and large-scale multiple input multiple output(MIMO) are two emerging technologies in fifth-generation wireless communication systems. The power consumption and hardware cost of radio frequency(RF) chains increase exponentially with the bit resolution of analog-to-digital converters(ADCs) and digital-to-analog converters(DACs). One promising solution is to employ few RF chains with low-bit ADCs and DACs. In this paper, we consider mmWave large-scale MIMO systems with low bits DACs and ADCs. Leveraging on the Bussgang theorem and the additive quantization noise model(AQNM), a closed-form expression of the achievable rate is derived to show the effect of the ADCs? and DACs? resolution. Moreover, an orthogonal matching pursuit(OMP) based hybrid precoding algorithm is proposed to increase the achievable rate. Our results show that the impact of DACs is more pronounced than the impact of ADCs. Furthermore, 5-bit ADCs and DACs are sufficient at the transceiver to operate without a significant performance loss.展开更多
Network-assisted full duplex(NAFD)cellfree(CF)massive MIMO has drawn increasing attention in 6G evolvement.In this paper,we build an NAFD CF system in which the users and access points(APs)can flexibly select their du...Network-assisted full duplex(NAFD)cellfree(CF)massive MIMO has drawn increasing attention in 6G evolvement.In this paper,we build an NAFD CF system in which the users and access points(APs)can flexibly select their duplex modes to increase the link spectral efficiency.Then we formulate a joint flexible duplexing and power allocation problem to balance the user fairness and system spectral efficiency.We further transform the problem into a probability optimization to accommodate the shortterm communications.In contrast with the instant performance optimization,the probability optimization belongs to a sequential decision making problem,and thus we reformulate it as a Markov Decision Process(MDP).We utilizes deep reinforcement learning(DRL)algorithm to search the solution from a large state-action space,and propose an asynchronous advantage actor-critic(A3C)-based scheme to reduce the chance of converging to the suboptimal policy.Simulation results demonstrate that the A3C-based scheme is superior to the baseline schemes in term of the complexity,accumulated log spectral efficiency,and stability.展开更多
This paper studies the achievable spectral efficiency(SE)of downlink multiuser multiple-input-multiple-output(MIMO)system,where the base station(BS)is deployed an arbitrary finite antenna number and communicates simul...This paper studies the achievable spectral efficiency(SE)of downlink multiuser multiple-input-multiple-output(MIMO)system,where the base station(BS)is deployed an arbitrary finite antenna number and communicates simultaneously with many users. We assume that the BS has accurate channel state information(CSI)and adopt maximum ratio transmission(MRT)precoding. An accurate analytical result for the achievable SE is obtained. Based on the analytical result on the achievable SE,we further study the achievable energy efficiency(EE)of multiuser MIMO system by considering an energy consumption model. Results indicate that the increasing number of BS antennas can boost the achievable SE of system,whilst the achievable SE tends to a saturated rate in the high signal-tonoise ratios(SNR)regime. Furthermore,an important conclusion is that the increasing number of users is beneficial for the achievable EE and there is an optimal antenna number to maximize the EE of system.展开更多
Minimum mean square error(MMSE) detection algorithm can achieve nearly optimal performance when the number of antennas at the base station(BS) is large enough compared to the number of users. But the traditional MMSE ...Minimum mean square error(MMSE) detection algorithm can achieve nearly optimal performance when the number of antennas at the base station(BS) is large enough compared to the number of users. But the traditional MMSE involves complicated matrix inversion. In this paper, we propose a modified MMSE algorithm which exploits the channel characteristics occurring in massive multiple-input multipleoutput(MIMO) channels and the relaxation iteration(RI) method to avoid the matrix inversion. A proper initial solution is given to accelerate the convergence speed. In addition, we point out that the channel estimation scheme used in channel hardening-exploiting message passing(CHEMP) receiver is very appropriate for our proposed detection algorithm. Simulation results verify that the proposed algorithm can achieve very close performance of the traditional MMSE algorithm with a small number of iterations.展开更多
With a low resolution 1-bit ADC on its receiver(RX) side, MIMO with 1-bit ADC took a considerable step in the fulfillment of the hardware complexity constrains of the internet of things(IoT) PHY layer design. However,...With a low resolution 1-bit ADC on its receiver(RX) side, MIMO with 1-bit ADC took a considerable step in the fulfillment of the hardware complexity constrains of the internet of things(IoT) PHY layer design. However, applying 1-bit ADC at MIMO RX results in severe nonlinear quantization error. By which, almost all received signal amplitude information is completely distorted. Thus, MIMO channel estimation is considered as a major barrier towards practical realization of 1-bit ADC MIMO system. In this paper, two efficient sparsity-based channel estimation techniques are proposed for 1-bit ADC MIMO systems, namely the low complexity sparsity-based channel estimation(LCSCE), and the iterative adaptive sparsity channel estimation(IASCE). In these techniques, the sparsity of the 1-bit ADC MIMO channel is exploited to propose a new adaptive and iterative compressive sensing(CS) recovery algorithm to handle the 1-bit ADC quantization effect. The proposed algorithms are tested with the state-of-the-art 1-bit ADC MIMO constant envelope modulation(MIMO-CEM). The 1-bit ADC MIMO-CEM system is chosen as it fulfills both energy and hardware complexity constraints of the IoT PHY layer. Simulation results reveal the high effectiveness of the proposed algorithms in terms of spectral efficiency(SE) and computational complexity. The proposed LCSCE reduces the computational complexity of the 1-bit ADC MIMO-CEM channel estimation by 86%, while the IASCE reduces it by 96% compared to the recent techniques of MIMO-CEM channel estimation. Moreover, the proposed LCSCE and IASCE improve the spectrum efficiency by 76 % and 73 %, respectively, compared to the recent techniques.展开更多
In this paper,the performance of uplink multiuser massive multiple-input multipleoutput(MIMO)system with spatial modulation over transmit-correlated Rayleigh fading channel is investigated,where a large number of ante...In this paper,the performance of uplink multiuser massive multiple-input multipleoutput(MIMO)system with spatial modulation over transmit-correlated Rayleigh fading channel is investigated,where a large number of antennas are deployed at the base station and linear zero-forcing(ZF)receiver is employed for detection.By taking the transmit correlation and the randomness of shadow fading in to account,the bit error rate(BER)performance of the system is analyzed.According to the performance analysis,an approximated expression of overall average BER of the system is attained.Besides,asymptotic performance is studied and the corresponding BER expression at high signal-to-noise ratio is derived.On this basis,the diversity gain of the system can be obtained for performance evaluation.Simulation results show that the derived theoretical expressions match the simulated values well,which verifies the correctness of our analysis.展开更多
Energy efficiency(EE)is a critical design when taking into account circuit power consumption(CPC)in fifth-generation cellular networks.These problems arise because of the increasing number of antennas in massive multi...Energy efficiency(EE)is a critical design when taking into account circuit power consumption(CPC)in fifth-generation cellular networks.These problems arise because of the increasing number of antennas in massive multiple-input multiple-output(MIMO)systems,attributable to inter-cell interference for channel state information.Apart from that,a higher number of radio frequency(RF)chains at the base station and active users consume more power due to the processing activities in digital-to-analogue converters and power amplifiers.Therefore,antenna selection,user selection,optimal transmission power,and pilot reuse power are important aspects in improving energy efficiency in massive MIMO systems.This work aims to investigate joint antenna selection,optimal transmit power and joint user selection based on deriving the closed-form of the maximal EE,with complete knowledge of large-scale fading with maximum ratio transmission.It also accounts for channel estimation and eliminating pilot contamination as antennas M→∞.This formulates the optimization problem of joint optimal antenna selection,transmits power allocation and joint user selection to mitigate inter-cellinterference in downlink multi-cell massive MIMO systems under minimized reuse of pilot sequences based on a novel iterative low-complexity algorithm(LCA)for Newton’s methods and Lagrange multipliers.To analyze the precise power consumption,a novel power consumption scheme is proposed for each individual antenna,based on the transmit power amplifier and CPC.Simulation results demonstrate that the maximal EE was achieved using the iterative LCA based on reasonable maximum transmit power,in the case the noise power is less than the received power pilot.The maximum EE was achieved with the desired maximum transmit power threshold by minimizing pilot reuse,in the case the transmit power allocationρd=40 dBm,and the optimal EE=71.232 Mb/j.展开更多
文摘The simultaneous transmitting and reflecting reconfigurable intelligent surface(STAR-RIS)can independently adjust surface’s reflection and transmission coefficients so as to enhance space coverage.For a multiple-input multiple-output(MIMO)communication system with a STAR-RIS,a base station(BS),an eavesdropper,and multiple users,the system security rate is studied.A joint design of the power allocation at the transmitter and phase shift matrices for reflection and transmission at the STAR-RIS is conducted,in order to maximize the worst achievable security data rate(ASDR).Since the problem is nonconvex and hence challenging,a particle swarm optimization(PSO)based algorithm is developed to tackle the problem.Both the cases of continuous and discrete phase shift matrices at the STAR-RIS are considered.Simulation results demonstrate the effectiveness of the proposed algorithm and shows the benefits of using STAR-RIS in MIMO mutliuser systems.
基金supported by National Natural Science Foundation of China(Grant Number:62371099).
文摘Multiple-input multiple-output(MIMO)technology has been promoted to achieve high-speed data transmission.Compared to the orthogonal frequency division multiplexing(OFDM)based MIMO systems,the single-carrier scheme(SC)has attracted lots of attention due to its low peak-to-average ratio(PAPR)feature and is quite suitable for longdistance transmission.However,one of the significant challenges of SC-MIMO systems is the vast complexity of channel equalization and signal detection,especially for the inter-symbol interference(ISI)caused by the multipath channel.The single carrier frequency domain equalization-based minimum mean square error(SCFDE-MMSE)algorithm is proved to achieve satisfying performance.However,it involves large numbers of DFTs and large-scale matrix inversions,which is unacceptable for practical systems.In this paper,a low-complexity SCFDE-MMSE(LCSCFDE-MMSE)algorithm is proposed.Firstly,the characteristics of cyclic matrix and DFT cyclic shift are combined to reduce the number of DFTs.Secondly,SCFDE is transformed into a symbol-wise manner to avoid large-scale matrix inversions.Finally,a frequency-domain interpolation method is proposed to reduce the number of small-scale matrix inversions further.According to the evaluation results,the proposed LC-SCFDE-MMSE reduces the complexity of the traditional SCFDE-MMSE algorithm by more than one order of magnitude with less than 0.1 dB performance loss.
基金supported in part by the National Natural Science Foundation of China under Grants U2001213 and 62261024in part by National Key Research and Development Project under Grant 2020YFB1807204in part by Key Laboratory of Universal Wireless Communications(BUPT),Ministry of Education under Grant KFKT2022101.
文摘To improve the accuracy and efficiency of time-varying channels estimation algorithms for millimeter Wave(mmWave)massive Multiple-Input Multiple-Output(MIMO)systems in Internet of Vehicles(IoV)scenarios,the paper proposes a deep learning(DL)algorithm,Squeeze-and-Excitation Attention Residual Network(SEARNet),which integrates Squeeze-and-Excitation Attention(SEAttention)mechanism and residual module.Specifically,SEARNet considers the channel information as an image matrix,and embeds a SEAttention module in residual module to construct the SEAttention-Residual block.Through a data-driven approach,SEARNet can effectively extract key information from the channel matrix using the SEAttention mechanism,thereby reducing noise interference and estimating the channel in an accurate and efficient manner.The simulation results show that compared to two traditional and two DL channel estimation algorithms,the proposed SEARNet can achieve a maximum reduction in normalized mean square error(NMSE)of 97.66%and 84.49%at SNR of-10 dB,78.18%at SNR of 5 dB,and 43.51%at SNR of 10 dB,respectively.
基金supported in part by the the National Key Research and Development Program of China under No.2019YFB1803200by the National Natural Science Foundation of China(NSFC)under Grant 61620106001 and 61901034.
文摘Intelligent reflecting surfaces(IRSs)constitute passive devices,which are capable of adjusting the phase shifts of their reflected signals,and hence they are suitable for passive beamforming.In this paper,we conceive their design with the active beamforming action of multiple-input multipleoutput(MIMO)systems used at the access points(APs)for improving the beamforming gain,where both the APs and users are equipped with multiple antennas.Firstly,we decouple the optimization problem and design the active beamforming for a given IRS configuration.Then we transform the optimization problem of the IRS-based passive beamforming design into a tractable non-convex quadratically constrained quadratic program(QCQP).For solving the transformed problem,we give an approximate solution based on the technique of widely used semidefinite relaxation(SDR).We also propose a low-complexity iterative solution.We further prove that it can converge to a locally optimal value.Finally,considering the practical scenario of discrete phase shifts at the IRS,we give the quantization design for IRS elements on basis of the two solutions.Our simulation results demonstrate the superiority of the proposed solutions over the relevant benchmarks.
基金The National Science and Technology Major Projects(No.2010ZX03003-002,2010ZX03003-004)the National Natural Science Foundation of China(No.60972023)+1 种基金Research Fund of National Mobile Communications Research Laboratory of Southeast University(No.2011A06)the Fund of UK-China Science Bridge
文摘A novel framework of which combines smart antennas multiple antenna systems, （SA） with multiple-input multiple-output （MIMO） at the receiver, is proposed. The uplink SA-MIMO system is investigated. The joint optimization problem corresponding to the uplink capacity of the single-user SA-MIMO system is deduced. Then the closedform expression of the capacity is obtained in the case of equal power allocation and the same direction-of-arrivals （DOAs） from different transmit antennas at the same antenna array, and an upper bound of the capacity is also given in the case of different DOAs at the same antenna array. After that, for the general case, a suboptimal method for the capacity optimization problem is presented. Some numerical results are also given to compare the capacities of conventional MIMO and SA-MIMO systems and show that the proposed method is viable.
文摘New conditions are derived for the l2-stability of time-varying linear and nonlinear discrete-time multiple-input multipleoutput （MIMO） systems, having a linear time time-invariant block with the transfer function F（z）, in negative feedback with a matrix of periodic/aperiodic gains A（k）, k = 0,1, 2,... and a vector of certain classes of non-monotone/monotone nonlinearities φp（-）, without restrictions on their slopes and also not requiring path-independence of their line integrals. The stability conditions, which are derived in the frequency domain, have the following features： i） They involve the positive definiteness of the real part （as evaluated on ｜z｜ = 1） of the product of Г （z） and a matrix multiplier function of z. ii） For periodic A（k）, one class of multiplier functions can be chosen so as to impose no constraint on the rate of variations A（k）, but for aperiodic A（k）, which allows a more general multiplier function, constraints are imposed on certain global averages of the generalized eigenvalues of （A（k ＋ 1）,A（k））, k = 1, 2 iii） They are distinct from and less restrictive than recent results in the literature.
基金Project (Nos. 60272082 and 60372076) supported by the NationalNatural Science Foundation of China
文摘Adaptive modulation (AM) is an effective technique to approach the theoretical bound of multi-input and multi-output (MIMO) channel. In most previous studies, the AM parameters were obtained by maximizing the transmission rate for a given total transmit power. In this paper, a novel AM-MIMO algorithm is presented, which is based on minimizing total transmit power when the link’s QoS requirements are given. By taking the QoS requirements into account directly, the proposed algorithm not only makes the system more flexible, but also makes the cross layer design of wireless network easier. At last, the numerical results of the proposed scheme are presented.
基金The Science and Technology Committee of Shanghai Municipality (No. 05DZ15004, 06DZ15013)The Project-sponsored by SRF for ROCS, SEM
文摘A novel method to extract multiple input and multiple output (MIMO) chaotic signals was proposed using the blind neural algorithm after transmitting in nonideal channel. The MIMO scheme with different chaotic signal generators was presented. In order to separate the chaotic source signals only by using the sensor signals at receivers, a blind neural extraction algorithm based on higher-order statistic (HOS) technique was used to recover the primary chaotic signals. Simulation results show that the proposed approach has good performance in separating the primary chaotic signals even under nonideal channel.
基金Supported by the National Natural Science Foundation of China(No.61201086,61272495)the China Scholarship Council(No.201506375060)+1 种基金the Planned Science and Technology Project of Guangdong Province(No.2013B090500007) the Dongguan Project on the Integration of Industry,Education and Research(No.2014509102205)
文摘An antenna selection algorithm based on large-scale fading between the transmitter and receiver is proposed for the uplink receive antenna selection in distributed multiple-input multiple-output(D-MIMO) systems. By utilizing the radio access units(RAU) selection based on large-scale fading,the proposed algorithm decreases enormously the computational complexity. Based on the characteristics of distributed systems,an improved particle swarm optimization(PSO) has been proposed for the antenna selection after the RAU selection. In order to apply the improved PSO algorithm better in antenna selection,a general form of channel capacity was transformed into a binary expression by analyzing the formula of channel capacity. The proposed algorithm can make full use of the advantages of D-MIMO systems,and achieve near-optimal performance in terms of channel capacity with low computational complexity.
基金supported by Major Project of Science and Technology Research Program of Chongqing Education Commission of China(Grant No.KJZD-M201900601)China Postdoctoral Science Foundation(Grant No.2021MD703932)Project Supported by Engineering Research Center of Mobile Communications,Ministry of Education,China(Grant No.cqupt-mct-202006)。
文摘Signal detection plays an essential role in massive Multiple-Input Multiple-Output(MIMO)systems.However,existing detection methods have not yet made a good tradeoff between Bit Error Rate(BER)and computational complexity,resulting in slow convergence or high complexity.To address this issue,a low-complexity Approximate Message Passing(AMP)detection algorithm with Deep Neural Network(DNN)(denoted as AMP-DNN)is investigated in this paper.Firstly,an efficient AMP detection algorithm is derived by scalarizing the simplification of Belief Propagation(BP)algorithm.Secondly,by unfolding the obtained AMP detection algorithm,a DNN is specifically designed for the optimal performance gain.For the proposed AMP-DNN,the number of trainable parameters is only related to that of layers,regardless of modulation scheme,antenna number and matrix calculation,thus facilitating fast and stable training of the network.In addition,the AMP-DNN can detect different channels under the same distribution with only one training.The superior performance of the AMP-DNN is also verified by theoretical analysis and experiments.It is found that the proposed algorithm enables the reduction of BER without signal prior information,especially in the spatially correlated channel,and has a lower computational complexity compared with existing state-of-the-art methods.
基金supported by NSFC (No. 61571055)fund of SKL of MMW (No. K201815) Important National Science & Technology Specific Projects (2017ZX03001028)
文摘In millimeter wave(mmWave) multiple-input multiple-output(MIMO) systems, hybrid precoding has been widely used to overcome the severe propagation loss. In order to improve the spectrum efficiency with low complexity, we propose a joint hybrid precoding algorithm for single-user mmWave MIMO systems in this paper. By using the concept of equivalent channel, the proposed algorithm skillfully utilizes the idea of alternating optimization to complete the design of RF precoder and combiner. Then, the baseband precoder and combiner are computed by calculating the singular value decomposition of the equivalent channel. Simulation results demonstrate that the proposed algorithm can achieve satisfactory performance with quite low complexity. Moreover, we investigate the effects of quantization on the analog components and find that the proposed scheme is effective even with coarse quantization.
基金supported by the National Natural Science Foundation of China (No.61961018)the Jiangxi Province Foundation for Distinguished Young Scholar (No.20192BCB23013)+1 种基金the Jiangxi Province Natural Science Foundation of China (No.20171BAB202001, 20192ACB21003)the Science Program of Jiangxi Educational Committee (No.GJJ180307)
文摘In this paper, the performance of hybrid precoding is investigated for mmWave massive MIMO systems with different antenna arrays. The hybrid precoding with partially connected architecture (PCA) is adopted. The spectral efficiency (SE) and received energy efficiency (EE) are investigated by considering four types of antenna arrays, including uniform linear array (ULA), uniform rectangular planar array (URPA), uniform hexagonal planar array (UHPA), and uniform circular planar array (UCPA), respectively. We focus on analysis at the antenna response vector and utilize the idea of orthogonal matching pursuit algorithm to seek the optimal hybrid precoder. Furthermore, the trade-off of precoding architectures is studied between SE and received EE. Simulation results show that if the uniform planar array antenna is more concentrated, the SE and receive EE will be higher. Considering SE and received EE, the performance of planar arrays outperform linear array. There exist different optimal radio-frequency chain numbers to maximize the SE for planar array and linear array. In addition, the PCA can achieve relatively higher received EE while the SE is close to the fully connected architecture and the full digital architecture.
基金supported in part by the National Science Foundation(NSFC)for Distinguished Young Scholars of China with Grant 61625106the National Natural Science Foundation of China under Grant 61531011+1 种基金the Hong Kong,Macao and Taiwan Science and Technology Cooperation Program of China(2016YFE0123100)the Guangzhou University project under Grant 27000503123
文摘This paper investigates the achievable uplink spectral efficiency(SE) of a massive multi-input multi-output(MIMO) system with a mixed analog-to-digital converter(ADC) receiver architecture, in which some antennas are equipped with full-resolution ADCs while others are deployed with low-resolution ADCs. We derive the theoretical results and corresponding approximate expressions of the achievable SE in multi-cell systems with maximum ratio combining(MRC) detector and in single-cell systems with zero-forcing(ZF) detector. Based on approximated results, the effects of physical parameters, including the transmit power, the number of antennas, the proportion of full-resolution ADCs and the quantization precision of the low-resolution ADCs on the achievable SE are revealed. Furthermore, we propose the power allocation algorithms based on the lower bound and upper bound of approximate achievable SE. Our results show that the total achievable SE improves by increasing the number of BS antennas, the signal-to-noise ratio(SNR), and the quantization precision. Results showcase that proposed power allocation algorithms remarkably improve the total achievable SE comparing to the equal power allocation algorithm, which verifies the effectiveness of our proposed schemes.
基金supported in part by the National Key R&D Program of China (No. 2016YFE0200900)Major Projects of Beijing Municipal Science and Technology Commission (No. Z181100003218010)+3 种基金National Natural Science Foundation of China (Nos. 61601020, 61725101 and U1834210)the Beijing Natural Science Foundation (Nos. 4182049, L171005 and L172020)the open research fund of National Mobile Communications Research Laboratory, Southeast University (No. 2018D04)Key Laboratory of Optical Communication and Networks (No. KLOCN2018002)
文摘Millimeter wave(mmWave) and large-scale multiple input multiple output(MIMO) are two emerging technologies in fifth-generation wireless communication systems. The power consumption and hardware cost of radio frequency(RF) chains increase exponentially with the bit resolution of analog-to-digital converters(ADCs) and digital-to-analog converters(DACs). One promising solution is to employ few RF chains with low-bit ADCs and DACs. In this paper, we consider mmWave large-scale MIMO systems with low bits DACs and ADCs. Leveraging on the Bussgang theorem and the additive quantization noise model(AQNM), a closed-form expression of the achievable rate is derived to show the effect of the ADCs? and DACs? resolution. Moreover, an orthogonal matching pursuit(OMP) based hybrid precoding algorithm is proposed to increase the achievable rate. Our results show that the impact of DACs is more pronounced than the impact of ADCs. Furthermore, 5-bit ADCs and DACs are sufficient at the transceiver to operate without a significant performance loss.
基金supported by the National Key R&D Program of China under Grant 2020YFB1807204the BUPT Excellent Ph.D.Students Foundation under Grant CX2022306。
文摘Network-assisted full duplex(NAFD)cellfree(CF)massive MIMO has drawn increasing attention in 6G evolvement.In this paper,we build an NAFD CF system in which the users and access points(APs)can flexibly select their duplex modes to increase the link spectral efficiency.Then we formulate a joint flexible duplexing and power allocation problem to balance the user fairness and system spectral efficiency.We further transform the problem into a probability optimization to accommodate the shortterm communications.In contrast with the instant performance optimization,the probability optimization belongs to a sequential decision making problem,and thus we reformulate it as a Markov Decision Process(MDP).We utilizes deep reinforcement learning(DRL)algorithm to search the solution from a large state-action space,and propose an asynchronous advantage actor-critic(A3C)-based scheme to reduce the chance of converging to the suboptimal policy.Simulation results demonstrate that the A3C-based scheme is superior to the baseline schemes in term of the complexity,accumulated log spectral efficiency,and stability.
基金supported by the National Natural Science Foundation of China under Grants 61531011 and 61450110445the International Science and Technology Cooperation Program of China under Grant 2014DFT10300 and China Scholarship Council
文摘This paper studies the achievable spectral efficiency(SE)of downlink multiuser multiple-input-multiple-output(MIMO)system,where the base station(BS)is deployed an arbitrary finite antenna number and communicates simultaneously with many users. We assume that the BS has accurate channel state information(CSI)and adopt maximum ratio transmission(MRT)precoding. An accurate analytical result for the achievable SE is obtained. Based on the analytical result on the achievable SE,we further study the achievable energy efficiency(EE)of multiuser MIMO system by considering an energy consumption model. Results indicate that the increasing number of BS antennas can boost the achievable SE of system,whilst the achievable SE tends to a saturated rate in the high signal-tonoise ratios(SNR)regime. Furthermore,an important conclusion is that the increasing number of users is beneficial for the achievable EE and there is an optimal antenna number to maximize the EE of system.
基金supported by the National Hightech R&D Program of China(2014AA01A704)the Natural Science Foundation of China(61201135)111 Project(B08038)
文摘Minimum mean square error(MMSE) detection algorithm can achieve nearly optimal performance when the number of antennas at the base station(BS) is large enough compared to the number of users. But the traditional MMSE involves complicated matrix inversion. In this paper, we propose a modified MMSE algorithm which exploits the channel characteristics occurring in massive multiple-input multipleoutput(MIMO) channels and the relaxation iteration(RI) method to avoid the matrix inversion. A proper initial solution is given to accelerate the convergence speed. In addition, we point out that the channel estimation scheme used in channel hardening-exploiting message passing(CHEMP) receiver is very appropriate for our proposed detection algorithm. Simulation results verify that the proposed algorithm can achieve very close performance of the traditional MMSE algorithm with a small number of iterations.
文摘With a low resolution 1-bit ADC on its receiver(RX) side, MIMO with 1-bit ADC took a considerable step in the fulfillment of the hardware complexity constrains of the internet of things(IoT) PHY layer design. However, applying 1-bit ADC at MIMO RX results in severe nonlinear quantization error. By which, almost all received signal amplitude information is completely distorted. Thus, MIMO channel estimation is considered as a major barrier towards practical realization of 1-bit ADC MIMO system. In this paper, two efficient sparsity-based channel estimation techniques are proposed for 1-bit ADC MIMO systems, namely the low complexity sparsity-based channel estimation(LCSCE), and the iterative adaptive sparsity channel estimation(IASCE). In these techniques, the sparsity of the 1-bit ADC MIMO channel is exploited to propose a new adaptive and iterative compressive sensing(CS) recovery algorithm to handle the 1-bit ADC quantization effect. The proposed algorithms are tested with the state-of-the-art 1-bit ADC MIMO constant envelope modulation(MIMO-CEM). The 1-bit ADC MIMO-CEM system is chosen as it fulfills both energy and hardware complexity constraints of the IoT PHY layer. Simulation results reveal the high effectiveness of the proposed algorithms in terms of spectral efficiency(SE) and computational complexity. The proposed LCSCE reduces the computational complexity of the 1-bit ADC MIMO-CEM channel estimation by 86%, while the IASCE reduces it by 96% compared to the recent techniques of MIMO-CEM channel estimation. Moreover, the proposed LCSCE and IASCE improve the spectrum efficiency by 76 % and 73 %, respectively, compared to the recent techniques.
文摘In this paper,the performance of uplink multiuser massive multiple-input multipleoutput(MIMO)system with spatial modulation over transmit-correlated Rayleigh fading channel is investigated,where a large number of antennas are deployed at the base station and linear zero-forcing(ZF)receiver is employed for detection.By taking the transmit correlation and the randomness of shadow fading in to account,the bit error rate(BER)performance of the system is analyzed.According to the performance analysis,an approximated expression of overall average BER of the system is attained.Besides,asymptotic performance is studied and the corresponding BER expression at high signal-to-noise ratio is derived.On this basis,the diversity gain of the system can be obtained for performance evaluation.Simulation results show that the derived theoretical expressions match the simulated values well,which verifies the correctness of our analysis.
基金support under the Multi-Disciplinary Research(MDR)Grant(H470)the Ministry of Higher Education Malaysia under the Fundamental Research Grant Scheme(FRGS/1/2019/TK04/UTHM/02/8).
文摘Energy efficiency(EE)is a critical design when taking into account circuit power consumption(CPC)in fifth-generation cellular networks.These problems arise because of the increasing number of antennas in massive multiple-input multiple-output(MIMO)systems,attributable to inter-cell interference for channel state information.Apart from that,a higher number of radio frequency(RF)chains at the base station and active users consume more power due to the processing activities in digital-to-analogue converters and power amplifiers.Therefore,antenna selection,user selection,optimal transmission power,and pilot reuse power are important aspects in improving energy efficiency in massive MIMO systems.This work aims to investigate joint antenna selection,optimal transmit power and joint user selection based on deriving the closed-form of the maximal EE,with complete knowledge of large-scale fading with maximum ratio transmission.It also accounts for channel estimation and eliminating pilot contamination as antennas M→∞.This formulates the optimization problem of joint optimal antenna selection,transmits power allocation and joint user selection to mitigate inter-cellinterference in downlink multi-cell massive MIMO systems under minimized reuse of pilot sequences based on a novel iterative low-complexity algorithm(LCA)for Newton’s methods and Lagrange multipliers.To analyze the precise power consumption,a novel power consumption scheme is proposed for each individual antenna,based on the transmit power amplifier and CPC.Simulation results demonstrate that the maximal EE was achieved using the iterative LCA based on reasonable maximum transmit power,in the case the noise power is less than the received power pilot.The maximum EE was achieved with the desired maximum transmit power threshold by minimizing pilot reuse,in the case the transmit power allocationρd=40 dBm,and the optimal EE=71.232 Mb/j.
