Hard ceramic coatings such as TiN and CrN are very successful and are widely used in improving the performance of cutting and forming tools, but they are less successful in providing protection for general machine com...Hard ceramic coatings such as TiN and CrN are very successful and are widely used in improving the performance of cutting and forming tools, but they are less successful in providing protection for general machine components, such as gears and engine parts. The development of low-friction wear resistant coatings that can run dry or in a minimum amount of oil is becoming increasingly important to this industry. Two recently developed carbon-based coatings Graphit-iC? and Dymon-iC, which are shown to exhibit very high sliding wear resistance and low friction in dry conditions, are compared to a CrN coating under oil lubricated conditions. Long term pin-on-disc tests using a chrome steel counterface ball were carried out on coated HSS test samples. All the coatings performed well at very high applied contact pressures, exceeding 1.5 GPa, but the Graphit-iC? and Dymon-iC coatings also exhibited the desirable characteristic of protecting the counterface material. Reasons for this behaviour are discussed.展开更多
Efficient lubrication of magnesium alloys is a highly challenging topic in the field of tribology.In this study,magnesium silicate hydroxide(MSH)nanotubes with serpentine structures were synthesized.The tribological b...Efficient lubrication of magnesium alloys is a highly challenging topic in the field of tribology.In this study,magnesium silicate hydroxide(MSH)nanotubes with serpentine structures were synthesized.The tribological behavior of AZ91D magnesium alloy rubbed against GCr15 steel was studied under lubricating oil with surface-modified MSH nanotubes as additives.The effects of the concentration,applied load,and reciprocating frequency on the friction and wear of the AZ91D alloy were studied using an SRV-4 sliding wear tester.Results show a decrease of 18.7–68.5%in friction coefficient,and a reduction of 19.4–54.3%in wear volume of magnesium alloy can be achieved by applying the synthetic serpentine additive under different conditions.A suspension containing 0.3 wt.%MSH was most efficient in reducing wear and friction.High frequency and medium load were more conducive to improving the tribological properties of magnesium alloys.A series of beneficial physical and chemical processes occurring at the AZ91D alloy/steel interface can be used to explain friction and wear reduction based on the characterization of the morphology,chemical composition,chemical state,microstructure,and nanomechanical properties of the worn surface.The synthetic MSH,with serpentine structure and nanotube morphology,possesses excellent adsorbability,high chemical activity,and good self-lubrication and catalytic activity.Therefore,physical polishing,tribochemical reactions,and physicalchemical depositions can occur easily on the sliding contacts.A dense tribolayer with a complex composition and composite structure was formed on the worn surface.Its high hardness,good toughness and plasticity,and prominent lubricity resulted in the improvement of friction and wear,making the synthetic MSH a promising efficient oil additive for magnesium alloys under boundary and mixed lubrication.展开更多
During high-speed rotation,the surface of aeronautic spiral bevel gears will generate significant pressure and viscous forces,which will cause a certain amount of windage power loss and reduce the efficiency of the tr...During high-speed rotation,the surface of aeronautic spiral bevel gears will generate significant pressure and viscous forces,which will cause a certain amount of windage power loss and reduce the efficiency of the transmission system.Based on the computational fluid dynamics,this paper analyzes the windage power loss of a single spiral bevel gear and a spiral bevel gear pair under oil injection lubrication.In addition,the shroud is used to suppress gear windage loss,and the clearance size and opening angle of the designed shroud are optimized.Finally,by comparing and analyzing the experimental results,the following conclusions were obtained:(1)For a single gear,the speed is the most important factor affecting windage loss,followed by the hand of spiral,and rotation direction;(2)For gear pairs,under oil injection lubrication,the input speed has the greatest impact on windage power loss,followed by the influence of oil injection port speed,temperature and oil injection port pressure;(3)Installing a shroud is an effective method to reduce windage power loss;(4)In the pure air phase,the smaller the clearance between the shroud and the gear surface,and the smaller the radial direction between the shroud and the shaft,the better the effect of reducing windage;(5)In the two-phase flow of oil and gas,it is necessary to design oil drainage holes on the shroud to ensure the smooth discharge of lubricating oil and improve the drag reduction effect.展开更多
With the rapid advancement of science and technology,along with an increasing global focus on space exploration,there is a growing concern for addressing friction and wear issues in surface coatings for components ope...With the rapid advancement of science and technology,along with an increasing global focus on space exploration,there is a growing concern for addressing friction and wear issues in surface coatings for components operating in high-temperature environments within the aerospace sector.However,typical high-temperature coatings currently face challenges in effectively integrating excellent oxidation resistance,wear resistance,and lubrication properties in high-temperature settings.Studies have demonstrated the significant potential of Transition Metal Dichalcogenides(TMDCs)as lubricant additives in high-temperature lubrication,attributable to their distinctive crystal structures.Thus,this review concentrates on the compositional design of individual MX_(2)-type(M=W,Mo,Nb,Ta;X=S,Se)TMDCs(molybdenum disulfide(MoS_(2)),tungsten disulfide(WS2),niobium diselenide(NbSe_(2)),molybdenum diselenide(MoSe_(2)),tungsten diselenide(WSe_(2)))and their composites,including inorganic oxygen-containing sulfides,and explores the utilization of TMDCs in self-lubricating coatings.Furthermore,conventional preparation methods(mechanical exfoliation,liquid-phase ultrasonic exfoliation,chemical vapour deposition)for synthesizing TMDCs are outlined.Finally,an analysis of the lubrication mechanism of MX_(2)-type TMDCs is provided,along with future directions for enhancing the high-temperature lubrication performance of composite coatings.展开更多
Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.Ho...Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.However,understanding the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance from a comprehensive perspective is crucial for guiding their future development.This review provides a timely and comprehensive overview of the applications of 2D nanomaterials in oil-based lubrication.First,the bottlenecks and mechanisms of action of 2D nanomaterials are outlined,including adsorption protective films,charge adsorption effects,tribochemical reaction films,interlayer slip,and synergistic effects.On this basis,the review summarizes recent structural regulation strategies for 2D nanomaterials,including doping engineering,surface modification,structural optimization,and interfacial mixing engineering.Then,the focus was on analyzing the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance.The effects of thickness,number of layers,sheet diameter,interlayer spacing,Moiré patterns,wettability,functional groups,concentration,as well as interfacial compatibility and dispersion behavior of 2D nanomaterials were systematically investigated in oil-based lubrication,with the intrinsic correlations resolved through computational simulations.Finally,the review offers a preliminary summary of the significant challenges and future directions for 2D nanomaterials in oil-based lubrication.This review aims to provide valuable insights and development strategies for the rational design of high-performance oil-based lubrication materials.展开更多
The fixed-setting face-milled curvilinear cylindrical gear features teeth that are arc-shaped along the longitudinal direction.Some researchers hypothesize that this arc-tooth may enhance the lubrication conditions of...The fixed-setting face-milled curvilinear cylindrical gear features teeth that are arc-shaped along the longitudinal direction.Some researchers hypothesize that this arc-tooth may enhance the lubrication conditions of the gear.This study focuses on this type of gear,employing both finite element analysis(FEA)and analytical methods to determine the input parameters required for elastohydrodynamic lubrication(EHL)analysis.The effects of assembly errors,tooth surface modifications,load,and face-milling cutter radius on the lubrication performance of these gears are systematically investigated.The finite element model(FEM)of the gear pair is utilized to calculate the coordinates of contact points on the tooth surface and the corresponding contact pressures at the tooth surface nodes throughout a meshing cycle.Subsequently,the normal load on specific gear teeth is determined using a gradient-based approach.Entrainment speed,slip-to-roll ratio,and effective radius near the contact points on the tooth surface are derived through analytical methods.The data obtained from FEA serve as input parameters for EHL simulations.The lubrication performance of the curvilinear cylindrical gear is evaluated through example studies.The findings indicate that using FEA to provide input parameters for EHL simulations can reveal the occurrence of edge contact phenomena during gear meshing,allowing for a more accurate representation of the gear’s lubrication conditions.The lubrication performance of the curvilinear cylindrical gear is shown to be independent of the face-milling cutter radius but is significantly influenced by the size of the contact pattern on the tooth surface.Curvilinear gears with larger contact patterns demonstrate superior lubrication performance.展开更多
The contact characteristics of the rough tooth surface during the meshing process are significantly affected by the lubrication state.The coupling effect of tooth surface roughness and lubrication on meshing character...The contact characteristics of the rough tooth surface during the meshing process are significantly affected by the lubrication state.The coupling effect of tooth surface roughness and lubrication on meshing characteristics of planetary gear is studied.An improved three-dimensional(3 D)anisotropic tooth surface roughness fractal model is proposed based on the experimental parameters.Considering asperity contact and elastohydrodynamic lubrication(EHL),the contact load and flexibility deformation of the tooth surface are derived,and the deformation compatibility equation of the 3 D loaded tooth contact analysis(3 D-LTCA)method is improved.The asperity of the tooth surface changes the system from EHL to mixed lubrication and reduces the stiffness of the oil film.Compared with the sun planet gear,the asperity has a greater effect on the meshing characteristics of the ring-planet gear.Compared with the proposed method,the comprehensive stiffness obtained by the traditional calculation method considering the lubrication effect is smaller,especially for the ring-planet gear.Compared with roughness,speed and viscosity,the meshing characteristics of planetary gears are most sensitive to torque.展开更多
Minimum quantity lubrication(MQL)is a technique that achieves effective lubrication and cooling of the cutting zone by using a minimal amount of cutting fluid.This results in a decrease in the cutting temperature,exte...Minimum quantity lubrication(MQL)is a technique that achieves effective lubrication and cooling of the cutting zone by using a minimal amount of cutting fluid.This results in a decrease in the cutting temperature,extending the cutting tool life and improving the surface quality of the workpiece.Optimizing the nozzle settings can enhance the cooling and lubrication performance of MQL,leading to increased processing efficiency and product quality.Nozzles with different shapes are fabricated,and different outlet diameters and wall thicknesses are set.The cutting process takes into account the impact of spindle speed and feed rate.An experimental study is conducted to investigate the atomization cone angle and particle size distribution of different nozzles.The circular nozzle is more conducive to the concentrated injection of an atomized liquid beam.The atomization cone angle is the largest when the nozzle outlet diameter is 1.2 mm.Enlarging the nozzle outlet diameter will increase the diameter of the atomized droplets.The atomization cone angle increases while the droplet diameter decreases with the increase of outlet wall thickness.Properly increasing the outlet wall thickness is beneficial to improving the atomization quality.The droplet diameter increases firstly and then decreases with the increase of spindle speed and feed rate.Increasing the MQL gas supply pressure and reducing the lubricating oil flow rate will improve the atomization quality of the nozzle.Studies on the influence of the MQL nozzle processing technology on the atomization effect can help to enhance the cooling and lubrication performance of the MQL technology,leading to improved processing efficiency and quality.展开更多
The friction and wear tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disk in a pin-on-disk tribometer system under PAO oil lubrication conditions. It was found that Nitinol 60 alloy can be lu...The friction and wear tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disk in a pin-on-disk tribometer system under PAO oil lubrication conditions. It was found that Nitinol 60 alloy can be lubricated well and has shown remarkable tribological performance. Average coefficient of friction （COF） of Nitinol 60 is 0.6 under dry friction; however, average COF decreases to 0.1 under PAO oil lubrication. SEM image of the worn surface shows that Nitinol 60 exhibits excellent wear resistance and the wear mechanism is mainly adhesive wear. Flow pattern of oil-air flow in oil pipe was simulated by FLUENT software with VOF model for acquiring working performance of oil-air lubrication. The optimum velocity of oil and air at the inlet was achieved, which provides the great proposal for the design of experiment of oil-air lubrication of Nitinol 60 alloy. The simulation results showed that the optimum annular flow of flow pattern was obtained when air velocity is 10 m/s and oil velocity is 0.05 m/s. The formation mechanism of annular flow was also discussed in the present study.展开更多
To better understand and know the roles of cooling/lubrication medium in the cutting process and expand their applicability,uncoated cemented carbide tools are used in high-speed turning Ti6Al4V.Dry,cold air,minimal q...To better understand and know the roles of cooling/lubrication medium in the cutting process and expand their applicability,uncoated cemented carbide tools are used in high-speed turning Ti6Al4V.Dry,cold air,minimal quantity lubrication（MQL）,cryogenic MQL,and ionized air as the cooling/lubrication conditions are studied.Experimental results show that at speed 120 m/min turning Ti6Al4V,the cutting force under ionized air is smallest under all lubricant conditions,and tool life is best,next is cryogenic MQL.MQL and cold air almost have the same effect,a little better than dry.Meanwhile the smallest surface roughness is also obtained under ionized air condition.Flank wear and crater wear are the dominant failure modes when high-speed turning Ti6Al4V by SEM analysis.Finally the conclusion is drawn that ionized air and cryogenic MQL have better cooling/lubrication effects and can effectively improve the tool life.展开更多
The tribological tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disc in the tribometer system. Four kinds of oils were experimentally investigated as lubrication oils for lubricating Nitinol ...The tribological tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disc in the tribometer system. Four kinds of oils were experimentally investigated as lubrication oils for lubricating Nitinol 60 alloy in the boundary lubrication regime. The experimental results were compared with a reference dry friction. It was found that Nitinol 60 alloy can be lubricated significantly and has shown remarkable lubrication performance. A superlubricity behavior of Nitinol 60 alloy was observed under castor oil lubrication. An ultra-low coefficient of friction of Nitinol 60 alloy about 0.008 between Nitinol 60 alloy and GCr15 steel was obtained under castor oil lubrication condition after a running-in period. Accordingly, the present study is focused on the lubrication behaviors of castor oil as potential lubrication oil for Nitinol 60 alloy. In the presence of castor oil, coefficient of friction is kept at 0.008 at steady state, corresponding to so-called superlubricity regime （when sliding is then approaching pure rolling）. The mechanism of superlubricity is attributed to the triboformed OH-terminated surfaces from friction-induced dissociation of castor oil and the boundary lubrication films formed on the contact surface due to high polarity and long chain of castor oil allowing strong interactions with the lubricated surfaces.展开更多
The finite element method （FEM） is introduced to calculate the oil film pressure and temperature distribution of a journal bearing. The perturbation is performed directly on the finite element equation. Consequently...The finite element method （FEM） is introduced to calculate the oil film pressure and temperature distribution of a journal bearing. The perturbation is performed directly on the finite element equation. Consequently, the Jacobian matrices of the oil film forces are concisely obtained. The equilibrium position of the bearing with a given static load is found by the Newton-Raphson method. As byproducts, dynamic coefficients are obtained simultaneously without any extra computing time. From the numerical results, it is concluded that the effects of film temperature on stiffness coefficients are bigger than those on damping coefficients. With the increase of rotational speed, the load capacity and the stiffness coefficients of the journal bearing are increased when the eccentricity is small, while decreased when the eccentricity is big.展开更多
Friction and lubrication simulation analysis of internal combustion engine bearings are studied. A series of software implementary precepts for mathematical modeling, to analytic calculating and realizing simulation o...Friction and lubrication simulation analysis of internal combustion engine bearings are studied. A series of software implementary precepts for mathematical modeling, to analytic calculating and realizing simulation outcome are brought forward. As a dynamic simulating technique is introduced into the process of engine bearing design, simulation models of the oil film are built and the emulational analysis of the shaft center track is carried out. A software program package “Engine Bearing Friction and Lubrication Dynamic Simulation System” is developed to realize the real time simulation of the working status of bearing during the design process. Through developing virtualized products, the defects of the product design can be found in time and improve the products at once. Thus the purpose of predicting and controlling the cost, quality and design period of the products can be achieved.展开更多
In order to more accurately predict the contact fatigue life of rolling bearing, a prediction method of fatigue life of rolling bearing is proposed based on elastohydrodynamic lubrication （EHL）, the 3-paameter Weibu...In order to more accurately predict the contact fatigue life of rolling bearing, a prediction method of fatigue life of rolling bearing is proposed based on elastohydrodynamic lubrication （EHL）, the 3-paameter Weibull distribution ad fatigue strength. First,the contact stress considering elliptical EHL is obtained by mapping film pressure onto the Hertz zone. Then,the basic strength model of rolling bearing based on the 3-parameter Weibull distribution is deduced by the series connection reliability theory. Considering the effect of the type of stress, variation of shape and fuctuation of load, the mathematical models of the 尸 -tS-TV curve of the minimum life and the characteristic life for rolling bearing are established, respectively, and thus the prediction model of fatigue life of rolling bearing based on the 3-paameter Weibull distribution and fatigue strength is further deduced. Finally, the contact fatigue life obtained by the proposed method ad the latest international standard （IS0281： 2007） about the fatigue life prediction of rolling bearing are compared with those obtained by the statistical method. Results show that the proposed prediction method is effective and its relative error is smaier than that of the latest international standard （IS0281： 2007） with reliability R 〉 0. 93.展开更多
The dynamic contact behavior of worn bearings with elastoplastic functionally graded coating is studied,and the interacting effect between worn band and functionally graded surface is analyzed.The surface deformation ...The dynamic contact behavior of worn bearings with elastoplastic functionally graded coating is studied,and the interacting effect between worn band and functionally graded surface is analyzed.The surface deformation and roughness are included in the film thickness.The mixed elastohydrodynamic lubrication combined with point contact model is introduced to analyze the oil pressure in the contact zone.By using the Fourier transform method and Papkovich-Neuber potential function,the displacements and stress fields in the elastoplastic functionally graded coating are obtained.The second-order central difference method is used to solve the Reynolds equation.It is found that the repeated surface interaction can result in the sharp increase in pressure in bearings,and the oil pressure increases with increasing graded index.The entrainment of oil in the inlet and outlet zones becomes more evident if a large graded index is selected.展开更多
文摘Hard ceramic coatings such as TiN and CrN are very successful and are widely used in improving the performance of cutting and forming tools, but they are less successful in providing protection for general machine components, such as gears and engine parts. The development of low-friction wear resistant coatings that can run dry or in a minimum amount of oil is becoming increasingly important to this industry. Two recently developed carbon-based coatings Graphit-iC? and Dymon-iC, which are shown to exhibit very high sliding wear resistance and low friction in dry conditions, are compared to a CrN coating under oil lubricated conditions. Long term pin-on-disc tests using a chrome steel counterface ball were carried out on coated HSS test samples. All the coatings performed well at very high applied contact pressures, exceeding 1.5 GPa, but the Graphit-iC? and Dymon-iC coatings also exhibited the desirable characteristic of protecting the counterface material. Reasons for this behaviour are discussed.
基金support from the National Natural Science Foundation of China(grant number 52075544)Innovation Funds of Jihua Laboratory(X220971UZ230)+1 种基金Basic and Applied Basic Research Foundation of Guangdong Province(2022A1515110649)Funds from Research Platforms of Guangdong Higher Education Institutes(2022ZDJS038).
文摘Efficient lubrication of magnesium alloys is a highly challenging topic in the field of tribology.In this study,magnesium silicate hydroxide(MSH)nanotubes with serpentine structures were synthesized.The tribological behavior of AZ91D magnesium alloy rubbed against GCr15 steel was studied under lubricating oil with surface-modified MSH nanotubes as additives.The effects of the concentration,applied load,and reciprocating frequency on the friction and wear of the AZ91D alloy were studied using an SRV-4 sliding wear tester.Results show a decrease of 18.7–68.5%in friction coefficient,and a reduction of 19.4–54.3%in wear volume of magnesium alloy can be achieved by applying the synthetic serpentine additive under different conditions.A suspension containing 0.3 wt.%MSH was most efficient in reducing wear and friction.High frequency and medium load were more conducive to improving the tribological properties of magnesium alloys.A series of beneficial physical and chemical processes occurring at the AZ91D alloy/steel interface can be used to explain friction and wear reduction based on the characterization of the morphology,chemical composition,chemical state,microstructure,and nanomechanical properties of the worn surface.The synthetic MSH,with serpentine structure and nanotube morphology,possesses excellent adsorbability,high chemical activity,and good self-lubrication and catalytic activity.Therefore,physical polishing,tribochemical reactions,and physicalchemical depositions can occur easily on the sliding contacts.A dense tribolayer with a complex composition and composite structure was formed on the worn surface.Its high hardness,good toughness and plasticity,and prominent lubricity resulted in the improvement of friction and wear,making the synthetic MSH a promising efficient oil additive for magnesium alloys under boundary and mixed lubrication.
基金Supported by National Natural Science Foundation of China(Grant Nos.51175422,61973011)Shaanxi Provincial Natural Science Basic Research Plan of China(Grant No.2022JM-195)+1 种基金Fundamental Research Funds for the Central Universities of Chinathe Research Start-up Funds of Hangzhou International Innovation Institute of Beihang University(Grant No.2024KQ036)。
文摘During high-speed rotation,the surface of aeronautic spiral bevel gears will generate significant pressure and viscous forces,which will cause a certain amount of windage power loss and reduce the efficiency of the transmission system.Based on the computational fluid dynamics,this paper analyzes the windage power loss of a single spiral bevel gear and a spiral bevel gear pair under oil injection lubrication.In addition,the shroud is used to suppress gear windage loss,and the clearance size and opening angle of the designed shroud are optimized.Finally,by comparing and analyzing the experimental results,the following conclusions were obtained:(1)For a single gear,the speed is the most important factor affecting windage loss,followed by the hand of spiral,and rotation direction;(2)For gear pairs,under oil injection lubrication,the input speed has the greatest impact on windage power loss,followed by the influence of oil injection port speed,temperature and oil injection port pressure;(3)Installing a shroud is an effective method to reduce windage power loss;(4)In the pure air phase,the smaller the clearance between the shroud and the gear surface,and the smaller the radial direction between the shroud and the shaft,the better the effect of reducing windage;(5)In the two-phase flow of oil and gas,it is necessary to design oil drainage holes on the shroud to ensure the smooth discharge of lubricating oil and improve the drag reduction effect.
文摘With the rapid advancement of science and technology,along with an increasing global focus on space exploration,there is a growing concern for addressing friction and wear issues in surface coatings for components operating in high-temperature environments within the aerospace sector.However,typical high-temperature coatings currently face challenges in effectively integrating excellent oxidation resistance,wear resistance,and lubrication properties in high-temperature settings.Studies have demonstrated the significant potential of Transition Metal Dichalcogenides(TMDCs)as lubricant additives in high-temperature lubrication,attributable to their distinctive crystal structures.Thus,this review concentrates on the compositional design of individual MX_(2)-type(M=W,Mo,Nb,Ta;X=S,Se)TMDCs(molybdenum disulfide(MoS_(2)),tungsten disulfide(WS2),niobium diselenide(NbSe_(2)),molybdenum diselenide(MoSe_(2)),tungsten diselenide(WSe_(2)))and their composites,including inorganic oxygen-containing sulfides,and explores the utilization of TMDCs in self-lubricating coatings.Furthermore,conventional preparation methods(mechanical exfoliation,liquid-phase ultrasonic exfoliation,chemical vapour deposition)for synthesizing TMDCs are outlined.Finally,an analysis of the lubrication mechanism of MX_(2)-type TMDCs is provided,along with future directions for enhancing the high-temperature lubrication performance of composite coatings.
基金supported by the National Natural Science Foundation of China(No.51874036)the Natural Science Foundation of Ningxia(No.2024AAC02034)。
文摘Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.However,understanding the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance from a comprehensive perspective is crucial for guiding their future development.This review provides a timely and comprehensive overview of the applications of 2D nanomaterials in oil-based lubrication.First,the bottlenecks and mechanisms of action of 2D nanomaterials are outlined,including adsorption protective films,charge adsorption effects,tribochemical reaction films,interlayer slip,and synergistic effects.On this basis,the review summarizes recent structural regulation strategies for 2D nanomaterials,including doping engineering,surface modification,structural optimization,and interfacial mixing engineering.Then,the focus was on analyzing the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance.The effects of thickness,number of layers,sheet diameter,interlayer spacing,Moiré patterns,wettability,functional groups,concentration,as well as interfacial compatibility and dispersion behavior of 2D nanomaterials were systematically investigated in oil-based lubrication,with the intrinsic correlations resolved through computational simulations.Finally,the review offers a preliminary summary of the significant challenges and future directions for 2D nanomaterials in oil-based lubrication.This review aims to provide valuable insights and development strategies for the rational design of high-performance oil-based lubrication materials.
基金funded by the Sichuan Science and Technology Program(Project Nos.2024NSFSC0140,2023NSFSC0414,2022NSFSC0454)Panzhihua City Provincial Targeted Financial Resources Transfer Payment(Grant No.222Y2F-GG-04)+4 种基金Open Project of the Key Laboratory of Process Equipment and Control in Sichuan Province(ProjectNo.GK202211)Cultivation Research Project of PanzhihuaUniversity(ProjectNo.2023PY11)Open Project of Sichuan Provincial Engineering Technology Research Center for Advanced Manufacturing of Titanium Alloys(Project No.TM-2023-Z-02)Open Project of Panzhihua Key Laboratory of Advanced Manufacturing Technology(Project No.2022XJZD05).
文摘The fixed-setting face-milled curvilinear cylindrical gear features teeth that are arc-shaped along the longitudinal direction.Some researchers hypothesize that this arc-tooth may enhance the lubrication conditions of the gear.This study focuses on this type of gear,employing both finite element analysis(FEA)and analytical methods to determine the input parameters required for elastohydrodynamic lubrication(EHL)analysis.The effects of assembly errors,tooth surface modifications,load,and face-milling cutter radius on the lubrication performance of these gears are systematically investigated.The finite element model(FEM)of the gear pair is utilized to calculate the coordinates of contact points on the tooth surface and the corresponding contact pressures at the tooth surface nodes throughout a meshing cycle.Subsequently,the normal load on specific gear teeth is determined using a gradient-based approach.Entrainment speed,slip-to-roll ratio,and effective radius near the contact points on the tooth surface are derived through analytical methods.The data obtained from FEA serve as input parameters for EHL simulations.The lubrication performance of the curvilinear cylindrical gear is evaluated through example studies.The findings indicate that using FEA to provide input parameters for EHL simulations can reveal the occurrence of edge contact phenomena during gear meshing,allowing for a more accurate representation of the gear’s lubrication conditions.The lubrication performance of the curvilinear cylindrical gear is shown to be independent of the face-milling cutter radius but is significantly influenced by the size of the contact pattern on the tooth surface.Curvilinear gears with larger contact patterns demonstrate superior lubrication performance.
基金Project(2024A1515240020)supported by the Guangdong Basic and Applied Basic Research Foundation,China。
文摘The contact characteristics of the rough tooth surface during the meshing process are significantly affected by the lubrication state.The coupling effect of tooth surface roughness and lubrication on meshing characteristics of planetary gear is studied.An improved three-dimensional(3 D)anisotropic tooth surface roughness fractal model is proposed based on the experimental parameters.Considering asperity contact and elastohydrodynamic lubrication(EHL),the contact load and flexibility deformation of the tooth surface are derived,and the deformation compatibility equation of the 3 D loaded tooth contact analysis(3 D-LTCA)method is improved.The asperity of the tooth surface changes the system from EHL to mixed lubrication and reduces the stiffness of the oil film.Compared with the sun planet gear,the asperity has a greater effect on the meshing characteristics of the ring-planet gear.Compared with the proposed method,the comprehensive stiffness obtained by the traditional calculation method considering the lubrication effect is smaller,especially for the ring-planet gear.Compared with roughness,speed and viscosity,the meshing characteristics of planetary gears are most sensitive to torque.
文摘Minimum quantity lubrication(MQL)is a technique that achieves effective lubrication and cooling of the cutting zone by using a minimal amount of cutting fluid.This results in a decrease in the cutting temperature,extending the cutting tool life and improving the surface quality of the workpiece.Optimizing the nozzle settings can enhance the cooling and lubrication performance of MQL,leading to increased processing efficiency and product quality.Nozzles with different shapes are fabricated,and different outlet diameters and wall thicknesses are set.The cutting process takes into account the impact of spindle speed and feed rate.An experimental study is conducted to investigate the atomization cone angle and particle size distribution of different nozzles.The circular nozzle is more conducive to the concentrated injection of an atomized liquid beam.The atomization cone angle is the largest when the nozzle outlet diameter is 1.2 mm.Enlarging the nozzle outlet diameter will increase the diameter of the atomized droplets.The atomization cone angle increases while the droplet diameter decreases with the increase of outlet wall thickness.Properly increasing the outlet wall thickness is beneficial to improving the atomization quality.The droplet diameter increases firstly and then decreases with the increase of spindle speed and feed rate.Increasing the MQL gas supply pressure and reducing the lubricating oil flow rate will improve the atomization quality of the nozzle.Studies on the influence of the MQL nozzle processing technology on the atomization effect can help to enhance the cooling and lubrication performance of the MQL technology,leading to improved processing efficiency and quality.
基金Project (2012M511993) supported by China Postdoctoral Science FoundationProject (TPL1202) supported by the Open Fund Program of the State Key Laboratory of Traction Power, Southwest Jiaotong University, China
文摘The friction and wear tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disk in a pin-on-disk tribometer system under PAO oil lubrication conditions. It was found that Nitinol 60 alloy can be lubricated well and has shown remarkable tribological performance. Average coefficient of friction （COF） of Nitinol 60 is 0.6 under dry friction; however, average COF decreases to 0.1 under PAO oil lubrication. SEM image of the worn surface shows that Nitinol 60 exhibits excellent wear resistance and the wear mechanism is mainly adhesive wear. Flow pattern of oil-air flow in oil pipe was simulated by FLUENT software with VOF model for acquiring working performance of oil-air lubrication. The optimum velocity of oil and air at the inlet was achieved, which provides the great proposal for the design of experiment of oil-air lubrication of Nitinol 60 alloy. The simulation results showed that the optimum annular flow of flow pattern was obtained when air velocity is 10 m/s and oil velocity is 0.05 m/s. The formation mechanism of annular flow was also discussed in the present study.
基金Supported by the National Natural Science Foundation of China(50975141,51005118)~~
文摘To better understand and know the roles of cooling/lubrication medium in the cutting process and expand their applicability,uncoated cemented carbide tools are used in high-speed turning Ti6Al4V.Dry,cold air,minimal quantity lubrication（MQL）,cryogenic MQL,and ionized air as the cooling/lubrication conditions are studied.Experimental results show that at speed 120 m/min turning Ti6Al4V,the cutting force under ionized air is smallest under all lubricant conditions,and tool life is best,next is cryogenic MQL.MQL and cold air almost have the same effect,a little better than dry.Meanwhile the smallest surface roughness is also obtained under ionized air condition.Flank wear and crater wear are the dominant failure modes when high-speed turning Ti6Al4V by SEM analysis.Finally the conclusion is drawn that ionized air and cryogenic MQL have better cooling/lubrication effects and can effectively improve the tool life.
基金Project(51305331)supported by the National Natural Science Foundation of ChinaProject(2012M511993)supported by China Postdoctoral Science FoundationProject(TPL1202)supported by the Open Fund Program of the State Key Laboratory of Traction Power,Southwest Jiaotong University,China
文摘The tribological tests were performed using Nitinol 60 alloy pin sliding over GCr15 steel disc in the tribometer system. Four kinds of oils were experimentally investigated as lubrication oils for lubricating Nitinol 60 alloy in the boundary lubrication regime. The experimental results were compared with a reference dry friction. It was found that Nitinol 60 alloy can be lubricated significantly and has shown remarkable lubrication performance. A superlubricity behavior of Nitinol 60 alloy was observed under castor oil lubrication. An ultra-low coefficient of friction of Nitinol 60 alloy about 0.008 between Nitinol 60 alloy and GCr15 steel was obtained under castor oil lubrication condition after a running-in period. Accordingly, the present study is focused on the lubrication behaviors of castor oil as potential lubrication oil for Nitinol 60 alloy. In the presence of castor oil, coefficient of friction is kept at 0.008 at steady state, corresponding to so-called superlubricity regime （when sliding is then approaching pure rolling）. The mechanism of superlubricity is attributed to the triboformed OH-terminated surfaces from friction-induced dissociation of castor oil and the boundary lubrication films formed on the contact surface due to high polarity and long chain of castor oil allowing strong interactions with the lubricated surfaces.
基金Supported by the National″111″Project(B07050)the China Postdoctoral Science Foundation(20100471634)~~
文摘The finite element method （FEM） is introduced to calculate the oil film pressure and temperature distribution of a journal bearing. The perturbation is performed directly on the finite element equation. Consequently, the Jacobian matrices of the oil film forces are concisely obtained. The equilibrium position of the bearing with a given static load is found by the Newton-Raphson method. As byproducts, dynamic coefficients are obtained simultaneously without any extra computing time. From the numerical results, it is concluded that the effects of film temperature on stiffness coefficients are bigger than those on damping coefficients. With the increase of rotational speed, the load capacity and the stiffness coefficients of the journal bearing are increased when the eccentricity is small, while decreased when the eccentricity is big.
文摘Friction and lubrication simulation analysis of internal combustion engine bearings are studied. A series of software implementary precepts for mathematical modeling, to analytic calculating and realizing simulation outcome are brought forward. As a dynamic simulating technique is introduced into the process of engine bearing design, simulation models of the oil film are built and the emulational analysis of the shaft center track is carried out. A software program package “Engine Bearing Friction and Lubrication Dynamic Simulation System” is developed to realize the real time simulation of the working status of bearing during the design process. Through developing virtualized products, the defects of the product design can be found in time and improve the products at once. Thus the purpose of predicting and controlling the cost, quality and design period of the products can be achieved.
基金The National Defense Advance Research Program(No.81302XXX)
文摘In order to more accurately predict the contact fatigue life of rolling bearing, a prediction method of fatigue life of rolling bearing is proposed based on elastohydrodynamic lubrication （EHL）, the 3-paameter Weibull distribution ad fatigue strength. First,the contact stress considering elliptical EHL is obtained by mapping film pressure onto the Hertz zone. Then,the basic strength model of rolling bearing based on the 3-parameter Weibull distribution is deduced by the series connection reliability theory. Considering the effect of the type of stress, variation of shape and fuctuation of load, the mathematical models of the 尸 -tS-TV curve of the minimum life and the characteristic life for rolling bearing are established, respectively, and thus the prediction model of fatigue life of rolling bearing based on the 3-paameter Weibull distribution and fatigue strength is further deduced. Finally, the contact fatigue life obtained by the proposed method ad the latest international standard （IS0281： 2007） about the fatigue life prediction of rolling bearing are compared with those obtained by the statistical method. Results show that the proposed prediction method is effective and its relative error is smaier than that of the latest international standard （IS0281： 2007） with reliability R 〉 0. 93.
基金This work is supported by the National Natural Science Foundations of China(No.11790282)National Natural Science Foundations of Hebei,China(A2019210037).
文摘The dynamic contact behavior of worn bearings with elastoplastic functionally graded coating is studied,and the interacting effect between worn band and functionally graded surface is analyzed.The surface deformation and roughness are included in the film thickness.The mixed elastohydrodynamic lubrication combined with point contact model is introduced to analyze the oil pressure in the contact zone.By using the Fourier transform method and Papkovich-Neuber potential function,the displacements and stress fields in the elastoplastic functionally graded coating are obtained.The second-order central difference method is used to solve the Reynolds equation.It is found that the repeated surface interaction can result in the sharp increase in pressure in bearings,and the oil pressure increases with increasing graded index.The entrainment of oil in the inlet and outlet zones becomes more evident if a large graded index is selected.
