Conventional locking/release mechanisms often face challenges in aircraft wing separation processes,such as excessive impact loads and insufficient synchronization.These may cause structural damage to the airframe or ...Conventional locking/release mechanisms often face challenges in aircraft wing separation processes,such as excessive impact loads and insufficient synchronization.These may cause structural damage to the airframe or attitude instability,seriously compromising mission reliability.To address this engineering challenge,this paper proposes a multi-point low-impact locking/release mechanism based on the mobility model and energy conversion strategy.Through establishing a DOF constraint framework system,this paper systematically analyzes the energy transfer and conversion characteristics during the wing separation process,reveals the generation mechanism of impact loads,and conducts research on low-impact design based on energy conversion strategy.Building on this foundation,a single-point locking/release mechanism employing parallel trapezoidal key shaft structure was designed,which increases frictional contact time and reduces the energy release rate,thereby achieving low-impact characteristics.The mechanism's performance was validated through physical prototype development and systematic functional testing(including unlocking force,synchronization,and impact tests).Experimental results demonstrate:(1)Under 14 kN preload condition,the maximum unlocking force was only 92.54 N,showing a linear relationship with preload that satisfies the"strong-connection/weak-unlock"design requirement;(2)Wing separation was completed within 46 ms,with synchronization time difference among three separation mechanisms stably controlled within 12-14 ms,proving rapid and reliable operation;(3)The unlocking impact acceleration ranged between 26 and 73 g,below the 100 g design limit,confirming the effectiveness of the energy conversion strategy.The proposed low-impact locking/release mechanism design method based on energy conversion strategy resolves the traditional challenges of high impact and synchronization deficiencies.The synergistic optimization mechanism of"structural load reduction and performance improvement"provides a highly reliable technical solution for wing separable mechanisms while offering novel design insights for wing connection/separation systems engineering.展开更多
Cascading thermal runaway(TR)propagation poses a critical safety concern for large-format sodium-ion battery(SIB)systems because of the heightened risks of fires or explosions.However,effectively suppressing TR propag...Cascading thermal runaway(TR)propagation poses a critical safety concern for large-format sodium-ion battery(SIB)systems because of the heightened risks of fires or explosions.However,effectively suppressing TR propagation without introducing unintended side effects remains a significant challenge.Herein,we demonstrate a localized energy release method to mitigate TR,by reducing the state of charge(SOC)of cells adjacent to the thermally runaway unit.We discover that as the SOCs decreased from 100%to 25%,the TR trigger temperature decreased significantly,and the maximum temperature decrease from 367 to 229℃.Meanwhile,the volume of gas decreased to one-third of its original value,while the range of explosion limits significantly narrowed.The analysis of the morphology of the debris further confirms that the structural damage is greater at higher SOC levels.Moreover,an Entropy Weight and Technique for Order Preference by Similarity to an Ideal Solution(EW-TOPSIS)method has been established to assess the safety status of SIBs,showing that the TR possibility is nearly linear with the SOCs,and the TR hazard is exponentially related to the SOCs.Finally,when the SOC of cells adjacent to the TR cell is reduced to 25%,TR can be directly blocked without the need for additional cooling or thermal insulation methods.This study not only advances the understanding of TR behavior in SIBs but also offers a straightforward approach to mitigating the TR risk in SIB systems.展开更多
To assess the merits of PEGylated poly （lactic-co-glycolic acid） （PEG-PLGA） nanoparticles as drug carriers for tumor necrosis factor-α receptor blocking peptide （TNFR-BP）, PEG-PLGA copolymer, which could be use...To assess the merits of PEGylated poly （lactic-co-glycolic acid） （PEG-PLGA） nanoparticles as drug carriers for tumor necrosis factor-α receptor blocking peptide （TNFR-BP）, PEG-PLGA copolymer, which could be used to prepare the stealth nanoparticles, was synthesized with methoxypolyethyleneglycol, DL-lactide and glycolide. The structure of PEG-PLGA was confirmed with ^1H-NMR and FT-IR spectroscopy, and the molecular weight （MW） was determined by gel permeation chromatography. Fluorescent FITC-TNFR- BP was chosen as model protein and encapsulated within PEG-PLGA nanoparticles using the double emulsion method. Atomic force microscopy and photon correlation spectroscopy were employed to characterize the stealth nanoparticles fabricated for morphology, size with polydispersity index and zeta potential. Encapsulation efficiency （EE） and the release of FITC-TNFR-BP in nanopartieles in vitro were measured by the fluorescence measurement. The stealth nanoparticles were found to have the mean diameter less than 270 nm and zeta potential less than -20 mV. In all nanoparticle formulations, more than 45% of EE were obtained. FITC-TNFR-BP release from the PEG-PLGA nanoparticles exhibited a biphasic pattern, initial burst release and consequently sustained release. The experimental results show that PEG-PLGA nanoparticles possess the potential to develop as drug carriers for controlled release applications of TNFR-BP.展开更多
The electrochemical corrosion of ductile pipes(DPs)in drinking water distribution systems(DWDS)has a crucial impact on cement-mortar lining(CML)failure and metal release,potentially leading to drinking water quality d...The electrochemical corrosion of ductile pipes(DPs)in drinking water distribution systems(DWDS)has a crucial impact on cement-mortar lining(CML)failure and metal release,potentially leading to drinking water quality deterioration and posing a risk to public health.An in-situ scanning vibrating electrode technique(SVET)with micron-scale resolution,microscopic scale detection and water quality analysis were used to investigate the corrosion behavior and metal release from DPs throughout the whole CML failure process.Metal pollutants release occurred at three different stages of CML failure process,and there are potential risks of water quality deterioration exceeding the maximum allowable levels set by national standards in the partial failure stage and lining peeling stage.Furthermore,the effects of water chemistry(Cl^(−),SO_(4)^(2−),NO_(3)−,and Ca^(2+))on corrosion scale growth and iron release activity,were investigated during the CML partial failure stage.Results showed that the CML failure process in DPs was accelerated by the autocatalysis of localized corrosion.Cl^(−)was found to damage the uncorroded metal surface,while SO_(4)^(2−)mainly dissolved the corrosion scale surface,increasing iron release.Both the oxidation of NO_(3)−and selective sedimentation of Ca2+were found to enhance the stability of corrosion scales and inhibit iron release.展开更多
Phase Change Material(PCM)-based cold energy storage system(CESS)can effectively utilize the peak and valley power resources to reduce the excessive dependence on the power grid.In this study,a PCM-based CESS was desi...Phase Change Material(PCM)-based cold energy storage system(CESS)can effectively utilize the peak and valley power resources to reduce the excessive dependence on the power grid.In this study,a PCM-based CESS was designed for cold storage applications.The optimal number of PCM plates was determined through numerical simulations to meet the required cold storage temperature and control time.Additionally,the air temperature field,flow field,and melting characteristics of the PCMplates during the cooling release process were analyzed.The effects of plate positioning and thickness on the cooling release performance were further investigated.The results indicated that when 64PCMplateswere used,the duration formaintaining temperatures below−18℃increased from0.6 h to approximately 16.94 h.During the cooling release process,the temperature field in the cold storage exhibited stratification,and the melting of the PCM plates was non-uniform.Placing the PCM plates at the top or within the interlayers without cargo above proved more effective,with their cooling release power being approximately twice that of the PCM plates placed in the interlayers with cargo above.Furthermore,reducing the thickness of the PCMplates from15 to 7.5mmresulted in a 3.6-h increase in the time below−18℃and a 4.5-h reduction in the time required to reach 80%liquid phase fraction.展开更多
Naturally degradable capsule provides a platform for sustained fragrance release.However,practical challenges such as low encapsulation efficiency and difficulty in sustained release are still limited in using fragran...Naturally degradable capsule provides a platform for sustained fragrance release.However,practical challenges such as low encapsulation efficiency and difficulty in sustained release are still limited in using fragranceloaded capsules.In this work,the natural materials sodium alginate and gelatine are dissolved and act as the aqueous phase,lavender is dissolved in caprylic/capric triglyceride(GTCC)as the oil phase,and SiO_(2) nanoparticles with neutralwettability as a solid emulsifier to form O/W Pickering emulsions simultaneously.Finally,multi-core capsules are prepared using the drop injection method with emulsions as templates.The results show that the capsules have been successfully prepared with a spherical morphology and multi-core structure,and the encapsulation rate of multi-core capsules can reach up to 99.6%.In addition,the multi-core capsules possess desirable sustained release performance,the cumulative sustained release rate of fragrance at 25℃over 49 days is only 32.5%.It is attributed to the significant protection of multi-core structure,Pickering emulsion nanoparticle membranes,and hydrogel network shell for encapsulated fragrance.This study is designed to deliver a new strategy for using sustained-release technology with fragrance in food,cosmetics,textiles,and other fields.展开更多
BACKGROUND In recent years,immune checkpoint inhibitors(ICIs)have demonstrated remarkable efficacy across diverse malignancies.Notably,in patients with advanced gastric cancer,the use of programmed death 1(PD-1)blocka...BACKGROUND In recent years,immune checkpoint inhibitors(ICIs)have demonstrated remarkable efficacy across diverse malignancies.Notably,in patients with advanced gastric cancer,the use of programmed death 1(PD-1)blockade has significantly prolonged overall survival,marking a pivotal advancement comparable to the impact of Herceptin over the past two decades.While the therapeutic benefits of ICIs are evident,the increasing use of immunotherapy has led to an increase in immune-related adverse events.CASE SUMMARY This article presents the case of a patient with advanced gastric cancer and chronic plaque psoriasis.Following sintilimab therapy,the patient developed severe rashes accompanied by cytokine release syndrome(CRS).Fortunately,effective management was achieved through the administration of glucocorticoid,tocilizumab,and acitretin,which resulted in favorable outcomes.CONCLUSION Glucocorticoid and tocilizumab therapy was effective in managing CRS after PD-1 blockade therapy for gastric cancer in a patient with chronic plaque psoriasis.展开更多
Pearl millet, Pennisetum glaucum (Leeke) R. Br, is the main cereal crop in Niger. This crop is seriously attacked by the millet Head miner (MHM), Heliocheilus albipunctella (de Joannis) (Lepidoptera, Noctuidae) causin...Pearl millet, Pennisetum glaucum (Leeke) R. Br, is the main cereal crop in Niger. This crop is seriously attacked by the millet Head miner (MHM), Heliocheilus albipunctella (de Joannis) (Lepidoptera, Noctuidae) causing significant yield losses. This study to optimize biological control of this pest was carried out in Niger in the laboratory and in a farming environment. In the laboratory, the larval paralysis and emergence of the parasitoid Habrobracon hebetor Say (Hymenoptera: Braconidae) were compared between release jute bags, plastic boxes and cardboard boxes. In a farming environment, direct releases were carried out with plastic boxes and releases with jute bags in 12 villages of the Maradi region during the cropping seasons of 2021 and 2022. The results indicated that 25 larvae of Corcyra cephalonica Stainton (Lepidoptera: Pyralidae) in the boxes were all paralyzed by 2 females of H. hebetor within 7 hours 30 minutes. The emergence of adults began on the 7th day after the beginning of the experiment for a period of two weeks and three weeks respectively in the boxes and jute bags. The production varied from 107.08 to 110.17 parasitoids and was comparable between the Jute bags, plastic boxes and cardboard boxes. In Farmers’ fields, the parasitoid release with the two methods caused the parasitism rates that varied from 64.32 to 66.52% depending on the year but in 2022 the rate of parasitism was higher in the fields with direct releases using plastic boxes (72.66%) compared to those released with jute bags (56.35%). Plastic boxes and cardboard boxes can be used for the production of the H. hebetor parasitoids. These results can be recommended to the cottage industries in the Sahel in order to improve the production and release methods of H. hebetor and make them more adapted to farmers’ fields.展开更多
Vascular endothelial growth factor and its mimic peptide KLTWQELYQLKYKGI(QK)are widely used as the most potent angiogenic factors for the treatment of multiple ischemic diseases.However,conventional topical drug deliv...Vascular endothelial growth factor and its mimic peptide KLTWQELYQLKYKGI(QK)are widely used as the most potent angiogenic factors for the treatment of multiple ischemic diseases.However,conventional topical drug delivery often results in a burst release of the drug,leading to transient retention(inefficacy)and undesirable diffusion(toxicity)in vivo.Therefore,a drug delivery system that responds to changes in the microenvironment of tissue regeneration and controls vascular endothelial growth factor release is crucial to improve the treatment of ischemic stroke.Matrix metalloproteinase-2(MMP-2)is gradually upregulated after cerebral ischemia.Herein,vascular endothelial growth factor mimic peptide QK was self-assembled with MMP-2-cleaved peptide PLGLAG(TIMP)and customizable peptide amphiphilic(PA)molecules to construct nanofiber hydrogel PA-TIMP-QK.PA-TIMP-QK was found to control the delivery of QK by MMP-2 upregulation after cerebral ischemia/reperfusion and had a similar biological activity with vascular endothelial growth factor in vitro.The results indicated that PA-TIMP-QK promoted neuronal survival,restored local blood circulation,reduced blood-brain barrier permeability,and restored motor function.These findings suggest that the self-assembling nanofiber hydrogel PA-TIMP-QK may provide an intelligent drug delivery system that responds to the microenvironment and promotes regeneration and repair after cerebral ischemia/reperfusion injury.展开更多
Since 2023,the Spring Festival holiday tourism market has recovered significantly,and the market value has steadily increased.According to the newly revised Regulation on Public Holidays for National Annual Festivals ...Since 2023,the Spring Festival holiday tourism market has recovered significantly,and the market value has steadily increased.According to the newly revised Regulation on Public Holidays for National Annual Festivals and Memorial Days and some holiday arrangements in 2025,since 2025,New Year’s Eve has been included as a statutory holiday,and the benefits of increasing the Spring Festival holiday to 8 days have further ignited everyone’s enthusiasm for Spring Festival travel.展开更多
On February 21,China Institute of International Studies (CIIS) released the special research report"China-Russia Relations in the New Era."Assistant Minister of Foreign Affairs Liu Bin and Russian Ambassador...On February 21,China Institute of International Studies (CIIS) released the special research report"China-Russia Relations in the New Era."Assistant Minister of Foreign Affairs Liu Bin and Russian Ambassador to China Igor Morgulov attended the release conference and delivered speeches.CIIS President Chen Bo presided over the event and introduced the main content of the report.展开更多
In view of the time-consuming and unreliable deficiencies of the cross-axis work piece in the clamping process,combined with the working characteristics of the eccentric mechanism,a simple and fast eccentric locking m...In view of the time-consuming and unreliable deficiencies of the cross-axis work piece in the clamping process,combined with the working characteristics of the eccentric mechanism,a simple and fast eccentric locking mechanism is designed.The push rod iquickly driven by the combined action of the handle and the drum,so that the cross shaft work piece can be quickly locked in the axial direction.The eccentric locking mechanism not only has simple operation and convenient maintenance,but also has the characteristics of low manufacturing cost and high life,and has certain reference value for future special fixture design.展开更多
Zirconium,titanium,and other hexagonally close-packed(HCP)metals and their alloys are representative high specific strength,high reaction enthalpy,and high thermal conductivity structural materials.In this study,two t...Zirconium,titanium,and other hexagonally close-packed(HCP)metals and their alloys are representative high specific strength,high reaction enthalpy,and high thermal conductivity structural materials.In this study,two typical HCP metals,zirconium,and titanium,were applied to reactive materials(RMs)to prepare Zr/PTFE/W RMs and Ti/PTFE/W RMs,validating the feasibility of HCP metal/PTFE/W RMs.The impact response process of typical HCP metal/PTFE/W RMs under high-velocity dynamic loads was studied using shock equations of state(EOS)based on porous mixtures and chemical reaction kinetics equations.An improved hemispherical quasi-sealed test chamber was employed to measure the energy release characteristic curves of 10 types of Zr/PTFE/W RMs and Ti/PTFE/W RMs under impact velocities ranging from 500 m/s to 1300 m/s.The datasets of the impact-induced energy release characteristics of HCP metal/PTFE/W RMs were established.Additionally,the energy release efficiency of HCP metal/PTFE/W RMs under impact was predicted using the support vector regression(SVR)kernel function model.The datasets of Zr/PTFE/W RMs and Ti/PTFE/W RMs with W contents of 0%,25%,50%,and 75%were used as test sets,respectively.The model predictions showed a high degree of agreement with the experimental data,with mean absolute errors(MAE)of 4.8,6.5,4.6,and 4.1,respectively.展开更多
A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise...A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise. Like many low phase noise oscillators, a cavity magnonic oscillator faces the challenge that its narrow resonance profile is not well suited for injection locking amplification. This work presents an improved design for such an oscillator configured as an injection locking amplifier(ILA) with an extended lock range. The proposed design features a two-stage architecture, consisting of a pre-amplification oscillator and a cavity magnonic oscillator, separated by an isolator to prevent backward locking.By optimizing the circuit parameters of each stage, the proposed design achieved an order of magnitude increase in lock range, when compared to its predecessors, all while preserving the phase noise quality of the input, making it well-suited for narrowband, sensitive signal amplification. Furthermore, this work provides a method for using oscillators with high spectral purity as injection locking amplifiers.展开更多
As a major fault in the northeastern Qinghai-Xizang Plateau,the Haiyuan fault zone is important for understanding the regional deformation.Aiming at the differences in the slip rate and locking degree obtained from di...As a major fault in the northeastern Qinghai-Xizang Plateau,the Haiyuan fault zone is important for understanding the regional deformation.Aiming at the differences in the slip rate and locking degree obtained from different studies,this study constructs a refined block model(including Qilian,Alxa,Ordos,Xining,Haiyuan,and Lanzhou blocks)and uses the grid search and simulated annealing methods to invert GPS data for slip rate and locking degree of the Haiyuan fault zone.The results are as follows:(1)The sinistral slip rates in the western,middle,and eastern segments are 4.93-5.22 mm/a,1.52-4.94 mm/a,and 0.43-1.18 mm/a,decreasing eastward on the whole,while the compression rates are 0.45-1.26 mm/a,0.58-2.62 mm/a,and3.52-4.48 mm/a,increasing eastward on the whole.(2)The locking depth of the western segment increases from about 5 km to about 20 km eastward;the middle segment decreases and then increases eastward;the eastern segment concentrates at about 20 km(PHI is about 0.86).(3)The slip deficit is relatively higher in the Lenglongling,Jinqianghe,Maomaoshan,and Liupanshan faults(averaging about 3.42 mm/a,4.16 mm/a,4.23 mm/a,and 3.43 mm/a within 20 km).(4)The Qilian,Alxa,Xining,Lanzhou,and Haiyuan blocks rotate clockwise,while the Ordos block rotates counterclockwise.Additionally,by comparing different block models,the Haiyuan block should be considered independently.The Haiyuan fault zone adjusts surrounding block movements and uplifts Liupanshan mountain tectonically.The results can provide important references for understanding the regional earthquake risk and deformation mechanism.展开更多
The high necessity to develop novel and optimized technologies for crop production is very high due to the exponential growth in term of world population of the last years.In this field a novel use of fertilizers and ...The high necessity to develop novel and optimized technologies for crop production is very high due to the exponential growth in term of world population of the last years.In this field a novel use of fertilizers and pesticides can ameliorate the life conditions around the world due to the higher productivity with lower losses and consequent less environmental problems related to pollution.To address these challenges a very promising solution is constituted by devices able to control and sustain the release of fertilizers and pesticide optimizing their efficacy preserving the environment.In the last decade a lot of efforts,in terms of research,were dedicated to the development of smart devices that can address those issues maintaining also low costs and easy production processes.In this review we will point the attention on devices that can be used as slow release systems for fertilizers and/or pesticides.In details strong consideration will be devoted to their formulation to increase the knowledge on the high number of possibilities behind these novel and smart devices.展开更多
C-glycosides have been demonstrated to have distinct biological functions and therefore display notable pharmacological values,whereas the access to the versatile structural analog of C-glycosides is a significant cha...C-glycosides have been demonstrated to have distinct biological functions and therefore display notable pharmacological values,whereas the access to the versatile structural analog of C-glycosides is a significant challenge to their advancement as therapeutic agents.We herein disclose a facial and efficient catalytic C-glycosylation using a glycosyl ortho-2,2-dimethoxycarbony lcyclopropylbenzoate(CCBz)as the donor.The trailblazing glycosyl donor can be simply activated by a non-toxic and easily accessible Sc(Ⅲ)catalyst.The ring-strain release of the incorporated donor-acceptor cyclopropane(DAC)serves as a powerful driving force of the glycosylation system.The adaptability of current methods to different types of donors and acceptors was exemplified.Examinations on the synthetic potential were done with the one-pot synthesis of free C-indolyl-glycosides and the subsequent biological studies,unlocking the antibacterial potentials of these compounds.展开更多
Nanocarrier-based drug delivery systems(nDDSs)present significant opportunities for improving disease treatment,offering advantages in drug encapsulation,solubilization,stability enhancement,and optimized pharmacokine...Nanocarrier-based drug delivery systems(nDDSs)present significant opportunities for improving disease treatment,offering advantages in drug encapsulation,solubilization,stability enhancement,and optimized pharmacokinetics and biodistribution.n DDSs,comprising lipid,polymeric,protein,and inorganic nanovehicles,can be guided by or respond to biological cues for precise disease treatment and management.Equipping nanocarriers with tissue/celltargeted ligands enables effective navigation in complex environments,while functionalization with stimuli-responsive moieties facilitates site-specific controlled release.These strategies enhance drug delivery efficiency,augment therapeutic efficacy,and reduce side effects.This article reviews recent strategies and ongoing advancements in n DDSs for targeted drug delivery and controlled release,examining lesion-targeted nanomedicines through surface modification with small molecules,peptides,antibodies,carbohydrates,or cell membranes,and controlled-release nanocarriers responding to endogenous signals such as pH,redox conditions,enzymes,or external triggers like light,temperature,and magnetism.The article also discusses perspectives on future developments.展开更多
Eutrophication is a significant challenge for surface water,with sediment phosphorus(P)release being a key contributor.Although biological aluminum-based P-inactivation agent(BA-PIA)has shown effectiveness in controll...Eutrophication is a significant challenge for surface water,with sediment phosphorus(P)release being a key contributor.Although biological aluminum-based P-inactivation agent(BA-PIA)has shown effectiveness in controlling P release from sediment,the efficiency and mechanism by BA-PIA capping is still not fully understood.This study explored the efficiency and mechanism of using BA-PIA capping controlling P release from sediment.The main mechanisms controlling P release from sediment via BA-PIA capping involved transforming mobile and less stable fractions into stable ones,passivating DGT-labile P and establishing a 13 mm’P static layer’within the sediment.Additionally,BA-PIA’s impact on Fe redox processes significantly influenced P release from the sediment.After BA-PIA capping,notable reductionswere observed in total P,soluble reactive P(SRP),and diffusive gradient in thin-films(DGT)-measured labile P(DGT-labile P)concentration in the overlying water,with reduction rates of 95.6%,92.7%,and 96.5%,respectively.After BA-PIA capping,the diffusion flux of SRP across the sediment-water interface and the apparent P diffusion flux decreased by 91.3%and 97.8%,respectively.Additionally,BA-PIA capping led to reduced concentrations of SRP,DGT-labile P,and DGT-measured labile Fe(II)in the sediment interstitial water.Notably,BA-PIA capping significantly reduced P content and facilitated transformation in the 0∼30 mm sediment layers but not in the 30∼45 mm and 45∼60 mm sediment layers for NaOH-extractable inorganic P and HCl-extracted P.These findings offer a theoretical basis and technical support for the practical application of BA-PIA capping to control P release from sediment.展开更多
文摘Conventional locking/release mechanisms often face challenges in aircraft wing separation processes,such as excessive impact loads and insufficient synchronization.These may cause structural damage to the airframe or attitude instability,seriously compromising mission reliability.To address this engineering challenge,this paper proposes a multi-point low-impact locking/release mechanism based on the mobility model and energy conversion strategy.Through establishing a DOF constraint framework system,this paper systematically analyzes the energy transfer and conversion characteristics during the wing separation process,reveals the generation mechanism of impact loads,and conducts research on low-impact design based on energy conversion strategy.Building on this foundation,a single-point locking/release mechanism employing parallel trapezoidal key shaft structure was designed,which increases frictional contact time and reduces the energy release rate,thereby achieving low-impact characteristics.The mechanism's performance was validated through physical prototype development and systematic functional testing(including unlocking force,synchronization,and impact tests).Experimental results demonstrate:(1)Under 14 kN preload condition,the maximum unlocking force was only 92.54 N,showing a linear relationship with preload that satisfies the"strong-connection/weak-unlock"design requirement;(2)Wing separation was completed within 46 ms,with synchronization time difference among three separation mechanisms stably controlled within 12-14 ms,proving rapid and reliable operation;(3)The unlocking impact acceleration ranged between 26 and 73 g,below the 100 g design limit,confirming the effectiveness of the energy conversion strategy.The proposed low-impact locking/release mechanism design method based on energy conversion strategy resolves the traditional challenges of high impact and synchronization deficiencies.The synergistic optimization mechanism of"structural load reduction and performance improvement"provides a highly reliable technical solution for wing separable mechanisms while offering novel design insights for wing connection/separation systems engineering.
基金supported by the National Key R&D Program of China(2023YFB2407900)the National Natural Science Foundation of China(52302512)+1 种基金State Key Laboratory of New Ceramic and Fine Processing Tsinghua University(KFZD202305)Zhejiang Province Science and Technology Program Grant(2024C0127(SD2))。
文摘Cascading thermal runaway(TR)propagation poses a critical safety concern for large-format sodium-ion battery(SIB)systems because of the heightened risks of fires or explosions.However,effectively suppressing TR propagation without introducing unintended side effects remains a significant challenge.Herein,we demonstrate a localized energy release method to mitigate TR,by reducing the state of charge(SOC)of cells adjacent to the thermally runaway unit.We discover that as the SOCs decreased from 100%to 25%,the TR trigger temperature decreased significantly,and the maximum temperature decrease from 367 to 229℃.Meanwhile,the volume of gas decreased to one-third of its original value,while the range of explosion limits significantly narrowed.The analysis of the morphology of the debris further confirms that the structural damage is greater at higher SOC levels.Moreover,an Entropy Weight and Technique for Order Preference by Similarity to an Ideal Solution(EW-TOPSIS)method has been established to assess the safety status of SIBs,showing that the TR possibility is nearly linear with the SOCs,and the TR hazard is exponentially related to the SOCs.Finally,when the SOC of cells adjacent to the TR cell is reduced to 25%,TR can be directly blocked without the need for additional cooling or thermal insulation methods.This study not only advances the understanding of TR behavior in SIBs but also offers a straightforward approach to mitigating the TR risk in SIB systems.
基金Funded by the National 863 Project of China (No. 2004AA215162)
文摘To assess the merits of PEGylated poly （lactic-co-glycolic acid） （PEG-PLGA） nanoparticles as drug carriers for tumor necrosis factor-α receptor blocking peptide （TNFR-BP）, PEG-PLGA copolymer, which could be used to prepare the stealth nanoparticles, was synthesized with methoxypolyethyleneglycol, DL-lactide and glycolide. The structure of PEG-PLGA was confirmed with ^1H-NMR and FT-IR spectroscopy, and the molecular weight （MW） was determined by gel permeation chromatography. Fluorescent FITC-TNFR- BP was chosen as model protein and encapsulated within PEG-PLGA nanoparticles using the double emulsion method. Atomic force microscopy and photon correlation spectroscopy were employed to characterize the stealth nanoparticles fabricated for morphology, size with polydispersity index and zeta potential. Encapsulation efficiency （EE） and the release of FITC-TNFR-BP in nanopartieles in vitro were measured by the fluorescence measurement. The stealth nanoparticles were found to have the mean diameter less than 270 nm and zeta potential less than -20 mV. In all nanoparticle formulations, more than 45% of EE were obtained. FITC-TNFR-BP release from the PEG-PLGA nanoparticles exhibited a biphasic pattern, initial burst release and consequently sustained release. The experimental results show that PEG-PLGA nanoparticles possess the potential to develop as drug carriers for controlled release applications of TNFR-BP.
基金supported by the National Natural Science Foundation of China(Nos.51808158,52170101,and 52200116)Tianjin Natural Science Foundation(No.23JCYBJC00640).
文摘The electrochemical corrosion of ductile pipes(DPs)in drinking water distribution systems(DWDS)has a crucial impact on cement-mortar lining(CML)failure and metal release,potentially leading to drinking water quality deterioration and posing a risk to public health.An in-situ scanning vibrating electrode technique(SVET)with micron-scale resolution,microscopic scale detection and water quality analysis were used to investigate the corrosion behavior and metal release from DPs throughout the whole CML failure process.Metal pollutants release occurred at three different stages of CML failure process,and there are potential risks of water quality deterioration exceeding the maximum allowable levels set by national standards in the partial failure stage and lining peeling stage.Furthermore,the effects of water chemistry(Cl^(−),SO_(4)^(2−),NO_(3)−,and Ca^(2+))on corrosion scale growth and iron release activity,were investigated during the CML partial failure stage.Results showed that the CML failure process in DPs was accelerated by the autocatalysis of localized corrosion.Cl^(−)was found to damage the uncorroded metal surface,while SO_(4)^(2−)mainly dissolved the corrosion scale surface,increasing iron release.Both the oxidation of NO_(3)−and selective sedimentation of Ca2+were found to enhance the stability of corrosion scales and inhibit iron release.
基金supported by National Natural Science Foundation of China(Nos.51806092,52201410)Non-Carbon Energy Conversion and Utilization Institute under the Shanghai Class IV Peak Disciplinary Development Program,High-End Foreign Experts Recruitment Plan of China(G2022013028L).
文摘Phase Change Material(PCM)-based cold energy storage system(CESS)can effectively utilize the peak and valley power resources to reduce the excessive dependence on the power grid.In this study,a PCM-based CESS was designed for cold storage applications.The optimal number of PCM plates was determined through numerical simulations to meet the required cold storage temperature and control time.Additionally,the air temperature field,flow field,and melting characteristics of the PCMplates during the cooling release process were analyzed.The effects of plate positioning and thickness on the cooling release performance were further investigated.The results indicated that when 64PCMplateswere used,the duration formaintaining temperatures below−18℃increased from0.6 h to approximately 16.94 h.During the cooling release process,the temperature field in the cold storage exhibited stratification,and the melting of the PCM plates was non-uniform.Placing the PCM plates at the top or within the interlayers without cargo above proved more effective,with their cooling release power being approximately twice that of the PCM plates placed in the interlayers with cargo above.Furthermore,reducing the thickness of the PCMplates from15 to 7.5mmresulted in a 3.6-h increase in the time below−18℃and a 4.5-h reduction in the time required to reach 80%liquid phase fraction.
文摘Naturally degradable capsule provides a platform for sustained fragrance release.However,practical challenges such as low encapsulation efficiency and difficulty in sustained release are still limited in using fragranceloaded capsules.In this work,the natural materials sodium alginate and gelatine are dissolved and act as the aqueous phase,lavender is dissolved in caprylic/capric triglyceride(GTCC)as the oil phase,and SiO_(2) nanoparticles with neutralwettability as a solid emulsifier to form O/W Pickering emulsions simultaneously.Finally,multi-core capsules are prepared using the drop injection method with emulsions as templates.The results show that the capsules have been successfully prepared with a spherical morphology and multi-core structure,and the encapsulation rate of multi-core capsules can reach up to 99.6%.In addition,the multi-core capsules possess desirable sustained release performance,the cumulative sustained release rate of fragrance at 25℃over 49 days is only 32.5%.It is attributed to the significant protection of multi-core structure,Pickering emulsion nanoparticle membranes,and hydrogel network shell for encapsulated fragrance.This study is designed to deliver a new strategy for using sustained-release technology with fragrance in food,cosmetics,textiles,and other fields.
基金Supported by Shaoxing Health Science and Technology Program,No.2022SY016,No.2022KY010.
文摘BACKGROUND In recent years,immune checkpoint inhibitors(ICIs)have demonstrated remarkable efficacy across diverse malignancies.Notably,in patients with advanced gastric cancer,the use of programmed death 1(PD-1)blockade has significantly prolonged overall survival,marking a pivotal advancement comparable to the impact of Herceptin over the past two decades.While the therapeutic benefits of ICIs are evident,the increasing use of immunotherapy has led to an increase in immune-related adverse events.CASE SUMMARY This article presents the case of a patient with advanced gastric cancer and chronic plaque psoriasis.Following sintilimab therapy,the patient developed severe rashes accompanied by cytokine release syndrome(CRS).Fortunately,effective management was achieved through the administration of glucocorticoid,tocilizumab,and acitretin,which resulted in favorable outcomes.CONCLUSION Glucocorticoid and tocilizumab therapy was effective in managing CRS after PD-1 blockade therapy for gastric cancer in a patient with chronic plaque psoriasis.
文摘Pearl millet, Pennisetum glaucum (Leeke) R. Br, is the main cereal crop in Niger. This crop is seriously attacked by the millet Head miner (MHM), Heliocheilus albipunctella (de Joannis) (Lepidoptera, Noctuidae) causing significant yield losses. This study to optimize biological control of this pest was carried out in Niger in the laboratory and in a farming environment. In the laboratory, the larval paralysis and emergence of the parasitoid Habrobracon hebetor Say (Hymenoptera: Braconidae) were compared between release jute bags, plastic boxes and cardboard boxes. In a farming environment, direct releases were carried out with plastic boxes and releases with jute bags in 12 villages of the Maradi region during the cropping seasons of 2021 and 2022. The results indicated that 25 larvae of Corcyra cephalonica Stainton (Lepidoptera: Pyralidae) in the boxes were all paralyzed by 2 females of H. hebetor within 7 hours 30 minutes. The emergence of adults began on the 7th day after the beginning of the experiment for a period of two weeks and three weeks respectively in the boxes and jute bags. The production varied from 107.08 to 110.17 parasitoids and was comparable between the Jute bags, plastic boxes and cardboard boxes. In Farmers’ fields, the parasitoid release with the two methods caused the parasitism rates that varied from 64.32 to 66.52% depending on the year but in 2022 the rate of parasitism was higher in the fields with direct releases using plastic boxes (72.66%) compared to those released with jute bags (56.35%). Plastic boxes and cardboard boxes can be used for the production of the H. hebetor parasitoids. These results can be recommended to the cottage industries in the Sahel in order to improve the production and release methods of H. hebetor and make them more adapted to farmers’ fields.
基金supported by the Natural Science Foundation of Shandong Province,No.ZR2023MC168the National Natural Science Foundation of China,No.31670989the Key R&D Program of Shandong Province,No.2019GSF107037(all to CS).
文摘Vascular endothelial growth factor and its mimic peptide KLTWQELYQLKYKGI(QK)are widely used as the most potent angiogenic factors for the treatment of multiple ischemic diseases.However,conventional topical drug delivery often results in a burst release of the drug,leading to transient retention(inefficacy)and undesirable diffusion(toxicity)in vivo.Therefore,a drug delivery system that responds to changes in the microenvironment of tissue regeneration and controls vascular endothelial growth factor release is crucial to improve the treatment of ischemic stroke.Matrix metalloproteinase-2(MMP-2)is gradually upregulated after cerebral ischemia.Herein,vascular endothelial growth factor mimic peptide QK was self-assembled with MMP-2-cleaved peptide PLGLAG(TIMP)and customizable peptide amphiphilic(PA)molecules to construct nanofiber hydrogel PA-TIMP-QK.PA-TIMP-QK was found to control the delivery of QK by MMP-2 upregulation after cerebral ischemia/reperfusion and had a similar biological activity with vascular endothelial growth factor in vitro.The results indicated that PA-TIMP-QK promoted neuronal survival,restored local blood circulation,reduced blood-brain barrier permeability,and restored motor function.These findings suggest that the self-assembling nanofiber hydrogel PA-TIMP-QK may provide an intelligent drug delivery system that responds to the microenvironment and promotes regeneration and repair after cerebral ischemia/reperfusion injury.
文摘Since 2023,the Spring Festival holiday tourism market has recovered significantly,and the market value has steadily increased.According to the newly revised Regulation on Public Holidays for National Annual Festivals and Memorial Days and some holiday arrangements in 2025,since 2025,New Year’s Eve has been included as a statutory holiday,and the benefits of increasing the Spring Festival holiday to 8 days have further ignited everyone’s enthusiasm for Spring Festival travel.
文摘On February 21,China Institute of International Studies (CIIS) released the special research report"China-Russia Relations in the New Era."Assistant Minister of Foreign Affairs Liu Bin and Russian Ambassador to China Igor Morgulov attended the release conference and delivered speeches.CIIS President Chen Bo presided over the event and introduced the main content of the report.
文摘In view of the time-consuming and unreliable deficiencies of the cross-axis work piece in the clamping process,combined with the working characteristics of the eccentric mechanism,a simple and fast eccentric locking mechanism is designed.The push rod iquickly driven by the combined action of the handle and the drum,so that the cross shaft work piece can be quickly locked in the axial direction.The eccentric locking mechanism not only has simple operation and convenient maintenance,but also has the characteristics of low manufacturing cost and high life,and has certain reference value for future special fixture design.
基金sponsored by the National Natural Science Foundation of China(Grant Nos.U2241285,62201267)。
文摘Zirconium,titanium,and other hexagonally close-packed(HCP)metals and their alloys are representative high specific strength,high reaction enthalpy,and high thermal conductivity structural materials.In this study,two typical HCP metals,zirconium,and titanium,were applied to reactive materials(RMs)to prepare Zr/PTFE/W RMs and Ti/PTFE/W RMs,validating the feasibility of HCP metal/PTFE/W RMs.The impact response process of typical HCP metal/PTFE/W RMs under high-velocity dynamic loads was studied using shock equations of state(EOS)based on porous mixtures and chemical reaction kinetics equations.An improved hemispherical quasi-sealed test chamber was employed to measure the energy release characteristic curves of 10 types of Zr/PTFE/W RMs and Ti/PTFE/W RMs under impact velocities ranging from 500 m/s to 1300 m/s.The datasets of the impact-induced energy release characteristics of HCP metal/PTFE/W RMs were established.Additionally,the energy release efficiency of HCP metal/PTFE/W RMs under impact was predicted using the support vector regression(SVR)kernel function model.The datasets of Zr/PTFE/W RMs and Ti/PTFE/W RMs with W contents of 0%,25%,50%,and 75%were used as test sets,respectively.The model predictions showed a high degree of agreement with the experimental data,with mean absolute errors(MAE)of 4.8,6.5,4.6,and 4.1,respectively.
基金funded by NSERC Discovery Grants, NSERC Discovery Accelerator Supplements, Innovation Proof-of-Concept Grant of Research Manitoba, and Faculty of Science Research Innovation and Commercialization Grant of University of Manitoba (C.-M.H.)。
文摘A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise. Like many low phase noise oscillators, a cavity magnonic oscillator faces the challenge that its narrow resonance profile is not well suited for injection locking amplification. This work presents an improved design for such an oscillator configured as an injection locking amplifier(ILA) with an extended lock range. The proposed design features a two-stage architecture, consisting of a pre-amplification oscillator and a cavity magnonic oscillator, separated by an isolator to prevent backward locking.By optimizing the circuit parameters of each stage, the proposed design achieved an order of magnitude increase in lock range, when compared to its predecessors, all while preserving the phase noise quality of the input, making it well-suited for narrowband, sensitive signal amplification. Furthermore, this work provides a method for using oscillators with high spectral purity as injection locking amplifiers.
基金supported by the National Natural Science Foundation of China(42474003,42074007)the Fundamental Research Funds for the Central Universities(2042023kfyq01)。
文摘As a major fault in the northeastern Qinghai-Xizang Plateau,the Haiyuan fault zone is important for understanding the regional deformation.Aiming at the differences in the slip rate and locking degree obtained from different studies,this study constructs a refined block model(including Qilian,Alxa,Ordos,Xining,Haiyuan,and Lanzhou blocks)and uses the grid search and simulated annealing methods to invert GPS data for slip rate and locking degree of the Haiyuan fault zone.The results are as follows:(1)The sinistral slip rates in the western,middle,and eastern segments are 4.93-5.22 mm/a,1.52-4.94 mm/a,and 0.43-1.18 mm/a,decreasing eastward on the whole,while the compression rates are 0.45-1.26 mm/a,0.58-2.62 mm/a,and3.52-4.48 mm/a,increasing eastward on the whole.(2)The locking depth of the western segment increases from about 5 km to about 20 km eastward;the middle segment decreases and then increases eastward;the eastern segment concentrates at about 20 km(PHI is about 0.86).(3)The slip deficit is relatively higher in the Lenglongling,Jinqianghe,Maomaoshan,and Liupanshan faults(averaging about 3.42 mm/a,4.16 mm/a,4.23 mm/a,and 3.43 mm/a within 20 km).(4)The Qilian,Alxa,Xining,Lanzhou,and Haiyuan blocks rotate clockwise,while the Ordos block rotates counterclockwise.Additionally,by comparing different block models,the Haiyuan block should be considered independently.The Haiyuan fault zone adjusts surrounding block movements and uplifts Liupanshan mountain tectonically.The results can provide important references for understanding the regional earthquake risk and deformation mechanism.
文摘The high necessity to develop novel and optimized technologies for crop production is very high due to the exponential growth in term of world population of the last years.In this field a novel use of fertilizers and pesticides can ameliorate the life conditions around the world due to the higher productivity with lower losses and consequent less environmental problems related to pollution.To address these challenges a very promising solution is constituted by devices able to control and sustain the release of fertilizers and pesticide optimizing their efficacy preserving the environment.In the last decade a lot of efforts,in terms of research,were dedicated to the development of smart devices that can address those issues maintaining also low costs and easy production processes.In this review we will point the attention on devices that can be used as slow release systems for fertilizers and/or pesticides.In details strong consideration will be devoted to their formulation to increase the knowledge on the high number of possibilities behind these novel and smart devices.
基金Ministry of Education(MOE-T2EP30120-0007,Tier-1 RG107/23)of Singapore for the financial support.
文摘C-glycosides have been demonstrated to have distinct biological functions and therefore display notable pharmacological values,whereas the access to the versatile structural analog of C-glycosides is a significant challenge to their advancement as therapeutic agents.We herein disclose a facial and efficient catalytic C-glycosylation using a glycosyl ortho-2,2-dimethoxycarbony lcyclopropylbenzoate(CCBz)as the donor.The trailblazing glycosyl donor can be simply activated by a non-toxic and easily accessible Sc(Ⅲ)catalyst.The ring-strain release of the incorporated donor-acceptor cyclopropane(DAC)serves as a powerful driving force of the glycosylation system.The adaptability of current methods to different types of donors and acceptors was exemplified.Examinations on the synthetic potential were done with the one-pot synthesis of free C-indolyl-glycosides and the subsequent biological studies,unlocking the antibacterial potentials of these compounds.
基金supported by the National Natural Science Foundation of China(No.82273876)the Fok Ying-Tong Education Foundation for Young Teachers in the Higher Education Institutions of China(No.171028)+1 种基金the Project of State Key Laboratory of Advanced Drug Delivery and Release Systems(No.DSQZZD-200301)the Fundamental Research Fund for the Central Universities(No.2632022YC02)。
文摘Nanocarrier-based drug delivery systems(nDDSs)present significant opportunities for improving disease treatment,offering advantages in drug encapsulation,solubilization,stability enhancement,and optimized pharmacokinetics and biodistribution.n DDSs,comprising lipid,polymeric,protein,and inorganic nanovehicles,can be guided by or respond to biological cues for precise disease treatment and management.Equipping nanocarriers with tissue/celltargeted ligands enables effective navigation in complex environments,while functionalization with stimuli-responsive moieties facilitates site-specific controlled release.These strategies enhance drug delivery efficiency,augment therapeutic efficacy,and reduce side effects.This article reviews recent strategies and ongoing advancements in n DDSs for targeted drug delivery and controlled release,examining lesion-targeted nanomedicines through surface modification with small molecules,peptides,antibodies,carbohydrates,or cell membranes,and controlled-release nanocarriers responding to endogenous signals such as pH,redox conditions,enzymes,or external triggers like light,temperature,and magnetism.The article also discusses perspectives on future developments.
基金supported by the National Natural Science Foundation of China(No.51878300)the National Natural Science Foundation of Xiamen City(No.3502Z202373041)the Water Conservancy Science and Technology Plan Project(No.RC2127).
文摘Eutrophication is a significant challenge for surface water,with sediment phosphorus(P)release being a key contributor.Although biological aluminum-based P-inactivation agent(BA-PIA)has shown effectiveness in controlling P release from sediment,the efficiency and mechanism by BA-PIA capping is still not fully understood.This study explored the efficiency and mechanism of using BA-PIA capping controlling P release from sediment.The main mechanisms controlling P release from sediment via BA-PIA capping involved transforming mobile and less stable fractions into stable ones,passivating DGT-labile P and establishing a 13 mm’P static layer’within the sediment.Additionally,BA-PIA’s impact on Fe redox processes significantly influenced P release from the sediment.After BA-PIA capping,notable reductionswere observed in total P,soluble reactive P(SRP),and diffusive gradient in thin-films(DGT)-measured labile P(DGT-labile P)concentration in the overlying water,with reduction rates of 95.6%,92.7%,and 96.5%,respectively.After BA-PIA capping,the diffusion flux of SRP across the sediment-water interface and the apparent P diffusion flux decreased by 91.3%and 97.8%,respectively.Additionally,BA-PIA capping led to reduced concentrations of SRP,DGT-labile P,and DGT-measured labile Fe(II)in the sediment interstitial water.Notably,BA-PIA capping significantly reduced P content and facilitated transformation in the 0∼30 mm sediment layers but not in the 30∼45 mm and 45∼60 mm sediment layers for NaOH-extractable inorganic P and HCl-extracted P.These findings offer a theoretical basis and technical support for the practical application of BA-PIA capping to control P release from sediment.
