The near crack line analysis method was used to investigate a crack loaded by a pair of point shear forces in an infinite plate in an elastic-perfectly plastic solid. The analytical solution was obtained, that is the ...The near crack line analysis method was used to investigate a crack loaded by a pair of point shear forces in an infinite plate in an elastic-perfectly plastic solid. The analytical solution was obtained, that is the elastic-plastic fields near crack line and law that the length of the plastic zone along the crack line is varied with external loads. The results are sufficiently precise near the crack line and are not confined by small scale yielding conditions.展开更多
In this paper, the improved near crack line analysis method proposed in Refs. [1] and [2] is used to investigate a center crack loaded by two pairs of antiplane point forces in a finite plate in an elastic-perfectly p...In this paper, the improved near crack line analysis method proposed in Refs. [1] and [2] is used to investigate a center crack loaded by two pairs of antiplane point forces in a finite plate in an elastic-perfectly plastic solid. And the analytical solutions are obtained, that is elastic-plastic stress fields near the crack line and the law that the length of the plastic zone along the crack line is varied with an external loads tr,ld the bearing capacity of a finite plate with a center crack. The results of this paper are sufficiently precise near the crack line, because the assumptions of the small scale yielding theory have not been used and no other assumptions have been taken.展开更多
In this paper, an adaptive line spectral pair filter is derived from an adaptive lattice filter. A least-mean-square(LMS) type adaptive algorithm used to calculate directly the line spectral pair(LSP) coefficients on ...In this paper, an adaptive line spectral pair filter is derived from an adaptive lattice filter. A least-mean-square(LMS) type adaptive algorithm used to calculate directly the line spectral pair(LSP) coefficients on a stage-by-stage basis is presented. Experimental results show that the algorithm has higher convergence rate and lower misadjustment as compared with the other algorithms. The LSP coefficients calculated by the algorithm have been used to carry out speech linear predictive synthesis, resulting in better results than PARCOR coefficients.展开更多
Measuring and reconstructing the shape of workpieces have been considered as a fundamental step in both reverse engineering and product quality control.Owing to increasing structural complexity of recent products,meas...Measuring and reconstructing the shape of workpieces have been considered as a fundamental step in both reverse engineering and product quality control.Owing to increasing structural complexity of recent products,measurements from multiple directions are typically required in current scanning techniques.Specifically,the plane structured light can be applied to measure one area of a part at a time,with an additional algorithm required to merge the collected data of each area.Alternatively,the line structured light sensor integrated on CNC machines or CMMs could also realize multi-view measurement.However,the system needs to be repeatedly calibrated at each new direction.This paper presents a flexible scanning method by integrating laser line sensors with articulated arm coordinate measuring machines(AACMM).Since the output of the laser line sensor is 2D raw data in the laser plane,our system model introduces an explicit transformation from the 2D sensor coordinate frame to the 3D base coordinate frame of the AACMM(i.e.,the translation and rotation the of the 2D sensor coordinate in the sixth coordinate system of AACMM).To solve the model,the“conjugate pairs”are proposed and identified by measuring a fixed point(e.g.,a sphere center).Moreover,a search algorithm is adopted to find the optimal solution,which noticeably boosts the model accuracy.The experimental results show that the error of the system is about 0.2 mm,which is caused by the error of the AACMM,the sensor error and the calibration error.By measuring a complicated part,the proposed system is proved to be flexible and facilitate,with the ability to measure a part expediently from any necessary direction.Furthermore,the proposed calibration method can also be used for robot hand-eye relationship calibration.展开更多
The improved near crack line analysis method was used to investigate an eccentric cracked plate loaded by two pairs of anti_plane point forces at the crack surface in an elastic_perfectly plastic solid. The analytical...The improved near crack line analysis method was used to investigate an eccentric cracked plate loaded by two pairs of anti_plane point forces at the crack surface in an elastic_perfectly plastic solid. The analytical solutions of the elastic_plastic stress fields and displacements near the crack line have been found without the assumptions of the small scale yielding. The law that the length of the plastic zone along the crack line is varied with an external loads and the bearing capacity of an eccentric cracked plate are obtained.展开更多
The near crack line analysis method was used to investigate a crack loaded by two pairs of point shear forces in an infinite plate in an elastic-perfectly plastic solid, and the analytical solution was obtained. The s...The near crack line analysis method was used to investigate a crack loaded by two pairs of point shear forces in an infinite plate in an elastic-perfectly plastic solid, and the analytical solution was obtained. The solutions include: the unit normal vector of the elastic-plastic boundary near the crack line, the elastic-plastic stress fields near crack line, law that the length of the plastic zone along the crack line is varied with an external loads, and the bearing capacity of an infinite plate with a center crack loaded by two pairs of point shear forces. The results are sufficiently precise near the crack line because the assumptions of the small scale yielding theory have not been made and no other assumption have been taken.展开更多
In the framework of phenomenological time-dependent Ginzburg-Landau（TDGL） formalism,the dynamical properties of vortex-antivortex（V-Av） pair in a superconductor film with a narrow slit was studied.The slit positio...In the framework of phenomenological time-dependent Ginzburg-Landau（TDGL） formalism,the dynamical properties of vortex-antivortex（V-Av） pair in a superconductor film with a narrow slit was studied.The slit position and length can have a great impact not only on the vortex dynamical behavior but also the current-voltage（Ⅰ-Ⅴ） characteristics of the sample.Kinematic vortex lines can be predominated by the location of the slit.In the range of relatively low applied currents for a constant weak magnetic field,kinematic vortex line appears at right or left side of the slit by turns periodically.We found such single-side kinematic vortex line cannot lead to a jump in the Ⅰ-Ⅴ curve.At higher applied currents the phase-slip lines can be observed at left and right sides of the slit simultaneously.The competition between the vortex created at the lateral edge of the sample and the V-Av pair in the slit will result in three distinctly different scenarios of vortex dynamics depending on slit length：the lateral vortex penetrates the sample to annihilate the antivortex in the slit;the V-Av pair in the slit are driven off and expelled laterally;both the lateral vortex and the slit antivortex are depinned and driven together to annihilation in the halfway.展开更多
基金National Natural Science Foundation ofChina( No.5 98790 12 )
文摘The near crack line analysis method was used to investigate a crack loaded by a pair of point shear forces in an infinite plate in an elastic-perfectly plastic solid. The analytical solution was obtained, that is the elastic-plastic fields near crack line and law that the length of the plastic zone along the crack line is varied with external loads. The results are sufficiently precise near the crack line and are not confined by small scale yielding conditions.
文摘In this paper, the improved near crack line analysis method proposed in Refs. [1] and [2] is used to investigate a center crack loaded by two pairs of antiplane point forces in a finite plate in an elastic-perfectly plastic solid. And the analytical solutions are obtained, that is elastic-plastic stress fields near the crack line and the law that the length of the plastic zone along the crack line is varied with an external loads tr,ld the bearing capacity of a finite plate with a center crack. The results of this paper are sufficiently precise near the crack line, because the assumptions of the small scale yielding theory have not been used and no other assumptions have been taken.
文摘In this paper, an adaptive line spectral pair filter is derived from an adaptive lattice filter. A least-mean-square(LMS) type adaptive algorithm used to calculate directly the line spectral pair(LSP) coefficients on a stage-by-stage basis is presented. Experimental results show that the algorithm has higher convergence rate and lower misadjustment as compared with the other algorithms. The LSP coefficients calculated by the algorithm have been used to carry out speech linear predictive synthesis, resulting in better results than PARCOR coefficients.
基金National Natural Science Foundation of China(Grant No.42076192).
文摘Measuring and reconstructing the shape of workpieces have been considered as a fundamental step in both reverse engineering and product quality control.Owing to increasing structural complexity of recent products,measurements from multiple directions are typically required in current scanning techniques.Specifically,the plane structured light can be applied to measure one area of a part at a time,with an additional algorithm required to merge the collected data of each area.Alternatively,the line structured light sensor integrated on CNC machines or CMMs could also realize multi-view measurement.However,the system needs to be repeatedly calibrated at each new direction.This paper presents a flexible scanning method by integrating laser line sensors with articulated arm coordinate measuring machines(AACMM).Since the output of the laser line sensor is 2D raw data in the laser plane,our system model introduces an explicit transformation from the 2D sensor coordinate frame to the 3D base coordinate frame of the AACMM(i.e.,the translation and rotation the of the 2D sensor coordinate in the sixth coordinate system of AACMM).To solve the model,the“conjugate pairs”are proposed and identified by measuring a fixed point(e.g.,a sphere center).Moreover,a search algorithm is adopted to find the optimal solution,which noticeably boosts the model accuracy.The experimental results show that the error of the system is about 0.2 mm,which is caused by the error of the AACMM,the sensor error and the calibration error.By measuring a complicated part,the proposed system is proved to be flexible and facilitate,with the ability to measure a part expediently from any necessary direction.Furthermore,the proposed calibration method can also be used for robot hand-eye relationship calibration.
文摘The improved near crack line analysis method was used to investigate an eccentric cracked plate loaded by two pairs of anti_plane point forces at the crack surface in an elastic_perfectly plastic solid. The analytical solutions of the elastic_plastic stress fields and displacements near the crack line have been found without the assumptions of the small scale yielding. The law that the length of the plastic zone along the crack line is varied with an external loads and the bearing capacity of an eccentric cracked plate are obtained.
文摘The near crack line analysis method was used to investigate a crack loaded by two pairs of point shear forces in an infinite plate in an elastic-perfectly plastic solid, and the analytical solution was obtained. The solutions include: the unit normal vector of the elastic-plastic boundary near the crack line, the elastic-plastic stress fields near crack line, law that the length of the plastic zone along the crack line is varied with an external loads, and the bearing capacity of an infinite plate with a center crack loaded by two pairs of point shear forces. The results are sufficiently precise near the crack line because the assumptions of the small scale yielding theory have not been made and no other assumption have been taken.
基金Project supported by the Fundamental Research Funds for the Central Universities,China(Grant Nos.310812171011 and G2016KY0305)the National Natural Science Foundation of China(Grant No.11421062)the National Key Project of Magneto-Constrained Fusion Energy Development Program,China(Grant No.2013GB110002)
文摘In the framework of phenomenological time-dependent Ginzburg-Landau（TDGL） formalism,the dynamical properties of vortex-antivortex（V-Av） pair in a superconductor film with a narrow slit was studied.The slit position and length can have a great impact not only on the vortex dynamical behavior but also the current-voltage（Ⅰ-Ⅴ） characteristics of the sample.Kinematic vortex lines can be predominated by the location of the slit.In the range of relatively low applied currents for a constant weak magnetic field,kinematic vortex line appears at right or left side of the slit by turns periodically.We found such single-side kinematic vortex line cannot lead to a jump in the Ⅰ-Ⅴ curve.At higher applied currents the phase-slip lines can be observed at left and right sides of the slit simultaneously.The competition between the vortex created at the lateral edge of the sample and the V-Av pair in the slit will result in three distinctly different scenarios of vortex dynamics depending on slit length：the lateral vortex penetrates the sample to annihilate the antivortex in the slit;the V-Av pair in the slit are driven off and expelled laterally;both the lateral vortex and the slit antivortex are depinned and driven together to annihilation in the halfway.
