Accurate thrust assessment is crucial for characterizing the performance of micro-thrusters.This paper presents a comprehensive evaluation of the thrust generated by a needle-type indium field emission electric propul...Accurate thrust assessment is crucial for characterizing the performance of micro-thrusters.This paper presents a comprehensive evaluation of the thrust generated by a needle-type indium field emission electric propulsion(In-FEEP)micro-thruster using three methods based on a pendulum:direct thrust measurement,indirect plume momentum transfer and beam current diagnostics.The experimental setup utilized capacitive displacement sensors for force detection and a voice coil motor as a feedback actuator,achieving a resolution better than 0.1μN.Key performance factors such as ionization and plume divergence of ejected charged particles were also examined.The study reveals that the high applied voltage induces significant electrostatic interference,becoming the dominant source of error in direct thrust measurements.Beam current diagnostics and indirect plume momentum measurements were conducted simultaneously,showing strong agreement within a deviation of less than 0.2N across the operational thrust range.The results from all three methods are consistent within the error margins,verifying the reliability of the indirect measurement approach and the theoretical thrust model based on the electrical parameters of In-FEEP.展开更多
The Taiji program is focused on achieving space-based gravitational wave detection in the frequency range of 0.1 mHz-1 Hz.To achieve drag-free control,Taiji satellites must be equipped with micro-thrusters that satisf...The Taiji program is focused on achieving space-based gravitational wave detection in the frequency range of 0.1 mHz-1 Hz.To achieve drag-free control,Taiji satellites must be equipped with micro-thrusters that satisfy stringent requirements,including a continuously adjustable thrust,thrust resolution of 0.1μN,thrust noise of 0.1μN·Hz^(-0.5)and response time of less than 100 ms.This paper presents the progress of a variable cold gas micro-thruster being developed for the Taiji program.A series of technologies such as a bidirectional piezoelectric drive,spherical valve core,conical nozzle seal,miniature gas chamber,high thruster integration,combined digital and analogue communication and high-frequency closed-loop thrust control were employed to achieve engineering prototypes of a low-noise and fast-response micro-thruster.Ground performance tests indicate that the micro-thruster achieved a minimum thrust of close to 1.1 nN,a thrust resolution of 0.05μN and a maximum specific impulse of 69.1 s using nitrogen gas as the working fluid.The thrust noise was less than 0.1μN·Hz^(-0.5)in the frequency band of 10 mHz-1 Hz,and the thrust response time was 140 ms.The control parameters were further optimised to achieve a flow response time of 50 ms.The results indicate that the developed micro-thruster essentially met the performance requirements for drag-free control to facilitate space-based gravitational wave detection.展开更多
A dual-phase synergistic enhancement method was adopted to strengthen the Al-Mn-Mg-Sc-Zr alloy fabricated by laser powder bed fusion(LPBF)by leveraging the unique advantages of Er and TiB_(2).Spherical powders of 0.5w...A dual-phase synergistic enhancement method was adopted to strengthen the Al-Mn-Mg-Sc-Zr alloy fabricated by laser powder bed fusion(LPBF)by leveraging the unique advantages of Er and TiB_(2).Spherical powders of 0.5wt%Er-1wt%TiB_(2)/Al-Mn-Mg-Sc-Zr nanocomposite were prepared using vacuum homogenization technique,and the density of samples prepared through the LPBF process reached 99.8%.The strengthening and toughening mechanisms of Er-TiB_(2)were investigated.The results show that Al_(3)Er diffraction peaks are detected by X-ray diffraction analysis,and texture strength decreases according to electron backscatter diffraction results.The added Er and TiB_(2)nano-reinforcing phases act as heterogeneous nucleation sites during the LPBF forming process,hindering grain growth and effectively refining the grains.After incorporating the Er-TiB_(2)dual-phase nano-reinforcing phases,the tensile strength and elongation at break of the LPBF-deposited samples reach 550 MPa and 18.7%,which are 13.4%and 26.4%higher than those of the matrix material,respectively.展开更多
To explore the formation mechanism of anisotropy in Ti-6Al-4V alloy fabricated by selective laser melting(SLM),the compressive mechanical properties,microhardness,microstructure,and crystallographic orientation of the...To explore the formation mechanism of anisotropy in Ti-6Al-4V alloy fabricated by selective laser melting(SLM),the compressive mechanical properties,microhardness,microstructure,and crystallographic orientation of the alloy across different planes were investigated.The anisotropy of SLM-fabricated Ti-6Al-4V alloys was analyzed,and the electron backscatter diffraction technique was used to investigate the influence of different grain types and orientations on the stress-strain distribution at various scales.Results reveal that in room-temperature compression tests at a strain rate of 10^(-3) s^(-1),both the compressive yield strength and microhardness vary along the deposition direction,indicating a certain degree of mechanical property anisotropy.The alloy exhibits a columnar microstructure;along the deposition direction,the grains appear equiaxed,and they have internal hexagonal close-packed(hcp)α/α'martensitic structure.α'phase has a preferential orientation approximately along the<0001>direction.Anisotropy arises from the high aspect ratio of columnar grains,along with the weak texture of the microstructure and low symmetry of the hcp crystal structure.展开更多
Conventional ignition methods are proving to be ineffective for low-sensitivity energetic materials,highlighting the need to investigate alternative ignition systems,such as laser-based techniques.Over the past decade...Conventional ignition methods are proving to be ineffective for low-sensitivity energetic materials,highlighting the need to investigate alternative ignition systems,such as laser-based techniques.Over the past decade,lasers have emerged as a promising solution,providing focused energy beams for controllable,efficient,and reliable ignition in the field of energetic materials.This study presents a comparative analysis of two state-of-the-art ignition approaches:direct laser ignition and laser-driven flyer ignition.Experiments were performed using a Neodymium-doped Yttrium Aluminum Garnet(Nd:YAG)laser at different energy beam levels to systematically evaluate ignition onset.In the direct laser ignition test setup,the laser beam was applied directly to the energetic tested material,while laserdriven flyer ignition utilized 40 and 100μm aluminum foils,propelled at velocities ranging from 300 to 1250 m/s.Comparative analysis with the Lawrence and Trott model substantiated the velocity data and provided insight into the ignition mechanisms.Experimental results indicate that the ignition time for the laser-driven flyer method was significantly shorter,with the pyrotechnic composition achieving complete combustion faster compared to direct laser ignition.Moreover,precise ignition thresholds were determined for both methods,providing critical parameters for optimizing ignition systems in energetic materials.This work elucidates the advantages and limitations of each technique while advancing next-generation ignition technology,enhancing the reliability and safety of propulsion systems.展开更多
The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution an...The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution and short wavelength.Efficient and compact 193 nm DUV laser source thus becomes a hot research area.Currently,193 nm Ar F excimer gas laser is widely employed in DUV lithography systems and serves as the enabling technology for 7 and 5 nm semiconductor fabrication.展开更多
Based on the characteristics of laser-induced surface ignition,energetic photosensitive films show promising potential to meet the ignition requirements of various energetic materials(EMs).In this study,DATNBI/ferric ...Based on the characteristics of laser-induced surface ignition,energetic photosensitive films show promising potential to meet the ignition requirements of various energetic materials(EMs).In this study,DATNBI/ferric alginate(DI/FeA),DI/cobalt alginate(DI/CoA),and DI/nickel alginate(DI/Ni A)films are fabricated by employing sodium alginate(SA)with a three-dimensional network structure as the film matrix,via ionic cross-linking of SA with Fe^(3+),Co^(2+),and Ni^(2+)ions.The study demonstrates that the ionic cross-linking enhances the hydrophobic performance of the films,with the water contact angle increasing from 82.1??to 123.5??.Concurrently,the films'near-infrared(NIR)light absorption improved.Furthermore,transition metal ions facilitate accelerated electron transfer,thereby catalyzing the thermal decomposition of DATNBI.Under 1064 nm laser irradiation,the DI/Fe A film exhibits exceptional combustion performance,with an ignition delay time as low as 76 ms.It successfully acts as an NIR laser ignition medium to initiate the self-sustained combustion of CL-20.This study demonstrates the synergistic realization of enhanced hydrophobicity,improved photosensitivity,and promoted catalytic decomposition through microstructural design of the material,providing new insights for the design of additive-free EMs in laser ignition applications.展开更多
The latest generation of aero engines has set higher standards for thrust-to-weight ratio and energy conversion efficiency,making it imperative to address the challenge of efficiently and accurately machining film coo...The latest generation of aero engines has set higher standards for thrust-to-weight ratio and energy conversion efficiency,making it imperative to address the challenge of efficiently and accurately machining film cooling holes.It has been demonstrated that conventional long-pulse lasers are incapable of meeting the elevated quality surface finish requirements for these holes,a consequence of the severe thermal defects.The employment of backside water-assisted laser drilling technology confers a number of distinct advantages in terms of mitigating laser thermal damage,thus representing a highly promising solution to this challenge.However,significant accumulation of bubbles and machining products during the backside water-assisted laser drilling process has been demonstrated to have a detrimental effect on laser transmission and machining stability,thereby reducing machining quality.In order to surmount these challenges,a novel method has been proposed,namely an ultrasonic shock water flow-assisted picosecond laser drilling technique.Numerical models for ultrasonic acoustic streaming and particle tracking for machining product transport have been established to investigate the mechanism.The simulation results demonstrated that the majority of the machining products could rapidly move away from the machining area because of the action of acoustic streaming,thereby avoiding the accumulation of bubbles and products.Subsequent analysis,comparing the process performance in micro-hole machining,confirmed that the ultrasonic field could effectively eliminate bubble and chip accumulation,thus significantly improving micro-hole quality.Furthermore,the impact of ultrasonic and laser parameters on micro-hole quality under varying machining methods was thoroughly investigated.The findings demonstrated that the novel methodology outlined in this study yielded superior-quality micro-holes at elevated ultrasonic and laser power levels,in conjunction with reduced laser frequency and scanning velocity.The taper of the micro-holes produced by the new method was reduced by more than 25%compared with the other conventional methods.展开更多
A RadioFrequency Quadrupole(RFQ)cooler-buncher system was developed and implemented in a collinear laser spectroscopy setup.This system converts a continuous ion beam into short bunches while enhancing the beam qualit...A RadioFrequency Quadrupole(RFQ)cooler-buncher system was developed and implemented in a collinear laser spectroscopy setup.This system converts a continuous ion beam into short bunches while enhancing the beam quality and reducing the energy spread.The functionality of the RFQ cooler buncher was verified through offline tests with stable rubidium and indium beams delivered from a surface ion source and a laser ablation ion source,respectively.Bunched ion beams with a full width at half maximum of approximately 2μs in the time-of-flight spectrum were successfully achieved with a transmission efficiency exceeding 60%.The implementation of the RFQ cooler-buncher system also significantly improved the overall transmission efficiency of the collinear laser spectroscopy setup.展开更多
Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study el...Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.展开更多
Hollow cathode discharges are widely used as neutralizers for the electric propulsion systems and recently developed into micro-thrusters for the small satellites.In this work,a dualemitter hollow cathode thruster is ...Hollow cathode discharges are widely used as neutralizers for the electric propulsion systems and recently developed into micro-thrusters for the small satellites.In this work,a dualemitter hollow cathode thruster is developed,which can be operated in two different modes—the neutralizer mode and the micro-thruster mode.For characterizing this kind of new device,the Langmuir probe,Faraday probe,and retarding potential analyzer are used to determine the electron temperature,electron density,ion flux,and ion energy distribution function.The operating parameters,including the thrust,and specific impulse,are also measured.A two-dimensional self-consistent extended fluid model is employed to calculate the spatial distribution of plasma parameters and the fluid field of electrons in the region around the emitters.By comparing the diagnostic and modelling results,it is found that the change in the electric field and ionization zone is the essential reason for the different performances of the device in the neutralizer and micro-thruster modes.Variation in the electric field leads to an ion acceleration effect in the micro-thruster mode;moving of the ionization zone raises the plasma pressure in the orifice region of the hollow cathode,and thus leads to enhanced plasma throttling and gas expanding effects.By analyzing the above mechanisms,the possible methods for improving this kind of hollow cathode micro-thruster are discussed.展开更多
Digital micro-thruster arrays can be used for special missions of micro/nano-satellites with the requirements of high precision and small impulse.This paper presents a novel control allocation algorithm for the digita...Digital micro-thruster arrays can be used for special missions of micro/nano-satellites with the requirements of high precision and small impulse.This paper presents a novel control allocation algorithm for the digital micro-thruster array,namely status graph based control allocation(SGBCA)algorithm,which aims at finding the optimal micro thrusters combination scheme to realize the sequential control synthesis for micro/nano-satellite during real-time orbit control tasks.A mathematical model is set up for the control allocation of this multivariate over-actuated system.Through dividing thrusters into disjoint segments by offline calculation and combining segments dynamically online to provide a sequence of the required impulse for the micro/nano-satellite,the time complexity of the control allocation algorithm decreases significantly.All levels of impulse can be generated by the digital micro thruster arrays and the service life of the arrays can be extended using the segment converting strategy proposed in this paper.The simulation indicates that the algorithm can satisfy the requirements of real-time orbit control for micro/nano-satellites.展开更多
The three-dimensional numerical simulation of two-phase plume flow of solid propellant micro-thrusters was developed.Then it was used to investigate the plume interference effect by combining the direct simulation Mon...The three-dimensional numerical simulation of two-phase plume flow of solid propellant micro-thrusters was developed.Then it was used to investigate the plume interference effect by combining the direct simulation Monte Carlo(DSMC) method for multi-component gas flow with the two-way coupling model for two-phase rarefied flow.At different space between the two micro-thrusters and different wall temperature,the plume interference effect was analyzed specifically.The results show that under the plume interference effect the gas is compressed and the flow direction is changed,which resulted in the increasing of gas pressure and temperature;solid phase made no significant effect on the flow parameters of gas phase;with the rising of the space between the two micro-thrusters,the maximum pressure decreased and the maximum temperature increased in the domain under the plume interference effect;the wall temperature could influence the temperature of the gas which is extremely close to the wall,but not the gas pressure.展开更多
In-situ formed high Mn steel coating reinforced by carbides was formed by laser surface alloying(LSA).Laser alloyed layers on 1Cr18Ni9Ti steel with Mn+W_(2)C(specimen A),Mn+NiWC(specimen B)and Mn+SiC(specimen C)powder...In-situ formed high Mn steel coating reinforced by carbides was formed by laser surface alloying(LSA).Laser alloyed layers on 1Cr18Ni9Ti steel with Mn+W_(2)C(specimen A),Mn+NiWC(specimen B)and Mn+SiC(specimen C)powders were fabricated to improve the wear and corrosion behavior of 1Cr18Ni9Ti steel blades in high speed mixers.Microstructure evolution,phases,element distribution,microhardness,wear and corrosion behavior of the laser alloyed layers were investigated.Results indicated that high Mn steel matrix composites with undissolved W_(2)C,WC and other in-situ formed carbides were formed by LSA with Mn+W_(2)C and Mn+NiWC while SiC totally dissolved into the high Mn matrix when adding Mn+SiC.Ni as the binding phase in Ni-WC powder decreased the crack sensitivity of the alloyed layer as compared with the addition of W_(2)C powder.An improvement in average microhardness was achieved in the matrix in specimen A,B and C,with the value of 615,602 and 277 HV_(0.5),while that of the substrate was 212 HV_(0.5).The increase of microhardness,wear and corrosion resistance is highly corelated to microstructure,formed phases,type and content of carbides,micro-hardness and toughness of the alloyed layers.展开更多
Combined pulsed laser(CPL),introduced in 1975 for target damage,integrates different lasers to achieve high peak power and pulse energy.However,despite decades of research,CPL remains unused for long-range target dama...Combined pulsed laser(CPL),introduced in 1975 for target damage,integrates different lasers to achieve high peak power and pulse energy.However,despite decades of research,CPL remains unused for long-range target damage due to the challenge of maintaining high peak power density over long distances.We note that a potential solution lies in leveraging the air filament generated by femtosecond laser,which can transmit peak power densities higher than 1014 W/cm^(2)under the power clamping effect.To address this,a concept of a femtosecond laser induced air filament-CW CPL for surface damage of ceramics was introduced.We found no surface changes in ceramic targets when irradiated with a CW laser alone.By way of contrast,the target can be penetrated in a very short time(20 ms)with the assistance of the femtosecond laser induced air filament.In this context,we employ high-speed shadow imaging,cross-timescale simulation models and macro-microscopic characterization,to elucidate the CPL damage mechanism.The optimal CPL,combining a 1 mJ femtosecond laser and a 500 W CW laser,yields a damage rate of 1.51×10^(7)μm^(3)/J,representing an improvement of approximately 175%compared to single femtosecond laser ablation and around 59%enhancement compared to coating-assisted CW laser ablation.Furthermore,the efficacy of the proposed femtosecond-CW CPL method is demonstrated in causing penetration damage of ceramic/metal composite material or direct damage of sapphire,showcasing its versatility in damaging applications.Consequently,the femtosecond-CW CPL ablation method presented in this paper holds great promise as a new type of damage method for transparent hard and brittle materials.展开更多
Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,a...Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.展开更多
Based on the microstructure characterization,electrochemical impedance spectroscopy,potentiodynamic polarization,and immersion corrosion,this work comparatively analyzed the differences in the electrochemical corrosio...Based on the microstructure characterization,electrochemical impedance spectroscopy,potentiodynamic polarization,and immersion corrosion,this work comparatively analyzed the differences in the electrochemical corrosion morphology and post-foil formation surface morphology of laser beam welded(LBW)sample and spin-formed sample,and compared the corrosion resistance and Cu foil formation ability of two samples in H_(2)SO_(4)/NaCl solution and CuSO_(4) reducing electrolyte.Results show that in H_(2)SO_(4) and NaCl solutions,LBW sample and spin-formed sample exhibit excellent passivation ability and corrosion resistance.Both samples show uniform corrosion morphologies and similar corrosion resistance in the strong acidic solution containing Cl^(-).Meanwhile,the Cu foil formation ability of the welded joint is similar to that of the spin-formed sample,and both samples obtain intact Cu foils with high-quality surfaces and small differences in properties.展开更多
To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0....To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0.27%to 0.22%,enabling the elements Mo and Ti to diffuse fully and to distribute more uniformly,and to forming a substantial number of low-angle grain boundaries.The tensile strength soars from 286±32 MPa to 598±22 MPa,while the elongation increases from 0.08%±0.02%to 0.18%±0.02%,without notable alterations in grain morphology during the tensile deformation.HIP treatment eliminates the molten pool boundaries,which are the primary source for premature failure in LPBFed Mo alloys.Consequently,HIP treatment emerges as a novel and effective approach for strengthening the mechanical properties of LPBFed Mo alloys,offering a fresh perspective on producing high-performance Mo-based alloys.展开更多
Laser additive manufacturing(LAM)has been widely used in high-end manufacturing fields such as aerospace,nuclear power,and shipbuilding.However,it is a grand challenge for direct and continuous observation of complex ...Laser additive manufacturing(LAM)has been widely used in high-end manufacturing fields such as aerospace,nuclear power,and shipbuilding.However,it is a grand challenge for direct and continuous observation of complex laser-matter interaction,melt flow,and defect formation during LAM due to extremely large temperature gradient,fast cooling rate,and small time(millisecond)and space(micron)scales.The emergence of synchrotron radiation provides a feasible approach for in situ observation of the LAM process.This paper outlines the current development in real-time characterization of LAM by synchrotron radiation,including laser-matter interaction,molten pool evolution,solidification structure evolution,and defects formation and elimination.Furthermore,the future development direction and application-oriented research are also discussed.展开更多
A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This pape...A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.展开更多
基金Project supported by the National Key Research and Development Program of China(Grant No.2020YFC2201001)the Guangdong Major Project of Basic and Applied Basic Research(Grant No.2019B030302001)+1 种基金the National Natural Science Foundation of China(Grant Nos.12105373,12105374,and 11927812)the Science and Technology Research Project of Jiangxi Provincial Department of Education(Grant No.GJJ2402105).
文摘Accurate thrust assessment is crucial for characterizing the performance of micro-thrusters.This paper presents a comprehensive evaluation of the thrust generated by a needle-type indium field emission electric propulsion(In-FEEP)micro-thruster using three methods based on a pendulum:direct thrust measurement,indirect plume momentum transfer and beam current diagnostics.The experimental setup utilized capacitive displacement sensors for force detection and a voice coil motor as a feedback actuator,achieving a resolution better than 0.1μN.Key performance factors such as ionization and plume divergence of ejected charged particles were also examined.The study reveals that the high applied voltage induces significant electrostatic interference,becoming the dominant source of error in direct thrust measurements.Beam current diagnostics and indirect plume momentum measurements were conducted simultaneously,showing strong agreement within a deviation of less than 0.2N across the operational thrust range.The results from all three methods are consistent within the error margins,verifying the reliability of the indirect measurement approach and the theoretical thrust model based on the electrical parameters of In-FEEP.
基金the National Key Research and Development Program of China(Nos.2021YFC2202800 and 2021YFC2202604)the Opening Project of the Key Laboratory of Microgravity of the Chinese Academy of Sciences(No.NML202401)+1 种基金the Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2023022)the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDA1502110105)。
文摘The Taiji program is focused on achieving space-based gravitational wave detection in the frequency range of 0.1 mHz-1 Hz.To achieve drag-free control,Taiji satellites must be equipped with micro-thrusters that satisfy stringent requirements,including a continuously adjustable thrust,thrust resolution of 0.1μN,thrust noise of 0.1μN·Hz^(-0.5)and response time of less than 100 ms.This paper presents the progress of a variable cold gas micro-thruster being developed for the Taiji program.A series of technologies such as a bidirectional piezoelectric drive,spherical valve core,conical nozzle seal,miniature gas chamber,high thruster integration,combined digital and analogue communication and high-frequency closed-loop thrust control were employed to achieve engineering prototypes of a low-noise and fast-response micro-thruster.Ground performance tests indicate that the micro-thruster achieved a minimum thrust of close to 1.1 nN,a thrust resolution of 0.05μN and a maximum specific impulse of 69.1 s using nitrogen gas as the working fluid.The thrust noise was less than 0.1μN·Hz^(-0.5)in the frequency band of 10 mHz-1 Hz,and the thrust response time was 140 ms.The control parameters were further optimised to achieve a flow response time of 50 ms.The results indicate that the developed micro-thruster essentially met the performance requirements for drag-free control to facilitate space-based gravitational wave detection.
基金Shaanxi Province Qin Chuangyuan“Scientist+Engineer”Team Construction Project(2022KXJ-071)2022 Qin Chuangyuan Achievement Transformation Incubation Capacity Improvement Project(2022JH-ZHFHTS-0012)+8 种基金Shaanxi Province Key Research and Development Plan-“Two Chains”Integration Key Project-Qin Chuangyuan General Window Industrial Cluster Project(2023QCY-LL-02)Xixian New Area Science and Technology Plan(2022-YXYJ-003,2022-XXCY-010)2024 Scientific Research Project of Shaanxi National Defense Industry Vocational and Technical College(Gfy24-07)Shaanxi Vocational and Technical Education Association 2024 Vocational Education Teaching Reform Research Topic(2024SZX354)National Natural Science Foundation of China(U24A20115)2024 Shaanxi Provincial Education Department Service Local Special Scientific Research Program Project-Industrialization Cultivation Project(24JC005,24JC063)Shaanxi Province“14th Five-Year Plan”Education Science Plan,2024 Project(SGH24Y3181)National Key Research and Development Program of China(2023YFB4606400)Longmen Laboratory Frontier Exploration Topics Project(LMQYTSKT003)。
文摘A dual-phase synergistic enhancement method was adopted to strengthen the Al-Mn-Mg-Sc-Zr alloy fabricated by laser powder bed fusion(LPBF)by leveraging the unique advantages of Er and TiB_(2).Spherical powders of 0.5wt%Er-1wt%TiB_(2)/Al-Mn-Mg-Sc-Zr nanocomposite were prepared using vacuum homogenization technique,and the density of samples prepared through the LPBF process reached 99.8%.The strengthening and toughening mechanisms of Er-TiB_(2)were investigated.The results show that Al_(3)Er diffraction peaks are detected by X-ray diffraction analysis,and texture strength decreases according to electron backscatter diffraction results.The added Er and TiB_(2)nano-reinforcing phases act as heterogeneous nucleation sites during the LPBF forming process,hindering grain growth and effectively refining the grains.After incorporating the Er-TiB_(2)dual-phase nano-reinforcing phases,the tensile strength and elongation at break of the LPBF-deposited samples reach 550 MPa and 18.7%,which are 13.4%and 26.4%higher than those of the matrix material,respectively.
基金National Natural Science Foundation of China(51504138,51674118,52271177)Hunan Provincial Natural Science Foundation of China(2023JJ50181)Supported by State Key Laboratory of Materials Processing and Die&Mould Technology,Huazhong University of Science and Technology(P2024-022)。
文摘To explore the formation mechanism of anisotropy in Ti-6Al-4V alloy fabricated by selective laser melting(SLM),the compressive mechanical properties,microhardness,microstructure,and crystallographic orientation of the alloy across different planes were investigated.The anisotropy of SLM-fabricated Ti-6Al-4V alloys was analyzed,and the electron backscatter diffraction technique was used to investigate the influence of different grain types and orientations on the stress-strain distribution at various scales.Results reveal that in room-temperature compression tests at a strain rate of 10^(-3) s^(-1),both the compressive yield strength and microhardness vary along the deposition direction,indicating a certain degree of mechanical property anisotropy.The alloy exhibits a columnar microstructure;along the deposition direction,the grains appear equiaxed,and they have internal hexagonal close-packed(hcp)α/α'martensitic structure.α'phase has a preferential orientation approximately along the<0001>direction.Anisotropy arises from the high aspect ratio of columnar grains,along with the weak texture of the microstructure and low symmetry of the hcp crystal structure.
文摘Conventional ignition methods are proving to be ineffective for low-sensitivity energetic materials,highlighting the need to investigate alternative ignition systems,such as laser-based techniques.Over the past decade,lasers have emerged as a promising solution,providing focused energy beams for controllable,efficient,and reliable ignition in the field of energetic materials.This study presents a comparative analysis of two state-of-the-art ignition approaches:direct laser ignition and laser-driven flyer ignition.Experiments were performed using a Neodymium-doped Yttrium Aluminum Garnet(Nd:YAG)laser at different energy beam levels to systematically evaluate ignition onset.In the direct laser ignition test setup,the laser beam was applied directly to the energetic tested material,while laserdriven flyer ignition utilized 40 and 100μm aluminum foils,propelled at velocities ranging from 300 to 1250 m/s.Comparative analysis with the Lawrence and Trott model substantiated the velocity data and provided insight into the ignition mechanisms.Experimental results indicate that the ignition time for the laser-driven flyer method was significantly shorter,with the pyrotechnic composition achieving complete combustion faster compared to direct laser ignition.Moreover,precise ignition thresholds were determined for both methods,providing critical parameters for optimizing ignition systems in energetic materials.This work elucidates the advantages and limitations of each technique while advancing next-generation ignition technology,enhancing the reliability and safety of propulsion systems.
基金supported by the National Natural Science Foundation of China(Grant Nos.62450006,62304217,62274157,62127807,62234011,62034008,62074142,62074140)Tianshan Innovation Team Program(Grant No.2022TSYCTD0005)+1 种基金Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB0880000)Youth Innovation Promotion Association of the Chinese Academy of Sciences(Grant Nos.2023124,Y2023032)。
文摘The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution and short wavelength.Efficient and compact 193 nm DUV laser source thus becomes a hot research area.Currently,193 nm Ar F excimer gas laser is widely employed in DUV lithography systems and serves as the enabling technology for 7 and 5 nm semiconductor fabrication.
基金supported by Research Fund of SWUST for PhD(Grant No.22zx7175)Sichuan Science and Technology Program(Grant No.2024NSFSC1097)。
文摘Based on the characteristics of laser-induced surface ignition,energetic photosensitive films show promising potential to meet the ignition requirements of various energetic materials(EMs).In this study,DATNBI/ferric alginate(DI/FeA),DI/cobalt alginate(DI/CoA),and DI/nickel alginate(DI/Ni A)films are fabricated by employing sodium alginate(SA)with a three-dimensional network structure as the film matrix,via ionic cross-linking of SA with Fe^(3+),Co^(2+),and Ni^(2+)ions.The study demonstrates that the ionic cross-linking enhances the hydrophobic performance of the films,with the water contact angle increasing from 82.1??to 123.5??.Concurrently,the films'near-infrared(NIR)light absorption improved.Furthermore,transition metal ions facilitate accelerated electron transfer,thereby catalyzing the thermal decomposition of DATNBI.Under 1064 nm laser irradiation,the DI/Fe A film exhibits exceptional combustion performance,with an ignition delay time as low as 76 ms.It successfully acts as an NIR laser ignition medium to initiate the self-sustained combustion of CL-20.This study demonstrates the synergistic realization of enhanced hydrophobicity,improved photosensitivity,and promoted catalytic decomposition through microstructural design of the material,providing new insights for the design of additive-free EMs in laser ignition applications.
基金supported by the National Natural Science Foundation of China(No.52205468,No.52275431,No.52375186)China Postdoctoral Science Foundation(No.2025M771349)Zhejiang Province Natural Science Foundation(No.LD22E050001)。
文摘The latest generation of aero engines has set higher standards for thrust-to-weight ratio and energy conversion efficiency,making it imperative to address the challenge of efficiently and accurately machining film cooling holes.It has been demonstrated that conventional long-pulse lasers are incapable of meeting the elevated quality surface finish requirements for these holes,a consequence of the severe thermal defects.The employment of backside water-assisted laser drilling technology confers a number of distinct advantages in terms of mitigating laser thermal damage,thus representing a highly promising solution to this challenge.However,significant accumulation of bubbles and machining products during the backside water-assisted laser drilling process has been demonstrated to have a detrimental effect on laser transmission and machining stability,thereby reducing machining quality.In order to surmount these challenges,a novel method has been proposed,namely an ultrasonic shock water flow-assisted picosecond laser drilling technique.Numerical models for ultrasonic acoustic streaming and particle tracking for machining product transport have been established to investigate the mechanism.The simulation results demonstrated that the majority of the machining products could rapidly move away from the machining area because of the action of acoustic streaming,thereby avoiding the accumulation of bubbles and products.Subsequent analysis,comparing the process performance in micro-hole machining,confirmed that the ultrasonic field could effectively eliminate bubble and chip accumulation,thus significantly improving micro-hole quality.Furthermore,the impact of ultrasonic and laser parameters on micro-hole quality under varying machining methods was thoroughly investigated.The findings demonstrated that the novel methodology outlined in this study yielded superior-quality micro-holes at elevated ultrasonic and laser power levels,in conjunction with reduced laser frequency and scanning velocity.The taper of the micro-holes produced by the new method was reduced by more than 25%compared with the other conventional methods.
基金supported by the National Natural Science Foundation of China(Nos.12027809,12350007)National Key R&D Program of China(Nos.2022YFA1605100,2023YFA1606403,and 2023YFE0101600)+1 种基金New Cornerstone Science Foundation through the XPLORER PRIZEfunding from the European Research Council(ERC)under the European Union’s Horizon 2020 research and innovation program under grant agreement No.679038.
文摘A RadioFrequency Quadrupole(RFQ)cooler-buncher system was developed and implemented in a collinear laser spectroscopy setup.This system converts a continuous ion beam into short bunches while enhancing the beam quality and reducing the energy spread.The functionality of the RFQ cooler buncher was verified through offline tests with stable rubidium and indium beams delivered from a surface ion source and a laser ablation ion source,respectively.Bunched ion beams with a full width at half maximum of approximately 2μs in the time-of-flight spectrum were successfully achieved with a transmission efficiency exceeding 60%.The implementation of the RFQ cooler-buncher system also significantly improved the overall transmission efficiency of the collinear laser spectroscopy setup.
基金financial support from NSF ExpandQISE program.The synthesis of tellurene was supported by NSF under grant no.CMMI-2046936supports from Purdue Research Foundation.
文摘Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.
基金supported by the National Natural Science Foundation of China(Nos.61571166,11775063 and 51736003)。
文摘Hollow cathode discharges are widely used as neutralizers for the electric propulsion systems and recently developed into micro-thrusters for the small satellites.In this work,a dualemitter hollow cathode thruster is developed,which can be operated in two different modes—the neutralizer mode and the micro-thruster mode.For characterizing this kind of new device,the Langmuir probe,Faraday probe,and retarding potential analyzer are used to determine the electron temperature,electron density,ion flux,and ion energy distribution function.The operating parameters,including the thrust,and specific impulse,are also measured.A two-dimensional self-consistent extended fluid model is employed to calculate the spatial distribution of plasma parameters and the fluid field of electrons in the region around the emitters.By comparing the diagnostic and modelling results,it is found that the change in the electric field and ionization zone is the essential reason for the different performances of the device in the neutralizer and micro-thruster modes.Variation in the electric field leads to an ion acceleration effect in the micro-thruster mode;moving of the ionization zone raises the plasma pressure in the orifice region of the hollow cathode,and thus leads to enhanced plasma throttling and gas expanding effects.By analyzing the above mechanisms,the possible methods for improving this kind of hollow cathode micro-thruster are discussed.
文摘Digital micro-thruster arrays can be used for special missions of micro/nano-satellites with the requirements of high precision and small impulse.This paper presents a novel control allocation algorithm for the digital micro-thruster array,namely status graph based control allocation(SGBCA)algorithm,which aims at finding the optimal micro thrusters combination scheme to realize the sequential control synthesis for micro/nano-satellite during real-time orbit control tasks.A mathematical model is set up for the control allocation of this multivariate over-actuated system.Through dividing thrusters into disjoint segments by offline calculation and combining segments dynamically online to provide a sequence of the required impulse for the micro/nano-satellite,the time complexity of the control allocation algorithm decreases significantly.All levels of impulse can be generated by the digital micro thruster arrays and the service life of the arrays can be extended using the segment converting strategy proposed in this paper.The simulation indicates that the algorithm can satisfy the requirements of real-time orbit control for micro/nano-satellites.
文摘The three-dimensional numerical simulation of two-phase plume flow of solid propellant micro-thrusters was developed.Then it was used to investigate the plume interference effect by combining the direct simulation Monte Carlo(DSMC) method for multi-component gas flow with the two-way coupling model for two-phase rarefied flow.At different space between the two micro-thrusters and different wall temperature,the plume interference effect was analyzed specifically.The results show that under the plume interference effect the gas is compressed and the flow direction is changed,which resulted in the increasing of gas pressure and temperature;solid phase made no significant effect on the flow parameters of gas phase;with the rising of the space between the two micro-thrusters,the maximum pressure decreased and the maximum temperature increased in the domain under the plume interference effect;the wall temperature could influence the temperature of the gas which is extremely close to the wall,but not the gas pressure.
文摘In-situ formed high Mn steel coating reinforced by carbides was formed by laser surface alloying(LSA).Laser alloyed layers on 1Cr18Ni9Ti steel with Mn+W_(2)C(specimen A),Mn+NiWC(specimen B)and Mn+SiC(specimen C)powders were fabricated to improve the wear and corrosion behavior of 1Cr18Ni9Ti steel blades in high speed mixers.Microstructure evolution,phases,element distribution,microhardness,wear and corrosion behavior of the laser alloyed layers were investigated.Results indicated that high Mn steel matrix composites with undissolved W_(2)C,WC and other in-situ formed carbides were formed by LSA with Mn+W_(2)C and Mn+NiWC while SiC totally dissolved into the high Mn matrix when adding Mn+SiC.Ni as the binding phase in Ni-WC powder decreased the crack sensitivity of the alloyed layer as compared with the addition of W_(2)C powder.An improvement in average microhardness was achieved in the matrix in specimen A,B and C,with the value of 615,602 and 277 HV_(0.5),while that of the substrate was 212 HV_(0.5).The increase of microhardness,wear and corrosion resistance is highly corelated to microstructure,formed phases,type and content of carbides,micro-hardness and toughness of the alloyed layers.
基金supports from National Natural Science Foundation of China(Grant No.52105498)The science and technology innovation Program of Hunan Province(Grant No.2021RC3074)+2 种基金Advanced Laser Technology Laboratory of Anhui Province(AHL2022KF04)National Key R&D Program of China(Grant No.2023YFB14605500)Changsha Natural Science Foundation(kq2402089).
文摘Combined pulsed laser(CPL),introduced in 1975 for target damage,integrates different lasers to achieve high peak power and pulse energy.However,despite decades of research,CPL remains unused for long-range target damage due to the challenge of maintaining high peak power density over long distances.We note that a potential solution lies in leveraging the air filament generated by femtosecond laser,which can transmit peak power densities higher than 1014 W/cm^(2)under the power clamping effect.To address this,a concept of a femtosecond laser induced air filament-CW CPL for surface damage of ceramics was introduced.We found no surface changes in ceramic targets when irradiated with a CW laser alone.By way of contrast,the target can be penetrated in a very short time(20 ms)with the assistance of the femtosecond laser induced air filament.In this context,we employ high-speed shadow imaging,cross-timescale simulation models and macro-microscopic characterization,to elucidate the CPL damage mechanism.The optimal CPL,combining a 1 mJ femtosecond laser and a 500 W CW laser,yields a damage rate of 1.51×10^(7)μm^(3)/J,representing an improvement of approximately 175%compared to single femtosecond laser ablation and around 59%enhancement compared to coating-assisted CW laser ablation.Furthermore,the efficacy of the proposed femtosecond-CW CPL method is demonstrated in causing penetration damage of ceramic/metal composite material or direct damage of sapphire,showcasing its versatility in damaging applications.Consequently,the femtosecond-CW CPL ablation method presented in this paper holds great promise as a new type of damage method for transparent hard and brittle materials.
基金National Natural Science Foundation of China(52071126)Natural Science Foundation of Tianjin City,China(22JCQNJC01240)+2 种基金Central Guidance on Local Science and Technology Development Fund of Hebei Province(226Z1009G)Special Funds for Science and Technology Innovation in Hebei(2022X19)Anhui Provincial Natural Science Foundation(2308085ME135)。
文摘Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.
基金Key Research and Development Program of Shaanxi Province(2022GY-410)Funding of Western Titanium Technologies Co.,Ltd(WX2210)。
文摘Based on the microstructure characterization,electrochemical impedance spectroscopy,potentiodynamic polarization,and immersion corrosion,this work comparatively analyzed the differences in the electrochemical corrosion morphology and post-foil formation surface morphology of laser beam welded(LBW)sample and spin-formed sample,and compared the corrosion resistance and Cu foil formation ability of two samples in H_(2)SO_(4)/NaCl solution and CuSO_(4) reducing electrolyte.Results show that in H_(2)SO_(4) and NaCl solutions,LBW sample and spin-formed sample exhibit excellent passivation ability and corrosion resistance.Both samples show uniform corrosion morphologies and similar corrosion resistance in the strong acidic solution containing Cl^(-).Meanwhile,the Cu foil formation ability of the welded joint is similar to that of the spin-formed sample,and both samples obtain intact Cu foils with high-quality surfaces and small differences in properties.
基金National Natural Science Foundation of China(52105385)Stable Support Plan Program of Shenzhen Natural Science Fund(20220810132537001)+2 种基金Guangdong Basic and Applied Basic Research Foundation(2022A1515010781)Joint Fund of Henan Province Science and Technology R&D Program(225200810002)Fundamental Research Funds of Henan Academy of Sciences(240621041)。
文摘To enhance the mechanical properties of Mo alloys prepared through laser powder bed fusion(LPBF),a hot isostatic pressing(HIP)treatment was used.Results show that following HIP treatment,the porosity decreases from 0.27%to 0.22%,enabling the elements Mo and Ti to diffuse fully and to distribute more uniformly,and to forming a substantial number of low-angle grain boundaries.The tensile strength soars from 286±32 MPa to 598±22 MPa,while the elongation increases from 0.08%±0.02%to 0.18%±0.02%,without notable alterations in grain morphology during the tensile deformation.HIP treatment eliminates the molten pool boundaries,which are the primary source for premature failure in LPBFed Mo alloys.Consequently,HIP treatment emerges as a novel and effective approach for strengthening the mechanical properties of LPBFed Mo alloys,offering a fresh perspective on producing high-performance Mo-based alloys.
基金supported by the National Natural Science Foundation of China-Distinguished Young Scholars(No.52325407)the National Natural Science Foundation of China-Key Program(No.52234010)the Open Research Fund of the State Key Laboratory of Rolling and Automation,Northeastern University(No.2022RALKFKT004).
文摘Laser additive manufacturing(LAM)has been widely used in high-end manufacturing fields such as aerospace,nuclear power,and shipbuilding.However,it is a grand challenge for direct and continuous observation of complex laser-matter interaction,melt flow,and defect formation during LAM due to extremely large temperature gradient,fast cooling rate,and small time(millisecond)and space(micron)scales.The emergence of synchrotron radiation provides a feasible approach for in situ observation of the LAM process.This paper outlines the current development in real-time characterization of LAM by synchrotron radiation,including laser-matter interaction,molten pool evolution,solidification structure evolution,and defects formation and elimination.Furthermore,the future development direction and application-oriented research are also discussed.
文摘A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.
