Lunar base construction is a crucial component of the lunar exploration program,and considering the dynamic characteristics of lunar soil is important for moon construction.Therefore,investigating the dynamic properti...Lunar base construction is a crucial component of the lunar exploration program,and considering the dynamic characteristics of lunar soil is important for moon construction.Therefore,investigating the dynamic properties of lunar soil by establishing a constitutive relationship is critical for providing a theoretical basis for its damage evolution.In this paper,a split Hopkinson pressure bar(SHPB)device was used to perform three sets of impact tests under different pressures on a lunar soil simulant geopolymer(LSSG)with sodium silicate(Na_(2)SiO_(3))contents of 1%,3%,5%and 7%.The dynamic stressestrain curves,failure modes,and energy variation rules of LSSG under different pressures were obtained.The equation was modified based on the ZWT viscoelastic constitutive model and was combined with the damage variable.The damage element obeys the Weibull distribution and the constitutive equation that can describe the mechanical properties of LSSG under dynamic loading was obtained.The results demonstrate that the dynamic compressive strength of LSSG has a marked strain-rate strengthening effect.Na_(2)SiO_(3) has both strengthening and deterioration effects on the dynamic compressive strength of LSSG.As Na_(2)SiO_(3) grows,the dynamic compressive strength of LSSG first increases and then decreases.At a fixed air pressure,5%Na_(2)SiO_(3) had the largest dynamic compressive strength,the largest incident energy,the smallest absorbed energy,and the lightest damage.The ZWT equation was modified according to the stress response properties of LSSG and the range of the SHPB strain rate to obtain the constitutive equation of the LSSG,and the model’s correctness was confirmed.展开更多
By using the widely used JOHNSON-COOK model and the gradient-dependent plasticity to consider microstructural effect beyond the occurrence of shear strain localization,the distributions of local plastic shear strain a...By using the widely used JOHNSON-COOK model and the gradient-dependent plasticity to consider microstructural effect beyond the occurrence of shear strain localization,the distributions of local plastic shear strain and deformation in adiabatic shear band(ASB)were analyzed.The peak local plastic shear strain is proportional to the average plastic shear strain,while it is inversely proportional to the critical plastic shear strain corresponding to the peak flow shear stress.The relative plastic shear deformation between the top and base of ASB depends on the thickness of ASB and the average plastic shear strain.A parametric study was carried out to study the influence of constitutive parameters on shear strain localization.Higher values of static shear strength and work to heat conversion factor lead to lower critical plastic shear strain so that the shear localization is more apparent at the same average plastic shear strain.Higher values of strain-hardening exponent,strain rate sensitive coefficient,melting point,thermal capacity and mass density result in higher critical plastic shear strain,leading to less apparent shear localization at the same average plastic shear strain.The strain rate sensitive coefficient has a minor influence on the critical plastic shear strain,the distributions of local plastic shear strain and deformation in ASB.The effect of strain-hardening modulus on the critical plastic shear strain is not monotonous.When the maximum critical plastic shear strain is reached,the least apparent shear localization occurs.展开更多
The material of nickel aluminum bronze (NAB) presents superior properties such as high strength, excellent wear resistance and stress corrosion resistance and is extensively used for marine propellers. In order to est...The material of nickel aluminum bronze (NAB) presents superior properties such as high strength, excellent wear resistance and stress corrosion resistance and is extensively used for marine propellers. In order to establish the constitutive relation of NAB under high strain rate condition, a new methodology was proposed to accurately identify the constitutive parameters of Johnson?Cook model in machining, combining SHPB tests, predictive cutting force model and orthogonal cutting experiment. Firstly, SHPB tests were carried out to obtain the true stress?strain curves at various temperatures and strain rates. Then, an objective function of the predictive and experimental flow stresses was set up, which put the identified parameters of SHPB tests as the initial value, and utilized the PSO algorithm to identify the constitutive parameters of NAB in machining. Finally, the identified parameters were verified to be sufficiently accurate by comparing the values of cutting forces calculated from the predictive model and FEM simulation.展开更多
The hot deformation behavior of 20 Mn Ni Mo low carbon alloy was investigated by isothermal compression tests over wide ranges of temperature(1223-1523 K) and strain rate(0.01-10 s^(-1)). According to the experimental...The hot deformation behavior of 20 Mn Ni Mo low carbon alloy was investigated by isothermal compression tests over wide ranges of temperature(1223-1523 K) and strain rate(0.01-10 s^(-1)). According to the experimental true stress-true strain data, the constitutive relationships were comparatively studied based on the Arrhenius-type model, Johnson-Cook(JC) model and artificial neural network(ANN), respectively. Furthermore, the predictability of the developed models was evaluated by calculating the correlation coefficient(R) and mean absolute relative error(AARE). The results indicate that the flow stress behavior of 20 Mn NiM o low carbon alloy is significantly influenced by the strain rate and deformation temperature. Compared with the Arrhenius-type model and Johnson-Cook(JC) model, the ANN model is more efficient and has much higher accuracy in describing the flow stress behavior during hot compressing deformation for 20 Mn Ni Mo low carbon alloy.展开更多
Two constitutive models,the modified Johnson-Cook model and the logarithm linear relation model based on empirical approach and data analysis,were presented to illustrate compressive deformation of magnesium alloys AZ...Two constitutive models,the modified Johnson-Cook model and the logarithm linear relation model based on empirical approach and data analysis,were presented to illustrate compressive deformation of magnesium alloys AZ80 under multiple loading directions and strain rates.The results of stress-strain curve analysis and sensitivity index analysis suggested that the stress held large fluctuations in loading direction of 90°.Model testing signified that the logarithm linear relation model was more proper than the modified Johnson-Cook model in view of relative mean square error and correlation coefficients.Moreover,numerical simulation building on established models also indicated that the logarithm linear model is more precise than the modified Johnson-Cook model.展开更多
Strain hardening,strain rate strengthening and thermal softening data of C5191 phosphor bronze at highspeed blanking are not easy to be obtained with a general measure method,therefore,it is quite difficult to establi...Strain hardening,strain rate strengthening and thermal softening data of C5191 phosphor bronze at highspeed blanking are not easy to be obtained with a general measure method,therefore,it is quite difficult to establish the dynamic constitutive model.To solve this problem,the tensile properties at a strain rate of 1 s^(-1) by GLEEBLE-3500,and dynamic tensile conditions at strain rates of 500,1 000 and 1 500 s^(-1) by split Hopkinson tensile bar (SHTB) apparatus are studied.According to these test data,the classic Johnson-Cook equation is modified.Furthermore,the modified Johnson-Cook equation is validated in the physical simulation model of high-speed blanking.The results show that the strength of C5191 phosphor bronze maintains a certain degree of increase as the strain rate increasing and presents a clear sensitivity to strain rate.The modified Johnson-Cook equation,which has better description accuracy than the classical Johnson-Cook equation,can provide important material parameters for physical simulation models of its high-speed blanking process.展开更多
Non-linear numerical modeling, widely used in research and development to understand many complex processes such as forming or machining, does not guarantee the success of a study to be performed. Indeed, the numerica...Non-linear numerical modeling, widely used in research and development to understand many complex processes such as forming or machining, does not guarantee the success of a study to be performed. Indeed, the numerical simulation uses finite element codes where the models already integrated are not based on shapes adjustable to any type of study. In this study, a new form of non-linear constitutive flow law based on the Modified Zerilli-Armstrong model, which can answer the above problem, has been developed to apply it to the numerical simulation of two different tests (a quasi-static compression test, the necking of a circular bar). This flow law is based on the modified Zerilli-Armstrong model, which, together with the new modified Johnson-Cook model, has been compared to appreciate the relevance of the proposal. For that, an implementation of this new law via the VUHARD subroutine into the Abaqus/Explicit finite element code was made to model the two tests. The comparison of the results obtained (from identification) by our proposed law with those obtained using the NMJC shows that this new law better approaches the experiments than the other one. This is also shown through the numerical results using the Abaqus software. It can be said that this way of formulating a flow law allows highlighting the great performance of the proposed approach. Although this law has been only used for quasi-static tests, we can say that it can also be used in dynamic tests.展开更多
文摘Lunar base construction is a crucial component of the lunar exploration program,and considering the dynamic characteristics of lunar soil is important for moon construction.Therefore,investigating the dynamic properties of lunar soil by establishing a constitutive relationship is critical for providing a theoretical basis for its damage evolution.In this paper,a split Hopkinson pressure bar(SHPB)device was used to perform three sets of impact tests under different pressures on a lunar soil simulant geopolymer(LSSG)with sodium silicate(Na_(2)SiO_(3))contents of 1%,3%,5%and 7%.The dynamic stressestrain curves,failure modes,and energy variation rules of LSSG under different pressures were obtained.The equation was modified based on the ZWT viscoelastic constitutive model and was combined with the damage variable.The damage element obeys the Weibull distribution and the constitutive equation that can describe the mechanical properties of LSSG under dynamic loading was obtained.The results demonstrate that the dynamic compressive strength of LSSG has a marked strain-rate strengthening effect.Na_(2)SiO_(3) has both strengthening and deterioration effects on the dynamic compressive strength of LSSG.As Na_(2)SiO_(3) grows,the dynamic compressive strength of LSSG first increases and then decreases.At a fixed air pressure,5%Na_(2)SiO_(3) had the largest dynamic compressive strength,the largest incident energy,the smallest absorbed energy,and the lightest damage.The ZWT equation was modified according to the stress response properties of LSSG and the range of the SHPB strain rate to obtain the constitutive equation of the LSSG,and the model’s correctness was confirmed.
基金Project(2004F052) supported by the Education Department of Liaoning Province,China
文摘By using the widely used JOHNSON-COOK model and the gradient-dependent plasticity to consider microstructural effect beyond the occurrence of shear strain localization,the distributions of local plastic shear strain and deformation in adiabatic shear band(ASB)were analyzed.The peak local plastic shear strain is proportional to the average plastic shear strain,while it is inversely proportional to the critical plastic shear strain corresponding to the peak flow shear stress.The relative plastic shear deformation between the top and base of ASB depends on the thickness of ASB and the average plastic shear strain.A parametric study was carried out to study the influence of constitutive parameters on shear strain localization.Higher values of static shear strength and work to heat conversion factor lead to lower critical plastic shear strain so that the shear localization is more apparent at the same average plastic shear strain.Higher values of strain-hardening exponent,strain rate sensitive coefficient,melting point,thermal capacity and mass density result in higher critical plastic shear strain,leading to less apparent shear localization at the same average plastic shear strain.The strain rate sensitive coefficient has a minor influence on the critical plastic shear strain,the distributions of local plastic shear strain and deformation in ASB.The effect of strain-hardening modulus on the critical plastic shear strain is not monotonous.When the maximum critical plastic shear strain is reached,the least apparent shear localization occurs.
基金Project(2014CB046704)supported by the National Basic Research Program of ChinaProject(2014BAB13B01)supported by the National Science and Technology Pillar Program of China
文摘The material of nickel aluminum bronze (NAB) presents superior properties such as high strength, excellent wear resistance and stress corrosion resistance and is extensively used for marine propellers. In order to establish the constitutive relation of NAB under high strain rate condition, a new methodology was proposed to accurately identify the constitutive parameters of Johnson?Cook model in machining, combining SHPB tests, predictive cutting force model and orthogonal cutting experiment. Firstly, SHPB tests were carried out to obtain the true stress?strain curves at various temperatures and strain rates. Then, an objective function of the predictive and experimental flow stresses was set up, which put the identified parameters of SHPB tests as the initial value, and utilized the PSO algorithm to identify the constitutive parameters of NAB in machining. Finally, the identified parameters were verified to be sufficiently accurate by comparing the values of cutting forces calculated from the predictive model and FEM simulation.
基金Project(CDJZR14130006)supported by the Fundamental Research Funds for the Central Universities,China
文摘The hot deformation behavior of 20 Mn Ni Mo low carbon alloy was investigated by isothermal compression tests over wide ranges of temperature(1223-1523 K) and strain rate(0.01-10 s^(-1)). According to the experimental true stress-true strain data, the constitutive relationships were comparatively studied based on the Arrhenius-type model, Johnson-Cook(JC) model and artificial neural network(ANN), respectively. Furthermore, the predictability of the developed models was evaluated by calculating the correlation coefficient(R) and mean absolute relative error(AARE). The results indicate that the flow stress behavior of 20 Mn NiM o low carbon alloy is significantly influenced by the strain rate and deformation temperature. Compared with the Arrhenius-type model and Johnson-Cook(JC) model, the ANN model is more efficient and has much higher accuracy in describing the flow stress behavior during hot compressing deformation for 20 Mn Ni Mo low carbon alloy.
基金Item Sponsored by National Natural Science Foundation of China(11271339)Plan for Scientific Innovation Talent of Henan Province of China
文摘Two constitutive models,the modified Johnson-Cook model and the logarithm linear relation model based on empirical approach and data analysis,were presented to illustrate compressive deformation of magnesium alloys AZ80 under multiple loading directions and strain rates.The results of stress-strain curve analysis and sensitivity index analysis suggested that the stress held large fluctuations in loading direction of 90°.Model testing signified that the logarithm linear relation model was more proper than the modified Johnson-Cook model in view of relative mean square error and correlation coefficients.Moreover,numerical simulation building on established models also indicated that the logarithm linear model is more precise than the modified Johnson-Cook model.
基金supported by Zhejiang Provincial Natural Science Foundation of China(No.LY18E050005)
文摘Strain hardening,strain rate strengthening and thermal softening data of C5191 phosphor bronze at highspeed blanking are not easy to be obtained with a general measure method,therefore,it is quite difficult to establish the dynamic constitutive model.To solve this problem,the tensile properties at a strain rate of 1 s^(-1) by GLEEBLE-3500,and dynamic tensile conditions at strain rates of 500,1 000 and 1 500 s^(-1) by split Hopkinson tensile bar (SHTB) apparatus are studied.According to these test data,the classic Johnson-Cook equation is modified.Furthermore,the modified Johnson-Cook equation is validated in the physical simulation model of high-speed blanking.The results show that the strength of C5191 phosphor bronze maintains a certain degree of increase as the strain rate increasing and presents a clear sensitivity to strain rate.The modified Johnson-Cook equation,which has better description accuracy than the classical Johnson-Cook equation,can provide important material parameters for physical simulation models of its high-speed blanking process.
文摘Non-linear numerical modeling, widely used in research and development to understand many complex processes such as forming or machining, does not guarantee the success of a study to be performed. Indeed, the numerical simulation uses finite element codes where the models already integrated are not based on shapes adjustable to any type of study. In this study, a new form of non-linear constitutive flow law based on the Modified Zerilli-Armstrong model, which can answer the above problem, has been developed to apply it to the numerical simulation of two different tests (a quasi-static compression test, the necking of a circular bar). This flow law is based on the modified Zerilli-Armstrong model, which, together with the new modified Johnson-Cook model, has been compared to appreciate the relevance of the proposal. For that, an implementation of this new law via the VUHARD subroutine into the Abaqus/Explicit finite element code was made to model the two tests. The comparison of the results obtained (from identification) by our proposed law with those obtained using the NMJC shows that this new law better approaches the experiments than the other one. This is also shown through the numerical results using the Abaqus software. It can be said that this way of formulating a flow law allows highlighting the great performance of the proposed approach. Although this law has been only used for quasi-static tests, we can say that it can also be used in dynamic tests.
