The elevated and room temperature annealing behavior of radiation damage in JFET-input operational amplifiers （op-amps） were investigated. High- and low-dose-rate irradiation results show that one of the JFET-input ...The elevated and room temperature annealing behavior of radiation damage in JFET-input operational amplifiers （op-amps） were investigated. High- and low-dose-rate irradiation results show that one of the JFET-input op-amps studied in this paper exhibits enhanced low-dose-rate sensitivity and the other shows time-dependent effect. The offset voltage of both op-amps increases during long-term annealing at room temperature. However, the offset voltage decreases at elevated temperature. The dramatic difference in annealing behavior at room and elevated temperatures indicates the migration behavior of radiation-induced species at elevated and room temperatures. This provides useful information to understand the degradation and annealing mechanisms in JFET-input op-amps under total ionizing radiation. Moreover, the annealing of oxide trapped charges should be taken into consideration, when using elevated temperature methods to evaluate low-dose-rate damage.展开更多
A versatile current-mode biquadratic filter using three operational amplifiers and nine passive elements is proposed. By suitably choosing the output branch, lowpass, bandpass, highpass, bandstop and allpass transfer ...A versatile current-mode biquadratic filter using three operational amplifiers and nine passive elements is proposed. By suitably choosing the output branch, lowpass, bandpass, highpass, bandstop and allpass transfer functions are realized simultaneously without changing the circuit configuration and elements. Two circuits, one is for low frequency application and the other for high frequency, are proposed. The center frequency, quality factor and gain constants of the circuit can be tuned independently. Simulated results show that the circuits work successfully.展开更多
Symbolic circuit simulator is traditionally applied to the small-signal analysis of analog circuits. This paper establishes a symbolic behavioral macromodeling method applicable to both small-signal and large-signal a...Symbolic circuit simulator is traditionally applied to the small-signal analysis of analog circuits. This paper establishes a symbolic behavioral macromodeling method applicable to both small-signal and large-signal analysis of general two-stage operational amplifiers （op-amps）. The proposed method creates a two-pole parametric macromodel whose parameters are analytical functions of the circuit element parameters generated by a symbolic circuit simulator. A moment matching technique is used in deriving the analytical model parameter. The created parametric behavioral model can be used for op-amps performance simulation in both frequency and time domains. In particular, the parametric models are highly suited for fast statistical simulation of op-amps in the time-domain. Experiment results show that the statistical distributions of the op-amp slew and settling time characterized by the proposed model agree well with the transistor-level results in addition to achieving significant speedup.展开更多
The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent L...The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.展开更多
The problem of chatter vibration is associated with adverse consequences that often lead to tool impairment and poor surface finished in a workpiece, and thus, controlling or suppressing chatter vibrations is of great...The problem of chatter vibration is associated with adverse consequences that often lead to tool impairment and poor surface finished in a workpiece, and thus, controlling or suppressing chatter vibrations is of great significance to improve machining quality. In this paper, a workpiece and an actuator dynamics are considered in modeling and controller design. A proportional-integral controller(PI) is presented to control and actively damp the chatter vibration of a workpiece in the milling process. The controller is chosen on the basis of its highly stable output and a smaller amount of steady-state error. The controller is realized using analog operational amplifier circuit. The work has contributed to planning a novel approach that addresses the problem of chatter vibration in spite of technical hitches in modeling and controller design. The method can also lead to considerable reduction in vibrations and can be beneficial in industries in term of cost reduction and energy saving. The application of this method is verified using active damping device actuator(ADD) in the milling of steel.展开更多
This paper presents a three-stage CMOS operational amplifier （opamp） that combines accuracy with stability for a wide range of capacitive loads. A so-called quenching capacitor is added to a multipath nested Miller ...This paper presents a three-stage CMOS operational amplifier （opamp） that combines accuracy with stability for a wide range of capacitive loads. A so-called quenching capacitor is added to a multipath nested Miller compensation （MNMC） topology to obtain stability for a wide range of capacitive loads. Theoretical analysis and mathematical formulas are provided to prove the improvement in stability. A prototype of this frequency compen- sation scheme is implemented in a 0.7μm CMOS process. Measurement′s show that the amplifier can drive capaci- tive loads ranging from 100pF to 100/μF with a gain of 90dB and a minimum phase margin of 26°. The amplifier has a unity-gain bandwidth of 1MHz for a 100pF capacitive load. It employs a quenching capacitance of 18pF.展开更多
Principles of design are described for the low frequency integrated operationalamplifler XD1531 with low noise. The procedures of design of both the circuit structure and the tran-sistor shape are considered. The firs...Principles of design are described for the low frequency integrated operationalamplifler XD1531 with low noise. The procedures of design of both the circuit structure and the tran-sistor shape are considered. The first stage of the circuit is designed with the methods of low noise atlow frequencies. The measures which decrease noises, especially, the 1/f noise originating .from thesemiconductor surface state and defects, are used for the transistor structure design. With analysisand comparison to products here and abroad in characteristics, it is shown that XD1531 has a lowernoise index at low frequencies than others, and the effectiveness of design methods for bringing lownoises have been demonstrated.展开更多
Today, along with the prevalent use of portable equipment, wireless, and other battery powered systems, the demand for amplifiers with a high gain-bandwidth product（GBW）, slew rate（SR）, and at the same time very l...Today, along with the prevalent use of portable equipment, wireless, and other battery powered systems, the demand for amplifiers with a high gain-bandwidth product（GBW）, slew rate（SR）, and at the same time very low static power dissipation is growing. In this work, an operational transconductance amplifier（OTA） with an enhanced SR is proposed. By inserting a sensing resistor in the input port of the current mirror in the OTA, the voltage drop across the resistor is converted into an output current containing a term in proportion to the square of the voltage, and then the SR of the proposed OTA is significantly enhanced and the current dissipation can be reduced. The proposed OTA is designed and simulated with a 0.5μm complementary metal oxide semiconductor（CMOS） process. The simulation results show that the SR is 4.54V/μs, increased by 8.25 times than that of the conventional design, while the current dissipation is only 87.3%.展开更多
An optimization design technique to obtain global solution for a two-stage operational amplifier(op-amp) with frequency compensation is presented.This frequency compensation technique can adjust the equivalent resista...An optimization design technique to obtain global solution for a two-stage operational amplifier(op-amp) with frequency compensation is presented.This frequency compensation technique can adjust the equivalent resistance to guarantee that the phase margin is stable even though circumstance temperature varies.Geometric programming is used to optimize the component values and transistor dimensions.It is used in this analog integrated circuit design to calculate these parameters automatically.This globally optimal amplifier obtains minimum power while other specifications are fulfilled.展开更多
A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architectu...A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architecture with positive channel metal oxide semiconductor（PMOS） differential input transistors and sub-threshold technology are applied under the low supply voltage.Simulation results show that this amplifier has significantly low power,while maintaining almost the same gain,bandwidth and other key performances.The power required is only 0.12 mW,which is applicable to low-power and low-voltage real-time signal acquisition and processing system.展开更多
We extend the method of searching “eigen-operator” of the square of the Schroedinger operator to the interaction picture, which not only helps to construct Hamiltonians of two kinds of parametric amplifiers but also...We extend the method of searching “eigen-operator” of the square of the Schroedinger operator to the interaction picture, which not only helps to construct Hamiltonians of two kinds of parametric amplifiers but also leads to a new uncertainty relation regarding to the free Hamiltonian and the interacting Hamiltonian.展开更多
This paper presents two schemes of high performance CMOS current mirror, one of them is used for operational tran-sconductance amplifier (OTA) in analog VLSI systems. The linearity, output impedance, bandwidth and acc...This paper presents two schemes of high performance CMOS current mirror, one of them is used for operational tran-sconductance amplifier (OTA) in analog VLSI systems. The linearity, output impedance, bandwidth and accuracy are the most parameters to determine the performance of the current mirror. Here a comparison of two architectures based on same architecture of the amplifier is presented. This comparison includes: linearity, output impedance, bandwidth and accuracy. These two circuits are validated with simulation in technology AMS 0.35 μm. An operational amplifier based on the adapted current mirror is proposed. Its frequency analysis with large bandwidth is validated with the same technology.展开更多
A model of the operational amplifier based on VHDL-AMS is proposed. According to needs of simulating the total ionizing dose(TID) radiation effect, parameters of operational amplifier are taken into account when the p...A model of the operational amplifier based on VHDL-AMS is proposed. According to needs of simulating the total ionizing dose(TID) radiation effect, parameters of operational amplifier are taken into account when the performance is specified. The operational amplifier model used for the TID radiation effect simulation is completed after verifying each modeled parameter. And a parameter for describing the external environment is introduced to make the model combined with TID. Finally, an example is used to illustrate the TID effect on the operational amplifier of MC14573, proving the validity of the model.展开更多
A semiconductor optical amplifier gate based on tensile strained quasi bulk InGaAs is developed.At injection current of 80mA,a 3dB optical bandwidth of more than 85nm is achieved due to dominant band filling effect...A semiconductor optical amplifier gate based on tensile strained quasi bulk InGaAs is developed.At injection current of 80mA,a 3dB optical bandwidth of more than 85nm is achieved due to dominant band filling effect.Moreover,the most important is that very low polarization dependence of gain (<0 7dB),fiber to fiber lossless operation current (70～90mA) and a high extinction ratio (>50dB) are simultaneously obtained over this wide 3dB optical bandwidth (1520～1609nm) which nearly covers the spectral region of the whole C band (1525～1565nm) and the whole L band (1570～1610nm).The gating time is also improved by decreasing carrier lifetime.The wide band polarization insensitive SOA gate is promising for use in future dense wavelength division multiplexing (DWDM) communication systems.展开更多
This paper presents and experimentally verifies an optimized design procedure for a CMOS low noise operational amplifier. The design procedure focuses on the noise performance, which is the key requirement for low noi...This paper presents and experimentally verifies an optimized design procedure for a CMOS low noise operational amplifier. The design procedure focuses on the noise performance, which is the key requirement for low noise operational amplifiers. Based on the noise level and other specifications such as bandwidth, signal swing, slew rate, and power consumption, the device sizes and the biasing conditions are derived. In order to verify the proposed design procedure, a three-stage operational amplifier has been designed. The device parameters obtained from the proposed design procedure closely agree with the simulated results obtained by using HSPICE.展开更多
A novel circuit is presented in order to enhance the slew rate of two-stage operational amplifiers. The enhancer utilizes the class-AB input stage to improve current efficiency, while it works on an open loop with reg...A novel circuit is presented in order to enhance the slew rate of two-stage operational amplifiers. The enhancer utilizes the class-AB input stage to improve current efficiency, while it works on an open loop with regard to the enhanced amplifier so that it has no effect on the stability of the amplifier. During the slewing period, the enhancer detects input differential voltage of the amplifier, and produces external enhancement currents for the amplifier, driving load capacitors to charge/discharge faster. Simulation results show that, fora large input step, the enhancerreduces settling time by nearly 50%. When the circuit is employed in a sample-and-hold circuit, it greatly improves the spur-free dynamic range by 44.6 dB and the total harmonic distortion by 43.9 dB. The proposed circuit is very suitable to operate under a low voltage （1.2 V or below） with a standby current of 200 μA.展开更多
The balanced operational amplifier including its merits and designing methods is discussed by comparing its performance to a conventional differential output amplifier when used in a single balanced stage. A balanced ...The balanced operational amplifier including its merits and designing methods is discussed by comparing its performance to a conventional differential output amplifier when used in a single balanced stage. A balanced OTA circuit design is also presented.展开更多
In the recent decade,different researchers have performed hardware implementation for different applications covering various areas of experts.In this research paper,a novel analog design and implementation of differe...In the recent decade,different researchers have performed hardware implementation for different applications covering various areas of experts.In this research paper,a novel analog design and implementation of different steps of fuzzy systems with current differencing buffered amplifier(CDBA)are proposed with a compact structure that can be used in many signal processing applications.The proposed circuits are capable of wide input current range,simple structure,and are highly linear.Different electrical parameters were compared for the proposed fuzzy system when using different membership functions.The novelty of this paper lies in the electronic implementation of different steps for realizing a fuzzy system using current amplifiers.When the power supply voltage of CDBA is 2V,it results in 155mW,power dissipation;4.615KΩ,input resistance;366KΩ,output resistances;and 189.09 dB,common-mode rejection ratio.A 155.519 dB,voltage gain,and 0.76V/μs,the slew rate is analyzed when the power supply voltage of CDBAis 3V.The fuzzy system is realized in 20nm CMOS technology and investigated with an output signal of high precision and high speed,illustrating that it is suitable for realtime applications.In this research paper,a consequence of feedback resistance on the adder circuit and the defuzzified circuit is also analyzed and the best results are obtained using 100K resistance.The structure has a low hardware complexity leading to a low delay and a rather high quality.展开更多
文摘The elevated and room temperature annealing behavior of radiation damage in JFET-input operational amplifiers （op-amps） were investigated. High- and low-dose-rate irradiation results show that one of the JFET-input op-amps studied in this paper exhibits enhanced low-dose-rate sensitivity and the other shows time-dependent effect. The offset voltage of both op-amps increases during long-term annealing at room temperature. However, the offset voltage decreases at elevated temperature. The dramatic difference in annealing behavior at room and elevated temperatures indicates the migration behavior of radiation-induced species at elevated and room temperatures. This provides useful information to understand the degradation and annealing mechanisms in JFET-input op-amps under total ionizing radiation. Moreover, the annealing of oxide trapped charges should be taken into consideration, when using elevated temperature methods to evaluate low-dose-rate damage.
文摘A versatile current-mode biquadratic filter using three operational amplifiers and nine passive elements is proposed. By suitably choosing the output branch, lowpass, bandpass, highpass, bandstop and allpass transfer functions are realized simultaneously without changing the circuit configuration and elements. Two circuits, one is for low frequency application and the other for high frequency, are proposed. The center frequency, quality factor and gain constants of the circuit can be tuned independently. Simulated results show that the circuits work successfully.
文摘Symbolic circuit simulator is traditionally applied to the small-signal analysis of analog circuits. This paper establishes a symbolic behavioral macromodeling method applicable to both small-signal and large-signal analysis of general two-stage operational amplifiers （op-amps）. The proposed method creates a two-pole parametric macromodel whose parameters are analytical functions of the circuit element parameters generated by a symbolic circuit simulator. A moment matching technique is used in deriving the analytical model parameter. The created parametric behavioral model can be used for op-amps performance simulation in both frequency and time domains. In particular, the parametric models are highly suited for fast statistical simulation of op-amps in the time-domain. Experiment results show that the statistical distributions of the op-amp slew and settling time characterized by the proposed model agree well with the transistor-level results in addition to achieving significant speedup.
文摘The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.
基金supported by National Natural Science Foundation of China(Grant No.51675440)Fundamental Research Funds for the Central Universities of China(Grant no.3102018gxc025)
文摘The problem of chatter vibration is associated with adverse consequences that often lead to tool impairment and poor surface finished in a workpiece, and thus, controlling or suppressing chatter vibrations is of great significance to improve machining quality. In this paper, a workpiece and an actuator dynamics are considered in modeling and controller design. A proportional-integral controller(PI) is presented to control and actively damp the chatter vibration of a workpiece in the milling process. The controller is chosen on the basis of its highly stable output and a smaller amount of steady-state error. The controller is realized using analog operational amplifier circuit. The work has contributed to planning a novel approach that addresses the problem of chatter vibration in spite of technical hitches in modeling and controller design. The method can also lead to considerable reduction in vibrations and can be beneficial in industries in term of cost reduction and energy saving. The application of this method is verified using active damping device actuator(ADD) in the milling of steel.
文摘This paper presents a three-stage CMOS operational amplifier （opamp） that combines accuracy with stability for a wide range of capacitive loads. A so-called quenching capacitor is added to a multipath nested Miller compensation （MNMC） topology to obtain stability for a wide range of capacitive loads. Theoretical analysis and mathematical formulas are provided to prove the improvement in stability. A prototype of this frequency compen- sation scheme is implemented in a 0.7μm CMOS process. Measurement′s show that the amplifier can drive capaci- tive loads ranging from 100pF to 100/μF with a gain of 90dB and a minimum phase margin of 26°. The amplifier has a unity-gain bandwidth of 1MHz for a 100pF capacitive load. It employs a quenching capacitance of 18pF.
文摘Principles of design are described for the low frequency integrated operationalamplifler XD1531 with low noise. The procedures of design of both the circuit structure and the tran-sistor shape are considered. The first stage of the circuit is designed with the methods of low noise atlow frequencies. The measures which decrease noises, especially, the 1/f noise originating .from thesemiconductor surface state and defects, are used for the transistor structure design. With analysisand comparison to products here and abroad in characteristics, it is shown that XD1531 has a lowernoise index at low frequencies than others, and the effectiveness of design methods for bringing lownoises have been demonstrated.
基金supported in part by the National Natural Science Foundation of China under Grant No.61274027the National Key Laboratory of Analog Integrated Circuit under Grant No.9140c90503140c09048
文摘Today, along with the prevalent use of portable equipment, wireless, and other battery powered systems, the demand for amplifiers with a high gain-bandwidth product（GBW）, slew rate（SR）, and at the same time very low static power dissipation is growing. In this work, an operational transconductance amplifier（OTA） with an enhanced SR is proposed. By inserting a sensing resistor in the input port of the current mirror in the OTA, the voltage drop across the resistor is converted into an output current containing a term in proportion to the square of the voltage, and then the SR of the proposed OTA is significantly enhanced and the current dissipation can be reduced. The proposed OTA is designed and simulated with a 0.5μm complementary metal oxide semiconductor（CMOS） process. The simulation results show that the SR is 4.54V/μs, increased by 8.25 times than that of the conventional design, while the current dissipation is only 87.3%.
基金the Shanghai Application Material(AM) Research Foundation (No.08700740700)
文摘An optimization design technique to obtain global solution for a two-stage operational amplifier(op-amp) with frequency compensation is presented.This frequency compensation technique can adjust the equivalent resistance to guarantee that the phase margin is stable even though circumstance temperature varies.Geometric programming is used to optimize the component values and transistor dimensions.It is used in this analog integrated circuit design to calculate these parameters automatically.This globally optimal amplifier obtains minimum power while other specifications are fulfilled.
基金Sponsored by the National Natural Science Foundation of China (60843005)the Basic Research Foundation of Beijing Institute of Technology(20070142018)
文摘A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architecture with positive channel metal oxide semiconductor（PMOS） differential input transistors and sub-threshold technology are applied under the low supply voltage.Simulation results show that this amplifier has significantly low power,while maintaining almost the same gain,bandwidth and other key performances.The power required is only 0.12 mW,which is applicable to low-power and low-voltage real-time signal acquisition and processing system.
基金The project supported by National Natural Science Foundation of China and the Doctoral Tutoring Foundation of the Ministry of Education of Chin
文摘We extend the method of searching “eigen-operator” of the square of the Schroedinger operator to the interaction picture, which not only helps to construct Hamiltonians of two kinds of parametric amplifiers but also leads to a new uncertainty relation regarding to the free Hamiltonian and the interacting Hamiltonian.
文摘This paper presents two schemes of high performance CMOS current mirror, one of them is used for operational tran-sconductance amplifier (OTA) in analog VLSI systems. The linearity, output impedance, bandwidth and accuracy are the most parameters to determine the performance of the current mirror. Here a comparison of two architectures based on same architecture of the amplifier is presented. This comparison includes: linearity, output impedance, bandwidth and accuracy. These two circuits are validated with simulation in technology AMS 0.35 μm. An operational amplifier based on the adapted current mirror is proposed. Its frequency analysis with large bandwidth is validated with the same technology.
基金supported by the National Natural Science Foundation of China (No. 61303034)Aeronautical Science Foundation of China (No. 2013ZD31007)
文摘A model of the operational amplifier based on VHDL-AMS is proposed. According to needs of simulating the total ionizing dose(TID) radiation effect, parameters of operational amplifier are taken into account when the performance is specified. The operational amplifier model used for the TID radiation effect simulation is completed after verifying each modeled parameter. And a parameter for describing the external environment is introduced to make the model combined with TID. Finally, an example is used to illustrate the TID effect on the operational amplifier of MC14573, proving the validity of the model.
文摘A semiconductor optical amplifier gate based on tensile strained quasi bulk InGaAs is developed.At injection current of 80mA,a 3dB optical bandwidth of more than 85nm is achieved due to dominant band filling effect.Moreover,the most important is that very low polarization dependence of gain (<0 7dB),fiber to fiber lossless operation current (70～90mA) and a high extinction ratio (>50dB) are simultaneously obtained over this wide 3dB optical bandwidth (1520～1609nm) which nearly covers the spectral region of the whole C band (1525～1565nm) and the whole L band (1570～1610nm).The gating time is also improved by decreasing carrier lifetime.The wide band polarization insensitive SOA gate is promising for use in future dense wavelength division multiplexing (DWDM) communication systems.
文摘This paper presents and experimentally verifies an optimized design procedure for a CMOS low noise operational amplifier. The design procedure focuses on the noise performance, which is the key requirement for low noise operational amplifiers. Based on the noise level and other specifications such as bandwidth, signal swing, slew rate, and power consumption, the device sizes and the biasing conditions are derived. In order to verify the proposed design procedure, a three-stage operational amplifier has been designed. The device parameters obtained from the proposed design procedure closely agree with the simulated results obtained by using HSPICE.
基金supported by the National Science&Technology Major Project(No.2009ZX03007-002-02)the Program of Shanghai Subject Chief Scientist(No.08XD14007)+1 种基金the Shanghai Municipal IC Design Special Program(No.097062)the Special Research Projects for PhD Education(No.20100071110026)
文摘A novel circuit is presented in order to enhance the slew rate of two-stage operational amplifiers. The enhancer utilizes the class-AB input stage to improve current efficiency, while it works on an open loop with regard to the enhanced amplifier so that it has no effect on the stability of the amplifier. During the slewing period, the enhancer detects input differential voltage of the amplifier, and produces external enhancement currents for the amplifier, driving load capacitors to charge/discharge faster. Simulation results show that, fora large input step, the enhancerreduces settling time by nearly 50%. When the circuit is employed in a sample-and-hold circuit, it greatly improves the spur-free dynamic range by 44.6 dB and the total harmonic distortion by 43.9 dB. The proposed circuit is very suitable to operate under a low voltage （1.2 V or below） with a standby current of 200 μA.
文摘The balanced operational amplifier including its merits and designing methods is discussed by comparing its performance to a conventional differential output amplifier when used in a single balanced stage. A balanced OTA circuit design is also presented.
文摘In the recent decade,different researchers have performed hardware implementation for different applications covering various areas of experts.In this research paper,a novel analog design and implementation of different steps of fuzzy systems with current differencing buffered amplifier(CDBA)are proposed with a compact structure that can be used in many signal processing applications.The proposed circuits are capable of wide input current range,simple structure,and are highly linear.Different electrical parameters were compared for the proposed fuzzy system when using different membership functions.The novelty of this paper lies in the electronic implementation of different steps for realizing a fuzzy system using current amplifiers.When the power supply voltage of CDBA is 2V,it results in 155mW,power dissipation;4.615KΩ,input resistance;366KΩ,output resistances;and 189.09 dB,common-mode rejection ratio.A 155.519 dB,voltage gain,and 0.76V/μs,the slew rate is analyzed when the power supply voltage of CDBAis 3V.The fuzzy system is realized in 20nm CMOS technology and investigated with an output signal of high precision and high speed,illustrating that it is suitable for realtime applications.In this research paper,a consequence of feedback resistance on the adder circuit and the defuzzified circuit is also analyzed and the best results are obtained using 100K resistance.The structure has a low hardware complexity leading to a low delay and a rather high quality.
