Based on the two-pass differential temperature rolling bonding method,the effects of prefabricated steel/aluminum composite panel temperature on interface characteristics and microstructure properties were investigate...Based on the two-pass differential temperature rolling bonding method,the effects of prefabricated steel/aluminum composite panel temperature on interface characteristics and microstructure properties were investigated through experimental analysis and finite element simulations.When the temperature exceeds 400℃,the effective preparation of the steel-aluminum transition joint can be achieved,and with the increase in temperature,the interface shear and pull-off strength of the steel-aluminum transition joint exhibits an initial decrease followed by an increase.Both the interface shear and pull-off fractures are in 1060 aluminum matrix.As the temperature increases,the size of the average grain in 1060 aluminum matrix increases and then decreases.When the temperature reaches 550℃,the comprehensive performance of the prepared steel-aluminum transition joint is the best,with the interface shear strength of 77 MPa and the interface pull-off strength of 153 MPa,exceeding the bonding strength of the explosive compounding method.There are no pinholes,wrinkles,or cracks in the lateral bending matrix and the interface.展开更多
This paper developed a hot Pressing aided exothermic synthesis (HPES) technique. to fabricate NiAl matrix composites containing 0 and 20 v.% TiB_2 particles. The conversion to the product was complete. and TiB_2 parti...This paper developed a hot Pressing aided exothermic synthesis (HPES) technique. to fabricate NiAl matrix composites containing 0 and 20 v.% TiB_2 particles. The conversion to the product was complete. and TiB_2 particles in the matrix were uniformly dispersed. The inter faces between nail and TiB_2 were atomically flat. sharp and free from any inter facial phases in most cases. In some cases. however. thin inter facial amorphous layers existed at NiAl/ TiB_2 interfaces. In addition, the microstructure and inter faces were highly thermal stable. In all processing states. the yield strengths at room temperature or at 1000℃ of the composite were approximately three times as strong as that of the unrein forced NiAl. The ambient fracture toughness of the composite was also superior to monolithic NiAl.展开更多
Calcium sulfate whiskers（CSWs） modified with glutaraldehyde-crosslinked poly（vinyl alcohol）（PVA） or traditional surface modifiers,including silane coupling agent,titanate coupling agent and stearic acid,were use...Calcium sulfate whiskers（CSWs） modified with glutaraldehyde-crosslinked poly（vinyl alcohol）（PVA） or traditional surface modifiers,including silane coupling agent,titanate coupling agent and stearic acid,were used to strengthen poly（vinyl chloride）（PVC）,and the morphologies,mechanical and heat resistant properties of the resulting composites were compared.The results clearly show that glutaraldehyde cross-linked PVA modified CSW/PVC composite（c PVA@CSW/PVC） has the strongest interfacial interaction,good and stable mechanical and heat resistant properties.Nielsen＇s modified Kerner＇s equation for Young＇s modulus is better than other models examined for the CSW/PVC composites.The half debonding angle θ of c PVA@CSW/PVC composite is lower than that of other composites except silane coupling agent modified CSW/PVC composites,indicating a very strong interfacial adhesion between c PVA@CSW and PVC.In general,cross-linked PVA is effective and environmentally friendly in modifying inorganic fillers.展开更多
Currently for the steel tube reinforced concrete composite pile research, although predecessors make a comprehensive research on the composite pile beating performance, design technology, but there are still many prob...Currently for the steel tube reinforced concrete composite pile research, although predecessors make a comprehensive research on the composite pile beating performance, design technology, but there are still many problems have not been solved, such as the steel tube reinforced concrete pile composite interracial force learn performance research is still in the initial stage. In this paper, we mainly discuss the research methods of several interface mechanical properties and propose the possibility of studying the mechanical properties of the steel tube reinforced concrete composite pile by using the principle of ultrasonic speckle.展开更多
Laser fusion brazing welding was proposed.Galvanized steel/AA6061 lapped joint was obtained by laser fusion brazing welding technique using the laser-induced aluminium molten pool spreading and wetting the solid steel...Laser fusion brazing welding was proposed.Galvanized steel/AA6061 lapped joint was obtained by laser fusion brazing welding technique using the laser-induced aluminium molten pool spreading and wetting the solid steel surface.Wide joint interface was formed using the rectangular laser beam coupled with the synchronous powder feeding.The result showed that the tiny structure with the composition of a-Al and Al–Si eutectic was formed in the weld close to the Al side.And close to the steel side,a layer of compact Fe–Al–Si intermetallics,including the Al-rich FeAl3,Fe2Al5 phases and Al–Fe–Si s1 phase,was generated with the thickness of about 10–20 lm.Transverse tensile shows the brittlefractured characteristic along to the seam/steel interface with the maximum yield strength of 152.5 MPa due to the existence of hardening phases s1 and Al–Fe intermetallics.展开更多
In this work, low-carbon steel specimens were subjected to the quenching and partitioning process after being partially or fully austenitized to investigate their microstructural evolution and mechanical properties. A...In this work, low-carbon steel specimens were subjected to the quenching and partitioning process after being partially or fully austenitized to investigate their microstructural evolution and mechanical properties. According to the results of scanning electron microscopy and transmission electron microscopy observations, X-ray diffraction analysis, and tensile tests, upper bainite or tempered martensite appears successively in the microstructure with increasing austenitization temperature or increasing partitioning time. In the partially austenitized specimens, the retained austenite grains are carbon-enriched twice during the heat treatment, which can significantly stabilize the phases at room temperature. Furthermore, after partial austenitization, the specimen exhibits excellent elongation, with a maximum elongation of 37.1%. By contrast, after full austenitization, the specimens exhibit good ultimate tensile strength and high yield strength. In the case of a specimen with a yield strength of 969 MPa, the maximum value of the ultimate tensile strength reaches 1222 MPa. During the partitioning process, carbon partitioning and carbon homogenization within austenite affect interface migration. In addition, the volume fraction and grain size of retained austenite observed in the final microstructure will also be affected.展开更多
Diamond particles reinforced aluminum–silicon matrix composites,abbreviated as Al（Si）/diamond composites,were fabricated by squeeze casting.The effect of Si content on the microstructure and mechanical properties o...Diamond particles reinforced aluminum–silicon matrix composites,abbreviated as Al（Si）/diamond composites,were fabricated by squeeze casting.The effect of Si content on the microstructure and mechanical properties of the composites were investigated.The mechanical properties are found to increase monotonically with Si content increasing up to 7.0 wt%.The Al-7.0 wt% Si/diamond composite exhibits tensile strength of 78 MPa,bending strength of 230 MPa,and compressive strength of426 MPa.Al–Si eutectic phases are shown to connect with Al matrix and diamond particles tightly,which is responsible for the enhancement of mechanical properties in the Al（Si）/diamond composites.展开更多
To investigate the dynamic behavior and energy dissipation of the rock−concrete interface,dynamic splitting tests on bi-material discs were conducted by using the split Hopkinson pressure bar.The test results reveal t...To investigate the dynamic behavior and energy dissipation of the rock−concrete interface,dynamic splitting tests on bi-material discs were conducted by using the split Hopkinson pressure bar.The test results reveal that with the change of the interface inclination angles(θ),the influence of interface groove width on the bearing capacity of specimens also varies.Whenθincreases from 0°to 30°,the bearing capacity of the specimen increases first and then decreases with the rise of the interface groove width;the optimal groove width on the rock surface in this range of interface inclination angles is 5 mm.Whenθincreases from 45°to 90°,the bearing capacity of the specimen has no obvious change.Moreover,whenθincreases from 0°to 45°,the dissipated energy of the specimens rises obviously at first and then tends to be stable as the width of the interface groove increases.展开更多
A simple, economic, efficient and eco-friendly nanodiamond （ND） modifying method to reinforce the ND]epoxy composite for the industrialization of the high-performance ND/epoxy composite is always desired. In the pre...A simple, economic, efficient and eco-friendly nanodiamond （ND） modifying method to reinforce the ND]epoxy composite for the industrialization of the high-performance ND/epoxy composite is always desired. In the present work, the ND was successfully modified only using aqueous ammonia through an easy-to-operate method by replacing the hydrogen atoms in the carboxyl group with ammonium ions. Ammonia, which is the only pollutant in the process, could be recycled. The modified ND/epoxy composite showed an overwhelming advantage over the neat epoxy or the ND/epoxy composite in storage modulus in their glassy state without any degradation of tensile strength, hardness and fracture toughness.展开更多
基金supported by the National Natural Science Foundation of China(52005361)the Central Science and Technology Research Fund(YDZJSX2022A022)+3 种基金the Postdoctoral Science Foundation of China(2021M692373)the State Key Laboratory of Material Processing and Mold Technology of Huazhong University of Science and Technology(P2022-004)the China Postdoctoral Science Foundation Project(2023T160474)Open Research Fund from the Hai'an&Taiyuan University of Technology Advanced Manufacturing and Intelligent Equipment Industrial Research Institute(2023HA-TYUTKFYF019).
文摘Based on the two-pass differential temperature rolling bonding method,the effects of prefabricated steel/aluminum composite panel temperature on interface characteristics and microstructure properties were investigated through experimental analysis and finite element simulations.When the temperature exceeds 400℃,the effective preparation of the steel-aluminum transition joint can be achieved,and with the increase in temperature,the interface shear and pull-off strength of the steel-aluminum transition joint exhibits an initial decrease followed by an increase.Both the interface shear and pull-off fractures are in 1060 aluminum matrix.As the temperature increases,the size of the average grain in 1060 aluminum matrix increases and then decreases.When the temperature reaches 550℃,the comprehensive performance of the prepared steel-aluminum transition joint is the best,with the interface shear strength of 77 MPa and the interface pull-off strength of 153 MPa,exceeding the bonding strength of the explosive compounding method.There are no pinholes,wrinkles,or cracks in the lateral bending matrix and the interface.
文摘This paper developed a hot Pressing aided exothermic synthesis (HPES) technique. to fabricate NiAl matrix composites containing 0 and 20 v.% TiB_2 particles. The conversion to the product was complete. and TiB_2 particles in the matrix were uniformly dispersed. The inter faces between nail and TiB_2 were atomically flat. sharp and free from any inter facial phases in most cases. In some cases. however. thin inter facial amorphous layers existed at NiAl/ TiB_2 interfaces. In addition, the microstructure and inter faces were highly thermal stable. In all processing states. the yield strengths at room temperature or at 1000℃ of the composite were approximately three times as strong as that of the unrein forced NiAl. The ambient fracture toughness of the composite was also superior to monolithic NiAl.
基金financially supported by the National Natural Science Foundation of China(U 1507123)the Foundation from Qinghai Science and Technology Department(2014-HZ-817)Kunlun Scholar Award Program of Qinghai Province
文摘Calcium sulfate whiskers（CSWs） modified with glutaraldehyde-crosslinked poly（vinyl alcohol）（PVA） or traditional surface modifiers,including silane coupling agent,titanate coupling agent and stearic acid,were used to strengthen poly（vinyl chloride）（PVC）,and the morphologies,mechanical and heat resistant properties of the resulting composites were compared.The results clearly show that glutaraldehyde cross-linked PVA modified CSW/PVC composite（c PVA@CSW/PVC） has the strongest interfacial interaction,good and stable mechanical and heat resistant properties.Nielsen＇s modified Kerner＇s equation for Young＇s modulus is better than other models examined for the CSW/PVC composites.The half debonding angle θ of c PVA@CSW/PVC composite is lower than that of other composites except silane coupling agent modified CSW/PVC composites,indicating a very strong interfacial adhesion between c PVA@CSW and PVC.In general,cross-linked PVA is effective and environmentally friendly in modifying inorganic fillers.
文摘Currently for the steel tube reinforced concrete composite pile research, although predecessors make a comprehensive research on the composite pile beating performance, design technology, but there are still many problems have not been solved, such as the steel tube reinforced concrete pile composite interracial force learn performance research is still in the initial stage. In this paper, we mainly discuss the research methods of several interface mechanical properties and propose the possibility of studying the mechanical properties of the steel tube reinforced concrete composite pile by using the principle of ultrasonic speckle.
基金financially supported by the National Natural Science Foundation of China (No.50875005)Beijing Natural Science Foundation (No.3102005)
文摘Laser fusion brazing welding was proposed.Galvanized steel/AA6061 lapped joint was obtained by laser fusion brazing welding technique using the laser-induced aluminium molten pool spreading and wetting the solid steel surface.Wide joint interface was formed using the rectangular laser beam coupled with the synchronous powder feeding.The result showed that the tiny structure with the composition of a-Al and Al–Si eutectic was formed in the weld close to the Al side.And close to the steel side,a layer of compact Fe–Al–Si intermetallics,including the Al-rich FeAl3,Fe2Al5 phases and Al–Fe–Si s1 phase,was generated with the thickness of about 10–20 lm.Transverse tensile shows the brittlefractured characteristic along to the seam/steel interface with the maximum yield strength of 152.5 MPa due to the existence of hardening phases s1 and Al–Fe intermetallics.
基金funded by China Scholarship Council (No. 201406460053)
文摘In this work, low-carbon steel specimens were subjected to the quenching and partitioning process after being partially or fully austenitized to investigate their microstructural evolution and mechanical properties. According to the results of scanning electron microscopy and transmission electron microscopy observations, X-ray diffraction analysis, and tensile tests, upper bainite or tempered martensite appears successively in the microstructure with increasing austenitization temperature or increasing partitioning time. In the partially austenitized specimens, the retained austenite grains are carbon-enriched twice during the heat treatment, which can significantly stabilize the phases at room temperature. Furthermore, after partial austenitization, the specimen exhibits excellent elongation, with a maximum elongation of 37.1%. By contrast, after full austenitization, the specimens exhibit good ultimate tensile strength and high yield strength. In the case of a specimen with a yield strength of 969 MPa, the maximum value of the ultimate tensile strength reaches 1222 MPa. During the partitioning process, carbon partitioning and carbon homogenization within austenite affect interface migration. In addition, the volume fraction and grain size of retained austenite observed in the final microstructure will also be affected.
基金financially supported by the National Natural Science Foundation of China (No.51271017)the Fundamental Research Funds for the Central Universities (No.FRFTP-13-033A)the Program for New Century Excellent Talents in University (No.NCET-10-0227)
文摘Diamond particles reinforced aluminum–silicon matrix composites,abbreviated as Al（Si）/diamond composites,were fabricated by squeeze casting.The effect of Si content on the microstructure and mechanical properties of the composites were investigated.The mechanical properties are found to increase monotonically with Si content increasing up to 7.0 wt%.The Al-7.0 wt% Si/diamond composite exhibits tensile strength of 78 MPa,bending strength of 230 MPa,and compressive strength of426 MPa.Al–Si eutectic phases are shown to connect with Al matrix and diamond particles tightly,which is responsible for the enhancement of mechanical properties in the Al（Si）/diamond composites.
基金supported by the National Natural Science Foundation of China (No.41772313)the National Natural Science Foundation for Young Scientists of China (No.52104111)+3 种基金the Hunan Science and Technology Planning Project,China (No.2019RS3001)the Natural Science Foundation of Hunan Province,China (No.2021JJ30819)Key Science and Technology Project of Guangxi Transportation Industry (Research on fine blasting and disaster control technology of mountain expressway tunnel),Chinathe financial contribution and convey their appreciation for supporting this basic research。
文摘To investigate the dynamic behavior and energy dissipation of the rock−concrete interface,dynamic splitting tests on bi-material discs were conducted by using the split Hopkinson pressure bar.The test results reveal that with the change of the interface inclination angles(θ),the influence of interface groove width on the bearing capacity of specimens also varies.Whenθincreases from 0°to 30°,the bearing capacity of the specimen increases first and then decreases with the rise of the interface groove width;the optimal groove width on the rock surface in this range of interface inclination angles is 5 mm.Whenθincreases from 45°to 90°,the bearing capacity of the specimen has no obvious change.Moreover,whenθincreases from 0°to 45°,the dissipated energy of the specimens rises obviously at first and then tends to be stable as the width of the interface groove increases.
基金supported by the National Natural Science Foundation of China(Nos.21503241,21473223,51221264,21261160487,91545119 and 91545110)the CAS/SAFEA International Partnership Program for Creative Research Teams
文摘A simple, economic, efficient and eco-friendly nanodiamond （ND） modifying method to reinforce the ND]epoxy composite for the industrialization of the high-performance ND/epoxy composite is always desired. In the present work, the ND was successfully modified only using aqueous ammonia through an easy-to-operate method by replacing the hydrogen atoms in the carboxyl group with ammonium ions. Ammonia, which is the only pollutant in the process, could be recycled. The modified ND/epoxy composite showed an overwhelming advantage over the neat epoxy or the ND/epoxy composite in storage modulus in their glassy state without any degradation of tensile strength, hardness and fracture toughness.
