As the development of new power systems progresses,the inherent inertia of power systems continues to diminish.Centralized frequency regulation,which relies on rapid communication and real-time control,can enable inve...As the development of new power systems progresses,the inherent inertia of power systems continues to diminish.Centralized frequency regulation,which relies on rapid communication and real-time control,can enable inverter-based thermostatically controlled load(ITCL)clusters to provide virtual inertia support to the power grid.However,ITCL clusters exhibit significant discrete response characteristics,which precludes the direct integration of load-side inertia support into the synchronous unit side.To address this issue,this paper elaborates on the existing technical framework and analyzes the underlying causes of the problem.It proposes a timestamp allocation mechanism for ITCL cluster control instructions,ensuring that many ITCL terminals can be triggered at staggered times,thereby allowing the load cluster power to adhere to the inertia analog control law at any moment.Building on this foundation,the paper further examines the impact of the inertia response delay of ITCL clusters,which is based on centralized frequency regulation,on the stability of the power system.A design scheme for inertia analog control parameters is proposed,taking into account dual constraints,frequency stability and load cluster regulation capacity.Finally,the feasibility and applicability of the proposed mechanism and parameter design scheme are investigated through simulations conducted via MATLAB/Simulink.展开更多
The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more...The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more fluctuations of system inertia.To address this issue,a novel equivalent inertia evaluation method for multiple PV power generation under virtual inertia control is proposed.The total system inertia is first estimated based on historical or injected disturbance.Then,the total inertia of multiple PV power generation is directly calculated by subtracting the inertia of synchronous generators from the estimated system inertia.To improve practicality,a partition-based strategy is introduced,which divides the system into regions characterized by homogeneous frequency response behaviors.After partitioning,only the synchronous generator data within the region and inter-area transmission line power are required for evaluation,reducing the demand for PMU data compared to traditional methods requiring measurements at each PV connection point.Comprehensive simulation results in a 10-machine 39-bus system penetrated with multiple PV power generation validated the effectiveness of the proposed method.展开更多
Sensorless control of switched reluctance motors(SRMs) often requires a hybrid mode combining low-speed pulse injection methods and high-speed model-based estimation.However,pulse injection causes unwanted audible noi...Sensorless control of switched reluctance motors(SRMs) often requires a hybrid mode combining low-speed pulse injection methods and high-speed model-based estimation.However,pulse injection causes unwanted audible noises and torque ripples.This article proposes an enhanced model-based sensorless approach to extend downwards the speed range in which sensorless control can work without injection.An inertial phase-locked loop (IPLL) based on a stator flux observer is introduced for position estimation.Compared to the conventional phase-locked loop scheme,the IPLL offers a more robust disturbance rejection capability and thus reduces the flux model errors at lower speeds.Experimental results substantiate the feasibility of the extended low-speed operation using the model-based sensorless control approach.展开更多
In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.T...In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.The control accuracy of ISP is fundamentally circumscribed by various disturbance torques in rotating shaft.Therefore,a dynamic model of ISP incorporating composite perturbations is established with regard to the stabilization of axis in the inertial reference frame.Subsequently,an online estimator for control loop uncertainties based on the sliding mode control algorithm is designed to estimate the aggregate disturbances of various parameters uncertainties and other unmodeled disturbances that cannot be accurately calibrated.Finally,the proposed DSMO is integrated into a classical proportional-integral-derivative(PID)control scheme,utilizing feedforward approach to compensate the composite disturbance in the control loop online.The effectiveness of the proposed disturbance observer is validated through simulation and hardware experimentation,demonstrating a significant improvement in the dynamic control performance and robustness of the classical PID controller extensively utilized in the field of engineering.展开更多
In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to ...In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to obtain the maximal positive definite solution of nonlinear matrix equation X+A^(*)X|^(-α)A=Q with the case 0<α≤1.Based on this method,a new iterative algorithm is developed,and its convergence proof is given.Finally,two numerical examples are provided to show the effectiveness of the proposed method.展开更多
In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regiona...In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regional controllability is more adapted to systems described by dynamic systems.Regional controllability results in a strategic area were established for vibrating plates by the Hilbertian Uniqueness Method.展开更多
The ambitious global targets on decarbonization present the need for massive integration of renewable generation in power systems,resulting in a significant decrease in the system inertia.In addition to the reduction ...The ambitious global targets on decarbonization present the need for massive integration of renewable generation in power systems,resulting in a significant decrease in the system inertia.In addition to the reduction in system inertia,the transmission system in Great Britain(GB)faces some unique challenges owing to its relatively small capacity,while being decoupled from other transmission systems and with the renewable resources largely non-uniformly distributed across the system.This paper presents opinions and insights on the challenges associated with frequency control in a low-inertia system and the potential solutions from a GB perspective.In this paper,we focus on three main techniques that act over different time scales:synchronous condensers,inertia emulation,and fast frequency response.We evaluate their relative advantages and limitations with learnings from recent research and development projects in GB,along with the opinions on their roles in addressing the frequency control challenges in future low-inertia systems.展开更多
The large inertia of a traditional power system slows down system's frequency response but also allows decent time for controlling the system.Since an autonomous renewable microgrid usually has much smaller inerti...The large inertia of a traditional power system slows down system's frequency response but also allows decent time for controlling the system.Since an autonomous renewable microgrid usually has much smaller inertia,the control system must be very fast and accurate to fight against the small inertia and uncertainties.To reduce the demanding requirements on control,this paper proposes to increase the inertia of photovoltaic(PV) system through inertia emulation.The inertia emulation is realized by controlling the charging/discharging of the direct current(DC)-link capacitor over a certain range and adjusting the PV generation when it is feasible and/or necessary.By well designing the inertia,the DC-link capacitor parameters and the control range,the negative impact of inertia emulation on energy efficiency can be reduced.The proposed algorithm can be integrated with distributed generation setting algorithms to improve dynamic performance and lower implementation requirements.Simulation studies demonstrate the effectiveness of the proposed solution.展开更多
This paper is devoted to adaptive attitude tracking control for rigid spacecraft in the presence of parametric uncertainties, actuator faults and external disturbance. Specifically, a dynamic model is established base...This paper is devoted to adaptive attitude tracking control for rigid spacecraft in the presence of parametric uncertainties, actuator faults and external disturbance. Specifically, a dynamic model is established based on one-tank spacecraft, which explicitly takes into account changing Center of Mass(CM). Then, a control scheme is proposed to achieve attitude tracking.Benefiting from explicitly considering the changing CM during the controller design process, the proposed scheme possesses good robustness to parametric uncertainties with less fuel consumption.Moreover, a fault-tolerant control algorithm is proposed to accommodate actuator faults with no need of knowing the actuators' fault information. Lyapunov-based analysis is provided and the closed-loop system stability is rigorously proved. Finally, numerical simulations are presented to illustrate the effectiveness of the proposed controllers.展开更多
Based on the pressure regulation circuit adopting electro-hydraulic proportional relief valve to control tension, a new type of electro-hydraulic compound control circuit with throttle control unit is presented, which...Based on the pressure regulation circuit adopting electro-hydraulic proportional relief valve to control tension, a new type of electro-hydraulic compound control circuit with throttle control unit is presented, which can obtain optimal dynamic damping ratio through real-time altering pressure-flow gain of the throttle control unit, improve the dynamic characteristic of tension follow-up control for the tension system with high inertia loads. Moreover, the characteristic when the cable linear velocity variation causes change of tension is investigated, and a compound control strategy is proposed. The theoretical analysis and experimental results show that the electro-hydraulic compound control circuit is effective and the characteristic of the compound control strategy is satisfactory.展开更多
The optical storage microgrid system composed of power electronic converters is a small inertia system.Load switching and power supply intermittent will affect the stability of the direct current(DC)bus voltage.Aiming...The optical storage microgrid system composed of power electronic converters is a small inertia system.Load switching and power supply intermittent will affect the stability of the direct current(DC)bus voltage.Aiming at this problem,a virtual inertia optimal control strategy applied to optical storage microgrid is proposed.Firstly,a small signal model of the system is established to theoretically analyze the influence of virtual inertia and damping coefficient on DC bus voltage and to obtain the constraint range of virtual inertia and damping coefficient;Secondly,aiming at the defect that the Sailfish optimization algorithm is easy to premature maturity,a Sailfish optimization algorithm based on the leak-proof net and the cross-mutation propagation mechanism is proposed;Finally,the virtual inertia and damping coefficient of the system are optimized by the improved Sailfish algorithm to obtain the best control parameters.The simulation results in Matlab/Simulink show that the virtual inertia control optimized by the improved Sailfish algorithm improves the system inertia as well as the dynamic response and robustness of the DC bus voltage.展开更多
This paper studies the leader-following attitude coordination problems of multiple spacecraft in the presence of inertia parameter uncertainties. To achieve attitude coordination in the situation that even the leader&...This paper studies the leader-following attitude coordination problems of multiple spacecraft in the presence of inertia parameter uncertainties. To achieve attitude coordination in the situation that even the leader's attitude is only applicable to a part of the following spacecraft, a nonlinear attitude observer is proposed to obtain an accurate estimation of the leader's attitude and angular velocity for all the followers. In addition, a distributed control scheme based on noncertainty equivalence principle is presented for multiple spacecraft' attitude synchronization. With a dynamic scaling, attitude consensus can be achieved asymptotically without any information of the bounds of the uncertain inertia parameters. Furthermore, once the estimations of inertia parameters reach their ideal values, the estimation process will stop and the ideal value of inertia parameter will be held. This is a special advantage of parameter estimation method based on non-certainty equivalence. Numerical simulations are presented to demonstrate that the proposed non-certainty equivalence-based method requires smaller control toque and converges faster compared with the certainty equivalence-based method.展开更多
A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of contro...A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of controlling the po- sition and attitude of both the satellite base and the payload grasped by the manipulator end effectors. The equations of motion in reduced-order form for the constrained system are derived by incorporating the constraint equations in terms of accelerations into Kane＇s equations of the unconstrained system. Model analysis shows that the resulting equations perfectly meet the requirement of adaptive controller design. Consequently, by using an indirect approach, an adaptive control scheme is proposed to accomplish position/attitude trajectory tracking control with the uncertain parameters be- ing estimated on-line. The actuator redundancy due to the closed-loop constraints is utilized to minimize a weighted norm of the joint torques. Global asymptotic stability is proven by using Lyapunov＇s method, and simulation results are also presented to demonstrate the effectiveness of the proposed approach.展开更多
System frequency must be kept very close to its nominal range to ensure the stability of an electric power grid.Excessive system frequency variations are able to result in load shedding,frequency instability,and even ...System frequency must be kept very close to its nominal range to ensure the stability of an electric power grid.Excessive system frequency variations are able to result in load shedding,frequency instability,and even generator damage.With increasing wind power penetration,there is rising concern about the reduction in inertia response and primary frequency control in the electric power grid.Converter-based wind generation is capable of providing inertia response and primary frequency response;nevertheless,the primary frequency and inertia responses of wind generation are different from those of conventional synchronous fleets;it is not completely understood how the primary frequency and inertia responses affect the given system under various disturbances and available kinetic energy levels.Simulations are used to investigate the influences of inertia and droop control strategies on the dynamic frequency responses,particularly the index of the second frequency drop under various disturbance and wind conditions.A quantitative analysis provides insight into setting of inertia and droop control coefficients for various wind and disturbance conditions to facilitate adequate dynamic frequency responses during frequency events.展开更多
Power electronic-interfaced renewable energy sources(RES)exhibit lower inertia compared to traditional synchronous generators.The large-scale integration of RES has led to a significant reduction in system inertia,pos...Power electronic-interfaced renewable energy sources(RES)exhibit lower inertia compared to traditional synchronous generators.The large-scale integration of RES has led to a significant reduction in system inertia,posing significant challenges for maintaining frequency stability in future power systems.This issue has garnered considerable attention in recent years.However,the existing research has not yet achieved a comprehensive understanding of system inertia and frequency stability in the context of low-inertia systems.To this end,this paper provides a comprehensive review of the definition,modeling,analysis,evaluation,and control for frequency stability.It commences with an exploration of inertia and frequency characteristics in low-inertia systems,followed by a novel definition of frequency stability.A summary of frequency stability modeling,analysis,and evaluation methods is then provided,along with their respective applicability in various scenarios.Additionally,the two critical factors of frequency control—energy sources at the system level and control strategies at the device level—are examined.Finally,an outlook on future research in low-inertia power systems is discussed.展开更多
To achieve excellent tracking accuracy,a coarse-fine dual-stage control system is chosen for inertially stabilized platform.The coarse stage is a conventional inertially stabilized platform,and the fine stage is a sec...To achieve excellent tracking accuracy,a coarse-fine dual-stage control system is chosen for inertially stabilized platform.The coarse stage is a conventional inertially stabilized platform,and the fine stage is a secondary servo mechanism to control lens motion in the imaging optical path.Firstly,the dual-stage dynamics is mathematically modeled as a coupling multi-input multi-output(MIMO)control system.Then,by incorporating compensation of adaptive model to deal with parameter variations and nonlinearity,a systematic robust H∞control scheme is designed,which can achieve good tracking performance,as well as improve system robustness against model uncertainties.Lyapunov stability analysis confirmed the stability of the overall control system.Finally,simulation and experiment results are provided to demonstrate the feasibility and effectiveness of the proposed control design method.展开更多
Roll-isolation is an effective way for spinning vehicle to greatly reduce the roll gyro range of strapdown Inertial Navigation System(SINS)and increase the accuracy of inertial navigation.However,during a recent fligh...Roll-isolation is an effective way for spinning vehicle to greatly reduce the roll gyro range of strapdown Inertial Navigation System(SINS)and increase the accuracy of inertial navigation.However,during a recent flight test,the roll-isolated control system failure was observed under a large pitch angle(706 h 685),which introduces a sharply increase in the roll angular velocity,the saturation of roll gyro and the inertial navigation failure.To address this issue,the governing equation of the roll-isolated system is derived with the consideration of various disturbance factors.The control failure is reproduced by numerical simulation.And the results show that the pitch and yaw angular velocity can cause a dramatic increase in roll rate under the large pitch angle,resulting in the roll-isolated control failure.Meanwhile,an improved roll-isolated control system is developed using PI controller,which is verified by mathematical simulation.展开更多
In this paper, the relative sliding motion between the target and the manipulator’s endeffector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the...In this paper, the relative sliding motion between the target and the manipulator’s endeffector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameterexplicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target postcapture operation.展开更多
The performance of vehicle suspension is evaluated based on three conflicting indexes:body acceleration,suspension deflection,and dynamic tire load,which vary across different frequency bands.The suspension control st...The performance of vehicle suspension is evaluated based on three conflicting indexes:body acceleration,suspension deflection,and dynamic tire load,which vary across different frequency bands.The suspension control strategy faces the challenge to strike a balance among these indexes.This research analyzes the fundamental mechanism of control phase deviation effects on skyhook damper control,groundhook damper control,and acceleration drive damper control.From the perspective of complex domain mechanical impedance with the support of the inertial suspension,a structure-based compensation approach is proposed to address for the control phase deviation.The simulation analysis demonstrates that the coordination of inertial suspension structure and control strategy can effectively enhance the comprehensive suspension performance across entire frequency range.Finally,a semi-active inertial suspension bench is implemented.The experimental results indicate that the suspension with the semi-active inertial suspension has outstanding vibration isolation ability,and enhances the suspension performance at ride comfort,suspension deflection,and road friendly significantly.展开更多
The new energy power generation is becoming increasingly important in the power system.Such as photovoltaic power generation has become a research hotspot,however,due to the characteristics of light radiation changes,...The new energy power generation is becoming increasingly important in the power system.Such as photovoltaic power generation has become a research hotspot,however,due to the characteristics of light radiation changes,photovoltaic power generation is unstable and random,resulting in a low utilization rate and directly affecting the stability of the power grid.To solve this problem,this paper proposes a coordinated control strategy for a newenergy power generation system with a hybrid energy storage unit based on the lithium iron phosphate-supercapacitor hybrid energy storage unit.Firstly,the variational mode decomposition algorithm is used to separate the high and low frequencies of the power signal,which is conducive to the rapid and accurate suppression of the power fluctuation of the energy storage system.Secondly,the fuzzy control algorithm is introduced to balance the power between energy storage.In this paper,the actual data is used for simulation,and the simulation results show that the strategy realizes the effective suppression of the bus voltage fluctuation and the accurate control of the internal state of the energy storage unit,effectively avoiding problems such as overshoot and over-discharge,and can significantly improve the stability of the photovoltaic power generation systemand the stability of the Direct Current bus.It is of great significance to promote the development of collaborative control technology for photovoltaic hybrid energy storage units.展开更多
基金supported by the Key Scientific and Technological Projects(2024KJGG27)of Tianfu Yongxing Laboratorythe Experimental Platform Open Innovation Funding(209042025003)of Sichuan Energy Internet Research Institute,Tsinghua University.
文摘As the development of new power systems progresses,the inherent inertia of power systems continues to diminish.Centralized frequency regulation,which relies on rapid communication and real-time control,can enable inverter-based thermostatically controlled load(ITCL)clusters to provide virtual inertia support to the power grid.However,ITCL clusters exhibit significant discrete response characteristics,which precludes the direct integration of load-side inertia support into the synchronous unit side.To address this issue,this paper elaborates on the existing technical framework and analyzes the underlying causes of the problem.It proposes a timestamp allocation mechanism for ITCL cluster control instructions,ensuring that many ITCL terminals can be triggered at staggered times,thereby allowing the load cluster power to adhere to the inertia analog control law at any moment.Building on this foundation,the paper further examines the impact of the inertia response delay of ITCL clusters,which is based on centralized frequency regulation,on the stability of the power system.A design scheme for inertia analog control parameters is proposed,taking into account dual constraints,frequency stability and load cluster regulation capacity.Finally,the feasibility and applicability of the proposed mechanism and parameter design scheme are investigated through simulations conducted via MATLAB/Simulink.
基金supported by the science and technology project of State Grid Ningxia Electric Power Co.,Ltd.(5229DK23000C)the project of Ningxia Natural Science Foundation 2024AAC03745(B329DK24000S).
文摘The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more fluctuations of system inertia.To address this issue,a novel equivalent inertia evaluation method for multiple PV power generation under virtual inertia control is proposed.The total system inertia is first estimated based on historical or injected disturbance.Then,the total inertia of multiple PV power generation is directly calculated by subtracting the inertia of synchronous generators from the estimated system inertia.To improve practicality,a partition-based strategy is introduced,which divides the system into regions characterized by homogeneous frequency response behaviors.After partitioning,only the synchronous generator data within the region and inter-area transmission line power are required for evaluation,reducing the demand for PMU data compared to traditional methods requiring measurements at each PV connection point.Comprehensive simulation results in a 10-machine 39-bus system penetrated with multiple PV power generation validated the effectiveness of the proposed method.
基金supported in part by the National Natural Science Foundation of China 52307069in part by 2024 Tertiary Education Scientific Research Project of Guangzhou Municipal Education Bureau under Grant2024312176in part by the Project of Hetao Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone under Grant HZQB-KCZYB-2020083。
文摘Sensorless control of switched reluctance motors(SRMs) often requires a hybrid mode combining low-speed pulse injection methods and high-speed model-based estimation.However,pulse injection causes unwanted audible noises and torque ripples.This article proposes an enhanced model-based sensorless approach to extend downwards the speed range in which sensorless control can work without injection.An inertial phase-locked loop (IPLL) based on a stator flux observer is introduced for position estimation.Compared to the conventional phase-locked loop scheme,the IPLL offers a more robust disturbance rejection capability and thus reduces the flux model errors at lower speeds.Experimental results substantiate the feasibility of the extended low-speed operation using the model-based sensorless control approach.
基金supported by the National Natural Science Foundation of China(61803015).
文摘In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.The control accuracy of ISP is fundamentally circumscribed by various disturbance torques in rotating shaft.Therefore,a dynamic model of ISP incorporating composite perturbations is established with regard to the stabilization of axis in the inertial reference frame.Subsequently,an online estimator for control loop uncertainties based on the sliding mode control algorithm is designed to estimate the aggregate disturbances of various parameters uncertainties and other unmodeled disturbances that cannot be accurately calibrated.Finally,the proposed DSMO is integrated into a classical proportional-integral-derivative(PID)control scheme,utilizing feedforward approach to compensate the composite disturbance in the control loop online.The effectiveness of the proposed disturbance observer is validated through simulation and hardware experimentation,demonstrating a significant improvement in the dynamic control performance and robustness of the classical PID controller extensively utilized in the field of engineering.
基金Supported in part by Natural Science Foundation of Guangxi(2023GXNSFAA026246)in part by the Central Government's Guide to Local Science and Technology Development Fund(GuikeZY23055044)in part by the National Natural Science Foundation of China(62363003)。
文摘In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to obtain the maximal positive definite solution of nonlinear matrix equation X+A^(*)X|^(-α)A=Q with the case 0<α≤1.Based on this method,a new iterative algorithm is developed,and its convergence proof is given.Finally,two numerical examples are provided to show the effectiveness of the proposed method.
文摘In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regional controllability is more adapted to systems described by dynamic systems.Regional controllability results in a strategic area were established for vibrating plates by the Hilbertian Uniqueness Method.
文摘The ambitious global targets on decarbonization present the need for massive integration of renewable generation in power systems,resulting in a significant decrease in the system inertia.In addition to the reduction in system inertia,the transmission system in Great Britain(GB)faces some unique challenges owing to its relatively small capacity,while being decoupled from other transmission systems and with the renewable resources largely non-uniformly distributed across the system.This paper presents opinions and insights on the challenges associated with frequency control in a low-inertia system and the potential solutions from a GB perspective.In this paper,we focus on three main techniques that act over different time scales:synchronous condensers,inertia emulation,and fast frequency response.We evaluate their relative advantages and limitations with learnings from recent research and development projects in GB,along with the opinions on their roles in addressing the frequency control challenges in future low-inertia systems.
文摘The large inertia of a traditional power system slows down system's frequency response but also allows decent time for controlling the system.Since an autonomous renewable microgrid usually has much smaller inertia,the control system must be very fast and accurate to fight against the small inertia and uncertainties.To reduce the demanding requirements on control,this paper proposes to increase the inertia of photovoltaic(PV) system through inertia emulation.The inertia emulation is realized by controlling the charging/discharging of the direct current(DC)-link capacitor over a certain range and adjusting the PV generation when it is feasible and/or necessary.By well designing the inertia,the DC-link capacitor parameters and the control range,the negative impact of inertia emulation on energy efficiency can be reduced.The proposed algorithm can be integrated with distributed generation setting algorithms to improve dynamic performance and lower implementation requirements.Simulation studies demonstrate the effectiveness of the proposed solution.
基金supported partially by the National Natural Science Foundation of China(Nos.61522301,61633003)
文摘This paper is devoted to adaptive attitude tracking control for rigid spacecraft in the presence of parametric uncertainties, actuator faults and external disturbance. Specifically, a dynamic model is established based on one-tank spacecraft, which explicitly takes into account changing Center of Mass(CM). Then, a control scheme is proposed to achieve attitude tracking.Benefiting from explicitly considering the changing CM during the controller design process, the proposed scheme possesses good robustness to parametric uncertainties with less fuel consumption.Moreover, a fault-tolerant control algorithm is proposed to accommodate actuator faults with no need of knowing the actuators' fault information. Lyapunov-based analysis is provided and the closed-loop system stability is rigorously proved. Finally, numerical simulations are presented to illustrate the effectiveness of the proposed controllers.
基金This project is supported by National Natural Science Foundation of China (No.50475105).
文摘Based on the pressure regulation circuit adopting electro-hydraulic proportional relief valve to control tension, a new type of electro-hydraulic compound control circuit with throttle control unit is presented, which can obtain optimal dynamic damping ratio through real-time altering pressure-flow gain of the throttle control unit, improve the dynamic characteristic of tension follow-up control for the tension system with high inertia loads. Moreover, the characteristic when the cable linear velocity variation causes change of tension is investigated, and a compound control strategy is proposed. The theoretical analysis and experimental results show that the electro-hydraulic compound control circuit is effective and the characteristic of the compound control strategy is satisfactory.
基金the National Natural Science Foundation of China(52177184)。
文摘The optical storage microgrid system composed of power electronic converters is a small inertia system.Load switching and power supply intermittent will affect the stability of the direct current(DC)bus voltage.Aiming at this problem,a virtual inertia optimal control strategy applied to optical storage microgrid is proposed.Firstly,a small signal model of the system is established to theoretically analyze the influence of virtual inertia and damping coefficient on DC bus voltage and to obtain the constraint range of virtual inertia and damping coefficient;Secondly,aiming at the defect that the Sailfish optimization algorithm is easy to premature maturity,a Sailfish optimization algorithm based on the leak-proof net and the cross-mutation propagation mechanism is proposed;Finally,the virtual inertia and damping coefficient of the system are optimized by the improved Sailfish algorithm to obtain the best control parameters.The simulation results in Matlab/Simulink show that the virtual inertia control optimized by the improved Sailfish algorithm improves the system inertia as well as the dynamic response and robustness of the DC bus voltage.
基金supported by the National Natural Science Foundation of China(Nos.11402200,11502203)
文摘This paper studies the leader-following attitude coordination problems of multiple spacecraft in the presence of inertia parameter uncertainties. To achieve attitude coordination in the situation that even the leader's attitude is only applicable to a part of the following spacecraft, a nonlinear attitude observer is proposed to obtain an accurate estimation of the leader's attitude and angular velocity for all the followers. In addition, a distributed control scheme based on noncertainty equivalence principle is presented for multiple spacecraft' attitude synchronization. With a dynamic scaling, attitude consensus can be achieved asymptotically without any information of the bounds of the uncertain inertia parameters. Furthermore, once the estimations of inertia parameters reach their ideal values, the estimation process will stop and the ideal value of inertia parameter will be held. This is a special advantage of parameter estimation method based on non-certainty equivalence. Numerical simulations are presented to demonstrate that the proposed non-certainty equivalence-based method requires smaller control toque and converges faster compared with the certainty equivalence-based method.
基金supported by the National Natural Science Foundation of China(11272027)
文摘A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of controlling the po- sition and attitude of both the satellite base and the payload grasped by the manipulator end effectors. The equations of motion in reduced-order form for the constrained system are derived by incorporating the constraint equations in terms of accelerations into Kane＇s equations of the unconstrained system. Model analysis shows that the resulting equations perfectly meet the requirement of adaptive controller design. Consequently, by using an indirect approach, an adaptive control scheme is proposed to accomplish position/attitude trajectory tracking control with the uncertain parameters be- ing estimated on-line. The actuator redundancy due to the closed-loop constraints is utilized to minimize a weighted norm of the joint torques. Global asymptotic stability is proven by using Lyapunov＇s method, and simulation results are also presented to demonstrate the effectiveness of the proposed approach.
基金This work was supported by the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(20KJB470026)Key Project of Smart Grid Technology and Equipment of National Key Research and Development Plan of China(2016YFB0900601).
文摘System frequency must be kept very close to its nominal range to ensure the stability of an electric power grid.Excessive system frequency variations are able to result in load shedding,frequency instability,and even generator damage.With increasing wind power penetration,there is rising concern about the reduction in inertia response and primary frequency control in the electric power grid.Converter-based wind generation is capable of providing inertia response and primary frequency response;nevertheless,the primary frequency and inertia responses of wind generation are different from those of conventional synchronous fleets;it is not completely understood how the primary frequency and inertia responses affect the given system under various disturbances and available kinetic energy levels.Simulations are used to investigate the influences of inertia and droop control strategies on the dynamic frequency responses,particularly the index of the second frequency drop under various disturbance and wind conditions.A quantitative analysis provides insight into setting of inertia and droop control coefficients for various wind and disturbance conditions to facilitate adequate dynamic frequency responses during frequency events.
基金supported by the National Natural Science Foundation of China(U2166601)。
文摘Power electronic-interfaced renewable energy sources(RES)exhibit lower inertia compared to traditional synchronous generators.The large-scale integration of RES has led to a significant reduction in system inertia,posing significant challenges for maintaining frequency stability in future power systems.This issue has garnered considerable attention in recent years.However,the existing research has not yet achieved a comprehensive understanding of system inertia and frequency stability in the context of low-inertia systems.To this end,this paper provides a comprehensive review of the definition,modeling,analysis,evaluation,and control for frequency stability.It commences with an exploration of inertia and frequency characteristics in low-inertia systems,followed by a novel definition of frequency stability.A summary of frequency stability modeling,analysis,and evaluation methods is then provided,along with their respective applicability in various scenarios.Additionally,the two critical factors of frequency control—energy sources at the system level and control strategies at the device level—are examined.Finally,an outlook on future research in low-inertia power systems is discussed.
基金Project (61174203) supported by the National Natural Science Foundation of China
文摘To achieve excellent tracking accuracy,a coarse-fine dual-stage control system is chosen for inertially stabilized platform.The coarse stage is a conventional inertially stabilized platform,and the fine stage is a secondary servo mechanism to control lens motion in the imaging optical path.Firstly,the dual-stage dynamics is mathematically modeled as a coupling multi-input multi-output(MIMO)control system.Then,by incorporating compensation of adaptive model to deal with parameter variations and nonlinearity,a systematic robust H∞control scheme is designed,which can achieve good tracking performance,as well as improve system robustness against model uncertainties.Lyapunov stability analysis confirmed the stability of the overall control system.Finally,simulation and experiment results are provided to demonstrate the feasibility and effectiveness of the proposed control design method.
基金co-supported by the National Science Foundation of China(No.11532002)Science Challenge Project of China(No.TZ2018001)。
文摘Roll-isolation is an effective way for spinning vehicle to greatly reduce the roll gyro range of strapdown Inertial Navigation System(SINS)and increase the accuracy of inertial navigation.However,during a recent flight test,the roll-isolated control system failure was observed under a large pitch angle(706 h 685),which introduces a sharply increase in the roll angular velocity,the saturation of roll gyro and the inertial navigation failure.To address this issue,the governing equation of the roll-isolated system is derived with the consideration of various disturbance factors.The control failure is reproduced by numerical simulation.And the results show that the pitch and yaw angular velocity can cause a dramatic increase in roll rate under the large pitch angle,resulting in the roll-isolated control failure.Meanwhile,an improved roll-isolated control system is developed using PI controller,which is verified by mathematical simulation.
基金supported by the National Natural Science Foundation of China (Nos. 11972182,U1637207)sponsored by Qing Lan Project, Funded by Science and Technology on Space Intelligent Control Laboratory (No. HTKJ2019KL502012)Funded Project of Shanghai Aerospace Science and Technology (No. SAST2017-092)。
文摘In this paper, the relative sliding motion between the target and the manipulator’s endeffector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameterexplicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target postcapture operation.
基金supported by the National Natural Science Foundation of China(Grant No.52202471)the National Natural Science Foundation of China:Regional Innovation and Development Joint Fund(Grant No.U20A20331)+2 种基金Jiangsu Funding Program for Excellent Postdoctoral Talent(Grant No.2022ZB659)the National Natural Science Foundation of China(Grant No.52002156 and 52072157)the Postgraduate Education Reform Project of Jiangsu Province(Grant No.KYCX21_3333).
文摘The performance of vehicle suspension is evaluated based on three conflicting indexes:body acceleration,suspension deflection,and dynamic tire load,which vary across different frequency bands.The suspension control strategy faces the challenge to strike a balance among these indexes.This research analyzes the fundamental mechanism of control phase deviation effects on skyhook damper control,groundhook damper control,and acceleration drive damper control.From the perspective of complex domain mechanical impedance with the support of the inertial suspension,a structure-based compensation approach is proposed to address for the control phase deviation.The simulation analysis demonstrates that the coordination of inertial suspension structure and control strategy can effectively enhance the comprehensive suspension performance across entire frequency range.Finally,a semi-active inertial suspension bench is implemented.The experimental results indicate that the suspension with the semi-active inertial suspension has outstanding vibration isolation ability,and enhances the suspension performance at ride comfort,suspension deflection,and road friendly significantly.
基金supported by the State Grid Corporation of China Science and Technology Project,grant number 52270723000900K.
文摘The new energy power generation is becoming increasingly important in the power system.Such as photovoltaic power generation has become a research hotspot,however,due to the characteristics of light radiation changes,photovoltaic power generation is unstable and random,resulting in a low utilization rate and directly affecting the stability of the power grid.To solve this problem,this paper proposes a coordinated control strategy for a newenergy power generation system with a hybrid energy storage unit based on the lithium iron phosphate-supercapacitor hybrid energy storage unit.Firstly,the variational mode decomposition algorithm is used to separate the high and low frequencies of the power signal,which is conducive to the rapid and accurate suppression of the power fluctuation of the energy storage system.Secondly,the fuzzy control algorithm is introduced to balance the power between energy storage.In this paper,the actual data is used for simulation,and the simulation results show that the strategy realizes the effective suppression of the bus voltage fluctuation and the accurate control of the internal state of the energy storage unit,effectively avoiding problems such as overshoot and over-discharge,and can significantly improve the stability of the photovoltaic power generation systemand the stability of the Direct Current bus.It is of great significance to promote the development of collaborative control technology for photovoltaic hybrid energy storage units.
