The purpose of this study is to investigate the effect of using Bicarbonate and Calcium parameters as alternatives to the lithostratigraphic units covered the catchment area, on water quality index (WQI) values that h...The purpose of this study is to investigate the effect of using Bicarbonate and Calcium parameters as alternatives to the lithostratigraphic units covered the catchment area, on water quality index (WQI) values that have been implemented with GIS technique at Wadi Al-Arab Dam. The analyzed results (by WQI method) have been used to depict water quality for the two approaches. Based on physico-chemical parameters, the calculated values for WQI over the 3-year for study period were 169, 168, and 157, respectively. While the WQI values were 184, 183 and 172, respectively, as a result of incorporated Bicarbonate and Calcium parameters in WQI calculations that significantly contributed to increasing the WQI. The elevated values may be attributed to the influence of carbonate stone dissolution and mechanical erosion under weathering conditions that are prevalent during winter season in the catchment area. As a consequence of lithostratigraphic unites product and GIS technique integration and normalization processes, most of water quality ranks are good and only autumn season has poor water quality in the 2012 and 2013, while in 2014 it has good water quality in the same season. The WQI values increase in general trend from winter to autumn seasons during the study period that may be referred to outflow by daily consumption, evaporation rising, and seepage water. The analysis shows that the modified water quality values of the Wadi Al-Arab Dam Reservoir (WADR) vary after using Bicarbonate and Calcium parameters by constant value. Generally, the results signify that the WADR is not polluted based on the physical and chemical characteristics of water.展开更多
To categorize the nations to reflect the development status, to date, there are many conceptual frameworks. The Human Development index (HDI) that is published by the United Nations Development Programme is widely acc...To categorize the nations to reflect the development status, to date, there are many conceptual frameworks. The Human Development index (HDI) that is published by the United Nations Development Programme is widely accepted and practiced by many people such as academicians, politicians, and donor organizations. However, though the development of HDI has gone through many revisions since its formulation in 1990, even the current version of the index formulation published in 2016 needs research to better understand and to gap-fill the knowledge base that can enhance the index formulation to facilitate the direction of attention such as release of funds. Therefore, in this paper, based on principal component analysis and K-means clustering algorithm, the data that reflect the measures of life expectancy index (LEI), education index (EI), and income index (II) are analyzed to categorize and to rank the member states of the UN using R statistical software package, an open source extensible programming language for statistical computing and graphics. The outcome of the study shows that the proportion of total eigen value (i.e., proportion of total variance) explained by PCA-1 (i.e., first principal component) accounts for more than 85% of the total variation. Moreover, the proportion of total eigen value explained by PCA-1 increases with time (i.e., yearly) though the amount of increase with time is not significant. However, the proportions of total eigen value explained by PCA-2 and PCA-3 decrease with time. Therefore, the loss of information in choosing PCA-1 to represent the chosen explanatory variables (i.e., LEI, EI, and II) may diminish with time if the trend of increasing pattern of proportion of total eigen value explained by PCA-1 with time continues in the future as well. On the other hand, the correlation between EI and PCA-1 increases with time although the magnitude of increase is not that significant. This same trend is observed in II as well. However, in contrast to these observations, the correlation between PCA-1 and LEI decreases with time. These findings imply that the contributions of EI and II to PCA-1 increase with time, but the contribution of LEI to PCA-1 decreases with time. On top of these, as per Hopkins statistic, the clusterability of the information conveyed by PCA-1 alone is far better than the clusterability of the information conveyed by PCA scores (i.e., PCA-1, PCA-2, and PCA-3) and the explanatory variables. Therefore, choosing PCA-1 to represent the chosen explanatory variables is becoming more concrete.展开更多
In this paper, three rock types including Sandstone, Mudstone, and Crystalline Gypsum were part of a laboratory study conducted to develop a dataset for predicting the unconfined compressive strength of UAE intact sed...In this paper, three rock types including Sandstone, Mudstone, and Crystalline Gypsum were part of a laboratory study conducted to develop a dataset for predicting the unconfined compressive strength of UAE intact sedimentary rock specimens. Four hundred nineteen rock samples from various areas along the coastal region of the UAE were collected and tested for the development of this dataset and evaluation of models. From the statistical analysis of the data, regression equations were established among rock parameters and correlations were expressed and compared by the ones proposed in literature.展开更多
Based on the productivity equation of coalbed methane (CBM) well, considering the impact of coal reservoir reformability on gas well productivity, the main production layer optimization index in the “three-step metho...Based on the productivity equation of coalbed methane (CBM) well, considering the impact of coal reservoir reformability on gas well productivity, the main production layer optimization index in the “three-step method” of optimal combination of production layers is corrected, and then the CBM production layer potential index is introduced to evaluate favorable areas for commingled multi-coal seam production. Through analysis of the key parameters of coal reservoirs affecting the CBM productivity index, a development unit division method for areas with multi-coal seams is established, and a quantitative grading index system is proposed. On this basis, the evaluation process of CBM development favorable area is developed: the mature 3-D modeling technology is used to characterize the reservoir physical properties of multi-coal seams in full-scale;the production layer potential index of each grid is calculated, and the production layer potential index contour under single-layer or commingled multi-layer production are plotted;according to the distribution of the contour of production layer potential index, the quantitative index of CBM development unit is adopted to outline the grade I, II, III coal reservoir distribution areas, and thus to pick out the favorable development areas. The practical application in the Yuwang block of Laochang in Yunnan proved that the favorable area evaluation process proposed can effectively overcome the defects of selecting favorable development areas only relying on evaluation results of a major coal seam pay, and enhance the accuracy of the evaluation results, meeting the requirements of selecting favorable areas for multi-coal seam commingled CBM production.展开更多
Data Envelopment Analysis (DEA) is becoming an increasingly popular tool for assessing the relative performance of industries and companies. By applying DEA theory to the non-financial sector, the relative efficiency ...Data Envelopment Analysis (DEA) is becoming an increasingly popular tool for assessing the relative performance of industries and companies. By applying DEA theory to the non-financial sector, the relative efficiency of 27 listed corporations in the United Arab Emirates (UAE) has been analyzed in this paper. The focus of the study has been on the impact of the financial crisis and the recovery thereafter. Further, the productivity change was decomposed into technical efficiency change and technological change by using the non-parametric Malmquist Productivity Index (MPI) over the period from 2007 to 2014. Based on Malmquist analysis, we find that the most efficient industries during the post-crisis period were food and beverages, telecommunication and pharmaceuticals. In contrast, the sectors that were adversely affected by the crisis were services, real estate, construction and cements. The break-up of the TFP indicated that the efficiency indices in the top performing industries were driven by technological improvements or frontier effects. The top-performing companies in the UAE during the 2007-14 period demonstrated innovation-led growth, aided by the use of better technology, investments in capital equipment, and adoption of new production processes.展开更多
In this paper, the following results are proved: (1) Using both deletion strategy and lock strategy, resolution is complete for a clause set where literals with the same predicate or proposition symbol have the same i...In this paper, the following results are proved: (1) Using both deletion strategy and lock strategy, resolution is complete for a clause set where literals with the same predicate or proposition symbol have the same index. (2) Using deletion strategy, both positive unit lock resolution and input lock resolution are complete for a Horn set where the indexes of positive literals are greater than those of negative literals. (3) Using deletion strategy, input half-lock resolution is complete for a Horn set. Keywords Resolution - index strategy - deletion strategy - unit resolution - input resolution Xiaochun Cheng had his Ph.D in 1996. He has been working as a lecturer at The University of Reading since 2000. He is a vip professor at North East Normal University and at Beijing Normal University. His research interests include theoretical and applied aspects on decision support systems, knowledge-based systems, intelligent systems.展开更多
The previous sensitivity analysis researches are not accurate enough and also have the limited reference value, because those mathematical models are relatively simple and the change of the load and the initial displa...The previous sensitivity analysis researches are not accurate enough and also have the limited reference value, because those mathematical models are relatively simple and the change of the load and the initial displacement changes of the piston are ignored, even experiment verification is not conducted. Therefore, in view of deficiencies above, a nonlinear mathematical model is established in this paper, including dynamic characteristics of servo valve, nonlinear characteristics of pressure-flow, initial displacement of servo cylinder piston and friction nonlinearity. The transfer function block diagram is built for the hydraulic drive unit closed loop position control, as well as the state equations. Through deriving the time-varying coefficient items matrix and time-varying free items matrix of sensitivity equations respectively, the expression of sensitivity equations based on the nonlinear mathematical model are obtained. According to structure parameters of hydraulic drive unit, working parameters, fluid transmission characteristics and measured friction-velocity curves, the simulation analysis of hydraulic drive unit is completed on the MATLAB/Simulink simulation platform with the displacement step 2 mm, 5 mm and 10 mm, respectively. The simulation results indicate that the developed nonlinear mathematical model is sufficient by comparing the characteristic curves of experimental step response and simulation step response under different constant load. Then, the sensitivity function time-history curves of seventeen parameters are obtained, basing on each state vector time-history curve of step response characteristic. The maximum value of displacement variation percentage and the sum of displacement variation absolute values in the sampling time are both taken as sensitivity indexes. The sensitivity indexes values above are calculated and shown visually in histograms under different working conditions, and change rules are analyzed. Then the sensitivity indexes values of four measurable parameters, such as supply pressure, proportional gain, initial position of servo cylinder piston and load force, are verified experimentally on test platform of hydraulic drive unit, and the experimental research shows that the sensitivity analysis results obtained through simulation are approximate to the test results. This research indicates each parameter sensitivity characteristics of hydraulic drive unit, the performance-affected main parameters and secondary parameters are got under different working conditions, which will provide the theoretical foundation for the control compensation and structure optimization of hydraulic drive unit.展开更多
文摘The purpose of this study is to investigate the effect of using Bicarbonate and Calcium parameters as alternatives to the lithostratigraphic units covered the catchment area, on water quality index (WQI) values that have been implemented with GIS technique at Wadi Al-Arab Dam. The analyzed results (by WQI method) have been used to depict water quality for the two approaches. Based on physico-chemical parameters, the calculated values for WQI over the 3-year for study period were 169, 168, and 157, respectively. While the WQI values were 184, 183 and 172, respectively, as a result of incorporated Bicarbonate and Calcium parameters in WQI calculations that significantly contributed to increasing the WQI. The elevated values may be attributed to the influence of carbonate stone dissolution and mechanical erosion under weathering conditions that are prevalent during winter season in the catchment area. As a consequence of lithostratigraphic unites product and GIS technique integration and normalization processes, most of water quality ranks are good and only autumn season has poor water quality in the 2012 and 2013, while in 2014 it has good water quality in the same season. The WQI values increase in general trend from winter to autumn seasons during the study period that may be referred to outflow by daily consumption, evaporation rising, and seepage water. The analysis shows that the modified water quality values of the Wadi Al-Arab Dam Reservoir (WADR) vary after using Bicarbonate and Calcium parameters by constant value. Generally, the results signify that the WADR is not polluted based on the physical and chemical characteristics of water.
文摘To categorize the nations to reflect the development status, to date, there are many conceptual frameworks. The Human Development index (HDI) that is published by the United Nations Development Programme is widely accepted and practiced by many people such as academicians, politicians, and donor organizations. However, though the development of HDI has gone through many revisions since its formulation in 1990, even the current version of the index formulation published in 2016 needs research to better understand and to gap-fill the knowledge base that can enhance the index formulation to facilitate the direction of attention such as release of funds. Therefore, in this paper, based on principal component analysis and K-means clustering algorithm, the data that reflect the measures of life expectancy index (LEI), education index (EI), and income index (II) are analyzed to categorize and to rank the member states of the UN using R statistical software package, an open source extensible programming language for statistical computing and graphics. The outcome of the study shows that the proportion of total eigen value (i.e., proportion of total variance) explained by PCA-1 (i.e., first principal component) accounts for more than 85% of the total variation. Moreover, the proportion of total eigen value explained by PCA-1 increases with time (i.e., yearly) though the amount of increase with time is not significant. However, the proportions of total eigen value explained by PCA-2 and PCA-3 decrease with time. Therefore, the loss of information in choosing PCA-1 to represent the chosen explanatory variables (i.e., LEI, EI, and II) may diminish with time if the trend of increasing pattern of proportion of total eigen value explained by PCA-1 with time continues in the future as well. On the other hand, the correlation between EI and PCA-1 increases with time although the magnitude of increase is not that significant. This same trend is observed in II as well. However, in contrast to these observations, the correlation between PCA-1 and LEI decreases with time. These findings imply that the contributions of EI and II to PCA-1 increase with time, but the contribution of LEI to PCA-1 decreases with time. On top of these, as per Hopkins statistic, the clusterability of the information conveyed by PCA-1 alone is far better than the clusterability of the information conveyed by PCA scores (i.e., PCA-1, PCA-2, and PCA-3) and the explanatory variables. Therefore, choosing PCA-1 to represent the chosen explanatory variables is becoming more concrete.
文摘In this paper, three rock types including Sandstone, Mudstone, and Crystalline Gypsum were part of a laboratory study conducted to develop a dataset for predicting the unconfined compressive strength of UAE intact sedimentary rock specimens. Four hundred nineteen rock samples from various areas along the coastal region of the UAE were collected and tested for the development of this dataset and evaluation of models. From the statistical analysis of the data, regression equations were established among rock parameters and correlations were expressed and compared by the ones proposed in literature.
基金Supported by the National Natural Science Foundation of China(No.41772155)the National Science and Technology Major Project of China(No.2016ZX05044-002)the Fundamental Research Funds for the Central Universities of China(No.2015XKZD07)
文摘Based on the productivity equation of coalbed methane (CBM) well, considering the impact of coal reservoir reformability on gas well productivity, the main production layer optimization index in the “three-step method” of optimal combination of production layers is corrected, and then the CBM production layer potential index is introduced to evaluate favorable areas for commingled multi-coal seam production. Through analysis of the key parameters of coal reservoirs affecting the CBM productivity index, a development unit division method for areas with multi-coal seams is established, and a quantitative grading index system is proposed. On this basis, the evaluation process of CBM development favorable area is developed: the mature 3-D modeling technology is used to characterize the reservoir physical properties of multi-coal seams in full-scale;the production layer potential index of each grid is calculated, and the production layer potential index contour under single-layer or commingled multi-layer production are plotted;according to the distribution of the contour of production layer potential index, the quantitative index of CBM development unit is adopted to outline the grade I, II, III coal reservoir distribution areas, and thus to pick out the favorable development areas. The practical application in the Yuwang block of Laochang in Yunnan proved that the favorable area evaluation process proposed can effectively overcome the defects of selecting favorable development areas only relying on evaluation results of a major coal seam pay, and enhance the accuracy of the evaluation results, meeting the requirements of selecting favorable areas for multi-coal seam commingled CBM production.
文摘Data Envelopment Analysis (DEA) is becoming an increasingly popular tool for assessing the relative performance of industries and companies. By applying DEA theory to the non-financial sector, the relative efficiency of 27 listed corporations in the United Arab Emirates (UAE) has been analyzed in this paper. The focus of the study has been on the impact of the financial crisis and the recovery thereafter. Further, the productivity change was decomposed into technical efficiency change and technological change by using the non-parametric Malmquist Productivity Index (MPI) over the period from 2007 to 2014. Based on Malmquist analysis, we find that the most efficient industries during the post-crisis period were food and beverages, telecommunication and pharmaceuticals. In contrast, the sectors that were adversely affected by the crisis were services, real estate, construction and cements. The break-up of the TFP indicated that the efficiency indices in the top performing industries were driven by technological improvements or frontier effects. The top-performing companies in the UAE during the 2007-14 period demonstrated innovation-led growth, aided by the use of better technology, investments in capital equipment, and adoption of new production processes.
文摘In this paper, the following results are proved: (1) Using both deletion strategy and lock strategy, resolution is complete for a clause set where literals with the same predicate or proposition symbol have the same index. (2) Using deletion strategy, both positive unit lock resolution and input lock resolution are complete for a Horn set where the indexes of positive literals are greater than those of negative literals. (3) Using deletion strategy, input half-lock resolution is complete for a Horn set. Keywords Resolution - index strategy - deletion strategy - unit resolution - input resolution Xiaochun Cheng had his Ph.D in 1996. He has been working as a lecturer at The University of Reading since 2000. He is a vip professor at North East Normal University and at Beijing Normal University. His research interests include theoretical and applied aspects on decision support systems, knowledge-based systems, intelligent systems.
基金Supported by National Key Basic Research Program of China(973 Program,Grant No.2014CB046405)Hebei Provincial Applied Basic Research Program(Grant No.12962147D)National Natural Science Foundation of China(Grant No.51375423)
文摘The previous sensitivity analysis researches are not accurate enough and also have the limited reference value, because those mathematical models are relatively simple and the change of the load and the initial displacement changes of the piston are ignored, even experiment verification is not conducted. Therefore, in view of deficiencies above, a nonlinear mathematical model is established in this paper, including dynamic characteristics of servo valve, nonlinear characteristics of pressure-flow, initial displacement of servo cylinder piston and friction nonlinearity. The transfer function block diagram is built for the hydraulic drive unit closed loop position control, as well as the state equations. Through deriving the time-varying coefficient items matrix and time-varying free items matrix of sensitivity equations respectively, the expression of sensitivity equations based on the nonlinear mathematical model are obtained. According to structure parameters of hydraulic drive unit, working parameters, fluid transmission characteristics and measured friction-velocity curves, the simulation analysis of hydraulic drive unit is completed on the MATLAB/Simulink simulation platform with the displacement step 2 mm, 5 mm and 10 mm, respectively. The simulation results indicate that the developed nonlinear mathematical model is sufficient by comparing the characteristic curves of experimental step response and simulation step response under different constant load. Then, the sensitivity function time-history curves of seventeen parameters are obtained, basing on each state vector time-history curve of step response characteristic. The maximum value of displacement variation percentage and the sum of displacement variation absolute values in the sampling time are both taken as sensitivity indexes. The sensitivity indexes values above are calculated and shown visually in histograms under different working conditions, and change rules are analyzed. Then the sensitivity indexes values of four measurable parameters, such as supply pressure, proportional gain, initial position of servo cylinder piston and load force, are verified experimentally on test platform of hydraulic drive unit, and the experimental research shows that the sensitivity analysis results obtained through simulation are approximate to the test results. This research indicates each parameter sensitivity characteristics of hydraulic drive unit, the performance-affected main parameters and secondary parameters are got under different working conditions, which will provide the theoretical foundation for the control compensation and structure optimization of hydraulic drive unit.
