This paper mainly studies the well-posedness of steady incompressible impinging jet flow problem through a 3D axisymmetric finitely long nozzle.This problem originates from the physical phenomena encountered in practi...This paper mainly studies the well-posedness of steady incompressible impinging jet flow problem through a 3D axisymmetric finitely long nozzle.This problem originates from the physical phenomena encountered in practical engineering fields,such as in short take-off and vertical landing(STOVL)aircraft.Nowadays many intricate phenomena associated with impinging jet flows remain inadequately elucidated,which limits the ability to optimize aircraft design.Given a boundary condition in the inlet,the impinging jet problem is transformed into a Bernoulli-type free boundary problem according to the stream function.Then the variational method is used to study the corresponding variational problem with one parameter,thereby the wellposedness is established.The main conclusion is as follows.For a 3D axisymmetric finitely long nozzle and an infinitely long vertical wall,given an axial velocity in the inlet of nozzle,there exists a unique smooth incom‑pressible impinging jet flow such that the free boundary initiates smoothly at the endpoint of the nozzle and extends to infinity along the vertical wall at far fields.The key point is to investigate the regularity of the corner where the nozzle and the vertical axis intersect.展开更多
Jet agitation is known as a maintenance-free stirring technique for nuclear wastewater treatment and demonstrates great potential in transport of radioactive particles.Removal processes of horizontal sediment beds dri...Jet agitation is known as a maintenance-free stirring technique for nuclear wastewater treatment and demonstrates great potential in transport of radioactive particles.Removal processes of horizontal sediment beds driven by impinging jets were experimentally investigated using image capture and processing technique.The beds were composed of heavy fine particles with particle density ranging from 3700 to 12600 kg·m^(-3) and particle diameter from 5 to 100 μm.The jet Reynolds number varied between 4300 and 9600.The single-phase large eddy simulation method was used for calculating both jet flow characteristics and wall shear stresses.The effects of jet strength,particle density,particle diameter,and bed thickness on bed mobility in terms of the critical Shields numbers were considered.Specifically,the critical Shields number was found to be intricately related to properties of particles,and independent of jet intensity.A new Shields number curve for stainless-steel particles was found,and a model was proposed to predict the transport rate of thin beds,with R^(2)=0.96.展开更多
This paper is devoted to the study of the shape of the free boundary for a threedimensional axisymmetric incompressible impinging jet.To be more precise,we will show that the free boundary is convex to the fluid,provi...This paper is devoted to the study of the shape of the free boundary for a threedimensional axisymmetric incompressible impinging jet.To be more precise,we will show that the free boundary is convex to the fluid,provided that the uneven ground is concave to the fluid.展开更多
This research comprehensively investigates the flow and thermal characteristics of a pulsating impinging jet over a dimpled surface.It analyzes the impact of key parameters(e.g.,inlet velocity pulsation functions,puls...This research comprehensively investigates the flow and thermal characteristics of a pulsating impinging jet over a dimpled surface.It analyzes the impact of key parameters(e.g.,inlet velocity pulsation functions,pulsation frequency,amplitude,dimple pitch,dimple depth,Reynolds number)on flow patterns and heat transfer.Validated computational fluid dynamics and the Re-normalization group turbulence model are employed to accurately simulate complex turbulent flow behavior.Local and average heat transfer coefficients are calculated and compared to steady impingement cases,revealing the potential benefits of pulsation for heat transfer enhancement.The study also examines how pulsation-induced flow modulation and thermal mixing affect heat transfer mechanisms.Results indicate that combining fluctuating flow with a dimpled surface can improve heat transfer rates.In summary,increasing pulsation amplitude consistently enhances heat transfer,while the effect of frequency varies between impinging and wall jet zones.展开更多
A low Reynolds number k-ε model is used in the numeri cal study on a circular semi-confined turbulent impinging jet . The result is c ompared with that of the standard k-ε model and a refined k-ε mode l, which re-c...A low Reynolds number k-ε model is used in the numeri cal study on a circular semi-confined turbulent impinging jet . The result is c ompared with that of the standard k-ε model and a refined k-ε mode l, which re-consi-dered the fluctuating pressure diffusion term in the dissipa tion rate equation (ε-equation) through modeling. It shows that the low Re ynolds number k-ε model and the standard k-ε model yield very poor performance, while the predicting ability of the refined k-ε model is mu ch improved , especially for the turbulent kinetic energy k. So it can be co ncluded that the poor performance of the standard k-ε model is owing to t he incorrect considering the effect of the fluctuating pressure diffusion term r ather than the use of the wall function near the wall just as presumed in the re ference.展开更多
A computational model combining large .eddy simulation with quadrature moment method was em-ployed to study nanoparticle evolution in a confined impinging jet. The investigated particle size is limited in the transien...A computational model combining large .eddy simulation with quadrature moment method was em-ployed to study nanoparticle evolution in a confined impinging jet. The investigated particle size is limited in the transient regime, and the particle collision kernel was obtained by using the theory of flux matching. The simulation was validated by comparing it with the experimental results. The numerical results show coherent structure acts to dominate particle number intensity, size and polydispersity distributions, and it also induce particle-laden iet to be diluted by .the ambient.The evolution of particle dynarnics in.the impinging jet flow are strongly related to the Rey-nolds number and nozzle-to-plate distance, and their relationships were analyzed.展开更多
An experimental study on the Klystron effect of periodic injection modulated by pressure drop fluctuations on subsequent atomization is conducted. Time-resolved atomization backlit images and atomization Mie scatter i...An experimental study on the Klystron effect of periodic injection modulated by pressure drop fluctuations on subsequent atomization is conducted. Time-resolved atomization backlit images and atomization Mie scatter images are captured by using the high speed camera. It is found that periodicity of forced atomization relies on pressure drop fluctuation amplitude and phase differences between atomization and pressure drop fluctuations relate to fluctuation frequencies. This feature of periodic atomization induced by Klystron effect corresponds to periodicities and high amplitudes of pressure fluctuations in unstable combustion chambers and chaos and low amplitudes of pressure fluctuations in stable combustions chambers. Drastically periodic varying of gross surface area of droplets with time was shown in Mie scatter images. The importance of periodic impinging jet atomization modulated by pressure drop fluctuations for acoustic liquid propellant combustion instabilities is illustrated.展开更多
Confined impinging jet reactor(CIJR)offers advantages for chemical rapid processes and has become an important new reactor used in the chemical industry.The micromixing efficiency in a T-shaped CIJR for two tubes of i...Confined impinging jet reactor(CIJR)offers advantages for chemical rapid processes and has become an important new reactor used in the chemical industry.The micromixing efficiency in a T-shaped CIJR for two tubes of inner diameter of 3 mm was studied by using a parallel competing iodide–iodate reaction as the working system.In this work,the effects of different operating conditions,such as impinging velocity and acid concentration,on segregation index were investigated.In addition,the effects of the inner nozzles diameter and the distance L between the jet axis and the top wall of the mixing chamber on the micromixing efficiency were also considered.It is concluded that the best range of L in this CIJR is 6.5–12.5 mm.Based on the incorporation model,the estimated minimum micromixing time tmof CIJR approximately equals to 2×10-4s.These experimental results indicate clearly that CIJR possesses a much better micromixing performance compared with the conventional stirred tank(micromixing time of 2×10-3to 2×10-2s).Hence,it can be envisioned that CIJR has more promising applications in various industrial processes.展开更多
Experiments were carried out to study the heat transfer performance of an impinging jet in a cross flow.Several parameters including the jet-to-cross-flow mass ratio(X=2%-8%), the Reynolds number(Red=1434-5735)and the...Experiments were carried out to study the heat transfer performance of an impinging jet in a cross flow.Several parameters including the jet-to-cross-flow mass ratio(X=2%-8%), the Reynolds number(Red=1434-5735)and the jet diameter(d=2-4 mm) were explored. The heat transfer enhancement factor was found to increase with the jet-to-cross-flow mass ratio and the Reynolds number, but decrease with the jet diameter when other parameters maintain fixed. The presence of a cross flow was observed to degrade the heat transfer performance in respect to the effect of impinging jet to the target surface only. In addition, an impinging jet was confirmed to be capable of enhancing the heat transfer process in considerable amplitude even though the jet was not designed to impinge on the target surface.展开更多
The extraction fraction E and overall volumetric mass transfer coefficient kka of TBP extracting butyric acid pro- cess in confined impinging jet reactors （CIJR） with two jets were investigated. The main variables t...The extraction fraction E and overall volumetric mass transfer coefficient kka of TBP extracting butyric acid pro- cess in confined impinging jet reactors （CIJR） with two jets were investigated. The main variables tested were the concentration of tri-butyl-phosphate （TBP） and butyric acid, the impinging velocity V, the impinging velocityratio of two phases Vorg/Vaq, the nozzle inner diameter di and the distance L between the jet axes and the top wall of the impinging chamber. The results showed that E and kLa increase with an increase of the impinging velocity V, the concentration ofTBP Corg, and the impinging velocity ratio Vor/Vaq. However, E and kta decrease with an increase of the inner diameter d1 from 1 to 2 mm, the concentration of butyric acid Caq from 0.5% （v/v） to 2% （v/v）. The factor L ranging from 3 to 11 mm has a negligible effect on E and kLa. A correlation on these variables and kLa was proposed based on the experimental data. These results indicated good mass transfer oerformance of CIJR in the extraction operation.展开更多
The objective of this dissertation is to investigate the impinging jet under the influence of crossflow. It has been known that there exist jet shear layer, impingement on the bottom wall, interactions between the ind...The objective of this dissertation is to investigate the impinging jet under the influence of crossflow. It has been known that there exist jet shear layer, impingement on the bottom wall, interactions between the induced wall jet and the ambient crossflow in near field. There are few intensive studies of the impinging jet in crossflow at home and abroad due to the complexities of flow, such as the formation and evolution of the vortical structures, interactions among vortices, while researches on the temporal and spatial evolution of these vortical structures can promote the practical applications in environment engineering, hydroelectricity engineering, etc., and provide the basis for flow control and improvement through revealing the inherent mechanism and development of the vortical structures.展开更多
An electrochemical cell consisting of a double horizontal Impinging Jet Cell (IJC) has been conceived and characterized. The purpose of this system is the simultaneous electrodeposition of a composite metal/particle c...An electrochemical cell consisting of a double horizontal Impinging Jet Cell (IJC) has been conceived and characterized. The purpose of this system is the simultaneous electrodeposition of a composite metal/particle coating on both surfaces of a metal sheet. The silica particles imprint in the nickel matrix has allowed to distinguish four different flow areas onto the electrode namely the stagnation area, the radial flow area characterized by a higher flow speed, the return flow area that involves gravity effect, and the drainage area with a constant draining speed. Based on the limiting current evolution as a function of the Reynolds number, three flow modes were extracted: the Laminar Low Flow (LLF), the Laminar High Flow (LHF) and the Disturbance. The IJC investigated ensures a laminar flow for a large range of flow rate from a nozzle-to-sample distance of 19 mm and creates an laminar flow ovoid plan merged with the sample for the high flows.展开更多
The method of numerical simulation was applied to investigate the effects of jet impinging plate thickness and its thermal conductivity on the local heat flux distribution along the impinging plate. The results show t...The method of numerical simulation was applied to investigate the effects of jet impinging plate thickness and its thermal conductivity on the local heat flux distribution along the impinging plate. The results show that the two factors have great effects on the heat flux distribution. The non-uniformity of the local heat-flux on the impinging plate surface gets more profound as the plate becomes thicker and thermal conductivity gets larger. When Reynolds number is 5000, the ratio of nozzle-to-plate spacing to nozzle diameter is 5 and thermal conductivity is 16W/(m·K), and even for the plate with only 25μm in thickness, the non-uniformity of the heat flux cannot be neglected. When the plate thickness is 50 μm, only when thermal conductivity is as small as 1W/(m·K), the heat flux curve can be approximately treated as an iso-heat-flux boundary. In the experimental research, a real non-iso-heat-flux boundary is treated as an iso-heat-flux boundary, which would result in under-estimated Nusselt number value in the stagnation zone and an over-estimated value outside. Such an experimental Nusselt number distribution is taken to evaluate turbulent model, and the conclusion would be drawn that the turbulent model over-predicts the stagnation heat transfer. This is one of the important reasons why many literatures reported that k-ε turbulent model dramatically over-predicts the impinging jet heat transfer in the stagnation region.展开更多
Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Theref...Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Therefore, the jet breakup should be avoided as possible in industrial production. The objective of this study is to find the relation of the processing parameters of the ACC equipment versus the breakup length of jet with weaker turbulence. To obtain quantitative findings, not only relative experimental study but also numerical simulation was carded out. For a weaker turbulent water jet, the breakup length increases with the increase of jet diameter, as well as with the jet velocity; jet diameter has a significant effect on the breakup length for a certain flow rate when compared with jet velocity; finally a suggested correlation of the jet breakup length versus jet Weber number is presented in this study.展开更多
To overcome the disadvantages of displacement ventilation( DV) and traditional mixing ventilation( MV) system,a new ventilation system known as impinging jet ventilation system( IJVS)has been developing. The warm air ...To overcome the disadvantages of displacement ventilation( DV) and traditional mixing ventilation( MV) system,a new ventilation system known as impinging jet ventilation system( IJVS)has been developing. The warm air can be supplied with impinging jet ventilation( IJV), while the DV is only used for cooling.However,the flow and temperature field of IJV under heating scenario has had few references. The paper is mainly focused on computational fluid dynamics( CFD) and developing an adequate correlation between the distance L that warm air can reach and different parameters in the warm IJVS by using response surface methodology( RSM). The results indicate that L decreases as the supply velocity υ decreases but increases as the supply temperature difference ΔT or the discharge height h decreases. In the variable air volume( VAV) system, it is necessary to determine supply parameters both under the maximum-heat-load condition and the small-heat-load condition. Unlike the VAV system,the constant air volume( CAV) system has no need to study the small-heat-load condition. Draught discomfort near the nozzle becomes the issue of concern in IJVS, thus the suitable discharge height is of great importance in design and can be calculated based on the predictive model.展开更多
In this study, we apply the optical flow method to the time-series shadowgraph images of impinging jets using a high-speed video camera with high spatial and temporal resolution. This image analysis provides quantitat...In this study, we apply the optical flow method to the time-series shadowgraph images of impinging jets using a high-speed video camera with high spatial and temporal resolution. This image analysis provides quantitative velocity vector fields in the object space without tracer particles. The analysis results clearly capture the details of the coherent vortex structure and its advection from the shear layer of the free jet. Although the results still leave challenges for the quantitative validation, the results show that this analysis method is effective for understanding the details of the physical phenomenon based on the quantitative values extracted from the shadowgraph images.展开更多
Mist jet impingement cooling is an enhanced heat transfer method widely used after the continuous galvanizing process. The key of a successful design and operation of the mist jet impingement cooling system lies in ma...Mist jet impingement cooling is an enhanced heat transfer method widely used after the continuous galvanizing process. The key of a successful design and operation of the mist jet impingement cooling system lies in mastering heat transfer coefficients. The heat transfer coefficients of high temperature steel plates cooled with multiple mist impinging jets were experimentally investigated, and the effects of gas and water flow rates on heat transfer coefficients were studied. The test results illustrate that the gas flow rate has little effect on the mist heat transfer rate. It is also found that the water flow rate has a great impact on the heat transfer coefficient. When the water flow rate ranges from 0.96m3/h to 1.59 m3/h, an increase in the rate will produce a higher heat transfer coefficient with a maximum of 5650 W/（m2 · K）. Compared with the conventional gas jet cooling, the heat transfer coefficient of the mist jet cooling will be much higher, which can effectively strengthen the after-pot cooling.展开更多
This review summarizes recent progress in the study of impinging-jet dynamics and atomization,with a focus on liquid sheet formation,instability mechanisms,and the influence of key parameters such as fluid properties,...This review summarizes recent progress in the study of impinging-jet dynamics and atomization,with a focus on liquid sheet formation,instability mechanisms,and the influence of key parameters such as fluid properties,Weber number,and Reynolds number.Special attention is given to atomization behaviors under high pressure and external perturbations.Representative experimental and numerical approaches are introduced,and critical findings under complex conditions are highlighted.In addition,practical applications of impinging-jet technology in aerospace propulsion,biomedical devices,and energy science are discussed.This review aims to serve as a concise reference for researchers interested in multiphase flow dynamics and engineering applications of impinging jets.展开更多
Impinging jet arrays are extensively used in numerous industrial operations,including the cooling of electronics,turbine blades,and other high-heat flux systems because of their superior heat transfer capabilities.Opt...Impinging jet arrays are extensively used in numerous industrial operations,including the cooling of electronics,turbine blades,and other high-heat flux systems because of their superior heat transfer capabilities.Optimizing the design and operating parameters of such systems is essential to enhance cooling efficiency and achieve uniform pressure distribution,which can lead to improved system performance and energy savings.This paper presents two multi-objective optimization methodologies for a turbulent air jet impingement cooling system.The governing equations are resolved employing the commercial computational fluid dynamics(CFD)software ANSYS Fluent v17.The study focuses on four controlling parameters:Reynolds number(Re),swirl number(S),jet-to-jet separation distance(Z/D),and impingement height(H/D).The effects of these parameters on heat transfer and impingement pressure distribution are investigated.Non-dominated Sorting Genetic Algorithm(NSGA-II)and Weighted Sum Method(WSM)are employed to optimize the controlling parameters for maximum cooling performance.The aim is to identify optimal design parameters and system configurations that enhance heat transfer efficiency while achieving a uniform impingement pressure distribution.These findings have practical implications for applications requiring efficient cooling.The optimized design achieved a 12.28%increase in convective heat transfer efficiency with a local Nusselt number of 113.05 compared to 100.69 in the reference design.Enhanced convective cooling and heat flux were observed in the optimized configuration,particularly in areas of direct jet impingement.Additionally,the optimized design maintained lower wall temperatures,demonstrating more effective thermal dissipation.展开更多
Parabolic trough collectors are essential components of solar thermal power plants,and the non-uniform heat flux on the walls may lead to low heat transfer coefficients and large wall temperature differences.A novel j...Parabolic trough collectors are essential components of solar thermal power plants,and the non-uniform heat flux on the walls may lead to low heat transfer coefficients and large wall temperature differences.A novel jet structure is proposed in this paper to explore the feasibility of adopting impinging jets to improve the heat transfer performance of the collector tube with supercritical carbon dioxide(S-CO_(2))as the working fluid.The physical model is built based on several assumptions,and numerical simulations are performed under the mass flow rate of 0.25-0.75 kg/s and the average surface heat flux of 14.7-33 kW/m^(2).Firstly,performance comparisons are made between the jet and tube-in-tube structures.The results show that the average heat transfer coefficient h of the jet structure is 46.5%higher than that of the tube-in-tube structure and the corresponding average temperature differenceΔT between the wall and S-CO_(2)is 31.7%lower.Secondly,the effects of the jet hole circumferential position and diameter on heat transfer are investigated.It's found that by adjusting the circumferential position of the jet hole from 60°to 120°and matching the impingement area of the jets and the high heat flux region,h can be increased by 14.2%andΔT can be reduced by 12.4%.h is also found to be increased by 77.4%when the jet hole diameter is reduced from D=9.7 mm to D=5 mm.Furthermore,the jet structure is further modified by incorporating it with the eccentric configuration.The effect of eccentricity e is studied in detail,and results show that appropriate eccentricity results in higher h and smallerΔT due to the decreased impingement distance and the increased heat transfer.This study can guide the design and optimization of parabolic trough collectors.展开更多
文摘This paper mainly studies the well-posedness of steady incompressible impinging jet flow problem through a 3D axisymmetric finitely long nozzle.This problem originates from the physical phenomena encountered in practical engineering fields,such as in short take-off and vertical landing(STOVL)aircraft.Nowadays many intricate phenomena associated with impinging jet flows remain inadequately elucidated,which limits the ability to optimize aircraft design.Given a boundary condition in the inlet,the impinging jet problem is transformed into a Bernoulli-type free boundary problem according to the stream function.Then the variational method is used to study the corresponding variational problem with one parameter,thereby the wellposedness is established.The main conclusion is as follows.For a 3D axisymmetric finitely long nozzle and an infinitely long vertical wall,given an axial velocity in the inlet of nozzle,there exists a unique smooth incom‑pressible impinging jet flow such that the free boundary initiates smoothly at the endpoint of the nozzle and extends to infinity along the vertical wall at far fields.The key point is to investigate the regularity of the corner where the nozzle and the vertical axis intersect.
文摘Jet agitation is known as a maintenance-free stirring technique for nuclear wastewater treatment and demonstrates great potential in transport of radioactive particles.Removal processes of horizontal sediment beds driven by impinging jets were experimentally investigated using image capture and processing technique.The beds were composed of heavy fine particles with particle density ranging from 3700 to 12600 kg·m^(-3) and particle diameter from 5 to 100 μm.The jet Reynolds number varied between 4300 and 9600.The single-phase large eddy simulation method was used for calculating both jet flow characteristics and wall shear stresses.The effects of jet strength,particle density,particle diameter,and bed thickness on bed mobility in terms of the critical Shields numbers were considered.Specifically,the critical Shields number was found to be intricately related to properties of particles,and independent of jet intensity.A new Shields number curve for stainless-steel particles was found,and a model was proposed to predict the transport rate of thin beds,with R^(2)=0.96.
基金supported in part by the National Natural Science Foundation of China(12101088)the Natural Science Foundation of Sichuan Province(2022NSFSC1858)。
文摘This paper is devoted to the study of the shape of the free boundary for a threedimensional axisymmetric incompressible impinging jet.To be more precise,we will show that the free boundary is convex to the fluid,provided that the uneven ground is concave to the fluid.
文摘This research comprehensively investigates the flow and thermal characteristics of a pulsating impinging jet over a dimpled surface.It analyzes the impact of key parameters(e.g.,inlet velocity pulsation functions,pulsation frequency,amplitude,dimple pitch,dimple depth,Reynolds number)on flow patterns and heat transfer.Validated computational fluid dynamics and the Re-normalization group turbulence model are employed to accurately simulate complex turbulent flow behavior.Local and average heat transfer coefficients are calculated and compared to steady impingement cases,revealing the potential benefits of pulsation for heat transfer enhancement.The study also examines how pulsation-induced flow modulation and thermal mixing affect heat transfer mechanisms.Results indicate that combining fluctuating flow with a dimpled surface can improve heat transfer rates.In summary,increasing pulsation amplitude consistently enhances heat transfer,while the effect of frequency varies between impinging and wall jet zones.
文摘A low Reynolds number k-ε model is used in the numeri cal study on a circular semi-confined turbulent impinging jet . The result is c ompared with that of the standard k-ε model and a refined k-ε mode l, which re-consi-dered the fluctuating pressure diffusion term in the dissipa tion rate equation (ε-equation) through modeling. It shows that the low Re ynolds number k-ε model and the standard k-ε model yield very poor performance, while the predicting ability of the refined k-ε model is mu ch improved , especially for the turbulent kinetic energy k. So it can be co ncluded that the poor performance of the standard k-ε model is owing to t he incorrect considering the effect of the fluctuating pressure diffusion term r ather than the use of the wall function near the wall just as presumed in the re ference.
基金Supported by the Ministry of Science and Technology of China (No.2005CCA06900).
文摘A computational model combining large .eddy simulation with quadrature moment method was em-ployed to study nanoparticle evolution in a confined impinging jet. The investigated particle size is limited in the transient regime, and the particle collision kernel was obtained by using the theory of flux matching. The simulation was validated by comparing it with the experimental results. The numerical results show coherent structure acts to dominate particle number intensity, size and polydispersity distributions, and it also induce particle-laden iet to be diluted by .the ambient.The evolution of particle dynarnics in.the impinging jet flow are strongly related to the Rey-nolds number and nozzle-to-plate distance, and their relationships were analyzed.
基金supported by the National Natural Science Foundation of China (Nos. 11502186 and 51606138)the National Key Basic Research Program of ChinaNational Key Scientific Instrument and the Equipment Development Projects of China (No. 2012YQ04016408)
文摘An experimental study on the Klystron effect of periodic injection modulated by pressure drop fluctuations on subsequent atomization is conducted. Time-resolved atomization backlit images and atomization Mie scatter images are captured by using the high speed camera. It is found that periodicity of forced atomization relies on pressure drop fluctuation amplitude and phase differences between atomization and pressure drop fluctuations relate to fluctuation frequencies. This feature of periodic atomization induced by Klystron effect corresponds to periodicities and high amplitudes of pressure fluctuations in unstable combustion chambers and chaos and low amplitudes of pressure fluctuations in stable combustions chambers. Drastically periodic varying of gross surface area of droplets with time was shown in Mie scatter images. The importance of periodic impinging jet atomization modulated by pressure drop fluctuations for acoustic liquid propellant combustion instabilities is illustrated.
基金Supported by the National Natural Science Foundation of China(21206002,21121064,20990224)the State Key Laboratory of Chemical Engineering(SKL-Ch E-13A03)
文摘Confined impinging jet reactor(CIJR)offers advantages for chemical rapid processes and has become an important new reactor used in the chemical industry.The micromixing efficiency in a T-shaped CIJR for two tubes of inner diameter of 3 mm was studied by using a parallel competing iodide–iodate reaction as the working system.In this work,the effects of different operating conditions,such as impinging velocity and acid concentration,on segregation index were investigated.In addition,the effects of the inner nozzles diameter and the distance L between the jet axis and the top wall of the mixing chamber on the micromixing efficiency were also considered.It is concluded that the best range of L in this CIJR is 6.5–12.5 mm.Based on the incorporation model,the estimated minimum micromixing time tmof CIJR approximately equals to 2×10-4s.These experimental results indicate clearly that CIJR possesses a much better micromixing performance compared with the conventional stirred tank(micromixing time of 2×10-3to 2×10-2s).Hence,it can be envisioned that CIJR has more promising applications in various industrial processes.
基金Supported by the National Natural Science Foundation of China(51106140)the Natural Science Foundation of Zhejiang Province(Z1110695)
文摘Experiments were carried out to study the heat transfer performance of an impinging jet in a cross flow.Several parameters including the jet-to-cross-flow mass ratio(X=2%-8%), the Reynolds number(Red=1434-5735)and the jet diameter(d=2-4 mm) were explored. The heat transfer enhancement factor was found to increase with the jet-to-cross-flow mass ratio and the Reynolds number, but decrease with the jet diameter when other parameters maintain fixed. The presence of a cross flow was observed to degrade the heat transfer performance in respect to the effect of impinging jet to the target surface only. In addition, an impinging jet was confirmed to be capable of enhancing the heat transfer process in considerable amplitude even though the jet was not designed to impinge on the target surface.
基金Supported by the National Natural Science Foundation of China(21206002,21376016)the State Key Laboratory of Chemical Engineering(SKL-Ch E-13A03)
文摘The extraction fraction E and overall volumetric mass transfer coefficient kka of TBP extracting butyric acid pro- cess in confined impinging jet reactors （CIJR） with two jets were investigated. The main variables tested were the concentration of tri-butyl-phosphate （TBP） and butyric acid, the impinging velocity V, the impinging velocityratio of two phases Vorg/Vaq, the nozzle inner diameter di and the distance L between the jet axes and the top wall of the impinging chamber. The results showed that E and kLa increase with an increase of the impinging velocity V, the concentration ofTBP Corg, and the impinging velocity ratio Vor/Vaq. However, E and kta decrease with an increase of the inner diameter d1 from 1 to 2 mm, the concentration of butyric acid Caq from 0.5% （v/v） to 2% （v/v）. The factor L ranging from 3 to 11 mm has a negligible effect on E and kLa. A correlation on these variables and kLa was proposed based on the experimental data. These results indicated good mass transfer oerformance of CIJR in the extraction operation.
文摘The objective of this dissertation is to investigate the impinging jet under the influence of crossflow. It has been known that there exist jet shear layer, impingement on the bottom wall, interactions between the induced wall jet and the ambient crossflow in near field. There are few intensive studies of the impinging jet in crossflow at home and abroad due to the complexities of flow, such as the formation and evolution of the vortical structures, interactions among vortices, while researches on the temporal and spatial evolution of these vortical structures can promote the practical applications in environment engineering, hydroelectricity engineering, etc., and provide the basis for flow control and improvement through revealing the inherent mechanism and development of the vortical structures.
文摘An electrochemical cell consisting of a double horizontal Impinging Jet Cell (IJC) has been conceived and characterized. The purpose of this system is the simultaneous electrodeposition of a composite metal/particle coating on both surfaces of a metal sheet. The silica particles imprint in the nickel matrix has allowed to distinguish four different flow areas onto the electrode namely the stagnation area, the radial flow area characterized by a higher flow speed, the return flow area that involves gravity effect, and the drainage area with a constant draining speed. Based on the limiting current evolution as a function of the Reynolds number, three flow modes were extracted: the Laminar Low Flow (LLF), the Laminar High Flow (LHF) and the Disturbance. The IJC investigated ensures a laminar flow for a large range of flow rate from a nozzle-to-sample distance of 19 mm and creates an laminar flow ovoid plan merged with the sample for the high flows.
基金Project(50376076) supported by the National Natural Science Foundation of China
文摘The method of numerical simulation was applied to investigate the effects of jet impinging plate thickness and its thermal conductivity on the local heat flux distribution along the impinging plate. The results show that the two factors have great effects on the heat flux distribution. The non-uniformity of the local heat-flux on the impinging plate surface gets more profound as the plate becomes thicker and thermal conductivity gets larger. When Reynolds number is 5000, the ratio of nozzle-to-plate spacing to nozzle diameter is 5 and thermal conductivity is 16W/(m·K), and even for the plate with only 25μm in thickness, the non-uniformity of the heat flux cannot be neglected. When the plate thickness is 50 μm, only when thermal conductivity is as small as 1W/(m·K), the heat flux curve can be approximately treated as an iso-heat-flux boundary. In the experimental research, a real non-iso-heat-flux boundary is treated as an iso-heat-flux boundary, which would result in under-estimated Nusselt number value in the stagnation zone and an over-estimated value outside. Such an experimental Nusselt number distribution is taken to evaluate turbulent model, and the conclusion would be drawn that the turbulent model over-predicts the stagnation heat transfer. This is one of the important reasons why many literatures reported that k-ε turbulent model dramatically over-predicts the impinging jet heat transfer in the stagnation region.
文摘Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Therefore, the jet breakup should be avoided as possible in industrial production. The objective of this study is to find the relation of the processing parameters of the ACC equipment versus the breakup length of jet with weaker turbulence. To obtain quantitative findings, not only relative experimental study but also numerical simulation was carded out. For a weaker turbulent water jet, the breakup length increases with the increase of jet diameter, as well as with the jet velocity; jet diameter has a significant effect on the breakup length for a certain flow rate when compared with jet velocity; finally a suggested correlation of the jet breakup length versus jet Weber number is presented in this study.
基金National Natural Science Foundation of China(No.51278094)the Innovation Foundation of Shanghai Education Commission,China(No.13ZZ054)
文摘To overcome the disadvantages of displacement ventilation( DV) and traditional mixing ventilation( MV) system,a new ventilation system known as impinging jet ventilation system( IJVS)has been developing. The warm air can be supplied with impinging jet ventilation( IJV), while the DV is only used for cooling.However,the flow and temperature field of IJV under heating scenario has had few references. The paper is mainly focused on computational fluid dynamics( CFD) and developing an adequate correlation between the distance L that warm air can reach and different parameters in the warm IJVS by using response surface methodology( RSM). The results indicate that L decreases as the supply velocity υ decreases but increases as the supply temperature difference ΔT or the discharge height h decreases. In the variable air volume( VAV) system, it is necessary to determine supply parameters both under the maximum-heat-load condition and the small-heat-load condition. Unlike the VAV system,the constant air volume( CAV) system has no need to study the small-heat-load condition. Draught discomfort near the nozzle becomes the issue of concern in IJVS, thus the suitable discharge height is of great importance in design and can be calculated based on the predictive model.
文摘In this study, we apply the optical flow method to the time-series shadowgraph images of impinging jets using a high-speed video camera with high spatial and temporal resolution. This image analysis provides quantitative velocity vector fields in the object space without tracer particles. The analysis results clearly capture the details of the coherent vortex structure and its advection from the shear layer of the free jet. Although the results still leave challenges for the quantitative validation, the results show that this analysis method is effective for understanding the details of the physical phenomenon based on the quantitative values extracted from the shadowgraph images.
文摘Mist jet impingement cooling is an enhanced heat transfer method widely used after the continuous galvanizing process. The key of a successful design and operation of the mist jet impingement cooling system lies in mastering heat transfer coefficients. The heat transfer coefficients of high temperature steel plates cooled with multiple mist impinging jets were experimentally investigated, and the effects of gas and water flow rates on heat transfer coefficients were studied. The test results illustrate that the gas flow rate has little effect on the mist heat transfer rate. It is also found that the water flow rate has a great impact on the heat transfer coefficient. When the water flow rate ranges from 0.96m3/h to 1.59 m3/h, an increase in the rate will produce a higher heat transfer coefficient with a maximum of 5650 W/（m2 · K）. Compared with the conventional gas jet cooling, the heat transfer coefficient of the mist jet cooling will be much higher, which can effectively strengthen the after-pot cooling.
基金supported by the National Natural Science Foundation of China(Grant Nos.U23B6009 and 12272050).
文摘This review summarizes recent progress in the study of impinging-jet dynamics and atomization,with a focus on liquid sheet formation,instability mechanisms,and the influence of key parameters such as fluid properties,Weber number,and Reynolds number.Special attention is given to atomization behaviors under high pressure and external perturbations.Representative experimental and numerical approaches are introduced,and critical findings under complex conditions are highlighted.In addition,practical applications of impinging-jet technology in aerospace propulsion,biomedical devices,and energy science are discussed.This review aims to serve as a concise reference for researchers interested in multiphase flow dynamics and engineering applications of impinging jets.
文摘Impinging jet arrays are extensively used in numerous industrial operations,including the cooling of electronics,turbine blades,and other high-heat flux systems because of their superior heat transfer capabilities.Optimizing the design and operating parameters of such systems is essential to enhance cooling efficiency and achieve uniform pressure distribution,which can lead to improved system performance and energy savings.This paper presents two multi-objective optimization methodologies for a turbulent air jet impingement cooling system.The governing equations are resolved employing the commercial computational fluid dynamics(CFD)software ANSYS Fluent v17.The study focuses on four controlling parameters:Reynolds number(Re),swirl number(S),jet-to-jet separation distance(Z/D),and impingement height(H/D).The effects of these parameters on heat transfer and impingement pressure distribution are investigated.Non-dominated Sorting Genetic Algorithm(NSGA-II)and Weighted Sum Method(WSM)are employed to optimize the controlling parameters for maximum cooling performance.The aim is to identify optimal design parameters and system configurations that enhance heat transfer efficiency while achieving a uniform impingement pressure distribution.These findings have practical implications for applications requiring efficient cooling.The optimized design achieved a 12.28%increase in convective heat transfer efficiency with a local Nusselt number of 113.05 compared to 100.69 in the reference design.Enhanced convective cooling and heat flux were observed in the optimized configuration,particularly in areas of direct jet impingement.Additionally,the optimized design maintained lower wall temperatures,demonstrating more effective thermal dissipation.
基金supported by the National Natural Science Foundation of China(Grant No.52376087)Hunan Provincial Natural Science Foundation of China(Grant No.2023JJ30688)。
文摘Parabolic trough collectors are essential components of solar thermal power plants,and the non-uniform heat flux on the walls may lead to low heat transfer coefficients and large wall temperature differences.A novel jet structure is proposed in this paper to explore the feasibility of adopting impinging jets to improve the heat transfer performance of the collector tube with supercritical carbon dioxide(S-CO_(2))as the working fluid.The physical model is built based on several assumptions,and numerical simulations are performed under the mass flow rate of 0.25-0.75 kg/s and the average surface heat flux of 14.7-33 kW/m^(2).Firstly,performance comparisons are made between the jet and tube-in-tube structures.The results show that the average heat transfer coefficient h of the jet structure is 46.5%higher than that of the tube-in-tube structure and the corresponding average temperature differenceΔT between the wall and S-CO_(2)is 31.7%lower.Secondly,the effects of the jet hole circumferential position and diameter on heat transfer are investigated.It's found that by adjusting the circumferential position of the jet hole from 60°to 120°and matching the impingement area of the jets and the high heat flux region,h can be increased by 14.2%andΔT can be reduced by 12.4%.h is also found to be increased by 77.4%when the jet hole diameter is reduced from D=9.7 mm to D=5 mm.Furthermore,the jet structure is further modified by incorporating it with the eccentric configuration.The effect of eccentricity e is studied in detail,and results show that appropriate eccentricity results in higher h and smallerΔT due to the decreased impingement distance and the increased heat transfer.This study can guide the design and optimization of parabolic trough collectors.
