To investigate the influence of non-uniform water distribution on the mechanical properties and failure behavior of red sandstone,we designed five immersion heights and durations to achieve varying non-uniform water d...To investigate the influence of non-uniform water distribution on the mechanical properties and failure behavior of red sandstone,we designed five immersion heights and durations to achieve varying non-uniform water distribution states.Uniaxial compression tests were conducted on red sandstone under these conditions.The effects of non-uniform water distribution on deformation,failure,strength,and energy characteristics of red sandstone were analyzed.The impact of non-uniform water distribution on the intensity of rock failure was discussed,and the failure mechanism under non-uniform water distribution was revealed.The hazards of low immersion heights on underground rock structures were analyzed.The results demonstrate that peak strength and elastic modulus of red sandstone exhibit high sensitivity to immersion height,with reductions of 38%and 23%respectively even at L=1/50H.Water immersion reduces both energy storage capacity and energy dissipation capability of red sandstone.The immersion height and duration influence the failure mode of red sandstone by controlling the migration and separation of dry-wet interfaces.Low immersion height poses significant risks to underground rock structures(e.g.,a 38%strength reduction when L=1/50H),and the concentration degree of water non-uniform distribution is the key factor in assessing the weakening effect of water on rocks.展开更多
In cold regions,rock structures will be weakened by freeze-thaw cycles under various water immersion conditions.Determining how water immersion conditions impact rock deterioration under freeze-thaw cycles is critical...In cold regions,rock structures will be weakened by freeze-thaw cycles under various water immersion conditions.Determining how water immersion conditions impact rock deterioration under freeze-thaw cycles is critical to assess accurately the frost resistance of engineered rock.In this paper,freeze-thaw cycles(temperature range of-20℃-20℃)were performed on the sandstones in different water immersion conditions(fully,partially and non-immersed in water).Then,computed tomography(CT)tests were conducted on the sandstones when the freeze-thaw number reached 0,5,10,15,20 and 30.Next,the effects of water immersion conditions on the microstructure deterioration of sandstone under freezethaw cycles were evaluated using CT spatial imaging,porosity and damage factor.Finally,focusing on the partially immersed condition,the immersion volume rate was defined to understand the effects of immersion degree on the freeze-thaw damage of sandstone and to propose a damage model considering the freeze-thaw number and immersion degree.The results show that with increasing freeze-thaw number,the porosities and damage factors under fully and partially immersed conditions increase continuously,while those under non-immersed condition first increase and then remain approximately constant.The most severe freeze-thaw damage occurs in fully immersed condition,followed by partially immersed condition and finally non-immersed condition.Interestingly,the freeze-thaw number and the immersion volume rate both impact the microstructure deterioration of the partially immersed sandstone.For the same freeze-thaw number,the damage factor increases approximately linearly with increasing immersion volume rate,and the increasing immersion degree exacerbates the microstructure deterioration of sandstone.Moreover,the proposed model can effectively estimate the freeze-thaw damage of partially immersed sandstone with different immersion volume rates.展开更多
This study focuses on the thermal management of 4680-type cylindrical lithium-ion battery packs utilizing NCM811 chemistry.It establishes coupled multi-physics models for both immersion and serpentine cold plate cooli...This study focuses on the thermal management of 4680-type cylindrical lithium-ion battery packs utilizing NCM811 chemistry.It establishes coupled multi-physics models for both immersion and serpentine cold plate cooling systems.Through a combination of numerical simulation and experimental validation,the technical advantages and mechanisms of immersion cooling are systematically explored.Simulation results indicate that under a 3C fast-charging condition(inlet temperature 20℃,flow rate 36 L/min),the immersion cooling structure 3demonstrates a triple enhancement in thermal performance compared to the cold plate structure 1:a 13.06%reduction in peak temperature,a 31.67%decrease in overall maximum temperature difference,and a 47.62%decrease in single-cell temperature deviation,while also reducing flow resistance by 33.61%.Furthermore,based on the immersion cooling model,a small battery module comprising seven cylindrical cells was designed for thermal runaway testing via nail penetration.The results show that the peak temperature of the triggered cell was limited to 437.6℃,with a controllable temperature rise gradient of only 3.35℃/s and a rapid cooling rate of 0.6℃/s.The maximum temperature rise of adjacent cells was just 64.8℃,effectively inhibiting thermal propagation.Post-test disassembly revealed that the non-triggered cells retained>99.2%of their original voltage and>99%structural integrity,confirming the module’s ability to achieve“localized failure with global stability.”展开更多
The self-healing properties of dual-component epoxy microcapsules are evaluated when incorporated into an epoxy coating.The performance of the coating was assessed under immersion in a saline solution,simulating seawa...The self-healing properties of dual-component epoxy microcapsules are evaluated when incorporated into an epoxy coating.The performance of the coating was assessed under immersion in a saline solution,simulating seawater conditions.Initially,synthesized microcapsules are incorporated into the epoxy coating.Then,the self-healing capabilities of the coating are studied under immersion using scanning vibrating electrode technique(SVET),open circuit potential(OCP),electrochemical impedance spectroscopy(EIS)and immersion corrosion test on coated samples with intentionally created artificial defects.The last three tests were conducted in a 3.5%NaCl solution.The adhesion of the coating is also studied by pull-off adhesion test.SVET analyses reveal lower ionic current densities in coated samples containing microcapsules during 24 h of immersion.EIS results demonstrate self-healing at the defect site for up to 12 h of immersion.After this time,the corrosion protection diminishes with prolonged immersion in the saline solution.Despite this,the coating with the microcapsules exhibits decrease in the corrosion process compared to the coating without the microcapsules.These results are consistent and complement the outcomes of the immersion tests conducted over 360 and 1056 h,which indicate that coated samples without microcapsules exhibit double the corroded areas around the scribes compared to coated samples containing the microcapsules.These findings offer a promising outlook for applying this coating on offshore carbon steel structures under immersion aiming for a longer lifetime with less maintenance intervention.展开更多
The challenge of effectively eliminating air during gastrointestinal endoscopy using ultrasound techniques is apparent.This difficulty arises from the intricacies of removing concealed air within the folds of the gast...The challenge of effectively eliminating air during gastrointestinal endoscopy using ultrasound techniques is apparent.This difficulty arises from the intricacies of removing concealed air within the folds of the gastrointestinal tract,resulting in artifacts and compromised visualization.In addition,the overlap of folds with lesions can obscure their depth and size,presenting challenges for an accurate assessment.Conversely,in intricately folded regions of the gastrointestinal tract,such as the stomach,intestine,and colon,insufficient delivery of air or CO_(2) into the cavity impedes luminal expansion,hindering the accurate visualization of lesions concealed within the folds.Although this underscores the requirement for substantial airflow,excessive airflow can hinder visualization of bleeding lesions and other abnormalities.Considering these challenges,an ideal endoscopic device would facilitate the observation of lesions without the requirement for air or CO_(2) delivery whereas,ensuring optimal expansion of the gastrointestinal tract.Recently,transparent gels with specific viscosities have been employed more frequently to address this issue.This review aims to elucidate how these gels address these challenges and provide a solution for enhanced endoscopic visualization.展开更多
Although room-temperature superconductivity is still difficult to achieve,researching materials with electrical conductivity significantly higher than that of copper will be of great importance in improving energy eff...Although room-temperature superconductivity is still difficult to achieve,researching materials with electrical conductivity significantly higher than that of copper will be of great importance in improving energy efficiency,reducing costs,lightening equipment weight,and enhancing overall performance.Herein,this study presents a novel copper-carbon nanofilm composite with enhanced conductivity which has great applications in the electronic devices and electrical equipment.Multilayer copper-carbon nanofilms and interfaces with superior electronic structures are formed based on copper materials using plasma immersion nanocarbon layer deposition technology,effectively enhancing conductivity.Experimental results show that for a five-layer copper-carbon nanofilm composite,the conductivity improves significantly when the thickness of the carbon nanofilm increases.When the carbon nanofilm accounts for 16%of the total thickness,the overall conductivity increases up to 30.20%compared to pure copper.The mechanism of the enhanced conductivity is analyzed including roles of copper atom adsorption sites and electron migration pathways by applying effective medium theory,first-principles calculations and density of states analysis.Under an applied electric field,the high-density electrons in the copper film can migrate into the nanocarbon film,forming highly efficient electron transport channels,which significantly enhance the material’s conductivity.Finally,large-area electrode coating equipment is developed based on this study,providing the novel and robust strategy to enhance the conductivity of copper materials,which enables industrial application of copper-carbon nanocomposite films in the field of high conductivity materials.展开更多
The geological structure of coal seams in China is remarkably varied and complex,with coalbed methane reservoirs marked by significant heterogeneity and low permeability,creating substantial technical challenges for e...The geological structure of coal seams in China is remarkably varied and complex,with coalbed methane reservoirs marked by significant heterogeneity and low permeability,creating substantial technical challenges for efficient extraction.This study systematically investigates the impact of liquid nitrogen immersion(LNI)on the coal’s pore structure and its mechanism of enhancing permeability with a combination of quantitative nuclear magnetic resonance(NMR)analysis,nitrogen adsorption experiments,and fractal dimension calculations.The results demonstrate that LNI can damage the coal’s pore structure and promote fracture expansion through thermal stress induction and moisture phase transformation,thereby enhancing the permeability of coal seams.The T_(2)peak area in the NMR experiments on coal samples subjected to LNI treatment shows a significant increase,the Brunauer-Emmett-Teller(BET)specific surface area decreases to 6.02 m^(2)/g,and the Barrett-Joyner-Halenda(BJH)total pore volume increases to 14.99 mm^(3)/g.Furthermore,changes in fractal dimensions(D_(1)rising from 2.804 to 2.837,and D_(2)falling from 2.757 to 2.594)indicate a notable enhancement in the complexity of the pore structure.With increasing LNI cycles,the adsorption capacity of the coal samples diminishes,suggesting a significant optimization of the pore structure.This optimization is particularly evident in the reconstruction of the micropore structure,which in turn greatly enhances the complexity and connectivity of the sample’s pore network.In summary,the study concludes that LNI technology can effectively improve the permeability of coal seams and the extraction efficiency of coalbed methane by optimizing the micropore structure and enhancing pore connectivity,which offers a potential method for enhancing the permeability of gas-bearing coal seams and facilitating the development and utilization of coalbed methane.展开更多
A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fractu...A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fracture surface of Al/Cu joints were studied by scanning electron microscopy（SEM） and X-ray diffraction（XRD）.The mechanical properties of the Al/Cu bimetals were measured by tensile shear and microhardness tests.The results show that the Ni interiayer can effectively eliminate the formation of Al-Cu intermetallic compounds.The Al/Ni interface consists of the Al3Ni and Al3Ni2 phases,while it is Ni-Cu solid solution at the Ni/Cu interce.The tensile shear strength of the joints is improved by the addition of Ni interiayer.The joint with Ni interiayer annealed at 500 ℃ exhibits a maximum value of tensile shear strength of 34.7 MPa.展开更多
Numerical simulations were conducted on a 10-blade Sevik rotor ingesting wake downstream of two turbulence-generating grids.These simulations were based on implicit large-eddy simulation(ILES)and the boundary data imm...Numerical simulations were conducted on a 10-blade Sevik rotor ingesting wake downstream of two turbulence-generating grids.These simulations were based on implicit large-eddy simulation(ILES)and the boundary data immersion method(BDIM)for compressible flows,which were solved using a fully self-programmed Fortran code.Results show that the predicted thrust spectrum aligns closely with the experimental measurements.In addition,it captures the thrust dipole directivity of the noise around the rotating propeller due to random pressure pulsations on the blades,as well as the flow structures simultaneously.Furthermore,the differences in the statistical characteristics,flow structures,and low-frequency broadband thrust spectra due to different turbulence levels were investigated.This analysis indicates that the interaction between the upstream,which is characterized by a lower turbulence level and a higher turbulent length of scale,and the rotating propeller results in a lower amplitude in force spectra and a slight increase in the scale of tip vortices.展开更多
A1 and N were introduced into copper substrate using plasma immersion ion implantation （PIII） in order to enhance its hardness and oxidation resistance. The dosage of N ion is 5 × 1016 cm-2, and range of dosage...A1 and N were introduced into copper substrate using plasma immersion ion implantation （PIII） in order to enhance its hardness and oxidation resistance. The dosage of N ion is 5 × 1016 cm-2, and range of dosage of A1 ion is 5× 1016-2× 1017 cm-2. The oxidation tests indicate that the copper samples after undergoing PIII possess higher oxidation resistance. The degree of oxidation resistance is found to vary with implantation dosage of AI ion. The antibacterial tests also reveal that the plasma implanted copper specimens have excellent antibacterial resistance against Staphylococcus aureus, which are similar to pure copper.展开更多
Colonoscopy techniques combining or replacing air insufflation with water infusion are becoming increasinglypopular.They were originally designed to reduce colonic spasms,facilitate cecal intubation,and lower patient ...Colonoscopy techniques combining or replacing air insufflation with water infusion are becoming increasinglypopular.They were originally designed to reduce colonic spasms,facilitate cecal intubation,and lower patient discomfort and the need for sedation.These maneuvers straighten the rectosigmoid colon and enable the colonoscope to be inserted deeply without causing looping of the colon.Water-immersion colonoscopy minimizes colonic distension and improves visibility by introducing a small amount of water.In addition,since pain during colonoscopy indicates risk of bowel perforation and sedation masks this important warning,this method has the potential to be the favored insertion technique because it promotes patient safety without sedation.Recently,this water-immersion method has not only been used for colonoscope insertion,but has also been applied to therapy for sigmoid volvulus,removal of lesions,lower gastrointestinal bleeding,and therapeutic diagnosis of abnormal bowel morphology and irritable bowel syndrome.Although a larger sample size and prospective head-to-head-designed studies will be needed,this review focuses on the usefulness of waterimmersion colonoscopy for diagnostic and therapeutic applications.展开更多
A submanifold in a complex space form is called slant if it has constant Wirtinger angles. B. Y. Chen and Y. Tazawa proved that there do not exist minimal proper slant surfaces in CP2 and CH2. So it seems that the sla...A submanifold in a complex space form is called slant if it has constant Wirtinger angles. B. Y. Chen and Y. Tazawa proved that there do not exist minimal proper slant surfaces in CP2 and CH2. So it seems that the slant immersion has some interesting properties. The authors have great interest to consider slant immersions satisfying some additional conditions, such as unfull first normal bundles or Chen’s equality holding. They prove that there do not exist n-dimensional Kaehlerian slant immersions in CPn and CHn with unfull first normal bundles. Next, it is seen that every Kaehlerian slant submanifold satisfying an equality of Chen is minimal which is similar to that of Lagrangian immersions. But in contrast, it is shown that a large class of slant immersions do not exist thoroughly. Finally, they give an application of Chen’s inequality to general slant immersions in a complex projective space, which generalizes a result of Chen.展开更多
This paper reports the comparative evaluation of the corrosion behaviour of AZ31B magnesium alloy under immersion and potentiodynamic polarization test in NaCl solution at different chloride ion concentrations,pH valu...This paper reports the comparative evaluation of the corrosion behaviour of AZ31B magnesium alloy under immersion and potentiodynamic polarization test in NaCl solution at different chloride ion concentrations,pH value and exposure time.The specimens were exposed to immersion and polarization environments in order to evaluate their corrosion rates.Empirical relationship was established to predict the corrosion rate of AZ31B magnesium alloy.Three factors,five level,central composite rotatable design matrix was used to minimize the number of experimental conditions.Response surface methodology was used to develop the relationship.The developed relationship can be effectively used to predict the corrosion rate of AZ31B magnesium alloy at 95%confidence level for both the testing.This research work proves a better corrosion resistance of AZ31B magnesium alloy at the alkaline solution than the acidic and the neutral solutions,moreover,low corrosion rate was found at low concentrated solution and higher exposure time respectively.展开更多
AIM:To evaluate the accuracy of axial length(AL)measurements obtained from immersion B-scan ultrasonography(immersion B-scan)for intraocular lens(IOL)power calculation in patients with high myopia and cataracts.METHOD...AIM:To evaluate the accuracy of axial length(AL)measurements obtained from immersion B-scan ultrasonography(immersion B-scan)for intraocular lens(IOL)power calculation in patients with high myopia and cataracts.METHODS:Immersion B-scan,contact A-scan ultrasonography(contact A-scan),and the IOLMaster were used to preoperatively measure the AL in 102 eyes from 102 patients who underwent phacoemulsification and IOL implantation.Patients were divided into two groups according to the AL:one containing patients with22 mm≤AL【26 mm(group A)and the other containing patients with AL≥26 mm(group B).The mean error(ME)was calculated from the difference between the AL measurement methods predicted refractive error and the actual postoperative refractive error.RESULTS:Ingroup A,ALs measured byimmersion Bscan(23.48±1.15)didn’t differ significantly from those measured by the IOLMaster(23.52±1.17)or from those by contact A-scan(23.38±1.20).In the same group,the standard deviation(SD)of the mean error(ME)of immersion B-scan(-0.090±0.397 D)didn’t differ significantly from those of IOLMaster(-0.095±0.411 D)and contact A-scan(-0.099±0.425 D).In group B,ALs measured by immersion B-scan(27.97±2.21 mm)didn’t differ significantly from those of the IOLMaster(27.86±2.18 mm),but longer than those measured by Contact A-scan(27.75±2.23 mm,P=0.009).In the same group,the standard deviation(SD)of the mean error(ME)of immersion B-scan(-0.635±0.157 D)didn’t differ significantly from those of the IOLMaster(-0.679±0.359 D),but differed significantly from those of contact A-scan(-0.953±1.713 D,P=0.028).CONCLUSION:ImmersionB-scanexhibitsmeasurement accuracy comparable to that of the IOLMaster,and is thus a good alternative in measuring AL in eyes with high myopia when the IOLMaster can’t be used,and it is more accurate than the contact A-scan.展开更多
The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface...The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.展开更多
Silver has grown its attraction of the scientists in microelectronic field recently.Electrochemical deposition of silver onto copper substrates by immersion method has been one of the keen topics. In this study, ethan...Silver has grown its attraction of the scientists in microelectronic field recently.Electrochemical deposition of silver onto copper substrates by immersion method has been one of the keen topics. In this study, ethanol was used as the plating solution in which some chemicals were added. The silver deposits were characterized by a field emission scanning electron microscopy （FESEM）, an atom force microscope （AFM）, a transmission electron microscope （TEM） and a selected area electron diffraction （SAED）. It was found that silver immersion using ethanol-based bath has good coverage feature. The highlands of the copper substrate are coated by silver particles whose sizes are around 12 nm, but those sizes at low-lying lands are a little smaller.展开更多
Plasma immersion ion implantation (PIII), unrestricted by sight-light process, is considered a proper method for inner surface strengthening. Two-dimensional simulation oj inner surface PIII process of cylindrical bo...Plasma immersion ion implantation (PIII), unrestricted by sight-light process, is considered a proper method for inner surface strengthening. Two-dimensional simulation oj inner surface PIII process of cylindrical bores were carried out in this paper using cold plasma fluid model, and influence of the bore's dimension on impact energy, retained dose and uniformity of inner surface were investigated.展开更多
Background: Wounded personnel who work at sea often encounter a plethora of difficulties. The most important of these difficulties is seawater immersion. Common medical dressings have little effect when the affected a...Background: Wounded personnel who work at sea often encounter a plethora of difficulties. The most important of these difficulties is seawater immersion. Common medical dressings have little effect when the affected area is immersed in seawater, and only rarely dressings have been reported for the treatment of seawater-immersed wounds. The objective of this study is to develop a new dressing which should be suitable to prevent the wound from seawater immersion and to promote the wound healing.Methods: Shark skin collagen(SSC) was purified via ethanol de-sugaring and de-pigmentation and adjusted for p H. A shark skin collagen sponge(SSCS) was prepared by freeze-drying. SSCS was attached to an anti-seawater immersion polyurethane(PU) film(SSCS+PU) to compose a new dressing. The biochemical properties of SSC and physicochemical properties of SSCS were assessed by standard methods. The effects of SSCS and SSCS+PU on the healing of seawaterimmersed wounds were studied using a seawater immersion rat model. For the detection of SSCS effects on seawaterimmersed wounds, 12 SD rats, with four wounds created in each rat, were divided into four groups: the 3 rd day group, 5 th day group, 7 th day group and 12 th day group. In each group, six wounds were treated with SSCS, three wounds treated with chitosan served as the positive control, and three wounds treated with gauze served as the negative control. For the detection of the SSCS+PU effects on seawater-immersed wounds, 36 SD rats were divided into three groups: the gauze(GZ)+PU group, chitosan(CS)+PU group and SSCS+PU group, with 12 rats in each group, and two wounds in each rat. The wound sizes were measured to calculate the healing rate, and histomorphology and the immunohistochemistry of the CD31 and TGF-β expression levels in the wounded tissues were measured by standard methods.Results: The results of Ultraviolet-visible(UV-vis) spectrum, Fourier-transform infrared(FTIR) spectrum, circular dichroism(CD) spectra, sodium dodecyl sulfate polyacrylamide gel electrophoresis(SDS-PAGE), and amino acid composition analyses of SSC demonstrated that SSC is type I collagen. SSCS had a homogeneous porous structure of approximately 200μm, porosity rate of 83.57%±2.64%, water vapor transmission ratio(WVTR) of 4500 g/m2, tensile strength of 1.79±0.41 N/mm, and elongation at break of 4.52%±0.01%. SSCS had significant beneficial effects on seawater-immersed wound healing. On the 3 rd day, the healing rates in the GZ negative control, CS positive control and SSCS rats were 13.94%±5.50%, 29.40%±1.10% and 47.24%±8.40%, respectively. SSCS also enhanced TGF-in the initial stage of the healing period. The SSCS+PU dressing effectively protected woundsβ and CD31 expression from seawater immersion for at least 4 h, and accelerated re-epithelialization, vascularization and granulation formation of seawater-immersed wounds in the earlier stages of wound healing, and as well as significantly promoted wound healing. The SSCS+PU dressing also enhanced expression of TGF-n and gauze dressings.β and CD31. The effects of SSCS and SSCS+PU were superior to those of both the chitosaConclusion: SSCS has significant positive effects on the promotion of seawater-immersed wound healing, and a SSCS+PU dressing effectively prevents seawater immersion, and significantly promotes seawater-immersed wound healing.展开更多
The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe product...The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe production.The impact compression tests were performed on coal with diferent moisture contents by using theϕ50 mm Split Hopkinson Pressure Bar(SHPB)experimental system,and the dynamic characteristics and energy loss laws of water-immersed coal with diferent compositions and water contents were analyzed.Through analysis and discussion,it is found that:(1)When the moisture content of the coal sample is 0%,30%,60%,the stress,strain rate and energy frst increase and then decrease with time.(2)When the moisture content of the coal sample increases from 30%to 60%,the stress“plateau”of the coal sample becomes more obvious,resulting in an increase in the compressive stress stage and a decrease in the expansion stress stage.(3)The increase of moisture content of the coal sample will afect its impact deformation and failure mode.When the moisture content is 60%,the incident rod end and the transmission rod end of the coal sample will have obvious compression failure,and the middle part of the coal sample will also experience expansion and deformation.(4)The coal composition ratio suitable for the coal immersion softening impact experiment is optimized.展开更多
Data centers are recognized as one of the most important aspects of the fourth industrial revolution since conventional data centers are inefficient and have dependency on high energy consumption,in which the cooling ...Data centers are recognized as one of the most important aspects of the fourth industrial revolution since conventional data centers are inefficient and have dependency on high energy consumption,in which the cooling is responsible for 40%of the usage.Therefore,this research proposes the immersion cooling method to solving the high energy consumption of data centers by cooling its component using two types of dielectric fluids.Four stages of experimentalmethods are used,such as fluid types,cooling effectiveness,optimization,and durability.Furthermore,benchmark software is used to measure the CPU maximum work with the temperature data performed for 24 h.The results of this study show that the immersion cooling reduces 13℃ lower temperature than the conventional cooling method which means it saves more energy consumption in the data center.The most optimum variable used to decrease the temperature is 1.5 lpm of flow rate and 800 rpm of fan rotation.Furthermore,the cooling performance of the dielectric fluids shows that the mineral oil(MO)is better than the virgin coconut oil(VCO).In durability experiment,there are no components damage after five months immersed in the fluid.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52474133,52304227,52304091,and 52374095)the Natural Science Foundation of Hunan Province(Nos.2025JJ50316 and 2023JJ40548).
文摘To investigate the influence of non-uniform water distribution on the mechanical properties and failure behavior of red sandstone,we designed five immersion heights and durations to achieve varying non-uniform water distribution states.Uniaxial compression tests were conducted on red sandstone under these conditions.The effects of non-uniform water distribution on deformation,failure,strength,and energy characteristics of red sandstone were analyzed.The impact of non-uniform water distribution on the intensity of rock failure was discussed,and the failure mechanism under non-uniform water distribution was revealed.The hazards of low immersion heights on underground rock structures were analyzed.The results demonstrate that peak strength and elastic modulus of red sandstone exhibit high sensitivity to immersion height,with reductions of 38%and 23%respectively even at L=1/50H.Water immersion reduces both energy storage capacity and energy dissipation capability of red sandstone.The immersion height and duration influence the failure mode of red sandstone by controlling the migration and separation of dry-wet interfaces.Low immersion height poses significant risks to underground rock structures(e.g.,a 38%strength reduction when L=1/50H),and the concentration degree of water non-uniform distribution is the key factor in assessing the weakening effect of water on rocks.
基金funding support from the National Natural Science Foundation of China(Grant No.12172019).
文摘In cold regions,rock structures will be weakened by freeze-thaw cycles under various water immersion conditions.Determining how water immersion conditions impact rock deterioration under freeze-thaw cycles is critical to assess accurately the frost resistance of engineered rock.In this paper,freeze-thaw cycles(temperature range of-20℃-20℃)were performed on the sandstones in different water immersion conditions(fully,partially and non-immersed in water).Then,computed tomography(CT)tests were conducted on the sandstones when the freeze-thaw number reached 0,5,10,15,20 and 30.Next,the effects of water immersion conditions on the microstructure deterioration of sandstone under freezethaw cycles were evaluated using CT spatial imaging,porosity and damage factor.Finally,focusing on the partially immersed condition,the immersion volume rate was defined to understand the effects of immersion degree on the freeze-thaw damage of sandstone and to propose a damage model considering the freeze-thaw number and immersion degree.The results show that with increasing freeze-thaw number,the porosities and damage factors under fully and partially immersed conditions increase continuously,while those under non-immersed condition first increase and then remain approximately constant.The most severe freeze-thaw damage occurs in fully immersed condition,followed by partially immersed condition and finally non-immersed condition.Interestingly,the freeze-thaw number and the immersion volume rate both impact the microstructure deterioration of the partially immersed sandstone.For the same freeze-thaw number,the damage factor increases approximately linearly with increasing immersion volume rate,and the increasing immersion degree exacerbates the microstructure deterioration of sandstone.Moreover,the proposed model can effectively estimate the freeze-thaw damage of partially immersed sandstone with different immersion volume rates.
文摘This study focuses on the thermal management of 4680-type cylindrical lithium-ion battery packs utilizing NCM811 chemistry.It establishes coupled multi-physics models for both immersion and serpentine cold plate cooling systems.Through a combination of numerical simulation and experimental validation,the technical advantages and mechanisms of immersion cooling are systematically explored.Simulation results indicate that under a 3C fast-charging condition(inlet temperature 20℃,flow rate 36 L/min),the immersion cooling structure 3demonstrates a triple enhancement in thermal performance compared to the cold plate structure 1:a 13.06%reduction in peak temperature,a 31.67%decrease in overall maximum temperature difference,and a 47.62%decrease in single-cell temperature deviation,while also reducing flow resistance by 33.61%.Furthermore,based on the immersion cooling model,a small battery module comprising seven cylindrical cells was designed for thermal runaway testing via nail penetration.The results show that the peak temperature of the triggered cell was limited to 437.6℃,with a controllable temperature rise gradient of only 3.35℃/s and a rapid cooling rate of 0.6℃/s.The maximum temperature rise of adjacent cells was just 64.8℃,effectively inhibiting thermal propagation.Post-test disassembly revealed that the non-triggered cells retained>99.2%of their original voltage and>99%structural integrity,confirming the module’s ability to achieve“localized failure with global stability.”
基金supported by CAPES scholarship-Brazil Coordination for the Improvement of Higher Education Personnel(No.88887.507764/2020-00)]by CNPq-Brazil National Council of Technological and Scientific Development(No.308564/2023-5).
文摘The self-healing properties of dual-component epoxy microcapsules are evaluated when incorporated into an epoxy coating.The performance of the coating was assessed under immersion in a saline solution,simulating seawater conditions.Initially,synthesized microcapsules are incorporated into the epoxy coating.Then,the self-healing capabilities of the coating are studied under immersion using scanning vibrating electrode technique(SVET),open circuit potential(OCP),electrochemical impedance spectroscopy(EIS)and immersion corrosion test on coated samples with intentionally created artificial defects.The last three tests were conducted in a 3.5%NaCl solution.The adhesion of the coating is also studied by pull-off adhesion test.SVET analyses reveal lower ionic current densities in coated samples containing microcapsules during 24 h of immersion.EIS results demonstrate self-healing at the defect site for up to 12 h of immersion.After this time,the corrosion protection diminishes with prolonged immersion in the saline solution.Despite this,the coating with the microcapsules exhibits decrease in the corrosion process compared to the coating without the microcapsules.These results are consistent and complement the outcomes of the immersion tests conducted over 360 and 1056 h,which indicate that coated samples without microcapsules exhibit double the corroded areas around the scribes compared to coated samples containing the microcapsules.These findings offer a promising outlook for applying this coating on offshore carbon steel structures under immersion aiming for a longer lifetime with less maintenance intervention.
文摘The challenge of effectively eliminating air during gastrointestinal endoscopy using ultrasound techniques is apparent.This difficulty arises from the intricacies of removing concealed air within the folds of the gastrointestinal tract,resulting in artifacts and compromised visualization.In addition,the overlap of folds with lesions can obscure their depth and size,presenting challenges for an accurate assessment.Conversely,in intricately folded regions of the gastrointestinal tract,such as the stomach,intestine,and colon,insufficient delivery of air or CO_(2) into the cavity impedes luminal expansion,hindering the accurate visualization of lesions concealed within the folds.Although this underscores the requirement for substantial airflow,excessive airflow can hinder visualization of bleeding lesions and other abnormalities.Considering these challenges,an ideal endoscopic device would facilitate the observation of lesions without the requirement for air or CO_(2) delivery whereas,ensuring optimal expansion of the gastrointestinal tract.Recently,transparent gels with specific viscosities have been employed more frequently to address this issue.This review aims to elucidate how these gels address these challenges and provide a solution for enhanced endoscopic visualization.
基金support from the National Natural Science Foundation of China(61574091)National Natural Science Foundation of China Key Program(50730008).
文摘Although room-temperature superconductivity is still difficult to achieve,researching materials with electrical conductivity significantly higher than that of copper will be of great importance in improving energy efficiency,reducing costs,lightening equipment weight,and enhancing overall performance.Herein,this study presents a novel copper-carbon nanofilm composite with enhanced conductivity which has great applications in the electronic devices and electrical equipment.Multilayer copper-carbon nanofilms and interfaces with superior electronic structures are formed based on copper materials using plasma immersion nanocarbon layer deposition technology,effectively enhancing conductivity.Experimental results show that for a five-layer copper-carbon nanofilm composite,the conductivity improves significantly when the thickness of the carbon nanofilm increases.When the carbon nanofilm accounts for 16%of the total thickness,the overall conductivity increases up to 30.20%compared to pure copper.The mechanism of the enhanced conductivity is analyzed including roles of copper atom adsorption sites and electron migration pathways by applying effective medium theory,first-principles calculations and density of states analysis.Under an applied electric field,the high-density electrons in the copper film can migrate into the nanocarbon film,forming highly efficient electron transport channels,which significantly enhance the material’s conductivity.Finally,large-area electrode coating equipment is developed based on this study,providing the novel and robust strategy to enhance the conductivity of copper materials,which enables industrial application of copper-carbon nanocomposite films in the field of high conductivity materials.
基金Projects(52204226,52104204,52474276)supported by the National Natural Science Foundation of ChinaProject(tsqnz20221140)supported by the Taishan Scholars Project of China+1 种基金Projects(ZR2022QE243,ZR2024ME097)supported by the Natural Science Foundation of Shandong Province of ChinaProject(252300421010)supported by the Excellent Youth Foundation of Henan Scientific Committee,China。
文摘The geological structure of coal seams in China is remarkably varied and complex,with coalbed methane reservoirs marked by significant heterogeneity and low permeability,creating substantial technical challenges for efficient extraction.This study systematically investigates the impact of liquid nitrogen immersion(LNI)on the coal’s pore structure and its mechanism of enhancing permeability with a combination of quantitative nuclear magnetic resonance(NMR)analysis,nitrogen adsorption experiments,and fractal dimension calculations.The results demonstrate that LNI can damage the coal’s pore structure and promote fracture expansion through thermal stress induction and moisture phase transformation,thereby enhancing the permeability of coal seams.The T_(2)peak area in the NMR experiments on coal samples subjected to LNI treatment shows a significant increase,the Brunauer-Emmett-Teller(BET)specific surface area decreases to 6.02 m^(2)/g,and the Barrett-Joyner-Halenda(BJH)total pore volume increases to 14.99 mm^(3)/g.Furthermore,changes in fractal dimensions(D_(1)rising from 2.804 to 2.837,and D_(2)falling from 2.757 to 2.594)indicate a notable enhancement in the complexity of the pore structure.With increasing LNI cycles,the adsorption capacity of the coal samples diminishes,suggesting a significant optimization of the pore structure.This optimization is particularly evident in the reconstruction of the micropore structure,which in turn greatly enhances the complexity and connectivity of the sample’s pore network.In summary,the study concludes that LNI technology can effectively improve the permeability of coal seams and the extraction efficiency of coalbed methane by optimizing the micropore structure and enhancing pore connectivity,which offers a potential method for enhancing the permeability of gas-bearing coal seams and facilitating the development and utilization of coalbed methane.
基金Projects (51274054,51375070,51271042) supported by the National Natural Science Foundation of ChinaProjects (2013M530913) supported by the China Postdoctoral Science Foundation
文摘A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fracture surface of Al/Cu joints were studied by scanning electron microscopy（SEM） and X-ray diffraction（XRD）.The mechanical properties of the Al/Cu bimetals were measured by tensile shear and microhardness tests.The results show that the Ni interiayer can effectively eliminate the formation of Al-Cu intermetallic compounds.The Al/Ni interface consists of the Al3Ni and Al3Ni2 phases,while it is Ni-Cu solid solution at the Ni/Cu interce.The tensile shear strength of the joints is improved by the addition of Ni interiayer.The joint with Ni interiayer annealed at 500 ℃ exhibits a maximum value of tensile shear strength of 34.7 MPa.
基金Supported by the National Key R&D Program of China(2022YFB3303500).
文摘Numerical simulations were conducted on a 10-blade Sevik rotor ingesting wake downstream of two turbulence-generating grids.These simulations were based on implicit large-eddy simulation(ILES)and the boundary data immersion method(BDIM)for compressible flows,which were solved using a fully self-programmed Fortran code.Results show that the predicted thrust spectrum aligns closely with the experimental measurements.In addition,it captures the thrust dipole directivity of the noise around the rotating propeller due to random pressure pulsations on the blades,as well as the flow structures simultaneously.Furthermore,the differences in the statistical characteristics,flow structures,and low-frequency broadband thrust spectra due to different turbulence levels were investigated.This analysis indicates that the interaction between the upstream,which is characterized by a lower turbulence level and a higher turbulent length of scale,and the rotating propeller results in a lower amplitude in force spectra and a slight increase in the scale of tip vortices.
基金Project(9231083) supported by Yunnan Aerospace Industry Corporation Contract Research,ChinaProject(9220061) supported by City University of Hong Kong Donation Research Grant,China
文摘A1 and N were introduced into copper substrate using plasma immersion ion implantation （PIII） in order to enhance its hardness and oxidation resistance. The dosage of N ion is 5 × 1016 cm-2, and range of dosage of A1 ion is 5× 1016-2× 1017 cm-2. The oxidation tests indicate that the copper samples after undergoing PIII possess higher oxidation resistance. The degree of oxidation resistance is found to vary with implantation dosage of AI ion. The antibacterial tests also reveal that the plasma implanted copper specimens have excellent antibacterial resistance against Staphylococcus aureus, which are similar to pure copper.
文摘Colonoscopy techniques combining or replacing air insufflation with water infusion are becoming increasinglypopular.They were originally designed to reduce colonic spasms,facilitate cecal intubation,and lower patient discomfort and the need for sedation.These maneuvers straighten the rectosigmoid colon and enable the colonoscope to be inserted deeply without causing looping of the colon.Water-immersion colonoscopy minimizes colonic distension and improves visibility by introducing a small amount of water.In addition,since pain during colonoscopy indicates risk of bowel perforation and sedation masks this important warning,this method has the potential to be the favored insertion technique because it promotes patient safety without sedation.Recently,this water-immersion method has not only been used for colonoscope insertion,but has also been applied to therapy for sigmoid volvulus,removal of lesions,lower gastrointestinal bleeding,and therapeutic diagnosis of abnormal bowel morphology and irritable bowel syndrome.Although a larger sample size and prospective head-to-head-designed studies will be needed,this review focuses on the usefulness of waterimmersion colonoscopy for diagnostic and therapeutic applications.
基金This project is supported by the NSFC(10271041)Tianyuan Youth Foundation of Mathematics.
文摘A submanifold in a complex space form is called slant if it has constant Wirtinger angles. B. Y. Chen and Y. Tazawa proved that there do not exist minimal proper slant surfaces in CP2 and CH2. So it seems that the slant immersion has some interesting properties. The authors have great interest to consider slant immersions satisfying some additional conditions, such as unfull first normal bundles or Chen’s equality holding. They prove that there do not exist n-dimensional Kaehlerian slant immersions in CPn and CHn with unfull first normal bundles. Next, it is seen that every Kaehlerian slant submanifold satisfying an equality of Chen is minimal which is similar to that of Lagrangian immersions. But in contrast, it is shown that a large class of slant immersions do not exist thoroughly. Finally, they give an application of Chen’s inequality to general slant immersions in a complex projective space, which generalizes a result of Chen.
文摘This paper reports the comparative evaluation of the corrosion behaviour of AZ31B magnesium alloy under immersion and potentiodynamic polarization test in NaCl solution at different chloride ion concentrations,pH value and exposure time.The specimens were exposed to immersion and polarization environments in order to evaluate their corrosion rates.Empirical relationship was established to predict the corrosion rate of AZ31B magnesium alloy.Three factors,five level,central composite rotatable design matrix was used to minimize the number of experimental conditions.Response surface methodology was used to develop the relationship.The developed relationship can be effectively used to predict the corrosion rate of AZ31B magnesium alloy at 95%confidence level for both the testing.This research work proves a better corrosion resistance of AZ31B magnesium alloy at the alkaline solution than the acidic and the neutral solutions,moreover,low corrosion rate was found at low concentrated solution and higher exposure time respectively.
基金Supported by National Key Basic Research Program of China(973 Program,No.2013CB967000)National Natural Science Foundation of China(No.81271052)
文摘AIM:To evaluate the accuracy of axial length(AL)measurements obtained from immersion B-scan ultrasonography(immersion B-scan)for intraocular lens(IOL)power calculation in patients with high myopia and cataracts.METHODS:Immersion B-scan,contact A-scan ultrasonography(contact A-scan),and the IOLMaster were used to preoperatively measure the AL in 102 eyes from 102 patients who underwent phacoemulsification and IOL implantation.Patients were divided into two groups according to the AL:one containing patients with22 mm≤AL【26 mm(group A)and the other containing patients with AL≥26 mm(group B).The mean error(ME)was calculated from the difference between the AL measurement methods predicted refractive error and the actual postoperative refractive error.RESULTS:Ingroup A,ALs measured byimmersion Bscan(23.48±1.15)didn’t differ significantly from those measured by the IOLMaster(23.52±1.17)or from those by contact A-scan(23.38±1.20).In the same group,the standard deviation(SD)of the mean error(ME)of immersion B-scan(-0.090±0.397 D)didn’t differ significantly from those of IOLMaster(-0.095±0.411 D)and contact A-scan(-0.099±0.425 D).In group B,ALs measured by immersion B-scan(27.97±2.21 mm)didn’t differ significantly from those of the IOLMaster(27.86±2.18 mm),but longer than those measured by Contact A-scan(27.75±2.23 mm,P=0.009).In the same group,the standard deviation(SD)of the mean error(ME)of immersion B-scan(-0.635±0.157 D)didn’t differ significantly from those of the IOLMaster(-0.679±0.359 D),but differed significantly from those of contact A-scan(-0.953±1.713 D,P=0.028).CONCLUSION:ImmersionB-scanexhibitsmeasurement accuracy comparable to that of the IOLMaster,and is thus a good alternative in measuring AL in eyes with high myopia when the IOLMaster can’t be used,and it is more accurate than the contact A-scan.
文摘The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.
基金Supported by the Key Project Foundation of Fujian Province (No. 200I011)
文摘Silver has grown its attraction of the scientists in microelectronic field recently.Electrochemical deposition of silver onto copper substrates by immersion method has been one of the keen topics. In this study, ethanol was used as the plating solution in which some chemicals were added. The silver deposits were characterized by a field emission scanning electron microscopy （FESEM）, an atom force microscope （AFM）, a transmission electron microscope （TEM） and a selected area electron diffraction （SAED）. It was found that silver immersion using ethanol-based bath has good coverage feature. The highlands of the copper substrate are coated by silver particles whose sizes are around 12 nm, but those sizes at low-lying lands are a little smaller.
文摘Plasma immersion ion implantation (PIII), unrestricted by sight-light process, is considered a proper method for inner surface strengthening. Two-dimensional simulation oj inner surface PIII process of cylindrical bores were carried out in this paper using cold plasma fluid model, and influence of the bore's dimension on impact energy, retained dose and uniformity of inner surface were investigated.
基金supported by a Major Project of the Ministry of National Science and Technology of China(Grant No.2014ZX09J14103-09C).
文摘Background: Wounded personnel who work at sea often encounter a plethora of difficulties. The most important of these difficulties is seawater immersion. Common medical dressings have little effect when the affected area is immersed in seawater, and only rarely dressings have been reported for the treatment of seawater-immersed wounds. The objective of this study is to develop a new dressing which should be suitable to prevent the wound from seawater immersion and to promote the wound healing.Methods: Shark skin collagen(SSC) was purified via ethanol de-sugaring and de-pigmentation and adjusted for p H. A shark skin collagen sponge(SSCS) was prepared by freeze-drying. SSCS was attached to an anti-seawater immersion polyurethane(PU) film(SSCS+PU) to compose a new dressing. The biochemical properties of SSC and physicochemical properties of SSCS were assessed by standard methods. The effects of SSCS and SSCS+PU on the healing of seawaterimmersed wounds were studied using a seawater immersion rat model. For the detection of SSCS effects on seawaterimmersed wounds, 12 SD rats, with four wounds created in each rat, were divided into four groups: the 3 rd day group, 5 th day group, 7 th day group and 12 th day group. In each group, six wounds were treated with SSCS, three wounds treated with chitosan served as the positive control, and three wounds treated with gauze served as the negative control. For the detection of the SSCS+PU effects on seawater-immersed wounds, 36 SD rats were divided into three groups: the gauze(GZ)+PU group, chitosan(CS)+PU group and SSCS+PU group, with 12 rats in each group, and two wounds in each rat. The wound sizes were measured to calculate the healing rate, and histomorphology and the immunohistochemistry of the CD31 and TGF-β expression levels in the wounded tissues were measured by standard methods.Results: The results of Ultraviolet-visible(UV-vis) spectrum, Fourier-transform infrared(FTIR) spectrum, circular dichroism(CD) spectra, sodium dodecyl sulfate polyacrylamide gel electrophoresis(SDS-PAGE), and amino acid composition analyses of SSC demonstrated that SSC is type I collagen. SSCS had a homogeneous porous structure of approximately 200μm, porosity rate of 83.57%±2.64%, water vapor transmission ratio(WVTR) of 4500 g/m2, tensile strength of 1.79±0.41 N/mm, and elongation at break of 4.52%±0.01%. SSCS had significant beneficial effects on seawater-immersed wound healing. On the 3 rd day, the healing rates in the GZ negative control, CS positive control and SSCS rats were 13.94%±5.50%, 29.40%±1.10% and 47.24%±8.40%, respectively. SSCS also enhanced TGF-in the initial stage of the healing period. The SSCS+PU dressing effectively protected woundsβ and CD31 expression from seawater immersion for at least 4 h, and accelerated re-epithelialization, vascularization and granulation formation of seawater-immersed wounds in the earlier stages of wound healing, and as well as significantly promoted wound healing. The SSCS+PU dressing also enhanced expression of TGF-n and gauze dressings.β and CD31. The effects of SSCS and SSCS+PU were superior to those of both the chitosaConclusion: SSCS has significant positive effects on the promotion of seawater-immersed wound healing, and a SSCS+PU dressing effectively prevents seawater immersion, and significantly promotes seawater-immersed wound healing.
基金This research was funded by the National Natural Science Foundation of China(51974176,51934004)ShandongProvince Natural Science Foundation of Outstanding Youth Fund(ZR2020JQ22)+1 种基金Shandong Province Colleges and Universities Youth Innovation and Technology Support Program(2019KJH006)Taishan Scholars Project(TS20190935).
文摘The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe production.The impact compression tests were performed on coal with diferent moisture contents by using theϕ50 mm Split Hopkinson Pressure Bar(SHPB)experimental system,and the dynamic characteristics and energy loss laws of water-immersed coal with diferent compositions and water contents were analyzed.Through analysis and discussion,it is found that:(1)When the moisture content of the coal sample is 0%,30%,60%,the stress,strain rate and energy frst increase and then decrease with time.(2)When the moisture content of the coal sample increases from 30%to 60%,the stress“plateau”of the coal sample becomes more obvious,resulting in an increase in the compressive stress stage and a decrease in the expansion stress stage.(3)The increase of moisture content of the coal sample will afect its impact deformation and failure mode.When the moisture content is 60%,the incident rod end and the transmission rod end of the coal sample will have obvious compression failure,and the middle part of the coal sample will also experience expansion and deformation.(4)The coal composition ratio suitable for the coal immersion softening impact experiment is optimized.
基金This work is financially supported by the Ministry of Research and Technology of Indonesia(BRIN)in the project called“Penggunaan Immersion Cooling untukMeningkatkan Efisiensi Energi Data Center”.
文摘Data centers are recognized as one of the most important aspects of the fourth industrial revolution since conventional data centers are inefficient and have dependency on high energy consumption,in which the cooling is responsible for 40%of the usage.Therefore,this research proposes the immersion cooling method to solving the high energy consumption of data centers by cooling its component using two types of dielectric fluids.Four stages of experimentalmethods are used,such as fluid types,cooling effectiveness,optimization,and durability.Furthermore,benchmark software is used to measure the CPU maximum work with the temperature data performed for 24 h.The results of this study show that the immersion cooling reduces 13℃ lower temperature than the conventional cooling method which means it saves more energy consumption in the data center.The most optimum variable used to decrease the temperature is 1.5 lpm of flow rate and 800 rpm of fan rotation.Furthermore,the cooling performance of the dielectric fluids shows that the mineral oil(MO)is better than the virgin coconut oil(VCO).In durability experiment,there are no components damage after five months immersed in the fluid.
