Metallic glass matrix composites(BMGCs)with compositions of[(Zr_(0.5)Cu_(0.5))_(0.925)Al_(0.07)Sn_(0.005)]_(100-x)Ta_(x)(atomic fraction,%,x=3,5,7)were successfully prepared via dealloying in metallic melt.The reinfor...Metallic glass matrix composites(BMGCs)with compositions of[(Zr_(0.5)Cu_(0.5))_(0.925)Al_(0.07)Sn_(0.005)]_(100-x)Ta_(x)(atomic fraction,%,x=3,5,7)were successfully prepared via dealloying in metallic melt.The reinforcing phase in these alloys has core-shell hybrid structure with Ta-rich particles as core and B2-CuZr as shell.In this method,the dealloyed Ta from Zr-Ta pre-alloys maintained in solid state and aggregated to form the fine Ta-rich phase in the final products.This effectively decreases the size of Ta-rich phase compared with that prepared via conventional arc-melting,where the Ta-rich phase was formed through dissolving and precipitation.Among the three compositions,[(Zr_(0.5)Cu_(0.5))_(0.925)Al_(0.07)Sn_(0.005)]_(95)Ta_(5) showed the highest plastic strain of 11.2%,much higher than that of the arc-melted counterparts(4.3%).Such improvement in mechanical properties was related with the refined core-shell hybrid reinforcing structure,which could hinder the rapid propagation of main shear band more efficiently and cause them to branch and proliferate at the interface.展开更多
Ultraviolet （UV） photodetector constructed by ZnO material has attracted intense research and commercial interest. However, its photoresistivity and photoresonse are still unsatisfied. Herein, we report a novel meth...Ultraviolet （UV） photodetector constructed by ZnO material has attracted intense research and commercial interest. However, its photoresistivity and photoresonse are still unsatisfied. Herein, we report a novel method to assemble ZnO nanoparticles （NPs） onto the reduced graphite oxide （RGO） sheet by simple hydrothermal process without any surfactant. It is found that the high-quality crystallized ZnO NPs with the average diameter of 5 nm are well dispersed on the RGO surface, and the density of ZnO NPs can be readily controlled by the concentration of the precursor. The photodetector fabricated with this ZnO NPs- RGO hybrid structure demonstrates an excellent photoresponse for the UV irradiation. The results make this hybrid especially suitable as a novel material for the design and fabrication of high performance UV photodector.展开更多
By integrating topology optimization and lattice-based optimization,a novel multi-scale design method is proposed to create solid-lattice hybrid structures and thus to improve the mechanical performance as well as red...By integrating topology optimization and lattice-based optimization,a novel multi-scale design method is proposed to create solid-lattice hybrid structures and thus to improve the mechanical performance as well as reduce the structural weight.To achieve this purpose,a two-step procedure is developed to design and optimize the innovative structures.Initially,the classical topology optimization is utilized to find the optimal material layout and primary load carrying paths.Afterwards,the solid-lattice hybrid structures are reconstructed using the finite element mesh based modeling method.And lattice-based optimization is performed to obtain the optimal crosssection area of the lattice structures.Finally,two typical aerospace structures are optimized to demonstrate the effectiveness of the proposed optimization framework.The numerical results are quite encouraging since the solid-lattice hybrid structures obtained by the presented approach show remarkably improved performance when compared with traditional designs.展开更多
A new design method for a water-reusing network, with a hybrid structure, to reduce the complexity of the network and to minimize freshwater consumption, is proposed. The unique feature of the methodology proposed .i...A new design method for a water-reusing network, with a hybrid structure, to reduce the complexity of the network and to minimize freshwater consumption, is proposed. The unique feature of the methodology proposed .in this article is to control the complexity of the water network by regulation of the control number in a water-reusing system. It combines the advantages of a conventional water-reusing network and a water-reusing net work with internal water mains. To illustrate the proposed method, a single contaminant system and a multiple contaminant system serve as examples of the problems.展开更多
Many single-tower reinforced concrete core wall-steel frame （RCC-SF） buildings have been built in China, but there are no buildings of different-height multi-tower hybrid system. A multi-tower RCC-SF tall building w...Many single-tower reinforced concrete core wall-steel frame （RCC-SF） buildings have been built in China, but there are no buildings of different-height multi-tower hybrid system. A multi-tower RCC-SF tall building was thus studied because of its structural complexity and irregularity. First, a 1/15 scaled model structure was designed and tested on the shake table under minor, moderate, and major earthquake levels. Then, the dynamic responses of the model structure were interpreted to those of the prototype structure according to the similitude theory. Experimental results demonstrate that, despite the complexity of the structure, the lateral deformation bends as the ＂bending type＂ and the RC core walls contribute more than the steel frames to resist seismic loads. The maximum inter-story drift of the complex building under minor earthquakes is slightly beyond the elastic limitation specified in the Chinese code, and meets code requirements under major earthquakes. From the test results some suggestions are provided that could contribute favorable effect on the seismic behavior and the displacement of the building.展开更多
Frame-masonry horizontal hybrid structure is a new type of self-built residence in the rural areas of Fujian Province in recent years. A shaking table test for 1/2 scale model is carried out on the basis of one repres...Frame-masonry horizontal hybrid structure is a new type of self-built residence in the rural areas of Fujian Province in recent years. A shaking table test for 1/2 scale model is carried out on the basis of one representative rural structure, and the dynamic characteristics and seismic responses of this experimental model are measured. As a supplement, the finite element model of the prototype structure is built by ANSYS software,and simulation and test results are contrasted and analyzed. The results show that according to this structure,the beam-column joint of the frame part has stress concentration and the destruction pattern of the masonry part is similar to brick-masonry structure. There are obvious differences in lateral stiffness of each floor and direction,and the mass center does not coincide with the stiffness center, which can lead to excessive torsion and story drift of this structure under earthquakes of a certain intensity. Because of poor construction quality, unfavorable structural measures and irrational structural system in present rural areas, there is a potential safety threat with this type of structures in highly seismic region. Some suggestions for strengthening and retrofitting frame-masonry horizontal hybrid structures are pointed out.展开更多
We report an extraordinary sound absorption enhancement in low and intermediate frequencies achieved by a thin multi-slit hybrid structure formed by incorporating micrometer scale micro-slits into a sub-millimeter sca...We report an extraordinary sound absorption enhancement in low and intermediate frequencies achieved by a thin multi-slit hybrid structure formed by incorporating micrometer scale micro-slits into a sub-millimeter scale meso-slit matrix. Theoretical and numerical results reveal that this exotic phenomenon is attributed to the noticeable velocity and temperature gradients induced at the junctures of the micro- and meso-slits, which cause significant loss of sound energy as a result of viscous and thermal effects. It is demonstrated that the proposed thin multi-slit hybrid structure with micro-scale configuration is capable of controling low frequency noise with large wavelength, which is attractive for applications where the size and weight of a sound absorber are restricted.展开更多
We report on the fabrication and performance of a room-temperature NO2 gas sensor based on a WO3 nanowires/porous silicon hybrid structure. The W18O49 nanowires are synthesized directly from a sputtered tungsten film ...We report on the fabrication and performance of a room-temperature NO2 gas sensor based on a WO3 nanowires/porous silicon hybrid structure. The W18O49 nanowires are synthesized directly from a sputtered tungsten film on a porous silicon （PS） layer under heating in an argon atmosphere. After a carefully controlled annealing treatment, WO3 nanowires are obtained on the PS layer without losing the morphology. The morphology, phase structure, and crystallinity of the nanowires are investigated by using field emission scanning electron microscopy （FESEM）, X-ray diffractometer （XRD）, and high-resolution transmission electron microscopy （HRTEM）. Comparative gas sensing results indicate that the sensor based on the WO3 nanowires exhibits a much higher sensitivity than that based on the PS and pure WO3 nanowires in detecting NO2 gas at room temperature. The mechanism of the WO3 nanowires/PS hybrid structure in the NO2 sensing is explained in detail.展开更多
With the increment of the complexity of structural systems and the span of spatial structures, the interactions between parts of the structures, especially between some flexible substructures, become too complex to be...With the increment of the complexity of structural systems and the span of spatial structures, the interactions between parts of the structures, especially between some flexible substructures, become too complex to be analyzed clearly. In this paper, taking an actual gymnasium of a long-span spatial steel-cable-membrane hybrid structure as the calculation model, the static and dynamic analyses of the hybrid structures are performed by employing the global analysis of the whole hybrid structure and the substructural analysis of the truss arch substructure, the cable-membrane substructure, etc. In addition, the comparison of stresses and displacements of structural members in the global and substructural analyses is made. The numerical results show that serious errors exist in the substructural analysis of the hybrid structure, and the global analysis is necessary for the hybrid structure under the excitation of static loads and seismic loads.展开更多
The giant magnetoresistive（MR） effect was investigated in a simple Fe/Si O2/p-Si-hybrid-structure-based device from two back-to-back Schottky diodes. The effect was revealed only under the non-equilibrium conditions...The giant magnetoresistive（MR） effect was investigated in a simple Fe/Si O2/p-Si-hybrid-structure-based device from two back-to-back Schottky diodes. The effect was revealed only under the non-equilibrium conditions caused by optical radiation. It is demonstrated that the magnetoresistance ratio attains 100 or more. The main peculiarity of the MR behavior is its strong dependence on the magnitude and the sign of the bias current across the device and, most surprisingly, upon polarity of the magnetic field. It is important that the magnetoresistive effect is implemented exclusively in the subsystem of minority charge carriers transferred to the non-equilibrium states. The development of magneto-sensitive devices of this type can give grounds for a novel direction of semiconductor spintronics.展开更多
The outstanding comprehensive mechanical properties of newly developed hybrid lattice structures make them useful in engineering applications for bearing multiple mechanical loads.Additive-manufacturing technologies m...The outstanding comprehensive mechanical properties of newly developed hybrid lattice structures make them useful in engineering applications for bearing multiple mechanical loads.Additive-manufacturing technologies make it possible to fabricate these highly spatially programmable structures and greatly enhance the freedom in their design.However,traditional analytical methods do not sufficiently reflect the actual vibration-damping mechanism of lattice structures and are limited by their high computational cost.In this study,a hybrid lattice structure consisting of various cells was designed based on quasi-static and vibration experiments.Subsequently,a novel parametric design method based on a data-driven approach was developed for hybrid lattices with engineered properties.The response surface method was adopted to define the sensitive optimization target.A prediction model for the lattice geometric parameters and vibration properties was established using a backpropagation neural network.Then,it was integrated into the genetic algorithm to create the optimal hybrid lattice with varying geometric features and the required wide-band vibration-damping characteristics.Validation experiments were conducted,demonstrating that the optimized hybrid lattice can achieve the target properties.In addition,the data-driven parametric design method can reduce computation time and be widely applied to complex structural designs when analytical and empirical solutions are unavailable.展开更多
Achieving exact printing fidelity in polymer-based bone regeneration scaffolds through additive manufacturing,particularly those of dispensing-type,remains a significant challenge.During fabrication,scaffolds often de...Achieving exact printing fidelity in polymer-based bone regeneration scaffolds through additive manufacturing,particularly those of dispensing-type,remains a significant challenge.During fabrication,scaffolds often deviate from the intended design geometry,which can negatively affect their performance.Additionally,achieving mechanical properties similar to natural bone in scaffolds remains challenging.Therefore,this study introduces the Hybrid Modified Cubic-Honeycomb Plate(hybrid MCHP)structure to improve printing fidelity and mechanical properties over previous bone regeneration scaffolds through innovative geometry design.This hybrid MCHP scaffold was inspired by cubic honeycomb and plate-lattice structures due to their excellent mechanical performance and well-optimized geometry,which ensure optimal printability.The effective elastic stiffness of the proposed structure and control group was predicted using a numerical Asymptotic Expansion Homogenization(AEH)model.Bone regeneration scaffolds were fabricated using Polycaprolactone(PCL)and a 3D printer with a Precision Extrusion Deposition(PED)system.Printing fidelity in manufactured scaffolds was then evaluated,resulting in a printing fidelity of 97.93±1.1%for the hybrid MCHP-structure scaffold(compared to 82.31±3.6%and 92.00±2.5%in the case of Kagome-structure and modified honeycomb(MHC)-structure scaffolds,which are the control groups).Mechanical testing of the hybrid MCHP-structure scaffold using a Universal Testing Machine(UTM)depicted similarity with 91.1%of the numerical estimated effective elastic stiffness(compared to 82.8%and 79.0%in the case of Kagome-structure and MHC-structure scaffolds,which serve as the control groups).The biological potential of the scaffolds was evaluated through in vitro studies using MC3T3-E1 pre-osteoblasts.The CCK-8 assay showed significantly enhanced cell viability and proliferation on the hybrid MCHP scaffold at all time points(days 1,7,and 14),consistently outperforming the Kagome and MHC scaffolds.Additionally,immunofluorescence staining analysis revealed abundant focal adhesions and uniform nuclear distribution,highlighting the superior cytocompatibility and effective support for cellular activity of the hybrid MCHP scaffold.展开更多
The effect of thermal degradation on the welded hybrid joints of metal and polymer composites is insufficient,which seriously inhibits the engineering applications of the joints.In this study,robust hybrid joints of m...The effect of thermal degradation on the welded hybrid joints of metal and polymer composites is insufficient,which seriously inhibits the engineering applications of the joints.In this study,robust hybrid joints of metal and polymer composites were fabricated by the combination of friction lap welding(FLW)and laser surface treatment for investigating the effect of accelerated aging on the joint properties.Results showed that the FLW hybrid joints without laser surface treatment exhibited 91%reduction in the tensile shear force(TSF)after 7 days of accelerated aging tests.In contrast,the FLW hybrid joints with suitable laser surface treatment exhibited only 26%reduction in TSF even after 35 days of accelerated aging tests.Fractures of the tensile specimens occurred across the composite plates rather than along the joint interface.The enhanced reliability of the hybrid joints was mainly attributed to(1)the formation of micro-mechanical interlocking between the polymer composites and aluminum alloy plate,and(2)the modification of the stress distribution along the joint interface.展开更多
Sub-wavelength nanostructure lattices provide versatile platforms for light control and the basis for various novel phenomena and applications in physics, material science, chemistry, biology,and energy. The thriving ...Sub-wavelength nanostructure lattices provide versatile platforms for light control and the basis for various novel phenomena and applications in physics, material science, chemistry, biology,and energy. The thriving study of nanostructure lattices is building on the remarkable progress of nanofabrication techniques, especially for the possibility of fabricating larger-area patterns while achieving higher-quality lattices, complex shapes, and hybrid materials units. In this review, we present a comprehensive review of techniques for large-area fabrication of optical nanostructure arrays, encompassing direct writing, self-assembly, controllable deposition, and nanoimprint/print methods. Furthermore, a particular focus is made on the recent improvement of unit accuracy and diversity, leading to integrated and multifunctional structures for devices and applications.展开更多
We present a novel, low-cost approach to fabricate flexible piezoelectric nano- generators （NGs） consisting of ZnO nanowires （NWs） on carbon fibers and foldable Au-coated ZnO NWs on paper. By using such designed s...We present a novel, low-cost approach to fabricate flexible piezoelectric nano- generators （NGs） consisting of ZnO nanowires （NWs） on carbon fibers and foldable Au-coated ZnO NWs on paper. By using such designed structure of the NGs, the radial ZnO NWs on a cylindrical fiber can be utilized fully and the electrical output of the NG is improved. The electrical output behavior of the NGs can be optionally controlled by increasing the fiber number, adjusting the strain rate and connection modes. For the single-fiber based NGs, the output voltage is 17 mV and the current density is about 0.09 μA·cm^-2, and the electrical output is enhanced greatly compared to that of previous similar micro-fiber based NGs. Compared with the single-fiber based NGs, the output current of the multi-fiber based NGs made of 200 carbon fibers increased 100-fold. An output voltage of 18 mV and current of 35 nA are generated from the multi-fiber based NGs. The electrical energy generated by the NGs is enough to power a practical device. The developed novel NGs can be used for smart textile structures, wearable and self-powered nanodevices.展开更多
In this paper,a brief review of the history of topological insulators is given.After that,electronic transport experiments in topological insulator-superconductor hybrid structures,including experimental methods,physi...In this paper,a brief review of the history of topological insulators is given.After that,electronic transport experiments in topological insulator-superconductor hybrid structures,including experimental methods,physical properties and seemingly contradictory observations are discussed.Additionally,some new topological insulator hybrid structures are proposed.展开更多
A hybrid catalyst structure can provide abundant active sites and tailored electronic properties,but the major challenge lies in achieving delicate control over its composition and architecture to improve the catalyti...A hybrid catalyst structure can provide abundant active sites and tailored electronic properties,but the major challenge lies in achieving delicate control over its composition and architecture to improve the catalytic activity toward different electrochemical reactions simultaneously.Herein,we present the rational design of a magic hybrid structure with low Pt loading(5.90 wt%),composed of CoPt_(3)and CoPt nanoparticles supported on N-doped carbon(CoPt_(3)/CoPt⊂PLNC).Importantly,it shows superior multifunctional catalytic activity in alkaline conditions,requiring a low overpotential of 341 and 20 mV to achieve 10 mA cm^(−2)for the hydrazine oxidation reaction(HzOR)/hydrogen evolution reaction(HER),respectively,and it delivers a half-wave potential of 0.847 V for the oxygen reduction reaction(ORR).Theoretical calculations reveal that the metal-carbon hybrid modulates kinetic behavior and induces electron redistribution,achieving the energetic requirements for multiple electrocatalysis.We demonstrate sustainable H_(2)production utilizing solely the CoPt_(3)/CoPt⊂PLNC catalyst,without external electric power input,suggesting its inspiring practical utility.展开更多
In this article,P-NiS_(2)/Ni_(x)P electrocatalysts were synthesized by dealloying the Ni-Al precursor followed by phosphosulfide treatment.We found that the hybrid structure of P-NiS_(2)/Ni_(x)P provides rich active s...In this article,P-NiS_(2)/Ni_(x)P electrocatalysts were synthesized by dealloying the Ni-Al precursor followed by phosphosulfide treatment.We found that the hybrid structure of P-NiS_(2)/Ni_(x)P provides rich active sites for the surface hydrogen evolution reaction (HER),and the doping of P enhances the electronic conductivity of electrodes.In particular,the obtained electrode shows a low overpotential of 196 mV at 10 mA cm^(-2)and a small Tafel slope of only 110 mV dec^(-1)in the HER.Meanwhile,longterm constant current electrolysis test experiments indicate that P-NiS_(2)/Ni_(x)P has good service stability.This research will help to open a new window on the design and fabrication of HER electrocatalysts.展开更多
In the present study, pool boiling heat transfer performance and bubble behaviors of hybrid structures with metal foam and square column are investigated by lattice Boltzmann method. By using the vapor-liquid phase ch...In the present study, pool boiling heat transfer performance and bubble behaviors of hybrid structures with metal foam and square column are investigated by lattice Boltzmann method. By using the vapor-liquid phase change model of Gong-Cheng and Peng-Robinson equation of state, the effects of structural parameters, including metal foam thickness, porosity, column height and ratio of column width(W) to gap spacing(D) are investigated in details. The results show that hybrid structure performs better than pure columnar structure in pool boiling heat transfer. The hybrid structure accelerates bubble growth by fluid disturbance while metal skeletons prevent the bubble escaping. The optimum ratio of column width to gap spacing decreases with the increase of heat flux and HTC(heat transfer coefficient) can achieve an increase up to 25% when W/D change from 5/3 to 1/3. The increase of column height enhances heat transfer by expanding surface area and providing space for bubble motion. The metal foam thickness and porosity have a little influence on pool boiling heat transfer performance, but they have an important effect on bubble motion in the regime.展开更多
A novel into-plane rotating rnicromirror actuated by a hybrid electrostatic driving structure is presented. The hybrid driving structure is made up of a planar plate drive and a vertical comb drive. The device is fabr...A novel into-plane rotating rnicromirror actuated by a hybrid electrostatic driving structure is presented. The hybrid driving structure is made up of a planar plate drive and a vertical comb drive. The device is fabricated in SOI substrate by using a bulk-and-surface mixed silicon micromachining process. As demonstrated by experiment, the novel driving structure can actuate the mirror to achieve large-range continuous rotation as well as spontaneous 90°rotation induced by the pull-in effect. The continuous rotating range of the micromirror is increased to about 46° at an increased yielding voltage. The measured yielding voltages of the mirrors with torsional springs of 1 and 0.5μm in thickness are 390 - 410V and 140 - 160V, respectively. The optical insertion loss has also been measured to be --1.98dB when the mirror serves as an optical switch.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52101138,52201075)Natural Science Foundation of Hubei Province,China(Nos.2023AFB798,2022CFB614)+3 种基金Shenzhen Science and Technology Program,China(No.JCYJ20220530160813032)State Key Laboratory of Solidification Processing in NWPU,China(Nos.SKLSP202309,SKLSP202308)Guangdong Basic and Applied Basic Research Foundation,China(No.2022A1515011227)State Key Laboratory of Powder Metallurgy of Central South University,China(No.Sklpm-KF-05).
文摘Metallic glass matrix composites(BMGCs)with compositions of[(Zr_(0.5)Cu_(0.5))_(0.925)Al_(0.07)Sn_(0.005)]_(100-x)Ta_(x)(atomic fraction,%,x=3,5,7)were successfully prepared via dealloying in metallic melt.The reinforcing phase in these alloys has core-shell hybrid structure with Ta-rich particles as core and B2-CuZr as shell.In this method,the dealloyed Ta from Zr-Ta pre-alloys maintained in solid state and aggregated to form the fine Ta-rich phase in the final products.This effectively decreases the size of Ta-rich phase compared with that prepared via conventional arc-melting,where the Ta-rich phase was formed through dissolving and precipitation.Among the three compositions,[(Zr_(0.5)Cu_(0.5))_(0.925)Al_(0.07)Sn_(0.005)]_(95)Ta_(5) showed the highest plastic strain of 11.2%,much higher than that of the arc-melted counterparts(4.3%).Such improvement in mechanical properties was related with the refined core-shell hybrid reinforcing structure,which could hinder the rapid propagation of main shear band more efficiently and cause them to branch and proliferate at the interface.
基金This work is supported by MOST of China （No.2011CB921403）, the Chinese Academy of Science, and the National Natural Science Foundation of China （No.10874165, No.90921013, No.11074231, and No. 11004179）.
文摘Ultraviolet （UV） photodetector constructed by ZnO material has attracted intense research and commercial interest. However, its photoresistivity and photoresonse are still unsatisfied. Herein, we report a novel method to assemble ZnO nanoparticles （NPs） onto the reduced graphite oxide （RGO） sheet by simple hydrothermal process without any surfactant. It is found that the high-quality crystallized ZnO NPs with the average diameter of 5 nm are well dispersed on the RGO surface, and the density of ZnO NPs can be readily controlled by the concentration of the precursor. The photodetector fabricated with this ZnO NPs- RGO hybrid structure demonstrates an excellent photoresponse for the UV irradiation. The results make this hybrid especially suitable as a novel material for the design and fabrication of high performance UV photodector.
基金supported by National Key Research and Development Program(No.2017YFB1102800)Key Project of NSFC(Nos.51790171 and 51761145111)NSFC for Excellent Young Scholars(No.11722219)。
文摘By integrating topology optimization and lattice-based optimization,a novel multi-scale design method is proposed to create solid-lattice hybrid structures and thus to improve the mechanical performance as well as reduce the structural weight.To achieve this purpose,a two-step procedure is developed to design and optimize the innovative structures.Initially,the classical topology optimization is utilized to find the optimal material layout and primary load carrying paths.Afterwards,the solid-lattice hybrid structures are reconstructed using the finite element mesh based modeling method.And lattice-based optimization is performed to obtain the optimal crosssection area of the lattice structures.Finally,two typical aerospace structures are optimized to demonstrate the effectiveness of the proposed optimization framework.The numerical results are quite encouraging since the solid-lattice hybrid structures obtained by the presented approach show remarkably improved performance when compared with traditional designs.
基金Supported by the National Natural Science Foundation of China （No.20436040） and Xi＇an Municipal Project for Industrial Research （No. GG06015）.
文摘A new design method for a water-reusing network, with a hybrid structure, to reduce the complexity of the network and to minimize freshwater consumption, is proposed. The unique feature of the methodology proposed .in this article is to control the complexity of the water network by regulation of the control number in a water-reusing system. It combines the advantages of a conventional water-reusing network and a water-reusing net work with internal water mains. To illustrate the proposed method, a single contaminant system and a multiple contaminant system serve as examples of the problems.
基金National Natural Science Foundation of China Under Grant No. 50708071National Basic Research of China Under Grant No. 2007CB714202+1 种基金National Key Technology R&D Program Under Grant No. 2006BAJ13B01Shanghai Educational Development Foundation Under Grant No. 2007CG27
文摘Many single-tower reinforced concrete core wall-steel frame （RCC-SF） buildings have been built in China, but there are no buildings of different-height multi-tower hybrid system. A multi-tower RCC-SF tall building was thus studied because of its structural complexity and irregularity. First, a 1/15 scaled model structure was designed and tested on the shake table under minor, moderate, and major earthquake levels. Then, the dynamic responses of the model structure were interpreted to those of the prototype structure according to the similitude theory. Experimental results demonstrate that, despite the complexity of the structure, the lateral deformation bends as the ＂bending type＂ and the RC core walls contribute more than the steel frames to resist seismic loads. The maximum inter-story drift of the complex building under minor earthquakes is slightly beyond the elastic limitation specified in the Chinese code, and meets code requirements under major earthquakes. From the test results some suggestions are provided that could contribute favorable effect on the seismic behavior and the displacement of the building.
基金the National Natural Science Foundation of China(No.51578160)
文摘Frame-masonry horizontal hybrid structure is a new type of self-built residence in the rural areas of Fujian Province in recent years. A shaking table test for 1/2 scale model is carried out on the basis of one representative rural structure, and the dynamic characteristics and seismic responses of this experimental model are measured. As a supplement, the finite element model of the prototype structure is built by ANSYS software,and simulation and test results are contrasted and analyzed. The results show that according to this structure,the beam-column joint of the frame part has stress concentration and the destruction pattern of the masonry part is similar to brick-masonry structure. There are obvious differences in lateral stiffness of each floor and direction,and the mass center does not coincide with the stiffness center, which can lead to excessive torsion and story drift of this structure under earthquakes of a certain intensity. Because of poor construction quality, unfavorable structural measures and irrational structural system in present rural areas, there is a potential safety threat with this type of structures in highly seismic region. Some suggestions for strengthening and retrofitting frame-masonry horizontal hybrid structures are pointed out.
基金Supported by the National Basic Research Program of China under Grant No 2011CB610300the National Natural Science Foundation of China under Grant Nos 11102148 and 11321062the Fundamental Research Funds for Central Universities of China
文摘We report an extraordinary sound absorption enhancement in low and intermediate frequencies achieved by a thin multi-slit hybrid structure formed by incorporating micrometer scale micro-slits into a sub-millimeter scale meso-slit matrix. Theoretical and numerical results reveal that this exotic phenomenon is attributed to the noticeable velocity and temperature gradients induced at the junctures of the micro- and meso-slits, which cause significant loss of sound energy as a result of viscous and thermal effects. It is demonstrated that the proposed thin multi-slit hybrid structure with micro-scale configuration is capable of controling low frequency noise with large wavelength, which is attractive for applications where the size and weight of a sound absorber are restricted.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61271070,61274074,and 60771019)the Key Research Program of Application Foundation and Advanced Technology of Tianjin,China(Grant No.11JCZDJC15300)
文摘We report on the fabrication and performance of a room-temperature NO2 gas sensor based on a WO3 nanowires/porous silicon hybrid structure. The W18O49 nanowires are synthesized directly from a sputtered tungsten film on a porous silicon （PS） layer under heating in an argon atmosphere. After a carefully controlled annealing treatment, WO3 nanowires are obtained on the PS layer without losing the morphology. The morphology, phase structure, and crystallinity of the nanowires are investigated by using field emission scanning electron microscopy （FESEM）, X-ray diffractometer （XRD）, and high-resolution transmission electron microscopy （HRTEM）. Comparative gas sensing results indicate that the sensor based on the WO3 nanowires exhibits a much higher sensitivity than that based on the PS and pure WO3 nanowires in detecting NO2 gas at room temperature. The mechanism of the WO3 nanowires/PS hybrid structure in the NO2 sensing is explained in detail.
文摘With the increment of the complexity of structural systems and the span of spatial structures, the interactions between parts of the structures, especially between some flexible substructures, become too complex to be analyzed clearly. In this paper, taking an actual gymnasium of a long-span spatial steel-cable-membrane hybrid structure as the calculation model, the static and dynamic analyses of the hybrid structures are performed by employing the global analysis of the whole hybrid structure and the substructural analysis of the truss arch substructure, the cable-membrane substructure, etc. In addition, the comparison of stresses and displacements of structural members in the global and substructural analyses is made. The numerical results show that serious errors exist in the substructural analysis of the hybrid structure, and the global analysis is necessary for the hybrid structure under the excitation of static loads and seismic loads.
基金supported by the Presidium of the Russian Academy of Sciences (project No. 20.8)the Division of Physical Sciences of the Russian Academy of Sciences (project No. II.4.3)+2 种基金the Siberian Branch of the Russian Academy of Sciences (integration projects Nos. 43, 85 and 102)the RF Ministry for Education and Science (project No. 02.G25.31.0043)the Russian Foundation of Basic Research (projects Nos. 14-0200234, 14-02-31156)
文摘The giant magnetoresistive（MR） effect was investigated in a simple Fe/Si O2/p-Si-hybrid-structure-based device from two back-to-back Schottky diodes. The effect was revealed only under the non-equilibrium conditions caused by optical radiation. It is demonstrated that the magnetoresistance ratio attains 100 or more. The main peculiarity of the MR behavior is its strong dependence on the magnitude and the sign of the bias current across the device and, most surprisingly, upon polarity of the magnetic field. It is important that the magnetoresistive effect is implemented exclusively in the subsystem of minority charge carriers transferred to the non-equilibrium states. The development of magneto-sensitive devices of this type can give grounds for a novel direction of semiconductor spintronics.
基金supported by National Natural Science Foundation of China(Grant No.52375380)National Key R&D Program of China(Grant No.2022YFB3402200)the Key Project of National Natural Science Foundation of China(Grant No.12032018).
文摘The outstanding comprehensive mechanical properties of newly developed hybrid lattice structures make them useful in engineering applications for bearing multiple mechanical loads.Additive-manufacturing technologies make it possible to fabricate these highly spatially programmable structures and greatly enhance the freedom in their design.However,traditional analytical methods do not sufficiently reflect the actual vibration-damping mechanism of lattice structures and are limited by their high computational cost.In this study,a hybrid lattice structure consisting of various cells was designed based on quasi-static and vibration experiments.Subsequently,a novel parametric design method based on a data-driven approach was developed for hybrid lattices with engineered properties.The response surface method was adopted to define the sensitive optimization target.A prediction model for the lattice geometric parameters and vibration properties was established using a backpropagation neural network.Then,it was integrated into the genetic algorithm to create the optimal hybrid lattice with varying geometric features and the required wide-band vibration-damping characteristics.Validation experiments were conducted,demonstrating that the optimized hybrid lattice can achieve the target properties.In addition,the data-driven parametric design method can reduce computation time and be widely applied to complex structural designs when analytical and empirical solutions are unavailable.
基金supported by a National Research Foundation of Korea(NRF)grant funded by Korean government(Nos.NRF-2022R1A4A1028747 and RS-2024-00344151).
文摘Achieving exact printing fidelity in polymer-based bone regeneration scaffolds through additive manufacturing,particularly those of dispensing-type,remains a significant challenge.During fabrication,scaffolds often deviate from the intended design geometry,which can negatively affect their performance.Additionally,achieving mechanical properties similar to natural bone in scaffolds remains challenging.Therefore,this study introduces the Hybrid Modified Cubic-Honeycomb Plate(hybrid MCHP)structure to improve printing fidelity and mechanical properties over previous bone regeneration scaffolds through innovative geometry design.This hybrid MCHP scaffold was inspired by cubic honeycomb and plate-lattice structures due to their excellent mechanical performance and well-optimized geometry,which ensure optimal printability.The effective elastic stiffness of the proposed structure and control group was predicted using a numerical Asymptotic Expansion Homogenization(AEH)model.Bone regeneration scaffolds were fabricated using Polycaprolactone(PCL)and a 3D printer with a Precision Extrusion Deposition(PED)system.Printing fidelity in manufactured scaffolds was then evaluated,resulting in a printing fidelity of 97.93±1.1%for the hybrid MCHP-structure scaffold(compared to 82.31±3.6%and 92.00±2.5%in the case of Kagome-structure and modified honeycomb(MHC)-structure scaffolds,which are the control groups).Mechanical testing of the hybrid MCHP-structure scaffold using a Universal Testing Machine(UTM)depicted similarity with 91.1%of the numerical estimated effective elastic stiffness(compared to 82.8%and 79.0%in the case of Kagome-structure and MHC-structure scaffolds,which serve as the control groups).The biological potential of the scaffolds was evaluated through in vitro studies using MC3T3-E1 pre-osteoblasts.The CCK-8 assay showed significantly enhanced cell viability and proliferation on the hybrid MCHP scaffold at all time points(days 1,7,and 14),consistently outperforming the Kagome and MHC scaffolds.Additionally,immunofluorescence staining analysis revealed abundant focal adhesions and uniform nuclear distribution,highlighting the superior cytocompatibility and effective support for cellular activity of the hybrid MCHP scaffold.
基金supported by the National Natural Science Foundation of China(No.51975553)the Liaoning Natural Science Foundation of China(Nos.2021-MS-007 and 2021-YQ-01)the Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2021193).
文摘The effect of thermal degradation on the welded hybrid joints of metal and polymer composites is insufficient,which seriously inhibits the engineering applications of the joints.In this study,robust hybrid joints of metal and polymer composites were fabricated by the combination of friction lap welding(FLW)and laser surface treatment for investigating the effect of accelerated aging on the joint properties.Results showed that the FLW hybrid joints without laser surface treatment exhibited 91%reduction in the tensile shear force(TSF)after 7 days of accelerated aging tests.In contrast,the FLW hybrid joints with suitable laser surface treatment exhibited only 26%reduction in TSF even after 35 days of accelerated aging tests.Fractures of the tensile specimens occurred across the composite plates rather than along the joint interface.The enhanced reliability of the hybrid joints was mainly attributed to(1)the formation of micro-mechanical interlocking between the polymer composites and aluminum alloy plate,and(2)the modification of the stress distribution along the joint interface.
基金National Natural Science Foundation of China (No. 62275257)startup funding from the Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciencesthe support of the Russian Science Foundation (No. 22-13-00126)。
文摘Sub-wavelength nanostructure lattices provide versatile platforms for light control and the basis for various novel phenomena and applications in physics, material science, chemistry, biology,and energy. The thriving study of nanostructure lattices is building on the remarkable progress of nanofabrication techniques, especially for the possibility of fabricating larger-area patterns while achieving higher-quality lattices, complex shapes, and hybrid materials units. In this review, we present a comprehensive review of techniques for large-area fabrication of optical nanostructure arrays, encompassing direct writing, self-assembly, controllable deposition, and nanoimprint/print methods. Furthermore, a particular focus is made on the recent improvement of unit accuracy and diversity, leading to integrated and multifunctional structures for devices and applications.
基金AcknowledgementsThis work was supported by the National Major Research Program of China （No. 2013CB932602）,the Major Project of International Cooperation and Exchanges （No. 2012DFA50990）, the National Natural Science Foundation of China （NSFC） （Nos. 51172022, 51232001, and 51372020）, the Fundamental Research Funds for Central Universities, the Program for New Century Excellent Talents in University, Beijing Higher Education Young Elite Teacher Project, the Programme of Introducing Talents of Discipline to Universities, and Program for Changjiang Scholars and Innovative Research Teams in University.
文摘We present a novel, low-cost approach to fabricate flexible piezoelectric nano- generators （NGs） consisting of ZnO nanowires （NWs） on carbon fibers and foldable Au-coated ZnO NWs on paper. By using such designed structure of the NGs, the radial ZnO NWs on a cylindrical fiber can be utilized fully and the electrical output of the NG is improved. The electrical output behavior of the NGs can be optionally controlled by increasing the fiber number, adjusting the strain rate and connection modes. For the single-fiber based NGs, the output voltage is 17 mV and the current density is about 0.09 μA·cm^-2, and the electrical output is enhanced greatly compared to that of previous similar micro-fiber based NGs. Compared with the single-fiber based NGs, the output current of the multi-fiber based NGs made of 200 carbon fibers increased 100-fold. An output voltage of 18 mV and current of 35 nA are generated from the multi-fiber based NGs. The electrical energy generated by the NGs is enough to power a practical device. The developed novel NGs can be used for smart textile structures, wearable and self-powered nanodevices.
基金supported by the National Basic Research Program of China(Grant No.2012CB921300)the National Natural Science Foundation of China(Grant No.11174007)the Penn State MRSEC(Grant No. DMR-0820404)
文摘In this paper,a brief review of the history of topological insulators is given.After that,electronic transport experiments in topological insulator-superconductor hybrid structures,including experimental methods,physical properties and seemingly contradictory observations are discussed.Additionally,some new topological insulator hybrid structures are proposed.
基金G.Q.Zhang acknowledges the financial support from the National Natural Science Foundation of China(Grant No.52072359)the Recruitment Program of Global Experts and the Fundamental Research Funds for the Central Universities(WK2060000016)The numerical calculations in this paper have been done in the Supercomputing Center of University of Science and Technology of China and TianHe-2 at LvLiang Cloud Computing Center of China.W.T.W.acknowledges the Natural Science Foundation from science and technology department of Guizhou Province(Nos.QHPT[2017]5790-02).
文摘A hybrid catalyst structure can provide abundant active sites and tailored electronic properties,but the major challenge lies in achieving delicate control over its composition and architecture to improve the catalytic activity toward different electrochemical reactions simultaneously.Herein,we present the rational design of a magic hybrid structure with low Pt loading(5.90 wt%),composed of CoPt_(3)and CoPt nanoparticles supported on N-doped carbon(CoPt_(3)/CoPt⊂PLNC).Importantly,it shows superior multifunctional catalytic activity in alkaline conditions,requiring a low overpotential of 341 and 20 mV to achieve 10 mA cm^(−2)for the hydrazine oxidation reaction(HzOR)/hydrogen evolution reaction(HER),respectively,and it delivers a half-wave potential of 0.847 V for the oxygen reduction reaction(ORR).Theoretical calculations reveal that the metal-carbon hybrid modulates kinetic behavior and induces electron redistribution,achieving the energetic requirements for multiple electrocatalysis.We demonstrate sustainable H_(2)production utilizing solely the CoPt_(3)/CoPt⊂PLNC catalyst,without external electric power input,suggesting its inspiring practical utility.
基金supported by the National Natural Science Foundation of China (Grant No. 51661018)。
文摘In this article,P-NiS_(2)/Ni_(x)P electrocatalysts were synthesized by dealloying the Ni-Al precursor followed by phosphosulfide treatment.We found that the hybrid structure of P-NiS_(2)/Ni_(x)P provides rich active sites for the surface hydrogen evolution reaction (HER),and the doping of P enhances the electronic conductivity of electrodes.In particular,the obtained electrode shows a low overpotential of 196 mV at 10 mA cm^(-2)and a small Tafel slope of only 110 mV dec^(-1)in the HER.Meanwhile,longterm constant current electrolysis test experiments indicate that P-NiS_(2)/Ni_(x)P has good service stability.This research will help to open a new window on the design and fabrication of HER electrocatalysts.
基金supported by the National Natural Science Foundation of China(Grant No.52276075)。
文摘In the present study, pool boiling heat transfer performance and bubble behaviors of hybrid structures with metal foam and square column are investigated by lattice Boltzmann method. By using the vapor-liquid phase change model of Gong-Cheng and Peng-Robinson equation of state, the effects of structural parameters, including metal foam thickness, porosity, column height and ratio of column width(W) to gap spacing(D) are investigated in details. The results show that hybrid structure performs better than pure columnar structure in pool boiling heat transfer. The hybrid structure accelerates bubble growth by fluid disturbance while metal skeletons prevent the bubble escaping. The optimum ratio of column width to gap spacing decreases with the increase of heat flux and HTC(heat transfer coefficient) can achieve an increase up to 25% when W/D change from 5/3 to 1/3. The increase of column height enhances heat transfer by expanding surface area and providing space for bubble motion. The metal foam thickness and porosity have a little influence on pool boiling heat transfer performance, but they have an important effect on bubble motion in the regime.
文摘A novel into-plane rotating rnicromirror actuated by a hybrid electrostatic driving structure is presented. The hybrid driving structure is made up of a planar plate drive and a vertical comb drive. The device is fabricated in SOI substrate by using a bulk-and-surface mixed silicon micromachining process. As demonstrated by experiment, the novel driving structure can actuate the mirror to achieve large-range continuous rotation as well as spontaneous 90°rotation induced by the pull-in effect. The continuous rotating range of the micromirror is increased to about 46° at an increased yielding voltage. The measured yielding voltages of the mirrors with torsional springs of 1 and 0.5μm in thickness are 390 - 410V and 140 - 160V, respectively. The optical insertion loss has also been measured to be --1.98dB when the mirror serves as an optical switch.
