To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretre...To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretreatment was employed to construct a Ta_(2)O_(5)ceramic layer on the Ta12W alloy surface.Subsequently,a slurry spraying-vacuum sintering method was used to prepare a Si-Cr-Ti-Zr coating on the pretreated substrate.Comparative studies were conducted on the microstructure,phase composition,and isothermal oxidation resistance(at 1600℃)of the as-prepared coatings with and without the micro-arc oxidation ceramic layer.The results show that the Ta_(2)O_(5)layer prepared at 400 V is more continuous and has smaller pores than that prepared at 350 V.After microarc oxidation pretreatment,the Si-Cr-Ti-Zr coating on Ta12W alloy consists of three distinct layers:an upper layer dominated by Ti_(5)Si_(3),Ta_(5)Si_(3),and ZrSi;a middle layer dominated by TaSi_(2);a coating/substrate interfacial reaction layer dominated by Ta_(5)Si_(3).Both the Si-Cr-Ti-Zr coatings with and without the Ta_(2)O_(5)ceramic layer do not fail after isothermal oxidation at 1600℃for 5 h.Notably,the addition of the Ta2O5 ceramic layer reduces the high-temperature oxidation rate of the coating.展开更多
To efficiently remove radioactive nuclides from nuclear industry wastewater and minimize the generation of radioactive secondary waste,this study proposes the concept of a magnetically controlled microchannel adsorber...To efficiently remove radioactive nuclides from nuclear industry wastewater and minimize the generation of radioactive secondary waste,this study proposes the concept of a magnetically controlled microchannel adsorber based on magnetic adsorbents.A novel protocol for achieving high adsorption performance in microchannel adsorbers with periodically distributed particles is developed using the particle-resolved computational fluid dynamics (CFD) method,which addresses the limitations of traditional porous media flow models.To align simulation results more closely with practical scenarios,a typical high-efficiency magnetic adsorbent,magnetic sodium alginate/cobalt-based Prussian blue (M-SA/PB-Co),was synthesized.The M-SA/PB-Co microspheres exhibit a uniform size distribution (300–600 μm),and their Cs^(+) adsorption follows the pseudo-second-order kinetic model with a Langmuir saturated adsorption capacity of 124.84 mg·g^(-1).The performance parameters of M-SA/PB-Co,obtained from characterization and adsorption experiments,were integrated into CFD simulations.CFD results indicate that as the flow velocity increases,the flow field gradually transitions with vortices expanding in scale and streamline bifurcation points shifting rearward.The Cs^(+) concentration decreases progressively along the flow direction,with a more pronounced reduction in the vortex regions downstream of particles.The characteristic velocity and characteristic concentration of specific regions surrounding the particles were extracted based on boundary layer distribution.The amount of concentration reduction of Cs^(+) through particle is positively correlated with the characteristic concentration and negatively correlated with the characteristic velocity.The number of microspheres required in the microchannel adsorber was optimized using the response surface method.Compared with industrial fixed-bed adsorbers,microchannel adsorbers exhibit 8–10 times higher processing capacity,demonstrating significant industrial application potential.展开更多
Economical and sustainable wastewater treatment techniques are highly demanded to alleviate the issues of clearwater scarcity globally.In this work,the acetic acid/H_(2)O_(2) (AHP) was leveraged to enrich oxygenated f...Economical and sustainable wastewater treatment techniques are highly demanded to alleviate the issues of clearwater scarcity globally.In this work,the acetic acid/H_(2)O_(2) (AHP) was leveraged to enrich oxygenated functional groups on the biochar surface for efficient ciprofloxacin (CIP) adsorption and biochar regeneration (In situ degradation of CIP in the spent AHP solution).The AHP-modified biochar exhibited significantly enhanced CIP adsorption capacity,about 22 times that of the pristine biochar.The optimized modification condition (acetic acid/H_(2)O_(2):2.11,temperature:45 ℃,and time:12 h) was screened by the response surface method,reaching the highest CIP adsorption capacity of 86.26 mg·g^(−1).Characterization results revealed that the content of carboxyl —C=O—O was enhanced in AHP-modified biochar,which contributed to efficient CIP adsorption by the electrostatic interaction,hydrogen bonding,and hydrophobic interaction.The adsorption of modified biochar to CIP molecules was a spontaneous endothermic process,and in line with the pseudo-second-order model and the Langmuir isotherm model.Moreover,the biochar modification process enabled the spent AHP solution with a strong oxidizing agent of peracetic acid (PAA),which can be employed to degrade adsorbed CIP for biochar in-situ generation.This work tailored a closed-loop strategy for biochar oxidation,contaminant adsorption,and biochar regeneration,highlighting a viable route for sustainable wastewater treatment.展开更多
The limited high-temperature oxidation resistance of Mg alloys is a key factor restricting their development and application.The addition of some rare earth elements(REs),owing to their unique physical and chemical pr...The limited high-temperature oxidation resistance of Mg alloys is a key factor restricting their development and application.The addition of some rare earth elements(REs),owing to their unique physical and chemical properties,can significantly enhance the oxidation resistance of Mg alloys.Based on our previous study,we conclude that REs such as Gd,Y,and Ce enhance the oxidation resistance of Mg-RE alloys.This article comprehensively reviews recent research progress on high-temperature oxidation behavior and the potential mechanism in Mg-RE alloys.Based on the thermodynamic and kinetic analyses,the evolution of the complex oxide system formed during the high-temperature oxidation of Mg-RE alloys is first summarized.The diffusion behavior and concentration control mechanisms of REs during the oxidation process and how these mechanisms affect the sustained growth of the oxide film and antioxidant properties were elucidated.Moreover,the different structures of the oxide films were classified,and their properties were discussed.Finally,this paper introduces the applications of commonly used REs in Mg alloys and frontier research on their oxidation mechanisms.Based on the above review,we propose that future research perspectives can be explored in terms of expanding the experimental temperature range for oxidation tests,optimizing the chemical composition by adding trace REs to study their synergistic mechanism,revealing the underlying oxidation mechanism through advanced in situ microscopic characterization methods,and investigating the mechanical properties of oxide films using diverse approaches.展开更多
Flubendiamide is a commonly used pesticide with low water solubility and a high organic carbon sorption constant,causing it to adhere to soil particles and negatively impact soil ecosystems.First,chili plant stems,typ...Flubendiamide is a commonly used pesticide with low water solubility and a high organic carbon sorption constant,causing it to adhere to soil particles and negatively impact soil ecosystems.First,chili plant stems,typically discarded after the harvest season,represent an abundant local biomass resource with significant potential for utilization,and were converted into biochar through pyrolysis.Here,we describe the synthesis of biochar modified with iron and chitosan to increase the diversity of functions and surface functional groups of biochar.The resulting chitosan-modified magnetic biochar(CMBC)presents a full range of functional groups of chitosan and iron oxide as shown by Fourier-transform infrared spectroscopy.The correlation between flubendiamide concentration and the dose of biochar on adsorption was explored.The flubendiamide adsorption efficiency of CMBC(1%mass ratio of soil)reached 68.03%in 90 min.The highest adsorption capacity achieved was 0.95 mg·g^(−1).The flubendiamide adsorption mechanism by CMBC can be described with a pseudo-second-order kinetic model.The experiment data closely fit a Freundlich isotherm model(R^(2)=0.998),and the low residual sum of squares values demonstrate the high model applicability.In this study,we present a comprehensive overview of pesticides,alongside kinetic and isotherm model studies of flubendiamide adsorption by CMBC.We emphasize the potential of modified biochar to enhance environmental remediation applications.展开更多
In this study,chitosan(CS)was combined with microcrystalline cellulose(MCC)to fabricate composite hydrogel beads.These beads were further modified through blending and grafting with polyethyleneimine(PEI)to develop ch...In this study,chitosan(CS)was combined with microcrystalline cellulose(MCC)to fabricate composite hydrogel beads.These beads were further modified through blending and grafting with polyethyleneimine(PEI)to develop chitosan/microcrystalline cellulose@polyethyleneimine(CS/MCC@PEI)composite gel spheres for the efficient adsorption of diclofenac sodium(DS)from aqueous solutions.The adsorbent was characterized using scanning electron microscopy(SEM),X-ray diffraction(XRD),Fourier-transform infrared spectroscopy(FTIR),X-ray pho-toelectron spectroscopy(XPS),and thermogravimetric analysis(TGA).The CS/MCC@PEI composite exhibited a spherical morphology with a porous structure,abundant surface functional groups,and a high adsorption capac-ity of 274.84 mg/g for DS.Kinetic studies revealed that the adsorption process followed the pseudo-second-order model,dominated by physical adsorption,with both surface and internal diffusion influencing the adsorption rate.The Freundlich isotherm model best described the adsorption behavior,indicating multilayer adsorption on heterogeneous surfaces.Environmental adaptability tests demonstrated minimal interference from co-existing anions and humic acid,while regeneration experiments confirmed excellent reusability(>77%removal after five cycles).The adsorption mechanism involved electrostatic interactions and hydrogen bonding between the hydroxyl/amino groups of the composite and DS.These findings highlight the potential of CS/MCC@PEI as a cost-effective and sustainable adsorbent for DS removal from water.展开更多
The flotation separation of argentite from sphalerite using ammonium dibutyl dithiophosphate(ADD)was studied.Molecular simulation(MS)calculation shows that ADD is chemisorbed on argentite and sphalerite surface in the...The flotation separation of argentite from sphalerite using ammonium dibutyl dithiophosphate(ADD)was studied.Molecular simulation(MS)calculation shows that ADD is chemisorbed on argentite and sphalerite surface in the form of S—P bond.The ADD adsorption on argentite and sphalerite surface in Ag^(+)system was revealed by ICP,Zeta potential and XPS analyses.It is shown that the dissolved Ag^(+)from argentite surface can be absorbed on sphalerite surface in the form of silver hydroxide,and AgOH hydrophilic colloid prevents the adsorption of ADD on sphalerite surface.The ADD adsorption on argentite and sphalerite surface in the pulp containing silver and zinc ions was revealed by adsorption capacity and surface wettability analyses.It is shown that the combined Zn(OH)_(2) and AgOH hydrophilic colloid leads to greater ADD adsorption capacity on argentite surface and stronger surface hydrophobicity than sphalerite.Flotation tests demonstrate that ADD enables efficient separation of argentite from sphalerite in the pulp containing silver and zinc ions.展开更多
This study presents a thorough investigation into the use of single and twin-tailed cationic and anionic surfactant-modified chitosan(SMCS)hydrogel beads as effective adsorbents for the elimination of hazardous polycy...This study presents a thorough investigation into the use of single and twin-tailed cationic and anionic surfactant-modified chitosan(SMCS)hydrogel beads as effective adsorbents for the elimination of hazardous polycyclic aromatic hydrocarbons(PAHs)from aqueous solutions.The Chitosan(CS)hydrogel beads were modified with single/twin-tailed anionic surfactants,sodium dodecyl sulfate(SDS)and sodium bis(2-ethylhexyl)sulfosuccinate(AOT),and cationic surfactants,dodecyltrimethylammonium bromide(DTAB)and didodecyldimethylammonium bromide(DDAB),to enhance their adsorption capacity of PAHs.The CS and SMCS beads were evaluated for their structural,mechanical,and adsorption properties using a range of techniques,including infrared spectroscopy(IR),energy-dispersive X-ray spectroscopy(EDX),rheometry,and field emission scanning electron microscopy(FESEM).Adsorption experiments of naphthalene(Nap),acenaphthene(Ace),and phenanthrene(Phe)on SMCS beads demonstrate that they have significantly higher adsorption capacities than CS beads,due to increase in hydrophobic interactions.Adsorption capacity followed the trend,Phen>Ace>Nap for all the beads revealing that twin-tailed SMCS bead possess much higher adsorption capacities(Qmax)compared to single-tailed SMCS beads.For twin tailed surfactants,the maximum adsorption capacities for Nap,Ace and Phe varied as CS-AOT(CS-DDAB):430.0(323.8)611.60(538.18)633.39(536.99)mg/g respectively,outperforming other reported hydrogel beads.The study highlights the simplicity,eco-friendliness,and enhanced performance of surfactant modification for developing high-efficiency adsorbents,paving the way for cost-effective solutions in water re-mediation.展开更多
In order to address the evolving emission characteristics of oxygenated volatile organic compounds(OVOCs),it is essential to develop adsorbent materials specifically designed for the efficient adsorption of OVOCs with...In order to address the evolving emission characteristics of oxygenated volatile organic compounds(OVOCs),it is essential to develop adsorbent materials specifically designed for the efficient adsorption of OVOCs with large kinetic diameters.In this study,we used co-pyrolysis to prepare a series of graded porous carbon materials with well-developed micropores by adjusting the doping ratios of root nodules and pretreated cellulose.The material with root nodule to cellulose mass ratio of 1:1(TCC-RN-1)exhibited the highest saturated adsorption capacity for butyl acetate(834 mg/g).This can be attributed to enhanced pore size distribution from nodule doping,which facilitates the development of a micropore-graded structure.Additionally,the nodules acted as auxiliary activating agents that enhanced the KOH micropore regulation effect during the activation stage,resulting in the highest micropore volume(0.863 cm^(3)/g).The doping of root nodules facilitated the formation of additional defects on the surface of the porous carbon material,leading to a more disordered arrangement that improved pollutant adsorption.Furthermore,TCC-RN-1 demonstrated good thermal stability in an air atmosphere,main-taining a butyl acetate adsorption capacity exceeding 95%after five adsorption-desorption cycles.This indicates its favorable potential for industrial applications.展开更多
Aqueous zinc-ion batteries(AZIBs) are regarded as one of the most promising energy conversion and storage devices.Nevertheless,side reactions and dendrite growth on the zinc metal anode hinder their widespread applica...Aqueous zinc-ion batteries(AZIBs) are regarded as one of the most promising energy conversion and storage devices.Nevertheless,side reactions and dendrite growth on the zinc metal anode hinder their widespread application.In this study,hemin was employed as a multi-functional artificial interface for the first time to inhibit the disordered growth of zinc dendrites and mitigate side reactions.Theoretical calculations indicate that hemin is preferentially adsorbed onto the zinc anode,thus blocking the interaction between the active zinc anode and electrolyte.Compared with zinc foil,the Hemin@Zn anode demonstrates enhanced corrosion resistance,a decrease in hydrogen evolution,and more orderly deposition of zinc.As expected,the symmetric cell with Hemin@Zn anode can sustain up to 4000 h at 0.2 mA/cm^(2),0.2 mAh/cm^(2).Asymmetric Zn//Cu cells exhibit an average coulombic efficiency exceeding 99.72 % during 500 cycles.Moreover,the full cell Hemin@Zn//NH_(4)V_(4)O_(10) delivers a superior capacity up to 367 m Ah/g and the discharge capacity retention reaches 124 mAh/g after 1200 cycles even at a current density of 5 A/g.This work provides a simple and effective method for constructing a robust artificial interface to promote the application of long-life AZIBs.展开更多
TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing Ti...TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing TiB_(2)coatings have disadvantages such as high equipment costs,complicated processes,and highly toxic gas emissions.This paper proposes an environmentally friendly method,which requires inexpensive equipment and simple processing,for preparing TiB_(2)coating on molybdenum via electrophoretic deposition within Na3AlF6-based molten salts.The produced TiB_(2)layer had an approximate thickness of 60μm and exhibited high density,outstanding hardness(38.2 GPa)and robust adhesion strength(51 N).Additionally,high-temperature oxidation experiments revealed that,at900℃,the TiB_(2)coating provided effective protection to the molybdenum substrate against oxidation for 3 h.This result indicates that the TiB_(2)coating prepared on molybdenum using molten salt electrophoretic deposition possesses good high-temperature oxidation resistance.展开更多
The severe shuttle effect and sluggish reaction kinetics in room-temperature sodium-sulfur(RT Na-S)batteries have been major bottlenecks hindering their practical application.To overcome these challenges,a straightfor...The severe shuttle effect and sluggish reaction kinetics in room-temperature sodium-sulfur(RT Na-S)batteries have been major bottlenecks hindering their practical application.To overcome these challenges,a straightforward reduction approach was employed to design three bimetallic alloy nanoparticles(FeNi,FeCo,and NiCo)supported on multistage porous carbon substrates.Experimental and theoretical calculations reveal that the charge transfer within the alloy catalyst influences the position of its d-band center and its degree of hybridization with sodium polysulfides(NaPSs).An increased charge transfer leads to a shift of the alloy’s d-band center closer to the Fermi energy level,thereby enhancing its adsorption and catalytic capabilities.Among the three alloy compositions,the FeNi alloy exhibits the highest charge transfer.Consequently,the FeNi alloy demonstrates the superior electrochemical performance,achieving a high reversible specific capacity of 848.2 mA h g^(−1),with an average capacity degradation rate of only 0.037%per cycle over 1000 cycles at 1.2 C.The S/FeNi/NC cathode exhibits a low electrolyte-to-sulfur(E/S)ratio of 6.6µL mg^(−1),while maintaining a high reversible specific capacity of 568.1 mA h g^(−1).This offers valuable insights for the application of alloy catalysts in the S/FeNi/NC cathode of RT Na-S batteries.展开更多
In this study,the design,analysis,manufacturing,and testing of a 3D-printed conformal microstrip array antenna for high-temperature environments is presented.3D printing technology is used to fabricate a curved cerami...In this study,the design,analysis,manufacturing,and testing of a 3D-printed conformal microstrip array antenna for high-temperature environments is presented.3D printing technology is used to fabricate a curved ceramic substrate,and laser sintering and microdroplet spraying processes are used to add the conductive metal on the curved substrate.The problems of gain loss,bandwidth reduction,and frequency shift caused by high temperatures are addressed by using a proper antenna design,with parasitic patches,slots,and metal resonant cavities.The antenna prototype is characterized by the curved substrates and the conductive metals for the power dividers,the patch,and the ground plane;its performance is examined up to a temperature of 600℃in a muffle furnace and compared with the results from the numerical analysis.The results show that the antenna can effectively function at 600℃and even higher temperatures.展开更多
Porous carbon microspheres are widely regarded as a superior CO_(2) adsorbent due to their exceptional efficiency and affordability.However,better adsorption performance is very attractive for porous carbon microspher...Porous carbon microspheres are widely regarded as a superior CO_(2) adsorbent due to their exceptional efficiency and affordability.However,better adsorption performance is very attractive for porous carbon microspheres.And modification of the pore structure is one of the effective strategies.In this study,multi-cavity mesoporous carbon microspheres were successfully synthesized by the synergistic method of soft and hard templates,during which a phenolic resin with superior thermal stability was employed as the carbon precursor and a mixture of silica sol and F108 as the mesoporous template.Carbon microspheres with multi-cavity mesoporous structures were prepared,and all the samples showed highly even mesopores,with diameters around 12 nm.The diameter of these microspheres decreased from 396.8 nm to about 182.5 nm with the increase of silica sol.After CO_(2) activation,these novel carbon microspheres(APCF0.5-S1.75)demonstrated high specific surface area(983.3 m^(2)/g)and remarkable CO_(2) uptake of 4.93 mmol/g at 0℃ and1 bar.This could be attributed to the unique multi-cavity structure,which offers uniform mesoporous pore channels,minimal CO_(2) transport of and a greater number of active sites for CO_(2) adsorption.展开更多
Metal hydrides with high hydrogen density provide promising hydrogen storage paths for hydrogen transportation.However,the requirement of highly pure H_(2)for re-hydrogenation limits its wide application.Here,amorphou...Metal hydrides with high hydrogen density provide promising hydrogen storage paths for hydrogen transportation.However,the requirement of highly pure H_(2)for re-hydrogenation limits its wide application.Here,amorphous Al_(2)O_(3)shells(10 nm)were deposited on the surface of highly active hydrogen storage material particles(MgH_(2)-ZrTi)by atomic layer deposition to obtain MgH_(2)-ZrTi@Al_(2)O_(3),which have been demonstrated to be air stable with selective adsorption of H_(2)under a hydrogen atmosphere with different impurities(CH_(4),O_(2),N_(2),and CO_(2)).About 4.79 wt% H_(2)was adsorbed by MgH_(2)-ZrTi@10nmAl_(2)O_(3)at 75℃under 10%CH_(4)+90%H_(2)atmosphere within 3 h with no kinetic or density decay after 5 cycles(~100%capacity retention).Furthermore,about 4 wt%of H_(2)was absorbed by MgH_(2)-ZrTi@10nmAl_(2)O_(3)under 0.1%O_(2)+0.4%N_(2)+99.5%H_(2)and 0.1%CO_(2)+0.4%N_(2)+99.5%H_(2)atmospheres at 100℃within 0.5 h,respectively,demonstrating the selective hydrogen absorption of MgH_(2)-ZrTi@10nmAl_(2)O_(3)in both oxygen-containing and carbon dioxide-containing atmospheres hydrogen atmosphere.The absorption and desorption curves of MgH_(2)-ZrTi@10nmAl_(2)O_(3)with and without absorption in pure hydrogen and then in 21%O_(2)+79%N_(2)for 1 h were found to overlap,further confirming the successful shielding effect of Al_(2)O_(3)shells against O_(2)and N_(2).The MgH_(2)-ZrTi@10nmAl_(2)O_(3)has been demonstrated to be air stable and have excellent selective hydrogen absorption performance under the atmosphere with CH_(4),O_(2),N_(2),and CO_(2).展开更多
Lithium-sulfur batteries(LSBs)can work at high temperatures,but they suffer from poor cycle life stability due to the“shuttle effect”of polysulfides.In this study,pollen-derived porous carbon/cuprous phosphide(PC/Cu...Lithium-sulfur batteries(LSBs)can work at high temperatures,but they suffer from poor cycle life stability due to the“shuttle effect”of polysulfides.In this study,pollen-derived porous carbon/cuprous phosphide(PC/Cu_(3)P)hybrids were rationally synthesized using a one-step carbonization method using pollen as the source material,acting as the sulfur host for LSBs.In the hybrid,polar Cu_(3)P can markedly inhibit the“shuttle effect”by regulating the adsorption ability toward polysulfides,as confirmed by theoretical calculations and experimental tests.As an example,the camellia pollen porous carbon(CPC)/Cu_(3)P/S electrode shows a high capacity of 1205.6 mAh g^(−1) at 0.1 C,an ultralow capacity decay rate of 0.038%per cycle after 1000 cycles at 1 C,and a rather high initial Coulombic efficiency of 98.5%.The CPC/Cu_(3)P LSBs can work well at high temperatures,having a high capacity of 545.9 mAh g^(−1) at 1 C even at 150℃.The strategy of the PC/Cu_(3)P hybrid proposed in this study is expected to be an ideal cathode for ultrastable high-temperature LSBs.We believe that this strategy is universal and worthy of in-depth development for the next generation energy storage devices.展开更多
Combustion-generated hydrogen chloride （HCl） is considered to be a very hazardous acid gaseous pollutant. This paper presents a laboratory study on the dry adsorption of HCl. The experiments were conducted in a dual...Combustion-generated hydrogen chloride （HCl） is considered to be a very hazardous acid gaseous pollutant. This paper presents a laboratory study on the dry adsorption of HCl. The experiments were conducted in a dual-layer granular bed filter, at gas temperatures of 500℃-700℃ and n（Ca）/n（Cl）molar ratios of 1.0-5.0 using the silver nitrate titration method by dry adsorbent powders Ca（OH）2. Mainly, the adsorption efficiency of HCI and utilization efficiency of Calcium were studied, by varying relevant factors including n（Ca）/n（Cl）, tempera- ture, feeding method, water vapor and CO2. With a relatively higher HCl concentration of 1000ppm, the experimental results revealed that 600℃ may be the optimum temperature for HCl adsorption when optimum n （Ca）/n（Cl） was 2.5 in our tests. The results also demonstrated that the feeding at a constant pressure was more effective, and the HCl adsorption efficiency could rapidly reach over 90% with n（Ca）/n（Cl） = 2.5 at 600℃. Furthermore, the HCl adsorption efficiency was found to be slightly promoted by water vapor, while could be impeded by CO2, and the utilization efficiency of calcium could be up to 74.4% without CO2, while was only 36.8% with CO2 when n（Ca）/n（Cl） was 2.5 at 600℃.展开更多
Since the application in fuel cell,the electrochemical adsorption of hydroxyl has received considerable attention in recent years.While most research mainly focus on the room temperature,in this paper,the electrochemi...Since the application in fuel cell,the electrochemical adsorption of hydroxyl has received considerable attention in recent years.While most research mainly focus on the room temperature,in this paper,the electrochemical adsorption of hydroxyl in alkaline solution at high temperature was investigated.An unusual oxidation peak was observed at-0.27 V,suggesting new behavior of hydroxyl adsorption occurred.As is known two kinds of cation hydrated clusters exist in alkaline solution,(H_(2)O)_(x-1)M^(+)-H_(2)O-O_(ad)H and(H_(2)O)_xM^(+)-O_(ad)H.For K^(+)and Cs^(+),the cluster shows unstable structure due to the weak interaction between hydrated cation and OH^(-)especially at high temperature.However,For Li^(+),Na^(+)the cluster structure would be stable,as the interaction force between the hydrated cation and OH^(-)is so strong.It was revealed that the unusual oxidation peak has some relationship with the(H_(2)O)_(x-1)M^(+)-H_(2)O-O_(ad)H cluster(K^(+)and Cs^(+))absorbed at Pt electrode surface.When the temperature was raised,(H_(2)O)_(x-1)M^(+)-H_(2)O-and-O_(ad)H was disconnected,then the O_(ad)H absorbed at Pt surface got oxidated.Based on the SEM observation,it was showed the unusual electrochemical oxidation reaction would generate platinum oxides,blocking the reactive sites at Pt electrode surface,thus reducing the electrochemical reactivity of Pt electrode.Accordingly,parameters of alkaline concentration and temperature were systematically studied,it was found that increase temperature or alkaline concentration was in favor of the unusual oxidation reaction.This study provides more understanding of hydroxyl adsorption behavior at Pt electrode surface for the high temperature water solution environment.展开更多
This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standar...This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.展开更多
Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,a...Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.展开更多
基金National Natural Science Foundation of China(52071274)Key Research and Development Projects of Shaanxi Province(2023-YBGY-442)Science and Technology Nova Project-Innovative Talent Promotion Program of Shaanxi Province(2020KJXX-062)。
文摘To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretreatment was employed to construct a Ta_(2)O_(5)ceramic layer on the Ta12W alloy surface.Subsequently,a slurry spraying-vacuum sintering method was used to prepare a Si-Cr-Ti-Zr coating on the pretreated substrate.Comparative studies were conducted on the microstructure,phase composition,and isothermal oxidation resistance(at 1600℃)of the as-prepared coatings with and without the micro-arc oxidation ceramic layer.The results show that the Ta_(2)O_(5)layer prepared at 400 V is more continuous and has smaller pores than that prepared at 350 V.After microarc oxidation pretreatment,the Si-Cr-Ti-Zr coating on Ta12W alloy consists of three distinct layers:an upper layer dominated by Ti_(5)Si_(3),Ta_(5)Si_(3),and ZrSi;a middle layer dominated by TaSi_(2);a coating/substrate interfacial reaction layer dominated by Ta_(5)Si_(3).Both the Si-Cr-Ti-Zr coatings with and without the Ta_(2)O_(5)ceramic layer do not fail after isothermal oxidation at 1600℃for 5 h.Notably,the addition of the Ta2O5 ceramic layer reduces the high-temperature oxidation rate of the coating.
基金Dalian distinguished young scholars program(2022RJ17)the Dalian excellent young talents program(2023RY037)provided funding for this study.
文摘To efficiently remove radioactive nuclides from nuclear industry wastewater and minimize the generation of radioactive secondary waste,this study proposes the concept of a magnetically controlled microchannel adsorber based on magnetic adsorbents.A novel protocol for achieving high adsorption performance in microchannel adsorbers with periodically distributed particles is developed using the particle-resolved computational fluid dynamics (CFD) method,which addresses the limitations of traditional porous media flow models.To align simulation results more closely with practical scenarios,a typical high-efficiency magnetic adsorbent,magnetic sodium alginate/cobalt-based Prussian blue (M-SA/PB-Co),was synthesized.The M-SA/PB-Co microspheres exhibit a uniform size distribution (300–600 μm),and their Cs^(+) adsorption follows the pseudo-second-order kinetic model with a Langmuir saturated adsorption capacity of 124.84 mg·g^(-1).The performance parameters of M-SA/PB-Co,obtained from characterization and adsorption experiments,were integrated into CFD simulations.CFD results indicate that as the flow velocity increases,the flow field gradually transitions with vortices expanding in scale and streamline bifurcation points shifting rearward.The Cs^(+) concentration decreases progressively along the flow direction,with a more pronounced reduction in the vortex regions downstream of particles.The characteristic velocity and characteristic concentration of specific regions surrounding the particles were extracted based on boundary layer distribution.The amount of concentration reduction of Cs^(+) through particle is positively correlated with the characteristic concentration and negatively correlated with the characteristic velocity.The number of microspheres required in the microchannel adsorber was optimized using the response surface method.Compared with industrial fixed-bed adsorbers,microchannel adsorbers exhibit 8–10 times higher processing capacity,demonstrating significant industrial application potential.
基金supported by the National Natural Science Foundation of China(22478266 and 32472027)the National Key Research&Development Program of China(2022YFE0207100)the Department of Science and Technology of Sichuan Province(2024ZYD0080 and 2022YFN0027).
文摘Economical and sustainable wastewater treatment techniques are highly demanded to alleviate the issues of clearwater scarcity globally.In this work,the acetic acid/H_(2)O_(2) (AHP) was leveraged to enrich oxygenated functional groups on the biochar surface for efficient ciprofloxacin (CIP) adsorption and biochar regeneration (In situ degradation of CIP in the spent AHP solution).The AHP-modified biochar exhibited significantly enhanced CIP adsorption capacity,about 22 times that of the pristine biochar.The optimized modification condition (acetic acid/H_(2)O_(2):2.11,temperature:45 ℃,and time:12 h) was screened by the response surface method,reaching the highest CIP adsorption capacity of 86.26 mg·g^(−1).Characterization results revealed that the content of carboxyl —C=O—O was enhanced in AHP-modified biochar,which contributed to efficient CIP adsorption by the electrostatic interaction,hydrogen bonding,and hydrophobic interaction.The adsorption of modified biochar to CIP molecules was a spontaneous endothermic process,and in line with the pseudo-second-order model and the Langmuir isotherm model.Moreover,the biochar modification process enabled the spent AHP solution with a strong oxidizing agent of peracetic acid (PAA),which can be employed to degrade adsorbed CIP for biochar in-situ generation.This work tailored a closed-loop strategy for biochar oxidation,contaminant adsorption,and biochar regeneration,highlighting a viable route for sustainable wastewater treatment.
基金supported by the Key R&D Program of Shandong Province,China(No.2025CXGC 010412)the National Key Research and Development Program of China(No.2022YFB3709300)the National Natural Science Foundation of China(No.U21A2048).
文摘The limited high-temperature oxidation resistance of Mg alloys is a key factor restricting their development and application.The addition of some rare earth elements(REs),owing to their unique physical and chemical properties,can significantly enhance the oxidation resistance of Mg alloys.Based on our previous study,we conclude that REs such as Gd,Y,and Ce enhance the oxidation resistance of Mg-RE alloys.This article comprehensively reviews recent research progress on high-temperature oxidation behavior and the potential mechanism in Mg-RE alloys.Based on the thermodynamic and kinetic analyses,the evolution of the complex oxide system formed during the high-temperature oxidation of Mg-RE alloys is first summarized.The diffusion behavior and concentration control mechanisms of REs during the oxidation process and how these mechanisms affect the sustained growth of the oxide film and antioxidant properties were elucidated.Moreover,the different structures of the oxide films were classified,and their properties were discussed.Finally,this paper introduces the applications of commonly used REs in Mg alloys and frontier research on their oxidation mechanisms.Based on the above review,we propose that future research perspectives can be explored in terms of expanding the experimental temperature range for oxidation tests,optimizing the chemical composition by adding trace REs to study their synergistic mechanism,revealing the underlying oxidation mechanism through advanced in situ microscopic characterization methods,and investigating the mechanical properties of oxide films using diverse approaches.
基金supported by research funds of Jeonbuk National University in 2024 and partly supported by the National Research Foundation of Korea(NRF-2019R1A2C1006441)from the Ministry of Education.
文摘Flubendiamide is a commonly used pesticide with low water solubility and a high organic carbon sorption constant,causing it to adhere to soil particles and negatively impact soil ecosystems.First,chili plant stems,typically discarded after the harvest season,represent an abundant local biomass resource with significant potential for utilization,and were converted into biochar through pyrolysis.Here,we describe the synthesis of biochar modified with iron and chitosan to increase the diversity of functions and surface functional groups of biochar.The resulting chitosan-modified magnetic biochar(CMBC)presents a full range of functional groups of chitosan and iron oxide as shown by Fourier-transform infrared spectroscopy.The correlation between flubendiamide concentration and the dose of biochar on adsorption was explored.The flubendiamide adsorption efficiency of CMBC(1%mass ratio of soil)reached 68.03%in 90 min.The highest adsorption capacity achieved was 0.95 mg·g^(−1).The flubendiamide adsorption mechanism by CMBC can be described with a pseudo-second-order kinetic model.The experiment data closely fit a Freundlich isotherm model(R^(2)=0.998),and the low residual sum of squares values demonstrate the high model applicability.In this study,we present a comprehensive overview of pesticides,alongside kinetic and isotherm model studies of flubendiamide adsorption by CMBC.We emphasize the potential of modified biochar to enhance environmental remediation applications.
基金supported by the Open Project Funding of Key Laboratory of Intelligent Health Perception and Ecological Restoration of Rivers and Lakes,Ministry of Education,Hubei University of Technology(No.HGKFZ03).
文摘In this study,chitosan(CS)was combined with microcrystalline cellulose(MCC)to fabricate composite hydrogel beads.These beads were further modified through blending and grafting with polyethyleneimine(PEI)to develop chitosan/microcrystalline cellulose@polyethyleneimine(CS/MCC@PEI)composite gel spheres for the efficient adsorption of diclofenac sodium(DS)from aqueous solutions.The adsorbent was characterized using scanning electron microscopy(SEM),X-ray diffraction(XRD),Fourier-transform infrared spectroscopy(FTIR),X-ray pho-toelectron spectroscopy(XPS),and thermogravimetric analysis(TGA).The CS/MCC@PEI composite exhibited a spherical morphology with a porous structure,abundant surface functional groups,and a high adsorption capac-ity of 274.84 mg/g for DS.Kinetic studies revealed that the adsorption process followed the pseudo-second-order model,dominated by physical adsorption,with both surface and internal diffusion influencing the adsorption rate.The Freundlich isotherm model best described the adsorption behavior,indicating multilayer adsorption on heterogeneous surfaces.Environmental adaptability tests demonstrated minimal interference from co-existing anions and humic acid,while regeneration experiments confirmed excellent reusability(>77%removal after five cycles).The adsorption mechanism involved electrostatic interactions and hydrogen bonding between the hydroxyl/amino groups of the composite and DS.These findings highlight the potential of CS/MCC@PEI as a cost-effective and sustainable adsorbent for DS removal from water.
基金the support from the National Key Research and Development Program of China (No. 2022YFC2904504)the Science and Technology Research Project of Jiangxi Provincial Department of Education, China (No. GJJ2200864)the Gansu Provincial Key Research and Development Project, China (No. 22YF7GA073)。
文摘The flotation separation of argentite from sphalerite using ammonium dibutyl dithiophosphate(ADD)was studied.Molecular simulation(MS)calculation shows that ADD is chemisorbed on argentite and sphalerite surface in the form of S—P bond.The ADD adsorption on argentite and sphalerite surface in Ag^(+)system was revealed by ICP,Zeta potential and XPS analyses.It is shown that the dissolved Ag^(+)from argentite surface can be absorbed on sphalerite surface in the form of silver hydroxide,and AgOH hydrophilic colloid prevents the adsorption of ADD on sphalerite surface.The ADD adsorption on argentite and sphalerite surface in the pulp containing silver and zinc ions was revealed by adsorption capacity and surface wettability analyses.It is shown that the combined Zn(OH)_(2) and AgOH hydrophilic colloid leads to greater ADD adsorption capacity on argentite surface and stronger surface hydrophobicity than sphalerite.Flotation tests demonstrate that ADD enables efficient separation of argentite from sphalerite in the pulp containing silver and zinc ions.
基金the Department of Science and Technology(DST),Govt.of India for providing funds under the FIST program and PURSE grant vide No.SR/PURSE/2020/31 to the department of Chemistry,University of Kashmir.
文摘This study presents a thorough investigation into the use of single and twin-tailed cationic and anionic surfactant-modified chitosan(SMCS)hydrogel beads as effective adsorbents for the elimination of hazardous polycyclic aromatic hydrocarbons(PAHs)from aqueous solutions.The Chitosan(CS)hydrogel beads were modified with single/twin-tailed anionic surfactants,sodium dodecyl sulfate(SDS)and sodium bis(2-ethylhexyl)sulfosuccinate(AOT),and cationic surfactants,dodecyltrimethylammonium bromide(DTAB)and didodecyldimethylammonium bromide(DDAB),to enhance their adsorption capacity of PAHs.The CS and SMCS beads were evaluated for their structural,mechanical,and adsorption properties using a range of techniques,including infrared spectroscopy(IR),energy-dispersive X-ray spectroscopy(EDX),rheometry,and field emission scanning electron microscopy(FESEM).Adsorption experiments of naphthalene(Nap),acenaphthene(Ace),and phenanthrene(Phe)on SMCS beads demonstrate that they have significantly higher adsorption capacities than CS beads,due to increase in hydrophobic interactions.Adsorption capacity followed the trend,Phen>Ace>Nap for all the beads revealing that twin-tailed SMCS bead possess much higher adsorption capacities(Qmax)compared to single-tailed SMCS beads.For twin tailed surfactants,the maximum adsorption capacities for Nap,Ace and Phe varied as CS-AOT(CS-DDAB):430.0(323.8)611.60(538.18)633.39(536.99)mg/g respectively,outperforming other reported hydrogel beads.The study highlights the simplicity,eco-friendliness,and enhanced performance of surfactant modification for developing high-efficiency adsorbents,paving the way for cost-effective solutions in water re-mediation.
基金supported by the National Natural Science Foundation of China(No.52370112).
文摘In order to address the evolving emission characteristics of oxygenated volatile organic compounds(OVOCs),it is essential to develop adsorbent materials specifically designed for the efficient adsorption of OVOCs with large kinetic diameters.In this study,we used co-pyrolysis to prepare a series of graded porous carbon materials with well-developed micropores by adjusting the doping ratios of root nodules and pretreated cellulose.The material with root nodule to cellulose mass ratio of 1:1(TCC-RN-1)exhibited the highest saturated adsorption capacity for butyl acetate(834 mg/g).This can be attributed to enhanced pore size distribution from nodule doping,which facilitates the development of a micropore-graded structure.Additionally,the nodules acted as auxiliary activating agents that enhanced the KOH micropore regulation effect during the activation stage,resulting in the highest micropore volume(0.863 cm^(3)/g).The doping of root nodules facilitated the formation of additional defects on the surface of the porous carbon material,leading to a more disordered arrangement that improved pollutant adsorption.Furthermore,TCC-RN-1 demonstrated good thermal stability in an air atmosphere,main-taining a butyl acetate adsorption capacity exceeding 95%after five adsorption-desorption cycles.This indicates its favorable potential for industrial applications.
基金financially supported by the National Natural Science Foundation of China (No.52372188)Natural Science Foundation of Henan (Nos.242300421625,252300421333)+4 种基金CAS Henan Industrial Technology Innovation & Incubation Center (No.2024121)Key Scientific Research Project of Education Department of Henan Province (Nos.22A150042,23A150038,and 24A150019)2023 Introduction of studying abroad talent programthe China Postdoctoral Science Foundation (No.2019 M652546)Key Project of Science and Technology of Henan Province (No.252102240007)。
文摘Aqueous zinc-ion batteries(AZIBs) are regarded as one of the most promising energy conversion and storage devices.Nevertheless,side reactions and dendrite growth on the zinc metal anode hinder their widespread application.In this study,hemin was employed as a multi-functional artificial interface for the first time to inhibit the disordered growth of zinc dendrites and mitigate side reactions.Theoretical calculations indicate that hemin is preferentially adsorbed onto the zinc anode,thus blocking the interaction between the active zinc anode and electrolyte.Compared with zinc foil,the Hemin@Zn anode demonstrates enhanced corrosion resistance,a decrease in hydrogen evolution,and more orderly deposition of zinc.As expected,the symmetric cell with Hemin@Zn anode can sustain up to 4000 h at 0.2 mA/cm^(2),0.2 mAh/cm^(2).Asymmetric Zn//Cu cells exhibit an average coulombic efficiency exceeding 99.72 % during 500 cycles.Moreover,the full cell Hemin@Zn//NH_(4)V_(4)O_(10) delivers a superior capacity up to 367 m Ah/g and the discharge capacity retention reaches 124 mAh/g after 1200 cycles even at a current density of 5 A/g.This work provides a simple and effective method for constructing a robust artificial interface to promote the application of long-life AZIBs.
基金supported by the Original Exploratory Program of the National Natural Science Foundation of China(No.52450012)。
文摘TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing TiB_(2)coatings have disadvantages such as high equipment costs,complicated processes,and highly toxic gas emissions.This paper proposes an environmentally friendly method,which requires inexpensive equipment and simple processing,for preparing TiB_(2)coating on molybdenum via electrophoretic deposition within Na3AlF6-based molten salts.The produced TiB_(2)layer had an approximate thickness of 60μm and exhibited high density,outstanding hardness(38.2 GPa)and robust adhesion strength(51 N).Additionally,high-temperature oxidation experiments revealed that,at900℃,the TiB_(2)coating provided effective protection to the molybdenum substrate against oxidation for 3 h.This result indicates that the TiB_(2)coating prepared on molybdenum using molten salt electrophoretic deposition possesses good high-temperature oxidation resistance.
基金supported by Shaanxi Fundamental Science Research Project for Chemistry and Biology(23JHQ011)Natural Science Foundation of Shaanxi(2024JC-YBMS-115)Natural Science Basic Research Plan in Shaanxi Province of China(2025JC-YBMS-141)。
文摘The severe shuttle effect and sluggish reaction kinetics in room-temperature sodium-sulfur(RT Na-S)batteries have been major bottlenecks hindering their practical application.To overcome these challenges,a straightforward reduction approach was employed to design three bimetallic alloy nanoparticles(FeNi,FeCo,and NiCo)supported on multistage porous carbon substrates.Experimental and theoretical calculations reveal that the charge transfer within the alloy catalyst influences the position of its d-band center and its degree of hybridization with sodium polysulfides(NaPSs).An increased charge transfer leads to a shift of the alloy’s d-band center closer to the Fermi energy level,thereby enhancing its adsorption and catalytic capabilities.Among the three alloy compositions,the FeNi alloy exhibits the highest charge transfer.Consequently,the FeNi alloy demonstrates the superior electrochemical performance,achieving a high reversible specific capacity of 848.2 mA h g^(−1),with an average capacity degradation rate of only 0.037%per cycle over 1000 cycles at 1.2 C.The S/FeNi/NC cathode exhibits a low electrolyte-to-sulfur(E/S)ratio of 6.6µL mg^(−1),while maintaining a high reversible specific capacity of 568.1 mA h g^(−1).This offers valuable insights for the application of alloy catalysts in the S/FeNi/NC cathode of RT Na-S batteries.
基金National Natural Science Foundation of China(No.U2241205)the Natural Science Basic Research Program of Shaanxi(Nos.2022JC-33,2023-GHZD-35,and 2024JC-ZDXM-25)+1 种基金the Fundamental Research Funds for the Central Universitiesthe National 111 Project to provide fund for conducting experiments。
文摘In this study,the design,analysis,manufacturing,and testing of a 3D-printed conformal microstrip array antenna for high-temperature environments is presented.3D printing technology is used to fabricate a curved ceramic substrate,and laser sintering and microdroplet spraying processes are used to add the conductive metal on the curved substrate.The problems of gain loss,bandwidth reduction,and frequency shift caused by high temperatures are addressed by using a proper antenna design,with parasitic patches,slots,and metal resonant cavities.The antenna prototype is characterized by the curved substrates and the conductive metals for the power dividers,the patch,and the ground plane;its performance is examined up to a temperature of 600℃in a muffle furnace and compared with the results from the numerical analysis.The results show that the antenna can effectively function at 600℃and even higher temperatures.
基金supported by the National Key R&D Program of China(No.2021YFB3501102).
文摘Porous carbon microspheres are widely regarded as a superior CO_(2) adsorbent due to their exceptional efficiency and affordability.However,better adsorption performance is very attractive for porous carbon microspheres.And modification of the pore structure is one of the effective strategies.In this study,multi-cavity mesoporous carbon microspheres were successfully synthesized by the synergistic method of soft and hard templates,during which a phenolic resin with superior thermal stability was employed as the carbon precursor and a mixture of silica sol and F108 as the mesoporous template.Carbon microspheres with multi-cavity mesoporous structures were prepared,and all the samples showed highly even mesopores,with diameters around 12 nm.The diameter of these microspheres decreased from 396.8 nm to about 182.5 nm with the increase of silica sol.After CO_(2) activation,these novel carbon microspheres(APCF0.5-S1.75)demonstrated high specific surface area(983.3 m^(2)/g)and remarkable CO_(2) uptake of 4.93 mmol/g at 0℃ and1 bar.This could be attributed to the unique multi-cavity structure,which offers uniform mesoporous pore channels,minimal CO_(2) transport of and a greater number of active sites for CO_(2) adsorption.
基金supported by the National Natural Science Foundation of China(22175136)the State Key Laboratory of Electrical Insulation and Power Equipment(EIPE23127)the Fundamental Research Funds for the Central Universities(xtr052024009).
文摘Metal hydrides with high hydrogen density provide promising hydrogen storage paths for hydrogen transportation.However,the requirement of highly pure H_(2)for re-hydrogenation limits its wide application.Here,amorphous Al_(2)O_(3)shells(10 nm)were deposited on the surface of highly active hydrogen storage material particles(MgH_(2)-ZrTi)by atomic layer deposition to obtain MgH_(2)-ZrTi@Al_(2)O_(3),which have been demonstrated to be air stable with selective adsorption of H_(2)under a hydrogen atmosphere with different impurities(CH_(4),O_(2),N_(2),and CO_(2)).About 4.79 wt% H_(2)was adsorbed by MgH_(2)-ZrTi@10nmAl_(2)O_(3)at 75℃under 10%CH_(4)+90%H_(2)atmosphere within 3 h with no kinetic or density decay after 5 cycles(~100%capacity retention).Furthermore,about 4 wt%of H_(2)was absorbed by MgH_(2)-ZrTi@10nmAl_(2)O_(3)under 0.1%O_(2)+0.4%N_(2)+99.5%H_(2)and 0.1%CO_(2)+0.4%N_(2)+99.5%H_(2)atmospheres at 100℃within 0.5 h,respectively,demonstrating the selective hydrogen absorption of MgH_(2)-ZrTi@10nmAl_(2)O_(3)in both oxygen-containing and carbon dioxide-containing atmospheres hydrogen atmosphere.The absorption and desorption curves of MgH_(2)-ZrTi@10nmAl_(2)O_(3)with and without absorption in pure hydrogen and then in 21%O_(2)+79%N_(2)for 1 h were found to overlap,further confirming the successful shielding effect of Al_(2)O_(3)shells against O_(2)and N_(2).The MgH_(2)-ZrTi@10nmAl_(2)O_(3)has been demonstrated to be air stable and have excellent selective hydrogen absorption performance under the atmosphere with CH_(4),O_(2),N_(2),and CO_(2).
基金supported by the Innovation Platform of Energy Storage Engineering and New Material in Zhejiang University(No.K19-534202-002)the National Natural Science Foundation of China(No.21978261)the Zhejiang Provincial Key Research and Development Program of China(No.2021C01030).
文摘Lithium-sulfur batteries(LSBs)can work at high temperatures,but they suffer from poor cycle life stability due to the“shuttle effect”of polysulfides.In this study,pollen-derived porous carbon/cuprous phosphide(PC/Cu_(3)P)hybrids were rationally synthesized using a one-step carbonization method using pollen as the source material,acting as the sulfur host for LSBs.In the hybrid,polar Cu_(3)P can markedly inhibit the“shuttle effect”by regulating the adsorption ability toward polysulfides,as confirmed by theoretical calculations and experimental tests.As an example,the camellia pollen porous carbon(CPC)/Cu_(3)P/S electrode shows a high capacity of 1205.6 mAh g^(−1) at 0.1 C,an ultralow capacity decay rate of 0.038%per cycle after 1000 cycles at 1 C,and a rather high initial Coulombic efficiency of 98.5%.The CPC/Cu_(3)P LSBs can work well at high temperatures,having a high capacity of 545.9 mAh g^(−1) at 1 C even at 150℃.The strategy of the PC/Cu_(3)P hybrid proposed in this study is expected to be an ideal cathode for ultrastable high-temperature LSBs.We believe that this strategy is universal and worthy of in-depth development for the next generation energy storage devices.
文摘Combustion-generated hydrogen chloride （HCl） is considered to be a very hazardous acid gaseous pollutant. This paper presents a laboratory study on the dry adsorption of HCl. The experiments were conducted in a dual-layer granular bed filter, at gas temperatures of 500℃-700℃ and n（Ca）/n（Cl）molar ratios of 1.0-5.0 using the silver nitrate titration method by dry adsorbent powders Ca（OH）2. Mainly, the adsorption efficiency of HCI and utilization efficiency of Calcium were studied, by varying relevant factors including n（Ca）/n（Cl）, tempera- ture, feeding method, water vapor and CO2. With a relatively higher HCl concentration of 1000ppm, the experimental results revealed that 600℃ may be the optimum temperature for HCl adsorption when optimum n （Ca）/n（Cl） was 2.5 in our tests. The results also demonstrated that the feeding at a constant pressure was more effective, and the HCl adsorption efficiency could rapidly reach over 90% with n（Ca）/n（Cl） = 2.5 at 600℃. Furthermore, the HCl adsorption efficiency was found to be slightly promoted by water vapor, while could be impeded by CO2, and the utilization efficiency of calcium could be up to 74.4% without CO2, while was only 36.8% with CO2 when n（Ca）/n（Cl） was 2.5 at 600℃.
基金the National Key Research and Development Program of China(2020YFC1909703)S&T Program of Hebei Province(21284402Z)+1 种基金Fangchenggang Key Research and Development(AB20014008)Lvliang Key Research and Development Program(2020GXZDYF7)。
文摘Since the application in fuel cell,the electrochemical adsorption of hydroxyl has received considerable attention in recent years.While most research mainly focus on the room temperature,in this paper,the electrochemical adsorption of hydroxyl in alkaline solution at high temperature was investigated.An unusual oxidation peak was observed at-0.27 V,suggesting new behavior of hydroxyl adsorption occurred.As is known two kinds of cation hydrated clusters exist in alkaline solution,(H_(2)O)_(x-1)M^(+)-H_(2)O-O_(ad)H and(H_(2)O)_xM^(+)-O_(ad)H.For K^(+)and Cs^(+),the cluster shows unstable structure due to the weak interaction between hydrated cation and OH^(-)especially at high temperature.However,For Li^(+),Na^(+)the cluster structure would be stable,as the interaction force between the hydrated cation and OH^(-)is so strong.It was revealed that the unusual oxidation peak has some relationship with the(H_(2)O)_(x-1)M^(+)-H_(2)O-O_(ad)H cluster(K^(+)and Cs^(+))absorbed at Pt electrode surface.When the temperature was raised,(H_(2)O)_(x-1)M^(+)-H_(2)O-and-O_(ad)H was disconnected,then the O_(ad)H absorbed at Pt surface got oxidated.Based on the SEM observation,it was showed the unusual electrochemical oxidation reaction would generate platinum oxides,blocking the reactive sites at Pt electrode surface,thus reducing the electrochemical reactivity of Pt electrode.Accordingly,parameters of alkaline concentration and temperature were systematically studied,it was found that increase temperature or alkaline concentration was in favor of the unusual oxidation reaction.This study provides more understanding of hydroxyl adsorption behavior at Pt electrode surface for the high temperature water solution environment.
文摘This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.
基金National Natural Science Foundation of China(52071126)Natural Science Foundation of Tianjin City,China(22JCQNJC01240)+2 种基金Central Guidance on Local Science and Technology Development Fund of Hebei Province(226Z1009G)Special Funds for Science and Technology Innovation in Hebei(2022X19)Anhui Provincial Natural Science Foundation(2308085ME135)。
文摘Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.
