This work focuses on the influence of Al content on the precipitation of nanoprecipitates,growth of prior austenite grains(PAGs),and impact toughness in simulated coarse-grained heat-affected zones (CGHAZs) of two exp...This work focuses on the influence of Al content on the precipitation of nanoprecipitates,growth of prior austenite grains(PAGs),and impact toughness in simulated coarse-grained heat-affected zones (CGHAZs) of two experimental shipbuilding steels after being subjected to high-heat input welding at 400 kJ·cm^(-1).The base metals (BMs) of both steels contained three types of precipitates Type Ⅰ:cubic (Ti,Nb)(C,N),Type Ⅱ:precipitate with cubic (Ti,Nb)(C,N) core and Nb-rich cap,and Type Ⅲ:ellipsoidal Nb-rich precipitate.In the BM of 60Al and 160Al steels,the number densities of the precipitates were 11.37×10^(5) and 13.88×10^(5) mm^(-2),respectively The 60Al and 160Al steel contained 38.12% and 6.39% Type Ⅲ precipitates,respectively.The difference in the content of Type Ⅲ precipitates in the 60Al steel reduced the pinning effect at the elevated temperature of the CGHAZ,which facilitated the growth of PAGs The average PAG sizes in the CGHAZ of the 60Al and 160Al steels were 189.73 and 174.7μm,respectively.In the 60Al steel,the low lattice mismatch among Cu_(2)S,TiN,and γ-Al_(2)O_(3)facilitated the precipitation of Cu_(2)S and TiN onto γ-Al_(2)O_(3)during welding,which decreased the number density of independently precipitated (Ti,Nb)(C,N) particles but increased that of γ-Al_(2)O_(3)–Ti N–Cu_(2)S particles.Thus abnormally large PAGs formed in the CGHAZ of the 60Al steel,and they reached a maximum size of 1 mm.These PAGs greatly reduced the microstructural homogeneity and consequently decreased the impact toughness from 134 (0.016wt%Al) to 54 J (0.006wt%Al)at-40℃.展开更多
The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional the...The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.展开更多
The evolution of the microstructure and toughness of APL5L X80 pipeline steel after thermal welding simulation was investigated by X-ray diffraction,electron backscatter diffraction,and transmission electron microscop...The evolution of the microstructure and toughness of APL5L X80 pipeline steel after thermal welding simulation was investigated by X-ray diffraction,electron backscatter diffraction,and transmission electron microscopy.The results indicated that primary heat-affected zones can be divided into weld,coarse-grained,fine-grained,intercritical,and sub-critical zones.The microstructure of the weld zone is mainly composed of bainitic ferrite and a small amount of granular bainite;however,the original austenite grains are distributed in the columnar grains.The structure of the coarse-grained zone is similar to that of the weld zone,but the original austenite grains are equiaxed.In contrast,the microstructure in the fine-grained zone is dominated by fine granular bainite,and the effective grain size is only 8.15μm,thus providing the highest toughness in the entire heat-affected zone.The intercritical and subcritical zones were brittle valley regions,and the microstructure was dominated by granular bainite.However,the martensite-austenite(M/A)constituents are present in island chains along the grain boundaries,and the coarse size of the M/A constituents seriously reduces the toughness.The results of the crack propagation analyzes revealed that high-angle grain boundaries can significantly slow down crack growth and change the crack direction,thereby increasing the material toughness.The impact toughness of the low-temperature tempering zone was equivalent to that of the columnar grain zone,and the impact toughness was between those of the critical and fine-grained zones.展开更多
Improvement of fabrication efficiency and part performance was the main challenge for the large-scale powder bed fusion(PBF)process.In this study,a dynamic monitoring and feedback system of powder bed temperature fiel...Improvement of fabrication efficiency and part performance was the main challenge for the large-scale powder bed fusion(PBF)process.In this study,a dynamic monitoring and feedback system of powder bed temperature field using an infrared thermal imager has been established and integrated into a four-laser PBF equipment with a working area of 2000 mm×2000 mm.The heat-affected zone(HAZ)temperature field has been controlled by adjusting the scanning speed dynamically.Simultaneously,the relationship among spot size,HAZ temperature,and part performance has been established.The fluctuation of the HAZ temperature in four-laser scanning areas was decreased from 30.85℃to 17.41℃.Thus,the consistency of the sintering performance of the produced large component has been improved.Based on the controllable temperature field,a dynamically adjusting strategy for laser spot size was proposed,by which the fabrication efficiency was improved up to 65.38%.The current research results were of great significance to the further industrial applications of large-scale PBF equipment.展开更多
The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then gre...The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then grew in different directions through movement of grain boundaries into the ferrite phase. Subsequently, the adjacent austenite grains impinged against each other during the α→γtransformation. After the α→γ transformation, austenite grains coarsened via the coalescence of small grains and via boundary migration between grains. The growth process of austenite grains was a continuous process during heating, isothermal holding, and cooling in simulated thermal cycling. Abundant finely dispersed nanoscale TiN particles in a steel specimen containing 0.012wt% Ti effectively retarded the grain boundary migration, which resulted in refined austenite grains. When the Ti concentration in the steel was increased, the number of TiN particles de- creased and their size coarsened. The big particles were not effective in pinning the austenite grain boundary movement and resulted in coarse austenite grains.展开更多
The effects of Mg content, inclusion size, and austenite grain size on the intragranular acicular ferrite （IAF） nucleation in heat-affected zone of steel plate after high-heat-input welding of 400 kJ/cm were investi...The effects of Mg content, inclusion size, and austenite grain size on the intragranular acicular ferrite （IAF） nucleation in heat-affected zone of steel plate after high-heat-input welding of 400 kJ/cm were investigated by welding simulation and observation using a scanning electron microscope equipped with an energy dispersive spectrometer and an optical microscope. The IAFs are observed in steel with Mg addition, and the volume fraction of IAF is as high as 55.4% in the steel containing 0.0027 mass% Mg. The MgO-Al2O3-Ti2O3-MnS inclusions with size around 2 μm are effective nucleation sites for IAF, whereas Al2O3-MnS inclusions are impotent to nucleate the acicular ferrite. The prior-austenite grain （PAG） size distribution in low Mg steel is similar to that in steel without Mg addition. The austenite grain with size about 200 μm is favorable for the IAF formation. In the steel with high Mg content of 0.0099%, the growth of PAG is greatly inhibited, and PAG sizes are smaller than 100 μm. Therefore, the nucleation of IAF can hardly be observed.展开更多
In this work,the stress corrosion cracking(SCC)behavior of E690 steel base metal(BM)and different heat-affected zone(HAZ)microstructures,i.e.,coarse grain HAZ(CGHAZ),fine grain HAZ(FGHAZ),and intercritical HAZ(ICHAZ),...In this work,the stress corrosion cracking(SCC)behavior of E690 steel base metal(BM)and different heat-affected zone(HAZ)microstructures,i.e.,coarse grain HAZ(CGHAZ),fine grain HAZ(FGHAZ),and intercritical HAZ(ICHAZ),was investigated at different cathodic potentials in artificial seawater by slow strain rate tensile tests,scanning electron microscopy and electron back-scattered diffraction measurements.The results show that the HAZ microstructures and BM exhibit different SCC susceptibilities:FGHAZ<ICHAZ<BM<CGHAZ,which are controlled by anodic dissolution(AD)at the open circuit potential.With the cathodic potential equaling to-750 mV,the SCC susceptibility of the four microstructures increases because of the synergistic effect of AD and weak hydrogen embrittlement(HE).At-850 mV,AD is inhibited,and the SCC susceptibility of BM decreases,while the SCC susceptibility of the HAZ microstructures increases.At a potential below-850 mV,the SCC susceptibility of the four microstructures gradually increases because of the augment of HE,and the SCC susceptibility of the HAZ microstructures is higher than that of BM.The distinction reveals that the HAZ microstructures have the greater HE susceptibility than BM.展开更多
The combined influence of Mg and Ca treatment on the properties of heat-affected zone (HAZ) of low-carbon steel after high heat input welding was systematically studied. Experimental steels deoxidized with different e...The combined influence of Mg and Ca treatment on the properties of heat-affected zone (HAZ) of low-carbon steel after high heat input welding was systematically studied. Experimental steels deoxidized with different elements were prepared, i.e., C-Mn steel with Al, Ti-Ca steel with Ti and Ca, Ti-Mg-Ca steel with Ti, Mg and Ca. Results showed that the inclusions in C-Mn steel were mainly Al2O3 and MnS with low density and large size. However, the average size was refined to only ~0.34 μm in Ti-Mg-Ca steel and the amount increased remarkably. Microstructure of simulated HAZ for 200 kJ/cm changed from ferrite side plates or upper bainite to acicular ferrite after treatment with Ti, Mg and Ca. Ca addition decreased the strain field around inclusions and enhanced the ability of acicular ferrite nucleation. In situ observation of Ti-Mg-Ca steel showed that the movement of austenite grain boundaries was retarded and nucleation sites of acicular ferrite were greater than Ti-Ca steel because of Mg addition. Impact energy of HAZ at — 40℃ was increased from 7 to 232 J and showed excellent stability because of Ti-Mg-Ca treatment. High volume fraction of acicular ferrite acted as obstacles toward cleavage cracks.展开更多
The intercritical heat-affected zone（ICHAZ） of X80 pipeline steel was simulated by using the Gleeble-3500thermal/mechanical simulator according to the thermal cycle of in-service welding.The microstructures of ICHAZ...The intercritical heat-affected zone（ICHAZ） of X80 pipeline steel was simulated by using the Gleeble-3500thermal/mechanical simulator according to the thermal cycle of in-service welding.The microstructures of ICHAZ with different cooling rates were examined,and the hardness,the toughness and corresponding fractography were investigated.Results show that untransformed bainite and ferrite as well as retransformed fine bainite and martensite–austenite（M–A）constituents constitute the microstructure of ICHAZ.The two different morphologies of M–A constituents are stringer and block.Second phase particles which mainly composed of Ti,Nb,C,Fe and Cu coarsened in ICHAZ.Compared with normal welding condition,the toughness of ICHAZ is poor when the cooling time is short under in-service welding condition because of the large area fraction and size of M–A constituents that connect into chains and distribute at the grain boundaries.The Vickers hardness of ICHAZ that decreases with the increase in the cooling time is independent with the area fraction of M–A constituents.展开更多
The continuous cooling transformation curve of heat-affected zone （HAZ） of X70 pipeline steel was mea- sured by Gleeble-3500 thermal mechanical simulator, optical microscope （OM） and hardness analysis. The microst...The continuous cooling transformation curve of heat-affected zone （HAZ） of X70 pipeline steel was mea- sured by Gleeble-3500 thermal mechanical simulator, optical microscope （OM） and hardness analysis. The microstructure transformation rule at different cooling rates and solution behaviors of microalloy carbonitride during heating process of simulated specimens were investigated. When the cooling rate changes from 10 to 20 ℃.s-l, microstructures at HAZ are identified as granular bainite, lathy bainite, and quasi-polygonal ferrite. This micro- structure is featured with fine ferrite grains, martensite/ austenite islands dispersed, high-density dislocations, and fine carbonitride particles, resulting in improving the strength and toughness of HAZ. With the cooling rate increasing to above 40 ℃.s-1, the microstructure is pre- dominantly coarse lathy bainite with clear primary aus- tenite grain boundary. While the cooling rate decreases to below 1 ℃.s-1, a fairly small amount of pearlite can be observed at the boundaries. The strength and toughness of HAZ are deteriorated because of coarse grains among these microstructures. Most of microalloy carbonitrides in HAZ could be dissolved in the matrix during heating process. A few of TiN particles existing as residues in the matrix can prevent austenite grain from growing, and then improve the strength and toughness of HAZ.展开更多
The structure-property relationship in heat-affected zone (HAZ)of a low-carbon steel bearing V-N subjected to gasshielded arc welding was explored.The microstructural characteristics of base metal (BM),coarse-grained ...The structure-property relationship in heat-affected zone (HAZ)of a low-carbon steel bearing V-N subjected to gasshielded arc welding was explored.The microstructural characteristics of base metal (BM),coarse-grained HAZ (CGHAZ),fine-grained HAZ,and intercritical HAZ were significantly different.The effect of grain-refinement strengthening and transformation hardening on HAZ contributed to equivalent hardness of 260.8-278.5 HV in comparison with BM hardness of 272.0 HV.Moreover,excellent impact toughness at -20 ℃ was obtained because of high resistance to crack propagation by high-misorientation boundaries,leading to impact fracture consisting of dimples.In CGHAZ,free N was partly fixed by V(C,N)precipitates,such that the deterioration effect of N on toughness was considered to be nearly eliminated.In comparison with CGHAZ,weld metal contained higher fraction of acicular ferrite with fine plates,while the impact toughness was inferior because of the detrimental influence of coarse inclusions from the welding wire.The nanoscale V(C,N)precipitates in CGHAZ had weak effect on toughness because of small size.展开更多
The main aim of this study was to investigate liquation cracking in the heat-affected zone(HAZ)of the IN939 superalloy upon tungsten inert gas welding.A solid solution and age-hardenable filler metals were further stu...The main aim of this study was to investigate liquation cracking in the heat-affected zone(HAZ)of the IN939 superalloy upon tungsten inert gas welding.A solid solution and age-hardenable filler metals were further studied.On the pre-weld heat-treated samples,upon solving the secondaryγ′particles in the matrix,primaryγ′particles in the base metal grew to"ogdoadically diced cubes"of about 2μm in side lengths.The pre-weld heat treatment reduced the hardness of the base metal to about HV 310.Microstructural studies using optical and fieldemission scanning electron microscopy revealed that the IN939 alloy was susceptible to liquation cracking in the HAZ.The constitutional melting of the secondary,eutectic,and Zr-rich phases promoted the liquation cracking in the HAZ.The microstructure of the weld fusion zones showed the presence of fine spheroidalγ′particles with sizes of about 0.2μm after the post-weld heat treatment,which increased the hardness of the weld pools to about HV 350 and 380 for the Hastelloy X and IN718 filler metals,respectively.Application of a suitable solid solution filler metal could partially reduce the liquation cracking in the HAZ of IN939 alloy.展开更多
Continuous cooling transformation diagrams in synthetic weld heat-affected zone(SH-CCT diagrams)show the phase transition temperature and hardness at different cooling rates,which is an important basis for formulating...Continuous cooling transformation diagrams in synthetic weld heat-affected zone(SH-CCT diagrams)show the phase transition temperature and hardness at different cooling rates,which is an important basis for formulating the welding process or predicting the performance of welding heat-affected zone.However,the experimental determination of SH-CCT diagrams is a time-consuming and costly process,which does not conform to the development trend of new materials.In addition,the prediction of SHCCT diagrams using metallurgical models remains a challenge due to the complexity of alloying elements and welding processes.So,in this study,a hybrid machine learning model consisting of multilayer perceptron classifier,k-Nearest Neighbors and random forest is established to predict the phase transformation temperature and hardness of low alloy steel using chemical composition and cooling rate.Then the SH-CCT diagrams of 6 kinds of steels are calculated by the hybrid machine learning model.The results show that the accuracy of the classification model is up to 100%,the predicted values of the regression models are in good agreement with the experimental results,with high correlation coefficient and low error value.Moreover,the mathematical expressions of hardness in welding heat-affected zone of low alloy steel are calculated by symbolic regression,which can quantitatively express the relationship between alloy composition,cooling time and hardness.This study demonstrates the great potential of the material informatics in the field of welding technology.展开更多
The microstructure in welding heat-affected zones of 5 wt.% manganese steels was studied, and its effect on impact toughness was analyzed. The simulated coarse-grained heat-affected zone (CGHAZ) had the lowest impact ...The microstructure in welding heat-affected zones of 5 wt.% manganese steels was studied, and its effect on impact toughness was analyzed. The simulated coarse-grained heat-affected zone (CGHAZ) had the lowest impact toughness of ~39 J at — 40℃ because of coarse-grained structure and least volume fraction of retained austenite (RA) of 1.2 vol.%. The impact toughness of simulated intercritical heat-affected zone (ICHAZ) and fine-grained heat-affected zone (FGHAZ) were ~165 and ~45 J, respectively, at — 40℃. The effective grain size of simulated FGHAZ was smaller than that of the simulated ICHAZ. Furthermore, microstructural investigation revealed that the simulated FGHAZ and ICHAZ had similarity in volume fraction and stability of RA. However, tempered martensite was present in ICHAZ and absent in FGHAZ. It is proposed that the presence of tempered martensite contributed to good impact toughness in simulated ICHAZ.展开更多
Aiming at the requirements of structural steel in Gen-IV nuclear reactor, the high-chromium martensitic heat-resistant steels containing 10–12% chromium were developed. The toughness of heat-affected zones(HAZs) is o...Aiming at the requirements of structural steel in Gen-IV nuclear reactor, the high-chromium martensitic heat-resistant steels containing 10–12% chromium were developed. The toughness of heat-affected zones(HAZs) is one of the important factors for evaluating the weldability of steels. In this paper, the simulated HAZs were fabricated using tempered SIMP steels. The effects of microstructures on the impact toughness of materials were analyzed using Vickers hardness tester, optical microscope, transmission electron microscope. Experimental results demonstrated that the HAZs of weldment were poor in toughness, much lower than that of the base metal. However, after experiencing post-weld heat treatment, the toughness of the HAZs increased greatly. The toughness became better in terms of CG-HAZ, FG-HAZ and IC-HAZ for the two steels, regardless of as-welded or after PWHT. Compared with SIMP7 steel, chemical compositions, such as C, Si, Mn and Cr, were adjusted to a lower content;the toughness of base metal and simulated HAZs was better in the case of SIMP11. The conjunct roles of dislocation density and carbon contents retained in the martensite led to poor impact toughness of the aswelded HAZs, because dislocations and carbon atoms affected the inner stresses within lattices.展开更多
The mechanical properties and microstructure features of the fine-grained heat-affected zone（FGHAZ） of ASTM4130 steel was investigated by optical microscope（OM）,scanning electron microscope（SEM）,transmission ele...The mechanical properties and microstructure features of the fine-grained heat-affected zone（FGHAZ） of ASTM4130 steel was investigated by optical microscope（OM）,scanning electron microscope（SEM）,transmission electron microscope（TEM）,and welding thermal simulation test.It is found that serious embrittlement occurs in the FGHAZ with an 81.37% decrease of toughness,compared with that of the base metal.Microstructure analysis reveals that the FGHAZ is mainly composed of acicular,equiaxed ferrite,granular ferrite,martensite,and martensite-austenite（M-A） constituent.The FGHAZ embrittlement is mainly induced by granular ferrite because of carbides located at its boundaries and sub-boundaries.Meanwhile,the existence of martensite and M-A constituent,which distribute in a discontinuous network,is also detrimental to the mechanical properties.展开更多
In accordance with the minimum degree of disregistry mechanism in oxide metallurgy, the intragranular acicular ferrite (IAF) generated by microalloying elements in austenite was studied. Herein, the effect of Mg treat...In accordance with the minimum degree of disregistry mechanism in oxide metallurgy, the intragranular acicular ferrite (IAF) generated by microalloying elements in austenite was studied. Herein, the effect of Mg treatment on the microstructure and toughness of the heat-affected zone (HAZ) in shipbuilding steel was investigated. Mg treatment produced inclusions that influenced the formation of acicular ferrite in the microstructure. This refined the HAZ microstructure and improved its toughness. Electron backscatter diffraction was used to determine the oxides of titanium and the MgO Al_(2)O_(3) or MgAl_(2)O_(4) complex inclusions that induced the formation of IAF. MnS precipitated on MgAl_(2)O_(4) on a specific habit plane and in a specific direction. MnS had a specific orientation relationship with MgAl_(2)O_(4), i.e., f100gMgAl_(2)O_(4) //{100}MnS. The 35-mm-thick plate obtained in the industrial test after welding at a welding heat input of 120 kJ/cm had an average impact absorbed energy of 282.7 J at - 40 ℃ and 2 mm from the weld joint in the HAZ. The twodimensional disregistry index between inclusions can be used as the basis for controlling their distribution and adsorption force. Microalloy addition in the order of Al-Mg-Ti is key to obtaining abundant dispersion and fine nucleation in austenite.展开更多
Coarse grain heat-affected zone samples of X80 pipeline steel under different heat inputs were obtained through thermal welding simulation experiments with Gleeble 3500.Charpy impact tests and a combination of multisc...Coarse grain heat-affected zone samples of X80 pipeline steel under different heat inputs were obtained through thermal welding simulation experiments with Gleeble 3500.Charpy impact tests and a combination of multiscale characterizations were conducted to investigate the influence of various microstructural features on impact toughness and crack initiation behavior.The results prove that, as the heat input increases, the number of M/A components increases, thereby degrading toughness and increasing hardness.Meanwhile, more M/A constituents tend to aggregate on prior austenite grain boundaries(PAGBs),and the overall dimensions of M/A and the width and volume fraction of the lath martensite substructure inside M/A islands would increase as well.These changes make intersections between boundary M/As and PAGBs become one of the preferred sites for crack initiation.In addition, only large-sized grotesque inclusions can act as a direct inducement of crack initiation.展开更多
EP-823 steel is one of the candidate materials for accelerator-driven systems/lead-cooled fast reactors （ADS/LFR）. Its weldability was investigated by mechanical property tests and microstructure analysis on the enl...EP-823 steel is one of the candidate materials for accelerator-driven systems/lead-cooled fast reactors （ADS/LFR）. Its weldability was investigated by mechanical property tests and microstructure analysis on the enlarged heat-affected zones （HAZs） made by numerical and physical simulation. The finite element numerical simulation could simulate the welding thermal cycle of the characteristic regions in HAZs with extremely high accuracy, The physical simulation performed on a Gleeble simulator could enlarge the characteristic regions to easily investigate the relationship between the microstructure evolution and the mechanical properties of the HAZs. The results showed that the simulated partially normalized zone comprising tempered martensite, newly formed martensite and more tiny carbides has the highest impact energy. The fully normalized zone exhibits the highest hardness because of the quenched martensite and large carbides. The ductile property of the overheated zone is poor for the residual delta- ferrite phases and the quenched martensite.展开更多
The effects of Ca treatment on the particle, microstructure, and toughness of heat-affected zone (HAZ) of shipbuilding steel with Zr-Ti deoxidation after high-heat-input welding were investigated. The simulated weldin...The effects of Ca treatment on the particle, microstructure, and toughness of heat-affected zone (HAZ) of shipbuilding steel with Zr-Ti deoxidation after high-heat-input welding were investigated. The simulated welding at a high-heat-input welding of 200 kJ/cm was carried out using Gleeble-3800 welding simulation. Then, particle characteristics were characterized using an Aztec-Feature automatic particle analysis system. Additionally, an in-situ observation experiment was performed to study the relationships between particle and microstructure by high-temperature confocal laser scanning microscopy (HT-CLSM). The results indicated that the average HAZ toughness at -40 ℃ was increased from 183 to 290 J by adding 0.0026 wt.% Ca. Meanwhile, the formation of acicular ferrite ratio was increased from 49.34% to 60.28% due to the addition of Ca. The scanning electron microscopy results clearly showed that CaO-Al_(2)O_(3)-TiOx-ZrO_(2)-MnS particles could act as effective nucleation sites for the formation of acicular ferrite, which has been verified by the observation of the particle-microstructure relationship under HT-CLSM. Furthermore, particle characterization results show that the cumulative frequency of particles with the size of 1-3 lm was 33.2% in HAZ of Zr-Ti shipbuilding steel but 66.2% in HAZ of Zr-Ti-Ca shipbuilding steel.展开更多
基金support from the National Natural Science Foundation of China (No. U1960202)the Opening Foundation from Shanghai Engineering Research Center of Hot Manufacturing, China (No. 18DZ2253400)。
文摘This work focuses on the influence of Al content on the precipitation of nanoprecipitates,growth of prior austenite grains(PAGs),and impact toughness in simulated coarse-grained heat-affected zones (CGHAZs) of two experimental shipbuilding steels after being subjected to high-heat input welding at 400 kJ·cm^(-1).The base metals (BMs) of both steels contained three types of precipitates Type Ⅰ:cubic (Ti,Nb)(C,N),Type Ⅱ:precipitate with cubic (Ti,Nb)(C,N) core and Nb-rich cap,and Type Ⅲ:ellipsoidal Nb-rich precipitate.In the BM of 60Al and 160Al steels,the number densities of the precipitates were 11.37×10^(5) and 13.88×10^(5) mm^(-2),respectively The 60Al and 160Al steel contained 38.12% and 6.39% Type Ⅲ precipitates,respectively.The difference in the content of Type Ⅲ precipitates in the 60Al steel reduced the pinning effect at the elevated temperature of the CGHAZ,which facilitated the growth of PAGs The average PAG sizes in the CGHAZ of the 60Al and 160Al steels were 189.73 and 174.7μm,respectively.In the 60Al steel,the low lattice mismatch among Cu_(2)S,TiN,and γ-Al_(2)O_(3)facilitated the precipitation of Cu_(2)S and TiN onto γ-Al_(2)O_(3)during welding,which decreased the number density of independently precipitated (Ti,Nb)(C,N) particles but increased that of γ-Al_(2)O_(3)–Ti N–Cu_(2)S particles.Thus abnormally large PAGs formed in the CGHAZ of the 60Al steel,and they reached a maximum size of 1 mm.These PAGs greatly reduced the microstructural homogeneity and consequently decreased the impact toughness from 134 (0.016wt%Al) to 54 J (0.006wt%Al)at-40℃.
基金financially supported by the National Key R&D Program of China(No.2022YFB3705300)the National Natural Science Foundation of China(Nos.U1960204 and 51974199)the Postdoctoral Fellowship Program of CPSF(No.GZB20230515)。
文摘The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.
基金The authors appreciate the financial support from National Key Research and Development Program of China(2017YFBO304900).
文摘The evolution of the microstructure and toughness of APL5L X80 pipeline steel after thermal welding simulation was investigated by X-ray diffraction,electron backscatter diffraction,and transmission electron microscopy.The results indicated that primary heat-affected zones can be divided into weld,coarse-grained,fine-grained,intercritical,and sub-critical zones.The microstructure of the weld zone is mainly composed of bainitic ferrite and a small amount of granular bainite;however,the original austenite grains are distributed in the columnar grains.The structure of the coarse-grained zone is similar to that of the weld zone,but the original austenite grains are equiaxed.In contrast,the microstructure in the fine-grained zone is dominated by fine granular bainite,and the effective grain size is only 8.15μm,thus providing the highest toughness in the entire heat-affected zone.The intercritical and subcritical zones were brittle valley regions,and the microstructure was dominated by granular bainite.However,the martensite-austenite(M/A)constituents are present in island chains along the grain boundaries,and the coarse size of the M/A constituents seriously reduces the toughness.The results of the crack propagation analyzes revealed that high-angle grain boundaries can significantly slow down crack growth and change the crack direction,thereby increasing the material toughness.The impact toughness of the low-temperature tempering zone was equivalent to that of the columnar grain zone,and the impact toughness was between those of the critical and fine-grained zones.
基金Supported by National High Technology Research and Development Program of China(863 Program,Grant No.2015AA042503)K.C.Wong Education Foundation.
文摘Improvement of fabrication efficiency and part performance was the main challenge for the large-scale powder bed fusion(PBF)process.In this study,a dynamic monitoring and feedback system of powder bed temperature field using an infrared thermal imager has been established and integrated into a four-laser PBF equipment with a working area of 2000 mm×2000 mm.The heat-affected zone(HAZ)temperature field has been controlled by adjusting the scanning speed dynamically.Simultaneously,the relationship among spot size,HAZ temperature,and part performance has been established.The fluctuation of the HAZ temperature in four-laser scanning areas was decreased from 30.85℃to 17.41℃.Thus,the consistency of the sintering performance of the produced large component has been improved.Based on the controllable temperature field,a dynamically adjusting strategy for laser spot size was proposed,by which the fabrication efficiency was improved up to 65.38%.The current research results were of great significance to the further industrial applications of large-scale PBF equipment.
基金financially supported by the Postdoctoral Science Foundation of China (No. 2014M550415)the National Natural Science Foundation of China (No. 50734004)
文摘The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then grew in different directions through movement of grain boundaries into the ferrite phase. Subsequently, the adjacent austenite grains impinged against each other during the α→γtransformation. After the α→γ transformation, austenite grains coarsened via the coalescence of small grains and via boundary migration between grains. The growth process of austenite grains was a continuous process during heating, isothermal holding, and cooling in simulated thermal cycling. Abundant finely dispersed nanoscale TiN particles in a steel specimen containing 0.012wt% Ti effectively retarded the grain boundary migration, which resulted in refined austenite grains. When the Ti concentration in the steel was increased, the number of TiN particles de- creased and their size coarsened. The big particles were not effective in pinning the austenite grain boundary movement and resulted in coarse austenite grains.
文摘The effects of Mg content, inclusion size, and austenite grain size on the intragranular acicular ferrite （IAF） nucleation in heat-affected zone of steel plate after high-heat-input welding of 400 kJ/cm were investigated by welding simulation and observation using a scanning electron microscope equipped with an energy dispersive spectrometer and an optical microscope. The IAFs are observed in steel with Mg addition, and the volume fraction of IAF is as high as 55.4% in the steel containing 0.0027 mass% Mg. The MgO-Al2O3-Ti2O3-MnS inclusions with size around 2 μm are effective nucleation sites for IAF, whereas Al2O3-MnS inclusions are impotent to nucleate the acicular ferrite. The prior-austenite grain （PAG） size distribution in low Mg steel is similar to that in steel without Mg addition. The austenite grain with size about 200 μm is favorable for the IAF formation. In the steel with high Mg content of 0.0099%, the growth of PAG is greatly inhibited, and PAG sizes are smaller than 100 μm. Therefore, the nucleation of IAF can hardly be observed.
基金financially supported by the National Environmental Corrosion Platform of China(NECP)the National Key Research and Development Program of China(Nos.2016YFB0300604 and 2017YFB0304701)the National Natural Science Foundation of China(Nos.51771028 and 51871024)。
文摘In this work,the stress corrosion cracking(SCC)behavior of E690 steel base metal(BM)and different heat-affected zone(HAZ)microstructures,i.e.,coarse grain HAZ(CGHAZ),fine grain HAZ(FGHAZ),and intercritical HAZ(ICHAZ),was investigated at different cathodic potentials in artificial seawater by slow strain rate tensile tests,scanning electron microscopy and electron back-scattered diffraction measurements.The results show that the HAZ microstructures and BM exhibit different SCC susceptibilities:FGHAZ<ICHAZ<BM<CGHAZ,which are controlled by anodic dissolution(AD)at the open circuit potential.With the cathodic potential equaling to-750 mV,the SCC susceptibility of the four microstructures increases because of the synergistic effect of AD and weak hydrogen embrittlement(HE).At-850 mV,AD is inhibited,and the SCC susceptibility of BM decreases,while the SCC susceptibility of the HAZ microstructures increases.At a potential below-850 mV,the SCC susceptibility of the four microstructures gradually increases because of the augment of HE,and the SCC susceptibility of the HAZ microstructures is higher than that of BM.The distinction reveals that the HAZ microstructures have the greater HE susceptibility than BM.
文摘The combined influence of Mg and Ca treatment on the properties of heat-affected zone (HAZ) of low-carbon steel after high heat input welding was systematically studied. Experimental steels deoxidized with different elements were prepared, i.e., C-Mn steel with Al, Ti-Ca steel with Ti and Ca, Ti-Mg-Ca steel with Ti, Mg and Ca. Results showed that the inclusions in C-Mn steel were mainly Al2O3 and MnS with low density and large size. However, the average size was refined to only ~0.34 μm in Ti-Mg-Ca steel and the amount increased remarkably. Microstructure of simulated HAZ for 200 kJ/cm changed from ferrite side plates or upper bainite to acicular ferrite after treatment with Ti, Mg and Ca. Ca addition decreased the strain field around inclusions and enhanced the ability of acicular ferrite nucleation. In situ observation of Ti-Mg-Ca steel showed that the movement of austenite grain boundaries was retarded and nucleation sites of acicular ferrite were greater than Ti-Ca steel because of Mg addition. Impact energy of HAZ at — 40℃ was increased from 7 to 232 J and showed excellent stability because of Ti-Mg-Ca treatment. High volume fraction of acicular ferrite acted as obstacles toward cleavage cracks.
基金supported by Key Project of Tianjin Municipal Science and Technology Support Program (No.11ZCGYSF00100)Tianjin Natural Science Foundation (No.11JCYBJC06000)the Gansu province Science and Technology Support Program (No.1204GKCA007)
文摘The intercritical heat-affected zone（ICHAZ） of X80 pipeline steel was simulated by using the Gleeble-3500thermal/mechanical simulator according to the thermal cycle of in-service welding.The microstructures of ICHAZ with different cooling rates were examined,and the hardness,the toughness and corresponding fractography were investigated.Results show that untransformed bainite and ferrite as well as retransformed fine bainite and martensite–austenite（M–A）constituents constitute the microstructure of ICHAZ.The two different morphologies of M–A constituents are stringer and block.Second phase particles which mainly composed of Ti,Nb,C,Fe and Cu coarsened in ICHAZ.Compared with normal welding condition,the toughness of ICHAZ is poor when the cooling time is short under in-service welding condition because of the large area fraction and size of M–A constituents that connect into chains and distribute at the grain boundaries.The Vickers hardness of ICHAZ that decreases with the increase in the cooling time is independent with the area fraction of M–A constituents.
基金financially supported by the National Natural Science Foundation of China(No.51274083)the Natural Science Foundation of Hebei Province(No.E2013209228)+1 种基金the Innovation Team Leading Talent in Universities Cultivation Plan of Hebei Province(No.LJRC007)the Science and Technology Project of Tangshan City(No.131302108b)
文摘The continuous cooling transformation curve of heat-affected zone （HAZ） of X70 pipeline steel was mea- sured by Gleeble-3500 thermal mechanical simulator, optical microscope （OM） and hardness analysis. The microstructure transformation rule at different cooling rates and solution behaviors of microalloy carbonitride during heating process of simulated specimens were investigated. When the cooling rate changes from 10 to 20 ℃.s-l, microstructures at HAZ are identified as granular bainite, lathy bainite, and quasi-polygonal ferrite. This micro- structure is featured with fine ferrite grains, martensite/ austenite islands dispersed, high-density dislocations, and fine carbonitride particles, resulting in improving the strength and toughness of HAZ. With the cooling rate increasing to above 40 ℃.s-1, the microstructure is pre- dominantly coarse lathy bainite with clear primary aus- tenite grain boundary. While the cooling rate decreases to below 1 ℃.s-1, a fairly small amount of pearlite can be observed at the boundaries. The strength and toughness of HAZ are deteriorated because of coarse grains among these microstructures. Most of microalloy carbonitrides in HAZ could be dissolved in the matrix during heating process. A few of TiN particles existing as residues in the matrix can prevent austenite grain from growing, and then improve the strength and toughness of HAZ.
基金the National Natural Science Foundation of China (Grant No.51604072)the Fundamental Research Funds for the Central Universities (Grant No.N170704016)the National High-Tech R&D Program (863 Program)of China (Grant No.2015AA03A501).
文摘The structure-property relationship in heat-affected zone (HAZ)of a low-carbon steel bearing V-N subjected to gasshielded arc welding was explored.The microstructural characteristics of base metal (BM),coarse-grained HAZ (CGHAZ),fine-grained HAZ,and intercritical HAZ were significantly different.The effect of grain-refinement strengthening and transformation hardening on HAZ contributed to equivalent hardness of 260.8-278.5 HV in comparison with BM hardness of 272.0 HV.Moreover,excellent impact toughness at -20 ℃ was obtained because of high resistance to crack propagation by high-misorientation boundaries,leading to impact fracture consisting of dimples.In CGHAZ,free N was partly fixed by V(C,N)precipitates,such that the deterioration effect of N on toughness was considered to be nearly eliminated.In comparison with CGHAZ,weld metal contained higher fraction of acicular ferrite with fine plates,while the impact toughness was inferior because of the detrimental influence of coarse inclusions from the welding wire.The nanoscale V(C,N)precipitates in CGHAZ had weak effect on toughness because of small size.
文摘The main aim of this study was to investigate liquation cracking in the heat-affected zone(HAZ)of the IN939 superalloy upon tungsten inert gas welding.A solid solution and age-hardenable filler metals were further studied.On the pre-weld heat-treated samples,upon solving the secondaryγ′particles in the matrix,primaryγ′particles in the base metal grew to"ogdoadically diced cubes"of about 2μm in side lengths.The pre-weld heat treatment reduced the hardness of the base metal to about HV 310.Microstructural studies using optical and fieldemission scanning electron microscopy revealed that the IN939 alloy was susceptible to liquation cracking in the HAZ.The constitutional melting of the secondary,eutectic,and Zr-rich phases promoted the liquation cracking in the HAZ.The microstructure of the weld fusion zones showed the presence of fine spheroidalγ′particles with sizes of about 0.2μm after the post-weld heat treatment,which increased the hardness of the weld pools to about HV 350 and 380 for the Hastelloy X and IN718 filler metals,respectively.Application of a suitable solid solution filler metal could partially reduce the liquation cracking in the HAZ of IN939 alloy.
基金financial support from the National Key Research and Development Program of China[No.2016YFB0700501]the National Natural Science Foundation of China(No.51571020)。
文摘Continuous cooling transformation diagrams in synthetic weld heat-affected zone(SH-CCT diagrams)show the phase transition temperature and hardness at different cooling rates,which is an important basis for formulating the welding process or predicting the performance of welding heat-affected zone.However,the experimental determination of SH-CCT diagrams is a time-consuming and costly process,which does not conform to the development trend of new materials.In addition,the prediction of SHCCT diagrams using metallurgical models remains a challenge due to the complexity of alloying elements and welding processes.So,in this study,a hybrid machine learning model consisting of multilayer perceptron classifier,k-Nearest Neighbors and random forest is established to predict the phase transformation temperature and hardness of low alloy steel using chemical composition and cooling rate.Then the SH-CCT diagrams of 6 kinds of steels are calculated by the hybrid machine learning model.The results show that the accuracy of the classification model is up to 100%,the predicted values of the regression models are in good agreement with the experimental results,with high correlation coefficient and low error value.Moreover,the mathematical expressions of hardness in welding heat-affected zone of low alloy steel are calculated by symbolic regression,which can quantitatively express the relationship between alloy composition,cooling time and hardness.This study demonstrates the great potential of the material informatics in the field of welding technology.
基金Authors gratefully acknowledge the support from National Natural Science Foundation of China (No. 2015AA03A501).
文摘The microstructure in welding heat-affected zones of 5 wt.% manganese steels was studied, and its effect on impact toughness was analyzed. The simulated coarse-grained heat-affected zone (CGHAZ) had the lowest impact toughness of ~39 J at — 40℃ because of coarse-grained structure and least volume fraction of retained austenite (RA) of 1.2 vol.%. The impact toughness of simulated intercritical heat-affected zone (ICHAZ) and fine-grained heat-affected zone (FGHAZ) were ~165 and ~45 J, respectively, at — 40℃. The effective grain size of simulated FGHAZ was smaller than that of the simulated ICHAZ. Furthermore, microstructural investigation revealed that the simulated FGHAZ and ICHAZ had similarity in volume fraction and stability of RA. However, tempered martensite was present in ICHAZ and absent in FGHAZ. It is proposed that the presence of tempered martensite contributed to good impact toughness in simulated ICHAZ.
文摘Aiming at the requirements of structural steel in Gen-IV nuclear reactor, the high-chromium martensitic heat-resistant steels containing 10–12% chromium were developed. The toughness of heat-affected zones(HAZs) is one of the important factors for evaluating the weldability of steels. In this paper, the simulated HAZs were fabricated using tempered SIMP steels. The effects of microstructures on the impact toughness of materials were analyzed using Vickers hardness tester, optical microscope, transmission electron microscope. Experimental results demonstrated that the HAZs of weldment were poor in toughness, much lower than that of the base metal. However, after experiencing post-weld heat treatment, the toughness of the HAZs increased greatly. The toughness became better in terms of CG-HAZ, FG-HAZ and IC-HAZ for the two steels, regardless of as-welded or after PWHT. Compared with SIMP7 steel, chemical compositions, such as C, Si, Mn and Cr, were adjusted to a lower content;the toughness of base metal and simulated HAZs was better in the case of SIMP11. The conjunct roles of dislocation density and carbon contents retained in the martensite led to poor impact toughness of the aswelded HAZs, because dislocations and carbon atoms affected the inner stresses within lattices.
基金supported by the National High-Tech Research and Development Program of China (No.2006AA09A103-6)
文摘The mechanical properties and microstructure features of the fine-grained heat-affected zone（FGHAZ） of ASTM4130 steel was investigated by optical microscope（OM）,scanning electron microscope（SEM）,transmission electron microscope（TEM）,and welding thermal simulation test.It is found that serious embrittlement occurs in the FGHAZ with an 81.37% decrease of toughness,compared with that of the base metal.Microstructure analysis reveals that the FGHAZ is mainly composed of acicular,equiaxed ferrite,granular ferrite,martensite,and martensite-austenite（M-A） constituent.The FGHAZ embrittlement is mainly induced by granular ferrite because of carbides located at its boundaries and sub-boundaries.Meanwhile,the existence of martensite and M-A constituent,which distribute in a discontinuous network,is also detrimental to the mechanical properties.
基金support from the National Natural Science Foundation of China(Nos.52004094 and 51874137)the Hebei Province Natural Science Fund Project(E2021209037.E2020209044,_and E2020209036)Fundamental Innovation Team of High Quality Clean Stcel in Tangshan_fromTangshan Scienceand Technology Bureau(21130209D).
文摘In accordance with the minimum degree of disregistry mechanism in oxide metallurgy, the intragranular acicular ferrite (IAF) generated by microalloying elements in austenite was studied. Herein, the effect of Mg treatment on the microstructure and toughness of the heat-affected zone (HAZ) in shipbuilding steel was investigated. Mg treatment produced inclusions that influenced the formation of acicular ferrite in the microstructure. This refined the HAZ microstructure and improved its toughness. Electron backscatter diffraction was used to determine the oxides of titanium and the MgO Al_(2)O_(3) or MgAl_(2)O_(4) complex inclusions that induced the formation of IAF. MnS precipitated on MgAl_(2)O_(4) on a specific habit plane and in a specific direction. MnS had a specific orientation relationship with MgAl_(2)O_(4), i.e., f100gMgAl_(2)O_(4) //{100}MnS. The 35-mm-thick plate obtained in the industrial test after welding at a welding heat input of 120 kJ/cm had an average impact absorbed energy of 282.7 J at - 40 ℃ and 2 mm from the weld joint in the HAZ. The twodimensional disregistry index between inclusions can be used as the basis for controlling their distribution and adsorption force. Microalloy addition in the order of Al-Mg-Ti is key to obtaining abundant dispersion and fine nucleation in austenite.
文摘Coarse grain heat-affected zone samples of X80 pipeline steel under different heat inputs were obtained through thermal welding simulation experiments with Gleeble 3500.Charpy impact tests and a combination of multiscale characterizations were conducted to investigate the influence of various microstructural features on impact toughness and crack initiation behavior.The results prove that, as the heat input increases, the number of M/A components increases, thereby degrading toughness and increasing hardness.Meanwhile, more M/A constituents tend to aggregate on prior austenite grain boundaries(PAGBs),and the overall dimensions of M/A and the width and volume fraction of the lath martensite substructure inside M/A islands would increase as well.These changes make intersections between boundary M/As and PAGBs become one of the preferred sites for crack initiation.In addition, only large-sized grotesque inclusions can act as a direct inducement of crack initiation.
基金financial support from the National Natural Science Foundation of China(NSFC)under grant No.91226204the Chinese Academy of Science Strategic Pilot Project(The Future of Advanced Nuclear Energy,ADS Evolution System)under grant No.XDA03010304
文摘EP-823 steel is one of the candidate materials for accelerator-driven systems/lead-cooled fast reactors （ADS/LFR）. Its weldability was investigated by mechanical property tests and microstructure analysis on the enlarged heat-affected zones （HAZs） made by numerical and physical simulation. The finite element numerical simulation could simulate the welding thermal cycle of the characteristic regions in HAZs with extremely high accuracy, The physical simulation performed on a Gleeble simulator could enlarge the characteristic regions to easily investigate the relationship between the microstructure evolution and the mechanical properties of the HAZs. The results showed that the simulated partially normalized zone comprising tempered martensite, newly formed martensite and more tiny carbides has the highest impact energy. The fully normalized zone exhibits the highest hardness because of the quenched martensite and large carbides. The ductile property of the overheated zone is poor for the residual delta- ferrite phases and the quenched martensite.
基金supported by the Open Project Program of Bejing Key Laboratory of Pipeline Critical Technology and Equipment forDeepwater Oil&Gas Development(Grant No.BIPT2019001)the Natural Science Foundation of Hebei Province(Grant No.E2021318004)。
文摘The effects of Ca treatment on the particle, microstructure, and toughness of heat-affected zone (HAZ) of shipbuilding steel with Zr-Ti deoxidation after high-heat-input welding were investigated. The simulated welding at a high-heat-input welding of 200 kJ/cm was carried out using Gleeble-3800 welding simulation. Then, particle characteristics were characterized using an Aztec-Feature automatic particle analysis system. Additionally, an in-situ observation experiment was performed to study the relationships between particle and microstructure by high-temperature confocal laser scanning microscopy (HT-CLSM). The results indicated that the average HAZ toughness at -40 ℃ was increased from 183 to 290 J by adding 0.0026 wt.% Ca. Meanwhile, the formation of acicular ferrite ratio was increased from 49.34% to 60.28% due to the addition of Ca. The scanning electron microscopy results clearly showed that CaO-Al_(2)O_(3)-TiOx-ZrO_(2)-MnS particles could act as effective nucleation sites for the formation of acicular ferrite, which has been verified by the observation of the particle-microstructure relationship under HT-CLSM. Furthermore, particle characterization results show that the cumulative frequency of particles with the size of 1-3 lm was 33.2% in HAZ of Zr-Ti shipbuilding steel but 66.2% in HAZ of Zr-Ti-Ca shipbuilding steel.
