Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to subs...Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to substitute part of road tests for designing,testing,and tuning electronic control units（ECUs） of ABS.Most HILS systems for ABS use expensive digital signal processor hardware and special purpose software,and some fail-safe functions with regard to wheel speeds cannot be evaluated since artificial wheel speed signals are usually provided.In this paper,a low-cost ABS HILS test bench is developed and used for validating the anti-lock braking performance and tuning control parameters of ABS controllers.Another important merit of the proposed test bench is that it can comprehensively evaluate the fail-safe functions with regard to wheel speed signals since real tone rings and sensors are integrated in the bench.A 5-DOF vehicle model with consideration of longitudinal load transfer is used to calculate tire forces,wheel speeds and vehicle speed.Each of the four real-time wheel speed signal generators consists of a servo motor plus a ring gear,which has sufficient dynamic response ability to emulate the rapid changes of the wheel speeds under strict braking conditions of very slippery roads.The simulation of braking tests under different road adhesion coefficients using the HILS test bench is run,and results show that it can evaluate the anti-lock braking performance of ABS and partly the fail-safe functions.This HILS system can also be used in such applications as durability test,benchmarking and comparison between different ECUs.The test bench developed not only has a relatively low cost,but also can be used to validate the wheel speed-related ECU design and all its fail-safe functions,and a rapid testing and proving platform with a high efficiency for research and development of the automotive ABS is therefore provided.展开更多
As friction, intrinsic steady-state nonlinearity poses a challenging dilemma to the control system of 3-DOF （three degree of freedom） flight simulator, a novel hybrid control strategy of nonlinear PID （proportional...As friction, intrinsic steady-state nonlinearity poses a challenging dilemma to the control system of 3-DOF （three degree of freedom） flight simulator, a novel hybrid control strategy of nonlinear PID （proportionalintegral-derivative） with additional FFC （feed-forward controller） is proposed, and the hardware-in-the-loop simulation results are also given. Based on the description of 3-DOF flight simulator, a novel nonlinear PID theory is well introduced. Then a nonlinear PID controller with additional FFC is designed. Subsequently, the loop structure of 3-DOF flight simulator is also designed. Finally, a series of hardware-in-the-loop simulation experiments are undertaken to verify the feasibility and effectiveness of the proposed nonlinear PID controller with additional FFC for 3-DOF flight simulator.展开更多
Beer fermentation process is a complex biochemical reaction process.It is the most important to control temperature of the wort in fermentation tank in accordance with the beer fermentation temperature curve so as to ...Beer fermentation process is a complex biochemical reaction process.It is the most important to control temperature of the wort in fermentation tank in accordance with the beer fermentation temperature curve so as to ensure the completion of fermentation.The controlled object is characterized by large inertia,long time delay and mutual coupling of three temperature areas.Based on this,a temperature control method for beer fermentation system is designed.Using digital incremental proportion integration differentiation （PID） control algorithm,the controlled quantity is transmitted to the controlled object after diagonal matrix decoupling.This simulation system can be completed in laboratory using VB and Kingview software,so it has the features of good security and low cost.It is very suitable for experimental teaching.展开更多
A manipulator-type docking hardware-in-the-loop(HIL)simulation system is proposed in this paper,with further development of the space docking technology and corresponding requirements of the engineering project.First,...A manipulator-type docking hardware-in-the-loop(HIL)simulation system is proposed in this paper,with further development of the space docking technology and corresponding requirements of the engineering project.First,the structure of the manipulator-type HIL simulation system is explained.The mass and the flexibility of the manipulator has an important influence on the stability of the HIL system,which is the premise of accurately simulating actual space docking.Thus,the docking HIL simulation models of rigid,flexible and flexible-light space manipulators are established.The characteristics of the three HIL systems are studied from three important aspects:the system parameter configuration relation,the system stability condition and the dynamics frequency simulation ability.The key conclusions obtained were that the system satisfies stability or reproduction accuracy.Meanwhile,the influence of different manipulators on the system stability is further analyzed.The accuracy of the calculated results is verified experimentally.展开更多
A ground-based hardware-in-the-loop （HIL） simulation system with hydraulically driven Stewart platform for spacecraft docking simulation is presented. The system is used for simulating docking process of the on-orbi...A ground-based hardware-in-the-loop （HIL） simulation system with hydraulically driven Stewart platform for spacecraft docking simulation is presented. The system is used for simulating docking process of the on-orbit spacecraft. Principle and structure of the six-degree-of-freedom simulation system are introduced. The docking process dynamic of the vehicles is modeled. Experiment results and mathematical simulation data are compared to validating the simulation system. The comparisons of the results prove that the simulation system proposed can effectively simulate the on-orbit docking process of the spacecraft.展开更多
To enhance the fidelity and accuracy of the simulation of communication networks,hardware-in-the-loop（HITL） simulation was employed.HITL simulation methods was classified into three categories,of which the merits an...To enhance the fidelity and accuracy of the simulation of communication networks,hardware-in-the-loop（HITL） simulation was employed.HITL simulation methods was classified into three categories,of which the merits and shortages were compared.Combing system-in-the-loop（SITL） simulation principle with high level architecture（HLA）,an HITL simulation model of asynchronous transfer mode（ATM） network was constructed.The throughput and end-to-end delay of all-digital simulation and HITL simulation was analyzed,which showed that HITL simulation was more reliable and effectively improved the simulation credibility of communication network.Meanwhile,HLA-SITL method was fast and easy to achieve and low-cost during design lifecycle.Thus,it was a feasible way to research and analyze the large-scale network.展开更多
A simple and economical method based on dSPACE system is developed to measure the effect of cable vibration control.The experiments,numerical simulation and hardware-in-the-loop(HIL)simulation are carried out for the ...A simple and economical method based on dSPACE system is developed to measure the effect of cable vibration control.The experiments,numerical simulation and hardware-in-the-loop(HIL)simulation are carried out for the vibration control of stay cables with dampers.Firstly,the test results of solid cable vibration under harmonic excitation are compared with the numerical simulation results of cable vibration to ensure the correctness of the simulation of cable module.Then,the vibration test results of solid cable with damper under harmonic excitation are compared with the numerical simulation results of solid cable with damper to ensure the correctness of the relevant modules.Finally,the external load and the cable are imported into the real-time simulation system to simulate the control effect of the damper under the current excitation in real time.The results show that the simulation is correct and the HIL simulation is feasible in the bridge engineering.展开更多
In the large-scale distributed hardware-in-the-loop radar simulation system based on HLA, a new solution of processing after acquisition is proposed, which separates the software subsystem from the hardware jammer sub...In the large-scale distributed hardware-in-the-loop radar simulation system based on HLA, a new solution of processing after acquisition is proposed, which separates the software subsystem from the hardware jammer subsystem by a response database, so as to settle the problem, that the software subsystem can not meet the real-time need of the hardware, with very little increment of code. And the data completeness and feasibility of this solution are discussed.展开更多
It is considered as an important and effective means to give priority to the development of public transit which can improve the efficiency of transportation resources utilization and alleviate traffic jams. Public tr...It is considered as an important and effective means to give priority to the development of public transit which can improve the efficiency of transportation resources utilization and alleviate traffic jams. Public transit signal priority belongs to the "time priority" among the right-of-way priorities. After reviewing the existing bus priority signal control strategies and the advances in related technologies at home and abroad, this article analyzed the breakthrough direction of the bus signal priority design technologies suitable for China's conditions, and then proposed the hardware and software systems and the modules for the bus priority signal control system. Finally, the hardware-in-the-loop simulation (HILS) was introduced to evaluate bus priority signal control programs in order to optimize the control strategies.展开更多
Aeropropulsion System Test Facility (ASTF) is required to accurately control the pressure and temperature of the airflow to test the performance of the aero-engine. However, the control accuracy of ASTF is significant...Aeropropulsion System Test Facility (ASTF) is required to accurately control the pressure and temperature of the airflow to test the performance of the aero-engine. However, the control accuracy of ASTF is significantly affected by the flow disturbance caused by aero-engine acceleration and deceleration. This would reduce the credibility of ASTF’s test results for the aero-engine. Therefore, first, this paper proposes a feedforward compensation-based L1 adaptive control method for ASTF to address this problem. The baseline controller is first designed based on ideal uncoupled closed-loop dynamics to achieve dynamic decoupling. Then, L1 adaptive control is adopted to deal with various uncertainties and ensure good control performance. To further enhance the anti-disturbance performance, a feedforward strategy based on disturbance prediction is designed in the L1 adaptive control framework to compensate for the unmatched flow disturbance, which cannot be measured directly. In addition, this strategy takes into account the effects of actuator dynamics. With this method, the feedforward term can be determined from the nominal model parameters despite uncertainties. Finally, to demonstrate the effectiveness of the proposed method, various comparative experiments are performed on a hardware-in-the-loop system of ASTF. The experimental results show that the proposed method possesses excellent tracking performance, anti-disturbance performance and robustness.展开更多
The present paper deals with the development of a modular, flexible and structured block to block approach for the study of regulators by implementing the different blocks on a DSP （digital signal processor）. The pr...The present paper deals with the development of a modular, flexible and structured block to block approach for the study of regulators by implementing the different blocks on a DSP （digital signal processor）. The proposed low-cost approach has been applied and validated by the implementation of an industrial regulator in a real time hardware-in-the-loop simulation of a mixed islanded power network including precise models of the hydraulic system. The studied network is constituted of three different types of electrical power generation systems and a consumer.展开更多
For the research of mobile Ad hoc network (MANET), hardware in the loop simulation (HILS) is introduced to improve simulation fidelity. The architectures and frameworks of HILS system are discussed. Based on HILS and ...For the research of mobile Ad hoc network (MANET), hardware in the loop simulation (HILS) is introduced to improve simulation fidelity. The architectures and frameworks of HILS system are discussed. Based on HILS and QualNet network simulator, two kinds of simulation frameworks for MANET multicast emergency communication network are proposed. By running simulation under this configuration and doing experiments with on-demand multicast routing protocol (ODMRP), unicast and multicast functions of this protocol are tested. Research results indicate that HILS method can effectively reduce the difficulty of system modeling and improve precision of simulation, and can further accelerate transition from design to system deployment.展开更多
An investigation into the aircraft flight simulation and control system is presented in this paper. The study was firstly focused on the establishment of an integrated hardware-in-the-loop（HITL） platform for aircraf...An investigation into the aircraft flight simulation and control system is presented in this paper. The study was firstly focused on the establishment of an integrated hardware-in-the-loop（HITL） platform for aircraft flight simulation based on MATLAB/Simulink ＋ dSPACE. The platform combines the abundant software and hardware resources of dSPACE simulation platform to simulate the flight attitude of an aircraft in six-DOF （ degree of freedom） motion. Based on the platform, the study was then focused on the flight numerical simulation by taking a loitering aerial vehicle as an example. An aircraft mathematical model was created for a modular design and off-line numerical simulation based on MATLAB/Simulink. Finally, the study was focused on the control system design of the loitering aerial vehicle and conduct of an HITL simulation experiment for the vehicle pitch control. The experiment verifies the system design and control effectiveness. Research results show that the dSPACE simulation system provides a real time good experimental platform to improve the efficiency of study and development of a flight control system.展开更多
AC-HVDC-AC energy conversion systems using MMC （modular multilevel converters） are becoming popular to integrate distributed energy systems to the main grid. Such multilevel converters pose a serious problems for H...AC-HVDC-AC energy conversion systems using MMC （modular multilevel converters） are becoming popular to integrate distributed energy systems to the main grid. Such multilevel converters pose a serious problems for HIL （hardware in the loop） simulators required for control, protection design and testing due to the large number of cells that must be simulated individually using very small time steps. This paper demonstrates the advantages of using a very small time step to simulate a MMC topology. The MMC is implemented on FPGA （fiel-programmable gate array） to simulate fast transient with a time step of 250 ns. The AC network and HVDC bus is simulated on the PC, with a slower time step of 10 μs to 20 μs. The simulator architecture and the components simulated on the FPGA and on the PC will be discussed, as well as the method allowing the interconnection of this slow and fast system.展开更多
Developing the control of modem power converters is a very expensive and time-consuming task. Time to market can take unacceptable long. FPGA-based real-time simulation of a power stage with analog measured signals ca...Developing the control of modem power converters is a very expensive and time-consuming task. Time to market can take unacceptable long. FPGA-based real-time simulation of a power stage with analog measured signals can reduce significantly the cost and time of testing a product. This new approach is known as HIL （hardware-in-the-loop） testing. A general power converter consists of two main parts： a power level （main circuit） and a digital controller unit, which is usually realized by using some kind of DSP. Testing the controller HW and SW is quite problematic： live tests with a completely assembled converter can be dangerous and expensive. A low-power model of the main circuit can be built under laboratory conditions, but it will have parameters （e.g. time constants and relative losses） differing from the ones of the original system. The solution is the HIL simulation of the main circuit. With this method the simulator can be completely transparent for the controller unit, unlike other computer based simulation methods The subject of this paper is to develop such a real-time simulator using FPGA. The modeled circuit is a three-phase inverter, which is widely used in power converters of renewable energy sources.展开更多
基金supported by National Natural Science Foundation of China(Grant No.50908008)National Hi-tech Research and Development Program of China(863Program,Grant No.2009AA11Z216)
文摘Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to substitute part of road tests for designing,testing,and tuning electronic control units（ECUs） of ABS.Most HILS systems for ABS use expensive digital signal processor hardware and special purpose software,and some fail-safe functions with regard to wheel speeds cannot be evaluated since artificial wheel speed signals are usually provided.In this paper,a low-cost ABS HILS test bench is developed and used for validating the anti-lock braking performance and tuning control parameters of ABS controllers.Another important merit of the proposed test bench is that it can comprehensively evaluate the fail-safe functions with regard to wheel speed signals since real tone rings and sensors are integrated in the bench.A 5-DOF vehicle model with consideration of longitudinal load transfer is used to calculate tire forces,wheel speeds and vehicle speed.Each of the four real-time wheel speed signal generators consists of a servo motor plus a ring gear,which has sufficient dynamic response ability to emulate the rapid changes of the wheel speeds under strict braking conditions of very slippery roads.The simulation of braking tests under different road adhesion coefficients using the HILS test bench is run,and results show that it can evaluate the anti-lock braking performance of ABS and partly the fail-safe functions.This HILS system can also be used in such applications as durability test,benchmarking and comparison between different ECUs.The test bench developed not only has a relatively low cost,but also can be used to validate the wheel speed-related ECU design and all its fail-safe functions,and a rapid testing and proving platform with a high efficiency for research and development of the automotive ABS is therefore provided.
基金the National Natural Science Foundation of China (60604009)Aeronautical Science Foundationof China(2006ZC51039)Beijing NOVA Program (2007A017).
文摘As friction, intrinsic steady-state nonlinearity poses a challenging dilemma to the control system of 3-DOF （three degree of freedom） flight simulator, a novel hybrid control strategy of nonlinear PID （proportionalintegral-derivative） with additional FFC （feed-forward controller） is proposed, and the hardware-in-the-loop simulation results are also given. Based on the description of 3-DOF flight simulator, a novel nonlinear PID theory is well introduced. Then a nonlinear PID controller with additional FFC is designed. Subsequently, the loop structure of 3-DOF flight simulator is also designed. Finally, a series of hardware-in-the-loop simulation experiments are undertaken to verify the feasibility and effectiveness of the proposed nonlinear PID controller with additional FFC for 3-DOF flight simulator.
基金Shandong Province Department of Education Science and Technology Program(No.J05C11)
文摘Beer fermentation process is a complex biochemical reaction process.It is the most important to control temperature of the wort in fermentation tank in accordance with the beer fermentation temperature curve so as to ensure the completion of fermentation.The controlled object is characterized by large inertia,long time delay and mutual coupling of three temperature areas.Based on this,a temperature control method for beer fermentation system is designed.Using digital incremental proportion integration differentiation （PID） control algorithm,the controlled quantity is transmitted to the controlled object after diagonal matrix decoupling.This simulation system can be completed in laboratory using VB and Kingview software,so it has the features of good security and low cost.It is very suitable for experimental teaching.
基金Supported by the National Natural Science Foundation of China(51475116)。
文摘A manipulator-type docking hardware-in-the-loop(HIL)simulation system is proposed in this paper,with further development of the space docking technology and corresponding requirements of the engineering project.First,the structure of the manipulator-type HIL simulation system is explained.The mass and the flexibility of the manipulator has an important influence on the stability of the HIL system,which is the premise of accurately simulating actual space docking.Thus,the docking HIL simulation models of rigid,flexible and flexible-light space manipulators are established.The characteristics of the three HIL systems are studied from three important aspects:the system parameter configuration relation,the system stability condition and the dynamics frequency simulation ability.The key conclusions obtained were that the system satisfies stability or reproduction accuracy.Meanwhile,the influence of different manipulators on the system stability is further analyzed.The accuracy of the calculated results is verified experimentally.
文摘A ground-based hardware-in-the-loop （HIL） simulation system with hydraulically driven Stewart platform for spacecraft docking simulation is presented. The system is used for simulating docking process of the on-orbit spacecraft. Principle and structure of the six-degree-of-freedom simulation system are introduced. The docking process dynamic of the vehicles is modeled. Experiment results and mathematical simulation data are compared to validating the simulation system. The comparisons of the results prove that the simulation system proposed can effectively simulate the on-orbit docking process of the spacecraft.
基金Supported by the National Natural Science Foundation of China (61101129)Specialized Research Fund for the Doctoral Program of Higher Education(20091101110019)
文摘To enhance the fidelity and accuracy of the simulation of communication networks,hardware-in-the-loop（HITL） simulation was employed.HITL simulation methods was classified into three categories,of which the merits and shortages were compared.Combing system-in-the-loop（SITL） simulation principle with high level architecture（HLA）,an HITL simulation model of asynchronous transfer mode（ATM） network was constructed.The throughput and end-to-end delay of all-digital simulation and HITL simulation was analyzed,which showed that HITL simulation was more reliable and effectively improved the simulation credibility of communication network.Meanwhile,HLA-SITL method was fast and easy to achieve and low-cost during design lifecycle.Thus,it was a feasible way to research and analyze the large-scale network.
基金National Natural Science Foundation of China(No.50178430)。
文摘A simple and economical method based on dSPACE system is developed to measure the effect of cable vibration control.The experiments,numerical simulation and hardware-in-the-loop(HIL)simulation are carried out for the vibration control of stay cables with dampers.Firstly,the test results of solid cable vibration under harmonic excitation are compared with the numerical simulation results of cable vibration to ensure the correctness of the simulation of cable module.Then,the vibration test results of solid cable with damper under harmonic excitation are compared with the numerical simulation results of solid cable with damper to ensure the correctness of the relevant modules.Finally,the external load and the cable are imported into the real-time simulation system to simulate the control effect of the damper under the current excitation in real time.The results show that the simulation is correct and the HIL simulation is feasible in the bridge engineering.
基金the Ministerial Level Advanced Research Foundation
文摘In the large-scale distributed hardware-in-the-loop radar simulation system based on HLA, a new solution of processing after acquisition is proposed, which separates the software subsystem from the hardware jammer subsystem by a response database, so as to settle the problem, that the software subsystem can not meet the real-time need of the hardware, with very little increment of code. And the data completeness and feasibility of this solution are discussed.
基金supported in part by National Basic Research Program of China (2006CB705500)National Natural Science Foundation of China (No.50738001)Outstanding Young Teachers Teaching and Research Funding Program of Southeast University
文摘It is considered as an important and effective means to give priority to the development of public transit which can improve the efficiency of transportation resources utilization and alleviate traffic jams. Public transit signal priority belongs to the "time priority" among the right-of-way priorities. After reviewing the existing bus priority signal control strategies and the advances in related technologies at home and abroad, this article analyzed the breakthrough direction of the bus signal priority design technologies suitable for China's conditions, and then proposed the hardware and software systems and the modules for the bus priority signal control system. Finally, the hardware-in-the-loop simulation (HILS) was introduced to evaluate bus priority signal control programs in order to optimize the control strategies.
基金supported by the“Shuimu Tsinghua Scholar”Project,China(No.2024SM223)the National Science and Technology Major Project,China(No.Y2022-V-0002-0028).
文摘Aeropropulsion System Test Facility (ASTF) is required to accurately control the pressure and temperature of the airflow to test the performance of the aero-engine. However, the control accuracy of ASTF is significantly affected by the flow disturbance caused by aero-engine acceleration and deceleration. This would reduce the credibility of ASTF’s test results for the aero-engine. Therefore, first, this paper proposes a feedforward compensation-based L1 adaptive control method for ASTF to address this problem. The baseline controller is first designed based on ideal uncoupled closed-loop dynamics to achieve dynamic decoupling. Then, L1 adaptive control is adopted to deal with various uncertainties and ensure good control performance. To further enhance the anti-disturbance performance, a feedforward strategy based on disturbance prediction is designed in the L1 adaptive control framework to compensate for the unmatched flow disturbance, which cannot be measured directly. In addition, this strategy takes into account the effects of actuator dynamics. With this method, the feedforward term can be determined from the nominal model parameters despite uncertainties. Finally, to demonstrate the effectiveness of the proposed method, various comparative experiments are performed on a hardware-in-the-loop system of ASTF. The experimental results show that the proposed method possesses excellent tracking performance, anti-disturbance performance and robustness.
文摘The present paper deals with the development of a modular, flexible and structured block to block approach for the study of regulators by implementing the different blocks on a DSP （digital signal processor）. The proposed low-cost approach has been applied and validated by the implementation of an industrial regulator in a real time hardware-in-the-loop simulation of a mixed islanded power network including precise models of the hydraulic system. The studied network is constituted of three different types of electrical power generation systems and a consumer.
文摘For the research of mobile Ad hoc network (MANET), hardware in the loop simulation (HILS) is introduced to improve simulation fidelity. The architectures and frameworks of HILS system are discussed. Based on HILS and QualNet network simulator, two kinds of simulation frameworks for MANET multicast emergency communication network are proposed. By running simulation under this configuration and doing experiments with on-demand multicast routing protocol (ODMRP), unicast and multicast functions of this protocol are tested. Research results indicate that HILS method can effectively reduce the difficulty of system modeling and improve precision of simulation, and can further accelerate transition from design to system deployment.
基金Sponsored by the Ministerial Level Advanced Research Foundation(A26020060253)
文摘An investigation into the aircraft flight simulation and control system is presented in this paper. The study was firstly focused on the establishment of an integrated hardware-in-the-loop（HITL） platform for aircraft flight simulation based on MATLAB/Simulink ＋ dSPACE. The platform combines the abundant software and hardware resources of dSPACE simulation platform to simulate the flight attitude of an aircraft in six-DOF （ degree of freedom） motion. Based on the platform, the study was then focused on the flight numerical simulation by taking a loitering aerial vehicle as an example. An aircraft mathematical model was created for a modular design and off-line numerical simulation based on MATLAB/Simulink. Finally, the study was focused on the control system design of the loitering aerial vehicle and conduct of an HITL simulation experiment for the vehicle pitch control. The experiment verifies the system design and control effectiveness. Research results show that the dSPACE simulation system provides a real time good experimental platform to improve the efficiency of study and development of a flight control system.
文摘AC-HVDC-AC energy conversion systems using MMC （modular multilevel converters） are becoming popular to integrate distributed energy systems to the main grid. Such multilevel converters pose a serious problems for HIL （hardware in the loop） simulators required for control, protection design and testing due to the large number of cells that must be simulated individually using very small time steps. This paper demonstrates the advantages of using a very small time step to simulate a MMC topology. The MMC is implemented on FPGA （fiel-programmable gate array） to simulate fast transient with a time step of 250 ns. The AC network and HVDC bus is simulated on the PC, with a slower time step of 10 μs to 20 μs. The simulator architecture and the components simulated on the FPGA and on the PC will be discussed, as well as the method allowing the interconnection of this slow and fast system.
文摘Developing the control of modem power converters is a very expensive and time-consuming task. Time to market can take unacceptable long. FPGA-based real-time simulation of a power stage with analog measured signals can reduce significantly the cost and time of testing a product. This new approach is known as HIL （hardware-in-the-loop） testing. A general power converter consists of two main parts： a power level （main circuit） and a digital controller unit, which is usually realized by using some kind of DSP. Testing the controller HW and SW is quite problematic： live tests with a completely assembled converter can be dangerous and expensive. A low-power model of the main circuit can be built under laboratory conditions, but it will have parameters （e.g. time constants and relative losses） differing from the ones of the original system. The solution is the HIL simulation of the main circuit. With this method the simulator can be completely transparent for the controller unit, unlike other computer based simulation methods The subject of this paper is to develop such a real-time simulator using FPGA. The modeled circuit is a three-phase inverter, which is widely used in power converters of renewable energy sources.
