The BZ oilfield in the Bohai Sea is a rare,highly volatile reservoir with fractures in the metamorphic rocks of buried hills.Clarifying the mechanism of gas injection for improving oil recovery and determining the opt...The BZ oilfield in the Bohai Sea is a rare,highly volatile reservoir with fractures in the metamorphic rocks of buried hills.Clarifying the mechanism of gas injection for improving oil recovery and determining the optimal way to deploy injection-production well networks are critical issues that must be urgently addressed for efficient oilfield development.Experimental research on the mixed-phase displacement mechanism through gas injection into indoor formation fluids was conducted to guide the efficient development of gas injection in oil fields.We established a model of dual-medium reservoir composition and researched the deployment strategy for a three-dimensional well network for gas injection development.The coupling relationship between key influencing factors of the well network and fracture development was also quantitatively analyzed.The results show that the solubility of the associated gas and strong volatile oil system injected into the BZ oilfield is high.This high solubility demonstrates a mixed-phase displacement mechanism involving intermediate hydrocarbons,dissolution and condensation of medium components,and coexistence of extraction processes.Injecting gas and crude oil can achieve a favorable mixing effect when the local formation pressure is greater than 35.79 MPa.Associated gas reinjection is recommended to supplement energy for developing the highly volatile oil reservoirs in the fractured buried hills of the BZ oilfield.This recommendation involves fully utilizing the structural position and gravity-assisted oil displacement mechanism to deploy an injection-production well network.Gas injection points should be constructed at the top of high areas,and oil production points should be placed at the middle and lower parts of low areas.This approach forms a spatial threedimensional well network.By adopting high inclination well development,the oil production well forms a 45°angle with the fracture direction,which increases the drainage area and enhances single-well production capacity.The optimal injection-production well spacing along the fracture direction is approximately 1000 m,while the reasonable well spacing in the vertical fracture direction is approximately 800 m.The research results were applied to the development practice of the buried hills in the BZ oilfield,which achieved favorable development results.These outcomes provide a valuable reference for the formulation of development plans and efficient gas injection development in similar oil and gas fields in buried hills.展开更多
Optimal spacing for vertical wells can be effectively predicted with several published methods,but methods suitable for assessing the proper horizontal well spacing are rare.This work proposes a method for calculating...Optimal spacing for vertical wells can be effectively predicted with several published methods,but methods suitable for assessing the proper horizontal well spacing are rare.This work proposes a method for calculating the optimal horizontal well spacing for an ultra-low permeability reservoir e the Yongjin reservoir in the Juggar Basin,northwestern China.The result shows that a spacing of 640m is the most economical for the development of the reservoir.To better develop the reservoir,simulation approaches are used and a new model is built based on the calculated well spacing.Since the reservoir has an ultralow permeability,gas injection is regarded as the preferred enhanced oil recovery(EOR)method.Injection of different gases including carbon dioxide,methane,nitrogen and mixed gas are modelled.The results show that carbon dioxide injection is the most efficient and economical for the development of the reservoir.However,if the reservoir produces enough methane,reinjecting methane is even better than injecting carbon dioxide.展开更多
Low thermal evolution degree of gas and connected fracture network are key features in the continental shale gas reservoirs.When the pressure decreases lower than the dew point pressure,gas condensate diminishes the m...Low thermal evolution degree of gas and connected fracture network are key features in the continental shale gas reservoirs.When the pressure decreases lower than the dew point pressure,gas condensate diminishes the mobility of subsurface fluid forms in the near well region,which further reduces the productivity and final recovery factor in addition to the low connected fracture network.This work is motivated to investigate the application of gas injection,proven to be a feasible technique in conventional/marine-shale gas condensate reservoirs,in continental shale gas condensate reservoirs.We apply a compositional model to investigate the mechanism of gas injection treatment taking a continental shale gas condensate reservoir in the Fuxing area,Sichuan Basin,China as an example.The results demonstrate that for the removal of gas condensate during CO_(2)injection,re-vaporization plays the main mechanism through two processes including pressurization and development of miscibility,while the former is overwhelming.Considering the variation trend of the total volume of gas condensate,we divide the whole injection process into four and six stages in the single fracture model and fracture network model,respectively,and reason the trend with respect to phase behavior and flow pattern.A sensitive study on the injected gas type indicates that the sorting of the gas injection performance to remove gas condensate produced gas followed by CH_(4),and followed by CO_(2).Finally,we investigate the performance of cyclic produced-gas injection and optimize the injection scheme.This work provides technical and theoretical support for the development of continental shale gas reservoirs.展开更多
In gas injection refining processes,wide dispersion of small bubbles in the bath is indispensable for high refining efficiency.Eccentric mechanical stirring with unidirectional impeller rotation was tested using a wat...In gas injection refining processes,wide dispersion of small bubbles in the bath is indispensable for high refining efficiency.Eccentric mechanical stirring with unidirectional impeller rotation was tested using a water model for pursuing better bubble disintegration and dispersion.Effects of various factors on bubble disintegration and dispersion were investigated.These factors were stirring mode,eccentricity and rotation speed,nozzle structure,nozzle immersion depth,and gas flow rate.Gas injection from a nozzle at the end of the impeller shaft and from an immersed lance was studied.Under eccentric stirring,a vortex was formed away from the shaft.Small bubbles were produced in the strong turbulence or high shear stress field near the rotating impeller and moved in the direction to the vortex keeping up with the macroscopic flow induced by the mechanical stirring.Thus small bubbles could disperse widely in the bath under eccentric stirring with unidirectional rotation.展开更多
Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical ...Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical microscopy,scanning electron microscopy（SEM） and Auger electron spectroscopy（AES） were used to analyze the influence of oxygen content on cell structure,relative density,macro and micro morphology of cell walls,coverage area fraction of oxide film,thickness of oxide film and other aspects.Results indicate that the coverage area fraction of oxide film on bubble surface increases with the increase of oxygen content when the oxygen volume is less than 1.2%.While when the oxygen volume fraction is larger than 1.6%,an oxide film covers the entire bubble surface and aluminum foams with good cell structure can be produced.The thicknesses of oxide films of aluminum foams produced by gas mixtures containing 1.6%-21%oxygen are almost the same.The reasons why the thickness of oxide film nearly does not change with the variation of oxygen content and the amount of oxygen needed to achieve 100%coverage of oxide film are both discussed.In addition,the role of oxide film on bubble surface in foam stability is also analyzed.展开更多
In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron ...In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron spectroscopy （AES） was used. Based on the knowledge of corrosion science and hydrodynamics, two oxidation kinetics models of oxide film on bubble surface were established. The thicknesses of oxide films produced at different temperatures were predicted through those two models. Furthermore, the theoretical values were compared with the experimental values. The results indicate that in the range of 620？710 °C, the theoretical values of the thickness of oxide film predicted by the model including the rising process are higher than the experimental values. While, the theoretical values predicted by the model without the rising process are in good agreement with the experimental values, which shows this model objectively describes the oxidation process of oxide film on bubble surface. This work suggests that the oxidation kinetics of oxide film on bubble surface of aluminum foams produced by gas injection foaming process follows the Arrhenius equation.展开更多
The flow field of molten steel and the interfacial behaviour between molten steel and liquid slag layer in medium-thin slab continuous casting mold with argon gas injection were studied by numerical simulation, in whi...The flow field of molten steel and the interfacial behaviour between molten steel and liquid slag layer in medium-thin slab continuous casting mold with argon gas injection were studied by numerical simulation, in which the effects of nozzle submergence depth and port angle, casting speed, and argon gas flow rate on the flow and the level fluctuation of molten steel were considered. The results show that the molten steel is jetted from the submerged en- try nozzle （SEN） with three ports into the mold and forms three recirculation zones including one upper recireulation zone and two lower recirculation zones. Argon gas injection results in a secondary vortex flow in the upper zone near the nozzle. For a given casting speed and argon gas flow rate, increasing the side port angle and submergence depth of nozzle can effectively restrain the steel/slag interracial fluctuation. Increasing the casting speed would prick up the level fluctuation. For a fixed casting speed, argon gas flow rate has a critical value, the interracial fluctuation with argon gas injection are stronger than the case without argon gas injection when the argon gas flow rate is less than the critical value, but when the argon gas flow rate exceeds the critical value, the level fluctuation is calmer than that without argon gas injection.展开更多
Gas injection serves as a main enhanced oil recovery(EOR)method in fractured-vuggy carbonate reservoir,but its effect differs among single wells and multi-well groups because of the diverse fractured-vuggy configurati...Gas injection serves as a main enhanced oil recovery(EOR)method in fractured-vuggy carbonate reservoir,but its effect differs among single wells and multi-well groups because of the diverse fractured-vuggy configuration.Many researchers conducted experiments for the observation of fluid flow and the evaluation of production performance,while most of their physical models were fabricated based on the probability distribution of fractures and caves in the reservoir.In this study,a two-dimensional physical model of the karst fault system was designed and fabricated based on the geological model of TK748 well group in the seventh block of the Tahe Oilfield.The fluid flow and production performance of primary gas flooding were discussed.Gas-assisted gravity flooding was firstly introduced to take full use of gas-oil gravity difference,and its feasibility in the karst fault system was examined.Experimental results showed that primary gas flooding created more flow paths and achieved a remarkable increment of oil recovery compared to water flooding.Gas injection at a lower location was recommended to delay gas breakthrough.Gas-assisted gravity flooding achieved more stable gas-displacing-oil because oil production was at a lower location,and thus,the oil recovery was further enhanced.展开更多
Abstract： The impeller blade structure for gas injection refining under mechanical stirring has been explored by water model experiments. A sloped swept-back blade impeller is＇proposed for the purpose. The central p...Abstract： The impeller blade structure for gas injection refining under mechanical stirring has been explored by water model experiments. A sloped swept-back blade impeller is＇proposed for the purpose. The central part of the impeller is disk- or plate-shaped, and the blades are fitted to the side of the disk or plate. In addition, a disk is put on the top side of the impeller blades. The impeller can strengthen the radial and downward flow between the blades and weaken the swirl flow in the zone above the impeller. These effects on flow phenomena are favorable for disintegration and wide dispersion of bubbles which are injected from a nozzle attached to the center of the underside of the impeller. In addition, the sloped swept-back impeller requires less power consumption. The impeller shaft should be placed away from the vessel center so as to disperse the injected bubbles widely in the bath under mechanical stirring even with unidi- rectional impeller rotation and without installing baffles. The number of gas holes in the nozzle and the direction of gas injection have a little effect on the bubble disintegration and dispersion in the bath. Highly efficient gas injection refining can be established under the conditions of proper impeller size, larger nozzle immersion depth, larger eccen- tricity and rotation speed of the impeller. The sloped swept back blade impeller can decrease the power consumption and vet improve the bubble disintegration and wide dist^ersion in the bath.展开更多
The fabrication of AlN-TiC/Al composites by carbon- and nitrogen-containing gas injection into Al-Mg-Ti melts was studied. It was shown that AlN and TiC particles could be formed by the in situ reaction of mixture gas...The fabrication of AlN-TiC/Al composites by carbon- and nitrogen-containing gas injection into Al-Mg-Ti melts was studied. It was shown that AlN and TiC particles could be formed by the in situ reaction of mixture gas （N2 ＋ C2H2 ＋ NH3） with Al-Mg-Ti melts. The condition for the formation of AlN was that the treatment temperature must be higher than 1373 K, and the amounts of AlN and TiC increased with the increase of the treatment temperature and the gas injection time It was considered that AlN was formed by the direct reaction of Al with nitrogen-containing gas at the interface of the gas bubble and the melt. However, the mechanism of TiC formation is a combination mechanism of solution-precipitation and solid-liquid reaction.展开更多
Submerged gas injection into liquid leads to complex multiphase flow, in which nozzle geometries are crucial important for the operational expenditure in terms of pressure drop. The influence of the nozzle geometry on...Submerged gas injection into liquid leads to complex multiphase flow, in which nozzle geometries are crucial important for the operational expenditure in terms of pressure drop. The influence of the nozzle geometry on pressure drop between nozzle inlet and outlet has been experimentally studied for different gas flow rates and bath depths. Nozzles with circular, gear-like and four-leaf cross-sectional shape have been studied. The results indicate that, besides the hydraulic diameter of the outlet, the orifice area and the perimeter of the nozzle tip also play significant roles. For the same superficial gas velocity, the average pressure drop from the four-leaf-shaped geometry is the least. The influence of bath depth was found negligible. A correlation for the modified Euler number considering the pressure drop is proposed depending on nozzle geometric parameter and on the modified Froude number with the hydraulic diameter of the nozzle do as characteristic length.展开更多
A new approach is demonstrated in which soft experimentation can be performed for MMP measurements, thus replacing the common practice of slim tube displacement laboratory experiments. Recovery potential from oil rese...A new approach is demonstrated in which soft experimentation can be performed for MMP measurements, thus replacing the common practice of slim tube displacement laboratory experiments. Recovery potential from oil reservoirs by miscible flue gas injection was studied by slim tube and field-scale numerical simulation using two flue gases and seven crude oils sampled at different depths in three candidate reservoirs. The soft experimentations were conducted using Eclipse300<sup>TM</sup>, a three-phase compositional simulator. This study investigates minimum miscibility pressure (MMP), a significant miscible gas injection project screening tool. Successful design of the project is contingent to the accurate determination of the MMP. This study evaluates effects of important factors such as injection pressure, oil component composition, and injection gas composition on the MMP and recovery efficiency for slim tube and field-scale displacements. Two applicable MMP correlations were used for comparison and validation purposes.展开更多
A conceptual design review of the ITER gas injection system （GIS） function, safety, operation, and maintenance has recently been successfully completed. The GIS design can now continue to the preliminary design stag...A conceptual design review of the ITER gas injection system （GIS） function, safety, operation, and maintenance has recently been successfully completed. The GIS design can now continue to the preliminary design stage. This paper gives an overall description of the requirements and implementation at the concept design level. The designs of the sub-systems according to its breakdown structure are discussed against the corresponding requirements.展开更多
High-pressure gas injection has proved to be an effective disruption mitigation tech- nique in DIII-D tokamak experiments. If the method can be applied in future tokamak reactors not only for disruption mitigation but...High-pressure gas injection has proved to be an effective disruption mitigation tech- nique in DIII-D tokamak experiments. If the method can be applied in future tokamak reactors not only for disruption mitigation but also for plasma termination and fueling, it will have an attractive advantage over the pellet and liquid injection from the viewpoint of economy and engineering design. In order to investigate the feasibility of this option, a study has been carried out with relevant parameters for conveying tubes of different geometrical sizes and for different gases. These parameters include pressure drop, lagger time after the valve＇s opening, gas diffusion in an ultra-high vacuum condition, and particle number contour.展开更多
In this study,NIMROD simulations are performed to investigate the effects of massive helium gas injection level on the induced disruption on EAST tokamak.It is demonstrated in simulations that two different scenarios ...In this study,NIMROD simulations are performed to investigate the effects of massive helium gas injection level on the induced disruption on EAST tokamak.It is demonstrated in simulations that two different scenarios of plasma cooling(complete cooling and partial cooling)take place for different amounts of injected impurities.For the impurity injection above a critical level,a single MHD activity is able to induce a complete core temperature collapse.For impurity injection below the critical level,a series of multiple minor disruptions occur before the complete thermal quench.展开更多
Detailed information is provided for the design and construction of nitrogen drilling in a coal seam.Two prototype wells are considered.The Guo model is used to calculate the required minimum gas injection rate,while ...Detailed information is provided for the design and construction of nitrogen drilling in a coal seam.Two prototype wells are considered.The Guo model is used to calculate the required minimum gas injection rate,while the Finnie,Sommerfeld,and Tulsa models are exploited to estimate the ensuing erosion occurring in pipe strings.The calculated minimum gas injection rates are 67.4 m^(3)/min(with water)and 49.4 m^(3)/min(without water),and the actual field of use is 90–120 m^(3)/min.The difference between the calculated injection pressure and the field value is 6.5%–15.2%(formation with water)and 0.65%–7.32%(formation without water).The results show that the Guo model can more precisely represent the situation of the no water formation in the nitrogen drilling of a coal seam.The Finnie,Sommerfeld,and Tulsa models have different sensitivities to cutting densities,particle size,impact velocity and angle,and pipe string hardness.展开更多
Massive gas injection(MGI)is a traditional plasma disruption mitigation method.This method directly injected massive gas into the pre-disruption plasma and had been developed on the Experimental Advanced Superconducti...Massive gas injection(MGI)is a traditional plasma disruption mitigation method.This method directly injected massive gas into the pre-disruption plasma and had been developed on the Experimental Advanced Superconducting Tokamak(EAST).Different noble gas injection experiments,including He,Ne,and Ar,were performed to compare the mitigation effect of plasma disruption by evaluating the key parameters such as flight time,pre-thermal quench(pre-TQ),and current quench(CQ).The flight time was shorter for low atomic number(Z)gas,and the decrease in flight time by increasing the amount of gas was insignificant.However,both pre-TQ and CQ durations decreased considerably with the increase in gas injection amount.The effect of atomic mass on pre-TQ and CQ durations showed the opposite trend.The observed trend could help in controlling CQ duration in a reasonable area.Moreover,the analysis of radiation distribution with different impurity injections indicated that low Z impurity could reduce the asymmetry of radiation,which is valuable in mitigating plasma disruption.These results provided essential data support for plasma disruption mitigation on EAST and future fusion devices.展开更多
There is a need to increase ultimate recovery from petroleum reservoirs. In order to guarantee efficient resource extraction from reservoirs, primary recovery methods cannot be relied on throughout the life of a well....There is a need to increase ultimate recovery from petroleum reservoirs. In order to guarantee efficient resource extraction from reservoirs, primary recovery methods cannot be relied on throughout the life of a well. There is a time in the life of a reservoir when the primary energy will not be sufficient to ensure economic recovery. Complete abandonment of the reservoir at this point may not be a sound engineering decision given the huge investments in developing the asset. Secondary recovery methods present potentials for the recovery of the other trapped resources. The choice of the secondary recovery means depends on the reservoir and geologic conditions and should be determined by modeling and simulation. In this work, a simulation study is conducted for Niger Delta Field ABX2 to determine the performance of water-flooding and gas injection in the recovery of the asset after the primary recovery stage. ECLIPSE Blackoil simulator was used for the modeling and simulation. An equal reservoir rectangular grid block was designed for both the waterflooding and water injection comprising a total of 750 grid cells. Water and gas were injected in both cases at an injection rate of 11,000 stb/d and 300,000 scf/d for waterflooding and gas injection respectively. From the results of the simulation, it was realized that waterflooding gave a higher total oil recovery than gas injection. The difference in oil recovery from water-flooding and gas injection amounted to 0.08 MMstb/d. The Field Oil Recovery Efficiency (FOE) for waterflooding and gas injection was 38% and 16% respectively giving a difference of 22%. The waterflooding method was troubled with excessive water cuts due to water breakthroughs. Waterflooding was chosen against gas injection to be applied to Field ABX2 to improve recovery after primary production ceased.展开更多
It is of great importance to elucidate reduction swelling behaviors and reaction mechanism of oxidized pellet in hydrogen-enriched atmosphere under coke oven gas injection. In this work, the effects of hydrogen concen...It is of great importance to elucidate reduction swelling behaviors and reaction mechanism of oxidized pellet in hydrogen-enriched atmosphere under coke oven gas injection. In this work, the effects of hydrogen concentration in N_2-CO-H_2 atmosphere with unchanged CO content on reduction swelling behaviors of oxidized pellet at 1173 K were studied, to clarify the mechanism of hydrogen-enriched reduction and exclude the influences of CO. Then, the reduction swelling behaviors of oxidized pellet at 1173 K in actual atmosphere under coke oven gas(COG) injection, got from the simulation results of multi-fluid blast furnace model, were investigated. The results show that with the concentration of hydrogen increasing in N_2-CO-H_2 gas from 2% to 18%, the reduction swelling index of pellet decreases from 10.12% to 5.57% while the reduction ratio of pellet increases obviously from 39.85% to 69.58%. In addition, with COG injection rate increasing from 0 to 152.34 m^3/t, the reduction swelling index of pellet decreases slightly from 10.71% to 9.54% while the reduction ratio of pellet is increased from 31.57% to 36.39%. The microstructures of pellet are transformed from the platy structure to the flocculent structure.展开更多
technique.However,the main challenge in this process is the high minimum miscibility pressure(MMP)between natural gas and crude oil,which limits its application and recovery factor,especially in hightemperature reserv...technique.However,the main challenge in this process is the high minimum miscibility pressure(MMP)between natural gas and crude oil,which limits its application and recovery factor,especially in hightemperature reservoirs.Therefore,we present a novel investigation to quantify the effect of chemicalassisted MMP reduction on the oil recovery factor.Firstly,we measured the interfacial tension(IFT)of the methane-oil system in the presence of chemical or CO_(2) to calculate the MMP reduction at a constant temperature(373K)using the vanishing interfacial tension(VIT)method.Afterwards,we performed three coreflooding experiments to quantify the effect of MMP reduction on the oil recovery factor under different injection scenarios.The interfacial tension measurements show that adding a small fraction(1.5 wt%)of the tested surfactant(SOLOTERRA ME-6)achieved 9%of MMP reduction,while adding 20 wt%of CO_(2) to the methane yields 13%of MMP reduction.Then,the coreflooding results highlight the significance of achieving miscibility during gas injection,as the ultimate recovery factor increased from 65.5%under immiscible conditions to 77.2%using chemical-assisted methane,and to 79%using gas mixture after achieving near miscible condition.The results demonstrate the promising potential of the MMP reduction to signifi-cantly increase the oil recovery factor during gas injection.Furthermore,these results will likely expand the application envelop of the miscible gas injection,in addition to the environmental benefits of utilizing the produced gas by re-injection/recycling instead of flaring which contributes to reducing the greenhouse gas emissions.展开更多
文摘The BZ oilfield in the Bohai Sea is a rare,highly volatile reservoir with fractures in the metamorphic rocks of buried hills.Clarifying the mechanism of gas injection for improving oil recovery and determining the optimal way to deploy injection-production well networks are critical issues that must be urgently addressed for efficient oilfield development.Experimental research on the mixed-phase displacement mechanism through gas injection into indoor formation fluids was conducted to guide the efficient development of gas injection in oil fields.We established a model of dual-medium reservoir composition and researched the deployment strategy for a three-dimensional well network for gas injection development.The coupling relationship between key influencing factors of the well network and fracture development was also quantitatively analyzed.The results show that the solubility of the associated gas and strong volatile oil system injected into the BZ oilfield is high.This high solubility demonstrates a mixed-phase displacement mechanism involving intermediate hydrocarbons,dissolution and condensation of medium components,and coexistence of extraction processes.Injecting gas and crude oil can achieve a favorable mixing effect when the local formation pressure is greater than 35.79 MPa.Associated gas reinjection is recommended to supplement energy for developing the highly volatile oil reservoirs in the fractured buried hills of the BZ oilfield.This recommendation involves fully utilizing the structural position and gravity-assisted oil displacement mechanism to deploy an injection-production well network.Gas injection points should be constructed at the top of high areas,and oil production points should be placed at the middle and lower parts of low areas.This approach forms a spatial threedimensional well network.By adopting high inclination well development,the oil production well forms a 45°angle with the fracture direction,which increases the drainage area and enhances single-well production capacity.The optimal injection-production well spacing along the fracture direction is approximately 1000 m,while the reasonable well spacing in the vertical fracture direction is approximately 800 m.The research results were applied to the development practice of the buried hills in the BZ oilfield,which achieved favorable development results.These outcomes provide a valuable reference for the formulation of development plans and efficient gas injection development in similar oil and gas fields in buried hills.
文摘Optimal spacing for vertical wells can be effectively predicted with several published methods,but methods suitable for assessing the proper horizontal well spacing are rare.This work proposes a method for calculating the optimal horizontal well spacing for an ultra-low permeability reservoir e the Yongjin reservoir in the Juggar Basin,northwestern China.The result shows that a spacing of 640m is the most economical for the development of the reservoir.To better develop the reservoir,simulation approaches are used and a new model is built based on the calculated well spacing.Since the reservoir has an ultralow permeability,gas injection is regarded as the preferred enhanced oil recovery(EOR)method.Injection of different gases including carbon dioxide,methane,nitrogen and mixed gas are modelled.The results show that carbon dioxide injection is the most efficient and economical for the development of the reservoir.However,if the reservoir produces enough methane,reinjecting methane is even better than injecting carbon dioxide.
基金supported by the Sinopec Key Laboratory of Shale Oil and Gas Drilling,Completion and Fracturing(Grant No.35800000-22-ZC0613-0023)Beijing Municipal Natural Science Foundation(Grant No.2232073)the Sinopec Science and Technology Department(Grant Nos.P21078-8 and P22005).
文摘Low thermal evolution degree of gas and connected fracture network are key features in the continental shale gas reservoirs.When the pressure decreases lower than the dew point pressure,gas condensate diminishes the mobility of subsurface fluid forms in the near well region,which further reduces the productivity and final recovery factor in addition to the low connected fracture network.This work is motivated to investigate the application of gas injection,proven to be a feasible technique in conventional/marine-shale gas condensate reservoirs,in continental shale gas condensate reservoirs.We apply a compositional model to investigate the mechanism of gas injection treatment taking a continental shale gas condensate reservoir in the Fuxing area,Sichuan Basin,China as an example.The results demonstrate that for the removal of gas condensate during CO_(2)injection,re-vaporization plays the main mechanism through two processes including pressurization and development of miscibility,while the former is overwhelming.Considering the variation trend of the total volume of gas condensate,we divide the whole injection process into four and six stages in the single fracture model and fracture network model,respectively,and reason the trend with respect to phase behavior and flow pattern.A sensitive study on the injected gas type indicates that the sorting of the gas injection performance to remove gas condensate produced gas followed by CH_(4),and followed by CO_(2).Finally,we investigate the performance of cyclic produced-gas injection and optimize the injection scheme.This work provides technical and theoretical support for the development of continental shale gas reservoirs.
基金Projects (50974035,51074047) supported by the National Natural Science Foundation of ChinaProject (20090407) supported by the Doctoral Fund of Ministry of Education,ChinaProject (200921007) supported by Liaoning Key Science and Technology,China
文摘In gas injection refining processes,wide dispersion of small bubbles in the bath is indispensable for high refining efficiency.Eccentric mechanical stirring with unidirectional impeller rotation was tested using a water model for pursuing better bubble disintegration and dispersion.Effects of various factors on bubble disintegration and dispersion were investigated.These factors were stirring mode,eccentricity and rotation speed,nozzle structure,nozzle immersion depth,and gas flow rate.Gas injection from a nozzle at the end of the impeller shaft and from an immersed lance was studied.Under eccentric stirring,a vortex was formed away from the shaft.Small bubbles were produced in the strong turbulence or high shear stress field near the rotating impeller and moved in the direction to the vortex keeping up with the macroscopic flow induced by the mechanical stirring.Thus small bubbles could disperse widely in the bath under eccentric stirring with unidirectional rotation.
基金Project(51371104)supported by the National Natural Science Foundation of China
文摘Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical microscopy,scanning electron microscopy（SEM） and Auger electron spectroscopy（AES） were used to analyze the influence of oxygen content on cell structure,relative density,macro and micro morphology of cell walls,coverage area fraction of oxide film,thickness of oxide film and other aspects.Results indicate that the coverage area fraction of oxide film on bubble surface increases with the increase of oxygen content when the oxygen volume is less than 1.2%.While when the oxygen volume fraction is larger than 1.6%,an oxide film covers the entire bubble surface and aluminum foams with good cell structure can be produced.The thicknesses of oxide films of aluminum foams produced by gas mixtures containing 1.6%-21%oxygen are almost the same.The reasons why the thickness of oxide film nearly does not change with the variation of oxygen content and the amount of oxygen needed to achieve 100%coverage of oxide film are both discussed.In addition,the role of oxide film on bubble surface in foam stability is also analyzed.
基金Project(51371104)supported by the National Nature Science Foundation of China
文摘In the range of 620？710 °C, air was blown into A356 aluminum alloy melt to produce aluminum foams. In order to study the influence of temperature on the thickness of oxide film on bubble surface, Auger electron spectroscopy （AES） was used. Based on the knowledge of corrosion science and hydrodynamics, two oxidation kinetics models of oxide film on bubble surface were established. The thicknesses of oxide films produced at different temperatures were predicted through those two models. Furthermore, the theoretical values were compared with the experimental values. The results indicate that in the range of 620？710 °C, the theoretical values of the thickness of oxide film predicted by the model including the rising process are higher than the experimental values. While, the theoretical values predicted by the model without the rising process are in good agreement with the experimental values, which shows this model objectively describes the oxidation process of oxide film on bubble surface. This work suggests that the oxidation kinetics of oxide film on bubble surface of aluminum foams produced by gas injection foaming process follows the Arrhenius equation.
基金Item Sponsored by National Natural Science Foundation of China and Baosteel Co(50674020)
文摘The flow field of molten steel and the interfacial behaviour between molten steel and liquid slag layer in medium-thin slab continuous casting mold with argon gas injection were studied by numerical simulation, in which the effects of nozzle submergence depth and port angle, casting speed, and argon gas flow rate on the flow and the level fluctuation of molten steel were considered. The results show that the molten steel is jetted from the submerged en- try nozzle （SEN） with three ports into the mold and forms three recirculation zones including one upper recireulation zone and two lower recirculation zones. Argon gas injection results in a secondary vortex flow in the upper zone near the nozzle. For a given casting speed and argon gas flow rate, increasing the side port angle and submergence depth of nozzle can effectively restrain the steel/slag interracial fluctuation. Increasing the casting speed would prick up the level fluctuation. For a fixed casting speed, argon gas flow rate has a critical value, the interracial fluctuation with argon gas injection are stronger than the case without argon gas injection when the argon gas flow rate is less than the critical value, but when the argon gas flow rate exceeds the critical value, the level fluctuation is calmer than that without argon gas injection.
基金the financial support from National Natural Science Foundation of China(51504268)National Technology Major Project of China(2016ZX05014).
文摘Gas injection serves as a main enhanced oil recovery(EOR)method in fractured-vuggy carbonate reservoir,but its effect differs among single wells and multi-well groups because of the diverse fractured-vuggy configuration.Many researchers conducted experiments for the observation of fluid flow and the evaluation of production performance,while most of their physical models were fabricated based on the probability distribution of fractures and caves in the reservoir.In this study,a two-dimensional physical model of the karst fault system was designed and fabricated based on the geological model of TK748 well group in the seventh block of the Tahe Oilfield.The fluid flow and production performance of primary gas flooding were discussed.Gas-assisted gravity flooding was firstly introduced to take full use of gas-oil gravity difference,and its feasibility in the karst fault system was examined.Experimental results showed that primary gas flooding created more flow paths and achieved a remarkable increment of oil recovery compared to water flooding.Gas injection at a lower location was recommended to delay gas breakthrough.Gas-assisted gravity flooding achieved more stable gas-displacing-oil because oil production was at a lower location,and thus,the oil recovery was further enhanced.
基金Item Sponsored by National Natural Science Foundation of China(50974035,51074047)National High Technology Research and Development Program(863 Program)of China(2010AA03A405,2012AA062303)Innovation Team Project of Provincial Science and Technology of Liaoning Province of China(LT2010034)
文摘Abstract： The impeller blade structure for gas injection refining under mechanical stirring has been explored by water model experiments. A sloped swept-back blade impeller is＇proposed for the purpose. The central part of the impeller is disk- or plate-shaped, and the blades are fitted to the side of the disk or plate. In addition, a disk is put on the top side of the impeller blades. The impeller can strengthen the radial and downward flow between the blades and weaken the swirl flow in the zone above the impeller. These effects on flow phenomena are favorable for disintegration and wide dispersion of bubbles which are injected from a nozzle attached to the center of the underside of the impeller. In addition, the sloped swept-back impeller requires less power consumption. The impeller shaft should be placed away from the vessel center so as to disperse the injected bubbles widely in the bath under mechanical stirring even with unidi- rectional impeller rotation and without installing baffles. The number of gas holes in the nozzle and the direction of gas injection have a little effect on the bubble disintegration and dispersion in the bath. Highly efficient gas injection refining can be established under the conditions of proper impeller size, larger nozzle immersion depth, larger eccen- tricity and rotation speed of the impeller. The sloped swept back blade impeller can decrease the power consumption and vet improve the bubble disintegration and wide dist^ersion in the bath.
文摘The fabrication of AlN-TiC/Al composites by carbon- and nitrogen-containing gas injection into Al-Mg-Ti melts was studied. It was shown that AlN and TiC particles could be formed by the in situ reaction of mixture gas （N2 ＋ C2H2 ＋ NH3） with Al-Mg-Ti melts. The condition for the formation of AlN was that the treatment temperature must be higher than 1373 K, and the amounts of AlN and TiC increased with the increase of the treatment temperature and the gas injection time It was considered that AlN was formed by the direct reaction of Al with nitrogen-containing gas at the interface of the gas bubble and the melt. However, the mechanism of TiC formation is a combination mechanism of solution-precipitation and solid-liquid reaction.
基金Project(51676211) supported by the National Natural Science Foundation of ChinaProject(2017SK2253) supported by the Key R&D Plan of Hunan Province of China+1 种基金Project(2015zzts044) supported by Fundamental Research Funds for the Central Universities,ChinaProject(201606370092) supported by the China Scholarship Council
文摘Submerged gas injection into liquid leads to complex multiphase flow, in which nozzle geometries are crucial important for the operational expenditure in terms of pressure drop. The influence of the nozzle geometry on pressure drop between nozzle inlet and outlet has been experimentally studied for different gas flow rates and bath depths. Nozzles with circular, gear-like and four-leaf cross-sectional shape have been studied. The results indicate that, besides the hydraulic diameter of the outlet, the orifice area and the perimeter of the nozzle tip also play significant roles. For the same superficial gas velocity, the average pressure drop from the four-leaf-shaped geometry is the least. The influence of bath depth was found negligible. A correlation for the modified Euler number considering the pressure drop is proposed depending on nozzle geometric parameter and on the modified Froude number with the hydraulic diameter of the nozzle do as characteristic length.
文摘A new approach is demonstrated in which soft experimentation can be performed for MMP measurements, thus replacing the common practice of slim tube displacement laboratory experiments. Recovery potential from oil reservoirs by miscible flue gas injection was studied by slim tube and field-scale numerical simulation using two flue gases and seven crude oils sampled at different depths in three candidate reservoirs. The soft experimentations were conducted using Eclipse300<sup>TM</sup>, a three-phase compositional simulator. This study investigates minimum miscibility pressure (MMP), a significant miscible gas injection project screening tool. Successful design of the project is contingent to the accurate determination of the MMP. This study evaluates effects of important factors such as injection pressure, oil component composition, and injection gas composition on the MMP and recovery efficiency for slim tube and field-scale displacements. Two applicable MMP correlations were used for comparison and validation purposes.
基金undertaken within the framework of the ITER Projectsupported by the ITER Organization and/or its Members,i.e.,China,EU,India,Japan,Korea,Russia
文摘A conceptual design review of the ITER gas injection system （GIS） function, safety, operation, and maintenance has recently been successfully completed. The GIS design can now continue to the preliminary design stage. This paper gives an overall description of the requirements and implementation at the concept design level. The designs of the sub-systems according to its breakdown structure are discussed against the corresponding requirements.
基金The project supported by the Nuclear Researchers Exchange Program of Japan Society for the Promotion of Science
文摘High-pressure gas injection has proved to be an effective disruption mitigation tech- nique in DIII-D tokamak experiments. If the method can be applied in future tokamak reactors not only for disruption mitigation but also for plasma termination and fueling, it will have an attractive advantage over the pellet and liquid injection from the viewpoint of economy and engineering design. In order to investigate the feasibility of this option, a study has been carried out with relevant parameters for conveying tubes of different geometrical sizes and for different gases. These parameters include pressure drop, lagger time after the valve＇s opening, gas diffusion in an ultra-high vacuum condition, and particle number contour.
基金supported by the National Magnetic Confinement Fusion Science Program of China(No.2019YFE03050004)National Natural Science Foundation of China(Nos.11775221 and 51821005)+1 种基金US DOE(Nos.DEFG02-86ER53218 and DESC0018001)the Fundamental Research Funds for the Central Universities at Huazhong University of Science and Technology(No.2019kfyXJJS193).
文摘In this study,NIMROD simulations are performed to investigate the effects of massive helium gas injection level on the induced disruption on EAST tokamak.It is demonstrated in simulations that two different scenarios of plasma cooling(complete cooling and partial cooling)take place for different amounts of injected impurities.For the impurity injection above a critical level,a single MHD activity is able to induce a complete core temperature collapse.For impurity injection below the critical level,a series of multiple minor disruptions occur before the complete thermal quench.
基金National Science and Technology Major Special Project,2016ZX05044CBM Development Technology and Pilot Test in East Yunnan and Western Guizhou.
文摘Detailed information is provided for the design and construction of nitrogen drilling in a coal seam.Two prototype wells are considered.The Guo model is used to calculate the required minimum gas injection rate,while the Finnie,Sommerfeld,and Tulsa models are exploited to estimate the ensuing erosion occurring in pipe strings.The calculated minimum gas injection rates are 67.4 m^(3)/min(with water)and 49.4 m^(3)/min(without water),and the actual field of use is 90–120 m^(3)/min.The difference between the calculated injection pressure and the field value is 6.5%–15.2%(formation with water)and 0.65%–7.32%(formation without water).The results show that the Guo model can more precisely represent the situation of the no water formation in the nitrogen drilling of a coal seam.The Finnie,Sommerfeld,and Tulsa models have different sensitivities to cutting densities,particle size,impact velocity and angle,and pipe string hardness.
基金Project supported by the National Key Research and Development Program of China(Grant Nos.2017YFE0301100 and 2022YFE03130000)the National Natural Science Foundation of China(Grant Nos.12105322,11905138,11905148,and 11905254)+5 种基金the Natural Science Foundation of Anhui Province of China(Grant No.2108085QA38)the Chinese Postdoctoral Science Found(Grant No.2021000278)the Presidential Foundation of Hefei Institutes of Physical Science(Grant No.YZJJ2021QN12)the U.S.Department of Energy contract DE-AC02–09CH11466(Grant No.DE-SC0016553)the Users with Excellence Program of Hefei Science Center CAS(Grant Nos.2020HSC-UE010 and 2021HSC-UE013)Interdisciplinary and Collaborative Teams of CAS.
文摘Massive gas injection(MGI)is a traditional plasma disruption mitigation method.This method directly injected massive gas into the pre-disruption plasma and had been developed on the Experimental Advanced Superconducting Tokamak(EAST).Different noble gas injection experiments,including He,Ne,and Ar,were performed to compare the mitigation effect of plasma disruption by evaluating the key parameters such as flight time,pre-thermal quench(pre-TQ),and current quench(CQ).The flight time was shorter for low atomic number(Z)gas,and the decrease in flight time by increasing the amount of gas was insignificant.However,both pre-TQ and CQ durations decreased considerably with the increase in gas injection amount.The effect of atomic mass on pre-TQ and CQ durations showed the opposite trend.The observed trend could help in controlling CQ duration in a reasonable area.Moreover,the analysis of radiation distribution with different impurity injections indicated that low Z impurity could reduce the asymmetry of radiation,which is valuable in mitigating plasma disruption.These results provided essential data support for plasma disruption mitigation on EAST and future fusion devices.
文摘There is a need to increase ultimate recovery from petroleum reservoirs. In order to guarantee efficient resource extraction from reservoirs, primary recovery methods cannot be relied on throughout the life of a well. There is a time in the life of a reservoir when the primary energy will not be sufficient to ensure economic recovery. Complete abandonment of the reservoir at this point may not be a sound engineering decision given the huge investments in developing the asset. Secondary recovery methods present potentials for the recovery of the other trapped resources. The choice of the secondary recovery means depends on the reservoir and geologic conditions and should be determined by modeling and simulation. In this work, a simulation study is conducted for Niger Delta Field ABX2 to determine the performance of water-flooding and gas injection in the recovery of the asset after the primary recovery stage. ECLIPSE Blackoil simulator was used for the modeling and simulation. An equal reservoir rectangular grid block was designed for both the waterflooding and water injection comprising a total of 750 grid cells. Water and gas were injected in both cases at an injection rate of 11,000 stb/d and 300,000 scf/d for waterflooding and gas injection respectively. From the results of the simulation, it was realized that waterflooding gave a higher total oil recovery than gas injection. The difference in oil recovery from water-flooding and gas injection amounted to 0.08 MMstb/d. The Field Oil Recovery Efficiency (FOE) for waterflooding and gas injection was 38% and 16% respectively giving a difference of 22%. The waterflooding method was troubled with excessive water cuts due to water breakthroughs. Waterflooding was chosen against gas injection to be applied to Field ABX2 to improve recovery after primary production ceased.
基金Project(51404005)supported by the National Natural Science Foundation of China
文摘It is of great importance to elucidate reduction swelling behaviors and reaction mechanism of oxidized pellet in hydrogen-enriched atmosphere under coke oven gas injection. In this work, the effects of hydrogen concentration in N_2-CO-H_2 atmosphere with unchanged CO content on reduction swelling behaviors of oxidized pellet at 1173 K were studied, to clarify the mechanism of hydrogen-enriched reduction and exclude the influences of CO. Then, the reduction swelling behaviors of oxidized pellet at 1173 K in actual atmosphere under coke oven gas(COG) injection, got from the simulation results of multi-fluid blast furnace model, were investigated. The results show that with the concentration of hydrogen increasing in N_2-CO-H_2 gas from 2% to 18%, the reduction swelling index of pellet decreases from 10.12% to 5.57% while the reduction ratio of pellet increases obviously from 39.85% to 69.58%. In addition, with COG injection rate increasing from 0 to 152.34 m^3/t, the reduction swelling index of pellet decreases slightly from 10.71% to 9.54% while the reduction ratio of pellet is increased from 31.57% to 36.39%. The microstructures of pellet are transformed from the platy structure to the flocculent structure.
基金supported by a joint project with Southwest Petroleum University (China)funded by Tarim Oilfield Company (PetroChina).
文摘technique.However,the main challenge in this process is the high minimum miscibility pressure(MMP)between natural gas and crude oil,which limits its application and recovery factor,especially in hightemperature reservoirs.Therefore,we present a novel investigation to quantify the effect of chemicalassisted MMP reduction on the oil recovery factor.Firstly,we measured the interfacial tension(IFT)of the methane-oil system in the presence of chemical or CO_(2) to calculate the MMP reduction at a constant temperature(373K)using the vanishing interfacial tension(VIT)method.Afterwards,we performed three coreflooding experiments to quantify the effect of MMP reduction on the oil recovery factor under different injection scenarios.The interfacial tension measurements show that adding a small fraction(1.5 wt%)of the tested surfactant(SOLOTERRA ME-6)achieved 9%of MMP reduction,while adding 20 wt%of CO_(2) to the methane yields 13%of MMP reduction.Then,the coreflooding results highlight the significance of achieving miscibility during gas injection,as the ultimate recovery factor increased from 65.5%under immiscible conditions to 77.2%using chemical-assisted methane,and to 79%using gas mixture after achieving near miscible condition.The results demonstrate the promising potential of the MMP reduction to signifi-cantly increase the oil recovery factor during gas injection.Furthermore,these results will likely expand the application envelop of the miscible gas injection,in addition to the environmental benefits of utilizing the produced gas by re-injection/recycling instead of flaring which contributes to reducing the greenhouse gas emissions.
