To address the issue of extensive deformation in the Tabaiyi Tunnel caused by the fault zone,nuclear magnetic resonance(NMR)technology was employed to analyze the physical and mechanical properties of waterabsorbing m...To address the issue of extensive deformation in the Tabaiyi Tunnel caused by the fault zone,nuclear magnetic resonance(NMR)technology was employed to analyze the physical and mechanical properties of waterabsorbing mudstone.This analysis aimed to understand the mechanism behind the significant deformations.Drawing from the principle of excavation stress compensation,a support scheme featuring NPR anchorcables and an asymmetric truss support system was devised.To validate the scheme,numerical analysis using a combination of the Discrete Element Method(DEM)-Finite Element Method(FEM)was conducted.Additionally,similar material model tests and engineering measurements were carried out.Field experiments were also performed to evaluate the NPR anchor-cable and truss support system,focusing on anchor cable forces,pressures between the truss and surrounding rock,pressures between the initial support and secondary lining,as well as the magnitude of settlement and convergence deformation in the surrounding rock.The results indicate that the waterinduced expansion of clay minerals,resulting from damage caused by fissure water,accelerated the softening of the mudstone's internal structure,leading to significant deformations in the Tabaiyi Tunnel under high tectonic stress.The original support design fell short as the length of the anchor rods was smaller than the expansion depth of the plastic zone.As a result,the initial support structure bore the entire load from the surrounding rock,and a non-coupled deformation contact was observed between the double-arch truss and the surrounding rock.The adoption of NPR asymmetric anchor-cable support effectively restrained the expansion and asymmetric distribution characteristics of the plastic zone.Considering the mechanical degradation caused by water absorption in mudstone,the rigid constraint provided by the truss proved crucial for controlling the stability of the surrounding rock.These research findings hold significant implications for managing large deformations in soft rock tunnels situated within fractured zones under high tectonic stress conditions.展开更多
Grouting is a widely used approach to reinforce broken surrounding rock mass during the construction of underground tunnels in fault fracture zones,and its reinforcement effectiveness is highly affected by geostress.I...Grouting is a widely used approach to reinforce broken surrounding rock mass during the construction of underground tunnels in fault fracture zones,and its reinforcement effectiveness is highly affected by geostress.In this study,a numerical manifold method(NMM)based simulator has been developed to examine the impact of geostress conditions on grouting reinforcement during tunnel excavation.To develop this simulator,a detection technique for identifying slurry migration channels and an improved fluid-solid coupling(FeS)framework,which considers the influence of fracture properties and geostress states,is developed and incorporated into a zero-thickness cohesive element(ZE)based NMM(Co-NMM)for simulating tunnel excavation.Additionally,to simulate coagulation of injected slurry,a bonding repair algorithm is further proposed based on the ZE model.To verify the accuracy of the proposed simulator,a series of simulations about slurry migration in single fractures and fracture networks are numerically reproduced,and the results align well with analytical and laboratory test results.Furthermore,these numerical results show that neglecting the influence of geostress condition can lead to a serious over-estimation of slurry migration range and reinforcement effectiveness.After validations,a series of simulations about tunnel grouting reinforcement and tunnel excavation in fault fracture zones with varying fracture densities under different geostress conditions are conducted.Based on these simula-tions,the influence of geostress conditions and the optimization of grouting schemes are discussed.展开更多
The Wenchuan earthquake triggered cascading disasters of landslides and debris flows that caused severe vegetation damage. Fracture zones can affect geodynamics and spatial pattern of vegetation damage. A segment trac...The Wenchuan earthquake triggered cascading disasters of landslides and debris flows that caused severe vegetation damage. Fracture zones can affect geodynamics and spatial pattern of vegetation damage. A segment tracing algorithm method was applied for identifying the regional fracture system through lineament extractions from a shaded digital elevation model with 25 m mesh for southern Wenchuan. Remote sensing and geographic information system techniques were used to analyze the spatiotemporal vegetation pattern. The relationship between vegetation type identified from satellite images and lineament density was used to characterize the distribution patterns of each vegetation type according to fracture zones. Broad-leaved forest, mixed forest, and farmland persist in areas with moderate lineament density. Deciduous broad-leaved and coniferous forest persists in less frac- tured areas. Shrub and meadow seem to be relatively evenly distributed across all lineament densities.Meadow, farmland, and shrub persist in the fractured areas. Changes of spatial structure and correlation between vegetation patterns before and after the earthquake were examined using semivariogram analysis of normalized difference vegetation indices derived from Landsat enhanced thematic mapper images. The sill values of the semivariograms show that the spatial heterogeneity of vegetation covers increased after the earthquake. Moreover, the anisotropic behaviors of the semivariograms coincide with the vegetation changes due to the strikes of fracture zones.展开更多
To study the heights of the caved zone and water-conducting fracture zone in backfill mining,the failure mechanism of strata during backfill mining was analyzed,and a method for determining the heights of the two zone...To study the heights of the caved zone and water-conducting fracture zone in backfill mining,the failure mechanism of strata during backfill mining was analyzed,and a method for determining the heights of the two zones was proposed based on key strata theory.The movement and failure regularity of the strata above the backfilling panel were revealed through numerical simulation.Considering the geologic conditions of the CT101 backfilling panel,the height of the fracture zone was determined using the proposed method along with empirical calculation,numerical simulation,and borehole detection.The results of the new calculation method were similar to in situ measurements.The traditional empirical formula,which is based on the equivalent mining height model,resulted in large errors during calculation.The findings indicate the reliability of the new method and demonstrate its significance for creating reference data for related studies.展开更多
Prediction of the height of a water-flowing fracture zone(WFFZ)is the foundation for evaluating water bursting conditions on roof coal.By taking the Binchang mining area as the study area and conducting an in-depth st...Prediction of the height of a water-flowing fracture zone(WFFZ)is the foundation for evaluating water bursting conditions on roof coal.By taking the Binchang mining area as the study area and conducting an in-depth study of the influence of coal seam thickness,burial depth,working face length,and roof category on the height of a WFFZ,we proposed that the proportion of hard rock in different roof ranges should be used to characterise the influence of roof category on WFFZ height.Based on data of WFFZ height and its influence index obtained from field observations,a prediction model is established for WFFZ height using a combination of a genetic algorithm and a support-vector machine.The reliability and superiority of the prediction model were verified by a comparative study and an engineering application.The results show that the main factors affecting WFFZ height in the study area are coal seam thickness,burial depth,working face length,and roof category.Compared with multiple-linear-regression and back-propagation neural-network approaches,the height-prediction model of the WFFZ based on a genetic-algorithm support-vector-machine method has higher training and prediction accuracy and is more suitable for WFFZ prediction in the mining area.展开更多
In Xikuangshan antimony ore-field, the western fracture zone is a composite of major fault, F75, and its secondary faults, such as F71, F72 and F3 etc.. On plane, the fracture zone scatters from southwest to northeast...In Xikuangshan antimony ore-field, the western fracture zone is a composite of major fault, F75, and its secondary faults, such as F71, F72 and F3 etc.. On plane, the fracture zone scatters from southwest to northeast, and concentrates from upper to deeper level on profile. All ore-bodies exist in the carbonate of footwall of the major fault or that of the footwall of its secondary faults. From 480 m and 320 m to 120 m level, the fractal dimensional number of the fault system decreases from 1.482 2 and 1.448 6 to 1.339 2, which indicates the form of fracture zone becoming more simple at deeper level. And in five sub-ranges, the III and IV sub-ranges are the known area, and the I, II and V sub-ranges are unknown. The fractal studies of the western fracture zone in these sub-ranges show that the fractal dimensional numbers of the I and II, being 1.201 5 and 1.278 0, respectively, are smaller than that of the III and IV, being 1.475 9 and 1.576 9, respectively; and that of the V, being 1.571 2, keeps with that of the III, IV sub-ranges. So mineralization is not well in I and II sub-ranges, and V sub-range is the best to benefit mineralization.展开更多
Planktic foraminifera from the calcareous substrate of a ferromanganese crust in the Vityaz Fracture Zone （VFZ）, Central Indian Ridge were studied to reconstruct the early Pliocene paleoceanography of this region. E...Planktic foraminifera from the calcareous substrate of a ferromanganese crust in the Vityaz Fracture Zone （VFZ）, Central Indian Ridge were studied to reconstruct the early Pliocene paleoceanography of this region. Eleven species of planktic foraminifera were encountered, among them Globorotalia menardii, Neogloboquadrina dutertrei, Globigerina bulloides and Globigerinoides tuber are prominent. Predominance of N. dutertrei in the top 3 cm of the carbonate substrate is attributed to an influx of fresh water which eventually triggered their productivity by increasing the nutrient level. The presence of G. bulloides and G. menardii in significant proportions in deeper layers suggests the prevalence of open ocean upwelling. The bulk chemical compositions of the substrate at different depth intervals indicates higher enrichment of trace metals in the upper sections which could have been supplied through oceanic water by the chemical weathering of terrestrial matter during the peak of Pliocene Asian monsoon. Thus, it is concluded that during the early Pliocene the biogenic components of the substrate were distinctly contributed by both upwelling and productivity triggered by an influx of fresh water originating from the intensification of the Asian monsoon during the early Pliocene Period.展开更多
It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power...It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power Spectral Density） function is developed using wave propagation theory, while for vertical incidence of waves the cross-PSD function is composed by auto-PSD model, coherence model and site response model. As the seismic input, the eross-PSD function is used to calculate the the axial and lateral seismic responses of underground pipeline through the fracture zone. The results show that the incident directions of seismic waves, width and soil property of the fracture zone have great influence on underground pipeline. It is suggested that the flexible joints with appropriate stiffness should be added into the pipeline near the interfaces between the fracture zone and the surrounded media.展开更多
Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided in...Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided into three zones, including elastic zone, plastic damage zone and shear fracture zone for assessing the stability of the tunnel surrounding rock. By local hydrogeology, the stresses of surrounding rock of Jinshazhou circular tunnel was analyzed and the stress solutions on the elastic and plastic damage zones were obtained by applying the theories of fluid-solid coupling and elasto-plastic damage mechanics. The shear fracture zone generated by joints was studied and its range was determined by using Molar-Coulomb strength criterion. Finally, the correctness of the theoretical results was validated by comparing the scopes of shear fracture zones calculated in this paper with those from literature.展开更多
The mylonites occurred in the fracture zones are studied by dynamically recrystallized quartz grains.The natural microstructures in mylonites are simulated and the deformation conditions of mylonitization are estimate...The mylonites occurred in the fracture zones are studied by dynamically recrystallized quartz grains.The natural microstructures in mylonites are simulated and the deformation conditions of mylonitization are estimated by fractal analysis,recrystallized grain size paleopiezometer and flow laws of quartzite.Depending on fractal analysis,the deformation temperature of mylonitization is approximately 600℃,which presents high greenschist facies to low amphibolite facies.The mylonitization occurred at differential stresses of 9.1--10.7MPa(lower limits).Compared with extrapolation of quartzite flow laws and estimates of fractal analysis,the strain rate of mylonitization is under 10-13.8/s.展开更多
We have imaged rock density distribution beneath Liwa fracture zone in the southern part of the the Sumatran Fault Zone by modelling and inverting Bouguer gravity data in two-and three-dimensional environments, respec...We have imaged rock density distribution beneath Liwa fracture zone in the southern part of the the Sumatran Fault Zone by modelling and inverting Bouguer gravity data in two-and three-dimensional environments, respectively. The purpose of this study is aimed to figure out the subsurface distribution of rock densities associated with subsurface basement structure representing the evidence of trans-tensional tectonic product in the SF. In the gravity modeling, to eliminate distortions to the measured gravity values before modelling and inverting the data, Bouguer anomalies obtained in field measurements are reduced to the horizontal plane of z = +800 m as a representation of the average elevation in Liwa. For the inversion, we used algorithm implementing depth-and minimum volume weighting parameters in order to obtain a smooth model with better vertical resolution. The two-dimensional models show clearly surface topography of the basement rocks and the presence of normal faults. The reduced Bouguer anomaly of +800 m elevation shows the presence of structural lineaments extending primarily in a northwest-southeast direction, parallel to Sumatran Fault Zone and older graben faults showing a negative flower structure. From the three-dimensional inversion, the model illustrates an increase of density contrast, lower values being found near the surface and higher values in the deeper parts. The lower density contrast of 0.15 to 0.3 g/cm<sup>3</sup> found in the rock groups at depths of 2 km and less is characteristic of relatively homogeneous and poorly compacted rocks. Rocks with moderate to high density contrast (>1.0 g/cm<sup>3</sup>) are recognized at depths of over 2 km. This model suggests a change of basement morphology as a function of depth, and delineates structural lineaments extending in northwest-southeast direction. This study supports the previous thought that Liwa area is underlain by graben structures, formed by trans-tensional tectonic events. Higher-density Tertiary volcanic breccia and lower-density Quaternary volcanic products of the Ranau Formation form the basement rocks and the overlying younger sediments, respectively.展开更多
Understanding the anisotropic fracture behavior and the characteristics of the fracture process zone(FPZ)under size effects in laminated rocks,as well as its role in rock fracturing,is crucial for various engineering ...Understanding the anisotropic fracture behavior and the characteristics of the fracture process zone(FPZ)under size effects in laminated rocks,as well as its role in rock fracturing,is crucial for various engineering applications.In this study,three-point bending tests were conducted on shale specimens with varying bedding angles and sizes.The anisotropic characteristics and size effects of fracture parameters were revealed.A comparative analysis was performed on the evolutions of FPZs computed using size effect theory,digital image correlation(DIC),and linear elastic fracture mechanics.The results divulged that:(i)With increasing bedding angles,there is a noticeable decrease in apparent fracture toughness(KICA),apparent fracture energy(GICA),and nominal strength(σ_(Nu)).When the bedding angle of shale is less than 45°,the crack propagation and fracture parameters are mainly influenced by the matrix.Contrary,shale with bedding angles greater than 60°,the crack propagation and fracture parameters are mainly controlled by the bedding.When the bedding angle is between 45°and 60°,the fracture propagation evolves from permeating the matrix to extending along the bedding;(ii)The fracture parameters exhibit significant size dependent behavior,as KICA and GICA rise with increasing specimen size,butσNu falls with increasing specimen sizes.The fracture parameters align with the theoretical predictions of Bažant size effect law;and(iii)The lengths of DIC-based FPZ,effective FPZ,and inelastic zone follow W-shape variations with bedding angle.The dimensionless sizes of FPZ and inelastic zone decrease with specimen size,indicating a size effect.Furthermore,there is a negative relation between KICA and the dimensionless size of the FPZ,whileσNu is positively correlated to the dimensionless size of the FPZ.This highlights the essential role of the FPZ in the size effect of rock fracture.The bedding angle exerts an influence on the FPZ,subsequently affecting the anisotropic fracture and size-dependent behavior of shale.展开更多
During drilling operations in deep fractured tight gas reservoirs,lost circulation of working fluid frequently occurs due to the formationʼs low pressure-bearing capacity.Adding lost circulation materials(LCMs)to dril...During drilling operations in deep fractured tight gas reservoirs,lost circulation of working fluid frequently occurs due to the formationʼs low pressure-bearing capacity.Adding lost circulation materials(LCMs)to drilling fluids is the most common method for controlling lost circulation.Among these,granular LCMs are widely used,but the application frequency of flaky LCMs has been increasing annually due to their unique morphology.However,the migration and plugging behavior of flaky LCMs within fractures,and the mechanisms enhancing the pressure-bearing capacity of the plugging zone are not well understood.Therefore,this study conducted visual plugging experiments and dynamic fracture plugging experiments to evaluate the plugging mode and pressure-bearing capacity of the plugging slurry with various particle sizes and concentrations of flaky LCMs.The experimental results demonstrate that the fracture plugging process can be divided into four stages:uniform flow stage of the plugging slurry,formation and development stage of the bridging area,formation and development stage of the plugging area,and pressure-bearing stage of the plugging zone.The inclusion of flaky LCMs notably reduces the duration of stages 1 and 2,while simultaneously increasing the proportion of the plugging zone and enhancing its surface porosity.Flaky LCMs reduce the effective fracture width through“interception”and“co-bridging”modes,thus improving plugging zone formation efficiency.Appropriate particle size and concentration of flaky LCMs increase the area and length of the plugging zone.This reduces the fracture width increment caused by injection pressure and enhances frictional force between the plugging zone and fracture surface,thereby improving the pressure-bearing capacity of the plugging zone.However,excessively high concentrations of flaky LCMs result in decreased structural stability of the plugging zone,and excessively large particle sizes increase the risk of plugging outside fracture inlet.The recommended concentration of flaky LCMs in the plugging slurry is 2%–3%,with a particle size 1.2 to 1.5 times that of the bridging granular LCMs and not exceeding twice the fracture width.This study provides a theoretical foundation for selecting LCMs and designing plugging formulations for field applications.展开更多
This study investigates the fracture characteristics and the fracture process zone(FPZ)of mode I fracture in sandstone,aiming to analyze the propagation behaviors of mode I crack under different freeze-thaw cycles.Sem...This study investigates the fracture characteristics and the fracture process zone(FPZ)of mode I fracture in sandstone,aiming to analyze the propagation behaviors of mode I crack under different freeze-thaw cycles.Semicircular bending tests(SCB)were conducted using different freeze-thaw cycles to evaluate mode I fracture toughness,FPZ dynamics,and macroscopic microscopic features.Digital image correlation(DIC)and scanning electron microscopy(SEM)techniques were employed for detailed analysis.Experimental results reveal that freeze-thaw cycling leads to the widening of both preexisting and newly formed microcracks between internal particles.Under external loading,crack propagation deviates from prefabricated paths,forming serrated crack patterns.The FPZ initiates at the prefabricated crack tip and extends toward the loading end,exhibiting an arcshaped tip shape.The FPZ length increases with loading but decreases after reaching a peak value.With additional freeze-thaw cycles,the maximum FPZ length first increases and then diminishes.展开更多
As one of the typical deposits in the Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province,the Daliangzi Pb-Zn deposit has a close genetic relationship with the structural system of the black/fracture zone formed under ...As one of the typical deposits in the Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province,the Daliangzi Pb-Zn deposit has a close genetic relationship with the structural system of the black/fracture zone formed under the action of the NWW-approximately EW strike-slip structures in the metallogenic province.The R1 black/fracture zone has a close relationship with ore forming;however,the mechanism of the rock-and ore-controlling action of the structural system remains unclear.Based on a detailed analysis of the tectonite-mineralized alteration lithofacies of the R1 black/fracture zone,the tectonite-mineralized alteration lithofacies zones can be divided into four types in succession outward from the Pb-Zn mineralization center(F_(5),F_(100),and other faults),i.e.,(1)the brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone;(2)the stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone;(3)the veined pyrite-sulfide-dolomitic cataclasite facies zone;(4)the fine-veined calcite-black carbonized dolomite facies zone.With the evolution of the ore-forming fluid,the homogenization temperature decreases from Zone 1 to Zone 4;the salinity increases from Zone 1 to Zone 2 and then it decreases from Zones 3 and 4.The fluid density shows little change overall.The contents of Zn,Pb,Cu,Ga,Ge,Cd,Ag,and other metallogenic elements,Zn/Pb ratio,and CaO/MgO mole ratio decrease gradually from Zone 1 to Zone 4,and the REE fractionation,calcilization,silicification,and pyritization enhance gradually from Zone 1 to Zone 4.This series of changes is the product of diapirism(cryptoexplosion)of strike-slip structures and the black/fracture zone,among which the second-order structures derived from NWW-approximately EW-striking dextral shear-tension faults F_(1)and F_(15)control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones.Therefore,this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of the black/fracture zone and proposes that Zones 1 and 2 provide important prospecting criteria.展开更多
The development of geological lamination in shale reservoirs influences fracture propagation during hydraulic stimulation,and the fracture generation mechanism as it propagates through the laminated interface is close...The development of geological lamination in shale reservoirs influences fracture propagation during hydraulic stimulation,and the fracture generation mechanism as it propagates through the laminated interface is closely related to fracturing effects.In this paper,the laminated shale was selected to conduct three-point bending experiments using digital image correlation(DIC)and acoustic emission(AE)techniques,which revealed that the propagation path of cross-layer fractures exhibits dislocation features.The cohesive fracture mechanism of cross-layer fractures is investigated from the viewpoint of the fracture process zone(FPZ),which displays the characteristics of intermittence and dislocation during fracture development.A computational criterion for predicting the dislocation of cross-layer fracture at the interface is proposed,which shows that the maximum dislocation range does not exceed 72%of the FPZ length.Considering the mechanical differences between adjacent layers of laminated shale,the cohesive zone model of cross-layer fracture is discussed,from which the constitutive relationship and fracture energy during FPZ development are characterized,and the discontinuous nature of the constitutive relationship is found.This study improves the understanding of the geometry and cohesive fracture mechanism of the cross-layer fracture and provides valuable insights for field fracturing in shale reservoirs.展开更多
This study investigated the impact of a non-causative fault on the dynamic response of a nearby lined tunnel under the incidence of plane SV waves using the indirect boundary element method.The effects of several crit...This study investigated the impact of a non-causative fault on the dynamic response of a nearby lined tunnel under the incidence of plane SV waves using the indirect boundary element method.The effects of several critical parameters,such as the incident frequency,the inclination degree of the fault,the distance between the fault and the tunnel on the hoop stress of the lined inner and outer walls,were explored intensively.The numerical results indicated that the non-causative fault could significantly change the hoop stress distribution of inner and outer surfaces of the tunnels.In general,for the vertically incident seismic waves,when the tunnel was located in the foot wall(under the fault),the hoop stress within the tunnel was significantly greater than that of the tunnels in the non-fault half space,with an amplification factor of up to 117%.The amplification effect became more pronounced as the fault dip angle increased.However,when the tunnel was located in the hanging wall(above the fault),the non-causative fault could produce a significant shielding effect on the dynamic response of the tunnel under high frequency wave incidence,with the reduction of hoop stress being up to 81%.For lowfrequency waves,though,the fault could lead to an increase of the hoop stress of the tunnel of up to 152%.The research results will provide a reference for the seismic design and safety protection of underground structures in non-causative fault sites.展开更多
Understanding the strength characteristics and deformation behaviour of the tunnel surrounding rock in a fault zone is significant for tunnel stability evaluation.In this study,a series of unconfined compression tests...Understanding the strength characteristics and deformation behaviour of the tunnel surrounding rock in a fault zone is significant for tunnel stability evaluation.In this study,a series of unconfined compression tests were conducted to investigate the mechanical characteristics and failure behaviour of completely weathered granite(CWG)from a fault zone,considering with height-diameter(h/d)ratio,dry densities(ρd)and moisture contents(ω).Based on the experimental results,a regression mathematical model of unconfined compressive strength(UCS)for CWG was developed using the Multiple Nonlinear Regression method(MNLR).The research results indicated that the UCS of the specimen with a h/d ratio of 0.6 decreased with the increase ofω.When the h/d ratio increased to 1.0,the UCS increasedωwith up to 10.5%and then decreased.Increasingρd is conducive to the improvement of the UCS at anyω.The deformation and rupture process as well as final failure modes of the specimen are controlled by h/d ratio,ρd andω,and the h/d ratio is the dominant factor affecting the final failure mode,followed byωandρd.The specimens with different h/d ratio exhibited completely different fracture mode,i.e.,typical splitting failure(h/d=0.6)and shear failure(h/d=1.0).By comparing the experimental results,this regression model for predicting UCS is accurate and reliable,and the h/d ratio is the dominant factor affecting the UCS of CWG,followed byρd and thenω.These findings provide important references for maintenance of the tunnel crossing other fault fractured zones,especially at low confining pressure or unconfined condition.展开更多
Water flooding disasters are one of the five natural coal-mining disasters that threaten the lives of coal miners. The main causes of this flooding are water-conducting fractured zones within coal seams. However, when...Water flooding disasters are one of the five natural coal-mining disasters that threaten the lives of coal miners. The main causes of this flooding are water-conducting fractured zones within coal seams. However, when resistivity methods are used to detect water-conducting fractured zones in coal seams, incorrect conclusions can be drawn because of electrical anisotropy within the water-conducting fractured zones. We present, in this paper, a new geo-electrical model based on the geology of water-conducting fractured zones in coal seams. Factors that influence electrical anisotropy were analyzed, including formation water resistivity, porosity, fracture density, and fracture surface roughness, pressure, and dip angle. Numerical simulation was used to evaluate the proposed electrical method. The results demonstrate a closed relationship between the shape of apparent resistivity and the strike and dip of a fracture. Hence, the findings of this paper provide a practical resistivity method for coal-mining production.展开更多
In the process of using the original key stratum theory to predict the height of a water-flowing fractured zone(WFZ),the influence of rock strata outside the calculation range on the rock strata within the calculation...In the process of using the original key stratum theory to predict the height of a water-flowing fractured zone(WFZ),the influence of rock strata outside the calculation range on the rock strata within the calculation range as well as the fact that the shape of the overburden deformation area will change with the excavation length are ignored.In this paper,an improved key stratum theory(IKS theory)was proposed by fixing these two shortcomings.Then,a WFZ height prediction method based on IKS theory was established and applied.First,the range of overburden involved in the analysis was determined according to the tensile stress distribution range above the goaf.Second,the key stratum in the overburden involved in the analysis was identified through IKS theory.Finally,the tendency of the WFZ to develop upward was determined by judging whether or not the identified key stratum will break.The proposed method was applied and verified in a mining case study,and the reasons for the differences in the development patterns between the WFZs in coalfields in Northwest and East China were also fully explained by this method.展开更多
基金financially supported by the Innovation Fund Research Project of State Key Laboratory for Geomechanics and Deep Underground Engineering,China University of Mining and Technology(Grant No.SKLGDUEK202201)。
文摘To address the issue of extensive deformation in the Tabaiyi Tunnel caused by the fault zone,nuclear magnetic resonance(NMR)technology was employed to analyze the physical and mechanical properties of waterabsorbing mudstone.This analysis aimed to understand the mechanism behind the significant deformations.Drawing from the principle of excavation stress compensation,a support scheme featuring NPR anchorcables and an asymmetric truss support system was devised.To validate the scheme,numerical analysis using a combination of the Discrete Element Method(DEM)-Finite Element Method(FEM)was conducted.Additionally,similar material model tests and engineering measurements were carried out.Field experiments were also performed to evaluate the NPR anchor-cable and truss support system,focusing on anchor cable forces,pressures between the truss and surrounding rock,pressures between the initial support and secondary lining,as well as the magnitude of settlement and convergence deformation in the surrounding rock.The results indicate that the waterinduced expansion of clay minerals,resulting from damage caused by fissure water,accelerated the softening of the mudstone's internal structure,leading to significant deformations in the Tabaiyi Tunnel under high tectonic stress.The original support design fell short as the length of the anchor rods was smaller than the expansion depth of the plastic zone.As a result,the initial support structure bore the entire load from the surrounding rock,and a non-coupled deformation contact was observed between the double-arch truss and the surrounding rock.The adoption of NPR asymmetric anchor-cable support effectively restrained the expansion and asymmetric distribution characteristics of the plastic zone.Considering the mechanical degradation caused by water absorption in mudstone,the rigid constraint provided by the truss proved crucial for controlling the stability of the surrounding rock.These research findings hold significant implications for managing large deformations in soft rock tunnels situated within fractured zones under high tectonic stress conditions.
基金This work was supported by the Guangdong Basic and Applied Basic Research Foundation(Grant No.2021A1515110304)the Na-tional Natural Science Foundation of China(Grant Nos.42077246 and 52278412).
文摘Grouting is a widely used approach to reinforce broken surrounding rock mass during the construction of underground tunnels in fault fracture zones,and its reinforcement effectiveness is highly affected by geostress.In this study,a numerical manifold method(NMM)based simulator has been developed to examine the impact of geostress conditions on grouting reinforcement during tunnel excavation.To develop this simulator,a detection technique for identifying slurry migration channels and an improved fluid-solid coupling(FeS)framework,which considers the influence of fracture properties and geostress states,is developed and incorporated into a zero-thickness cohesive element(ZE)based NMM(Co-NMM)for simulating tunnel excavation.Additionally,to simulate coagulation of injected slurry,a bonding repair algorithm is further proposed based on the ZE model.To verify the accuracy of the proposed simulator,a series of simulations about slurry migration in single fractures and fracture networks are numerically reproduced,and the results align well with analytical and laboratory test results.Furthermore,these numerical results show that neglecting the influence of geostress condition can lead to a serious over-estimation of slurry migration range and reinforcement effectiveness.After validations,a series of simulations about tunnel grouting reinforcement and tunnel excavation in fault fracture zones with varying fracture densities under different geostress conditions are conducted.Based on these simula-tions,the influence of geostress conditions and the optimization of grouting schemes are discussed.
基金supported by the International Cooperation and Exchange Program of China (No. 31211130305)theYouth Talent Team Program of Institute of Mountain Hazards and Environment, Chinese Academy of Sciences (No.SDSQB-2012-01)
文摘The Wenchuan earthquake triggered cascading disasters of landslides and debris flows that caused severe vegetation damage. Fracture zones can affect geodynamics and spatial pattern of vegetation damage. A segment tracing algorithm method was applied for identifying the regional fracture system through lineament extractions from a shaded digital elevation model with 25 m mesh for southern Wenchuan. Remote sensing and geographic information system techniques were used to analyze the spatiotemporal vegetation pattern. The relationship between vegetation type identified from satellite images and lineament density was used to characterize the distribution patterns of each vegetation type according to fracture zones. Broad-leaved forest, mixed forest, and farmland persist in areas with moderate lineament density. Deciduous broad-leaved and coniferous forest persists in less frac- tured areas. Shrub and meadow seem to be relatively evenly distributed across all lineament densities.Meadow, farmland, and shrub persist in the fractured areas. Changes of spatial structure and correlation between vegetation patterns before and after the earthquake were examined using semivariogram analysis of normalized difference vegetation indices derived from Landsat enhanced thematic mapper images. The sill values of the semivariograms show that the spatial heterogeneity of vegetation covers increased after the earthquake. Moreover, the anisotropic behaviors of the semivariograms coincide with the vegetation changes due to the strikes of fracture zones.
基金Supported by the National Key R&D Program(2018YFC0604501).
文摘To study the heights of the caved zone and water-conducting fracture zone in backfill mining,the failure mechanism of strata during backfill mining was analyzed,and a method for determining the heights of the two zones was proposed based on key strata theory.The movement and failure regularity of the strata above the backfilling panel were revealed through numerical simulation.Considering the geologic conditions of the CT101 backfilling panel,the height of the fracture zone was determined using the proposed method along with empirical calculation,numerical simulation,and borehole detection.The results of the new calculation method were similar to in situ measurements.The traditional empirical formula,which is based on the equivalent mining height model,resulted in large errors during calculation.The findings indicate the reliability of the new method and demonstrate its significance for creating reference data for related studies.
文摘Prediction of the height of a water-flowing fracture zone(WFFZ)is the foundation for evaluating water bursting conditions on roof coal.By taking the Binchang mining area as the study area and conducting an in-depth study of the influence of coal seam thickness,burial depth,working face length,and roof category on the height of a WFFZ,we proposed that the proportion of hard rock in different roof ranges should be used to characterise the influence of roof category on WFFZ height.Based on data of WFFZ height and its influence index obtained from field observations,a prediction model is established for WFFZ height using a combination of a genetic algorithm and a support-vector machine.The reliability and superiority of the prediction model were verified by a comparative study and an engineering application.The results show that the main factors affecting WFFZ height in the study area are coal seam thickness,burial depth,working face length,and roof category.Compared with multiple-linear-regression and back-propagation neural-network approaches,the height-prediction model of the WFFZ based on a genetic-algorithm support-vector-machine method has higher training and prediction accuracy and is more suitable for WFFZ prediction in the mining area.
文摘In Xikuangshan antimony ore-field, the western fracture zone is a composite of major fault, F75, and its secondary faults, such as F71, F72 and F3 etc.. On plane, the fracture zone scatters from southwest to northeast, and concentrates from upper to deeper level on profile. All ore-bodies exist in the carbonate of footwall of the major fault or that of the footwall of its secondary faults. From 480 m and 320 m to 120 m level, the fractal dimensional number of the fault system decreases from 1.482 2 and 1.448 6 to 1.339 2, which indicates the form of fracture zone becoming more simple at deeper level. And in five sub-ranges, the III and IV sub-ranges are the known area, and the I, II and V sub-ranges are unknown. The fractal studies of the western fracture zone in these sub-ranges show that the fractal dimensional numbers of the I and II, being 1.201 5 and 1.278 0, respectively, are smaller than that of the III and IV, being 1.475 9 and 1.576 9, respectively; and that of the V, being 1.571 2, keeps with that of the III, IV sub-ranges. So mineralization is not well in I and II sub-ranges, and V sub-range is the best to benefit mineralization.
文摘Planktic foraminifera from the calcareous substrate of a ferromanganese crust in the Vityaz Fracture Zone （VFZ）, Central Indian Ridge were studied to reconstruct the early Pliocene paleoceanography of this region. Eleven species of planktic foraminifera were encountered, among them Globorotalia menardii, Neogloboquadrina dutertrei, Globigerina bulloides and Globigerinoides tuber are prominent. Predominance of N. dutertrei in the top 3 cm of the carbonate substrate is attributed to an influx of fresh water which eventually triggered their productivity by increasing the nutrient level. The presence of G. bulloides and G. menardii in significant proportions in deeper layers suggests the prevalence of open ocean upwelling. The bulk chemical compositions of the substrate at different depth intervals indicates higher enrichment of trace metals in the upper sections which could have been supplied through oceanic water by the chemical weathering of terrestrial matter during the peak of Pliocene Asian monsoon. Thus, it is concluded that during the early Pliocene the biogenic components of the substrate were distinctly contributed by both upwelling and productivity triggered by an influx of fresh water originating from the intensification of the Asian monsoon during the early Pliocene Period.
文摘It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power Spectral Density） function is developed using wave propagation theory, while for vertical incidence of waves the cross-PSD function is composed by auto-PSD model, coherence model and site response model. As the seismic input, the eross-PSD function is used to calculate the the axial and lateral seismic responses of underground pipeline through the fracture zone. The results show that the incident directions of seismic waves, width and soil property of the fracture zone have great influence on underground pipeline. It is suggested that the flexible joints with appropriate stiffness should be added into the pipeline near the interfaces between the fracture zone and the surrounded media.
基金The Program for New Century Excellent Talents in University ( No. NCET-06-0649)the Natural Science Foundation of Hubei Province (No.2005ABA303)
文摘Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided into three zones, including elastic zone, plastic damage zone and shear fracture zone for assessing the stability of the tunnel surrounding rock. By local hydrogeology, the stresses of surrounding rock of Jinshazhou circular tunnel was analyzed and the stress solutions on the elastic and plastic damage zones were obtained by applying the theories of fluid-solid coupling and elasto-plastic damage mechanics. The shear fracture zone generated by joints was studied and its range was determined by using Molar-Coulomb strength criterion. Finally, the correctness of the theoretical results was validated by comparing the scopes of shear fracture zones calculated in this paper with those from literature.
基金Supported by Project of the Foundation of China Geological Survey(No.1212010071012)supported by the foundation of China Geological Survey Project(1212010071012)
文摘The mylonites occurred in the fracture zones are studied by dynamically recrystallized quartz grains.The natural microstructures in mylonites are simulated and the deformation conditions of mylonitization are estimated by fractal analysis,recrystallized grain size paleopiezometer and flow laws of quartzite.Depending on fractal analysis,the deformation temperature of mylonitization is approximately 600℃,which presents high greenschist facies to low amphibolite facies.The mylonitization occurred at differential stresses of 9.1--10.7MPa(lower limits).Compared with extrapolation of quartzite flow laws and estimates of fractal analysis,the strain rate of mylonitization is under 10-13.8/s.
文摘We have imaged rock density distribution beneath Liwa fracture zone in the southern part of the the Sumatran Fault Zone by modelling and inverting Bouguer gravity data in two-and three-dimensional environments, respectively. The purpose of this study is aimed to figure out the subsurface distribution of rock densities associated with subsurface basement structure representing the evidence of trans-tensional tectonic product in the SF. In the gravity modeling, to eliminate distortions to the measured gravity values before modelling and inverting the data, Bouguer anomalies obtained in field measurements are reduced to the horizontal plane of z = +800 m as a representation of the average elevation in Liwa. For the inversion, we used algorithm implementing depth-and minimum volume weighting parameters in order to obtain a smooth model with better vertical resolution. The two-dimensional models show clearly surface topography of the basement rocks and the presence of normal faults. The reduced Bouguer anomaly of +800 m elevation shows the presence of structural lineaments extending primarily in a northwest-southeast direction, parallel to Sumatran Fault Zone and older graben faults showing a negative flower structure. From the three-dimensional inversion, the model illustrates an increase of density contrast, lower values being found near the surface and higher values in the deeper parts. The lower density contrast of 0.15 to 0.3 g/cm<sup>3</sup> found in the rock groups at depths of 2 km and less is characteristic of relatively homogeneous and poorly compacted rocks. Rocks with moderate to high density contrast (>1.0 g/cm<sup>3</sup>) are recognized at depths of over 2 km. This model suggests a change of basement morphology as a function of depth, and delineates structural lineaments extending in northwest-southeast direction. This study supports the previous thought that Liwa area is underlain by graben structures, formed by trans-tensional tectonic events. Higher-density Tertiary volcanic breccia and lower-density Quaternary volcanic products of the Ranau Formation form the basement rocks and the overlying younger sediments, respectively.
基金funded by the National Natural Science Foundation of China(Grant Nos.12172230,U22A20166)the Department of Science and Technology of Guangdong Province(Grant No.2019ZT08G315).
文摘Understanding the anisotropic fracture behavior and the characteristics of the fracture process zone(FPZ)under size effects in laminated rocks,as well as its role in rock fracturing,is crucial for various engineering applications.In this study,three-point bending tests were conducted on shale specimens with varying bedding angles and sizes.The anisotropic characteristics and size effects of fracture parameters were revealed.A comparative analysis was performed on the evolutions of FPZs computed using size effect theory,digital image correlation(DIC),and linear elastic fracture mechanics.The results divulged that:(i)With increasing bedding angles,there is a noticeable decrease in apparent fracture toughness(KICA),apparent fracture energy(GICA),and nominal strength(σ_(Nu)).When the bedding angle of shale is less than 45°,the crack propagation and fracture parameters are mainly influenced by the matrix.Contrary,shale with bedding angles greater than 60°,the crack propagation and fracture parameters are mainly controlled by the bedding.When the bedding angle is between 45°and 60°,the fracture propagation evolves from permeating the matrix to extending along the bedding;(ii)The fracture parameters exhibit significant size dependent behavior,as KICA and GICA rise with increasing specimen size,butσNu falls with increasing specimen sizes.The fracture parameters align with the theoretical predictions of Bažant size effect law;and(iii)The lengths of DIC-based FPZ,effective FPZ,and inelastic zone follow W-shape variations with bedding angle.The dimensionless sizes of FPZ and inelastic zone decrease with specimen size,indicating a size effect.Furthermore,there is a negative relation between KICA and the dimensionless size of the FPZ,whileσNu is positively correlated to the dimensionless size of the FPZ.This highlights the essential role of the FPZ in the size effect of rock fracture.The bedding angle exerts an influence on the FPZ,subsequently affecting the anisotropic fracture and size-dependent behavior of shale.
基金support from the National Natural Science Foundation of China(Grant No.52274009).
文摘During drilling operations in deep fractured tight gas reservoirs,lost circulation of working fluid frequently occurs due to the formationʼs low pressure-bearing capacity.Adding lost circulation materials(LCMs)to drilling fluids is the most common method for controlling lost circulation.Among these,granular LCMs are widely used,but the application frequency of flaky LCMs has been increasing annually due to their unique morphology.However,the migration and plugging behavior of flaky LCMs within fractures,and the mechanisms enhancing the pressure-bearing capacity of the plugging zone are not well understood.Therefore,this study conducted visual plugging experiments and dynamic fracture plugging experiments to evaluate the plugging mode and pressure-bearing capacity of the plugging slurry with various particle sizes and concentrations of flaky LCMs.The experimental results demonstrate that the fracture plugging process can be divided into four stages:uniform flow stage of the plugging slurry,formation and development stage of the bridging area,formation and development stage of the plugging area,and pressure-bearing stage of the plugging zone.The inclusion of flaky LCMs notably reduces the duration of stages 1 and 2,while simultaneously increasing the proportion of the plugging zone and enhancing its surface porosity.Flaky LCMs reduce the effective fracture width through“interception”and“co-bridging”modes,thus improving plugging zone formation efficiency.Appropriate particle size and concentration of flaky LCMs increase the area and length of the plugging zone.This reduces the fracture width increment caused by injection pressure and enhances frictional force between the plugging zone and fracture surface,thereby improving the pressure-bearing capacity of the plugging zone.However,excessively high concentrations of flaky LCMs result in decreased structural stability of the plugging zone,and excessively large particle sizes increase the risk of plugging outside fracture inlet.The recommended concentration of flaky LCMs in the plugging slurry is 2%–3%,with a particle size 1.2 to 1.5 times that of the bridging granular LCMs and not exceeding twice the fracture width.This study provides a theoretical foundation for selecting LCMs and designing plugging formulations for field applications.
基金supported by the projects(Grant No.:52304118)supported by National Natural Science Foundation of China,the Scientific Research Foundation for High-level Talents of Anhui University of Science and Technology(2023yjrc18)the Open Fund of the State Key Laboratory of Mining Response and Disaster Prevention and Control in Deep Coal Mine(Grant No.:SKLMRDPC23KF08).
文摘This study investigates the fracture characteristics and the fracture process zone(FPZ)of mode I fracture in sandstone,aiming to analyze the propagation behaviors of mode I crack under different freeze-thaw cycles.Semicircular bending tests(SCB)were conducted using different freeze-thaw cycles to evaluate mode I fracture toughness,FPZ dynamics,and macroscopic microscopic features.Digital image correlation(DIC)and scanning electron microscopy(SEM)techniques were employed for detailed analysis.Experimental results reveal that freeze-thaw cycling leads to the widening of both preexisting and newly formed microcracks between internal particles.Under external loading,crack propagation deviates from prefabricated paths,forming serrated crack patterns.The FPZ initiates at the prefabricated crack tip and extends toward the loading end,exhibiting an arcshaped tip shape.The FPZ length increases with loading but decreases after reaching a peak value.With additional freeze-thaw cycles,the maximum FPZ length first increases and then diminishes.
基金funded by the programs of the National Natural Science Foundation(Nos.42172086,41572060,U1133602)the Program of‘Yunling Scholar’of Yunnan province(2014)+1 种基金the Projects of the Yunnan Engineering Laboratory of Mineral Resources Prediction and Evaluation(YM Lab)(2010)the Innovation Team of Yunnan Province and KMUST(2008,2012).
文摘As one of the typical deposits in the Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province,the Daliangzi Pb-Zn deposit has a close genetic relationship with the structural system of the black/fracture zone formed under the action of the NWW-approximately EW strike-slip structures in the metallogenic province.The R1 black/fracture zone has a close relationship with ore forming;however,the mechanism of the rock-and ore-controlling action of the structural system remains unclear.Based on a detailed analysis of the tectonite-mineralized alteration lithofacies of the R1 black/fracture zone,the tectonite-mineralized alteration lithofacies zones can be divided into four types in succession outward from the Pb-Zn mineralization center(F_(5),F_(100),and other faults),i.e.,(1)the brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone;(2)the stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone;(3)the veined pyrite-sulfide-dolomitic cataclasite facies zone;(4)the fine-veined calcite-black carbonized dolomite facies zone.With the evolution of the ore-forming fluid,the homogenization temperature decreases from Zone 1 to Zone 4;the salinity increases from Zone 1 to Zone 2 and then it decreases from Zones 3 and 4.The fluid density shows little change overall.The contents of Zn,Pb,Cu,Ga,Ge,Cd,Ag,and other metallogenic elements,Zn/Pb ratio,and CaO/MgO mole ratio decrease gradually from Zone 1 to Zone 4,and the REE fractionation,calcilization,silicification,and pyritization enhance gradually from Zone 1 to Zone 4.This series of changes is the product of diapirism(cryptoexplosion)of strike-slip structures and the black/fracture zone,among which the second-order structures derived from NWW-approximately EW-striking dextral shear-tension faults F_(1)and F_(15)control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones.Therefore,this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of the black/fracture zone and proposes that Zones 1 and 2 provide important prospecting criteria.
基金financiallysupported by the Excellent Young Fund of Sinopec Petroleum Exploration and Production Research Institute(Grant No.YK2024009)the National Natural Science Foundation of China(Grant Nos.U23B6004 and 51925405).
文摘The development of geological lamination in shale reservoirs influences fracture propagation during hydraulic stimulation,and the fracture generation mechanism as it propagates through the laminated interface is closely related to fracturing effects.In this paper,the laminated shale was selected to conduct three-point bending experiments using digital image correlation(DIC)and acoustic emission(AE)techniques,which revealed that the propagation path of cross-layer fractures exhibits dislocation features.The cohesive fracture mechanism of cross-layer fractures is investigated from the viewpoint of the fracture process zone(FPZ),which displays the characteristics of intermittence and dislocation during fracture development.A computational criterion for predicting the dislocation of cross-layer fracture at the interface is proposed,which shows that the maximum dislocation range does not exceed 72%of the FPZ length.Considering the mechanical differences between adjacent layers of laminated shale,the cohesive zone model of cross-layer fracture is discussed,from which the constitutive relationship and fracture energy during FPZ development are characterized,and the discontinuous nature of the constitutive relationship is found.This study improves the understanding of the geometry and cohesive fracture mechanism of the cross-layer fracture and provides valuable insights for field fracturing in shale reservoirs.
基金supported by the National Natural Science Foundation of China(Grant Nos.51878434,51878108)Natural Science Foundation of Tianjin(Grant No.18JCZDJC 39200)Program of Tianjin Science and Technology Plan(Grant No.18ZXGDGX00050).
文摘This study investigated the impact of a non-causative fault on the dynamic response of a nearby lined tunnel under the incidence of plane SV waves using the indirect boundary element method.The effects of several critical parameters,such as the incident frequency,the inclination degree of the fault,the distance between the fault and the tunnel on the hoop stress of the lined inner and outer walls,were explored intensively.The numerical results indicated that the non-causative fault could significantly change the hoop stress distribution of inner and outer surfaces of the tunnels.In general,for the vertically incident seismic waves,when the tunnel was located in the foot wall(under the fault),the hoop stress within the tunnel was significantly greater than that of the tunnels in the non-fault half space,with an amplification factor of up to 117%.The amplification effect became more pronounced as the fault dip angle increased.However,when the tunnel was located in the hanging wall(above the fault),the non-causative fault could produce a significant shielding effect on the dynamic response of the tunnel under high frequency wave incidence,with the reduction of hoop stress being up to 81%.For lowfrequency waves,though,the fault could lead to an increase of the hoop stress of the tunnel of up to 152%.The research results will provide a reference for the seismic design and safety protection of underground structures in non-causative fault sites.
基金supported by the National Natural Science Foundation of China,NSFC(No.42202318).
文摘Understanding the strength characteristics and deformation behaviour of the tunnel surrounding rock in a fault zone is significant for tunnel stability evaluation.In this study,a series of unconfined compression tests were conducted to investigate the mechanical characteristics and failure behaviour of completely weathered granite(CWG)from a fault zone,considering with height-diameter(h/d)ratio,dry densities(ρd)and moisture contents(ω).Based on the experimental results,a regression mathematical model of unconfined compressive strength(UCS)for CWG was developed using the Multiple Nonlinear Regression method(MNLR).The research results indicated that the UCS of the specimen with a h/d ratio of 0.6 decreased with the increase ofω.When the h/d ratio increased to 1.0,the UCS increasedωwith up to 10.5%and then decreased.Increasingρd is conducive to the improvement of the UCS at anyω.The deformation and rupture process as well as final failure modes of the specimen are controlled by h/d ratio,ρd andω,and the h/d ratio is the dominant factor affecting the final failure mode,followed byωandρd.The specimens with different h/d ratio exhibited completely different fracture mode,i.e.,typical splitting failure(h/d=0.6)and shear failure(h/d=1.0).By comparing the experimental results,this regression model for predicting UCS is accurate and reliable,and the h/d ratio is the dominant factor affecting the UCS of CWG,followed byρd and thenω.These findings provide important references for maintenance of the tunnel crossing other fault fractured zones,especially at low confining pressure or unconfined condition.
基金supported by a project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutionsthe Fundamental Research Funds for the Central Universities 2014QNA88the National Natural Science Foundation(No.41674133)
文摘Water flooding disasters are one of the five natural coal-mining disasters that threaten the lives of coal miners. The main causes of this flooding are water-conducting fractured zones within coal seams. However, when resistivity methods are used to detect water-conducting fractured zones in coal seams, incorrect conclusions can be drawn because of electrical anisotropy within the water-conducting fractured zones. We present, in this paper, a new geo-electrical model based on the geology of water-conducting fractured zones in coal seams. Factors that influence electrical anisotropy were analyzed, including formation water resistivity, porosity, fracture density, and fracture surface roughness, pressure, and dip angle. Numerical simulation was used to evaluate the proposed electrical method. The results demonstrate a closed relationship between the shape of apparent resistivity and the strike and dip of a fracture. Hence, the findings of this paper provide a practical resistivity method for coal-mining production.
基金supported by the Key Projects of Natural Science Foundation of China(No.41931284)the Scientific Research Start-Up Fund for High-Level Introduced Talents of Anhui University of Science and Technology(No.2022yjrc21).
文摘In the process of using the original key stratum theory to predict the height of a water-flowing fractured zone(WFZ),the influence of rock strata outside the calculation range on the rock strata within the calculation range as well as the fact that the shape of the overburden deformation area will change with the excavation length are ignored.In this paper,an improved key stratum theory(IKS theory)was proposed by fixing these two shortcomings.Then,a WFZ height prediction method based on IKS theory was established and applied.First,the range of overburden involved in the analysis was determined according to the tensile stress distribution range above the goaf.Second,the key stratum in the overburden involved in the analysis was identified through IKS theory.Finally,the tendency of the WFZ to develop upward was determined by judging whether or not the identified key stratum will break.The proposed method was applied and verified in a mining case study,and the reasons for the differences in the development patterns between the WFZs in coalfields in Northwest and East China were also fully explained by this method.
