Composite films of different contents were prepared by Fe73.5Cu1Nb3Si13.5B9 powder as compound phase and silicone rubber as matrix phase. The thickness of film is 200 μm. Values of impedance, Z, under pressure stress...Composite films of different contents were prepared by Fe73.5Cu1Nb3Si13.5B9 powder as compound phase and silicone rubber as matrix phase. The thickness of film is 200 μm. Values of impedance, Z, under pressure stress were measured by TH2816LCR digital bridge. LYYL-500N high-grade-type microcomputer control pressure testing machine was used to conduct program control loading with a speed of 0.1 mm·min^-1. The results show that composite films of different contents （25 vol%, 30 vol%, and 35 vol%） have excellent force-sensitive properties in both loading process and unloading process, especially when the stress is below 0.2 MPa, the stress- impedance （SI） and ＋｜k｜ values of composite films are much higher than that in the range of 0.2-1.0 MPa. The force- sensitive properties of loading process are superior to unloading process. While the frequency is 1 kHz, the force-sensitive properties of composite films are better than 50 kHz. The optimal temperature of powder heat treatment is 500 ℃. Composite film which was prepared by this kind of powder has a good force-sensitive property.展开更多
This study investigates the properties of high-purity starches extracted from Polygonum multiflorum(PMS)and Smilax glabra(SGS).The starches were characterized by scanning electron microscopy,Fouriertransform infrared ...This study investigates the properties of high-purity starches extracted from Polygonum multiflorum(PMS)and Smilax glabra(SGS).The starches were characterized by scanning electron microscopy,Fouriertransform infrared spectroscopy,X-ray diffraction,high-performance anion-exchange chromatography,and differential scanning calorimetry.Significant differences were observed in their morphological,physicochemical,and functional properties.PMS had a smaller particle size(13.68 μm),irregular polygonal shape,A-type,lower water absorption(62.67 %),and higher oil absorption(51.17 %).In contrast,SGS exhibited larger particles(31.75 μm),a nearly spherical shape,B-type,higher crystallinity(50.66 %),and greater amylose content(21.54 %),with superior thermal stability,shear resistance,and gelatinization enthalpy.SGS also contained higher resistant starch(83.28 %) and longer average chain length(20.58 %),but showed lower solubility,swelling power,light transmittance,and freeze-thaw stability.The physicochemical properties differences in crystal pattern and particle morphology between PMS and SGS lead to distinct behaviors during in vitro digestion and fermentation.These findings highlight the potential of medicinal plant starches in functional ingredients and industrial processes.展开更多
Herein,antibacterial silver‑doped fluorescent carbon dots(Ag‑CDs)were synthesized through a stepwise hydrothermal method,with polyethyleneimine(PEI),citric acid(CA),and silver nitrate(AgNO3)serving as precursors.The a...Herein,antibacterial silver‑doped fluorescent carbon dots(Ag‑CDs)were synthesized through a stepwise hydrothermal method,with polyethyleneimine(PEI),citric acid(CA),and silver nitrate(AgNO3)serving as precursors.The applicability and antimicrobial efficacy of these nanomaterials were systematically investigated for metal ion sensing.Experimental evidence demonstrated that the Ag‑CDs exhibited a pronounced fluorescence quenching response toward ferric ions(Fe^(3+)),enabling their quantitative determination via a linear concentration‑dependent relationship.These Ag‑CDs exhibited significant inhibitory effects on biofilm growth and disruption for both Escherichia coli and Staphylococcus aureus.Mechanism investigations indicate that Ag‑CDs induced the death of Escherichia coli and Pseudomonas aeruginosa by disrupting their bacterial morphology and structure,triggering the generation of intracellular reactive oxygen species(ROS),and impairing their antioxidant defense system.展开更多
Oxygen carriers play a fundamental role in chemical looping combustion(CLC).Iron-based carriers have been extensively investigated owing to their abundance and environmentally friendly.However,the reactivity and separ...Oxygen carriers play a fundamental role in chemical looping combustion(CLC).Iron-based carriers have been extensively investigated owing to their abundance and environmentally friendly.However,the reactivity and separability of iron-based carriers require further enhancement.This study investigates the effect of the concentration of Mn doping on reactivity,elastic properties and magnetic properties based on density functional theory(DFT)calculations.Theoretical results demonstrate that Mn doping effectively enhances reactivity by reducing the oxygen vacancy formation energy(E_(vac))from 2.33 to 0.87 eV.However,Mn doping introduces HV/EV Ms lattice distortions that deteriorate elastic properties,thereby reducing wear resistance,as evidenced by a 54.54%decrease in the hardness-to-Young's modulus ratio(H_(v)/E_(v))forα-Fe_(2)O_(3)and an 83.33%reduction for Fe_(3)O_(4).Furthermore,Mn doping also modifies magnetic properties.The maximum of saturation magnetization(M_(s))of Fe_(3)O_(4)reaches 121.02 emu/g at 33.33%Mn doping concentration.Finally,systematic evaluation identifies 33.33%as the optimal Mn doping concentration,achieving a balance in enhanced reactivity,superior magnetic performance,and retained elastic stability.展开更多
The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solutio...The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.展开更多
Six new lanthanide complexes:[Ln(3,4-DEOBA)3(4,4'-DM-2,2'-bipy)]2·2C_(2)H_(5)OH,[Ln=Dy(1),Eu(2),Tb(3),Sm(4),Ho(5),Gd(6);3,4-DEOBA-=3,4-diethoxybenzoate,4,4'-DM-2,2'-bipy=4,4'-dimethyl-2,2'...Six new lanthanide complexes:[Ln(3,4-DEOBA)3(4,4'-DM-2,2'-bipy)]2·2C_(2)H_(5)OH,[Ln=Dy(1),Eu(2),Tb(3),Sm(4),Ho(5),Gd(6);3,4-DEOBA-=3,4-diethoxybenzoate,4,4'-DM-2,2'-bipy=4,4'-dimethyl-2,2'-bipyridine]were successfully synthesized by the volatilization of the solution at room temperature.The crystal structures of six complexes were determined by single-crystal X-ray diffraction technology.The results showed that the complexes all have a binuclear structure,and the structures contain free ethanol molecules.Moreover,the coordination number of the central metal of each structural unit is eight.Adjacent structural units interact with each other through hydrogen bonds and further expand to form 1D chain-like and 2D planar structures.After conducting a systematic study on the luminescence properties of complexes 1-4,their emission and excitation spectra were obtained.Experimental results indicated that the fluorescence lifetimes of complexes 2 and 3 were 0.807 and 0.845 ms,respectively.The emission spectral data of complexes 1-4 were imported into the CIE chromaticity coordinate system,and their corre sponding luminescent regions cover the yellow light,red light,green light,and orange-red light bands,respectively.Within the temperature range of 299.15-1300 K,the thermal decomposition processes of the six complexes were comprehensively analyzed by using TG-DSC/FTIR/MS technology.The hypothesis of the gradual loss of ligand groups during the decomposition process was verified by detecting the escaped gas,3D infrared spectroscopy,and ion fragment information detected by mass spectrometry.The specific decomposition path is as follows:firstly,free ethanol molecules and neutral ligands are removed,and finally,acidic ligands are released;the final product is the corresponding metal oxide.CCDC:2430420,1;2430422,2;2430419,3;2430424,4;2430421,5;2430423,6.展开更多
The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance You...The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance Young's modulus measurements,and microstructure analysis,the effects of dislocation density,vacancy formation,and recrystallization on the alloy performance were clarified.Results indicate that increasing the rolling reduction enhances damping property due to higher dislocation density,whereas aging below the recrystallization temperature reduces damping property via dislocation pinning by the Suzuki effect.Recrystallization heat treatment restores the original structure and damping level.This alloy possesses tensile strength of approximately 1500 MPa and logarithmic decrement valueδ^(-1) in the range of 2×10^(-4)–3×10^(-4),demonstrating superior mechanical properties compared with the Ti-based alloys,which makes it an excellent candidate material for ultrasonic tools and medical applications.展开更多
The ionothermal reaction between CuCl_(2),1,4-bis(1,2,4-triazol-1-ylmethyl)benzene(BBTZ),and(NH_(4))_(6)Mo_(7)O_(24) in 1-ethyl-3-methylimidazolium bromide((Emim)Br)led to a new octamolybdate-based coordination polyme...The ionothermal reaction between CuCl_(2),1,4-bis(1,2,4-triazol-1-ylmethyl)benzene(BBTZ),and(NH_(4))_(6)Mo_(7)O_(24) in 1-ethyl-3-methylimidazolium bromide((Emim)Br)led to a new octamolybdate-based coordination polymer(Emim)2[Cu(BBTZ)_(2)(β-Mo_(8)O_(26))](Mo_(8)-CP).Mo_(8)-CP was characterized by elemental analysis,thermogravime-try,IR,powder X-ray diffraction,and single-crystal X-ray diffraction.In Mo_(8)-CP,structural analysis reveals that Cu coordinates with BBTZ ligands to form an interlocked 1D chain.These chains are further bridged by(β-Mo_(8)O_(26))^(4-)to construct a 3D coordination polymer.Notably,(Emim)^(+)acts as a structure-directing agent,occupying the channels of the 3D coordination polymer.Based on this unique structure,the ion exchange properties of Mo_(8)-CP toward rare-earth ions were investigated.It has been found that the luminescent color of the material can be successfully regulat-ed by introducing Eu^(3+)or Tb^(3+)through ion exchange.CCDC:2475110,Mo_(8)-CP.展开更多
The effect of element Ti on the microstructures and mechanical properties of as-cast and annealed NbTaMoWTi,(x=0,1,1.5,2)refractory high-entropy alloys(RHEAs)was investigated.Results show that after Ti addition,the as...The effect of element Ti on the microstructures and mechanical properties of as-cast and annealed NbTaMoWTi,(x=0,1,1.5,2)refractory high-entropy alloys(RHEAs)was investigated.Results show that after Ti addition,the as-cast alloys maintain their original single body-centered cubic(bcc)structure.As for the mechanical properties,compared with those without Ti addition,the strength and ductility of NbTaMoWTi,alloys increase by 93%and 215%,respectively.Furthermore,the NbTaMoWTi alloys exhibit outstanding thermal stability.After annealing at 1400 C,they still maintain the single bcc structure,and their mechanical properties are even slightly improved.However,annealing leads to a significant deterioration in the mechanical properties of high-Ti-content alloys(NbTaMoWTil and NbTaMoWTi2),owing to the formation of Ti-rich acicular phases.展开更多
The effects of channel segregation on the macro-and micro-scale chemical composition,microstructure,hardness,and tensile deformation behavior of Ti45Nb wires were investigated.The results show that wires with severe c...The effects of channel segregation on the macro-and micro-scale chemical composition,microstructure,hardness,and tensile deformation behavior of Ti45Nb wires were investigated.The results show that wires with severe channel segregation exhibit a macroscopic chemical composition identical to those without segregation,and 3D X-ray imaging result also reveals no abnormalities.After annealing,both types of wires exhibit an equiaxed single-phase microstructure with comparable grain sizes,suggesting that channel segregation has negligible influence on the macroscopic composition and grain size.Metallographic examination reveals that channel segregation manifests as spot-like features in the transverse section and band-like structures in the longitudinal section.EDS analysis identifies these regions as Ti-enriched segregations,with a Ti content higher than that of the surrounding matrix by approximately 4.42wt%.Compared to segregation-free wires,those containing extensive channel segregation demonstrate a 15.5%increase in ultimate tensile strength and a 12.3%increase in yield strength,but suffer a reduction in elongation and reduction of area by 19.8%and 18.9%,respectively.Furthermore,the mechanical properties of wires with segregation show significant fluctuations.Fractographic analysis reveals a larger fracture surface area in segregated wires.Severe dislocation pile-ups occur at the interfaces of these segregated regions,initiating microcrack nucleation.This promotes rapid crack propagation of the Ti45Nb wire,leading to a significant decrease in plasticity and reduction of area.展开更多
Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate indiv...Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate individual investigation due to variations in their composition and fabrication processes.This study presents a comprehensive investigation into evolution of the mechanical properties,surface microstructure,and composition of Shicolon-Ⅱ fibers subjected to argon heat treatment at temperatures ranging from 1300℃to 1700℃.The Shicolon-Ⅱ fibers are composed of small-sized β-SiC grains,SiC_(x)O_(y) amorphous phase,and a minor amount of graphite microcrystals.Following treatment in an argon atmosphere at 1300℃,the fibers maintain a monofilament tensile strength of 3.620 GPa,corresponding to a retention of 98.32%.This strength diminishes to 2.875 GPa,equating to a retention of 78.08%,after treatment at 1500℃.The reduction in mechanical properties of the fibers can be ascribed to the decomposition of the amorphous phase and the growth of β-SiC grains.Furthermore,creep resistance is an essential factor influencing the long-term performance of composite materials.After treatment at temperatures above 1400℃,the high-temperature creep resistance of the fibers is significantly enhanced due to growth of β-SiC grains.This study offers valuable theoretical insights into high-temperature applications of second-generation fibers,contributing to an enhanced understanding of their performance under extreme conditions.展开更多
Three zinc(Ⅱ),nickel(Ⅱ),and cadmium(Ⅱ)complexes,namely[Zn(μ-Htpta)(py)_(2)]n(1),[Ni(H_(2)biim)2(H_(2)O)2][Ni(tpta)(H_(2)biim)2(H_(2)O)]2·3H_(2)O(2),and[Cd_(3)(μ4-tpta)2(μ-dpe)_(3)]_(n)(3),have been construc...Three zinc(Ⅱ),nickel(Ⅱ),and cadmium(Ⅱ)complexes,namely[Zn(μ-Htpta)(py)_(2)]n(1),[Ni(H_(2)biim)2(H_(2)O)2][Ni(tpta)(H_(2)biim)2(H_(2)O)]2·3H_(2)O(2),and[Cd_(3)(μ4-tpta)2(μ-dpe)_(3)]_(n)(3),have been constructed hydrothermally at 160℃ using H_(3)tpta([1,1':3',1″-terphenyl]-4,4',5'-tricarboxylic acid),py(pyridine),H_(2)biim(2,2'-biimidazole),dpe(1,2-di(4-pyridyl)ethylene),and zinc,nickel and cadmium chlorides,resulting in the formation of stable crystalline solids which were subsequently analyzed using infrared spectroscopy,element analysis,thermogravimetric analysis,as well as structural analyses conducted via single-crystal X-ray diffraction.The findings from these single-crystal Xray diffraction studies indicate that complexes 1-3 form crystals within the monoclinic system P2_(1)/c space group(1)or triclinic system P1 space group(2 and 3),and possess 1D,0D,and 3D structures,respectively.Complex 1 demonstrated substantial catalytic efficiency and excellent reusability as a heterogeneous catalyst in the reaction of Knoevenagel condensation under ambient temperature conditions.In addition,complex 1 also showcased notable anti-wear performance when used in polyalphaolefin synthetic lubricants.CCDC:2449810,1;2449811,2;2449812,3.展开更多
(NbZrHfTi)C high-entropy ceramics,as an emerging class of ultra-high-temperature materials,have garnered significant interest due to their unique multi-principal-element crystal structure and exceptional hightemperatu...(NbZrHfTi)C high-entropy ceramics,as an emerging class of ultra-high-temperature materials,have garnered significant interest due to their unique multi-principal-element crystal structure and exceptional hightemperature properties.This study systematically investigates the mechanical properties of(NbZrHfTi)C high-entropy ceramics by employing first-principles density functional theory,combined with the Debye-Grüneisen model,to explore the variations in their thermophysical properties with temperature(0–2000 K)and pressure(0–30 GPa).Thermodynamically,the calculated mixing enthalpy and Gibbs free energy confirm the feasibility of forming a stable single-phase solid solution in(NbZrHfTi)C.The calculated results of the elastic stiffness constant indicate that the material meets the mechanical stability criteria of the cubic crystal system,further confirming the structural stability.Through evaluation of key mechanical parameters—bulk modulus,shear modulus,Young’s modulus,and Poisson’s ratio—we provide comprehensive insight into the macro-mechanical behaviour of the material and its correlation with the underlying microstructure.Notably,compared to traditional binary carbides and their average properties,(NbZrHfTi)C exhibits higher Vickers hardness(Approximately 28.5 GPa)and fracture toughness(Approximately 3.4 MPa⋅m^(1/2)),which can be primarily attributed to the lattice distortion and solid-solution strengthening mechanism.The study also utilizes the quasi-harmonic approximation method to predict the material’s thermophysical properties,including Debye temperature(initial value around 563 K),thermal expansion coefficient(approximately 8.9×10^(−6) K−1 at 2000 K),and other key parameters such as heat capacity at constant volume.The results show that within the studied pressure and temperature ranges,(NbZrHfTi)C consistently maintains a stable phase structure and good thermomechanical properties.The thermal expansion coefficient increasing with temperature,while heat capacity approaches the Dulong-Petit limit at elevated temperatures.These findings underscore the potential of(NbZrHfTi)C applications in ultra-high temperature thermal protection systems,cutting tool coatings,and nuclear structural materials.展开更多
Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively invest...Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively investigated.Macroscopic morphology,microstructure,and interfacial structure of the joints were analyzed using scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer(XRD).The results show that magnetic pulse welding of dissimilar Mg/Fe metals is achieved using an Al interlayer,which acts as a bridge for deformation and diffusion.Specifically,the AZ31B/AA1060 interface exhibits a typical wavy morphology,and a transition zone exists at the joint interface,which may result in an extremely complex microstructure.The microstructure of this transition zone differs from that of AZ31B magnesium and 1060 Al alloys,and it is identified as brittle intermetallic compounds(IMCs)Al_(3)Mg_(2) and Al_(12)Mg_(17).The transition zone is mainly distributed on the Al side,with the maximum thickness of Al-side transition layer reaching approximately 13.53μm.Incomplete melting layers with varying thicknesses are observed at the primary weld interface,while micron-sized hole defects appear in the transition zone of the secondary weld interface.The AA1060/DC56D interface is mainly straight,with only a small number of discontinuous transition zones distributed intermittently along the interface.These transition zones are characterized by the presence of the brittle IMC FeAl_(3),with a maximum thickness of about 4μm.展开更多
SiO_(2)–CaO–Al_(2)O_(3)ternary inclusions are among the most common complex oxide inclusions in steel.Nevertheless,the chemical and physical properties of these composite inclusions,particularly with detailed compos...SiO_(2)–CaO–Al_(2)O_(3)ternary inclusions are among the most common complex oxide inclusions in steel.Nevertheless,the chemical and physical properties of these composite inclusions,particularly with detailed composition changes,have not been sufficiently investigated.In this study,first-principles density functional theory calculations were used to determine the electronic,mechanical,and thermodynamic properties of two stable phases in the SiO_(2)–CaO–Al_(2)O_(3)ternary inclusion system:anorthite(CaAl_(2)Si_(2)O_(8))and gehlenite(Ca_(2)Al_(2)SiO_(7)).Based on the electronic density of states analysis and band structure calculations,oxygen atoms play important roles in the electron reactivity of both phases.Young’s modulus and Poisson’s ratios were calculated and compared with those of the SiO_(2)–CaO inclusions.The Young’s moduli of CaAl_(2)Si_(2)O_(8)(101.32 GPa)and Ca_(2)Al_(2)SiO_(7)(131.43 GPa)were close to the maximum and minimum Young’s moduli of the binary oxide inclusions,respectively.With increasing temperature,the Young’s moduli of CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)showed slight increasing and decreasing trends,respectively,whereas the Poisson’s ratio decreased.Furthermore,the thermodynamic properties,particularly temperature-related thermal expansion coefficients,were also deeply investigated.The thermal expansion coefficients of both CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)increased rapidly with increasing temperature in the low-temperature regime above 300K.As the temperature increased,the increasing trend slowed.When the temperature reached 2000 K,the thermal expansion coefficients of CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)respectively were 12×10^(−6)and 8.5×10^(−6)K^(−1).These findings enhance the understanding of the physical nature of ternary inclusions in steels and provide a scientific foundation for analyzing their effects on steel performance using a more comprehensive inclusion database,thereby contributing to inclusion engineering in the development of materials with superior mechanical integrity.展开更多
Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the eff...Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the effects of strengthening phases on Cu,Cu-carbon nanotubes(CNTs)composites were prepared using LPBF technique with Cu-CNTs mixed powder as the matrix.The formability,microstructure,mechanical properties,electrical conductivity,and thermal properties were studied.The result shows that the prepared composites have high relative density.The addition of CNTs results in inhomogeneous equiaxed grains at the edges of the molten pool and columnar grains at the center.Compared with pure copper,the overall mechanical properties of the composite are improved:tensile strength increases by 52.8%and elongation increases by 146.4%;the electrical and thermal properties are also enhanced:thermal conductivity increases by 10.8%and electrical conductivity increases by 12.7%.展开更多
To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agric...To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agricultural Experimental Station of Chinese Academy Sciences in the Low Plain of the North China Plain,comprising four irrigation treatments:irrigation once at the jointing stage for winter wheat with irrigation water containing salt at fresh water,3,4 and 5 g·L^(–1),and maize irrigation at sowing using fresh water.Manure application was conducted under all irrigation treatments,with treatments without manure application used as controls.The results showed that under long-term irrigation with saline water,the application of manure increased the soil organic matter content,exchangeable potassium,available phosphorus,and total nitrogen content in the 0–20 cm soil layer by 46.8%,117.0%,75.7%,and 45.5%,respectively,compared to treatments without manure application.The application of manure reduced soil bulk density.It also increased the proportion of water-stable aggregates and the abundance of bacteria,fungi,and actinomycetes in the tillage soil layer compared to the controls.Because of the salt contained in the manure,the application of manure had dual effects on soil salt content.During the winter wheat season,manure application increased soil salt content.The salt content was significantly reduced during the summer maize season,owing to the strong salt-leaching effects under manure application,resulting in a smaller difference in salt content between the manure and non-manure treatments.During the summer rainfall season,improvements in soil structure under manure application increased the soil desalination rate for the 1 m top soil layer.The desalination rate for 0–40 cm and 40–100 cm was averagely by 39.1%and 18.9%higher,respectively,under manure application as compared with that under the nomanure treatments.The yield of winter wheat under manure application was 0.12%lower than that of the control,owing to the higher salt content during the winter wheat season.In contrast,the yield of summer maize improved by 3.9%under manure application,owing to the increased soil nutrient content and effective salt leaching.The results of this study indicated that manure application helped maintain the soil physical structure,which is important for the long-term use of saline water.In practice,using manure with a low salt content is suggested to reduce the adverse effects of saline water irrigation on soil properties and achieve sustainable saline water use.展开更多
Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely us...Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely used in fields such as injection molding,die casting,and stamping dies.Adding reinforcing particles into steel is an effective means to improve its performance.Nb/18Ni300 composites were fabricated by LPBF using two kinds of Nb powders with different particle sizes,and their microstructures and properties were studied.The results show that the unmelted Nb particles are uniformly distributed in the 18Ni300 matrix and the grains are refined,which is particularly pronounced with fine Nb particles.In addition,element diffusion occurs between the particles and the matrix.The main phases of the base alloy are α-Fe and a small amount of γ-Fe.With the addition of Nb,part of the α-Fe is transformed into γ-Fe,and unmelted Nb phases appear.The addition of Nb also enhances the hardness and wear resistance of the composites but slightly reduces their tensile properties.After aging treatment,the molten pools and grain boundaries become blurred,grains are further refined,and the interfaces around the particles are thinned.The aging treatment also promotes the formation of reverted austenite.The hardness,ultimate tensile strength,and volumetric wear rate of the base alloy reach 51.9 HRC,1704 MPa,and 17.8×10^(-6) mm^(3)/(N·m),respectively.In contrast,the sample added with fine Nb particles has the highest hardness(56.1 HRC),ultimate tensile strength(1892 MPa)and yield strength(1842 MPa),and the volume wear rate of the sample added with coarse Nb particles is reduced by 90%to 1.7×10^(-6) mm^(3)/(N·m).展开更多
基金financially supported by the National Natural Science Foundation of China(No.60961001)the National Natural Science Foundation of China and China Academy of Engineering Physics Joint Funds(No.11076016)the AdvanceResearch of National Basic Research Program of China(No. 2010CB635112)
文摘Composite films of different contents were prepared by Fe73.5Cu1Nb3Si13.5B9 powder as compound phase and silicone rubber as matrix phase. The thickness of film is 200 μm. Values of impedance, Z, under pressure stress were measured by TH2816LCR digital bridge. LYYL-500N high-grade-type microcomputer control pressure testing machine was used to conduct program control loading with a speed of 0.1 mm·min^-1. The results show that composite films of different contents （25 vol%, 30 vol%, and 35 vol%） have excellent force-sensitive properties in both loading process and unloading process, especially when the stress is below 0.2 MPa, the stress- impedance （SI） and ＋｜k｜ values of composite films are much higher than that in the range of 0.2-1.0 MPa. The force- sensitive properties of loading process are superior to unloading process. While the frequency is 1 kHz, the force-sensitive properties of composite films are better than 50 kHz. The optimal temperature of powder heat treatment is 500 ℃. Composite film which was prepared by this kind of powder has a good force-sensitive property.
基金supported by the National Natural Science Foundation of China (No.82174074)。
文摘This study investigates the properties of high-purity starches extracted from Polygonum multiflorum(PMS)and Smilax glabra(SGS).The starches were characterized by scanning electron microscopy,Fouriertransform infrared spectroscopy,X-ray diffraction,high-performance anion-exchange chromatography,and differential scanning calorimetry.Significant differences were observed in their morphological,physicochemical,and functional properties.PMS had a smaller particle size(13.68 μm),irregular polygonal shape,A-type,lower water absorption(62.67 %),and higher oil absorption(51.17 %).In contrast,SGS exhibited larger particles(31.75 μm),a nearly spherical shape,B-type,higher crystallinity(50.66 %),and greater amylose content(21.54 %),with superior thermal stability,shear resistance,and gelatinization enthalpy.SGS also contained higher resistant starch(83.28 %) and longer average chain length(20.58 %),but showed lower solubility,swelling power,light transmittance,and freeze-thaw stability.The physicochemical properties differences in crystal pattern and particle morphology between PMS and SGS lead to distinct behaviors during in vitro digestion and fermentation.These findings highlight the potential of medicinal plant starches in functional ingredients and industrial processes.
文摘Herein,antibacterial silver‑doped fluorescent carbon dots(Ag‑CDs)were synthesized through a stepwise hydrothermal method,with polyethyleneimine(PEI),citric acid(CA),and silver nitrate(AgNO3)serving as precursors.The applicability and antimicrobial efficacy of these nanomaterials were systematically investigated for metal ion sensing.Experimental evidence demonstrated that the Ag‑CDs exhibited a pronounced fluorescence quenching response toward ferric ions(Fe^(3+)),enabling their quantitative determination via a linear concentration‑dependent relationship.These Ag‑CDs exhibited significant inhibitory effects on biofilm growth and disruption for both Escherichia coli and Staphylococcus aureus.Mechanism investigations indicate that Ag‑CDs induced the death of Escherichia coli and Pseudomonas aeruginosa by disrupting their bacterial morphology and structure,triggering the generation of intracellular reactive oxygen species(ROS),and impairing their antioxidant defense system.
基金Supported by National Natural Science Foundation of China(50976032,51776070)。
文摘Oxygen carriers play a fundamental role in chemical looping combustion(CLC).Iron-based carriers have been extensively investigated owing to their abundance and environmentally friendly.However,the reactivity and separability of iron-based carriers require further enhancement.This study investigates the effect of the concentration of Mn doping on reactivity,elastic properties and magnetic properties based on density functional theory(DFT)calculations.Theoretical results demonstrate that Mn doping effectively enhances reactivity by reducing the oxygen vacancy formation energy(E_(vac))from 2.33 to 0.87 eV.However,Mn doping introduces HV/EV Ms lattice distortions that deteriorate elastic properties,thereby reducing wear resistance,as evidenced by a 54.54%decrease in the hardness-to-Young's modulus ratio(H_(v)/E_(v))forα-Fe_(2)O_(3)and an 83.33%reduction for Fe_(3)O_(4).Furthermore,Mn doping also modifies magnetic properties.The maximum of saturation magnetization(M_(s))of Fe_(3)O_(4)reaches 121.02 emu/g at 33.33%Mn doping concentration.Finally,systematic evaluation identifies 33.33%as the optimal Mn doping concentration,achieving a balance in enhanced reactivity,superior magnetic performance,and retained elastic stability.
基金Tianjin Municipal Natural Science Foundation(23JCYBJC00040)National Natural Science Foundation of China(52175369)。
文摘The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.
文摘Six new lanthanide complexes:[Ln(3,4-DEOBA)3(4,4'-DM-2,2'-bipy)]2·2C_(2)H_(5)OH,[Ln=Dy(1),Eu(2),Tb(3),Sm(4),Ho(5),Gd(6);3,4-DEOBA-=3,4-diethoxybenzoate,4,4'-DM-2,2'-bipy=4,4'-dimethyl-2,2'-bipyridine]were successfully synthesized by the volatilization of the solution at room temperature.The crystal structures of six complexes were determined by single-crystal X-ray diffraction technology.The results showed that the complexes all have a binuclear structure,and the structures contain free ethanol molecules.Moreover,the coordination number of the central metal of each structural unit is eight.Adjacent structural units interact with each other through hydrogen bonds and further expand to form 1D chain-like and 2D planar structures.After conducting a systematic study on the luminescence properties of complexes 1-4,their emission and excitation spectra were obtained.Experimental results indicated that the fluorescence lifetimes of complexes 2 and 3 were 0.807 and 0.845 ms,respectively.The emission spectral data of complexes 1-4 were imported into the CIE chromaticity coordinate system,and their corre sponding luminescent regions cover the yellow light,red light,green light,and orange-red light bands,respectively.Within the temperature range of 299.15-1300 K,the thermal decomposition processes of the six complexes were comprehensively analyzed by using TG-DSC/FTIR/MS technology.The hypothesis of the gradual loss of ligand groups during the decomposition process was verified by detecting the escaped gas,3D infrared spectroscopy,and ion fragment information detected by mass spectrometry.The specific decomposition path is as follows:firstly,free ethanol molecules and neutral ligands are removed,and finally,acidic ligands are released;the final product is the corresponding metal oxide.CCDC:2430420,1;2430422,2;2430419,3;2430424,4;2430421,5;2430423,6.
文摘The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance Young's modulus measurements,and microstructure analysis,the effects of dislocation density,vacancy formation,and recrystallization on the alloy performance were clarified.Results indicate that increasing the rolling reduction enhances damping property due to higher dislocation density,whereas aging below the recrystallization temperature reduces damping property via dislocation pinning by the Suzuki effect.Recrystallization heat treatment restores the original structure and damping level.This alloy possesses tensile strength of approximately 1500 MPa and logarithmic decrement valueδ^(-1) in the range of 2×10^(-4)–3×10^(-4),demonstrating superior mechanical properties compared with the Ti-based alloys,which makes it an excellent candidate material for ultrasonic tools and medical applications.
文摘The ionothermal reaction between CuCl_(2),1,4-bis(1,2,4-triazol-1-ylmethyl)benzene(BBTZ),and(NH_(4))_(6)Mo_(7)O_(24) in 1-ethyl-3-methylimidazolium bromide((Emim)Br)led to a new octamolybdate-based coordination polymer(Emim)2[Cu(BBTZ)_(2)(β-Mo_(8)O_(26))](Mo_(8)-CP).Mo_(8)-CP was characterized by elemental analysis,thermogravime-try,IR,powder X-ray diffraction,and single-crystal X-ray diffraction.In Mo_(8)-CP,structural analysis reveals that Cu coordinates with BBTZ ligands to form an interlocked 1D chain.These chains are further bridged by(β-Mo_(8)O_(26))^(4-)to construct a 3D coordination polymer.Notably,(Emim)^(+)acts as a structure-directing agent,occupying the channels of the 3D coordination polymer.Based on this unique structure,the ion exchange properties of Mo_(8)-CP toward rare-earth ions were investigated.It has been found that the luminescent color of the material can be successfully regulat-ed by introducing Eu^(3+)or Tb^(3+)through ion exchange.CCDC:2475110,Mo_(8)-CP.
基金National Natural Science Foundation of China(51774179)Natural Science Foundation of Liaoning Province(20180550546)+2 种基金Joint Fund of State Key Laboratory of Metal Material for Marine Equipment and Application(HGSKL-USTLN(2021)03)High-Level Talent Fund of USTL(6003000377,6003000294)supported by Liaoning Provincial Department of Education(LJ212410146037)。
文摘The effect of element Ti on the microstructures and mechanical properties of as-cast and annealed NbTaMoWTi,(x=0,1,1.5,2)refractory high-entropy alloys(RHEAs)was investigated.Results show that after Ti addition,the as-cast alloys maintain their original single body-centered cubic(bcc)structure.As for the mechanical properties,compared with those without Ti addition,the strength and ductility of NbTaMoWTi,alloys increase by 93%and 215%,respectively.Furthermore,the NbTaMoWTi alloys exhibit outstanding thermal stability.After annealing at 1400 C,they still maintain the single bcc structure,and their mechanical properties are even slightly improved.However,annealing leads to a significant deterioration in the mechanical properties of high-Ti-content alloys(NbTaMoWTil and NbTaMoWTi2),owing to the formation of Ti-rich acicular phases.
基金National Natural Science Foundation of China(U24A2038)。
文摘The effects of channel segregation on the macro-and micro-scale chemical composition,microstructure,hardness,and tensile deformation behavior of Ti45Nb wires were investigated.The results show that wires with severe channel segregation exhibit a macroscopic chemical composition identical to those without segregation,and 3D X-ray imaging result also reveals no abnormalities.After annealing,both types of wires exhibit an equiaxed single-phase microstructure with comparable grain sizes,suggesting that channel segregation has negligible influence on the macroscopic composition and grain size.Metallographic examination reveals that channel segregation manifests as spot-like features in the transverse section and band-like structures in the longitudinal section.EDS analysis identifies these regions as Ti-enriched segregations,with a Ti content higher than that of the surrounding matrix by approximately 4.42wt%.Compared to segregation-free wires,those containing extensive channel segregation demonstrate a 15.5%increase in ultimate tensile strength and a 12.3%increase in yield strength,but suffer a reduction in elongation and reduction of area by 19.8%and 18.9%,respectively.Furthermore,the mechanical properties of wires with segregation show significant fluctuations.Fractographic analysis reveals a larger fracture surface area in segregated wires.Severe dislocation pile-ups occur at the interfaces of these segregated regions,initiating microcrack nucleation.This promotes rapid crack propagation of the Ti45Nb wire,leading to a significant decrease in plasticity and reduction of area.
基金National Natural Science Foundation of China(52172108)National Key R&D Program of China(2022YFB3707700)Strategic Priority Research Program of the Chinese Academy of Sciences(XDC0144005)。
文摘Silicon carbide fibers are considered ideal reinforcing materials for ceramic matrix composites due to their excellent mechanical properties and high-temperature performance.Different types of fibers necessitate individual investigation due to variations in their composition and fabrication processes.This study presents a comprehensive investigation into evolution of the mechanical properties,surface microstructure,and composition of Shicolon-Ⅱ fibers subjected to argon heat treatment at temperatures ranging from 1300℃to 1700℃.The Shicolon-Ⅱ fibers are composed of small-sized β-SiC grains,SiC_(x)O_(y) amorphous phase,and a minor amount of graphite microcrystals.Following treatment in an argon atmosphere at 1300℃,the fibers maintain a monofilament tensile strength of 3.620 GPa,corresponding to a retention of 98.32%.This strength diminishes to 2.875 GPa,equating to a retention of 78.08%,after treatment at 1500℃.The reduction in mechanical properties of the fibers can be ascribed to the decomposition of the amorphous phase and the growth of β-SiC grains.Furthermore,creep resistance is an essential factor influencing the long-term performance of composite materials.After treatment at temperatures above 1400℃,the high-temperature creep resistance of the fibers is significantly enhanced due to growth of β-SiC grains.This study offers valuable theoretical insights into high-temperature applications of second-generation fibers,contributing to an enhanced understanding of their performance under extreme conditions.
文摘Three zinc(Ⅱ),nickel(Ⅱ),and cadmium(Ⅱ)complexes,namely[Zn(μ-Htpta)(py)_(2)]n(1),[Ni(H_(2)biim)2(H_(2)O)2][Ni(tpta)(H_(2)biim)2(H_(2)O)]2·3H_(2)O(2),and[Cd_(3)(μ4-tpta)2(μ-dpe)_(3)]_(n)(3),have been constructed hydrothermally at 160℃ using H_(3)tpta([1,1':3',1″-terphenyl]-4,4',5'-tricarboxylic acid),py(pyridine),H_(2)biim(2,2'-biimidazole),dpe(1,2-di(4-pyridyl)ethylene),and zinc,nickel and cadmium chlorides,resulting in the formation of stable crystalline solids which were subsequently analyzed using infrared spectroscopy,element analysis,thermogravimetric analysis,as well as structural analyses conducted via single-crystal X-ray diffraction.The findings from these single-crystal Xray diffraction studies indicate that complexes 1-3 form crystals within the monoclinic system P2_(1)/c space group(1)or triclinic system P1 space group(2 and 3),and possess 1D,0D,and 3D structures,respectively.Complex 1 demonstrated substantial catalytic efficiency and excellent reusability as a heterogeneous catalyst in the reaction of Knoevenagel condensation under ambient temperature conditions.In addition,complex 1 also showcased notable anti-wear performance when used in polyalphaolefin synthetic lubricants.CCDC:2449810,1;2449811,2;2449812,3.
基金supported by the National Natural Science Foundation of China(Nos.92166105 and 52005053)High-Tech Industry Science and Technology Innovation Leading Program of Hunan Province(No.2020GK2085)the Science and Technology Innovation Program of Hunan Province(No.2021RC3096).
文摘(NbZrHfTi)C high-entropy ceramics,as an emerging class of ultra-high-temperature materials,have garnered significant interest due to their unique multi-principal-element crystal structure and exceptional hightemperature properties.This study systematically investigates the mechanical properties of(NbZrHfTi)C high-entropy ceramics by employing first-principles density functional theory,combined with the Debye-Grüneisen model,to explore the variations in their thermophysical properties with temperature(0–2000 K)and pressure(0–30 GPa).Thermodynamically,the calculated mixing enthalpy and Gibbs free energy confirm the feasibility of forming a stable single-phase solid solution in(NbZrHfTi)C.The calculated results of the elastic stiffness constant indicate that the material meets the mechanical stability criteria of the cubic crystal system,further confirming the structural stability.Through evaluation of key mechanical parameters—bulk modulus,shear modulus,Young’s modulus,and Poisson’s ratio—we provide comprehensive insight into the macro-mechanical behaviour of the material and its correlation with the underlying microstructure.Notably,compared to traditional binary carbides and their average properties,(NbZrHfTi)C exhibits higher Vickers hardness(Approximately 28.5 GPa)and fracture toughness(Approximately 3.4 MPa⋅m^(1/2)),which can be primarily attributed to the lattice distortion and solid-solution strengthening mechanism.The study also utilizes the quasi-harmonic approximation method to predict the material’s thermophysical properties,including Debye temperature(initial value around 563 K),thermal expansion coefficient(approximately 8.9×10^(−6) K−1 at 2000 K),and other key parameters such as heat capacity at constant volume.The results show that within the studied pressure and temperature ranges,(NbZrHfTi)C consistently maintains a stable phase structure and good thermomechanical properties.The thermal expansion coefficient increasing with temperature,while heat capacity approaches the Dulong-Petit limit at elevated temperatures.These findings underscore the potential of(NbZrHfTi)C applications in ultra-high temperature thermal protection systems,cutting tool coatings,and nuclear structural materials.
文摘Dissimilar AZ31B magnesium alloy and DC56D steel were welded via AA1060 aluminum alloy by magnetic pulse welding.The effects of primary and secondary welding processes on the welded interface were comparatively investigated.Macroscopic morphology,microstructure,and interfacial structure of the joints were analyzed using scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer(XRD).The results show that magnetic pulse welding of dissimilar Mg/Fe metals is achieved using an Al interlayer,which acts as a bridge for deformation and diffusion.Specifically,the AZ31B/AA1060 interface exhibits a typical wavy morphology,and a transition zone exists at the joint interface,which may result in an extremely complex microstructure.The microstructure of this transition zone differs from that of AZ31B magnesium and 1060 Al alloys,and it is identified as brittle intermetallic compounds(IMCs)Al_(3)Mg_(2) and Al_(12)Mg_(17).The transition zone is mainly distributed on the Al side,with the maximum thickness of Al-side transition layer reaching approximately 13.53μm.Incomplete melting layers with varying thicknesses are observed at the primary weld interface,while micron-sized hole defects appear in the transition zone of the secondary weld interface.The AA1060/DC56D interface is mainly straight,with only a small number of discontinuous transition zones distributed intermittently along the interface.These transition zones are characterized by the presence of the brittle IMC FeAl_(3),with a maximum thickness of about 4μm.
基金financially supported by the National Nat-ural Science Foundation of China(No.52404337)the Chun-hui Plan Collaborative Research Project from Chinese Edu-cation Ministry(No.HZKY20220036)+1 种基金the Guangdong Ba-sic and Applied Basic Research Foundation,China(No.2022A1515110062)the Young Elite Scientists Spon-sorship Program by China Association for Science and Tech-nology(No.YESS20220231).
文摘SiO_(2)–CaO–Al_(2)O_(3)ternary inclusions are among the most common complex oxide inclusions in steel.Nevertheless,the chemical and physical properties of these composite inclusions,particularly with detailed composition changes,have not been sufficiently investigated.In this study,first-principles density functional theory calculations were used to determine the electronic,mechanical,and thermodynamic properties of two stable phases in the SiO_(2)–CaO–Al_(2)O_(3)ternary inclusion system:anorthite(CaAl_(2)Si_(2)O_(8))and gehlenite(Ca_(2)Al_(2)SiO_(7)).Based on the electronic density of states analysis and band structure calculations,oxygen atoms play important roles in the electron reactivity of both phases.Young’s modulus and Poisson’s ratios were calculated and compared with those of the SiO_(2)–CaO inclusions.The Young’s moduli of CaAl_(2)Si_(2)O_(8)(101.32 GPa)and Ca_(2)Al_(2)SiO_(7)(131.43 GPa)were close to the maximum and minimum Young’s moduli of the binary oxide inclusions,respectively.With increasing temperature,the Young’s moduli of CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)showed slight increasing and decreasing trends,respectively,whereas the Poisson’s ratio decreased.Furthermore,the thermodynamic properties,particularly temperature-related thermal expansion coefficients,were also deeply investigated.The thermal expansion coefficients of both CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)increased rapidly with increasing temperature in the low-temperature regime above 300K.As the temperature increased,the increasing trend slowed.When the temperature reached 2000 K,the thermal expansion coefficients of CaAl_(2)Si_(2)O_(8)and Ca_(2)Al_(2)SiO_(7)respectively were 12×10^(−6)and 8.5×10^(−6)K^(−1).These findings enhance the understanding of the physical nature of ternary inclusions in steels and provide a scientific foundation for analyzing their effects on steel performance using a more comprehensive inclusion database,thereby contributing to inclusion engineering in the development of materials with superior mechanical integrity.
基金National Key Research and Development Program of China(2023YFB4606400)Supported by Longmen Laboratory Frontier Exploration Topics(LMQYTSKT003)。
文摘Copper manufactured by laser powder bed fusion(LPBF)process typically exhibits poor strength-ductility coordination,and the addition of strengthening phases is an effective way to address this issue.To explore the effects of strengthening phases on Cu,Cu-carbon nanotubes(CNTs)composites were prepared using LPBF technique with Cu-CNTs mixed powder as the matrix.The formability,microstructure,mechanical properties,electrical conductivity,and thermal properties were studied.The result shows that the prepared composites have high relative density.The addition of CNTs results in inhomogeneous equiaxed grains at the edges of the molten pool and columnar grains at the center.Compared with pure copper,the overall mechanical properties of the composite are improved:tensile strength increases by 52.8%and elongation increases by 146.4%;the electrical and thermal properties are also enhanced:thermal conductivity increases by 10.8%and electrical conductivity increases by 12.7%.
基金supported by National Key R&D Program of China (2022YFD1900104)。
文摘To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agricultural Experimental Station of Chinese Academy Sciences in the Low Plain of the North China Plain,comprising four irrigation treatments:irrigation once at the jointing stage for winter wheat with irrigation water containing salt at fresh water,3,4 and 5 g·L^(–1),and maize irrigation at sowing using fresh water.Manure application was conducted under all irrigation treatments,with treatments without manure application used as controls.The results showed that under long-term irrigation with saline water,the application of manure increased the soil organic matter content,exchangeable potassium,available phosphorus,and total nitrogen content in the 0–20 cm soil layer by 46.8%,117.0%,75.7%,and 45.5%,respectively,compared to treatments without manure application.The application of manure reduced soil bulk density.It also increased the proportion of water-stable aggregates and the abundance of bacteria,fungi,and actinomycetes in the tillage soil layer compared to the controls.Because of the salt contained in the manure,the application of manure had dual effects on soil salt content.During the winter wheat season,manure application increased soil salt content.The salt content was significantly reduced during the summer maize season,owing to the strong salt-leaching effects under manure application,resulting in a smaller difference in salt content between the manure and non-manure treatments.During the summer rainfall season,improvements in soil structure under manure application increased the soil desalination rate for the 1 m top soil layer.The desalination rate for 0–40 cm and 40–100 cm was averagely by 39.1%and 18.9%higher,respectively,under manure application as compared with that under the nomanure treatments.The yield of winter wheat under manure application was 0.12%lower than that of the control,owing to the higher salt content during the winter wheat season.In contrast,the yield of summer maize improved by 3.9%under manure application,owing to the increased soil nutrient content and effective salt leaching.The results of this study indicated that manure application helped maintain the soil physical structure,which is important for the long-term use of saline water.In practice,using manure with a low salt content is suggested to reduce the adverse effects of saline water irrigation on soil properties and achieve sustainable saline water use.
基金Key-Area Research and Development Program of Guangdong Province(2023B0909020004)Project of Innovation Research Team in Zhongshan(CXTD2023006)+1 种基金Natural Science Foundation of Guangdong Province(2023A1515011573)Zhongshan Social Welfare Science and Technology Research Project(2024B2022)。
文摘Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely used in fields such as injection molding,die casting,and stamping dies.Adding reinforcing particles into steel is an effective means to improve its performance.Nb/18Ni300 composites were fabricated by LPBF using two kinds of Nb powders with different particle sizes,and their microstructures and properties were studied.The results show that the unmelted Nb particles are uniformly distributed in the 18Ni300 matrix and the grains are refined,which is particularly pronounced with fine Nb particles.In addition,element diffusion occurs between the particles and the matrix.The main phases of the base alloy are α-Fe and a small amount of γ-Fe.With the addition of Nb,part of the α-Fe is transformed into γ-Fe,and unmelted Nb phases appear.The addition of Nb also enhances the hardness and wear resistance of the composites but slightly reduces their tensile properties.After aging treatment,the molten pools and grain boundaries become blurred,grains are further refined,and the interfaces around the particles are thinned.The aging treatment also promotes the formation of reverted austenite.The hardness,ultimate tensile strength,and volumetric wear rate of the base alloy reach 51.9 HRC,1704 MPa,and 17.8×10^(-6) mm^(3)/(N·m),respectively.In contrast,the sample added with fine Nb particles has the highest hardness(56.1 HRC),ultimate tensile strength(1892 MPa)and yield strength(1842 MPa),and the volume wear rate of the sample added with coarse Nb particles is reduced by 90%to 1.7×10^(-6) mm^(3)/(N·m).
