It is crucial to develop arsenic removal adsorbents with strong sulfur resistance under middle-low-temperature flue gas conditions(<400℃).In this work,five Fe-Ce-La oxides were prepared by co-precipitation method,...It is crucial to develop arsenic removal adsorbents with strong sulfur resistance under middle-low-temperature flue gas conditions(<400℃).In this work,five Fe-Ce-La oxides were prepared by co-precipitation method,and FeCeLaO/SiO_(2)-Al_(2)O_(3) composite adsorbents were prepared by coupling fly ash-based Si-Al carriers.The active components Fe-Ce-La oxides and Si-Al carriers were characterized by TPD,TG,XRF,BET and XPS,respectively.The effects of temperature,Si/Al ratio and FeCeLaO loading rate on the sulfur resistance were investigated.Results show that the SO_(2) promotes the arsenic removal of Fe_(2)O_(3),CeLaO and FeCeLaO.At 400℃,the arsenic removal efficiencies of the three oxides increase from 45.3%,72.5% and 81.3% without SO_(2) to 62.6%,80.5%and 91.0%,respectively.The SO_(2) inhibits the arsenic removal of La_(2)O_(2)CO_(3) and FeLaO,and the inhibition effect is pronounced at high temperatures.The sulfur poisoning resistance of Si-Al carriers increases with the increase of Si/Al ratio.When the Si/Al ratio is increased to 9.74,the arsenic removal efficiency in the SO_(2) environment is 13.9% higher than that in the absence of SO_(2).Introducing FeCeLaO active components is beneficial for enhancing the SO_(2) poisoning resistance of Si-Al carriers.The strong sulfur resistance of the FeCeLaO/SiO_(2)-Al_(2)O_(3) composite adsorbent results from multiple factors:protective effects of Ce on Fe,La and Al;sulfation-induced generation of Ce^(3+)and surface-adsorbed oxygen;and strong surface acidity of SiO_(2).展开更多
Surfaces of grade III fly ashes were modified through mixing with carbide slag and calcining at 850 ℃ for 1 h. Mineralogical compositions and surface morphology of fly ashes before and after modification were charact...Surfaces of grade III fly ashes were modified through mixing with carbide slag and calcining at 850 ℃ for 1 h. Mineralogical compositions and surface morphology of fly ashes before and after modification were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）, respectively. Effect of surface-modified fly ashes on compressive strength and autogenous shrinkage of blended cement pastes was investigated. Microstructures of cement pastes were examined by backscattered electron （BSE） imaging and mercury intrusion porosimetry （MIP）. The experimental results showed that β-C2S was formed on the surfaces of fly ashes after modification. Hydration ofβ-C2S on the surface-modified fly ashes densified interface zone and enhanced bond strength between particles of fly ashes and hydrated clinkers. In addition, surface modification of fly ashes tended to decrease total porosity and 10-50 nm pores of cement pastes. Surface modification of fly ashes increased compressive strength and reduced autogenous shrinkage of cement pastes.展开更多
Valuable metal extraction technology from thermal power plant fly ash is limited.In the present study,aluminium is extracted from fly ash as highly pure aluminium sulphate(>99.0%)by leaching with sulphuric acid,fol...Valuable metal extraction technology from thermal power plant fly ash is limited.In the present study,aluminium is extracted from fly ash as highly pure aluminium sulphate(>99.0%)by leaching with sulphuric acid,followed by pre-concentration and successive crystallization.Two types of fly ashes from different sources,i.e.,Talcher Thermal Power Station(TTPS)and Vedanta Aluminium Company Limited(VAL)were chosen for comparative study on the extraction of aluminium as aluminium sulphate.The product is characterized by powder X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR)and thermogravimetric analysis(TGA).Purity of aluminium sulphate was also investigated by inductively coupled plasma?optical emission spectrometry(ICP?OES).The extraction efficiency of aluminium depends on the varied solid-to-liquid ratio(fly ash:18mol/L H2SO4,g/mL)and particle size of fly ashes.Physico-chemical analysis indicates that the obtained product is Al2(SO4)3·18H2O,having low iron content(0.08%).展开更多
Ferrospheres in fly ashes from a coal-fired power plant were extracted by a magnetic separation technique and their microstructure was studied by scanning electron microscopy (SEM), energy dispersive X-ray analysis (E...Ferrospheres in fly ashes from a coal-fired power plant were extracted by a magnetic separation technique and their microstructure was studied by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and environmental scanning electron microscopy (ESEM). Ferrospheres in fly ashes show significant iron enrichment compared to their respective fly ashes. Iron oxides in ferrospheres mainly occur as minerals magnetite (Fe3O4) and hematite (α-Fe2O3), which are derived mainly from the decomposition and oxidation of iron-bearing minerals in coal during combustion. EDX data indicate that ferrospheres also contain Si, S, Al and Ca resulting from quartz, mullite, anhydrite and amorphous materials. A large percentage of ferrospheres are commonly 5～50 μm in size. The microstructure of ferrospheres includes smooth, polygonal, dendritic, granular and molten drop characteristics. SEM coupled with EDX provided fast and accurate results of the microstructure and chemical composition of ferrospheres, and helped us to assess environmental issues related to the disposal and utilization of fly ashes.展开更多
The Yanzhou mine district, located in southwestern Shandong Province, is about 1300 km2 with more than 8×109tons of proved coal reserves and there are 10 big power plants in this area. A large amount of coal ashe...The Yanzhou mine district, located in southwestern Shandong Province, is about 1300 km2 with more than 8×109tons of proved coal reserves and there are 10 big power plants in this area. A large amount of coal ashes, which are regarded as waste materials, have been stockpiled in the area and have influenced the environment of the mine district. In this paper, analysis of fly ash samples from three power plants is carried out, the enrichment and concentration of trace elements, Pb, Zn, Cu and As, in coal ashes are analyzed, and petrological and mineralogical characteristics and chemical compositions of coal ashes are studied. The aim of this work is to provide basic scientific data for utilization of ashes and reduction of environmental pollutions.展开更多
For the handling, treatment and utilization of fly ash from biomass combustion its chemical composition and physical properties are important. In this study eight filter fly ashes from different grate-fired biomass co...For the handling, treatment and utilization of fly ash from biomass combustion its chemical composition and physical properties are important. In this study eight filter fly ashes from different grate-fired biomass combustion plants were investigated. In fly ash from straw combustion high concentrations of（K） were found, whereas in the fly ash from wood combustion the concentrations of Ca and Mg were higher. The average concentration of PO3-4was similar in both types of fly ashes. In all wood fly ashes some measured heavy metal concentrations were above the limits for utilization. The straw fly ashes were much less contaminated and can be utilized. For wood fly ash most parameters showed little variation, except from one fly ash where the dust pre-separator is in poor condition. The average values were： mass median diameter 4.3 ± 0.8 μm, spread of particle size distribution19 ± 11, particle density 2620 ± 80 kg/m^3 and angle of repose 50°± 1°. The density of the straw fly ashes is lower（2260 ± 80 kg/m^3） and the spread of the size distribution is higher（72 ± 24）.For one straw combustion fly ash the values of the mass median diameter and the angle of repose were similar to the values of wood combustion fly ash, for the other straw fly ash the values differed considerably. While the particle size of this fly ash was much smaller,surprisingly the angle of repose was also lower. This can be attributed to the formation of small agglomerates in this fly ash, which were not disintegrated without a certain stress.展开更多
This paper presents the effect of fly ash grain-size fractions on Portland-fly ash cement hydration and its properties. Siliceous fly ashes of size fraction of 0 - 16 and 16 - 32 μm, separated from initial fly ash sa...This paper presents the effect of fly ash grain-size fractions on Portland-fly ash cement hydration and its properties. Siliceous fly ashes of size fraction of 0 - 16 and 16 - 32 μm, separated from initial fly ash samples from 1st, 2nd and 3rd hopper in ESP system, were analysed. Cement hydration was investigated by determination of hydration heat and content of Ca(OH)2 and C3S in cement samples. Water to cement ratio and initial setting time of cement pastes as well as compressive strength and microstructure of cement mortars were also analyzed. Results showed that the same amount of the same size ash fraction can give cement of lower or higher early strength and its lower or higher increase with time. Incorporation of 20 wt% of ash fraction of 0 - 16 μm can produce Portland-fly ash cement CEM II/A-V of strength class 42.5R (from 2nd hopper) or 52.5N (from 3rd hopper). Cement containing 40 wt% of ash fraction of 0 - 16 μm from 2nd and 3rd hopper can be classified as pozzolanic cements CEM IV/A-V of strength class 42.5 and normal or rapid early strength, respectively. Different development of strength of cement with addition of the same size ash fraction separated from the initial ash sample from the next hopper in ESP system is connected with higher depolymerization degree of SiO4 units in ash glass, resulting from the greater amount of AlO4 units replacing SiO4 units. Ash fraction of 16 - 32 μm shows lower depolymerisation of glass network and as a consequence lower hydration degree of C3S to portlandite and calcium silicate hydrates (C-S-H).展开更多
Three fresh China coals （lignitie, bituminite and anthracite） from different geological origin and the corresponding fly and bottom ashes were studied by room temperature（RT） Mossbauer spectroscopy（MS）. The iron...Three fresh China coals （lignitie, bituminite and anthracite） from different geological origin and the corresponding fly and bottom ashes were studied by room temperature（RT） Mossbauer spectroscopy（MS）. The iron-bearing minerals were characterized to be mainly pyrite in all coal samples by the hyperfine parameters.Suphate（FeSO4·nH2O） was found in bituminite and anthracite coal.The MSssbauer spectra of the fly and bottom ashes as a result of pulverised coal combustion（PCC） in Xiaolongtan,Shuicheng and Luohuang Power Plants are comprised of superimposed sextets and doulets of oxides includes maghemite（γ-Fe2O3）, magnitite（Fe3O4）, haematite（α-Fe2O3）, magnesioferite （MgFe2O4）, Fe^3＋/Fe^2＋ -mullite, Fe^3＋ -glass silicate and metallic iron. The studies also show that iron-bearing minerals in coals are largely dependant on geological regions and coal rank, the composition of the corresponding fly and bottom ashes will not only depend on the type and mineralogy of the feed coal but also on the local nature of combustion.展开更多
Recycling rare earth elements(REEs)from waste is necessary for an environmentally sustainable reuse and wastewater management approach.Na-A zeolite was synthesized from coal fly ash(CFA)and applied for Ce^(3+)adsorpti...Recycling rare earth elements(REEs)from waste is necessary for an environmentally sustainable reuse and wastewater management approach.Na-A zeolite was synthesized from coal fly ash(CFA)and applied for Ce^(3+)adsorption.Fourier transform infrared(FTIR)spectra show peaks at 790,500 and 467 cm^(-1),which are bond vibrations of Si-O-Si,Si with Al-O and Si-O-.The surface area is 15.88 m^(2)/g,with a pore size of 2.14 nm.SEM images show a cubic shape,which indicates the formation of zeolite.Field emission and energy disperse spectroscopy(EDS)shows the formation of Si,Al,Na,and O.Na-A zeolite was applied for Ce^(3+)adsorption.The optimum conditions for Ce^(3+)adsorption are 50 ppm concentration,360 min,and pH 6.The maximum adsorption capacity is 176.49 mg/g.Based on the results,it is found that the adsorption of Ce^(3+)by Na-A zeolite is pseudo-second-order.The desorption test using HNO_(3) is more effective than using HCl and H_(2)SO_(4).A desorption efficiency of 97.22%is obtained at 4 cycles.Adsorption test using real sample wastewater demonstrates an adsorption efficiency of 83.35%.展开更多
Three types of activators such as sodium hydroxide,calcium oxide and triethanolamine(TEA)are used to establish different activation environments to address the problems associated with the process of activating fly as...Three types of activators such as sodium hydroxide,calcium oxide and triethanolamine(TEA)are used to establish different activation environments to address the problems associated with the process of activating fly ash paste.We conducted mechanical tests and numerical simulations to understand the evolution of microstructure,and used environmental scanning electron microscopy(ESEM)and energy dispersive spectroscopy(EDS)techniques to analyze the microenvironments of the samples.The mechanical properties of fly ash paste under different activation conditions and the changes in the microstructure and composition were investigated.The results revealed that under conditions of low NaOH content(1%-3%),the strength of the sample increased significantly.When the content exceeded 4%,the rate of increase in strength decreased.Based on the results,the optimal NaOH content was identified,which was about 4%.A good activation effect,especially for short-term activation(3-7 d),was achieved using TEA under high doping conditions.The activation effect was poor for long-term strength after 28 days.The CaO content did not significantly affect the degree of activation achieved.The maximum effect was exerted when the content of CaO was 2%.The virtual cement and concrete testing laboratory(VCCTL)was used to simulate the hydration process,and the results revealed that the use of the three types of activators accelerated the formation of Ca(OH)_(2) in the system.The activators also corroded the surface of the fly ash particles,resulting in a pozzolanic reaction.The active substances in fly ash were released efficiently,and hydration was realized.The pores were filled with hydration products,and the microstructure changed to form a new frame of paste filling that helped improve the strength of fly ash paste.展开更多
In order to study the characteristics of pure fly ash-based geopolymer concrete(PFGC)conveniently,we used a machine learning method that can quantify the perception of characteristics to predict its compressive streng...In order to study the characteristics of pure fly ash-based geopolymer concrete(PFGC)conveniently,we used a machine learning method that can quantify the perception of characteristics to predict its compressive strength.In this study,505 groups of data were collected,and a new database of compressive strength of PFGC was constructed.In order to establish an accurate prediction model of compressive strength,five different types of machine learning networks were used for comparative analysis.The five machine learning models all showed good compressive strength prediction performance on PFGC.Among them,R2,MSE,RMSE and MAE of decision tree model(DT)are 0.99,1.58,1.25,and 0.25,respectively.While R2,MSE,RMSE and MAE of random forest model(RF)are 0.97,5.17,2.27 and 1.38,respectively.The two models have high prediction accuracy and outstanding generalization ability.In order to enhance the interpretability of model decision-making,we used importance ranking to obtain the perception of machine learning model to 13 variables.These 13 variables include chemical composition of fly ash(SiO_(2)/Al_(2)O_(3),Si/Al),the ratio of alkaline liquid to the binder,curing temperature,curing durations inside oven,fly ash dosage,fine aggregate dosage,coarse aggregate dosage,extra water dosage and sodium hydroxide dosage.Curing temperature,specimen ages and curing durations inside oven have the greatest influence on the prediction results,indicating that curing conditions have more prominent influence on the compressive strength of PFGC than ordinary Portland cement concrete.The importance of curing conditions of PFGC even exceeds that of the concrete mix proportion,due to the low reactivity of pure fly ash.展开更多
Microwave-curing and mechanical grinding of fly ash have both beenadopted as effective methods for improving the early-age strength of alkali-activated fly ash(AAFA)binders.This study combined these two approaches by ...Microwave-curing and mechanical grinding of fly ash have both beenadopted as effective methods for improving the early-age strength of alkali-activated fly ash(AAFA)binders.This study combined these two approaches by synthesizing AAFA using original,medium-fine,and ultrafine fly ash as precursors,and then specimens were cured with a five-stage temperature-controlled microwave.The compressive strength results indicate that the original AAFA develops the highest strength initially during microwave-curing,reaching 28 MPa at stage 2.Medium-fine AAFA exhibits the highest strength of 60 MPa when cured to stage 4-I,which is 26%higher than the peak strength of original AAFA.It is attributed to the significant rise in their specific surface area,which accelerates the dissolution of Si and Al from the precursor and facilitates the subsequent formation of N-A-S-H gels.Additionally,nanoscale zeolite crystals formed as secondary products fill the tiny gaps between amorphous products,thereby significantly improving their microstructure.In contrast,ultrafine fly ash,primarily composed of fragmented particles,necessitated a substantial amount of water,which adversely affects the absorption efficiency for microwave of AAFA specimens.Thus,ultrafine AAFA specimens consistently exhibit the lowest compressive strength.Specifically,at the end of curing,the compressive strength of these three specimens with microwave-curing is approximately 32%,59%,and 172%higher than that of the steam-cured sample,respectively.These findings demonstrate the compatibility of microwave-curing and fly ash refinement in enhancing the early compressive strength development of AAFA.展开更多
In order to adjust some properties of cement grout or concrete,some mineral admixtures are usually added in the preparation.Admixtures can reduce the cement consumption and save the cost,and also adjust the workabilit...In order to adjust some properties of cement grout or concrete,some mineral admixtures are usually added in the preparation.Admixtures can reduce the cement consumption and save the cost,and also adjust the workability of the material,improve the strength and durability of the cement stone,or reduce hydration heat of the composite cement.At present,the content of fly ash or slag is generally less than 50%among the composite cementitious materials that have been studied more,but there is little research on composite cementitious materials with large mineral admixture.In this paper,XRD,SEM,and adiabatic temperature rise tests were used to discuss hydration products and mechanism of composite cement grout with 90%content of fly ash and slag.The results show that the hydration of the composite cement grout is an alkali-activated hydration reaction,and the hydration products are mainly amorphous substances such as hydrated calcium silicate or hydrated calcium aluminate gel.The hydration reaction temperature rise is much lower than that of ordinary cement grout,and the time of the temperature peak is significantly delayed.展开更多
The present study investigates the engineering properties of submerged organic silt(orSi)stabilized with F-class fly ash(FA),with and without the addition of an activator(CaO).The utilization of F-class FA for soil im...The present study investigates the engineering properties of submerged organic silt(orSi)stabilized with F-class fly ash(FA),with and without the addition of an activator(CaO).The utilization of F-class FA for soil improvement is an important aspect of sustainable and environmentally-conscious geotechnical engineering when marginal usage of lime and concrete is of great interest to engineers and societies.Currently,discussion is predominantly focused on the positive aspects of using the F-class FA,with a paucity of emphasis on the negative aspects.To explore these features more thoroughly,a series of strength and compressibility tests was conducted.The sample preparation and curing methodology were chosen to replicate the in situ conditions where soil is surcharged and submerged in water.It was found that the incorporation of F-class FA without an activator reduces the undrained shear strength of submerged orSi by about 20%–25%and permanently prevents any thixotropic strength restoration.An increase in undrained shear strength is observed when lime(3%–6%)is added to the soil–FA mixture or when only lime(in the same amount of 3%–6%)is used.Consequently,F-class FA can be successfully used as a filler for slurries with minimum lime content in soil mixing methods.The F-class FA(with or without an activator)shifts the so-called“creep delay”in time,consequently reducing the total creep settlements.The shift of“creep delay”is more considerable for orSi stabilized with lime or with FA and lime as an activator,than for orSi stabilized with pure F-class FA.展开更多
This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, te...This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, terracotta brick seems to meet these needs. Thus, the objective of this work was to evaluate the influence of the incorporation of coal fly ash from a thermal power plant on the physical and mechanical properties of fired bricks from grey clay in the Thicky area of Senegal. The coal fly ash was incorporated into the raw clay material in proportions of 0, 5, 10, and 15 % by weight. These two raw materials were first characterized by X-ray fluorescence spectroscopy (XRF). The XRF analyses showed that the most abundant oxides in clay were SiO2 (55.034%) and Fe2O3 (10.155%). In coal fly ash, SiO2 (38.574%) is predominant. The ash also contained Al2O3 (7.717%) and alicano-earthy melting oxides such as CaO (9.271%) and MgO (7.298%) etc. These melting oxides were necessary to facilitate the formation of the liquid phase when baking platelets. The latter, when burned at a temperature of 880°C, were characterized by determining the number of physico-mechanical parameters, such as linear shrinkage during cooking, water absorption, fire loss and compressive strength. A Hierarchical Ascending Classification of these different parameters was performed and three classes were obtained. Class 1 with better compressive strength (6.358 MPa), was in sample A (5%). Class 2 consisted of sample D (reference) and had a higher plasticity index (28.51%) and water absorption rate (11.19%). Finally, class 3, which included samples B (10%) and C (15%), had very high shrinkage and fire losses compared to other platelets. These results highlighted the possibility of using up to 5% of the coal fly ash in the production of new fired bricks with good performance.展开更多
The effects of isocyanate(IA)incorporation on the toughness and volume stability of AAFS were systematically investigated.Various IA dosages were introduced into AAFS,and their influence on mechanical properties,micro...The effects of isocyanate(IA)incorporation on the toughness and volume stability of AAFS were systematically investigated.Various IA dosages were introduced into AAFS,and their influence on mechanical properties,microstructure,and shrinkage behavior was evaluated.The experimental results indicate that,with the incorporation of 5%IA,the 28-day compressive strength reaches 48.6 MPa,the 56-day drying shrinkage decreases by 35.91%,and minimal cracking is observed in the ring test.Microstructural analyses using SEM,XRD,and FTIR reveal that IA reacts with water to form urethane and biuret,which crosslinks into a durable network structure.This network fills pores,reducing internal stresses and improving both toughness and volume stability.These findings offer new insights into optimizing alkali-activated materials for construction applications and provide a potential pathway for the development of more durable and stable geopolymers.展开更多
Municipal solid waste incineration fly ash(MSWI)is considered as one of the hazardous wastes and requires to be well disposed to reduce the contaminant to the environment.Reference to the production of coal fly ash(FA...Municipal solid waste incineration fly ash(MSWI)is considered as one of the hazardous wastes and requires to be well disposed to reduce the contaminant to the environment.Reference to the production of coal fly ash(FA)bricks,MSWI and FA were utilized to prepare autoclaved MSWI-FA block samples.Ultrasonic-assisted hydrothermal synthesis technology was used for production to explore the effect of ultrasonic pre-treatment.Compressive strength,dry density,and water absorption tests were conducted to determine the optimal ultrasonic parameters.Ultrasonic pre-treating mechanisms were investigated by SEM,FT-IR,particle size analysis,and BET.Furthermore,the micro-analyses of block samples were conducted.The heavy metal leaching concentration was studied to assess the environmental safety.The experimental results show that the ultrasonic pre-treating time,water bath temperature,and ultrasonic power of 3 h,30℃,and 840 W are the optimal,under which the compressive strength,dry density,and water absorption were 8.14 MPa,1417.48 kg/m^(3),and 0.38,respectively.It is shown that ultrasound destroys the surface structure of raw materials and smaller FA particles embed into MSWI.The particle size distribution of pre-treated raw materials mixture is wider and total pore volume is decreased by 6.3%.During hydrothermal processing,more Al-substituted tobermorite crystals are generated,which is the main source of higher strength and smaller pore volume of prepared block samples.The solidification/stabilization rates of Cu,Pb,and Zn increased by 30.77%,4.76%,and 35.29%,respectively.This study shows a feasible way to utilize MSWI as raw material for construction.展开更多
The rapid change in CO_(2) concentration levels,due to climate change,will lead to a significant reduction in the durability and safety of the vital reinforced concrete(RC)structures.Utilizing supplementary cementitio...The rapid change in CO_(2) concentration levels,due to climate change,will lead to a significant reduction in the durability and safety of the vital reinforced concrete(RC)structures.Utilizing supplementary cementitious materials,such as low calcium fly ash(LCFA)or slag,etc.,with larger percentages in concrete mixes,would lead to an increase in the carbonation depth and risk of corrosion,especially for cracked concrete sections subjected to severe CO_(2) concentration levels.This research aims to compare the carbonation depth values using two different mathematical models across various CO_(2) concentrations and crack widths,for concrete mixes composed of different percentages and types of fly ash for both uncracked and cracked RC members,at a specific time of CO_(2) exposure.Moreover,the main objective is to assess the probability of corrosion(PC)across various percentages and types of fly ash used in cracked RC decks subjected to a severe CO_(2) level.The PC would be investigated through the Montecarlo simulation method.A Crack width of 0.1 mm in the RC decks would lead to a severe impact on the PC conducted using the Al-Ameeri model compared to the Kwon and Na model,when the percentages of LCFA vary from 5%to 30%in concrete mixes.It is recommended in this research to reduce the amount of high calcium fly ash in the mixes for RC decks to a percentage below 15%instead of LCFA to inhibit the carbonation-induced corrosion and enhance the durability and serviceability of RC structures.展开更多
The fabrication of highly flame-retardant polyamide 6(PA6)composites is of great significance for expanding their practical applications.Herein,a new flame-retardant system(ADP/FA)was developed by combining aluminum d...The fabrication of highly flame-retardant polyamide 6(PA6)composites is of great significance for expanding their practical applications.Herein,a new flame-retardant system(ADP/FA)was developed by combining aluminum diethylphosphinate(ADP)with excellent flame retardancy and fly ash(FA),an economical and environmentally friendly industrial waste.Due to the synergistic flame-retardant effect of ADP/FA in the condensed phase and gas phase,the PA6 composite containing only 11 wt%of ADP/FA(mass ratio 93:7)obtained vertical burning(UL-94)tests V-0 rating with a limiting oxygen index(LOI)of 30.9%.To obtain the same flame-retardant level of PA6/ADP/FA-3,the loading amount of ADP alone was required 14 wt%.Compared with the PA6/ADP,the introduction of FA not only reduced the amount of flame retardant added but also inhibited the formation of molten droplets during combustion,greatly enhancing the fire safety of the PA6 composites.The flame-retardant performance of the ADP/FA system is superior to that of most current ADP-based synergistic strategies.In the meantime,the introduction of FA also significantly reduced the high smoke release caused by ADP flame retardant.The peak smoke production rate(pSPR)of the PA6 composite,from 0.221 m2⋅s-1(PA6/ADP)to 0.116 m2⋅s-1,represents a 47.5%decrease.This work provides a feasible solution for fabricating PA6 composites with excellent flame retardancy.展开更多
The effects of various fly ash(FA)contents on the durability and mechanical properties of recycled fine aggregate high ductility cementitious composites(RFA-HDCC)prepared with recycled fine aggregates(RFA)to fully rep...The effects of various fly ash(FA)contents on the durability and mechanical properties of recycled fine aggregate high ductility cementitious composites(RFA-HDCC)prepared with recycled fine aggregates(RFA)to fully replace natural fine aggregates was investigated.The results indicated that a 50% FA content significantly increased the compressive strength of RFA-HDCC by 13.93%.However,a?further increase in FA content led to a drastic decrease.The increased fly ash content substantially reduced the flexural and tensile strength;however,it markedly increased the matrix strain capacity,resulting in a 53.73% increase in the peak strain when FA was raised to 70%.Regarding durability,the increase in FA content negatively affected the chloride ion permeability and carbonation resistance.However,the increase in FA content initially improved the frost resistance of RFA-HDCC,peaking at 50% FA and deteriorating at 60% and 70% FA content.展开更多
文摘It is crucial to develop arsenic removal adsorbents with strong sulfur resistance under middle-low-temperature flue gas conditions(<400℃).In this work,five Fe-Ce-La oxides were prepared by co-precipitation method,and FeCeLaO/SiO_(2)-Al_(2)O_(3) composite adsorbents were prepared by coupling fly ash-based Si-Al carriers.The active components Fe-Ce-La oxides and Si-Al carriers were characterized by TPD,TG,XRF,BET and XPS,respectively.The effects of temperature,Si/Al ratio and FeCeLaO loading rate on the sulfur resistance were investigated.Results show that the SO_(2) promotes the arsenic removal of Fe_(2)O_(3),CeLaO and FeCeLaO.At 400℃,the arsenic removal efficiencies of the three oxides increase from 45.3%,72.5% and 81.3% without SO_(2) to 62.6%,80.5%and 91.0%,respectively.The SO_(2) inhibits the arsenic removal of La_(2)O_(2)CO_(3) and FeLaO,and the inhibition effect is pronounced at high temperatures.The sulfur poisoning resistance of Si-Al carriers increases with the increase of Si/Al ratio.When the Si/Al ratio is increased to 9.74,the arsenic removal efficiency in the SO_(2) environment is 13.9% higher than that in the absence of SO_(2).Introducing FeCeLaO active components is beneficial for enhancing the SO_(2) poisoning resistance of Si-Al carriers.The strong sulfur resistance of the FeCeLaO/SiO_(2)-Al_(2)O_(3) composite adsorbent results from multiple factors:protective effects of Ce on Fe,La and Al;sulfation-induced generation of Ce^(3+)and surface-adsorbed oxygen;and strong surface acidity of SiO_(2).
基金Funded by the National Basic Research Program of China (No.2009CB623105)
文摘Surfaces of grade III fly ashes were modified through mixing with carbide slag and calcining at 850 ℃ for 1 h. Mineralogical compositions and surface morphology of fly ashes before and after modification were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）, respectively. Effect of surface-modified fly ashes on compressive strength and autogenous shrinkage of blended cement pastes was investigated. Microstructures of cement pastes were examined by backscattered electron （BSE） imaging and mercury intrusion porosimetry （MIP）. The experimental results showed that β-C2S was formed on the surfaces of fly ashes after modification. Hydration ofβ-C2S on the surface-modified fly ashes densified interface zone and enhanced bond strength between particles of fly ashes and hydrated clinkers. In addition, surface modification of fly ashes tended to decrease total porosity and 10-50 nm pores of cement pastes. Surface modification of fly ashes increased compressive strength and reduced autogenous shrinkage of cement pastes.
基金Funding from CSIR, New Delhi, under network project (ESC.205)
文摘Valuable metal extraction technology from thermal power plant fly ash is limited.In the present study,aluminium is extracted from fly ash as highly pure aluminium sulphate(>99.0%)by leaching with sulphuric acid,followed by pre-concentration and successive crystallization.Two types of fly ashes from different sources,i.e.,Talcher Thermal Power Station(TTPS)and Vedanta Aluminium Company Limited(VAL)were chosen for comparative study on the extraction of aluminium as aluminium sulphate.The product is characterized by powder X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR)and thermogravimetric analysis(TGA).Purity of aluminium sulphate was also investigated by inductively coupled plasma?optical emission spectrometry(ICP?OES).The extraction efficiency of aluminium depends on the varied solid-to-liquid ratio(fly ash:18mol/L H2SO4,g/mL)and particle size of fly ashes.Physico-chemical analysis indicates that the obtained product is Al2(SO4)3·18H2O,having low iron content(0.08%).
基金Project supported by the National Natural Science Foundation of China (No. 40771096)the Natural Science Foundation of Zhejiang Province (No. R305078), China
文摘Ferrospheres in fly ashes from a coal-fired power plant were extracted by a magnetic separation technique and their microstructure was studied by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and environmental scanning electron microscopy (ESEM). Ferrospheres in fly ashes show significant iron enrichment compared to their respective fly ashes. Iron oxides in ferrospheres mainly occur as minerals magnetite (Fe3O4) and hematite (α-Fe2O3), which are derived mainly from the decomposition and oxidation of iron-bearing minerals in coal during combustion. EDX data indicate that ferrospheres also contain Si, S, Al and Ca resulting from quartz, mullite, anhydrite and amorphous materials. A large percentage of ferrospheres are commonly 5～50 μm in size. The microstructure of ferrospheres includes smooth, polygonal, dendritic, granular and molten drop characteristics. SEM coupled with EDX provided fast and accurate results of the microstructure and chemical composition of ferrospheres, and helped us to assess environmental issues related to the disposal and utilization of fly ashes.
基金This work was supported by the National Natural Science Found of China(40133010,40273035)Natural Science Found of Anhui(04045064)
文摘The Yanzhou mine district, located in southwestern Shandong Province, is about 1300 km2 with more than 8×109tons of proved coal reserves and there are 10 big power plants in this area. A large amount of coal ashes, which are regarded as waste materials, have been stockpiled in the area and have influenced the environment of the mine district. In this paper, analysis of fly ash samples from three power plants is carried out, the enrichment and concentration of trace elements, Pb, Zn, Cu and As, in coal ashes are analyzed, and petrological and mineralogical characteristics and chemical compositions of coal ashes are studied. The aim of this work is to provide basic scientific data for utilization of ashes and reduction of environmental pollutions.
文摘For the handling, treatment and utilization of fly ash from biomass combustion its chemical composition and physical properties are important. In this study eight filter fly ashes from different grate-fired biomass combustion plants were investigated. In fly ash from straw combustion high concentrations of（K） were found, whereas in the fly ash from wood combustion the concentrations of Ca and Mg were higher. The average concentration of PO3-4was similar in both types of fly ashes. In all wood fly ashes some measured heavy metal concentrations were above the limits for utilization. The straw fly ashes were much less contaminated and can be utilized. For wood fly ash most parameters showed little variation, except from one fly ash where the dust pre-separator is in poor condition. The average values were： mass median diameter 4.3 ± 0.8 μm, spread of particle size distribution19 ± 11, particle density 2620 ± 80 kg/m^3 and angle of repose 50°± 1°. The density of the straw fly ashes is lower（2260 ± 80 kg/m^3） and the spread of the size distribution is higher（72 ± 24）.For one straw combustion fly ash the values of the mass median diameter and the angle of repose were similar to the values of wood combustion fly ash, for the other straw fly ash the values differed considerably. While the particle size of this fly ash was much smaller,surprisingly the angle of repose was also lower. This can be attributed to the formation of small agglomerates in this fly ash, which were not disintegrated without a certain stress.
基金The paper is financed by the Polish State Committee for Scientific Research,project No.N N506 299139.
文摘This paper presents the effect of fly ash grain-size fractions on Portland-fly ash cement hydration and its properties. Siliceous fly ashes of size fraction of 0 - 16 and 16 - 32 μm, separated from initial fly ash samples from 1st, 2nd and 3rd hopper in ESP system, were analysed. Cement hydration was investigated by determination of hydration heat and content of Ca(OH)2 and C3S in cement samples. Water to cement ratio and initial setting time of cement pastes as well as compressive strength and microstructure of cement mortars were also analyzed. Results showed that the same amount of the same size ash fraction can give cement of lower or higher early strength and its lower or higher increase with time. Incorporation of 20 wt% of ash fraction of 0 - 16 μm can produce Portland-fly ash cement CEM II/A-V of strength class 42.5R (from 2nd hopper) or 52.5N (from 3rd hopper). Cement containing 40 wt% of ash fraction of 0 - 16 μm from 2nd and 3rd hopper can be classified as pozzolanic cements CEM IV/A-V of strength class 42.5 and normal or rapid early strength, respectively. Different development of strength of cement with addition of the same size ash fraction separated from the initial ash sample from the next hopper in ESP system is connected with higher depolymerization degree of SiO4 units in ash glass, resulting from the greater amount of AlO4 units replacing SiO4 units. Ash fraction of 16 - 32 μm shows lower depolymerisation of glass network and as a consequence lower hydration degree of C3S to portlandite and calcium silicate hydrates (C-S-H).
文摘Three fresh China coals （lignitie, bituminite and anthracite） from different geological origin and the corresponding fly and bottom ashes were studied by room temperature（RT） Mossbauer spectroscopy（MS）. The iron-bearing minerals were characterized to be mainly pyrite in all coal samples by the hyperfine parameters.Suphate（FeSO4·nH2O） was found in bituminite and anthracite coal.The MSssbauer spectra of the fly and bottom ashes as a result of pulverised coal combustion（PCC） in Xiaolongtan,Shuicheng and Luohuang Power Plants are comprised of superimposed sextets and doulets of oxides includes maghemite（γ-Fe2O3）, magnitite（Fe3O4）, haematite（α-Fe2O3）, magnesioferite （MgFe2O4）, Fe^3＋/Fe^2＋ -mullite, Fe^3＋ -glass silicate and metallic iron. The studies also show that iron-bearing minerals in coals are largely dependant on geological regions and coal rank, the composition of the corresponding fly and bottom ashes will not only depend on the type and mineralogy of the feed coal but also on the local nature of combustion.
基金Project supported by Rumah Program 2023 and Net Zero Emission Program(1507/Ⅱ.7/HK.01.00/6/2023)a research facility from the National Research and Innovation Agency of Republic of Indonesia。
文摘Recycling rare earth elements(REEs)from waste is necessary for an environmentally sustainable reuse and wastewater management approach.Na-A zeolite was synthesized from coal fly ash(CFA)and applied for Ce^(3+)adsorption.Fourier transform infrared(FTIR)spectra show peaks at 790,500 and 467 cm^(-1),which are bond vibrations of Si-O-Si,Si with Al-O and Si-O-.The surface area is 15.88 m^(2)/g,with a pore size of 2.14 nm.SEM images show a cubic shape,which indicates the formation of zeolite.Field emission and energy disperse spectroscopy(EDS)shows the formation of Si,Al,Na,and O.Na-A zeolite was applied for Ce^(3+)adsorption.The optimum conditions for Ce^(3+)adsorption are 50 ppm concentration,360 min,and pH 6.The maximum adsorption capacity is 176.49 mg/g.Based on the results,it is found that the adsorption of Ce^(3+)by Na-A zeolite is pseudo-second-order.The desorption test using HNO_(3) is more effective than using HCl and H_(2)SO_(4).A desorption efficiency of 97.22%is obtained at 4 cycles.Adsorption test using real sample wastewater demonstrates an adsorption efficiency of 83.35%.
基金Supported by Yunnan Major Scientific and Technological Projects(No.202403AA080001)National Natural Science Foundation of China(No.52074137)Yunnan Fundamental Research Projects(No.202201AT070151)。
文摘Three types of activators such as sodium hydroxide,calcium oxide and triethanolamine(TEA)are used to establish different activation environments to address the problems associated with the process of activating fly ash paste.We conducted mechanical tests and numerical simulations to understand the evolution of microstructure,and used environmental scanning electron microscopy(ESEM)and energy dispersive spectroscopy(EDS)techniques to analyze the microenvironments of the samples.The mechanical properties of fly ash paste under different activation conditions and the changes in the microstructure and composition were investigated.The results revealed that under conditions of low NaOH content(1%-3%),the strength of the sample increased significantly.When the content exceeded 4%,the rate of increase in strength decreased.Based on the results,the optimal NaOH content was identified,which was about 4%.A good activation effect,especially for short-term activation(3-7 d),was achieved using TEA under high doping conditions.The activation effect was poor for long-term strength after 28 days.The CaO content did not significantly affect the degree of activation achieved.The maximum effect was exerted when the content of CaO was 2%.The virtual cement and concrete testing laboratory(VCCTL)was used to simulate the hydration process,and the results revealed that the use of the three types of activators accelerated the formation of Ca(OH)_(2) in the system.The activators also corroded the surface of the fly ash particles,resulting in a pozzolanic reaction.The active substances in fly ash were released efficiently,and hydration was realized.The pores were filled with hydration products,and the microstructure changed to form a new frame of paste filling that helped improve the strength of fly ash paste.
基金Funded by the Natural Science Foundation of China(No.52109168)。
文摘In order to study the characteristics of pure fly ash-based geopolymer concrete(PFGC)conveniently,we used a machine learning method that can quantify the perception of characteristics to predict its compressive strength.In this study,505 groups of data were collected,and a new database of compressive strength of PFGC was constructed.In order to establish an accurate prediction model of compressive strength,five different types of machine learning networks were used for comparative analysis.The five machine learning models all showed good compressive strength prediction performance on PFGC.Among them,R2,MSE,RMSE and MAE of decision tree model(DT)are 0.99,1.58,1.25,and 0.25,respectively.While R2,MSE,RMSE and MAE of random forest model(RF)are 0.97,5.17,2.27 and 1.38,respectively.The two models have high prediction accuracy and outstanding generalization ability.In order to enhance the interpretability of model decision-making,we used importance ranking to obtain the perception of machine learning model to 13 variables.These 13 variables include chemical composition of fly ash(SiO_(2)/Al_(2)O_(3),Si/Al),the ratio of alkaline liquid to the binder,curing temperature,curing durations inside oven,fly ash dosage,fine aggregate dosage,coarse aggregate dosage,extra water dosage and sodium hydroxide dosage.Curing temperature,specimen ages and curing durations inside oven have the greatest influence on the prediction results,indicating that curing conditions have more prominent influence on the compressive strength of PFGC than ordinary Portland cement concrete.The importance of curing conditions of PFGC even exceeds that of the concrete mix proportion,due to the low reactivity of pure fly ash.
文摘Microwave-curing and mechanical grinding of fly ash have both beenadopted as effective methods for improving the early-age strength of alkali-activated fly ash(AAFA)binders.This study combined these two approaches by synthesizing AAFA using original,medium-fine,and ultrafine fly ash as precursors,and then specimens were cured with a five-stage temperature-controlled microwave.The compressive strength results indicate that the original AAFA develops the highest strength initially during microwave-curing,reaching 28 MPa at stage 2.Medium-fine AAFA exhibits the highest strength of 60 MPa when cured to stage 4-I,which is 26%higher than the peak strength of original AAFA.It is attributed to the significant rise in their specific surface area,which accelerates the dissolution of Si and Al from the precursor and facilitates the subsequent formation of N-A-S-H gels.Additionally,nanoscale zeolite crystals formed as secondary products fill the tiny gaps between amorphous products,thereby significantly improving their microstructure.In contrast,ultrafine fly ash,primarily composed of fragmented particles,necessitated a substantial amount of water,which adversely affects the absorption efficiency for microwave of AAFA specimens.Thus,ultrafine AAFA specimens consistently exhibit the lowest compressive strength.Specifically,at the end of curing,the compressive strength of these three specimens with microwave-curing is approximately 32%,59%,and 172%higher than that of the steam-cured sample,respectively.These findings demonstrate the compatibility of microwave-curing and fly ash refinement in enhancing the early compressive strength development of AAFA.
文摘In order to adjust some properties of cement grout or concrete,some mineral admixtures are usually added in the preparation.Admixtures can reduce the cement consumption and save the cost,and also adjust the workability of the material,improve the strength and durability of the cement stone,or reduce hydration heat of the composite cement.At present,the content of fly ash or slag is generally less than 50%among the composite cementitious materials that have been studied more,but there is little research on composite cementitious materials with large mineral admixture.In this paper,XRD,SEM,and adiabatic temperature rise tests were used to discuss hydration products and mechanism of composite cement grout with 90%content of fly ash and slag.The results show that the hydration of the composite cement grout is an alkali-activated hydration reaction,and the hydration products are mainly amorphous substances such as hydrated calcium silicate or hydrated calcium aluminate gel.The hydration reaction temperature rise is much lower than that of ordinary cement grout,and the time of the temperature peak is significantly delayed.
基金supported by the Polish National Science Center(Grant No.2022/06/X/ST10/00320)received by Witold Tisler.
文摘The present study investigates the engineering properties of submerged organic silt(orSi)stabilized with F-class fly ash(FA),with and without the addition of an activator(CaO).The utilization of F-class FA for soil improvement is an important aspect of sustainable and environmentally-conscious geotechnical engineering when marginal usage of lime and concrete is of great interest to engineers and societies.Currently,discussion is predominantly focused on the positive aspects of using the F-class FA,with a paucity of emphasis on the negative aspects.To explore these features more thoroughly,a series of strength and compressibility tests was conducted.The sample preparation and curing methodology were chosen to replicate the in situ conditions where soil is surcharged and submerged in water.It was found that the incorporation of F-class FA without an activator reduces the undrained shear strength of submerged orSi by about 20%–25%and permanently prevents any thixotropic strength restoration.An increase in undrained shear strength is observed when lime(3%–6%)is added to the soil–FA mixture or when only lime(in the same amount of 3%–6%)is used.Consequently,F-class FA can be successfully used as a filler for slurries with minimum lime content in soil mixing methods.The F-class FA(with or without an activator)shifts the so-called“creep delay”in time,consequently reducing the total creep settlements.The shift of“creep delay”is more considerable for orSi stabilized with lime or with FA and lime as an activator,than for orSi stabilized with pure F-class FA.
文摘This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, terracotta brick seems to meet these needs. Thus, the objective of this work was to evaluate the influence of the incorporation of coal fly ash from a thermal power plant on the physical and mechanical properties of fired bricks from grey clay in the Thicky area of Senegal. The coal fly ash was incorporated into the raw clay material in proportions of 0, 5, 10, and 15 % by weight. These two raw materials were first characterized by X-ray fluorescence spectroscopy (XRF). The XRF analyses showed that the most abundant oxides in clay were SiO2 (55.034%) and Fe2O3 (10.155%). In coal fly ash, SiO2 (38.574%) is predominant. The ash also contained Al2O3 (7.717%) and alicano-earthy melting oxides such as CaO (9.271%) and MgO (7.298%) etc. These melting oxides were necessary to facilitate the formation of the liquid phase when baking platelets. The latter, when burned at a temperature of 880°C, were characterized by determining the number of physico-mechanical parameters, such as linear shrinkage during cooking, water absorption, fire loss and compressive strength. A Hierarchical Ascending Classification of these different parameters was performed and three classes were obtained. Class 1 with better compressive strength (6.358 MPa), was in sample A (5%). Class 2 consisted of sample D (reference) and had a higher plasticity index (28.51%) and water absorption rate (11.19%). Finally, class 3, which included samples B (10%) and C (15%), had very high shrinkage and fire losses compared to other platelets. These results highlighted the possibility of using up to 5% of the coal fly ash in the production of new fired bricks with good performance.
基金Funded by the National Key R&D Program of China(No.2022YFC3803400)。
文摘The effects of isocyanate(IA)incorporation on the toughness and volume stability of AAFS were systematically investigated.Various IA dosages were introduced into AAFS,and their influence on mechanical properties,microstructure,and shrinkage behavior was evaluated.The experimental results indicate that,with the incorporation of 5%IA,the 28-day compressive strength reaches 48.6 MPa,the 56-day drying shrinkage decreases by 35.91%,and minimal cracking is observed in the ring test.Microstructural analyses using SEM,XRD,and FTIR reveal that IA reacts with water to form urethane and biuret,which crosslinks into a durable network structure.This network fills pores,reducing internal stresses and improving both toughness and volume stability.These findings offer new insights into optimizing alkali-activated materials for construction applications and provide a potential pathway for the development of more durable and stable geopolymers.
基金Funded by the National Natural Science Foundation of China(No.52178241)the National Key Research and Development Program of China during the Fourteenth Five-Year Plan Period(No.2021YFB3802001)+1 种基金the Shanghai Science and Technology Innovation Action Plan(No.23D21201401)the Key Research and Development of the Shaanxi Province of China(No.2022GY-163)。
文摘Municipal solid waste incineration fly ash(MSWI)is considered as one of the hazardous wastes and requires to be well disposed to reduce the contaminant to the environment.Reference to the production of coal fly ash(FA)bricks,MSWI and FA were utilized to prepare autoclaved MSWI-FA block samples.Ultrasonic-assisted hydrothermal synthesis technology was used for production to explore the effect of ultrasonic pre-treatment.Compressive strength,dry density,and water absorption tests were conducted to determine the optimal ultrasonic parameters.Ultrasonic pre-treating mechanisms were investigated by SEM,FT-IR,particle size analysis,and BET.Furthermore,the micro-analyses of block samples were conducted.The heavy metal leaching concentration was studied to assess the environmental safety.The experimental results show that the ultrasonic pre-treating time,water bath temperature,and ultrasonic power of 3 h,30℃,and 840 W are the optimal,under which the compressive strength,dry density,and water absorption were 8.14 MPa,1417.48 kg/m^(3),and 0.38,respectively.It is shown that ultrasound destroys the surface structure of raw materials and smaller FA particles embed into MSWI.The particle size distribution of pre-treated raw materials mixture is wider and total pore volume is decreased by 6.3%.During hydrothermal processing,more Al-substituted tobermorite crystals are generated,which is the main source of higher strength and smaller pore volume of prepared block samples.The solidification/stabilization rates of Cu,Pb,and Zn increased by 30.77%,4.76%,and 35.29%,respectively.This study shows a feasible way to utilize MSWI as raw material for construction.
文摘The rapid change in CO_(2) concentration levels,due to climate change,will lead to a significant reduction in the durability and safety of the vital reinforced concrete(RC)structures.Utilizing supplementary cementitious materials,such as low calcium fly ash(LCFA)or slag,etc.,with larger percentages in concrete mixes,would lead to an increase in the carbonation depth and risk of corrosion,especially for cracked concrete sections subjected to severe CO_(2) concentration levels.This research aims to compare the carbonation depth values using two different mathematical models across various CO_(2) concentrations and crack widths,for concrete mixes composed of different percentages and types of fly ash for both uncracked and cracked RC members,at a specific time of CO_(2) exposure.Moreover,the main objective is to assess the probability of corrosion(PC)across various percentages and types of fly ash used in cracked RC decks subjected to a severe CO_(2) level.The PC would be investigated through the Montecarlo simulation method.A Crack width of 0.1 mm in the RC decks would lead to a severe impact on the PC conducted using the Al-Ameeri model compared to the Kwon and Na model,when the percentages of LCFA vary from 5%to 30%in concrete mixes.It is recommended in this research to reduce the amount of high calcium fly ash in the mixes for RC decks to a percentage below 15%instead of LCFA to inhibit the carbonation-induced corrosion and enhance the durability and serviceability of RC structures.
基金financially supported by the Natural Science Foundation of China(52173069)the Key Research and Development Projects in Heilongjiang Province(2024ZXDXA29)+1 种基金the Natural Science Foundation of Heilongjiang Province(LH2024B004)the Fundamental Research Funds for the Central Universities(ZHLJZR241700006).
文摘The fabrication of highly flame-retardant polyamide 6(PA6)composites is of great significance for expanding their practical applications.Herein,a new flame-retardant system(ADP/FA)was developed by combining aluminum diethylphosphinate(ADP)with excellent flame retardancy and fly ash(FA),an economical and environmentally friendly industrial waste.Due to the synergistic flame-retardant effect of ADP/FA in the condensed phase and gas phase,the PA6 composite containing only 11 wt%of ADP/FA(mass ratio 93:7)obtained vertical burning(UL-94)tests V-0 rating with a limiting oxygen index(LOI)of 30.9%.To obtain the same flame-retardant level of PA6/ADP/FA-3,the loading amount of ADP alone was required 14 wt%.Compared with the PA6/ADP,the introduction of FA not only reduced the amount of flame retardant added but also inhibited the formation of molten droplets during combustion,greatly enhancing the fire safety of the PA6 composites.The flame-retardant performance of the ADP/FA system is superior to that of most current ADP-based synergistic strategies.In the meantime,the introduction of FA also significantly reduced the high smoke release caused by ADP flame retardant.The peak smoke production rate(pSPR)of the PA6 composite,from 0.221 m2⋅s-1(PA6/ADP)to 0.116 m2⋅s-1,represents a 47.5%decrease.This work provides a feasible solution for fabricating PA6 composites with excellent flame retardancy.
基金Funded by the Natural Science Foundation of Jiangsu Province(No.BK20220626)Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX24_3174)Taizhou Science and Technology Support Programme(Social Development)Directive Project(No.TS202432)。
文摘The effects of various fly ash(FA)contents on the durability and mechanical properties of recycled fine aggregate high ductility cementitious composites(RFA-HDCC)prepared with recycled fine aggregates(RFA)to fully replace natural fine aggregates was investigated.The results indicated that a 50% FA content significantly increased the compressive strength of RFA-HDCC by 13.93%.However,a?further increase in FA content led to a drastic decrease.The increased fly ash content substantially reduced the flexural and tensile strength;however,it markedly increased the matrix strain capacity,resulting in a 53.73% increase in the peak strain when FA was raised to 70%.Regarding durability,the increase in FA content negatively affected the chloride ion permeability and carbonation resistance.However,the increase in FA content initially improved the frost resistance of RFA-HDCC,peaking at 50% FA and deteriorating at 60% and 70% FA content.
