Al-Cu-Mn alloys are widely used to produce automobile components like cylinder heads and engine blocks because of their capability to retain excellent thermal and mechanical characteristics at high temperatures.Howeve...Al-Cu-Mn alloys are widely used to produce automobile components like cylinder heads and engine blocks because of their capability to retain excellent thermal and mechanical characteristics at high temperatures.However,the Al-Cu-Mn-based alloys demonstrate restricted fluidity,leading to casting defects such as shrinkage and incomplete filling.This research investigated the microstructure and fluidity of Al-4.7Cu-1.0Mn-0.5Mg(wt%)alloy with minor cerium(Ce)addition.The as-cast alloys predominantly compriseα-Al matrix,accompanied by the presence of Al_(2)Cu,Al_(6)Mn,and Al_(8)Cu_(4)Ce phases.The influence of adding Ce on the fluidity of the Al-4.7Cu-1.0Mn-0.5Mg alloy was investigated using a trispiral fluidity test mold in this research.The findings suggest that the addition of Ce within the range of 0.1 wt%to 0.5 wt%in the Al-4.7Cu-1.0Mn-0.5Mg alloy results in an enhancement in fluidity.Specifically,the alloy containing 0.4 wt%Ce exhibits a significant increase in fluidity distance,from 349.7 to 485.7 mm.This improvement can be attributed to the reduction in viscosity,the refinement of secondary dendrite arm spacing,and the modification of secondary phase particles.However,a higher concentration of Ce leads to a decrease in fluidity length,potentially due to the formation of Al_(8)Cu_(4)Ce.展开更多
The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment...The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment.The results showed that the length of the spiral fluidity sample increases from 302 to 756 mm as the pouring temperature increases from 680 to 740℃,and from 293 to 736 mm as the mold temperature increases from 200 to 400℃.The hot tearing susceptibility(HTS)firstly decreases and then increases with increasing pouring and mold temperatures,which is mainly caused by the oxide inclusion originating from the high activity of Li at excessive pouring temperature.Excessive pouring and mold temperatures easily produce oxide inclusions and holes,leading to a reduction in fluidity and an increase in HTS of the alloy.Combining the experimental and simulation results,the optimized pouring and mold temperatures are~720℃ and~300℃ for the cast Al-Li alloy,respectively.展开更多
This paper discusses an experimental investigation into the fluidity of AZ91D-1 wt.%Ca O magnesium melt via induction for thin-section investment casting.Plaster molds with thin spiral cavities(0.5 to 1.5 mm square se...This paper discusses an experimental investigation into the fluidity of AZ91D-1 wt.%Ca O magnesium melt via induction for thin-section investment casting.Plaster molds with thin spiral cavities(0.5 to 1.5 mm square sections)were designed and manufactured to assess the impact of casting conditions on filling length,as magnesium alloys cause severe melting and melt-mold exothermic reactions,making investment casting challenging.Combinations of traditional Mg-mold reaction mitigation techniques,such as applying a protective mold coating(Yttria)and vacuum,were examined to determine their role in the filling process.The results suggest that when induction is employed to melt reactive alloys,these methods are not always beneficial,as initially thought.Particularly at higher melt temperatures,the combination of Yttria-coated molds with low-pressure vacuum induction significantly reduce fluidity:vacuum induced melt levitation which promotes oxidation with the residual atmosphere;and Yttria-coating cracking due to thermal stress during the mold fabrication slows filling and promotes significant melt-mold reaction.This study shows that best results to investment cast thin-sections are obtained by avoiding both vacuum and protective coatings,providing a viable route for the precision manufacturing of stent biomedical devices.展开更多
Tissue expansion is a widely utilized technique in plastic and reconstructive surgery;however,the biological mechanisms underlying the skin response remain poorly understood.We propose that tissue fluidity,the transit...Tissue expansion is a widely utilized technique in plastic and reconstructive surgery;however,the biological mechanisms underlying the skin response remain poorly understood.We propose that tissue fluidity,the transition of tissue from a solid-like state to a fluid-like state,plays a pivotal role in enabling the reorganization of the epidermal structure and cellular spatial order,which is essential for effective tissue expansion.Drawing parallels between fluidity in materials science and biological systems,we suggest that the fluid-like behavior in the skin may be critical for mechanical adaptability.Understanding the influence of tissue fluidity may open pathways for modulating this process,potentially enhancing tissue expansion efficiency,reducing procedural duration,and improving clinical outcomes.This perspective highlights the importance of investigating the biological dynamics of tissue fluidity and exploring the potential for targeted manipulation of fluidity-related pathways to optimize tissue expansion.Such advancements could profoundly affect regenerative and reconstructive surgical practices.展开更多
In addition to the organic matter type,abundance,thermal maturity,and shale reservoir space,the preservation conditions of source rocks play a key factor in affecting the quantity and quality of retained hydrocarbons ...In addition to the organic matter type,abundance,thermal maturity,and shale reservoir space,the preservation conditions of source rocks play a key factor in affecting the quantity and quality of retained hydrocarbons in source rocks of lacustrine shale,yet this aspect has received little attention.This paper,based on the case analysis,explores how preservation conditions influence the enrichment of mobile hydrocarbons in shale oil.Research showns that good preservation conditions play three key roles.(1)Ensure the retention of sufficient light hydrocarbons(C_(1)–C_(13)),medium hydrocarbons(C_(14)–C_(25))and small molecular aromatics(including 1–2 benzene rings)in the formation,which enhances the fluidity and flow of shale oil;(2)Maintain a high energy field(abnormally high pressure),thus facilitating the maximum outflow of shale oil;(3)Ensure that the retained hydrocarbons have the miscible flow condition of multi-component hydrocarbons(light hydrocarbons,medium hydrocarbons,heavy hydrocarbons,and heteroatomic compounds),so that the heavy hydrocarbons(C_(25+))and heavy components(non-hydrocarbons and asphaltenes)have improved fluidity and maximum flow capacity.In conclusion,in addition to the advantages of organic matter type,abundance,thermal maturity,and reservoir space,good preservation conditions of shale layers are essential for the formation of economically viable shale oil reservoirs,which should be incorporated into the evaluation criteria of shale oil-rich areas/segments and considered a necessary factor when selecting favorable exploration targets.展开更多
A spiral fluidity test model of superalloys with 10 mm in height and 3 mm in thickness was designed to evaluate the fluidity of two distinct Ni-based superalloys IN718 and IN939.The factors influencing fluidity are as...A spiral fluidity test model of superalloys with 10 mm in height and 3 mm in thickness was designed to evaluate the fluidity of two distinct Ni-based superalloys IN718 and IN939.The factors influencing fluidity are ascertained through comparative analysis utilizing methodologies such as JMat Pro,differential scanning calorimetry and high-temperature confocal laser scanning microscopy.The results show that under identical testing conditions,the fluidity of the IN939 superalloy surpasses that of the IN718 superalloy.When subjected to the same temperature,the melt viscosity and surface tension of IN939 superalloy are considerably reduced relative to those of IN718 superalloy,which is beneficial to improving the melt fluidity.Furthermore,the liquidus temperature and solidification range for the IN939 superalloy are both smaller compared with those of the IN718 superalloy.This condition proves advantageous in delaying dendrite coherency,thereby improving fluidity.展开更多
Mg-Zn-based alloys have been widely used in computer,communication,and consumer(3C)products due to excellent thermal conductivity.However,it is still a challenge to balance their mechanical performance and thermal con...Mg-Zn-based alloys have been widely used in computer,communication,and consumer(3C)products due to excellent thermal conductivity.However,it is still a challenge to balance their mechanical performance and thermal conductivity.Here,we investigate microstructure,mechanical performance,thermal conductivity and metal fluidity of Mg-5Zn(wt.%)alloy after Cu alloying by experimental and simulation methods.First,Mg-5Zn alloy consist ofα-Mg matrix and interdendritic MgZn phases.As the Cu content increases,however,MgZn phases disappear but intragranular Mg_(2)Cu and interdendritic MgZnCu phases appear in Mg-5Zn-Cu alloys.Besides,the grain size ofα-Mg phase is refined and the volume fraction of MgZnCu phase increases as the Cu content increases.Second,Cu addition is found to improve thermal conductivity of Mg-5Zn alloy remarkably.Especially,Mg-5Zn-4Cu alloy exhibits the best thermal conductivity of 124 W/(m·K),which is mainly due to the significant reduction in both solid solubility of Zn in theα-Mg matrix and lattice distortion ofα-Mg matrix.Moreover,a stable crystal structure of MgZnCu phase also contributes to an increased thermal conductivity based on first principles and molecular dynamics simulations.Third,Cu addition simultaneously enhances strength and ductility of Mg-5Zn alloy.Tensile yield strength and elongation of Mg-5Zn-6Cu alloy reach 117 MPa and 18.0%,respectively,which is a combined result of refinement,solution,second phase,and dislocation strengthening.Finally,combined with a phase field simulation,we found that Cu addition enhances metal fluidity of Mg-5Zn alloy.On the one hand,Cu alloying not only delays dendrite growth but also prolongs solidification time.On the other hand,MgZnCu phase stabilizes the dendrite growth of theα-Mg phases by reducing energy consumption during solidification of liquid metal.This work demonstrates that Cu alloying is an ideal strategy for synergistically improving the thermal conductivity,mechanical performance and metal fluidity of Mg-based alloys.展开更多
Grain refinement is a satisfying method to enhance the comprehensive performance of Mg alloys,and using grain refiners to improve the quality of Mg castings has become a common practice in the current casting industry...Grain refinement is a satisfying method to enhance the comprehensive performance of Mg alloys,and using grain refiners to improve the quality of Mg castings has become a common practice in the current casting industry.In this study,the effects of Al-CeO_(2)-Mg grain refiner addition on microstructure,cast fluidity,and mechanical properties of AZ91 alloy were systemically investigated by OM,SEM,DSC,TEM,sand Archimedean spiral mold fluidity test,and tensile test.The results show that the Al-CeO_(2)-Mg grain refiner has a remarkable effect on as-cast AZ91 alloy including notable grain refinement,enhancement of cast fluidity,and improvement of tensile properties.The average grain size of AZ91 alloy is refined by 63%with 1.0wt.%Al-CeO_(2)-Mg grain refiner.Meanwhile,the casting flow length of the as-cast AZ91 alloy is increased from 332 mm to 440 mm.The improvement of cast fluidity is attributed to the decreased liquidus temperature,shortening of solid-liquid two-phase temperature range,and refinement of microstructure.展开更多
H +_ATPase activity of tonoplast in roots of Hordeum vulgare L. cv. 'Tanyin 2' (salt_tolerant cultivar) increased when the roots were exposed to 50-200 mmol/L NaCl for 2 d, and decreased when NaCl concentrati...H +_ATPase activity of tonoplast in roots of Hordeum vulgare L. cv. 'Tanyin 2' (salt_tolerant cultivar) increased when the roots were exposed to 50-200 mmol/L NaCl for 2 d, and decreased when NaCl concentration was increased to 600 mmol/L. In 'Kepin 7' (salt_sensitive cultivar), tonoplast H +_ATPase activity in roots also increased at lower levels of NaCl (50-100 mmol/L), but decreased at higher levels of NaCl (200-600 mmol/L). Tonoplast fluidity in roots of 'Tanyin 2' decreased at 50-200 mmol/L NaCl, and increased significantly at 600 mmol/L NaCl. Under salt stress, the change of tonoplast fluidity was identical with that of the ratio of unsaturated fatty acids to saturated fatty acids in tonoplast lipid of barley roots. It is proposed that the increase of tonoplast fluidity due to increased degree of unsaturation of fatty acids is one of the reasons leading to the decrease of H +_ATPase activity under higher level of NaCl stress.展开更多
With in vitro spin labeling electron spin resonance (ESR) spectroscopy, we have studied the effects of Bu Yang Huan Wu (BYHW) decoction and its effective constituents such as astragaloside IV ferulic acid, chua...With in vitro spin labeling electron spin resonance (ESR) spectroscopy, we have studied the effects of Bu Yang Huan Wu (BYHW) decoction and its effective constituents such as astragaloside IV ferulic acid, chuanxiongzine, rutin, chlorogenic acid, 9,10 dimethoxy pterocarpane 7 O β D glucoside, calycosin, formononetin, calycosin 7 O glucoside, paeoniflorin, paeonal and quercein on the cell membrane fluidity of a rat brain which was modeled after the dual cervical arteries were intercepted and released for realizing an ischemia reperfusion injury which was selected as a brain stroke model. Our results indicated that the cell membrane fluidity in the model group decreased approximately 8% compared with the control group, and after brain cells were incubatied with species, the membrane fluidity could be recovered closely to the control level depending on the BYHW decoction and its different constituents. As the membrane fluidity is a very sensitive biological index which reflectsd the cell status, our method will be useful to study the molecular mechanism of tradition Chinese medicine (TCM) and its combination recipe.展开更多
The main purpose of this study was to investigate the protective actions of captopril and cicaprost on changes of membrane fluidity of cultured neonatal rat myocardial cells exposed to anoxia and sugar deprivation.Lip...The main purpose of this study was to investigate the protective actions of captopril and cicaprost on changes of membrane fluidity of cultured neonatal rat myocardial cells exposed to anoxia and sugar deprivation.Lipid peroxidation level estimated by determining the thiobarbituric acid reactive substance(TBARS)content and lactate dehydrogenase(LDH)released in culture medium was also observed in order to examine other membrane-related changes due to anoxia.Membrane fluidity was monitored by measuring changes in the steady state fluorescence anisotropy(r_s)by fluorescence spectroscopy.The r_s value,TBARS level and LDH release were significantly increased after 3 h anoxia.Captopril(180 μmol/L),cicaprost(30 nmol/L)and indomethacin(1μmol/L)did not alter r_s, TBARS level and LDH activity of normal cultured neonatal rat myocardial cells.However,both captopril and cicaprost significantly prevented the increases of r_s,TBARS content and LDH release in those cells exposed to anoxia and sugar deprivation.lndomethacin abolished the actions of captopril on TBARS production and LDH release,but maintained its membrane fluidity protection.These results indicate that captopril and cicaprost protect membrane fluidity and lipid peroxidation changes in anoxia- injured myocardial cells.The action mechanism of captopril may be due,in part,to stimulation of prostacyclin synthesis and/or release.展开更多
Adding polypropylene(PP)fibers and coarse aggregates has become a popular way to enhance the strength and stability of the cemented tailings backfilling(CTB)body.It is essential to explore the influence of tailings-ag...Adding polypropylene(PP)fibers and coarse aggregates has become a popular way to enhance the strength and stability of the cemented tailings backfilling(CTB)body.It is essential to explore the influence of tailings-aggregate ratio and fiber content on the mechanical properties of CTB samples.The comprehensive tests of the unconfined compressive strength(UCS),slump and microstructure were designed,and the regression models were established to characterize the effect of the strength,ductility and fluidity.The results indicate that the tailings-aggregate ratio of 5:5 and PP fiber content of 0.5 kg/m^(3) are the optimum point considering the UCS,cracking strain,peak strain and post-peak ductility.The tailings-aggregate ratio is consistent with the unary quadratic to the UCS and a linear model with a negative slope to the slump.Microstructural analysis indicates that PP fiber tends to bridge the cracks and rod-mill sand to serve as the skeleton of the paste matrix,which can enhance the compactness and improve the ductility of the CTB.The results presented here are of great significance to the understanding and application of coarse aggregates and fibers to improve the mechanical properties of CTB.展开更多
To investigate the thixotropic fluidities, microstructures and mechanical properties of semi-solid AZ91D magnesium alloy during reheating, a self-made die set with channels of different sizes were used. The results sh...To investigate the thixotropic fluidities, microstructures and mechanical properties of semi-solid AZ91D magnesium alloy during reheating, a self-made die set with channels of different sizes were used. The results show that critical forming forces and maximal forming forces could be obtained and related to the holding times in the semi-solid forming process. In the holding time of 0-2700 s, with increasing the holding time, maximal forming force decreased sharply and critical forming force decreased slowly. In the whole thixotropic flowing process, the filling-in was steady and the surface fineness was good. The forming force increased when the slurry changed the flowing direction or flowed from the big-diameter chamber to the small-diameter one. The tensile strength and elongation to failure of the sample after holding time for 2700 s, compared to as-cast sample, are increased by approximately 42.7% and 180%, respectively, and the fractured surfaces presented dimple-like pattern.展开更多
The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO...The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO ratios prepared on the basis of the range of oxide contents of Zhundong coal ash were investigated in this study. The results show that with the MgO/CaO ratio increase, the initial crystallization temperature increases, and the main temperature range of crystallization ratio growth moves to higher temperature range gradually which causes Tp25(Tp25is the temperature corresponding to the viscosity of 25 Pa·s)to increase. Mg-rich crystals are formed preferentially than Ca-rich crystals when adding the same amount of MgO and CaO during cooling. The effective slagging operating temperature range decrease from 217 ℃ for the slag with a 0:4 MgO/CaO ratio to 44 ℃ for the slag with a 4:0 MgO/CaO ratio with the MgO/CaO ratio increase. The slags with 2:2 and 1:3 MgO/CaO ratios show similar effective slagging operating temperature range, Tp25and the temperature corresponding to the viscosity of 2 Pa·s.However, compared with the slag with a 1:3 MgO/CaO ratio, the crystallization ratio and rate of slag with a 2:2 MgO/CaO ratio are lower within lower temperature range(1300–1200 ℃), causing its lower critical viscosity temperature and wider actual operating temperature range. Of the five slags, the widest effective slagging operating temperature range and the lowest Tp25of the slag with a 0:4 MgO/CaO ratio due to its low crystallization ratio, and wider actual operating temperature range of the slag with a 2:2 MgO/CaO ratio make the two slags suitable for slag discharge of EFB gasifier.展开更多
Understanding the flow characteristics of amorphous metal melts is important for casting and molding processes.Fluidity of Zr-based amorphous metal melts was determined by using a self-designed apparatus.Phase analysi...Understanding the flow characteristics of amorphous metal melts is important for casting and molding processes.Fluidity of Zr-based amorphous metal melts was determined by using a self-designed apparatus.Phase analysis demonstrated that the fluidity test samples were fuUy amorphous structure.The onset crystallization temperature significantly moved toward high temperature with the increases of casting temperature,which improved the glass-forming ability and thermal stability of Zr-based amorphous metal.Fluidity test results demonstrated that the fluidity length increased monotonically with the increases of temperature,pressure,and runner diameter.By identifying the types and quantities of the defect in castings,it could conclude that smooth filling processes occurred under appropriate conditions.Experimental results indicated that the flow behavior of the Zr-based amorphous metal melts strongly depended on the casting temperature and equivalent thickness.Constitutive equation based on Newton's law of heat exchange and Rayleigh rule was established to'evaluate the fluidity of Zr-based amorphous metal melts.Theoretical calculations and experimental tests were basically coincided with each other.The determined optimal casting temperatures and equivalent thicknesses were adopted to successfully fabricate a series of fully shaped castings through gravity casting.展开更多
The influence of ultrasonic degassing process on fluidity and hardness of secondary Al7Si0.3Mg alloy castings was studied by Weibull analysis. This work makes a contribution about fluidity and hardness distribution of...The influence of ultrasonic degassing process on fluidity and hardness of secondary Al7Si0.3Mg alloy castings was studied by Weibull analysis. This work makes a contribution about fluidity and hardness distribution of secondary aluminum alloys with ultrasonic degassing phenomena using a two-parameter form of Weibull analysis. Results show that both hardness and fluidity of alloy are improved after the ultrasonic degassing process. Average efficiency of ultrasonic degassing on fluidity measurements is 31.71%, whereas on hardness values is 8.48%. The Brinell hardness of 45.7 and fluidity of 19.5 of Weibull modulus were achieved as the most reliable and reproducible after 45 s ultrasonic degassing process against 15 s and 30 s ultrasonic degassing processes. The value of 70.08 HB is obtained from ultrosonic degassing, which is equivalent to sand casting of primary Al7Si0.3Mg aluminum alloy, and the highest value of 56.4 cm for 45 s after ultrasonic degassing of fluidity was measured.展开更多
After bilateral carotid artery occlusion for 30 minutes and reperfusion for 2 hours, distinct pathological changes presented in the cerebral cortex and cerebellum of rats. Compared with normal rats, nerve cell membran...After bilateral carotid artery occlusion for 30 minutes and reperfusion for 2 hours, distinct pathological changes presented in the cerebral cortex and cerebellum of rats. Compared with normal rats, nerve cell membrane fluidity significantly decreased in ischemia/reperfusion rats as detected by spin-labeling electron spin resonance, consistent with order parameter S and rotational correlation time TC measurements. Brain nerve cells from rats with ischemia/reperfusion injury were cultured with 1-100 mg/mL Buyang Huanwu decoction. Results showed that Buyang Huanwu decoction gradually increased membrane fluidity dose-dependently to normal levels, and eliminated hydroxide （OH＇） and superoxide （O2＇） free radicals dose-dependenUy. These findings suggest that Buyang Huanwu decoction can protect against cell membrane fluidity changes in rats with ischemia/ reperfusion injury by scavenging free radicals.展开更多
Differential effects of methamidophos and three pyrethroids on ATPase activity and membrane fluidity of mitochondria were investigated between the wolf spider（Pirata subpiraticus（Boes.et Str.））and the rice stem bo...Differential effects of methamidophos and three pyrethroids on ATPase activity and membrane fluidity of mitochondria were investigated between the wolf spider（Pirata subpiraticus（Boes.et Str.））and the rice stem borer（Chilo suppressalis（Walker））.Based on a comparison of LD_（50） values,the toxicities of the tested insecticides were higher to the wolf spider than to the rice stem borer.Cyhalothrin at 1×10^（–4） mmol L^（–1） caused inhibition of the mitochondrial Na~＋-K~＋-ATPase and Ca^（2＋）-Mg^（2＋）-ATPase activities,and it’s inhibitions on Na＋-K＋-ATPase and Ca^（2＋）-Mg^（2＋）-ATPase activities were significantly higher in the wolf spider（44 and 28%）than in the rice stem borer（19 and 11%）.Methamidophos at 1×10^（–4） mmol L^（–1） decreased Ca^（2＋）-Mg^（2＋）-ATPase activity by 16 and 27%in the wolf spider and the rice stem borer,respectively,but no significant effect on the specific activity of Na＋-K＋-ATPase was observed.The DPH（1,6-diphenyl-1,3,5-hexatriene）fluorescence polarization values of mitochondrial membranes were not significantly affected by methamidophos in either species.However,cyhalothrin and alpha-cypermethrin induced the values of DPH polarization of mitochondrial membrane increasing with the concentration of cyhalothrin and alpha-cypermethrin from 20 to 100μmol L^（–1） in the rice stem borer and the wolf spider.Effect of ethofenprox on fluidity of the wolf spider and the rice stem borer was contrary.These results suggest that both inhibition of membrane ATPase and changes of membrane fluidity could be appended to the action mechanisms of pyrethroid insecticides.展开更多
Objective:To evaluate effects of epigallocatechin-3-gallate (EGCG) on the viability, membrane properties, and zinc distribution, with and without the presence of Zn2+, in human prostate carcinoma LNCaP cells. Methods:...Objective:To evaluate effects of epigallocatechin-3-gallate (EGCG) on the viability, membrane properties, and zinc distribution, with and without the presence of Zn2+, in human prostate carcinoma LNCaP cells. Methods: We examined changes in cellular morphology and membrane fluidity of LNCaP cells, distribution of cellular zinc, and the incorporated portion of EGCG after treatments with EGCG, Zn2+, and EGCG+Zn2+. Results: We observed an alteration in cellular morphology and a decrease in membrane fluidity of LNCaP cells after treatment with EGCG or Zn2+. The proportion of EGCG incorporated into liposomes treated with the mixture of EGCG and Zn2+ at the ratio of 1:1 was 90.57%, which was significantly higher than that treated with EGCG alone (30.33%). Electron spin resonance (ESR) studies and determination of fatty acids showed that the effects of EGCG on the membrane fluidity of LNCaP were decreased by Zn2+. EGCG accelerated the accumulation of zinc in the mitochondria and cytosol as observed by atomic absorption spectrometer. Conclusion: These results show that EGCG interacted with cell membrane, decreased the membrane fluidity of LNCaP cells, and accelerated zinc accumulation in the mitochondria and cytosol, which could be the mechanism by which EGCG inhibits proliferation of LNCaP cells. In addition, high concentrations of Zn2+ could attenuate the actions elicited by EGCG.展开更多
Effects of organosilane-modified PCE (OS-PCE) on the fluidity and the hydration properties of cement-fly ash (FA) composite binder were systematically analyzed.The experimental results show that OS-PCE possesses respe...Effects of organosilane-modified PCE (OS-PCE) on the fluidity and the hydration properties of cement-fly ash (FA) composite binder were systematically analyzed.The experimental results show that OS-PCE possesses respectively 36.98% and 36.67% higher saturated adsorption amount on cement and FA,in comparison with ordinary PCE,and can contribute to higher fluidity of cement-FA composite binder.The addition of OS-PCE retards hydration process of cement-FA composite binder proportionally with the dosage of OS-PCE,but promotes the hydration kinetics of the composite binder.The reactivity enhancement is attributed to the well-dispersed FA by OS-PCE,which provides more nucleation sites for the reaction of heterogeneous C-S-H and enhances the contact with water to react with CH forming pozzolanic C-S-H.Well-distributed hydration products are exhibited in the hardened binder added with OS-PCE,with a large number of hydrated gels uniformly fill in the pores and gaps,which improves the compaction of the hardened structure.展开更多
基金Project supported by the National Natural Science Foundation of China (52171030)the Key Basic Research Project of the Basic Strengthen Program (2021-JCJQ-ZD-043-00)the National Key Research and Development Program of China (2018YFA0702903)。
文摘Al-Cu-Mn alloys are widely used to produce automobile components like cylinder heads and engine blocks because of their capability to retain excellent thermal and mechanical characteristics at high temperatures.However,the Al-Cu-Mn-based alloys demonstrate restricted fluidity,leading to casting defects such as shrinkage and incomplete filling.This research investigated the microstructure and fluidity of Al-4.7Cu-1.0Mn-0.5Mg(wt%)alloy with minor cerium(Ce)addition.The as-cast alloys predominantly compriseα-Al matrix,accompanied by the presence of Al_(2)Cu,Al_(6)Mn,and Al_(8)Cu_(4)Ce phases.The influence of adding Ce on the fluidity of the Al-4.7Cu-1.0Mn-0.5Mg alloy was investigated using a trispiral fluidity test mold in this research.The findings suggest that the addition of Ce within the range of 0.1 wt%to 0.5 wt%in the Al-4.7Cu-1.0Mn-0.5Mg alloy results in an enhancement in fluidity.Specifically,the alloy containing 0.4 wt%Ce exhibits a significant increase in fluidity distance,from 349.7 to 485.7 mm.This improvement can be attributed to the reduction in viscosity,the refinement of secondary dendrite arm spacing,and the modification of secondary phase particles.However,a higher concentration of Ce leads to a decrease in fluidity length,potentially due to the formation of Al_(8)Cu_(4)Ce.
基金financially supported by the National Natural Science Foundation of China(Nos.51871148,51821001)。
文摘The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment.The results showed that the length of the spiral fluidity sample increases from 302 to 756 mm as the pouring temperature increases from 680 to 740℃,and from 293 to 736 mm as the mold temperature increases from 200 to 400℃.The hot tearing susceptibility(HTS)firstly decreases and then increases with increasing pouring and mold temperatures,which is mainly caused by the oxide inclusion originating from the high activity of Li at excessive pouring temperature.Excessive pouring and mold temperatures easily produce oxide inclusions and holes,leading to a reduction in fluidity and an increase in HTS of the alloy.Combining the experimental and simulation results,the optimized pouring and mold temperatures are~720℃ and~300℃ for the cast Al-Li alloy,respectively.
基金financed by National Funds through the Portuguese funding agency,FCT–Funda??o para a Ciência e a Tecnologia,within the strategic projects UIDB/04436/2020,UIDB/00481/2020 and LA/P/0063/2020(DOI 10.54499/LA/P/0063/2020)。
文摘This paper discusses an experimental investigation into the fluidity of AZ91D-1 wt.%Ca O magnesium melt via induction for thin-section investment casting.Plaster molds with thin spiral cavities(0.5 to 1.5 mm square sections)were designed and manufactured to assess the impact of casting conditions on filling length,as magnesium alloys cause severe melting and melt-mold exothermic reactions,making investment casting challenging.Combinations of traditional Mg-mold reaction mitigation techniques,such as applying a protective mold coating(Yttria)and vacuum,were examined to determine their role in the filling process.The results suggest that when induction is employed to melt reactive alloys,these methods are not always beneficial,as initially thought.Particularly at higher melt temperatures,the combination of Yttria-coated molds with low-pressure vacuum induction significantly reduce fluidity:vacuum induced melt levitation which promotes oxidation with the residual atmosphere;and Yttria-coating cracking due to thermal stress during the mold fabrication slows filling and promotes significant melt-mold reaction.This study shows that best results to investment cast thin-sections are obtained by avoiding both vacuum and protective coatings,providing a viable route for the precision manufacturing of stent biomedical devices.
基金supported by the National Natural Science Foundation of China(grant nos.82102343 and 82372536)the Shanghai Municipal Health Commission Health Industry Clinical Research Special Program(grant no.20244Y0031)the Shanghai“Rising Stars of Medical Talents”Youth Development Program(Youth Medical Talents-Specialist Program).
文摘Tissue expansion is a widely utilized technique in plastic and reconstructive surgery;however,the biological mechanisms underlying the skin response remain poorly understood.We propose that tissue fluidity,the transition of tissue from a solid-like state to a fluid-like state,plays a pivotal role in enabling the reorganization of the epidermal structure and cellular spatial order,which is essential for effective tissue expansion.Drawing parallels between fluidity in materials science and biological systems,we suggest that the fluid-like behavior in the skin may be critical for mechanical adaptability.Understanding the influence of tissue fluidity may open pathways for modulating this process,potentially enhancing tissue expansion efficiency,reducing procedural duration,and improving clinical outcomes.This perspective highlights the importance of investigating the biological dynamics of tissue fluidity and exploring the potential for targeted manipulation of fluidity-related pathways to optimize tissue expansion.Such advancements could profoundly affect regenerative and reconstructive surgical practices.
基金Supported by the National Natural Science Foundation of China(U22B6004)Project of PetroChina Research Institute of Petroleum Exploration and Development(2022yjcq03)Core Technology Key Project of China Petroleum Changqing Oilfield Company(KJZX2023-01).
文摘In addition to the organic matter type,abundance,thermal maturity,and shale reservoir space,the preservation conditions of source rocks play a key factor in affecting the quantity and quality of retained hydrocarbons in source rocks of lacustrine shale,yet this aspect has received little attention.This paper,based on the case analysis,explores how preservation conditions influence the enrichment of mobile hydrocarbons in shale oil.Research showns that good preservation conditions play three key roles.(1)Ensure the retention of sufficient light hydrocarbons(C_(1)–C_(13)),medium hydrocarbons(C_(14)–C_(25))and small molecular aromatics(including 1–2 benzene rings)in the formation,which enhances the fluidity and flow of shale oil;(2)Maintain a high energy field(abnormally high pressure),thus facilitating the maximum outflow of shale oil;(3)Ensure that the retained hydrocarbons have the miscible flow condition of multi-component hydrocarbons(light hydrocarbons,medium hydrocarbons,heavy hydrocarbons,and heteroatomic compounds),so that the heavy hydrocarbons(C_(25+))and heavy components(non-hydrocarbons and asphaltenes)have improved fluidity and maximum flow capacity.In conclusion,in addition to the advantages of organic matter type,abundance,thermal maturity,and reservoir space,good preservation conditions of shale layers are essential for the formation of economically viable shale oil reservoirs,which should be incorporated into the evaluation criteria of shale oil-rich areas/segments and considered a necessary factor when selecting favorable exploration targets.
基金support from the National Natural Science Foundation of China(Nos.52031012,51904218)。
文摘A spiral fluidity test model of superalloys with 10 mm in height and 3 mm in thickness was designed to evaluate the fluidity of two distinct Ni-based superalloys IN718 and IN939.The factors influencing fluidity are ascertained through comparative analysis utilizing methodologies such as JMat Pro,differential scanning calorimetry and high-temperature confocal laser scanning microscopy.The results show that under identical testing conditions,the fluidity of the IN939 superalloy surpasses that of the IN718 superalloy.When subjected to the same temperature,the melt viscosity and surface tension of IN939 superalloy are considerably reduced relative to those of IN718 superalloy,which is beneficial to improving the melt fluidity.Furthermore,the liquidus temperature and solidification range for the IN939 superalloy are both smaller compared with those of the IN718 superalloy.This condition proves advantageous in delaying dendrite coherency,thereby improving fluidity.
基金supported by National Natural Science Foundation of China(Nos.52375394,52275390,52305429)Shanxi Scholarship Council of China(No.2021-125)+1 种基金Natural Science Foundation of Shanxi Province(No.20210302124631)Key Research and Development Program of Shanxi Province(Nos.202102050201011,2022ZDYF035).
文摘Mg-Zn-based alloys have been widely used in computer,communication,and consumer(3C)products due to excellent thermal conductivity.However,it is still a challenge to balance their mechanical performance and thermal conductivity.Here,we investigate microstructure,mechanical performance,thermal conductivity and metal fluidity of Mg-5Zn(wt.%)alloy after Cu alloying by experimental and simulation methods.First,Mg-5Zn alloy consist ofα-Mg matrix and interdendritic MgZn phases.As the Cu content increases,however,MgZn phases disappear but intragranular Mg_(2)Cu and interdendritic MgZnCu phases appear in Mg-5Zn-Cu alloys.Besides,the grain size ofα-Mg phase is refined and the volume fraction of MgZnCu phase increases as the Cu content increases.Second,Cu addition is found to improve thermal conductivity of Mg-5Zn alloy remarkably.Especially,Mg-5Zn-4Cu alloy exhibits the best thermal conductivity of 124 W/(m·K),which is mainly due to the significant reduction in both solid solubility of Zn in theα-Mg matrix and lattice distortion ofα-Mg matrix.Moreover,a stable crystal structure of MgZnCu phase also contributes to an increased thermal conductivity based on first principles and molecular dynamics simulations.Third,Cu addition simultaneously enhances strength and ductility of Mg-5Zn alloy.Tensile yield strength and elongation of Mg-5Zn-6Cu alloy reach 117 MPa and 18.0%,respectively,which is a combined result of refinement,solution,second phase,and dislocation strengthening.Finally,combined with a phase field simulation,we found that Cu addition enhances metal fluidity of Mg-5Zn alloy.On the one hand,Cu alloying not only delays dendrite growth but also prolongs solidification time.On the other hand,MgZnCu phase stabilizes the dendrite growth of theα-Mg phases by reducing energy consumption during solidification of liquid metal.This work demonstrates that Cu alloying is an ideal strategy for synergistically improving the thermal conductivity,mechanical performance and metal fluidity of Mg-based alloys.
基金supported by the National Natural Science Foundation of China(52171030)the National Key Research and Development Program of China(2018YFA0702903).
文摘Grain refinement is a satisfying method to enhance the comprehensive performance of Mg alloys,and using grain refiners to improve the quality of Mg castings has become a common practice in the current casting industry.In this study,the effects of Al-CeO_(2)-Mg grain refiner addition on microstructure,cast fluidity,and mechanical properties of AZ91 alloy were systemically investigated by OM,SEM,DSC,TEM,sand Archimedean spiral mold fluidity test,and tensile test.The results show that the Al-CeO_(2)-Mg grain refiner has a remarkable effect on as-cast AZ91 alloy including notable grain refinement,enhancement of cast fluidity,and improvement of tensile properties.The average grain size of AZ91 alloy is refined by 63%with 1.0wt.%Al-CeO_(2)-Mg grain refiner.Meanwhile,the casting flow length of the as-cast AZ91 alloy is increased from 332 mm to 440 mm.The improvement of cast fluidity is attributed to the decreased liquidus temperature,shortening of solid-liquid two-phase temperature range,and refinement of microstructure.
文摘H +_ATPase activity of tonoplast in roots of Hordeum vulgare L. cv. 'Tanyin 2' (salt_tolerant cultivar) increased when the roots were exposed to 50-200 mmol/L NaCl for 2 d, and decreased when NaCl concentration was increased to 600 mmol/L. In 'Kepin 7' (salt_sensitive cultivar), tonoplast H +_ATPase activity in roots also increased at lower levels of NaCl (50-100 mmol/L), but decreased at higher levels of NaCl (200-600 mmol/L). Tonoplast fluidity in roots of 'Tanyin 2' decreased at 50-200 mmol/L NaCl, and increased significantly at 600 mmol/L NaCl. Under salt stress, the change of tonoplast fluidity was identical with that of the ratio of unsaturated fatty acids to saturated fatty acids in tonoplast lipid of barley roots. It is proposed that the increase of tonoplast fluidity due to increased degree of unsaturation of fatty acids is one of the reasons leading to the decrease of H +_ATPase activity under higher level of NaCl stress.
文摘With in vitro spin labeling electron spin resonance (ESR) spectroscopy, we have studied the effects of Bu Yang Huan Wu (BYHW) decoction and its effective constituents such as astragaloside IV ferulic acid, chuanxiongzine, rutin, chlorogenic acid, 9,10 dimethoxy pterocarpane 7 O β D glucoside, calycosin, formononetin, calycosin 7 O glucoside, paeoniflorin, paeonal and quercein on the cell membrane fluidity of a rat brain which was modeled after the dual cervical arteries were intercepted and released for realizing an ischemia reperfusion injury which was selected as a brain stroke model. Our results indicated that the cell membrane fluidity in the model group decreased approximately 8% compared with the control group, and after brain cells were incubatied with species, the membrane fluidity could be recovered closely to the control level depending on the BYHW decoction and its different constituents. As the membrane fluidity is a very sensitive biological index which reflectsd the cell status, our method will be useful to study the molecular mechanism of tradition Chinese medicine (TCM) and its combination recipe.
基金Supported by a grant for young researcher from Ministry of Public Health of P.R.C.
文摘The main purpose of this study was to investigate the protective actions of captopril and cicaprost on changes of membrane fluidity of cultured neonatal rat myocardial cells exposed to anoxia and sugar deprivation.Lipid peroxidation level estimated by determining the thiobarbituric acid reactive substance(TBARS)content and lactate dehydrogenase(LDH)released in culture medium was also observed in order to examine other membrane-related changes due to anoxia.Membrane fluidity was monitored by measuring changes in the steady state fluorescence anisotropy(r_s)by fluorescence spectroscopy.The r_s value,TBARS level and LDH release were significantly increased after 3 h anoxia.Captopril(180 μmol/L),cicaprost(30 nmol/L)and indomethacin(1μmol/L)did not alter r_s, TBARS level and LDH activity of normal cultured neonatal rat myocardial cells.However,both captopril and cicaprost significantly prevented the increases of r_s,TBARS content and LDH release in those cells exposed to anoxia and sugar deprivation.lndomethacin abolished the actions of captopril on TBARS production and LDH release,but maintained its membrane fluidity protection.These results indicate that captopril and cicaprost protect membrane fluidity and lipid peroxidation changes in anoxia- injured myocardial cells.The action mechanism of captopril may be due,in part,to stimulation of prostacyclin synthesis and/or release.
基金Project(51722401)supported by the National Science Foundation for Excellent Young Scholars of ChinaProject(51334001)supported by the Key Program of National Natural Science Foundation of ChinaProject(FRF-TP-18-003C1)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Adding polypropylene(PP)fibers and coarse aggregates has become a popular way to enhance the strength and stability of the cemented tailings backfilling(CTB)body.It is essential to explore the influence of tailings-aggregate ratio and fiber content on the mechanical properties of CTB samples.The comprehensive tests of the unconfined compressive strength(UCS),slump and microstructure were designed,and the regression models were established to characterize the effect of the strength,ductility and fluidity.The results indicate that the tailings-aggregate ratio of 5:5 and PP fiber content of 0.5 kg/m^(3) are the optimum point considering the UCS,cracking strain,peak strain and post-peak ductility.The tailings-aggregate ratio is consistent with the unary quadratic to the UCS and a linear model with a negative slope to the slump.Microstructural analysis indicates that PP fiber tends to bridge the cracks and rod-mill sand to serve as the skeleton of the paste matrix,which can enhance the compactness and improve the ductility of the CTB.The results presented here are of great significance to the understanding and application of coarse aggregates and fibers to improve the mechanical properties of CTB.
文摘To investigate the thixotropic fluidities, microstructures and mechanical properties of semi-solid AZ91D magnesium alloy during reheating, a self-made die set with channels of different sizes were used. The results show that critical forming forces and maximal forming forces could be obtained and related to the holding times in the semi-solid forming process. In the holding time of 0-2700 s, with increasing the holding time, maximal forming force decreased sharply and critical forming force decreased slowly. In the whole thixotropic flowing process, the filling-in was steady and the surface fineness was good. The forming force increased when the slurry changed the flowing direction or flowed from the big-diameter chamber to the small-diameter one. The tensile strength and elongation to failure of the sample after holding time for 2700 s, compared to as-cast sample, are increased by approximately 42.7% and 180%, respectively, and the fractured surfaces presented dimple-like pattern.
基金supported by the National Natural Science Foundation of China(21878082).
文摘The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO ratios prepared on the basis of the range of oxide contents of Zhundong coal ash were investigated in this study. The results show that with the MgO/CaO ratio increase, the initial crystallization temperature increases, and the main temperature range of crystallization ratio growth moves to higher temperature range gradually which causes Tp25(Tp25is the temperature corresponding to the viscosity of 25 Pa·s)to increase. Mg-rich crystals are formed preferentially than Ca-rich crystals when adding the same amount of MgO and CaO during cooling. The effective slagging operating temperature range decrease from 217 ℃ for the slag with a 0:4 MgO/CaO ratio to 44 ℃ for the slag with a 4:0 MgO/CaO ratio with the MgO/CaO ratio increase. The slags with 2:2 and 1:3 MgO/CaO ratios show similar effective slagging operating temperature range, Tp25and the temperature corresponding to the viscosity of 2 Pa·s.However, compared with the slag with a 1:3 MgO/CaO ratio, the crystallization ratio and rate of slag with a 2:2 MgO/CaO ratio are lower within lower temperature range(1300–1200 ℃), causing its lower critical viscosity temperature and wider actual operating temperature range. Of the five slags, the widest effective slagging operating temperature range and the lowest Tp25of the slag with a 0:4 MgO/CaO ratio due to its low crystallization ratio, and wider actual operating temperature range of the slag with a 2:2 MgO/CaO ratio make the two slags suitable for slag discharge of EFB gasifier.
基金National Natural Science Foundation of China(Nos.51671166,51827801 and 51434008)Youth Fund of the Education Department in Hebei Province (QN2018305).
文摘Understanding the flow characteristics of amorphous metal melts is important for casting and molding processes.Fluidity of Zr-based amorphous metal melts was determined by using a self-designed apparatus.Phase analysis demonstrated that the fluidity test samples were fuUy amorphous structure.The onset crystallization temperature significantly moved toward high temperature with the increases of casting temperature,which improved the glass-forming ability and thermal stability of Zr-based amorphous metal.Fluidity test results demonstrated that the fluidity length increased monotonically with the increases of temperature,pressure,and runner diameter.By identifying the types and quantities of the defect in castings,it could conclude that smooth filling processes occurred under appropriate conditions.Experimental results indicated that the flow behavior of the Zr-based amorphous metal melts strongly depended on the casting temperature and equivalent thickness.Constitutive equation based on Newton's law of heat exchange and Rayleigh rule was established to'evaluate the fluidity of Zr-based amorphous metal melts.Theoretical calculations and experimental tests were basically coincided with each other.The determined optimal casting temperatures and equivalent thicknesses were adopted to successfully fabricate a series of fully shaped castings through gravity casting.
文摘The influence of ultrasonic degassing process on fluidity and hardness of secondary Al7Si0.3Mg alloy castings was studied by Weibull analysis. This work makes a contribution about fluidity and hardness distribution of secondary aluminum alloys with ultrasonic degassing phenomena using a two-parameter form of Weibull analysis. Results show that both hardness and fluidity of alloy are improved after the ultrasonic degassing process. Average efficiency of ultrasonic degassing on fluidity measurements is 31.71%, whereas on hardness values is 8.48%. The Brinell hardness of 45.7 and fluidity of 19.5 of Weibull modulus were achieved as the most reliable and reproducible after 45 s ultrasonic degassing process against 15 s and 30 s ultrasonic degassing processes. The value of 70.08 HB is obtained from ultrosonic degassing, which is equivalent to sand casting of primary Al7Si0.3Mg aluminum alloy, and the highest value of 56.4 cm for 45 s after ultrasonic degassing of fluidity was measured.
基金supported by the Doctor Foundation(2008) in Shanxi Datong University
文摘After bilateral carotid artery occlusion for 30 minutes and reperfusion for 2 hours, distinct pathological changes presented in the cerebral cortex and cerebellum of rats. Compared with normal rats, nerve cell membrane fluidity significantly decreased in ischemia/reperfusion rats as detected by spin-labeling electron spin resonance, consistent with order parameter S and rotational correlation time TC measurements. Brain nerve cells from rats with ischemia/reperfusion injury were cultured with 1-100 mg/mL Buyang Huanwu decoction. Results showed that Buyang Huanwu decoction gradually increased membrane fluidity dose-dependently to normal levels, and eliminated hydroxide （OH＇） and superoxide （O2＇） free radicals dose-dependenUy. These findings suggest that Buyang Huanwu decoction can protect against cell membrane fluidity changes in rats with ischemia/ reperfusion injury by scavenging free radicals.
基金supported by the National Basic Research Program of China(2012CB114103)
文摘Differential effects of methamidophos and three pyrethroids on ATPase activity and membrane fluidity of mitochondria were investigated between the wolf spider（Pirata subpiraticus（Boes.et Str.））and the rice stem borer（Chilo suppressalis（Walker））.Based on a comparison of LD_（50） values,the toxicities of the tested insecticides were higher to the wolf spider than to the rice stem borer.Cyhalothrin at 1×10^（–4） mmol L^（–1） caused inhibition of the mitochondrial Na~＋-K~＋-ATPase and Ca^（2＋）-Mg^（2＋）-ATPase activities,and it’s inhibitions on Na＋-K＋-ATPase and Ca^（2＋）-Mg^（2＋）-ATPase activities were significantly higher in the wolf spider（44 and 28%）than in the rice stem borer（19 and 11%）.Methamidophos at 1×10^（–4） mmol L^（–1） decreased Ca^（2＋）-Mg^（2＋）-ATPase activity by 16 and 27%in the wolf spider and the rice stem borer,respectively,but no significant effect on the specific activity of Na＋-K＋-ATPase was observed.The DPH（1,6-diphenyl-1,3,5-hexatriene）fluorescence polarization values of mitochondrial membranes were not significantly affected by methamidophos in either species.However,cyhalothrin and alpha-cypermethrin induced the values of DPH polarization of mitochondrial membrane increasing with the concentration of cyhalothrin and alpha-cypermethrin from 20 to 100μmol L^（–1） in the rice stem borer and the wolf spider.Effect of ethofenprox on fluidity of the wolf spider and the rice stem borer was contrary.These results suggest that both inhibition of membrane ATPase and changes of membrane fluidity could be appended to the action mechanisms of pyrethroid insecticides.
基金Project (No. 30470198) supported by the National Natural Science Foundation of China
文摘Objective:To evaluate effects of epigallocatechin-3-gallate (EGCG) on the viability, membrane properties, and zinc distribution, with and without the presence of Zn2+, in human prostate carcinoma LNCaP cells. Methods: We examined changes in cellular morphology and membrane fluidity of LNCaP cells, distribution of cellular zinc, and the incorporated portion of EGCG after treatments with EGCG, Zn2+, and EGCG+Zn2+. Results: We observed an alteration in cellular morphology and a decrease in membrane fluidity of LNCaP cells after treatment with EGCG or Zn2+. The proportion of EGCG incorporated into liposomes treated with the mixture of EGCG and Zn2+ at the ratio of 1:1 was 90.57%, which was significantly higher than that treated with EGCG alone (30.33%). Electron spin resonance (ESR) studies and determination of fatty acids showed that the effects of EGCG on the membrane fluidity of LNCaP were decreased by Zn2+. EGCG accelerated the accumulation of zinc in the mitochondria and cytosol as observed by atomic absorption spectrometer. Conclusion: These results show that EGCG interacted with cell membrane, decreased the membrane fluidity of LNCaP cells, and accelerated zinc accumulation in the mitochondria and cytosol, which could be the mechanism by which EGCG inhibits proliferation of LNCaP cells. In addition, high concentrations of Zn2+ could attenuate the actions elicited by EGCG.
基金Funded by the Natural Science Foundation of China(51808369)the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(18KJB560016)+4 种基金the Opening Project of State Key Laboratory of Green Building Materials(YA-615)the State Key Laboratory of Silicate Building Materials(SYSJJ2018-09)Hubei Key Laboratory of Water System Science for Sponge City Construction(2019-01)the Construction System Science and Technology Project of Jiangsu Province(2018ZD049)the Natural Science Foundation of Suzhou University of Science and Technology(XKQ2018009)。
文摘Effects of organosilane-modified PCE (OS-PCE) on the fluidity and the hydration properties of cement-fly ash (FA) composite binder were systematically analyzed.The experimental results show that OS-PCE possesses respectively 36.98% and 36.67% higher saturated adsorption amount on cement and FA,in comparison with ordinary PCE,and can contribute to higher fluidity of cement-FA composite binder.The addition of OS-PCE retards hydration process of cement-FA composite binder proportionally with the dosage of OS-PCE,but promotes the hydration kinetics of the composite binder.The reactivity enhancement is attributed to the well-dispersed FA by OS-PCE,which provides more nucleation sites for the reaction of heterogeneous C-S-H and enhances the contact with water to react with CH forming pozzolanic C-S-H.Well-distributed hydration products are exhibited in the hardened binder added with OS-PCE,with a large number of hydrated gels uniformly fill in the pores and gaps,which improves the compaction of the hardened structure.
