This study investigates the enhancement of convective heat transfer in a serpentine pipe using ferrofluid flow influenced by dual non-uniform magnetic sources.The primary objective is to improve thermal performance in...This study investigates the enhancement of convective heat transfer in a serpentine pipe using ferrofluid flow influenced by dual non-uniform magnetic sources.The primary objective is to improve thermal performance in compact cooling systems,such as those used in heat exchangers.A two-dimensional,steady-state Computational Fluid Dynamic(CFD)model is developed in ANSYS Fluent to simulate the behavior of an incompressible ferrofluid under applied constant heat flux and magnetic fields.The magnetic force is modeled using the Kelvin force,which acts on magnetized nanoparticles in response to spatially varying electromagnetic fields generated by two strategically positioned current-carrying wires.The effects of magnetic field strength,quantified by the magnetic number(Mn),on flow behavior and temperature distribution are thoroughly analyzed.The results indicate that increasing Mn leads to higher Nusselt numbers,demonstrating enhanced convective heat transfer.Secondary vortices induced by magnetic forcing improve fluid mixing,particularly in curved regions of the pipe.A mesh-independence study and model validation with benchmark data support the reliability of the numerical framework.This work highlights the potential of magnetic-field-assisted thermal control in energy-efficient cooling applications and provides a foundation for the further development of advanced ferrofluid-based heat transfer systems.展开更多
The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to...The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.展开更多
Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numer...Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numerically investigate the reaction process of hydrocarbon-containing VOCs in RCO using computational fluid dynamics(CFD)simulation.To obtain the conversion characteristics of multi-component hydrocarbons,the effects of intake load,equivalence ratio,and the composition of multi-component hydrocarbons on the flow,heat transfer,and conversion rate of the reactor were analyzed.A feasibility study plan targeting the hard-to-convert components was also proposed.The results indicated that as the load increases,the conversion rates of the various components decrease,while the reaction rates increase.Moreover,increasing the flow velocity intensifies turbulence and enhances the collision frequency between the gas and the wall surfaces.This,in turn,amplifies the resistance effect of the porous medium.As the equivalence ratio of VOCs to oxygen increases,the oxygen-deficient condition leads to a decrease in the molecular weight of the hydrocarbons involved in the reaction.The reaction temperature also shows a downward trend.A comparative analysis of the catalytic combustion characteristics of multi-component VOCs and single-component gases reveals that adding ethane and propane can facilitate methane oxidation.展开更多
Van der Waals(vdW)heterostructures have attracted much attention due to their distinctive optical,electrical,and thermal properties,demonstrating promising potential in areas such as photocatalysis,ultrafast photonics...Van der Waals(vdW)heterostructures have attracted much attention due to their distinctive optical,electrical,and thermal properties,demonstrating promising potential in areas such as photocatalysis,ultrafast photonics,and free electron radiation devices.Particularly,they are promising platforms for studying thermionic emission.It is illustrated that using vdW heterostructure-based thermionic emission can enhance heat transfer in vacuum devices.As a proof of concept,the approach is demonstrated to offer a promising solution for the long-standing overheating issue in X-ray tubes.Specifically,it is shown that the saturated target temperature of a 2000 W X-ray tube can be reduced from around 1200℃ to 490℃.Additionally,it is also demonstrated that by reducing the height of the Schottky barrier formed in the vdW heterostructures,the thermionic cooling performance can be enhanced.The findings pave the way for the development of high-power X-ray tubes.展开更多
In response to the actual demands of the energy storage type organic Rankine power generation cycle,this study proposes a new type of jacketed shell and tube heat exchanger with integrated cold storage and heat exchan...In response to the actual demands of the energy storage type organic Rankine power generation cycle,this study proposes a new type of jacketed shell and tube heat exchanger with integrated cold storage and heat exchange.N-tedecane is selected as the phase change material for cold storage,low-temperature water as the cold source,and R134a as the heat source.The phase change material for cold storage is filled inside the jacket tube of the heat exchanger.Cold fluid is introduced into the inner tube to cause the phase change material to condense and store cold.After the cold storage is completed,R134a flows in from the shell side and condenses through heat exchange with the solidified phase change material for energy storage.This study discusses the influence laws of different cold water mass flow rates and temperatures on the cold storage performance of this heat exchanger,and analyzes the condensation effect of R134a.The results show that when the mass flow rate is 0.5 kg/s and the cold water temperature is between 3 and 4℃,the average power of the energy storage heat exchanger in the condensation experiment is 80W,and the average convective heat transfer coefficient is 110.73 W/(m^(2)⋅K).This research provides an experimental basis for the development of energy storage organic Rankine power generation cycles.展开更多
The radiative heat flux of the plume from reusable rockets is a critical parameter during the launch and return processes.This paper proposes a method for calculating radiative heat flux with higher accuracy than prev...The radiative heat flux of the plume from reusable rockets is a critical parameter during the launch and return processes.This paper proposes a method for calculating radiative heat flux with higher accuracy than previously reported for a recoverable nine-engine liquid-propellant rocket.Based on the Radiative Transfer Equation(RTE),this study employs the discrete transfer method to solve the transient RTE problem using physical properties to describe the problem while avoiding the need to directly solve mathematical equations.The proposed method can effectively determine the radiative heat flux of the flow field and is applicable to problems involving various geometries.Calculations reveal that during the ascent phase of the rocket,the radiative heat flux at the base of the vehicle reaches its maximum in the initial stages of the lift-off,reaching a maximum of~50 kW/m^(2),which is 2.24 times the maximum value during the return phase.During the deceleration stage of re-entry into the atmosphere,the maximum radiative heat flux recorded on the sidewall of the rocket is 29.1 kW/m^(2);the maximum heat flux on the bottom surface is approximately 22.3 kW/m^(2),accounting for 76.6%of that on the rocket's sidewall.This provides a basis for the thermal protection design of the rocket's bottom and walls as well as for the thermal management of cryogenic propellant tanks.Future research will involve ground engine testing and flight experiments to further validate the proposed model.展开更多
To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mat...To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mathematics models of aluminum holding furnace in the premixed combustion processing were established based on mass conservation,moment conservation,momentum conservation,energy conservation and chemistry species conservation.Computational results agree well with the test data of the typical condition.The maximum combustion temperature is 1 850 K.The average temperature of the molten aluminum is 1 158 K,and the maximum temperature difference is about 240 K.The average temperature increases 0.3 ℃ while the temperature of combustion air increases 1 ℃.The optimal excess air ratio is 1.25-1.30.展开更多
The overall heat transfer coefficient(OHTC)of rock fractures is a fundamental parameter for characterizing the heat transfer behavior of rock fractures in hot dry rock(HDR)geothermal mining.Although a number of practi...The overall heat transfer coefficient(OHTC)of rock fractures is a fundamental parameter for characterizing the heat transfer behavior of rock fractures in hot dry rock(HDR)geothermal mining.Although a number of practical formulae for heat transfer coefficients have been developed in the literature,there is still no widely accepted analytical solution.This paper constructs highly accurate analytical solutions for the temperatures of the inner fracture wall and the fluid.Then they are employed to develop new definition-based formulae(formula A and its simplification formula B)of the OHTC,which are well validated by the experimental and numerical simulation results.An empirical correlation formula of heat transfer coefficient is proposed based on the definition-based formulae which can be directly used in the numerical simulations of heat transfer in rock fractures.A site-scale application example of numerical simulation also demonstrates the effectiveness of the empirical correlation formula.展开更多
Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; theref...Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.展开更多
Due to the complex high-temperature characteristics of hydrocarbon fuel,the research on the long-term working process of parallel channel structure under variable working conditions,especially under high heat-mass rat...Due to the complex high-temperature characteristics of hydrocarbon fuel,the research on the long-term working process of parallel channel structure under variable working conditions,especially under high heat-mass ratio,has not been systematically carried out.In this paper,the heat transfer and flow characteristics of related high temperature fuels are studied by using typical engine parallel channel structure.Through numeri⁃cal simulation and systematic experimental verification,the flow and heat transfer characteristics of parallel chan⁃nels under typical working conditions are obtained,and the effectiveness of high-precision calculation method is preliminarily established.It is known that the stable time required for hot start of regenerative cooling engine is about 50 s,and the flow resistance of parallel channel structure first increases and then decreases with the in⁃crease of equivalence ratio(The following equivalence ratio is expressed byΦ),and there is a flow resistance peak in the range ofΦ=0.5~0.8.This is mainly caused by the coupling effect of high temperature physical proper⁃ties,flow rate and pressure of fuel in parallel channels.At the same time,the cooling and heat transfer character⁃istics of parallel channels under some conditions of high heat-mass ratio are obtained,and the main factors affect⁃ing the heat transfer of parallel channels such as improving surface roughness and strengthening heat transfer are mastered.In the experiment,whenΦis less than 0.9,the phenomenon of local heat transfer enhancement and deterioration can be obviously observed,and the temperature rise of local structures exceeds 200℃,which is the risk of structural damage.Therefore,the reliability of long-term parallel channel structure under the condition of high heat-mass ratio should be fully considered in structural design.展开更多
As the dominant seepage channel in rock masses,it is of great significance to study the influence of fracture roughness distribution on seepage and heat transfer in rock masses.In this paper,the fracture roughness dis...As the dominant seepage channel in rock masses,it is of great significance to study the influence of fracture roughness distribution on seepage and heat transfer in rock masses.In this paper,the fracture roughness distribution functions of the Bakhtiary dam site and Oskarshamn/Forsmark mountain were fitted using statistical methods.The COMSOL Multiphysics finite element software was utilized to analyze the effects of fracture roughness distribution types and empirical formulas for fracture hydraulic aperture on the seepage field and temperature field of rock masses.The results show that:(1)The fracture roughness at the Bakhtiary dam site and Oskarshamn/Forsmark mountain follows lognormal and normal distributions,respectively;(2)For rock masses with the same expected value and standard deviation of fracture roughness,the outflow from rock masses with lognormal distribution of fracture roughness is significantly larger than that of rock masses with normal distribution of fracture roughness;(3)The fracture hydraulic aperture,outflow,and cold front distance of the Li and Jiang model are significantly larger than those of the Barton model;(4)The outflow,hydraulic pressure distribution,and temperature distribution of the Barton model are more sensitive to the fracture roughness distribution type than those of the Li and Jiang model.展开更多
The use of nanofluids as heat transfer media represents an innovative strategy to enhance heat transfer performances.This study investigates experimentally the turbulent convective heat transfer characteristics of wat...The use of nanofluids as heat transfer media represents an innovative strategy to enhance heat transfer performances.This study investigates experimentally the turbulent convective heat transfer characteristics of waterbased nanofluids containing TiO_(2),CuO,and graphene nanoplatelet(GNP)nanoparticles as they flow through a copper tube.Both the dynamic viscosity and thermal conductivity of these nanofluids were modeled and experimentally measured across varying nanoparticle concentrations(0.01,0.02,and 0.03 vol.%)and temperatures(25℃,35℃,and 45℃).The findings indicate that the behavior of nanofluids depends on the parameter used for comparison with the base fluid.Notably,both the friction factor and heat transfer coefficient increase with higher nanoparticle volume concentrations at a constant Reynolds number.The results further reveal that the GNP/water nanofluid,with a volume concentration of 0.03%at 45℃,exhibit the highest Nusselt number,followed by the CuO/water and TiO_(2)/water nanofluids,with respective increases of 17.8%,11.09%,and 8.11%.展开更多
The growing need for enhanced heat dissipation is compelling the development of more effective heat exchangers.Innovation inspired by nature bionics,four types of leaf-shaped pin fins were proposed and four combinatio...The growing need for enhanced heat dissipation is compelling the development of more effective heat exchangers.Innovation inspired by nature bionics,four types of leaf-shaped pin fins were proposed and four combinations of them were considered.The leaf-shaped design of the cooling pin fin enhances uniformity and synergy,effectively creating an optimized flow path that boosts cooling performance.Eight three-dimensional conjugate heat transfer models in staggered arrangement were developed using ANSYS-Fluent software.Aluminum6061material was used as the heat sinkmaterial and single-phase liquid water flowed through the rectangular channel where the Reynolds(R_(e))number varies from 40 to 100.Using the same boundary conditions as the software simulations,two leaf-shaped channels were printed to validate numerical models.Velocity field and temperature differences of the eight proposed leaf-shaped pin fins configurations were discussed by comparison with cylindrical pin fins.Based on the findings of this study,at a Reynolds number of 80,the Leaf B Staggered Array(LBSA)records a maximum temperature that is 0.72 K lower than that of the cylindrical pin fins arrangement.Additionally,the LBSA exhibits a reduction in the friction factor by approximately 33.3%relative to the circular pin fins array under the same R_(e).This implies that the design of LBSA has been optimized to provide better heat dissipation performance while maintaining lower energy consumption.Furthermore,the LBSA demonstrates the most favorable thermal-hydraulic performance index(TPI),which is 1.18 times higher than that of the circular pin fins arrangement at R_(e)=80.The temperature reduction and friction factor reduction of the lobed channel is more pronounced than that of the conventional cooling channel,highlighting its potential to increase heat transfer efficiency and reduce energy consumption in practical applications.展开更多
The latent heat thermal energy storage system with solid-liquid phase-change material(SLPCM-LHTES)as energy storage medium provides outstanding advantages such as system simplicity,stable temperature control,and high ...The latent heat thermal energy storage system with solid-liquid phase-change material(SLPCM-LHTES)as energy storage medium provides outstanding advantages such as system simplicity,stable temperature control,and high energy storage density,showing great potential toward addressing the energy storage problems associated with decentralized,intermittent,and unstable renewable energy sources.Notably,effective heat transfer within the SLPCM-LHTES is crucial for extending its application potential.Therefore,a comprehensive understanding of the heat transfer processes in SLPCM-LHTES from a theoretical perspective is necessary.In this review,we propose a three-stage heat transfer pathway in SLPCM-LHTES,including external heating,interfacial heat transfer,and intrinsic phase transition processes.From the perspective of this three-stage pathway,the theoretical basis of heat transfer processes and typical efficiency enhancement strategies in SLPCM-LHTES are summarized.Moreover,an overview of the typical applications of SLPCM-LHTES in various fields,such as building energy efficiency,textiles and garments,and battery thermal management,is presented.Finally,the remaining challenges and possible avenues of research in this burgeoning field will also be discussed.展开更多
Plate heat exchangers suffer from significant energy losses,which adversely affect the overall efficiency of thermal systems.To address this challenge,various heat transfer enhancement techniques have been investigate...Plate heat exchangers suffer from significant energy losses,which adversely affect the overall efficiency of thermal systems.To address this challenge,various heat transfer enhancement techniques have been investigated.Notably,the incorporation of surface corrugations is widely recognized as both effective and practical.Chevron corrugation is the most employed design.However,there remains a need to investigate alternative geometries that may offer superior performance.This study aims to find a novel corrugation design by conducting a comparative CFD analysis of flat,square,chevron,and cylindrical corrugated surfaces,assessing their impact on heat transfer enhancement within a plate heat exchanger.ANSYS Fluent software was used for simulation at four distinct Reynolds numbers(10,000,18,000,26,000,and 28,000),with a heat flux of 12,000 W/m^(2).A structured mesh was generated using Pointwise software.The material of the solid plates was modelled as aluminum,the fluid was modelled as water,and the flow was turbulent.To obtain a fully developed turbulent flow,a separate inlet duct was modelled,and the output velocity profile of the inlet duct was input into the plate heat exchanger.The Nusselt number(Nu)and heattransfer coefficient(h)were calculated to evaluate the performance of all surfaces.The results indicate that cylindrical corrugated surfaces exhibit higher Nusselt numbers than chevron,square,and flat plates.This higher performance is because of the generation of vortices in the middle of the cylindrical texture.Consequently,flow recirculation occurs,leading to reattachment to the mainstreamflow.This phenomenon induces increased turbulence,thereby enhancing the heat transfer efficiency.To validate the results,a grid-convergence independence test was performed for three different mesh sizes.In addition,empirical calculations were performed using the Dittus-Boelter and the Genilaski equations to validate the results of the flat-plate heat exchanger.It was concluded that the cylinder was the best corrugated surface and had a maximum heat transfer 35%higher than that of a flat plate.展开更多
The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation secti...The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation section paired with superhydrophilic,superhydrophobic,and hybrid condensation section).The Volume of Fluid(VOF)model was utilized to capture the phase-change process within the PHPs.The study also evaluated the influence of surface wettability on fluid patterns and thermo-dynamic heat transfer performance under various heat fluxes.The results indicated that the effective nucleation and detachment of droplets are critical factors influencing the thermal performance of the PHPs.The overall heat transfer performance of the superhydrophobic surface was significantly improved at low heat flux.Under medium to high heat flux,the superhydrophilic condensation section exhibits a strong oscillation effect and leads to the thickening of the liquid film.In addition,the hybrid surface possesses the heat transfer characteristics of both superhydrophilic and superhydrophobic walls.The hybrid condensation section exhibited the lowest thermal resistance by 0.45 K/W at the heat flux of 10731 W/m^(2).The thermal resistance is reduced by 13.1%and 5.4%,respectively,compared to the superhydrophobic and superhydrophilic conditions.The proposed surface-modification method for achieving highly efficient condensation heat transfer is helpful for the design and operation of device-cooling components.展开更多
The pivotal role microchannels play in the thermal management of electronic components has,in recent decades,prompted extensive research into methods for enhancing their heat transfer performance.Among these methods,s...The pivotal role microchannels play in the thermal management of electronic components has,in recent decades,prompted extensive research into methods for enhancing their heat transfer performance.Among these methods,surface wettability modification was found to be highly effective owing to its significant influence on boiling dynamics and heat transfer mechanisms.In this study,we modified surface wettability using a nanocomposite coating composed of graphene nano plate(GNPs)and multi-walled carbon nanotubes(MWCNT)and then examined how the modification affected the transfer of boiling heat in microchannels.The resultant heat transfer coefficients for hydrophilic and hydrophilic composite(GNPs+MWCNT)microchannels were,respectively,42.8%and 33.95%higher compared with that of the uncoated surface.These results verify that hydrophilic GNP-based coating significantly improves boiling heat transfer performance.It was observed that a minor increase in contact angle,θfrom 73.142°to 75.73°,resulted in a noticeable decrease in thermal performance.This is attributed to diminished liquid film stability,reduced nucleation site activity,and weakened capillary-driven liquid replenishment.These findings underscore the crucial role of optimized surface wettability in maintaining efficient microchannel boiling.At high mass flux,the GNPS microchannels exhibited maximum pressure drop values,with a pressure drop ratio as high as 36%compared to 29%for the GNPs+MWCNT composite samples.Nevertheless,when a composite hydrophilic–hydrophobic coating was deposited through electrodeposition,the enhancement in heat transfer was less significant.This was probably due to decreased surface uniformity,diminished liquid film stability,and the disruption of effective nucleation behavior,all associated with the slight increase in surface contact angle.The obtained results can be used as guidance for designing advanced cooling surfaces in high-performance microelectronic and energy systems,where precise control of surface characteristics is critical.展开更多
In exploring hypersonic propulsion,precooler combined engines require the development of lightweight,efficient,and compact heat exchangers(HX).As additive manufacturing technology continues to progress,triply periodic...In exploring hypersonic propulsion,precooler combined engines require the development of lightweight,efficient,and compact heat exchangers(HX).As additive manufacturing technology continues to progress,triply periodic minimal surface(TPMS)structures,characterized by exceptionally high surface area to volume ratios and intricate geometric structures,have demonstrated superior heat transfer performance.This research examines the thermal-hydraulic(TH)behavior of FKS and Diamond as heat transfer structures under different Reynolds numbers through numerical simulations.The Nusselt number for FKS is 13.2%–17.6%higher than Diamond,while the friction factor for FKS is approximately 18.8%–29.3%higher.A detailed analysis of the internal flow mechanisms reveals that the flow pattern within TPMS can be summarized as cyclic convergence-separation-convergence.The fluid experiences constant disturbances from the structure in all spatial directions,generating strong turbulent mixing and large wall shear stresses,which significantly enhance heat transfer performance.展开更多
Freeze-drying of structurally heterogeneous biomaterials such as porcine aorta presents considerable modeling challenges due to their inherent multilayer composition and moving sublimation interfaces.Conventional mode...Freeze-drying of structurally heterogeneous biomaterials such as porcine aorta presents considerable modeling challenges due to their inherent multilayer composition and moving sublimation interfaces.Conventional models often overlook structural anisotropy and dynamic boundary progression,while experimental determination of key parameters under cryogenic conditions remains difficult.To address these,this study develops a heat and mass transfer model incorporating a dynamic node strategy for the sublimation interface,which effectively handles continuous computational domain deformation.Additionally,specialized fixed nodes were incorporated to adapt to the multilayer structure and its spatially varying thermophysical properties.A novel non-contact gravimetric system was introduced to monitor mass loss in real time without disrupting vacuum,enabling accurate experimental validation.Combined with dehydration data,the model quantified critical parameters including effective thermal conductivity of the dried layer,vapor diffusivity,and sublimation mass transfer resistance.The results show that the migration of the sublimation fronts from both the inner and outer tunics toward the tunica media significantly alters the drying kinetics and heat-mass transfer characteristics.The proposed approach provides an adaptable and predictive framework for simulating freeze-drying processes in structurally heterogeneous systems with spatially varying thermophysical properties.展开更多
The heat transfer coefficient of the water surface is an important parameter in the design of thermal discharge in nuclear power plant engineering.In this study,in situ observations were performed in the northwestern ...The heat transfer coefficient of the water surface is an important parameter in the design of thermal discharge in nuclear power plant engineering.In this study,in situ observations were performed in the northwestern South China Sea near a coastal nuclear power plant to evaluate the applicability of heat transfer coefficient calculation algorithms commonly used in marine thermal discharge engineering in China.The results show that the Regulation for Hydraulic and Thermal Model in Cooling Water Projects(SL 160-2012)is not applicable in calculating the heat transfer coefficient in offshore areas.SL 160-2012 significantly overestimates the heat loss at the sea surface.However,Code for Design of Cooling for Industrial Recirculating Water(GB/T 50102-2014)performs well,and its estimation coefficient is roughly consistent with the estimations of the COARE 3.6 bulk algorithm,which is extensively used in physical oceanography for calculating air-sea heat fluxes,and the Gunneberg formula.In a 3-day observation,the average heat transfer coefficients estimated using these three algorithms were 50.4,48.5,and 48.8 W m^(-2)℃^(-1),respectively,with a deviation of less than 4% among them,whereas that estimated using SL 160-2012 was as high as 176.3 W m^(-2)℃^(-1).The abnormally large value of SL 160-2012 is due to its additional cooling term,which is artificially increased by 100 times because of the incorrect unit conversion used when developing the regulation.If this error is corrected,the value will decrease to 50.5 W m^(-2)℃^(-1),which is very close to the estimation of GB/T 50102-2014.展开更多
文摘This study investigates the enhancement of convective heat transfer in a serpentine pipe using ferrofluid flow influenced by dual non-uniform magnetic sources.The primary objective is to improve thermal performance in compact cooling systems,such as those used in heat exchangers.A two-dimensional,steady-state Computational Fluid Dynamic(CFD)model is developed in ANSYS Fluent to simulate the behavior of an incompressible ferrofluid under applied constant heat flux and magnetic fields.The magnetic force is modeled using the Kelvin force,which acts on magnetized nanoparticles in response to spatially varying electromagnetic fields generated by two strategically positioned current-carrying wires.The effects of magnetic field strength,quantified by the magnetic number(Mn),on flow behavior and temperature distribution are thoroughly analyzed.The results indicate that increasing Mn leads to higher Nusselt numbers,demonstrating enhanced convective heat transfer.Secondary vortices induced by magnetic forcing improve fluid mixing,particularly in curved regions of the pipe.A mesh-independence study and model validation with benchmark data support the reliability of the numerical framework.This work highlights the potential of magnetic-field-assisted thermal control in energy-efficient cooling applications and provides a foundation for the further development of advanced ferrofluid-based heat transfer systems.
基金supported by the Tianjin Education Commission Research Program Project(No.2024KJ105)。
文摘The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.
基金supported by National Key Research&Development Program of China(2022YFB4101500).
文摘Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numerically investigate the reaction process of hydrocarbon-containing VOCs in RCO using computational fluid dynamics(CFD)simulation.To obtain the conversion characteristics of multi-component hydrocarbons,the effects of intake load,equivalence ratio,and the composition of multi-component hydrocarbons on the flow,heat transfer,and conversion rate of the reactor were analyzed.A feasibility study plan targeting the hard-to-convert components was also proposed.The results indicated that as the load increases,the conversion rates of the various components decrease,while the reaction rates increase.Moreover,increasing the flow velocity intensifies turbulence and enhances the collision frequency between the gas and the wall surfaces.This,in turn,amplifies the resistance effect of the porous medium.As the equivalence ratio of VOCs to oxygen increases,the oxygen-deficient condition leads to a decrease in the molecular weight of the hydrocarbons involved in the reaction.The reaction temperature also shows a downward trend.A comparative analysis of the catalytic combustion characteristics of multi-component VOCs and single-component gases reveals that adding ethane and propane can facilitate methane oxidation.
基金supported by National Natural Science Foundation of China(61921002 and 92163204)。
文摘Van der Waals(vdW)heterostructures have attracted much attention due to their distinctive optical,electrical,and thermal properties,demonstrating promising potential in areas such as photocatalysis,ultrafast photonics,and free electron radiation devices.Particularly,they are promising platforms for studying thermionic emission.It is illustrated that using vdW heterostructure-based thermionic emission can enhance heat transfer in vacuum devices.As a proof of concept,the approach is demonstrated to offer a promising solution for the long-standing overheating issue in X-ray tubes.Specifically,it is shown that the saturated target temperature of a 2000 W X-ray tube can be reduced from around 1200℃ to 490℃.Additionally,it is also demonstrated that by reducing the height of the Schottky barrier formed in the vdW heterostructures,the thermionic cooling performance can be enhanced.The findings pave the way for the development of high-power X-ray tubes.
基金the the basic scientific research Funds project of Heilongjiang Universities[grant numbers 2024-KYYWF-0554].
文摘In response to the actual demands of the energy storage type organic Rankine power generation cycle,this study proposes a new type of jacketed shell and tube heat exchanger with integrated cold storage and heat exchange.N-tedecane is selected as the phase change material for cold storage,low-temperature water as the cold source,and R134a as the heat source.The phase change material for cold storage is filled inside the jacket tube of the heat exchanger.Cold fluid is introduced into the inner tube to cause the phase change material to condense and store cold.After the cold storage is completed,R134a flows in from the shell side and condenses through heat exchange with the solidified phase change material for energy storage.This study discusses the influence laws of different cold water mass flow rates and temperatures on the cold storage performance of this heat exchanger,and analyzes the condensation effect of R134a.The results show that when the mass flow rate is 0.5 kg/s and the cold water temperature is between 3 and 4℃,the average power of the energy storage heat exchanger in the condensation experiment is 80W,and the average convective heat transfer coefficient is 110.73 W/(m^(2)⋅K).This research provides an experimental basis for the development of energy storage organic Rankine power generation cycles.
文摘The radiative heat flux of the plume from reusable rockets is a critical parameter during the launch and return processes.This paper proposes a method for calculating radiative heat flux with higher accuracy than previously reported for a recoverable nine-engine liquid-propellant rocket.Based on the Radiative Transfer Equation(RTE),this study employs the discrete transfer method to solve the transient RTE problem using physical properties to describe the problem while avoiding the need to directly solve mathematical equations.The proposed method can effectively determine the radiative heat flux of the flow field and is applicable to problems involving various geometries.Calculations reveal that during the ascent phase of the rocket,the radiative heat flux at the base of the vehicle reaches its maximum in the initial stages of the lift-off,reaching a maximum of~50 kW/m^(2),which is 2.24 times the maximum value during the return phase.During the deceleration stage of re-entry into the atmosphere,the maximum radiative heat flux recorded on the sidewall of the rocket is 29.1 kW/m^(2);the maximum heat flux on the bottom surface is approximately 22.3 kW/m^(2),accounting for 76.6%of that on the rocket's sidewall.This provides a basis for the thermal protection design of the rocket's bottom and walls as well as for the thermal management of cryogenic propellant tanks.Future research will involve ground engine testing and flight experiments to further validate the proposed model.
基金Project(2006AA03Z523) supported by the National High-Tech Research and Development Program of ChinaProject(08C26224302178) supported by the Innovation Foundation of Central South University,China
文摘To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mathematics models of aluminum holding furnace in the premixed combustion processing were established based on mass conservation,moment conservation,momentum conservation,energy conservation and chemistry species conservation.Computational results agree well with the test data of the typical condition.The maximum combustion temperature is 1 850 K.The average temperature of the molten aluminum is 1 158 K,and the maximum temperature difference is about 240 K.The average temperature increases 0.3 ℃ while the temperature of combustion air increases 1 ℃.The optimal excess air ratio is 1.25-1.30.
基金support of this work by the National Natural Science Foundation of China (Grant Nos.41972316 and 41672252).
文摘The overall heat transfer coefficient(OHTC)of rock fractures is a fundamental parameter for characterizing the heat transfer behavior of rock fractures in hot dry rock(HDR)geothermal mining.Although a number of practical formulae for heat transfer coefficients have been developed in the literature,there is still no widely accepted analytical solution.This paper constructs highly accurate analytical solutions for the temperatures of the inner fracture wall and the fluid.Then they are employed to develop new definition-based formulae(formula A and its simplification formula B)of the OHTC,which are well validated by the experimental and numerical simulation results.An empirical correlation formula of heat transfer coefficient is proposed based on the definition-based formulae which can be directly used in the numerical simulations of heat transfer in rock fractures.A site-scale application example of numerical simulation also demonstrates the effectiveness of the empirical correlation formula.
基金National Natural Science Foundation of China(Grant No.U1510131)Key Research and Development Projects of Shanxi Province of China(Grant Nos.201603D121010,201603D111004)+3 种基金Science and Technology Project of Jin Cheng City of China(Grant No.20155010)Youth Program of National Natural Science Fund of China(Grant No.51604181)Project of Young Scholar of Shanxi ProvinceLeading Talent Project of Innovative Entrepreneurial Team of Jiangsu Province(Grant No.51501122)
文摘Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.
文摘Due to the complex high-temperature characteristics of hydrocarbon fuel,the research on the long-term working process of parallel channel structure under variable working conditions,especially under high heat-mass ratio,has not been systematically carried out.In this paper,the heat transfer and flow characteristics of related high temperature fuels are studied by using typical engine parallel channel structure.Through numeri⁃cal simulation and systematic experimental verification,the flow and heat transfer characteristics of parallel chan⁃nels under typical working conditions are obtained,and the effectiveness of high-precision calculation method is preliminarily established.It is known that the stable time required for hot start of regenerative cooling engine is about 50 s,and the flow resistance of parallel channel structure first increases and then decreases with the in⁃crease of equivalence ratio(The following equivalence ratio is expressed byΦ),and there is a flow resistance peak in the range ofΦ=0.5~0.8.This is mainly caused by the coupling effect of high temperature physical proper⁃ties,flow rate and pressure of fuel in parallel channels.At the same time,the cooling and heat transfer character⁃istics of parallel channels under some conditions of high heat-mass ratio are obtained,and the main factors affect⁃ing the heat transfer of parallel channels such as improving surface roughness and strengthening heat transfer are mastered.In the experiment,whenΦis less than 0.9,the phenomenon of local heat transfer enhancement and deterioration can be obviously observed,and the temperature rise of local structures exceeds 200℃,which is the risk of structural damage.Therefore,the reliability of long-term parallel channel structure under the condition of high heat-mass ratio should be fully considered in structural design.
基金College Students Innovation and Entrepreneurship Project of Guangzhou Railway Polytechnic(2025CXCY015)。
文摘As the dominant seepage channel in rock masses,it is of great significance to study the influence of fracture roughness distribution on seepage and heat transfer in rock masses.In this paper,the fracture roughness distribution functions of the Bakhtiary dam site and Oskarshamn/Forsmark mountain were fitted using statistical methods.The COMSOL Multiphysics finite element software was utilized to analyze the effects of fracture roughness distribution types and empirical formulas for fracture hydraulic aperture on the seepage field and temperature field of rock masses.The results show that:(1)The fracture roughness at the Bakhtiary dam site and Oskarshamn/Forsmark mountain follows lognormal and normal distributions,respectively;(2)For rock masses with the same expected value and standard deviation of fracture roughness,the outflow from rock masses with lognormal distribution of fracture roughness is significantly larger than that of rock masses with normal distribution of fracture roughness;(3)The fracture hydraulic aperture,outflow,and cold front distance of the Li and Jiang model are significantly larger than those of the Barton model;(4)The outflow,hydraulic pressure distribution,and temperature distribution of the Barton model are more sensitive to the fracture roughness distribution type than those of the Li and Jiang model.
文摘The use of nanofluids as heat transfer media represents an innovative strategy to enhance heat transfer performances.This study investigates experimentally the turbulent convective heat transfer characteristics of waterbased nanofluids containing TiO_(2),CuO,and graphene nanoplatelet(GNP)nanoparticles as they flow through a copper tube.Both the dynamic viscosity and thermal conductivity of these nanofluids were modeled and experimentally measured across varying nanoparticle concentrations(0.01,0.02,and 0.03 vol.%)and temperatures(25℃,35℃,and 45℃).The findings indicate that the behavior of nanofluids depends on the parameter used for comparison with the base fluid.Notably,both the friction factor and heat transfer coefficient increase with higher nanoparticle volume concentrations at a constant Reynolds number.The results further reveal that the GNP/water nanofluid,with a volume concentration of 0.03%at 45℃,exhibit the highest Nusselt number,followed by the CuO/water and TiO_(2)/water nanofluids,with respective increases of 17.8%,11.09%,and 8.11%.
基金supported by the Shandong Provincial Natural Science Foundation,China(Grant ZR2024ME136).
文摘The growing need for enhanced heat dissipation is compelling the development of more effective heat exchangers.Innovation inspired by nature bionics,four types of leaf-shaped pin fins were proposed and four combinations of them were considered.The leaf-shaped design of the cooling pin fin enhances uniformity and synergy,effectively creating an optimized flow path that boosts cooling performance.Eight three-dimensional conjugate heat transfer models in staggered arrangement were developed using ANSYS-Fluent software.Aluminum6061material was used as the heat sinkmaterial and single-phase liquid water flowed through the rectangular channel where the Reynolds(R_(e))number varies from 40 to 100.Using the same boundary conditions as the software simulations,two leaf-shaped channels were printed to validate numerical models.Velocity field and temperature differences of the eight proposed leaf-shaped pin fins configurations were discussed by comparison with cylindrical pin fins.Based on the findings of this study,at a Reynolds number of 80,the Leaf B Staggered Array(LBSA)records a maximum temperature that is 0.72 K lower than that of the cylindrical pin fins arrangement.Additionally,the LBSA exhibits a reduction in the friction factor by approximately 33.3%relative to the circular pin fins array under the same R_(e).This implies that the design of LBSA has been optimized to provide better heat dissipation performance while maintaining lower energy consumption.Furthermore,the LBSA demonstrates the most favorable thermal-hydraulic performance index(TPI),which is 1.18 times higher than that of the circular pin fins arrangement at R_(e)=80.The temperature reduction and friction factor reduction of the lobed channel is more pronounced than that of the conventional cooling channel,highlighting its potential to increase heat transfer efficiency and reduce energy consumption in practical applications.
基金financial support was provided by the National Natural Science Foundation of China(Nos.52476146,52006008,and 52471219)the Guangdong Basic and Applied Basic Research Foundation(2023A1515140059 and 2025A1515011255)+2 种基金the Peking University Third Hospital Haidian transformation project(HDCXZHKC2023210)the National Foreign Expert Individual Human Project(Category H,No.H20240116)the State Key Laboratory of New Ceramic Materials Tsinghua University(No.KFZD202402).
文摘The latent heat thermal energy storage system with solid-liquid phase-change material(SLPCM-LHTES)as energy storage medium provides outstanding advantages such as system simplicity,stable temperature control,and high energy storage density,showing great potential toward addressing the energy storage problems associated with decentralized,intermittent,and unstable renewable energy sources.Notably,effective heat transfer within the SLPCM-LHTES is crucial for extending its application potential.Therefore,a comprehensive understanding of the heat transfer processes in SLPCM-LHTES from a theoretical perspective is necessary.In this review,we propose a three-stage heat transfer pathway in SLPCM-LHTES,including external heating,interfacial heat transfer,and intrinsic phase transition processes.From the perspective of this three-stage pathway,the theoretical basis of heat transfer processes and typical efficiency enhancement strategies in SLPCM-LHTES are summarized.Moreover,an overview of the typical applications of SLPCM-LHTES in various fields,such as building energy efficiency,textiles and garments,and battery thermal management,is presented.Finally,the remaining challenges and possible avenues of research in this burgeoning field will also be discussed.
文摘Plate heat exchangers suffer from significant energy losses,which adversely affect the overall efficiency of thermal systems.To address this challenge,various heat transfer enhancement techniques have been investigated.Notably,the incorporation of surface corrugations is widely recognized as both effective and practical.Chevron corrugation is the most employed design.However,there remains a need to investigate alternative geometries that may offer superior performance.This study aims to find a novel corrugation design by conducting a comparative CFD analysis of flat,square,chevron,and cylindrical corrugated surfaces,assessing their impact on heat transfer enhancement within a plate heat exchanger.ANSYS Fluent software was used for simulation at four distinct Reynolds numbers(10,000,18,000,26,000,and 28,000),with a heat flux of 12,000 W/m^(2).A structured mesh was generated using Pointwise software.The material of the solid plates was modelled as aluminum,the fluid was modelled as water,and the flow was turbulent.To obtain a fully developed turbulent flow,a separate inlet duct was modelled,and the output velocity profile of the inlet duct was input into the plate heat exchanger.The Nusselt number(Nu)and heattransfer coefficient(h)were calculated to evaluate the performance of all surfaces.The results indicate that cylindrical corrugated surfaces exhibit higher Nusselt numbers than chevron,square,and flat plates.This higher performance is because of the generation of vortices in the middle of the cylindrical texture.Consequently,flow recirculation occurs,leading to reattachment to the mainstreamflow.This phenomenon induces increased turbulence,thereby enhancing the heat transfer efficiency.To validate the results,a grid-convergence independence test was performed for three different mesh sizes.In addition,empirical calculations were performed using the Dittus-Boelter and the Genilaski equations to validate the results of the flat-plate heat exchanger.It was concluded that the cylinder was the best corrugated surface and had a maximum heat transfer 35%higher than that of a flat plate.
基金support by Beijing Natural Science Foundation(3194046)BUCEA Post Graduate Innovation Project.
文摘The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation section paired with superhydrophilic,superhydrophobic,and hybrid condensation section).The Volume of Fluid(VOF)model was utilized to capture the phase-change process within the PHPs.The study also evaluated the influence of surface wettability on fluid patterns and thermo-dynamic heat transfer performance under various heat fluxes.The results indicated that the effective nucleation and detachment of droplets are critical factors influencing the thermal performance of the PHPs.The overall heat transfer performance of the superhydrophobic surface was significantly improved at low heat flux.Under medium to high heat flux,the superhydrophilic condensation section exhibits a strong oscillation effect and leads to the thickening of the liquid film.In addition,the hybrid surface possesses the heat transfer characteristics of both superhydrophilic and superhydrophobic walls.The hybrid condensation section exhibited the lowest thermal resistance by 0.45 K/W at the heat flux of 10731 W/m^(2).The thermal resistance is reduced by 13.1%and 5.4%,respectively,compared to the superhydrophobic and superhydrophilic conditions.The proposed surface-modification method for achieving highly efficient condensation heat transfer is helpful for the design and operation of device-cooling components.
文摘The pivotal role microchannels play in the thermal management of electronic components has,in recent decades,prompted extensive research into methods for enhancing their heat transfer performance.Among these methods,surface wettability modification was found to be highly effective owing to its significant influence on boiling dynamics and heat transfer mechanisms.In this study,we modified surface wettability using a nanocomposite coating composed of graphene nano plate(GNPs)and multi-walled carbon nanotubes(MWCNT)and then examined how the modification affected the transfer of boiling heat in microchannels.The resultant heat transfer coefficients for hydrophilic and hydrophilic composite(GNPs+MWCNT)microchannels were,respectively,42.8%and 33.95%higher compared with that of the uncoated surface.These results verify that hydrophilic GNP-based coating significantly improves boiling heat transfer performance.It was observed that a minor increase in contact angle,θfrom 73.142°to 75.73°,resulted in a noticeable decrease in thermal performance.This is attributed to diminished liquid film stability,reduced nucleation site activity,and weakened capillary-driven liquid replenishment.These findings underscore the crucial role of optimized surface wettability in maintaining efficient microchannel boiling.At high mass flux,the GNPS microchannels exhibited maximum pressure drop values,with a pressure drop ratio as high as 36%compared to 29%for the GNPs+MWCNT composite samples.Nevertheless,when a composite hydrophilic–hydrophobic coating was deposited through electrodeposition,the enhancement in heat transfer was less significant.This was probably due to decreased surface uniformity,diminished liquid film stability,and the disruption of effective nucleation behavior,all associated with the slight increase in surface contact angle.The obtained results can be used as guidance for designing advanced cooling surfaces in high-performance microelectronic and energy systems,where precise control of surface characteristics is critical.
基金supported by the Natural Science Basic Research Program of Shaanxi(Program No.2024JC-YBMS-449)Project ZR2022QE233 supported by Shandong Provincial Natural Science Foundation.
文摘In exploring hypersonic propulsion,precooler combined engines require the development of lightweight,efficient,and compact heat exchangers(HX).As additive manufacturing technology continues to progress,triply periodic minimal surface(TPMS)structures,characterized by exceptionally high surface area to volume ratios and intricate geometric structures,have demonstrated superior heat transfer performance.This research examines the thermal-hydraulic(TH)behavior of FKS and Diamond as heat transfer structures under different Reynolds numbers through numerical simulations.The Nusselt number for FKS is 13.2%–17.6%higher than Diamond,while the friction factor for FKS is approximately 18.8%–29.3%higher.A detailed analysis of the internal flow mechanisms reveals that the flow pattern within TPMS can be summarized as cyclic convergence-separation-convergence.The fluid experiences constant disturbances from the structure in all spatial directions,generating strong turbulent mixing and large wall shear stresses,which significantly enhance heat transfer performance.
基金funded by the Scientific and Technological Research Projects in Henan Province(No.252102310425)the Key Scientific Research Projects of Higher Education Institutions in Henan Province(No.23A560018).
文摘Freeze-drying of structurally heterogeneous biomaterials such as porcine aorta presents considerable modeling challenges due to their inherent multilayer composition and moving sublimation interfaces.Conventional models often overlook structural anisotropy and dynamic boundary progression,while experimental determination of key parameters under cryogenic conditions remains difficult.To address these,this study develops a heat and mass transfer model incorporating a dynamic node strategy for the sublimation interface,which effectively handles continuous computational domain deformation.Additionally,specialized fixed nodes were incorporated to adapt to the multilayer structure and its spatially varying thermophysical properties.A novel non-contact gravimetric system was introduced to monitor mass loss in real time without disrupting vacuum,enabling accurate experimental validation.Combined with dehydration data,the model quantified critical parameters including effective thermal conductivity of the dried layer,vapor diffusivity,and sublimation mass transfer resistance.The results show that the migration of the sublimation fronts from both the inner and outer tunics toward the tunica media significantly alters the drying kinetics and heat-mass transfer characteristics.The proposed approach provides an adaptable and predictive framework for simulating freeze-drying processes in structurally heterogeneous systems with spatially varying thermophysical properties.
基金supported by the Laoshan Laboratory(No.LSKJ202201600)the National Natural Science Foundation of China(No.41821004)。
文摘The heat transfer coefficient of the water surface is an important parameter in the design of thermal discharge in nuclear power plant engineering.In this study,in situ observations were performed in the northwestern South China Sea near a coastal nuclear power plant to evaluate the applicability of heat transfer coefficient calculation algorithms commonly used in marine thermal discharge engineering in China.The results show that the Regulation for Hydraulic and Thermal Model in Cooling Water Projects(SL 160-2012)is not applicable in calculating the heat transfer coefficient in offshore areas.SL 160-2012 significantly overestimates the heat loss at the sea surface.However,Code for Design of Cooling for Industrial Recirculating Water(GB/T 50102-2014)performs well,and its estimation coefficient is roughly consistent with the estimations of the COARE 3.6 bulk algorithm,which is extensively used in physical oceanography for calculating air-sea heat fluxes,and the Gunneberg formula.In a 3-day observation,the average heat transfer coefficients estimated using these three algorithms were 50.4,48.5,and 48.8 W m^(-2)℃^(-1),respectively,with a deviation of less than 4% among them,whereas that estimated using SL 160-2012 was as high as 176.3 W m^(-2)℃^(-1).The abnormally large value of SL 160-2012 is due to its additional cooling term,which is artificially increased by 100 times because of the incorrect unit conversion used when developing the regulation.If this error is corrected,the value will decrease to 50.5 W m^(-2)℃^(-1),which is very close to the estimation of GB/T 50102-2014.
