Two kinds of 2.5D deep straight-joint structure ultra-high molecular weight polyethylene（UHMWPE）（twisted and original） fibers woven fabric reinforced epoxy resin composites were prepared by the hand lay-up method....Two kinds of 2.5D deep straight-joint structure ultra-high molecular weight polyethylene（UHMWPE）（twisted and original） fibers woven fabric reinforced epoxy resin composites were prepared by the hand lay-up method. Subsequently, the flexural property, microstructures, and failure mechanisms of the composites were also investigated. The average flexural strength of 2.5D deep bend-joint structure twisted fiber and original fiber woven fabric composites were 176.66 MPa and 204.45 MPa, respectively. The results of the characteristics indicated that the twist was the main factor which affected the flexural performance. Flexural property vitally relied on the strength of the fiber itself. Twist decreased the strength of the yarns, which meant that when the mechanical property of woven fabric reinforced composites was improved, the yarns must be kept straight in the woven fabric. The study are extremely valuable to guide the improvement of the mechanical property of the woven fabric reinforced composites.展开更多
This study investigates the low-velocity impact and post-impact flexural properties of 3D integrated woven spacer composites,focusing on their orthotropic behavior when tested along two principal directions,i.e.,warp(...This study investigates the low-velocity impact and post-impact flexural properties of 3D integrated woven spacer composites,focusing on their orthotropic behavior when tested along two principal directions,i.e.,warp(X-type)and weft(Y-type)directions.The same composite material was tested in these orientations to evaluate the differences in impact resistance and residual bending strength.Specimens were fabricated via vacuum-assisted molding and tested at 2,3,5,and 7 J impact energies using an Instron Ceast 9350 drop-weight impact testing machine,in accordance with ASTM D7136.Post-impact flexural tests were performed using a four-point bending method in accordance with ASTM D7264.The absorbed energy increased from 1.97 to 6.98 J,and the panel damage area ranged from 121 to 361 mm^(2) as impact energy roses.Specimens tested in the weft direction(Y-type)showed greater residual strength(up to 15.83 N)and displacement(up to 0.538 mm)than those tested in the warp direction(X-type).Ultrasonic C-scan imaging revealed localized matrix cracking and fiber failure damage patterns.Results emphasize the directional differences in impact resistance and residual bending properties,highlighting the importance of material orientation in structural applications.This study provides a foundation for utilizing 3D woven spacer composites in lightweight,damage-tolerant structural components.展开更多
To improve the applications of beetle elytron plates(BEPs,which are biomimetic sandwich plates inspired by beetle elytra),the flexural performance and its synergistic mechanism of multibody molded BEPs were investigat...To improve the applications of beetle elytron plates(BEPs,which are biomimetic sandwich plates inspired by beetle elytra),the flexural performance and its synergistic mechanism of multibody molded BEPs were investigated via cantilever testing and finite element method(FEM).The results are summarized as follows.(1)Although debonding damage causes failure of the multibody molded BEPs and honeycomb plate and the reasonable range of trabecular size for BEPs is narrow,both the optimal loading capacity per mass and failure deformation of the BEPs are over two times those of the honeycomb plate.(2)A flexural synergistic mechanism is revealed in the trabecular-honeycomb core structure of BEPs;this mechanism causes the maximum deformation of core structure to gradually transfer from the honeycomb wall to the trabeculae with the increase inη(the ratio of the trabecular radius to the distance between the center points of two trabeculae),which means the different stretching behaviors in these core structures.(3)Unlike the compressive mechanism of BEPs,by controlling and balancing the deformation degrees of the trabeculae and honeycomb walls,the flexural mechanism achieves a minimum core deformation and an optimal flexural performance.These results suggest a qualitative relationship between the deformation behavior of trabecular-honeycomb core structure and bending performance of the whole BEP,and provide a solid foundation for subsequent research and the considerable application potential of this biomimetic sandwich structure in many fields.展开更多
Four kinds of iron oxide pigments were added into wood-fiber/high-density-polyethylene composites （WF/HDPE） at three different concentrations, to determine the effects of pigments on the changes in the color and mec...Four kinds of iron oxide pigments were added into wood-fiber/high-density-polyethylene composites （WF/HDPE） at three different concentrations, to determine the effects of pigments on the changes in the color and mechanical properties of the composites before and after UV accelerated weathering. HDPE, wood fibers, pigments and other processing additives were dry-mixed in a high-speed mixer. The mixtures were extruded by two-step extrusion process with a self-designed twin-screw/single-screw extruder system. Color of the samples was determined according to CIE 1976 L^＊a^＊b^＊ system by a spec- trophotometer and the bending properties were tested to evaluate the mechanical properties before and after accelerated UV weathering. The result shows that the modulus of elasticity of WF/HDPE did not obvi- ously changed after incorporating with the pigments, but the bending strength increased. After accelerated aging for 2000 h, both color and mechanical properties significantly changed. Iron oxide red and black performed better than the other two pigments, and the pigments dosage of 2.28% in the composites is favourable.展开更多
In this paper, acrylonitrile-butadiene-styrene （ABS） nanocomposite foams are produced using carbon dioxide through the solid-state batch process. Microcellular closed-cell foams are produced with the relative densit...In this paper, acrylonitrile-butadiene-styrene （ABS） nanocomposite foams are produced using carbon dioxide through the solid-state batch process. Microcellular closed-cell foams are produced with the relative density ranging from 0.38 to 0.97. The effects of the processing conditions on the density, morphology, and flexural properties of ABS and its nanocomposite foams are studied. It is found that nanoclay particles, as nucleating sites, play an important role in reducing the size of cells and increasing their number in the unit volume of foamed polymer, as well as increasing the flexural modulus of foam through reinforcing its matrix.展开更多
Flax and hemp fibers were used as reinforcing materials to commingle with polypropylene(PP)fiber to realize the mixture of two materials at the stage of yarn.Meanwhile,PP filaments were introduced to produce a core-sp...Flax and hemp fibers were used as reinforcing materials to commingle with polypropylene(PP)fiber to realize the mixture of two materials at the stage of yarn.Meanwhile,PP filaments were introduced to produce a core-spun yarn with flax/PP as core and PP filament as outer sheath.The commingled yarns were woven into 2D fabric which was used as the prefabricated material.The composite laminates were prepared by hot press technology.The effects of manufacture technology,yarn structure,and fiber weight fraction on flexural properties of composites were investigated.展开更多
An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increas...An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increase the ductility and crack resisting ability of the beam. Based on the assumption of the plane remaining plane and the simplified constitutive models of materials, the stress and strain distributions along the depth of the composite beam in different loading stages are comprehensively investigated to obtain calculation methods of the load-carrying capacities for different stages. Also, a simplified formula for the ultimate load carrying capacity is proposed according to the Chinese code for the design of concrete structures. The relationship between the moment and curvature for the composite beam is also proposed together with a simplified calculation method for ductility of the ECC/RC composite beam. Finally, the calculation method is demonstrated with the test results of a composite beam. Comparison results show that the calculation results have good consistency with the test results, proving that the proposed calculation methods are reliable with a certain theoretical significance and reference value.展开更多
Damping improvement in composite structures via introducing nanofillers generally has remarkable negative effects on the other mechanical properties. Therefore, in the present work, SiC and A1203 nanoparticles＇ infus...Damping improvement in composite structures via introducing nanofillers generally has remarkable negative effects on the other mechanical properties. Therefore, in the present work, SiC and A1203 nanoparticles＇ infusion effects on the flexural, interracial and vibration properties of epoxy matrix and glass fiber reinforced epoxy （GFR/E） laminates were investigated. Unidirectional （UD-GFR/E） and quasi-isotropic （QI-GFR/E） laminates with [0/± 45/90]s and [90/±45/0]s stack- ing sequences were hybridized by the optimum nanoparticles percentages. Results from off-axis flexural strengths of UD-GFR/E demonstrate good fiber/nanophased-matrix interracial bonding. The interlaminar shear stress between the adjacent layers with different orientations/strains of duc- tile QI-GFR/SiC/E laminates results in decreasing the flexural strengths respectively by 24.3% and 9.1% for [0/±45/90]s and [90/± 45/0]s stacking sequences and increasing the dissipated interfacial friction energy and thus the damping by 105.7% and 26.1%. The damping of QI-GFR/E, QI-GFR/SiC/E and QI-GFR/AI203/E laminates with [90/± 45/0]s stacking sequence was increased by 111.4%, 29.7% and 32.9% respectively compared to [0/± 45/90]s stacking sequence.展开更多
According to the theory of phononic crystals, the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps. We presen...According to the theory of phononic crystals, the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps. We present theoretical and experimental investigations into the flexural vibration transfer properties of a high-pressure periodic pipe with the force on the inner pipe wall by oii pressure taken into consideration. The results show that the vibration attenuation of periodic pipe decreases along with the elevation of working pressure for the hydraulic system, and the band gaps in low frequency ranges move towards high frequency ranges. The periodic pipe has good vibration attenuation performance in the frequency range below 1000 Hz and the vibration of the hydraulic system is effectively suppressed. A11 the results are validated by experiment. The experimental results show a good agreement with the numerical calculations, thus the flexural vibration transfer properties of the high- pressure periodic pipe can be precisely calculated by taking the fluid structure interaction between the pipe and oil into consideration. This study provides an effective way for the vibration control of the hydraulic system.展开更多
Properties and mechanism were investigated on flexural fatigue of concrete containing polypropylene fibers and ground granulated blast furnace slag（GGBFS）.Four polypropylene fibers’volume fractions and five slag pr...Properties and mechanism were investigated on flexural fatigue of concrete containing polypropylene fibers and ground granulated blast furnace slag（GGBFS）.Four polypropylene fibers’volume fractions and five slag proportions were considered.An experiment was conducted to obtain the fatigue lives at three stress levels in 20 Hz frequency and at a constant stress level of 0.59 in four frequency respectively.Mechanism and evaluation were investigated based on the experimental data.Fatigue life span models were established.The results show that the addition of polypropylene fibers improves the flexural fatigue cumulative strength and fatigue life span.It is proposed that the slag particles and hydrated products improve Interfacial Transition Zone（ITZ）structure and benefit flexural fatigue performance.A composite reinforce effect is found with the incorporation of slag and polypropylene fibers.The optimum mixture contents 55%slag with 0.6%polypropylene fiber for the cumulative fatigue stress.Fatigue properties are decreased as the stress level increasing,the higher frequency reduces the fatigue strength more than lower frequency at a constant stress level.展开更多
The flexural strength reliability of bulk metallic glasses （BMGs） plates is analyzed using Weibull statistics. The Weibull modulus （m） and characteristic strength （σ0） of the Zr48Cu45AI7 BMG are 34 and 2630 MPa...The flexural strength reliability of bulk metallic glasses （BMGs） plates is analyzed using Weibull statistics. The Weibull modulus （m） and characteristic strength （σ0） of the Zr48Cu45AI7 BMG are 34 and 2630 MPa, respectively, which are much higher than the values of fine ceramics （m 〈 30, σ0 〈 1600 MPa）. In particular, the m values obtained by flexural strength and compressive strength statistics of the Mg61Cu28Gd11 BMG are 5 and 33, respectively, indicating that the m values of BMGs are test method dependent, and only the m values obtained by flexural strength statistics can be used to make a convincible comparison with those of ceramics.展开更多
To improve the flexural properties of Beetle Elytron Plates(BEPs)and clarify the effect of the transition arcs(chamfers)between the skins and the trabeculae,the chamfers were set in BEPs,and then the influence of the ...To improve the flexural properties of Beetle Elytron Plates(BEPs)and clarify the effect of the transition arcs(chamfers)between the skins and the trabeculae,the chamfers were set in BEPs,and then the influence of the chamfer on BEPs'mechanical properties was investigated via experimentation and the Finite Elemnent Method simulation(FEM).The results indicate that the influence of the chamfer on the flexural properties and ductility was most obvious in the Trabecular Beetle Elytron Plates(TBEPs),less obvious in the Honeycomb Plates(HPs)and basically no efiect was observed on End-trabecular Beetle Elytron Plates(EBEPs).The chamfer can improve the mechanical stability of EBEPSs.As the chamfer diameter increased in the BEPs,the length of the residual trabecular root on the skin increased when failure occurred in the TBEPs.The crack position in the honeycomb wallsof the HPs gradually shifted from the skin to the center.The EBEPs continued to exhibit oblique cracks.From the perspective of the force characteristics of these BEPs.combined with numerical simulation,the influence mechanism of the chamfer on their flcxural propertics was investigated.展开更多
A three-dimensional finite element analysis was conducted to evaluate the feasibility of predicting the flexural properties of hydroxyapatite-reinforced poly-L-lactide acid （HA/PLLA） biocomposite using three differe...A three-dimensional finite element analysis was conducted to evaluate the feasibility of predicting the flexural properties of hydroxyapatite-reinforced poly-L-lactide acid （HA/PLLA） biocomposite using three different schemes. The scheme 1, originated from a beam analysis, was used to determine the flexural modulus analytically while the scheme 2 and 3 were designed to have different loading and boundary conditions using a finite element cell modeling approach. An empirical approach using Chow＇s formula and experimental data were used for comparison with the predicted results. In order to reduce the computational time and save the storage space involved in determining the effect of varying particle volume fractions on the flexural properties of HA/PLLA, a superelement technique was applied. The results using the scheme 3 and the Chow＇s formula were found to be in reasonable agreement with experimental results over the range of particle volume fraction. In addition to the Chow＇s formula, local stress distribution and the failure processes in HA/PLLA were simulated using the finite element technique.展开更多
Selecting H-60 PVC foam, four-axis E-glass non-woven fabric and vinyl resin, a type of innovative reinforced sandwich composite as grooved perforation sandwich （GPS） were fabricated by VIMP. The interfacial structur...Selecting H-60 PVC foam, four-axis E-glass non-woven fabric and vinyl resin, a type of innovative reinforced sandwich composite as grooved perforation sandwich （GPS） were fabricated by VIMP. The interfacial structure between the face and core of the sandwich is innovative because of the acuminate grooves in both sides of foam core and the holes perforated along core’s height. The fabrication results show that VIMP is a high-speed and cost-effective manufacturing method. The mechanical properties of the reinforced foam core were tested. The typical flexural failure modes of sandwich specimens were observed. The flexural stiffness and ultimate bearing capacity of sandwich were studied by ordinary sandwich beam theory and finite element method.展开更多
The aim of this research was to develop an intrarradicular dental post based on epoxy resin/nano zirconium phosphate composite with potential appli-cation in prosthetic dentistry. Zirconium phosphate (ZrP) nanoparticl...The aim of this research was to develop an intrarradicular dental post based on epoxy resin/nano zirconium phosphate composite with potential appli-cation in prosthetic dentistry. Zirconium phosphate (ZrP) nanoparticle was synthesized by a reaction between phosphoric acid (H3PO4) and zirconium (IV) oxide chloride 8-hydrate (ZrOCl2·8H2O) and applied as filler. Commer-cial epoxy resin and hardener were used as polymer matrix. The composites were prepared at different proportions of epoxy resin/hardener, filler amount, reaction time and temperature. Infrared revealed that degree of conversion decreased with amount of ZrP. Insoluble matter was upper than 97%. Thermogravimetry indicated two steps of degradation. The best values of flexural modulus and flexural strength were achieved for the post desig-nated as 1:0.25:0.25. Laser scanning confocal microscopy suggested that the morphology of the posts fractured surface varied according to epoxy-resin:hardener ratio and the ZrP amount. From atomic force micros-copy, the topographic view exposed the shape and size of ZrP particles. Field emission scanning electron microscopy and energy dispersive spectroscopy indicated good adhesion between epoxy resin matrix-ZrP and that the pres-ence of phosphate rendered brittle the fracture surface.展开更多
A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-rein...A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-reinforced Ti matrix composite. In the Ti-Al intermetallic multilayered composite part, a series of Ti-Al intermetallics compounds, including Ti3Al, TiAl, TiAl2 and TiAl3, were formed between the Ti layers. In the continuous SiC fibers-reinforced Ti matrix composite part, SiC fibers and Ti matrix were found to be bonded well through weak interface reaction. Flexural strength of this material reached 1.21 ±0.16 GPa, measured by three-point bending test. The deformation features suggest that the hierarchical structure combining ductile Ti layers/matrix with brittle high-strength Ti-Al intermetallics layers/SiC fibers can effectively enhance the mechanical properties of the bio-inspired hybrid composite.展开更多
SiC nanowires reinforced C/(PyC-SiC)_(n)multilayered matrix composites(SM-CS for short)were prepared by combined with sol-gel and chemical vapor infiltration(CVI)method.Firstly,(PyC-Si OC);multilayered structure was f...SiC nanowires reinforced C/(PyC-SiC)_(n)multilayered matrix composites(SM-CS for short)were prepared by combined with sol-gel and chemical vapor infiltration(CVI)method.Firstly,(PyC-Si OC);multilayered structure was formed by cycles of impregnation and deposition.Then SiOC was transformed into SiC by heat-treatment,and(PyC-SiC)_(n)multilayered structure would be obtained.At the same time,the PyC layer which was designed as the outmost layer could decrease gas supersaturation to form in-situ tubular SiC nanowires on the surface of multilayered structure.The results of three-point bending test showed that the maximum force of SM-CS composites was increased by the number of cycles of the preparation process,which were up to enhanced by 74.38%compared with C/C composite materials.The fracture surface showed that the improvement was due to the multiscale reinforcing system of(PyC-SiC)_(n)multilayered structure and SiC nanowires.Multilayered structure can protect carbon fibers and release stress concentration by induction of cracks.And the mechanical interlocking effect of SiC nanowires could reinforce bonding force of the remaining matrix.展开更多
The static test of 13 square hollow section(SHS) X-joints with different β and different types of plate reinforcement under in-plane moment in brace was carried out. Experimental test schemes, failure modes of specim...The static test of 13 square hollow section(SHS) X-joints with different β and different types of plate reinforcement under in-plane moment in brace was carried out. Experimental test schemes, failure modes of specimens, moment-vertical displacement curves, moment-deformation of the chord, and strain strength distribution curves were presented. The effect of β and plate reinforcement types on in-plane flexural property of SHS X-joints was studied. Results show that punching shear of chord face disappears, brace material fracture appears and concave and convex deformation of chord decrease when either collar plates or doubler plates were welded on chord face. Moment-vertical displacement curves of all specimens have obvious elastic, elastic-plastic and plastic stages. As β increases, the in-plane flexural ultimate capacity and initial stiffness of joints of the same plate reinforcement type increase, but ductility of joints decreases. With the same β, the in-plane flexural initial stiffness and ultimate capacity of doubler plate reinforced joints, collar plate reinforced joints, and unreinforced joints decrease progressively. Thickness of reinforcement plate has no obvious effect on in-plane flexural initial stiffness and ultimate capacity of joints. As thickness of reinforcement plate increases, the ductility of reinforced X-joints decreases. The concave and convex deformation of every specimen has good symmetry;as β increases, the yield and ultimate deformation of chord decrease.展开更多
Ultra-high molecular weight polyethylene（UHMWPE） fiber/epoxy composites were fabricated by a vacuum assisted resin infused（VARI） processing technology. The curing condition of composites was at a cure temperature ...Ultra-high molecular weight polyethylene（UHMWPE） fiber/epoxy composites were fabricated by a vacuum assisted resin infused（VARI） processing technology. The curing condition of composites was at a cure temperature of 80 ℃ for 3h in a drying oven. The characteristics of 2.5D（shallow bend-joint and deep straight-joint） structure and 3D orthogonal structure were compared. The failure behavior, flexural strength, and microstructures of both composites were investigated. It was found that the flexural property was closely related to undulation angle θ. The flexural strength of 3D orthogonal structure composite was superior to the other two structures composites with the same weave parameters and resin.展开更多
This study reports the investigations for repair of thermoplastic based automotive bumpers and bars with modified friction stir welding(MFSW)process.For MFSW,consumable tool of polyamide6(PA6)composite has been used f...This study reports the investigations for repair of thermoplastic based automotive bumpers and bars with modified friction stir welding(MFSW)process.For MFSW,consumable tool of polyamide6(PA6)composite has been used for joining of acrylonitrile butadiene styrene(ABS)composites.The dissimilar thermoplastics were processed for maintaining a useful range of melt flow properties followed by preparation of feed stock filament for fused deposition modeling(FDM)process through screw extrusion.Finally,3D printed PA6 based consumable rapid tool(RT)was prepared for MFSW.The joints prepared were subjected to flexural,hardness,morphological and thermal testing.The study has suggested the that maximum mechanical strength was obtained for sample welded at 1400 r/min,50 mm/min transverse speed and 3 mm plunge depth,whereas the minimum mechanical strength was obtained for sample welded at 1000 r/min,30 mm/min transverse speed and 2 mm plunge depth.The results are also supported with thermal analysis and photomicrographs.展开更多
基金Funded by the National Natural Science Foundation of China(No.51001117)
文摘Two kinds of 2.5D deep straight-joint structure ultra-high molecular weight polyethylene（UHMWPE）（twisted and original） fibers woven fabric reinforced epoxy resin composites were prepared by the hand lay-up method. Subsequently, the flexural property, microstructures, and failure mechanisms of the composites were also investigated. The average flexural strength of 2.5D deep bend-joint structure twisted fiber and original fiber woven fabric composites were 176.66 MPa and 204.45 MPa, respectively. The results of the characteristics indicated that the twist was the main factor which affected the flexural performance. Flexural property vitally relied on the strength of the fiber itself. Twist decreased the strength of the yarns, which meant that when the mechanical property of woven fabric reinforced composites was improved, the yarns must be kept straight in the woven fabric. The study are extremely valuable to guide the improvement of the mechanical property of the woven fabric reinforced composites.
基金funded by Open Foundation of the State Key Laboratory of Advanced Inorganic Fibers and Composites(Grant No.KF2024SYS02)the Jiangsu Province Special Fund for Carbon Peaking and Carbon Neutrality Technology Innovation(Grant No.BE2022008)the Prioritized Academic Program Development for Higher Education Institutions in Jiangsu.
文摘This study investigates the low-velocity impact and post-impact flexural properties of 3D integrated woven spacer composites,focusing on their orthotropic behavior when tested along two principal directions,i.e.,warp(X-type)and weft(Y-type)directions.The same composite material was tested in these orientations to evaluate the differences in impact resistance and residual bending strength.Specimens were fabricated via vacuum-assisted molding and tested at 2,3,5,and 7 J impact energies using an Instron Ceast 9350 drop-weight impact testing machine,in accordance with ASTM D7136.Post-impact flexural tests were performed using a four-point bending method in accordance with ASTM D7264.The absorbed energy increased from 1.97 to 6.98 J,and the panel damage area ranged from 121 to 361 mm^(2) as impact energy roses.Specimens tested in the weft direction(Y-type)showed greater residual strength(up to 15.83 N)and displacement(up to 0.538 mm)than those tested in the warp direction(X-type).Ultrasonic C-scan imaging revealed localized matrix cracking and fiber failure damage patterns.Results emphasize the directional differences in impact resistance and residual bending properties,highlighting the importance of material orientation in structural applications.This study provides a foundation for utilizing 3D woven spacer composites in lightweight,damage-tolerant structural components.
基金supported by the National Natural Science Foundation of China(Grant Nos.51875102,51578136).
文摘To improve the applications of beetle elytron plates(BEPs,which are biomimetic sandwich plates inspired by beetle elytra),the flexural performance and its synergistic mechanism of multibody molded BEPs were investigated via cantilever testing and finite element method(FEM).The results are summarized as follows.(1)Although debonding damage causes failure of the multibody molded BEPs and honeycomb plate and the reasonable range of trabecular size for BEPs is narrow,both the optimal loading capacity per mass and failure deformation of the BEPs are over two times those of the honeycomb plate.(2)A flexural synergistic mechanism is revealed in the trabecular-honeycomb core structure of BEPs;this mechanism causes the maximum deformation of core structure to gradually transfer from the honeycomb wall to the trabeculae with the increase inη(the ratio of the trabecular radius to the distance between the center points of two trabeculae),which means the different stretching behaviors in these core structures.(3)Unlike the compressive mechanism of BEPs,by controlling and balancing the deformation degrees of the trabeculae and honeycomb walls,the flexural mechanism achieves a minimum core deformation and an optimal flexural performance.These results suggest a qualitative relationship between the deformation behavior of trabecular-honeycomb core structure and bending performance of the whole BEP,and provide a solid foundation for subsequent research and the considerable application potential of this biomimetic sandwich structure in many fields.
基金supported by the National Natural Science Foundation of China (30671644, 30771680)
文摘Four kinds of iron oxide pigments were added into wood-fiber/high-density-polyethylene composites （WF/HDPE） at three different concentrations, to determine the effects of pigments on the changes in the color and mechanical properties of the composites before and after UV accelerated weathering. HDPE, wood fibers, pigments and other processing additives were dry-mixed in a high-speed mixer. The mixtures were extruded by two-step extrusion process with a self-designed twin-screw/single-screw extruder system. Color of the samples was determined according to CIE 1976 L^＊a^＊b^＊ system by a spec- trophotometer and the bending properties were tested to evaluate the mechanical properties before and after accelerated UV weathering. The result shows that the modulus of elasticity of WF/HDPE did not obvi- ously changed after incorporating with the pigments, but the bending strength increased. After accelerated aging for 2000 h, both color and mechanical properties significantly changed. Iron oxide red and black performed better than the other two pigments, and the pigments dosage of 2.28% in the composites is favourable.
文摘In this paper, acrylonitrile-butadiene-styrene （ABS） nanocomposite foams are produced using carbon dioxide through the solid-state batch process. Microcellular closed-cell foams are produced with the relative density ranging from 0.38 to 0.97. The effects of the processing conditions on the density, morphology, and flexural properties of ABS and its nanocomposite foams are studied. It is found that nanoclay particles, as nucleating sites, play an important role in reducing the size of cells and increasing their number in the unit volume of foamed polymer, as well as increasing the flexural modulus of foam through reinforcing its matrix.
文摘Flax and hemp fibers were used as reinforcing materials to commingle with polypropylene(PP)fiber to realize the mixture of two materials at the stage of yarn.Meanwhile,PP filaments were introduced to produce a core-spun yarn with flax/PP as core and PP filament as outer sheath.The commingled yarns were woven into 2D fabric which was used as the prefabricated material.The composite laminates were prepared by hot press technology.The effects of manufacture technology,yarn structure,and fiber weight fraction on flexural properties of composites were investigated.
基金The National Natural Science Foundation of China(No. 50808043)the National Basic Research Program of China (973 Program) (No. 2009CB623200)Foundation of Jiangsu Key Laboratory of Construction Materials,Program for Special Talents in Six Fields of Jiangsu Province(No. 2011-JZ-010)
文摘An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increase the ductility and crack resisting ability of the beam. Based on the assumption of the plane remaining plane and the simplified constitutive models of materials, the stress and strain distributions along the depth of the composite beam in different loading stages are comprehensively investigated to obtain calculation methods of the load-carrying capacities for different stages. Also, a simplified formula for the ultimate load carrying capacity is proposed according to the Chinese code for the design of concrete structures. The relationship between the moment and curvature for the composite beam is also proposed together with a simplified calculation method for ductility of the ECC/RC composite beam. Finally, the calculation method is demonstrated with the test results of a composite beam. Comparison results show that the calculation results have good consistency with the test results, proving that the proposed calculation methods are reliable with a certain theoretical significance and reference value.
文摘Damping improvement in composite structures via introducing nanofillers generally has remarkable negative effects on the other mechanical properties. Therefore, in the present work, SiC and A1203 nanoparticles＇ infusion effects on the flexural, interracial and vibration properties of epoxy matrix and glass fiber reinforced epoxy （GFR/E） laminates were investigated. Unidirectional （UD-GFR/E） and quasi-isotropic （QI-GFR/E） laminates with [0/± 45/90]s and [90/±45/0]s stack- ing sequences were hybridized by the optimum nanoparticles percentages. Results from off-axis flexural strengths of UD-GFR/E demonstrate good fiber/nanophased-matrix interracial bonding. The interlaminar shear stress between the adjacent layers with different orientations/strains of duc- tile QI-GFR/SiC/E laminates results in decreasing the flexural strengths respectively by 24.3% and 9.1% for [0/±45/90]s and [90/± 45/0]s stacking sequences and increasing the dissipated interfacial friction energy and thus the damping by 105.7% and 26.1%. The damping of QI-GFR/E, QI-GFR/SiC/E and QI-GFR/AI203/E laminates with [90/± 45/0]s stacking sequence was increased by 111.4%, 29.7% and 32.9% respectively compared to [0/± 45/90]s stacking sequence.
文摘According to the theory of phononic crystals, the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps. We present theoretical and experimental investigations into the flexural vibration transfer properties of a high-pressure periodic pipe with the force on the inner pipe wall by oii pressure taken into consideration. The results show that the vibration attenuation of periodic pipe decreases along with the elevation of working pressure for the hydraulic system, and the band gaps in low frequency ranges move towards high frequency ranges. The periodic pipe has good vibration attenuation performance in the frequency range below 1000 Hz and the vibration of the hydraulic system is effectively suppressed. A11 the results are validated by experiment. The experimental results show a good agreement with the numerical calculations, thus the flexural vibration transfer properties of the high- pressure periodic pipe can be precisely calculated by taking the fluid structure interaction between the pipe and oil into consideration. This study provides an effective way for the vibration control of the hydraulic system.
基金Funded by the National Science and Technology Support Plan (No.2006BAD11B03)Shaanxi Provincial Natural Science Foundation(No.SJ08E111)
文摘Properties and mechanism were investigated on flexural fatigue of concrete containing polypropylene fibers and ground granulated blast furnace slag（GGBFS）.Four polypropylene fibers’volume fractions and five slag proportions were considered.An experiment was conducted to obtain the fatigue lives at three stress levels in 20 Hz frequency and at a constant stress level of 0.59 in four frequency respectively.Mechanism and evaluation were investigated based on the experimental data.Fatigue life span models were established.The results show that the addition of polypropylene fibers improves the flexural fatigue cumulative strength and fatigue life span.It is proposed that the slag particles and hydrated products improve Interfacial Transition Zone（ITZ）structure and benefit flexural fatigue performance.A composite reinforce effect is found with the incorporation of slag and polypropylene fibers.The optimum mixture contents 55%slag with 0.6%polypropylene fiber for the cumulative fatigue stress.Fatigue properties are decreased as the stress level increasing,the higher frequency reduces the fatigue strength more than lower frequency at a constant stress level.
基金supported by the Zhejiang Provincial Natural Science Foundation of China(Grant No.Q12E010015)the Ningbo Municipal Natural Science Foundation(Grant No.2015A610074)
文摘The flexural strength reliability of bulk metallic glasses （BMGs） plates is analyzed using Weibull statistics. The Weibull modulus （m） and characteristic strength （σ0） of the Zr48Cu45AI7 BMG are 34 and 2630 MPa, respectively, which are much higher than the values of fine ceramics （m 〈 30, σ0 〈 1600 MPa）. In particular, the m values obtained by flexural strength and compressive strength statistics of the Mg61Cu28Gd11 BMG are 5 and 33, respectively, indicating that the m values of BMGs are test method dependent, and only the m values obtained by flexural strength statistics can be used to make a convincible comparison with those of ceramics.
基金funded by the National Key R&D Program of China(Grant No.2017YFC0703700).
文摘To improve the flexural properties of Beetle Elytron Plates(BEPs)and clarify the effect of the transition arcs(chamfers)between the skins and the trabeculae,the chamfers were set in BEPs,and then the influence of the chamfer on BEPs'mechanical properties was investigated via experimentation and the Finite Elemnent Method simulation(FEM).The results indicate that the influence of the chamfer on the flexural properties and ductility was most obvious in the Trabecular Beetle Elytron Plates(TBEPs),less obvious in the Honeycomb Plates(HPs)and basically no efiect was observed on End-trabecular Beetle Elytron Plates(EBEPs).The chamfer can improve the mechanical stability of EBEPSs.As the chamfer diameter increased in the BEPs,the length of the residual trabecular root on the skin increased when failure occurred in the TBEPs.The crack position in the honeycomb wallsof the HPs gradually shifted from the skin to the center.The EBEPs continued to exhibit oblique cracks.From the perspective of the force characteristics of these BEPs.combined with numerical simulation,the influence mechanism of the chamfer on their flcxural propertics was investigated.
基金Project supported by the Research Committee of the Hong Kong Polytechnic University (No.G-YX34).
文摘A three-dimensional finite element analysis was conducted to evaluate the feasibility of predicting the flexural properties of hydroxyapatite-reinforced poly-L-lactide acid （HA/PLLA） biocomposite using three different schemes. The scheme 1, originated from a beam analysis, was used to determine the flexural modulus analytically while the scheme 2 and 3 were designed to have different loading and boundary conditions using a finite element cell modeling approach. An empirical approach using Chow＇s formula and experimental data were used for comparison with the predicted results. In order to reduce the computational time and save the storage space involved in determining the effect of varying particle volume fractions on the flexural properties of HA/PLLA, a superelement technique was applied. The results using the scheme 3 and the Chow＇s formula were found to be in reasonable agreement with experimental results over the range of particle volume fraction. In addition to the Chow＇s formula, local stress distribution and the failure processes in HA/PLLA were simulated using the finite element technique.
基金Funded by the Special Prophase Project on Basic Research of The Na-tional Department of Scientific and Technology(No. 2008CB617613)the National Natural Science Foundation of China (No. 50978134)the Research Award Fund for Young Teachers of Nanjing University of Technology
文摘Selecting H-60 PVC foam, four-axis E-glass non-woven fabric and vinyl resin, a type of innovative reinforced sandwich composite as grooved perforation sandwich （GPS） were fabricated by VIMP. The interfacial structure between the face and core of the sandwich is innovative because of the acuminate grooves in both sides of foam core and the holes perforated along core’s height. The fabrication results show that VIMP is a high-speed and cost-effective manufacturing method. The mechanical properties of the reinforced foam core were tested. The typical flexural failure modes of sandwich specimens were observed. The flexural stiffness and ultimate bearing capacity of sandwich were studied by ordinary sandwich beam theory and finite element method.
文摘The aim of this research was to develop an intrarradicular dental post based on epoxy resin/nano zirconium phosphate composite with potential appli-cation in prosthetic dentistry. Zirconium phosphate (ZrP) nanoparticle was synthesized by a reaction between phosphoric acid (H3PO4) and zirconium (IV) oxide chloride 8-hydrate (ZrOCl2·8H2O) and applied as filler. Commer-cial epoxy resin and hardener were used as polymer matrix. The composites were prepared at different proportions of epoxy resin/hardener, filler amount, reaction time and temperature. Infrared revealed that degree of conversion decreased with amount of ZrP. Insoluble matter was upper than 97%. Thermogravimetry indicated two steps of degradation. The best values of flexural modulus and flexural strength were achieved for the post desig-nated as 1:0.25:0.25. Laser scanning confocal microscopy suggested that the morphology of the posts fractured surface varied according to epoxy-resin:hardener ratio and the ZrP amount. From atomic force micros-copy, the topographic view exposed the shape and size of ZrP particles. Field emission scanning electron microscopy and energy dispersive spectroscopy indicated good adhesion between epoxy resin matrix-ZrP and that the pres-ence of phosphate rendered brittle the fracture surface.
基金financially supported by the Defense Industrial Technology Development Program(JCKY2017205B032)National Natural Science Foundation of China(Nos.51405458,51371066 and 51331005)
文摘A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-reinforced Ti matrix composite. In the Ti-Al intermetallic multilayered composite part, a series of Ti-Al intermetallics compounds, including Ti3Al, TiAl, TiAl2 and TiAl3, were formed between the Ti layers. In the continuous SiC fibers-reinforced Ti matrix composite part, SiC fibers and Ti matrix were found to be bonded well through weak interface reaction. Flexural strength of this material reached 1.21 ±0.16 GPa, measured by three-point bending test. The deformation features suggest that the hierarchical structure combining ductile Ti layers/matrix with brittle high-strength Ti-Al intermetallics layers/SiC fibers can effectively enhance the mechanical properties of the bio-inspired hybrid composite.
基金supported by the National Natural Science Foundation of China(Nos.51772247 and 5172780072)the Creative Research Foundation of Science and Technology on Thermostructural Composite Materials Laboratory(No.6142911050217)the Natural Science Basic Research Plan in Shaanxi Province of China(No.2017JM5098)。
文摘SiC nanowires reinforced C/(PyC-SiC)_(n)multilayered matrix composites(SM-CS for short)were prepared by combined with sol-gel and chemical vapor infiltration(CVI)method.Firstly,(PyC-Si OC);multilayered structure was formed by cycles of impregnation and deposition.Then SiOC was transformed into SiC by heat-treatment,and(PyC-SiC)_(n)multilayered structure would be obtained.At the same time,the PyC layer which was designed as the outmost layer could decrease gas supersaturation to form in-situ tubular SiC nanowires on the surface of multilayered structure.The results of three-point bending test showed that the maximum force of SM-CS composites was increased by the number of cycles of the preparation process,which were up to enhanced by 74.38%compared with C/C composite materials.The fracture surface showed that the improvement was due to the multiscale reinforcing system of(PyC-SiC)_(n)multilayered structure and SiC nanowires.Multilayered structure can protect carbon fibers and release stress concentration by induction of cracks.And the mechanical interlocking effect of SiC nanowires could reinforce bonding force of the remaining matrix.
基金Projects(51278209 and 51478047) supported by the National Natural Science Foundation of ChinaProject(ZQN-PY110) supported by Promotion Program for Young and Middle-aged Teacher in Science and Technology Research of Huaqiao University,China+1 种基金Project(2014FJ-NCET-ZR03) supported by Program for New Century Excellent Talents in Fujian Province University,ChinaProject(JA13005) supported by Incubation Programme for Excellent Young Science and Technology Talents in Fujian Province Universities,China
文摘The static test of 13 square hollow section(SHS) X-joints with different β and different types of plate reinforcement under in-plane moment in brace was carried out. Experimental test schemes, failure modes of specimens, moment-vertical displacement curves, moment-deformation of the chord, and strain strength distribution curves were presented. The effect of β and plate reinforcement types on in-plane flexural property of SHS X-joints was studied. Results show that punching shear of chord face disappears, brace material fracture appears and concave and convex deformation of chord decrease when either collar plates or doubler plates were welded on chord face. Moment-vertical displacement curves of all specimens have obvious elastic, elastic-plastic and plastic stages. As β increases, the in-plane flexural ultimate capacity and initial stiffness of joints of the same plate reinforcement type increase, but ductility of joints decreases. With the same β, the in-plane flexural initial stiffness and ultimate capacity of doubler plate reinforced joints, collar plate reinforced joints, and unreinforced joints decrease progressively. Thickness of reinforcement plate has no obvious effect on in-plane flexural initial stiffness and ultimate capacity of joints. As thickness of reinforcement plate increases, the ductility of reinforced X-joints decreases. The concave and convex deformation of every specimen has good symmetry;as β increases, the yield and ultimate deformation of chord decrease.
基金Funded by the National Natural Science Foundation of China(No.51001117)
文摘Ultra-high molecular weight polyethylene（UHMWPE） fiber/epoxy composites were fabricated by a vacuum assisted resin infused（VARI） processing technology. The curing condition of composites was at a cure temperature of 80 ℃ for 3h in a drying oven. The characteristics of 2.5D（shallow bend-joint and deep straight-joint） structure and 3D orthogonal structure were compared. The failure behavior, flexural strength, and microstructures of both composites were investigated. It was found that the flexural property was closely related to undulation angle θ. The flexural strength of 3D orthogonal structure composite was superior to the other two structures composites with the same weave parameters and resin.
文摘This study reports the investigations for repair of thermoplastic based automotive bumpers and bars with modified friction stir welding(MFSW)process.For MFSW,consumable tool of polyamide6(PA6)composite has been used for joining of acrylonitrile butadiene styrene(ABS)composites.The dissimilar thermoplastics were processed for maintaining a useful range of melt flow properties followed by preparation of feed stock filament for fused deposition modeling(FDM)process through screw extrusion.Finally,3D printed PA6 based consumable rapid tool(RT)was prepared for MFSW.The joints prepared were subjected to flexural,hardness,morphological and thermal testing.The study has suggested the that maximum mechanical strength was obtained for sample welded at 1400 r/min,50 mm/min transverse speed and 3 mm plunge depth,whereas the minimum mechanical strength was obtained for sample welded at 1000 r/min,30 mm/min transverse speed and 2 mm plunge depth.The results are also supported with thermal analysis and photomicrographs.
