An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing lit...An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.展开更多
There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to...There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to determine the number of fixtures is ignored.In most cases,the number of fixtures located on large thin-walled parts is determined based on engineering experience,which leads to huge fixture number and extra waste.Therefore,this paper constructs an optimization model to minimize the number of fixtures.The constraints are set in the optimization model to ensure that the part deformation is within the surface profile tolerance.In addition,the assembly gap between two parts is also controlled.To conduct the optimization,this paper develops an improved particle swarm optimization(IPSO)algorithm by integrating the shrinkage factor and adaptive inertia weight.In the algorithm,particles are encoded according to the fixture position.Each dimension of the particle is assigned to a sub-region by constraining the optional position range of each fixture to improve the optimization efficiency.Finally,a case study on ship curved panel assembly is provided to prove that our method can optimize the number of fixtures while meeting the assembly quality requirements.This research proposes a method to optimize the number of fixtures,which can reduce the number of fixtures and achieve deformation control at the same time.展开更多
Aiming at the problems of long time and poor machining precision in processing the tractor lever workpiece,a special fixture suitable for the tractor lever workpiece is designed by analyzing the processing technology ...Aiming at the problems of long time and poor machining precision in processing the tractor lever workpiece,a special fixture suitable for the tractor lever workpiece is designed by analyzing the processing technology of the lever workpiece,and the workpiece is accurately positioned and tightened under the action of the special fixture.Efficient machining of the workpiece can be achieved by using a drill template.The fixture not only has the advantages of high production efficiency,low cost and high life,but also effectively improves the processing technology of the workpiece,and has certain reference value for the subsequent fixture improvement design.展开更多
This paper focuses on the design of fixtures for NP2 and NP4 cylinder heads on a horizontal machining center of flexible machining automatic lines.It began with an analysis of the diagrams of part processing and worki...This paper focuses on the design of fixtures for NP2 and NP4 cylinder heads on a horizontal machining center of flexible machining automatic lines.It began with an analysis of the diagrams of part processing and working procedure which formed the basis for the design of the processing technology scheme,a selection of suitable machine tools,and the setting of processing parameters.Fixtures tailored to the chosen machine tools were then designed to meet the processing requirements.Additional aspects of the project included the design of part drawings,calculation of working time quota,design of auxiliary guides,support clamping,and hydraulic circuits,all aimed at fulfilling practical production requirements.展开更多
The computer numerical control（CNC） system is suited to control varied types of flexible fixtures in aircraft component manufacturing and assembly. The mechanisms and control requirements of flexible fixtures are pr...The computer numerical control（CNC） system is suited to control varied types of flexible fixtures in aircraft component manufacturing and assembly. The mechanisms and control requirements of flexible fixtures are presented and analyzed. The hardware and software architecture and implementation of CNC system are pro- posed. The flexible fixture mechanism is described using configuration parameters. According to the parameters, the CNC system automatically generates the control feature and the human machine interface （HMI） operation function. The CNC system is implemented in a flexible fixture for skin-strlnger assembly, and results show the effectiveness of the system.展开更多
Low stiffness and positioning problems are difficulties and challenges in the precise machining of near-net-shaped blades.This paper aims to achieve high accuracy in manufacturing by fixture-and deformation-control in...Low stiffness and positioning problems are difficulties and challenges in the precise machining of near-net-shaped blades.This paper aims to achieve high accuracy in manufacturing by fixture-and deformation-control in the adaptive CNC machining process.Adaptive CNC machining technology is first analyzed,and new fixture-evaluation criteria and methods to evaluate the adaptive CNC machining process fixture design are built.Second,a machining fixture is designed and manufactured after analyzing its positioning scheme,clamping scheme,materials(PEEK-GF30),and structure characteristics.Finally,the designed fixture is analyzed by FEA and experimentally verified by a cutting experiment.The results show that the deformation of the blade is an overall rigid-body displacement,the main deformation of the blade-fixture system occurs on the four clamping heads,and this fixture can effectively protect the blade from local deformation.The proposed clamping-sequence method reliably and effectively controls the local maximum deformation of the blade.The system stiffness is increased by 20 Hz,with each clamping force increased by 200 N.Both high-and low-frequency displacement in roughing milling or finishing milling are acceptable relative to the accuracy demand of blade machining.This fixture and an adaptive CNC machining process can achieve high accuracy in blade manufacturing.展开更多
In order to realize the agility of the fixture design, such as reconfigurability, rescalability and reusability, fixture structure is function unit based decomposed from a fire new point of view. Which makes it easy f...In order to realize the agility of the fixture design, such as reconfigurability, rescalability and reusability, fixture structure is function unit based decomposed from a fire new point of view. Which makes it easy for agile fixture to be reconfigured and modified. Thereby, the base of case based agile fixture design system info is established.Whole case based agile fixture design model is presented. In which, three modules are added relative to the other models, including case matching of fixture planning module, conflict arbitration module and agile fixture case modify module. The three modules could solve the previous problem that the experience and result are difficult to be reused in the process of design.Two key techniques in the process of the agile fixture design, the evaluation of case similarity, and restriction based conflict arbitration, are listed. And some methods are presented to evaluate the similarity and clear up the conflict.展开更多
Automation in the layout of fixture components is important to achieve efficiency and flexibility in computer aided fixture design. Based on basic genetic algorithm and particulars of different fixture components, a m...Automation in the layout of fixture components is important to achieve efficiency and flexibility in computer aided fixture design. Based on basic genetic algorithm and particulars of different fixture components, a method of layout space division is presented. Such techniques as suitable crossover rate, mutation rate and selection arithmetic element are adopted in the genetic operation. The results show that genetic algorithm can effectively be applied in the automatic layout of fixture components.展开更多
Error modelling and compensating technology is an effective method to improve the processing precision.The position and orientation deviation of workpiece is caused by the fixing and manufacturing errors of the fixtur...Error modelling and compensating technology is an effective method to improve the processing precision.The position and orientation deviation of workpiece is caused by the fixing and manufacturing errors of the fixture.How to reduce the position and orientation deviation of workpiece has become a technical problem of improving the processing quality of workpiece.In order to increase machining accuracy,an implementation scheme of fixture system comprehensive errors（FSCE） compensation is proposed.A FSCE parameter model is established by analyzing the influence of contact points on the position and orientation of workpiece.Meanwhile,a parameter identification method for FSCE parameter model is presented by using the 3-2-1 deterministic positioning fixture,which determines the model parameters.Moreover,a FSCE compensation model is formulated to study the compensation value of the cutting position.By using RenishawOMP60 Probe and combining vertical machining centre（SKVH850） equipment with SKY2001 Open CNC System,on-machine verification system（OMVS） is built to measure FSCE successfully.The processing error can be reduced by analyzing the cutting position of the tool with the homogeneous transformation of space coordinate system.Finally,the compensation experiment of real time errors is conducted,and the cylindricality and perpendicularity errors of hole surface are reduced by 30.77% and 28.57%,respectively.This paper provides a new way of realizing the compensation of FCSE,which can improve the machining accuracy of workpiece largely.展开更多
'N-2-1' principle is widely recognized in the fixture design for deformablesheet metal workpieces, where N, the locators on primary datum, is the key to sheet metal fixturedesign. However, little research is d...'N-2-1' principle is widely recognized in the fixture design for deformablesheet metal workpieces, where N, the locators on primary datum, is the key to sheet metal fixturedesign. However, little research is done on how to determine the positions and the number of Nlocators. In practice, the N locators are frequently designed from experience, which is oftenunsatisfactory for achieving the precision requirement in fixture design. A new method to lay outthe N locators for measuring fixture of deformable sheet metal workpiece is presented, given thefixed number of A'. Finite-element method is used to model and analysis the deformation of differentlocator layouts. A knowledge based genetic algorithm (KBGA) is applied to identify the optimumlocator layout for measuring fixture design. An example of a door outer is used to verify theoptimization approach.展开更多
Based on the features of the design and assembly of rnodular fixtures, a new design system which combines intelligent selection of elements and interactive assembly is presented.Using the fixture design datum, the sys...Based on the features of the design and assembly of rnodular fixtures, a new design system which combines intelligent selection of elements and interactive assembly is presented.Using the fixture design datum, the system can automatically select elements,and can interactively assemble together these elements based on AutoCAD. An example is given to illustrate it.展开更多
A searching-machining system of RL & SM (Rapid Location and State Memory) universal fixture is here introduced, and the concept of rapid searching technology and manufacturing information transformation is then de...A searching-machining system of RL & SM (Rapid Location and State Memory) universal fixture is here introduced, and the concept of rapid searching technology and manufacturing information transformation is then described, with the appropriate control methods and key techniques for its realization being proposed and also practically realized. Theoretical analysis and experimental results show that the proposed idea and methods are feasible to serve as in the practical application of the RL & SM system.展开更多
An automotive body is composed of compliant sheet metal parts.Fast and exactly diagnosing variation sources is very important when assembly variations happen.This paper proposes a diagnosis method of multi fixture var...An automotive body is composed of compliant sheet metal parts.Fast and exactly diagnosing variation sources is very important when assembly variations happen.This paper proposes a diagnosis method of multi fixture variations based on the variation model of compliant sheet metal assembly.The assembly variation model is obtained by using the method of influence coefficients(MIC) and considering the manufacturing variations of compliant parts and multi fixture variations.The measurement point variations induced by part manufacturing variations are firstly removed from the measurement data.The variation patterns of multi fixture variations are constructed by column vectors of fixture variation sensitivity matrix.This method is proved to be feasible for exactly diagnosing the fixture variations and has higher diagnosis efficiency than designated component analysis(DCA).展开更多
A numerical model is established by Abaqus software for superalloy during tungsten inert gas （TIG） welding with welding fixture to simulate the weld temperature filed, stress and strain field, and weld plate＇s hori...A numerical model is established by Abaqus software for superalloy during tungsten inert gas （TIG） welding with welding fixture to simulate the weld temperature filed, stress and strain field, and weld plate＇s horizontal trasnsveral shift. The clamp force perpendicular to the weld plate varying with welding time was analyzed. The maximum clamp force during welding process was calculated. Under the condition of insufficient of clamping force, a half or one third of the maximum clamp force for example, the weld plate＇s horizontal transversal displacement could happen and also be computed.展开更多
Fixture locating layout has a direct and influential impact on aeronautical thin-walled component(ATWC)manufacturing quality.The purpose is to develop a topological optimization method for ATWC fixture locating layout...Fixture locating layout has a direct and influential impact on aeronautical thin-walled component(ATWC)manufacturing quality.The purpose is to develop a topological optimization method for ATWC fixture locating layout to minimize the manufacturing deformation.Firstly,a topological optimization model that takes the stiffness of ATWC as the objective function and the volume of the locating structure as the constraint is established.Secondly,ATWC and the locating structure are regarded as an integrated entity,and the variable-density method based topological optimization approach is adopted for the optimization of the locating structure using ABAQUS topology optimization module(ATOM).Thirdly,through a subsequent model reconstruction referring to the obtained topological structure,the optimal fixture locating layout is achieved.Finally,a case study is conducted to verify the proposed method and the comparison results with firefly algorithm(FA)coupled with finite element analysis(FEA)indicate that the number and positions of the locators for ATWC can be optimized simultaneously and successfully by the proposed topological optimization model.展开更多
Based on an example of its typical structure, the concept of modular fixture structure module is presented, and the structure module system of modular fixture is summarized. Then the parametric design of structure is ...Based on an example of its typical structure, the concept of modular fixture structure module is presented, and the structure module system of modular fixture is summarized. Then the parametric design of structure is discussed, and its advantages are also emphasized.Furthermore, some specific methods are provided, such as the selection of fixture components, the determination and input of parameters, drawing representative model,and the creation of drawing. Finally an applied example of strcture parametric design is presented.展开更多
In order to develop an intelligent case-based reasoning （CBR） system to reuse fixture de- sign knowledge, ontology technology was integrated in CBR system by semantic annotation of fixture design case. Domain ontolo...In order to develop an intelligent case-based reasoning （CBR） system to reuse fixture de- sign knowledge, ontology technology was integrated in CBR system by semantic annotation of fixture design case. Domain ontology of fixture design was constructed; concepts and relations were de- fined and represented. The 2-level similarity evaluation approach of domain ontology was presented. The concept similarity of cases was calculated as the first grade case retrieval. Numerical measure- ment was the second grade case retrieval, which adopted various methods to calculate different types of attribute values. The problem of similarity measurement of fixture design case was resolved. Pro- totype system based on the proposed method was illustrated and the retrieval approach was proved to be efficient.展开更多
A new fixture system-Rapid Location and State Memory (RL&SM) fixture system is presented.It is based on RFPE technique.In which a new method-adaptable location system is used to locating arbitrarily shapedpart.It ...A new fixture system-Rapid Location and State Memory (RL&SM) fixture system is presented.It is based on RFPE technique.In which a new method-adaptable location system is used to locating arbitrarily shapedpart.It solves the problems of part location,stock driftand accessibility of all sides of the part in machining.Any part can be machined entirely in a single setup by an appropriate machine tool.RL&SM fixture system consists of four parts:state memory,setup,data measure and information handling.The principle,components and work process of it are discussed,and some of the key techniques for industrialization are also presented.Keywords:Universal fixture,Rapid location,State memo-展开更多
The effect of welding jig on the welding stress and buckling distortion of thin aluminum plate joints was simulated by finite element method （FEM）. The results show that the restraint distance and the heat conductio...The effect of welding jig on the welding stress and buckling distortion of thin aluminum plate joints was simulated by finite element method （FEM）. The results show that the restraint distance and the heat conduction ability of the fixture do have essential effects on the residual stress and distortion. The residual compressive stress and distortion will be increasing with the increase of the restraint distance, while the residual compressive stress and distortion will be decreasing with the increase of the heat conduction ability of the fixture.展开更多
Fixture design and planning is one of the most important manufacturing activities, playing a pivotal role in deciding the lead time for product development. Fixture design, which affects the part-quality in terms of g...Fixture design and planning is one of the most important manufacturing activities, playing a pivotal role in deciding the lead time for product development. Fixture design, which affects the part-quality in terms of geometric accuracy and surface finish, can be enhanced by using the product manufacturing information(PMI) stored in the neutral standard for the exchange of product model data(STEP) file, thereby integrating design and manufacturing. The present paper proposes a unique fixture design approach, to extract the geometry information from STEP application protocol(AP) 242 files of computer aided design(CAD) models, for providing automatic suggestions of locator positions and clamping surfaces. Automatic feature extraction software "FiXplan", developed using the programming language C#, is used to extract the part feature, dimension and geometry information. The information from the STEP AP 242 file is deduced using geometric reasoning techniques, which in turn is utilized for fixture planning. The developed software is observed to be adept in identifying the primary, secondary, and tertiary locating faces and locator position configurations of prismatic components. Structural analysis of the prismatic part under different locator positions was performed using commercial finite element method software, ABAQUS, and the optimized locator position was identified on the basis of minimum deformation of the workpiece.The area-ratio(base locator enclosed area(%)/work piece base area(%)) for the ideal locator configuration was observed as 33%. Experiments were conducted on a prismatic workpiece using a specially designed fixture, for different locator configurations. The surface roughness and waviness of the machined surfaces were analysed using an Alicona non-contact optical profilometer. The best surface characteristics were obtained for the surface machined under the ideal locator positions having an area-ratio of 33%, thus validating the predicted numerical results. The efficiency, capability and applicability of the developed software is demonstrated for the finishing operation of a sensor cover – a typical prismatic component having applications in the naval industry, under different locator configurations.The best results were obtained under the proposed ideal locator configuration of area-ratio 33%.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.52005371)Shanghai Municipal Natural Science Foundation of China(Grant No.22ZR1463900)+1 种基金Fundamental Research Funds for the Central Universities of China(Grant No.22120220649)State Key Laboratory of Mechanical System and Vibration of China(Grant No.MSV202318).
文摘An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.
基金Supported by National Natural Science Foundation of China(Grant No.52005371)Shanghai Pujiang Program of China(Grant No.2020PJD071)+1 种基金Shanghai Municipal Natural Science Foundation of China(Grant No.22ZR1463900)Fundamental Research Funds for the Central Universities of China.
文摘There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to determine the number of fixtures is ignored.In most cases,the number of fixtures located on large thin-walled parts is determined based on engineering experience,which leads to huge fixture number and extra waste.Therefore,this paper constructs an optimization model to minimize the number of fixtures.The constraints are set in the optimization model to ensure that the part deformation is within the surface profile tolerance.In addition,the assembly gap between two parts is also controlled.To conduct the optimization,this paper develops an improved particle swarm optimization(IPSO)algorithm by integrating the shrinkage factor and adaptive inertia weight.In the algorithm,particles are encoded according to the fixture position.Each dimension of the particle is assigned to a sub-region by constraining the optional position range of each fixture to improve the optimization efficiency.Finally,a case study on ship curved panel assembly is provided to prove that our method can optimize the number of fixtures while meeting the assembly quality requirements.This research proposes a method to optimize the number of fixtures,which can reduce the number of fixtures and achieve deformation control at the same time.
基金supported by the Henan Natural Science Foundation (No.222300420168)the Natural Science Foundation of Henan Polytechnic University (B2021-31)Fundamental Research Funds for the Universities of Henan Province (No.NSFRF220415).
文摘Aiming at the problems of long time and poor machining precision in processing the tractor lever workpiece,a special fixture suitable for the tractor lever workpiece is designed by analyzing the processing technology of the lever workpiece,and the workpiece is accurately positioned and tightened under the action of the special fixture.Efficient machining of the workpiece can be achieved by using a drill template.The fixture not only has the advantages of high production efficiency,low cost and high life,but also effectively improves the processing technology of the workpiece,and has certain reference value for the subsequent fixture improvement design.
文摘This paper focuses on the design of fixtures for NP2 and NP4 cylinder heads on a horizontal machining center of flexible machining automatic lines.It began with an analysis of the diagrams of part processing and working procedure which formed the basis for the design of the processing technology scheme,a selection of suitable machine tools,and the setting of processing parameters.Fixtures tailored to the chosen machine tools were then designed to meet the processing requirements.Additional aspects of the project included the design of part drawings,calculation of working time quota,design of auxiliary guides,support clamping,and hydraulic circuits,all aimed at fulfilling practical production requirements.
文摘The computer numerical control（CNC） system is suited to control varied types of flexible fixtures in aircraft component manufacturing and assembly. The mechanisms and control requirements of flexible fixtures are presented and analyzed. The hardware and software architecture and implementation of CNC system are pro- posed. The flexible fixture mechanism is described using configuration parameters. According to the parameters, the CNC system automatically generates the control feature and the human machine interface （HMI） operation function. The CNC system is implemented in a flexible fixture for skin-strlnger assembly, and results show the effectiveness of the system.
基金supported in part by Xi’an Aero-Engine(Group)Ltd.National Key Scientific Instrument and Equipment Development Project(2016YFF0101900)+1 种基金National Natural Science Foundation of China(Grant 51575310)Beijing Municipal Natural Science Foundation(Grant 3162014)。
文摘Low stiffness and positioning problems are difficulties and challenges in the precise machining of near-net-shaped blades.This paper aims to achieve high accuracy in manufacturing by fixture-and deformation-control in the adaptive CNC machining process.Adaptive CNC machining technology is first analyzed,and new fixture-evaluation criteria and methods to evaluate the adaptive CNC machining process fixture design are built.Second,a machining fixture is designed and manufactured after analyzing its positioning scheme,clamping scheme,materials(PEEK-GF30),and structure characteristics.Finally,the designed fixture is analyzed by FEA and experimentally verified by a cutting experiment.The results show that the deformation of the blade is an overall rigid-body displacement,the main deformation of the blade-fixture system occurs on the four clamping heads,and this fixture can effectively protect the blade from local deformation.The proposed clamping-sequence method reliably and effectively controls the local maximum deformation of the blade.The system stiffness is increased by 20 Hz,with each clamping force increased by 200 N.Both high-and low-frequency displacement in roughing milling or finishing milling are acceptable relative to the accuracy demand of blade machining.This fixture and an adaptive CNC machining process can achieve high accuracy in blade manufacturing.
文摘In order to realize the agility of the fixture design, such as reconfigurability, rescalability and reusability, fixture structure is function unit based decomposed from a fire new point of view. Which makes it easy for agile fixture to be reconfigured and modified. Thereby, the base of case based agile fixture design system info is established.Whole case based agile fixture design model is presented. In which, three modules are added relative to the other models, including case matching of fixture planning module, conflict arbitration module and agile fixture case modify module. The three modules could solve the previous problem that the experience and result are difficult to be reused in the process of design.Two key techniques in the process of the agile fixture design, the evaluation of case similarity, and restriction based conflict arbitration, are listed. And some methods are presented to evaluate the similarity and clear up the conflict.
文摘Automation in the layout of fixture components is important to achieve efficiency and flexibility in computer aided fixture design. Based on basic genetic algorithm and particulars of different fixture components, a method of layout space division is presented. Such techniques as suitable crossover rate, mutation rate and selection arithmetic element are adopted in the genetic operation. The results show that genetic algorithm can effectively be applied in the automatic layout of fixture components.
基金supported by National Natural Science Foundation of China (Grant No. 50975200)National Key Technologies R & D Programmer of China (Grant No. 2009ZX04014-021)
文摘Error modelling and compensating technology is an effective method to improve the processing precision.The position and orientation deviation of workpiece is caused by the fixing and manufacturing errors of the fixture.How to reduce the position and orientation deviation of workpiece has become a technical problem of improving the processing quality of workpiece.In order to increase machining accuracy,an implementation scheme of fixture system comprehensive errors（FSCE） compensation is proposed.A FSCE parameter model is established by analyzing the influence of contact points on the position and orientation of workpiece.Meanwhile,a parameter identification method for FSCE parameter model is presented by using the 3-2-1 deterministic positioning fixture,which determines the model parameters.Moreover,a FSCE compensation model is formulated to study the compensation value of the cutting position.By using RenishawOMP60 Probe and combining vertical machining centre（SKVH850） equipment with SKY2001 Open CNC System,on-machine verification system（OMVS） is built to measure FSCE successfully.The processing error can be reduced by analyzing the cutting position of the tool with the homogeneous transformation of space coordinate system.Finally,the compensation experiment of real time errors is conducted,and the cylindricality and perpendicularity errors of hole surface are reduced by 30.77% and 28.57%,respectively.This paper provides a new way of realizing the compensation of FCSE,which can improve the machining accuracy of workpiece largely.
基金This project is supported by Overseas Young Scientists Cooperation of National Natural Science Foundation of China (No.59958204) National Natural Science Foundation of China (No.50175071). :
文摘'N-2-1' principle is widely recognized in the fixture design for deformablesheet metal workpieces, where N, the locators on primary datum, is the key to sheet metal fixturedesign. However, little research is done on how to determine the positions and the number of Nlocators. In practice, the N locators are frequently designed from experience, which is oftenunsatisfactory for achieving the precision requirement in fixture design. A new method to lay outthe N locators for measuring fixture of deformable sheet metal workpiece is presented, given thefixed number of A'. Finite-element method is used to model and analysis the deformation of differentlocator layouts. A knowledge based genetic algorithm (KBGA) is applied to identify the optimumlocator layout for measuring fixture design. An example of a door outer is used to verify theoptimization approach.
文摘Based on the features of the design and assembly of rnodular fixtures, a new design system which combines intelligent selection of elements and interactive assembly is presented.Using the fixture design datum, the system can automatically select elements,and can interactively assemble together these elements based on AutoCAD. An example is given to illustrate it.
文摘A searching-machining system of RL & SM (Rapid Location and State Memory) universal fixture is here introduced, and the concept of rapid searching technology and manufacturing information transformation is then described, with the appropriate control methods and key techniques for its realization being proposed and also practically realized. Theoretical analysis and experimental results show that the proposed idea and methods are feasible to serve as in the practical application of the RL & SM system.
基金the National Natural Science Foundation of China (No. 50705056)the National High Technology Research and Development Program (863) of China (No.2006AA04Z148)
文摘An automotive body is composed of compliant sheet metal parts.Fast and exactly diagnosing variation sources is very important when assembly variations happen.This paper proposes a diagnosis method of multi fixture variations based on the variation model of compliant sheet metal assembly.The assembly variation model is obtained by using the method of influence coefficients(MIC) and considering the manufacturing variations of compliant parts and multi fixture variations.The measurement point variations induced by part manufacturing variations are firstly removed from the measurement data.The variation patterns of multi fixture variations are constructed by column vectors of fixture variation sensitivity matrix.This method is proved to be feasible for exactly diagnosing the fixture variations and has higher diagnosis efficiency than designated component analysis(DCA).
基金supported by the National Natural Science Foundation of China(Grant No.51275496)
文摘A numerical model is established by Abaqus software for superalloy during tungsten inert gas （TIG） welding with welding fixture to simulate the weld temperature filed, stress and strain field, and weld plate＇s horizontal trasnsveral shift. The clamp force perpendicular to the weld plate varying with welding time was analyzed. The maximum clamp force during welding process was calculated. Under the condition of insufficient of clamping force, a half or one third of the maximum clamp force for example, the weld plate＇s horizontal transversal displacement could happen and also be computed.
基金supported by the National Natural Science Foundation of China(No.51375396)the Shaanxi Science and Technology Innovation Project Plan,China(No.2016KTCQ01-50)
文摘Fixture locating layout has a direct and influential impact on aeronautical thin-walled component(ATWC)manufacturing quality.The purpose is to develop a topological optimization method for ATWC fixture locating layout to minimize the manufacturing deformation.Firstly,a topological optimization model that takes the stiffness of ATWC as the objective function and the volume of the locating structure as the constraint is established.Secondly,ATWC and the locating structure are regarded as an integrated entity,and the variable-density method based topological optimization approach is adopted for the optimization of the locating structure using ABAQUS topology optimization module(ATOM).Thirdly,through a subsequent model reconstruction referring to the obtained topological structure,the optimal fixture locating layout is achieved.Finally,a case study is conducted to verify the proposed method and the comparison results with firefly algorithm(FA)coupled with finite element analysis(FEA)indicate that the number and positions of the locators for ATWC can be optimized simultaneously and successfully by the proposed topological optimization model.
文摘Based on an example of its typical structure, the concept of modular fixture structure module is presented, and the structure module system of modular fixture is summarized. Then the parametric design of structure is discussed, and its advantages are also emphasized.Furthermore, some specific methods are provided, such as the selection of fixture components, the determination and input of parameters, drawing representative model,and the creation of drawing. Finally an applied example of strcture parametric design is presented.
基金Supported by the Ministerial Level Advanced Research Foundation of China(513180102)the National Defense Basic Research undation of China(A2220110001)
文摘In order to develop an intelligent case-based reasoning （CBR） system to reuse fixture de- sign knowledge, ontology technology was integrated in CBR system by semantic annotation of fixture design case. Domain ontology of fixture design was constructed; concepts and relations were de- fined and represented. The 2-level similarity evaluation approach of domain ontology was presented. The concept similarity of cases was calculated as the first grade case retrieval. Numerical measure- ment was the second grade case retrieval, which adopted various methods to calculate different types of attribute values. The problem of similarity measurement of fixture design case was resolved. Pro- totype system based on the proposed method was illustrated and the retrieval approach was proved to be efficient.
基金Supported by national high technology development plan(863-511-943-010)
文摘A new fixture system-Rapid Location and State Memory (RL&SM) fixture system is presented.It is based on RFPE technique.In which a new method-adaptable location system is used to locating arbitrarily shapedpart.It solves the problems of part location,stock driftand accessibility of all sides of the part in machining.Any part can be machined entirely in a single setup by an appropriate machine tool.RL&SM fixture system consists of four parts:state memory,setup,data measure and information handling.The principle,components and work process of it are discussed,and some of the key techniques for industrialization are also presented.Keywords:Universal fixture,Rapid location,State memo-
文摘The effect of welding jig on the welding stress and buckling distortion of thin aluminum plate joints was simulated by finite element method （FEM）. The results show that the restraint distance and the heat conduction ability of the fixture do have essential effects on the residual stress and distortion. The residual compressive stress and distortion will be increasing with the increase of the restraint distance, while the residual compressive stress and distortion will be decreasing with the increase of the heat conduction ability of the fixture.
基金Department of Science and Technology,Government of India for providing financial support under the scheme FIST(No.SR/FST/ETI-388/2015)。
文摘Fixture design and planning is one of the most important manufacturing activities, playing a pivotal role in deciding the lead time for product development. Fixture design, which affects the part-quality in terms of geometric accuracy and surface finish, can be enhanced by using the product manufacturing information(PMI) stored in the neutral standard for the exchange of product model data(STEP) file, thereby integrating design and manufacturing. The present paper proposes a unique fixture design approach, to extract the geometry information from STEP application protocol(AP) 242 files of computer aided design(CAD) models, for providing automatic suggestions of locator positions and clamping surfaces. Automatic feature extraction software "FiXplan", developed using the programming language C#, is used to extract the part feature, dimension and geometry information. The information from the STEP AP 242 file is deduced using geometric reasoning techniques, which in turn is utilized for fixture planning. The developed software is observed to be adept in identifying the primary, secondary, and tertiary locating faces and locator position configurations of prismatic components. Structural analysis of the prismatic part under different locator positions was performed using commercial finite element method software, ABAQUS, and the optimized locator position was identified on the basis of minimum deformation of the workpiece.The area-ratio(base locator enclosed area(%)/work piece base area(%)) for the ideal locator configuration was observed as 33%. Experiments were conducted on a prismatic workpiece using a specially designed fixture, for different locator configurations. The surface roughness and waviness of the machined surfaces were analysed using an Alicona non-contact optical profilometer. The best surface characteristics were obtained for the surface machined under the ideal locator positions having an area-ratio of 33%, thus validating the predicted numerical results. The efficiency, capability and applicability of the developed software is demonstrated for the finishing operation of a sensor cover – a typical prismatic component having applications in the naval industry, under different locator configurations.The best results were obtained under the proposed ideal locator configuration of area-ratio 33%.
