This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(...This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(200,300,400℃)on their electrochromic properties.The microstructure characterization of WO_(3) films were performed using scanning electron microscope(SEM),X-ray diffraction(XRD),and transmission electron microscope(TEM),and their electrochromic properties were tested by combining an electrochemical workstation with an ultraviolet-visible spectrophotometer.The results showed that the precursor solution concentration directly affected the thickness(290,560,990 nm)and microstructure of WO_(3) films,significantly impacting their electrochromic properties.However,the annealing temperature had a negligible effect.As the precursor solution concentration increased,the optical modulation of WO_(3) films gradually decreased,reaching 51.1%,43.8%,and 35.1%,respectively.The switching time first increased and then stabilized,with coloring times of 7.3,7.7,and 7.7 s,respectively,and bleaching times of 3.8,6.5,and 6.5 s,respectively.The coloration efficiency gradually increased but the increase was relatively small,reaching 41.8,44.4,and 44.8 cm^(2)/C,respectively.Moreover,the cycling stability of WO_(3) films was poor,with the ratios of the final value of optical modulation to the initial value 0.33,0.26,and 0.34,respectively.Additionally,there were bigger differences in the bleached state transmittance,while the colored state transmittance showed smaller variations.However,the former has better cycling stability than the latter.In summary,to obtain better electrochromic properties,the thickness of WO_(3) films should not exceed 290 nm.展开更多
Janus films with asymmetric physical/chemical properties have attracted con siderable attention due to their promising applications in personal thermal management,electronic skin s,sensors,actuators,etc.However,tradit...Janus films with asymmetric physical/chemical properties have attracted con siderable attention due to their promising applications in personal thermal management,electronic skin s,sensors,actuators,etc.However,traditional methods for fabricating Janus films conventionally need the assistance of an interface or auxiliary equipment,which are usually complex and time-consuming.Herein,flexible poly(vinyl alcohol)(PVA)/graphene oxide(GO)/h-BN(recorded as PVA/GO/h-BN)Janus films with thermally,optically,and electrically anisotropic properties are fabricated by a simple density deposition self-assem bly method,which just utilizes the density difference between GO and h-BN during water evaporation.Experimental results show that the two sides of the acquired Janus films have obvious asymmetric characteristics.In the original state of the PVA/GO/h-BN Janus films,the thermal conductivity of the GO side(10.06 W·m^(-1)·K^(-1))is generally lower than that of the h-BN side(10.48W·m^(-1)·K^(-1)).But after GO is reduced,the thermal conductivity of the rGO side reaches 12.17 W·m^(-1)·K^(-1),surpassing that of the h-BN side.In addition,the relative reflectance of the h-BN side of Janus film is also significantly higher than that of the rGO side,and the su rface resistance difference between the two sides is about 4 orders of magnitude.The prepared PVA/GO/h-BN Janus films show great application potential in human thermal management,light conversion switches,and electronic skins.This study provides a simple and versatile strategy for fabricating Janus films with multifunctional(such as thermal,optical,and electrical)anisotropies.展开更多
Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The igniti...Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The ignition resistance of these alloys often depends on the protectiveness of the oxide film formed on the surface.This paper elucidates the formation mechanism of oxide film from thermodynamics and kinetics,classifying oxide films based on their layered structure to assess their protective properties.Furthermore,it comprehensively reviews the impact of characteristics on the protective effectiveness such as compactness,continuity,thickness,and mechanical properties.The paper also introduces various characterization methods for the microstructure and properties of oxide film.The primary objective of this paper is to enhance the comprehension of oxide film concerning the ignition resistance of Mg alloys and to furnish references for future advancements and research in Mg alloys with heightened ignition resistance.展开更多
Because of their low electrical conductivity,sluggish ion diffusion,and poor stability,conventional electrode materials are not able to meet the growing demands of energy storage and portable devices.Graphene assemble...Because of their low electrical conductivity,sluggish ion diffusion,and poor stability,conventional electrode materials are not able to meet the growing demands of energy storage and portable devices.Graphene assembled films(GAFs)formed from graphene nanosheets have an ultrahigh conductivity,a unique 2D network structure,and exceptional mechanical strength,which give them the potential to solve these problems.However,a systematic understanding of GAFs as an advanced electrode material is lacking.This review focuses on the use of GAFs in electrochemistry,providing a comprehensive analysis of their synthesis methods,surface/structural characteristics,and physical properties,and thus understand their structure-property relationships.Their advantages in batteries,supercapacitors,and electrochemical sensors are systematically evaluated,with an emphasis on their excellent electrical conductivity,ion transport kinetics,and interfacial stability.The existing problems in these devices,such as chemical inertness and mechanical brittleness,are discussed and potential solutions are proposed,including defect engineering and hybrid structures.This review should deepen our mechanistic understanding of the use of GAFs in electrochemical systems and provide actionable strategies for developing stable,high-performance electrode materials.展开更多
To advance the understanding of the corrosion behavior of stainless steel bellows in marine atmospheric environments and enhance the precision of service life predictions,this study employs finite element simulations ...To advance the understanding of the corrosion behavior of stainless steel bellows in marine atmospheric environments and enhance the precision of service life predictions,this study employs finite element simulations to investigate the pitting corrosion rates and pit morphologies of bellows peaks and troughs under varying electrolyte film thicknesses.The model incorporates localized electrochemical reactions,oxygen concentration,and homogeneous solution reactions.For improved computational accuracy,the fitted polarization curve data were directly applied as nonlinear boundary conditions on the electrode surface via interpolation functions.Simulation results reveal that the peak regions exhibit faster corrosion rates than the trough regions.With increasing electrolyte film thickness(from 10μm to 500μm),corrosion rates at both peaks and troughs decrease progressively,and after 120 hours of simulation,the maximum corrosion rate at the peaks declines from 0.720 mm/a to 0.130 mm/a,and at the troughs from 0.520 mm/a to 0.120 mm/a,with the disparity in corrosion rates diminishing over time.Furthermore,as corrosion progresses,pits propagate deeper into the substrate,exhibiting both vertical penetration and lateral expansion along the passive film interface,ultimately breaching the substrate.This research offers valuable insights into designing corrosion mitigation strategies for stainless steel bellows in marine environments.展开更多
BACKGROUND Dry eye disease(DED)represents a multifactorial condition characterized by ocular discomfort and visual disturbances.The management of DED relies heavily on accurate diagnosis to tailor effective treatments...BACKGROUND Dry eye disease(DED)represents a multifactorial condition characterized by ocular discomfort and visual disturbances.The management of DED relies heavily on accurate diagnosis to tailor effective treatments.Diagnostic approaches encompass both subjective and objective assessments.AIM To review the diagnostic methods used in the process of dry eye disease management.METHODS A comprehensive review of diagnostic approaches for dry eye was performed using scientific databases.Studies published within the last four years were considered.Studies were excluded if a full text was absent or the article was not written in English.Articles were assessed for relevancy,and a total of 107 studies were selected.The selection method used a systematic methodology,which guaranteed an exhaustive assessment of the diagnostic techniques reported in current literature.The study adheres to principles for systematic reviews ensuring dependability and accuracy.The studies were assessed for emphasize on both novel traditional and diagnostic methods for dry eye disease management.RESULTS Key objective tests include tear break-up time,which evaluates tear film stability;fluorescein and lissamine green staining,which assess ocular surface damage and inflammation;tear osmolarity measurement,indicative of tear film quality;and tear volume assessment via Schirmer's test,which evaluates tear production.Advanced imaging techniques such as optical coherence tomography and meibography offer detailed anatomical insights into the ocular surface and meibomian glands,aiding in the diagnosis of underlying structural abnormalities.Moreover,emerging technologies such as matrix metalloproteinase-9 testing and inflammatory biomarkers provide additional diagnostic precision,particularly in identifying inflammatory components of DED.CONCLUSION Integrating a combination of subjective and objective diagnostic tools allows clinicians to comprehensively assess the condition,tailor treatment plans,and monitor therapeutic efficacy.Continued advancements in diagnostic technologies promise to enhance our understanding and management of this prevalent ocular condition.展开更多
The oral disintegrating film(ODF)offers significant advantages such as superior patient compliance and rapid action onset as a form of solid drug delivery.However,the drug loading efficiency and dosage of the ODF curr...The oral disintegrating film(ODF)offers significant advantages such as superior patient compliance and rapid action onset as a form of solid drug delivery.However,the drug loading efficiency and dosage of the ODF currently available in the market are limited.To enhance the drug loading efficiency,with bacterial cellulose(BC)and hyaluronic acid(HA)as film-forming agents,glycerol(GL)as a plasticizer,and diprophylline(Dilor)as the model drug,a Dilor-ODF was prepared by a solvent casting method for the treatment of acute asthma-related diseases.The BC nano-network structure was utilized to augment the drug loading efficiency of the Dilor-ODF,while HA and GL were used to improve the elongation at break.The disintegration time,drug loading efficiency and drug releasing rate,and tensile properties of the Dilor-ODF were mainly evaluated.The results indicated that the Dilor-ODF exhibited a smooth surface with a uniform thickness and a maximum drug loading efficiency of(51.10±0.08)%.The time for complete disintegration and that for drug release in simulated oral saliva were less than 30 and 90 s,respectively,indicating the effect of rapid release.The tensile strength and elongation at break of the Dilor-ODF were(46.3±2.8)MPa and(1.9±0.2)%,respectively.The thermal decomposition temperature of the Dilor-ODF was higher than 200℃,satisfying subsequent processing demand.展开更多
Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface...Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.展开更多
CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly co...CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly controlled by the ion-by-ion growth mechanism at the beginning of the film deposition, then the cluster-by-cluster mechanism came to be dominant. The growth rate increased faster with the increasing of temperature until the thickness reached the limitation, then thickness instead become thinner. The scanning electron micro- scope results revealed that the morphology of the CdS film changed from pinholes to rough, inhomogeneous surface with increasing deposition time and deposition temperature. The X- ray diffraction results showed the film structure was a mixture of two phases： hexagonal and cubic, and it was very important to controll deposition time to the film＇s crystal phase. All films in depth of approxilnate 100 nm existed above 65% transmittance, the absorption edge became ＂red-shift＂ with temperature rising. At 60 and 70℃, with 20 min deposited-time, the energy band gap was more than 2.42 eV and decreased with time, while at 80 and 90℃ the energy band gap was less than 2.42 eV and increased little when the time changed from 10min to 15 nfin at 80℃.展开更多
Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were...Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.展开更多
Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic fo...Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.展开更多
Zn-doped TiO2 (Zn?TiO2) thin films were prepared by the sol?gel method on titanium substrates with heat treatment at different temperatures. The effects of heat treatment temperatures and Zn doping on the structure, p...Zn-doped TiO2 (Zn?TiO2) thin films were prepared by the sol?gel method on titanium substrates with heat treatment at different temperatures. The effects of heat treatment temperatures and Zn doping on the structure, photocathodic protection and photoelectrochemical properties of TiO2 thin films were investigated. It is indicated that the photoelectrical performance of the Zn?TiO2 films is enhanced with the addition of Zn element compared with the pure-TiO2 film and the largest decline by 897 mV in the electrode potential is achieved under 300 °C heat treatment. SEM?EDS analyses show that Zn element is unevenly distributed in Zn?TiO2 films; XRD patterns reveal that the grain size of Zn?TiO2 is smaller than that of pure-TiO2; FTIR results indicate that Zn - O bond forms on Zn?TiO2 surface. Ultraviolet visible absorption spectra prove that Zn?TiO2 shifts to visible light region.Mott?Shottky curves show that the flat-band potential of Zn?TiO2 is more negative and charge carrier density is bigger than that ofpure-TiO2, implying that under the synergy of the width of the space-charge layer, carrier density and flat-band potential, Zn?TiO2 with 300 °C heat treatment displays the best photocathodic protection performance.展开更多
Propagation characteristics of surface acoustic waves（SAWs） in ZnO films/glass substrates are theoretically investigated by the three-dimensional（3D） finite element method. At first, for（11ˉ20） ZnO films/glass ...Propagation characteristics of surface acoustic waves（SAWs） in ZnO films/glass substrates are theoretically investigated by the three-dimensional（3D） finite element method. At first, for（11ˉ20） ZnO films/glass substrates, the simulation results confirm that the Rayleigh waves along the [0001] direction and Love waves along the [1ˉ100] direction are successfully excited in the multilayered structures. Next, the crystal orientations of the ZnO films are rotated, and the influences of ZnO films with different crystal orientations on SAW characterizations, including the phase velocity, electromechanical coupling coefficient, and temperature coefficient of frequency, are investigated. The results show that at appropriate h/λ, Rayleigh wave has a maximum k^2 of 2.4% in（90°, 56.5°, 0°） ZnO film/glass substrate structure; Love wave has a maximum k^2 of 3.81% in（56°, 90°, 0°） ZnO film/glass substrate structure. Meantime, for Rayleigh wave and Love wave devices, zero temperature coefficient of frequency（TCF） can be achieved at appropriate ratio of film thickness to SAW wavelength. These results show that SAW devices with higher k^2 or lower TCF can be fabricated by flexibly selecting the crystal orientations of ZnO films on glass substrates.展开更多
Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the densi...Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the density of the PZT film are measured respectively.Bimorph- type bending actuators are fabricated using these films. The model, which is used toanalyze the driving ability of bimorph-type bending actuators by hydrothermal method, is set up. Itcan be seen that the driving ability of bimorph-type bending actuators can be greatly improved byoptimizing the thickness of PZT thin film and substrate from the theoretical analysis results. Themeasured values are expected to agree with the theoretical values calculated by the above model.展开更多
The effect of different annealing temperatures on the structure, morphology,and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated.Zinc-oxide thin films were coated on quart...The effect of different annealing temperatures on the structure, morphology,and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated.Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absoluteethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. Theresults show that ZnO films derived from zinc-citrate have lower crystallization temperature (below400℃), and that the crystal structure is wurtzite. The films, treated over 500℃, consist ofnano-particles and show to be porous at 600℃. The particle size of the film increases with theincrease of the annealing temperature. The largest particle size is 60 nm at 600℃. The opticaltransmittances related to the annealing temperatures become 90% higher in the visible range. Thefilm shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at500℃) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).展开更多
ZnO film with claviform structure was synthesized on quartz substrates through a hydrothermal method at 90℃. The microstructure of the film is composed of clusters of submicrometer rods, which therefore endues the fi...ZnO film with claviform structure was synthesized on quartz substrates through a hydrothermal method at 90℃. The microstructure of the film is composed of clusters of submicrometer rods, which therefore endues the film with good superhydrophobicity. Meanwhile, the film with such tanglesome structure also shows highly crystalline quality testified by a strong ultra-violet （UV） emission and very low deep-level emission observed on the photoluminescence （PL） spectrum as well as high transparence of about 89% transmittance in visible light range.展开更多
Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structure...Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structures of thermoelectric films,the potential applications of thermoelectric materials are diversified,particularly in microdevices.Well-controlled nanostructures in thermoelectric films are effective to optimize the electrical and thermal transport,which can significantly improve the performance of thermoelectric materials.In this paper,various physical and chemical approaches to fabricate thermoelectric films,including inorganic,organic,and inorganic–organic composites,are summarized,where more attentions are paid on the inorganic thermoelectric films for their excellent thermoelectric responses.Additionally,strategies for enhancing the performance of thermoelectric films are also discussed.展开更多
CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were inves...CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were investigated by XRD, SEM, XPS, AFM and UV-VIS. The resultsshowed that the thin films are uniform, compact and good in adhesion to the substrates, and thegrowth of the films is 2.8 nm/cycle. The evolution of structure undergoes from the cubic structureto the hexagonal one with a preferred orientation along the (002) plane after annealing at 673 K. Anamount of C, O and Cl impurities can be reduced by increasing the drying temperature or byannealing in N2 atmosphere. It was found that the band gap of the CdS films shifts to higherwavelength after annealing or increasing film thickness. The electrical resistivity decreases withincreasing annealing temperature and film thickness.展开更多
RuS_2 thin films were prepared by the cost-effective chemicalmethod―successive ionic layer adsorption and reaction (SILAR). The structural, optical, andelectrical properties were investigated using X-ray diffraction,...RuS_2 thin films were prepared by the cost-effective chemicalmethod―successive ionic layer adsorption and reaction (SILAR). The structural, optical, andelectrical properties were investigated using X-ray diffraction, scanning electron microscopy,optical transmittance, and electrical resistivity methods. The results indicate that the films arehomogeneous and dense; the structure of the as-deposited films is amorphous and they crystallizeafter annealed at 500℃ for 30 min. The band gap of the as-deposited films is found to be 1.85 eV,and the electrical resistivity of them is in the order of 10~5 Ω·cm.展开更多
Well-crystallized MgZnO alloy thin films with hexagonal wurtzite structure were fabricated by sol-gel method. With the band gap increases, the surface roughness and the grain size reduces. It is worth noting that the ...Well-crystallized MgZnO alloy thin films with hexagonal wurtzite structure were fabricated by sol-gel method. With the band gap increases, the surface roughness and the grain size reduces. It is worth noting that the intensity of the band-edge luminescence of Mg doped films enhances with the increase of the Mg content. The microstructure and photoluminescence mechanism have been discussed based on X-ray diffraction patterns, atomic force microscopy images, ultraviolet-visible absorption spectra, photoluminescence spectra and Fourier transform infrared spectra.展开更多
基金the National Natural Science Foundation of China(No.52272009)the Henan Provincial Science and Technology Research Project(No.242102230151)+1 种基金the Henan Provincial University Science and Technology Innovation Team(No.25IRTSTHN009)the Key Scientific Research Projects of Colleges and Universities in Henan Province(Nos.24B560021,25B560020,25B560023)。
文摘This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(200,300,400℃)on their electrochromic properties.The microstructure characterization of WO_(3) films were performed using scanning electron microscope(SEM),X-ray diffraction(XRD),and transmission electron microscope(TEM),and their electrochromic properties were tested by combining an electrochemical workstation with an ultraviolet-visible spectrophotometer.The results showed that the precursor solution concentration directly affected the thickness(290,560,990 nm)and microstructure of WO_(3) films,significantly impacting their electrochromic properties.However,the annealing temperature had a negligible effect.As the precursor solution concentration increased,the optical modulation of WO_(3) films gradually decreased,reaching 51.1%,43.8%,and 35.1%,respectively.The switching time first increased and then stabilized,with coloring times of 7.3,7.7,and 7.7 s,respectively,and bleaching times of 3.8,6.5,and 6.5 s,respectively.The coloration efficiency gradually increased but the increase was relatively small,reaching 41.8,44.4,and 44.8 cm^(2)/C,respectively.Moreover,the cycling stability of WO_(3) films was poor,with the ratios of the final value of optical modulation to the initial value 0.33,0.26,and 0.34,respectively.Additionally,there were bigger differences in the bleached state transmittance,while the colored state transmittance showed smaller variations.However,the former has better cycling stability than the latter.In summary,to obtain better electrochromic properties,the thickness of WO_(3) films should not exceed 290 nm.
基金financially supported by the National Natural Science Foundation of China(No.51373059)the Graphene Powder&Composite Materials Research Center of FujianXiamen Key Laboratory of Polymers and Electronic Materials。
文摘Janus films with asymmetric physical/chemical properties have attracted con siderable attention due to their promising applications in personal thermal management,electronic skin s,sensors,actuators,etc.However,traditional methods for fabricating Janus films conventionally need the assistance of an interface or auxiliary equipment,which are usually complex and time-consuming.Herein,flexible poly(vinyl alcohol)(PVA)/graphene oxide(GO)/h-BN(recorded as PVA/GO/h-BN)Janus films with thermally,optically,and electrically anisotropic properties are fabricated by a simple density deposition self-assem bly method,which just utilizes the density difference between GO and h-BN during water evaporation.Experimental results show that the two sides of the acquired Janus films have obvious asymmetric characteristics.In the original state of the PVA/GO/h-BN Janus films,the thermal conductivity of the GO side(10.06 W·m^(-1)·K^(-1))is generally lower than that of the h-BN side(10.48W·m^(-1)·K^(-1)).But after GO is reduced,the thermal conductivity of the rGO side reaches 12.17 W·m^(-1)·K^(-1),surpassing that of the h-BN side.In addition,the relative reflectance of the h-BN side of Janus film is also significantly higher than that of the rGO side,and the su rface resistance difference between the two sides is about 4 orders of magnitude.The prepared PVA/GO/h-BN Janus films show great application potential in human thermal management,light conversion switches,and electronic skins.This study provides a simple and versatile strategy for fabricating Janus films with multifunctional(such as thermal,optical,and electrical)anisotropies.
基金supported by the National Key Research and Development Program of China(Grant No.2021YFB3501002)the National Natural Science Foundation of China(Grant No.52301059,No.52271009)the Shanghai Post-doctoral Excellence Program(Grant No.2023372).
文摘Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The ignition resistance of these alloys often depends on the protectiveness of the oxide film formed on the surface.This paper elucidates the formation mechanism of oxide film from thermodynamics and kinetics,classifying oxide films based on their layered structure to assess their protective properties.Furthermore,it comprehensively reviews the impact of characteristics on the protective effectiveness such as compactness,continuity,thickness,and mechanical properties.The paper also introduces various characterization methods for the microstructure and properties of oxide film.The primary objective of this paper is to enhance the comprehension of oxide film concerning the ignition resistance of Mg alloys and to furnish references for future advancements and research in Mg alloys with heightened ignition resistance.
基金the National Natural Science Foundation of China(22279097)the Key R&D Program of Hubei Province(2023BAB103)the PhD Scientific Research and Innovation Foundation of The Education Department of Hainan Province Joint Project of Sanya Yazhou Bay Science and Technology City(HSPHDSRF-2024-03-022)。
文摘Because of their low electrical conductivity,sluggish ion diffusion,and poor stability,conventional electrode materials are not able to meet the growing demands of energy storage and portable devices.Graphene assembled films(GAFs)formed from graphene nanosheets have an ultrahigh conductivity,a unique 2D network structure,and exceptional mechanical strength,which give them the potential to solve these problems.However,a systematic understanding of GAFs as an advanced electrode material is lacking.This review focuses on the use of GAFs in electrochemistry,providing a comprehensive analysis of their synthesis methods,surface/structural characteristics,and physical properties,and thus understand their structure-property relationships.Their advantages in batteries,supercapacitors,and electrochemical sensors are systematically evaluated,with an emphasis on their excellent electrical conductivity,ion transport kinetics,and interfacial stability.The existing problems in these devices,such as chemical inertness and mechanical brittleness,are discussed and potential solutions are proposed,including defect engineering and hybrid structures.This review should deepen our mechanistic understanding of the use of GAFs in electrochemical systems and provide actionable strategies for developing stable,high-performance electrode materials.
基金supported by the National Natural Science Foundation of China(No.52074130)Engineering Research Center of Resource Utilization of Carbon-containing Waste with Carbon Neutrality,Ministry of Education,200237 Shanghai,PR China.
文摘To advance the understanding of the corrosion behavior of stainless steel bellows in marine atmospheric environments and enhance the precision of service life predictions,this study employs finite element simulations to investigate the pitting corrosion rates and pit morphologies of bellows peaks and troughs under varying electrolyte film thicknesses.The model incorporates localized electrochemical reactions,oxygen concentration,and homogeneous solution reactions.For improved computational accuracy,the fitted polarization curve data were directly applied as nonlinear boundary conditions on the electrode surface via interpolation functions.Simulation results reveal that the peak regions exhibit faster corrosion rates than the trough regions.With increasing electrolyte film thickness(from 10μm to 500μm),corrosion rates at both peaks and troughs decrease progressively,and after 120 hours of simulation,the maximum corrosion rate at the peaks declines from 0.720 mm/a to 0.130 mm/a,and at the troughs from 0.520 mm/a to 0.120 mm/a,with the disparity in corrosion rates diminishing over time.Furthermore,as corrosion progresses,pits propagate deeper into the substrate,exhibiting both vertical penetration and lateral expansion along the passive film interface,ultimately breaching the substrate.This research offers valuable insights into designing corrosion mitigation strategies for stainless steel bellows in marine environments.
文摘BACKGROUND Dry eye disease(DED)represents a multifactorial condition characterized by ocular discomfort and visual disturbances.The management of DED relies heavily on accurate diagnosis to tailor effective treatments.Diagnostic approaches encompass both subjective and objective assessments.AIM To review the diagnostic methods used in the process of dry eye disease management.METHODS A comprehensive review of diagnostic approaches for dry eye was performed using scientific databases.Studies published within the last four years were considered.Studies were excluded if a full text was absent or the article was not written in English.Articles were assessed for relevancy,and a total of 107 studies were selected.The selection method used a systematic methodology,which guaranteed an exhaustive assessment of the diagnostic techniques reported in current literature.The study adheres to principles for systematic reviews ensuring dependability and accuracy.The studies were assessed for emphasize on both novel traditional and diagnostic methods for dry eye disease management.RESULTS Key objective tests include tear break-up time,which evaluates tear film stability;fluorescein and lissamine green staining,which assess ocular surface damage and inflammation;tear osmolarity measurement,indicative of tear film quality;and tear volume assessment via Schirmer's test,which evaluates tear production.Advanced imaging techniques such as optical coherence tomography and meibography offer detailed anatomical insights into the ocular surface and meibomian glands,aiding in the diagnosis of underlying structural abnormalities.Moreover,emerging technologies such as matrix metalloproteinase-9 testing and inflammatory biomarkers provide additional diagnostic precision,particularly in identifying inflammatory components of DED.CONCLUSION Integrating a combination of subjective and objective diagnostic tools allows clinicians to comprehensively assess the condition,tailor treatment plans,and monitor therapeutic efficacy.Continued advancements in diagnostic technologies promise to enhance our understanding and management of this prevalent ocular condition.
文摘The oral disintegrating film(ODF)offers significant advantages such as superior patient compliance and rapid action onset as a form of solid drug delivery.However,the drug loading efficiency and dosage of the ODF currently available in the market are limited.To enhance the drug loading efficiency,with bacterial cellulose(BC)and hyaluronic acid(HA)as film-forming agents,glycerol(GL)as a plasticizer,and diprophylline(Dilor)as the model drug,a Dilor-ODF was prepared by a solvent casting method for the treatment of acute asthma-related diseases.The BC nano-network structure was utilized to augment the drug loading efficiency of the Dilor-ODF,while HA and GL were used to improve the elongation at break.The disintegration time,drug loading efficiency and drug releasing rate,and tensile properties of the Dilor-ODF were mainly evaluated.The results indicated that the Dilor-ODF exhibited a smooth surface with a uniform thickness and a maximum drug loading efficiency of(51.10±0.08)%.The time for complete disintegration and that for drug release in simulated oral saliva were less than 30 and 90 s,respectively,indicating the effect of rapid release.The tensile strength and elongation at break of the Dilor-ODF were(46.3±2.8)MPa and(1.9±0.2)%,respectively.The thermal decomposition temperature of the Dilor-ODF was higher than 200℃,satisfying subsequent processing demand.
文摘Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.
文摘CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly controlled by the ion-by-ion growth mechanism at the beginning of the film deposition, then the cluster-by-cluster mechanism came to be dominant. The growth rate increased faster with the increasing of temperature until the thickness reached the limitation, then thickness instead become thinner. The scanning electron micro- scope results revealed that the morphology of the CdS film changed from pinholes to rough, inhomogeneous surface with increasing deposition time and deposition temperature. The X- ray diffraction results showed the film structure was a mixture of two phases： hexagonal and cubic, and it was very important to controll deposition time to the film＇s crystal phase. All films in depth of approxilnate 100 nm existed above 65% transmittance, the absorption edge became ＂red-shift＂ with temperature rising. At 60 and 70℃, with 20 min deposited-time, the energy band gap was more than 2.42 eV and decreased with time, while at 80 and 90℃ the energy band gap was less than 2.42 eV and increased little when the time changed from 10min to 15 nfin at 80℃.
基金This work was financially supported by Foundation for Uni-versity Key Teacher by the Ministry of Education, the National Natu-ral Science Foundation of China (No. 50072016) and the Key Re-search Project of the Ministry of Education(No.99087)
文摘Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.
基金This project is financially supported by the National Natural Science Foundation of China (No.s 50272049, 50072016) The Excellent Young Teachers Program of MOE, China (No. (2002)350)
文摘Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.
基金Project(cstc2011jj A50008)supported by the Natural Science Foundation of Chongqing,ChinaProject(14ZB0025)supported by Education Department of Sichuan Province,China
文摘Zn-doped TiO2 (Zn?TiO2) thin films were prepared by the sol?gel method on titanium substrates with heat treatment at different temperatures. The effects of heat treatment temperatures and Zn doping on the structure, photocathodic protection and photoelectrochemical properties of TiO2 thin films were investigated. It is indicated that the photoelectrical performance of the Zn?TiO2 films is enhanced with the addition of Zn element compared with the pure-TiO2 film and the largest decline by 897 mV in the electrode potential is achieved under 300 °C heat treatment. SEM?EDS analyses show that Zn element is unevenly distributed in Zn?TiO2 films; XRD patterns reveal that the grain size of Zn?TiO2 is smaller than that of pure-TiO2; FTIR results indicate that Zn - O bond forms on Zn?TiO2 surface. Ultraviolet visible absorption spectra prove that Zn?TiO2 shifts to visible light region.Mott?Shottky curves show that the flat-band potential of Zn?TiO2 is more negative and charge carrier density is bigger than that ofpure-TiO2, implying that under the synergy of the width of the space-charge layer, carrier density and flat-band potential, Zn?TiO2 with 300 °C heat treatment displays the best photocathodic protection performance.
基金supported by the National Natural Science Foundation of China(Grant No.11304160)the Natural Science Foundation of Jiangsu Provincial Higher Education Institutions,China(Grant No.13KJB140008)the Foundation of Nanjing University of Posts and Telecommunications,China(Grant No.NY213018)
文摘Propagation characteristics of surface acoustic waves（SAWs） in ZnO films/glass substrates are theoretically investigated by the three-dimensional（3D） finite element method. At first, for（11ˉ20） ZnO films/glass substrates, the simulation results confirm that the Rayleigh waves along the [0001] direction and Love waves along the [1ˉ100] direction are successfully excited in the multilayered structures. Next, the crystal orientations of the ZnO films are rotated, and the influences of ZnO films with different crystal orientations on SAW characterizations, including the phase velocity, electromechanical coupling coefficient, and temperature coefficient of frequency, are investigated. The results show that at appropriate h/λ, Rayleigh wave has a maximum k^2 of 2.4% in（90°, 56.5°, 0°） ZnO film/glass substrate structure; Love wave has a maximum k^2 of 3.81% in（56°, 90°, 0°） ZnO film/glass substrate structure. Meantime, for Rayleigh wave and Love wave devices, zero temperature coefficient of frequency（TCF） can be achieved at appropriate ratio of film thickness to SAW wavelength. These results show that SAW devices with higher k^2 or lower TCF can be fabricated by flexibly selecting the crystal orientations of ZnO films on glass substrates.
基金This project is supported by National Natural Science Foundation of China(No.90207003) and Returnee Foundation of Dalian.
文摘Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the density of the PZT film are measured respectively.Bimorph- type bending actuators are fabricated using these films. The model, which is used toanalyze the driving ability of bimorph-type bending actuators by hydrothermal method, is set up. Itcan be seen that the driving ability of bimorph-type bending actuators can be greatly improved byoptimizing the thickness of PZT thin film and substrate from the theoretical analysis results. Themeasured values are expected to agree with the theoretical values calculated by the above model.
基金This work was financially supported by the Natural Science Foundation of Tianjin (No. 33802311)
文摘The effect of different annealing temperatures on the structure, morphology,and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated.Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absoluteethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. Theresults show that ZnO films derived from zinc-citrate have lower crystallization temperature (below400℃), and that the crystal structure is wurtzite. The films, treated over 500℃, consist ofnano-particles and show to be porous at 600℃. The particle size of the film increases with theincrease of the annealing temperature. The largest particle size is 60 nm at 600℃. The opticaltransmittances related to the annealing temperatures become 90% higher in the visible range. Thefilm shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at500℃) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).
基金supported by the National Natural Science Foundation of China(Grant No.50871046)the Foundation of National Key Basic Research and Development Program(No.2010CB631001)the Program for Changjiang Scholars and Innovative Research Team inUniversity
文摘ZnO film with claviform structure was synthesized on quartz substrates through a hydrothermal method at 90℃. The microstructure of the film is composed of clusters of submicrometer rods, which therefore endues the film with good superhydrophobicity. Meanwhile, the film with such tanglesome structure also shows highly crystalline quality testified by a strong ultra-violet （UV） emission and very low deep-level emission observed on the photoluminescence （PL） spectrum as well as high transparence of about 89% transmittance in visible light range.
基金Project supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U1601213)the National Natural Science Foundation of China(Grant Nos.51601005 and 61704006)+1 种基金the Beijing Natural Science Foundation(Grant No.2182032)the Fundamental Research Funds for the Central Universities
文摘Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structures of thermoelectric films,the potential applications of thermoelectric materials are diversified,particularly in microdevices.Well-controlled nanostructures in thermoelectric films are effective to optimize the electrical and thermal transport,which can significantly improve the performance of thermoelectric materials.In this paper,various physical and chemical approaches to fabricate thermoelectric films,including inorganic,organic,and inorganic–organic composites,are summarized,where more attentions are paid on the inorganic thermoelectric films for their excellent thermoelectric responses.Additionally,strategies for enhancing the performance of thermoelectric films are also discussed.
文摘CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were investigated by XRD, SEM, XPS, AFM and UV-VIS. The resultsshowed that the thin films are uniform, compact and good in adhesion to the substrates, and thegrowth of the films is 2.8 nm/cycle. The evolution of structure undergoes from the cubic structureto the hexagonal one with a preferred orientation along the (002) plane after annealing at 673 K. Anamount of C, O and Cl impurities can be reduced by increasing the drying temperature or byannealing in N2 atmosphere. It was found that the band gap of the CdS films shifts to higherwavelength after annealing or increasing film thickness. The electrical resistivity decreases withincreasing annealing temperature and film thickness.
基金This work is financially supported by the Tianjin Science and Technology Committee, China (No. F103004).
文摘RuS_2 thin films were prepared by the cost-effective chemicalmethod―successive ionic layer adsorption and reaction (SILAR). The structural, optical, andelectrical properties were investigated using X-ray diffraction, scanning electron microscopy,optical transmittance, and electrical resistivity methods. The results indicate that the films arehomogeneous and dense; the structure of the as-deposited films is amorphous and they crystallizeafter annealed at 500℃ for 30 min. The band gap of the as-deposited films is found to be 1.85 eV,and the electrical resistivity of them is in the order of 10~5 Ω·cm.
基金supported by the National Natural Science Foundation of China(Nos.10674023 and 60725413)863 Program(No.2006AA03Z313)+1 种基金973 Program(No.2007CB936300)the NSFJ(No.BK2006090)
文摘Well-crystallized MgZnO alloy thin films with hexagonal wurtzite structure were fabricated by sol-gel method. With the band gap increases, the surface roughness and the grain size reduces. It is worth noting that the intensity of the band-edge luminescence of Mg doped films enhances with the increase of the Mg content. The microstructure and photoluminescence mechanism have been discussed based on X-ray diffraction patterns, atomic force microscopy images, ultraviolet-visible absorption spectra, photoluminescence spectra and Fourier transform infrared spectra.
