Polylactic acid(PLA)possesses good mechanical and biodegradability properties which make it a suitable material for polymer composites whereas brittleness and high costs limit its utilization in various applications.T...Polylactic acid(PLA)possesses good mechanical and biodegradability properties which make it a suitable material for polymer composites whereas brittleness and high costs limit its utilization in various applications.The reinforcement of natural fibres with biopolymers has been formed to be an efficient technique to develop composites having the ability to be fully biodegradable.This study concerns with the incorporation of various percentages of untreated and alkali-treated Coir Fibres(CF)and pineapple leaf fibres(PALF)in PLA biocomposites and characterizations of flexural,morphological and dynamic mechanical properties.Flexural properties showed that the treated C1P1 hybrid composites(C1P1A)displayed highest flexural strength(35.81 MPa)and modulus(5.28 GPa)among all hybrid biocomposites.Scanning Electron Microscopy(SEM)revealed a behaviour of fibre-matrix adhesion in untreated treated biocomposites.SEM observation revealed good dispersion of the fillers in PLA.Dynamic mechanical analysis revealed that C1P1A showed highest glass transition temperature(Tg)and storage modulus(E')while untreated C3P7 displayed the least Tg and E'.Overall findings showed that alkali-treated hybrid biocomposites(CF/PALF/PLA)especially C1P1A have improved flexural properties,dynamic and morphological properties over untreated biocomposites.Success of these findings will provide attracting consideration of these hybrid biocomposites for various lightweight uses in a broad selection of industrial applications such as biomedical sectors,automobile,construction,electronics equipment,and hardware tools.展开更多
The growing environmental concerns have led to attention on bio-based composite materials, such as the natural fibres, recycled carbon fibres and bio-based resins. Herein, the bio-based epoxy composites were reinforce...The growing environmental concerns have led to attention on bio-based composite materials, such as the natural fibres, recycled carbon fibres and bio-based resins. Herein, the bio-based epoxy composites were reinforced with ramie fibre (RF) and recycled carbon fibre (rCF) via inter-layer hybridisation. The dynamic mechanical analysis, tensile, flexural and impact properties characterisation were conducted to analyse the mechanical behaviour of the specimens. Also, the morphology of fractured surface after mechanical tests was studied under a scanning electron microscope. When the volume ratio between RF and rCF was varied from 100/0 to 0/100, the flexural and tensile strength of composites was significantly increased, while the impact strength was reduced. Thus the maximum values of flexural strength (182 MPa) and tensile strength (165 MPa) were observed for rCF reinforced composite, whilst impact strength of 24 kJ/m</span><sup><span style="font-family:Verdana;">2</span></sup><span style="font-family:Verdana;"> was found for RF reinforced composite. Furthermore, the values of storage and loss modulus were increased with the rCF incorporation due to a greater degree of restriction with the addition of rCF into the matrix. The hybridisation was able to combine the specific properties of RF and rCF and optimise the mechanical performance of composites. Therefore, the alternative low-cost green composites are prepared which can replace synthetic materials for semi-structural applications.展开更多
The yttrium as a sintering aid was introduced into polycarbosilane（PCS） to prepare yttrium-containing PCS（PYCS）.Two types of yttrium-containing SiC fibres,the SiC（OY） fibres and the SiC（Y） fibres,were fabricat...The yttrium as a sintering aid was introduced into polycarbosilane（PCS） to prepare yttrium-containing PCS（PYCS）.Two types of yttrium-containing SiC fibres,the SiC（OY） fibres and the SiC（Y） fibres,were fabricated with PYCS.The structural evolution and the associated properties on changing from SiC（OY） to SiC（Y） fibres during the sintering process were studied.The chemical composition of the SiC（OY） fibres is SiC1.53O0.22Y0.005 with an amorphous structure.The composition of SiC（Y） fibres is SiC1.23O0.05Y0.005.The fibres are composed of a large number of β-SiC crystallites with a size of 50 nm and a small amount of α-SiC crystalline.The tensile strength and fracture toughness of the SiC（OY） fibres are 2.25 GPa and 2.37 MPa·m1/2,respectively,and 1.61 GPa,1.91 MPa·m1/2,respectively for SiC（Y） fibres.The SiC（Y） fibres have a higher thermal stability than the SiC（OY） fibres.展开更多
The efficiency of activated biochar fibres obtained from Opuntia Ficus lndica regarding me sorpuon oi trlvalent samarium （Sm（Ⅲ）） from aqueous solutions was investigated by batch experiments. The effect of various...The efficiency of activated biochar fibres obtained from Opuntia Ficus lndica regarding me sorpuon oi trlvalent samarium （Sm（Ⅲ）） from aqueous solutions was investigated by batch experiments. The effect of various physicochemical parameters （e.g. pH, initial metal concentration, ionic strength, temperature and contact time） on the Sm（III） adsorption was studied and the surface species were characterized by FTIR spectroscopy prior to and after the lanthanide sorption. The experimental results showed that the acti- vated biochar fibres possessed extraordinary sorption capacity for Sm（Ⅲ） in acidic solutions （qmax=90 g/kg, pH 3.0） and near neutral solutions （qmax=350 g/kg, pH 6.5）, This was attributed to the formation of samarium complexes with the surface carboxylic moieties, available in high density on the lamellar structures of the bio-sorbent.展开更多
The reflected optical caustics method is applied to study dynamic fracture problems in hardened cement paste. First both the unreinforced cement paste and the glass fibres reinforced cement paste specimens were fabric...The reflected optical caustics method is applied to study dynamic fracture problems in hardened cement paste. First both the unreinforced cement paste and the glass fibres reinforced cement paste specimens were fabricated and the reflective coating on the surface of the specimen was prepared. Secondly the crack path and the shadow spot patterns during the crack propagation process for the two specimens were recorded by using a multi-spark high speed camera.Thirdly some dynamic parameters of two cement paste specimens including crack onset time the dynamic stress intensity factor and crack growth velocity were determined and analyzed comparatively.This indicates that the glass fibres can improve the fracture resistance and delay fracture time.These results will play an important role in evaluating the dynamic fracture properties of cement paste.展开更多
The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow...The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.展开更多
Titanium metal matrix composites （TiMMCs） reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre （MCF） metho...Titanium metal matrix composites （TiMMCs） reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre （MCF） method offer optimum properties because of the resulting uniform fibre distribution, minimum fibre damage and fibre volume fraction control. In this paper, the consolidation of Ti-6Al-4V matrix-coated SiC fibres during vacuum hot pressing has been investigated. Experiments were carried out on multi-ply MCFs under vacuum hot pressing （VHP）. In contrast to most of existing studies, the fibre, arrangement has been carefully controlled either in square or hexagonal arrays throughout the consolidated sample. This has enabled the dynamic consolidation behaviour of MCFs to be demonstrated by eliminating the fibre re-arrangement during the VHP process. The microstructural evolution of the matrix coating was reported and the deformation mechanisms involved were discussed.展开更多
It is regretted that the author corrections requested at the proof stage were not made accurately. There are some incorrect typings in two equations which will lead to inaccurate results if readers perform calculation...It is regretted that the author corrections requested at the proof stage were not made accurately. There are some incorrect typings in two equations which will lead to inaccurate results if readers perform calculations directly展开更多
Glass fibres/epoxy resins composites have been performed as ideal materials to make support instruments for high-energy and nuclear physics experiments. The effects of the 3,-ray irradiation on the fatigue strength, t...Glass fibres/epoxy resins composites have been performed as ideal materials to make support instruments for high-energy and nuclear physics experiments. The effects of the 3,-ray irradiation on the fatigue strength, thermal conductivities and thermal stabilities of the glass fibres/epoxy resins composites were investigated. And a two-parameter fatigue life model was established to predict the fatigue life of the composites. Results revealed that the y-ray irradiation could probably result in the degradation of epoxy resins, but hardly damage to the glass fibres. And the γ-ray irradiation treatment could significantly affect the fatigue strength of the composites at a low-cycle fatigue stage, but seldom influence at a high-cycle fatigue stage. Furthermore, the fabricated glass fibres/epoxy resins composites after the γ-ray irradiation still presented excellent fatigue strength, ideal thermal conductivities, remarkable dimensional and thermal stabilities, which can meet the actual requirements of normal operation for supporting instruments under high-energy and nuclear physics experiments.展开更多
This paper theoretically studies the double-pumped fibre-optical parametric amplifiers （FOPAs） in photonic crystal fibres. Two distinct working regimes of FOPAs are researched, which depend on the dispersion at the ...This paper theoretically studies the double-pumped fibre-optical parametric amplifiers （FOPAs） in photonic crystal fibres. Two distinct working regimes of FOPAs are researched, which depend on the dispersion at the central wavelength of the two pumps. Extremely broad tuning range can be obtained when the central pump wavelength is in the normal dispersion regime and is insensitive to the wavelength separation between the two pumps, while the tuning range is narrow in the anomalous dispersion regime and can be significantly enhanced by increasing the wavelength separation. Impacts of higher-order dispersions and temporal walk-off on the gain spectra are also discussed.展开更多
The aim of this study is to investigate the effect of chemical extraction method on the properties of doum palm fibres. The method of extraction which is carried out is a soda treatment. First, an investigation of the...The aim of this study is to investigate the effect of chemical extraction method on the properties of doum palm fibres. The method of extraction which is carried out is a soda treatment. First, an investigation of the extraction processes was undertaken. Secondly, the physical properties (surface morphology, density, linear density and diameter), the mechanical properties (tenacity, strain) and chemical properties (FT-IR spectra) of doum palm fibres were inspected. Finally, a comparison between properties of doum palm fibres and other vegetal ones has been included. Results indicates an influence of soda treatment on properties of Doum palm fibers. In fact, there is an improvement on fibers diameter and linear density while increasing soda concentration, temperature and treatment duration. Moreover, the studied fibers have a low density which does not exceed 1. The fibers tenacity achieved the maximum value of 20.86 cN/Tex when precessing in the following combination (0.75 N, 100°C and 180 mn). In the end, the FTIR spectra reveals a change in structure after this alkali treatment while increasing the cellulose amount exposed on the fiber surface and consequently the number of possible reaction sites (OH groups).展开更多
With the full-vector plane-wave method （FVPWM） and the full-vector beam propagation method （FVBPM）, the dependences of the band-gap and mode characteristics on material index and cladding structure parameter in an...With the full-vector plane-wave method （FVPWM） and the full-vector beam propagation method （FVBPM）, the dependences of the band-gap and mode characteristics on material index and cladding structure parameter in anti- resonance guiding photonic crystal fibres （ARGPCFs） are sufficiently analysed. An ARGPCF operating in the near- infrared wavelength is shown. The influences of the high index cylinders, glass interstitial apexes and silica structure on the characteristics of band-gaps and modes are deeply investigated. The equivalent planar waveguide theory is used for analysing such an ARGPCF filled by the isotropic materials, and the resonance and the anti-resonance characteristics r：~n h~ w~｜] r^r~dlrtpd展开更多
Effects of electrolytes on the oxidation of carbon fibreswere investigated by ion chromatography and cyclic vol-tammogram measurement.The results indicate that theconcentration of nitrate ion decreases with increase o...Effects of electrolytes on the oxidation of carbon fibreswere investigated by ion chromatography and cyclic vol-tammogram measurement.The results indicate that theconcentration of nitrate ion decreases with increase oftreatment time,and the concentration of phosphate ionkeeps a constant in the process of electrochemical oxida-tion.Nitrate ions have more effective electrochemical ox-idation ability than other anions.The mechanism of elec-trochemical oxidation of carbon fibres was suggested.展开更多
The disposal of discarded E-cigarette butts(E-CBs) presents significant environmental challenges due to their detrimental impacts on ecosystems. To find an environmentally sustainable method for managing this waste, t...The disposal of discarded E-cigarette butts(E-CBs) presents significant environmental challenges due to their detrimental impacts on ecosystems. To find an environmentally sustainable method for managing this waste, the potential for recycling E-CBs in asphalt pavements was investigated in this study. By focusing on the two primary components of E-CBs, namely cellulose fibre and polylactic acid(PLA), this research introduced a novel approach for recycling E-CBs in stone mastic asphalt(SMA) as a fibre additive in engineered pellet form. The prepared fibre pellets were directly added to aggregates to produce the SMA mixture. The resulting mixtures underwent a comprehensive evaluation through a series of standardized laboratory tests, including assessments of volumetric properties, indirect tensile strength(ITS), stiffness modulus, moisture susceptibility, and rutting resistance. The results were compared with SMA mixtures containing conventional cellulose fibres. Additionally, to examine the potential influence of PLA, a third mixture was prepared, incorporating both cellulose fibre and PLA. The findings indicate that the SMA using pelletized fibre can satisfy the technical specifications regarding the tests performed in this study, showing higher ITS and rutting resistance compared to the reference mixture. Moreover, the incorporation of PLA plastic reduced air void content and improved tensile strength, stiffness, and rutting resistance. This study highlights the potential for recycling E-CBs in asphalt mixtures, offering technical support for further development of sustainable recycling methods for this waste.展开更多
This review is based on the surface treatment of natural fibres which can be used in technical applications. Natural fibres on their own have some draw backs regarding moisture uptake, quality variations, low thermal ...This review is based on the surface treatment of natural fibres which can be used in technical applications. Natural fibres on their own have some draw backs regarding moisture uptake, quality variations, low thermal stability, and poor wettability. Insufficient adhesion between polymer matrix and fibre leads in time to debonding. Overcoming the weaknesses of these natural fibres gave the motivation for this study where physical and chemical methods of modification were considered. Physical methods such as electric discharge and mercerization were reported as well as the chemical methods such as graft copolymerization and treatment with isocyanates, and the results due to these modifications were discussed. This study reveals that natural fibres are good candidates for reinforcement but they have to be suitably treated to improve their properties if they are to be used in technical applications. The various fibre surface treatments actually improve the interfacial adhesion between the fibre surface and the matrix, thereby giving good mechanical properties to the resulted polymer composites.展开更多
Thatch fibres grow in large quantity in the Adamawa region of Cameroon. During the long dry season, these fibres cause numerous fire incidents, which not only devastate large areas of cash crops, but also contribute t...Thatch fibres grow in large quantity in the Adamawa region of Cameroon. During the long dry season, these fibres cause numerous fire incidents, which not only devastate large areas of cash crops, but also contribute to increase emissions of greenhouse gases into the atmosphere. This article aims to show how fibres could be used with compressed clay bricks to manufacture an insulating material used in building. Four fibre contents 1%, 2%, 3% and 4% made up the sample studied. The asymmetric hot plate methodology was used to determine the thermophysical properties of these composite materials. The volumetric heat capacity and the thermal effusivity of these materials were estimated. These two parametres were used to determine their apparent thermal conductivities. The results obtained show that the thermal conductivity decreases as the volume of fibres in the mixture increases. It is 0.689 W·m-1·K-1 for simple compressed clay bricks and 0.510 W·m-1·K-1 for a dosage at 3% of thatch fibres. In a bit to validate the results of the pilot study of the apparent thermal conductivity, the heat mass capacity of this composite material was achieved through the use of the dehydration method. The relative difference obtained with the results of the volumetric heat capacity carried out with these two methods was good. All results showed that the use of fibres in compressed laterite brick gives a more insulating composite material that respects Civil Engineering Norms.展开更多
This study compares the effect of treated pineapple leaves fibres (T-PALF) with sodium hydroxide solution and untreated fibres (N-PALF) on the compressive and flexural strength of earth bricks stabilized with 3% and 5...This study compares the effect of treated pineapple leaves fibres (T-PALF) with sodium hydroxide solution and untreated fibres (N-PALF) on the compressive and flexural strength of earth bricks stabilized with 3% and 5% cement. The fibre content ranged from 0% to 5% in steps of 1% by weight. The compressive strength tests were made at 7, 14, 21 and 28 days of curing;the flexural strength test were conducted at 28th day only. The results show that the T-PALF had a higher compressive strength when comparing to the N-PALF. The highest compressive strength of the bricks was obtained at 28 days of curing. The compressive strength at 28 days of stabilized brick at 3% and 5% of cement reinforced with T-PALF were 4.01 and 4.81 MPa, respectively, while the one reinforced with N-PALF was 3.19 and 4.63 MPa, respectively. The results further show that the highest flexural strength of both stabilized bricks at 3% and 5% of cement reinforced with T-PALF and N-PALF was obtained with the bricks stabilized with 5% of cement reinforced with T-PALF. This results show that bricks stabilized with 5% cement and reinforced with 3% of treated fibres content are good for construction of load bearing walls. It was observed;a significant improvement of the reinforced blocks under flexure than under compression.展开更多
The objective of this study of modified polypropylene (PP) fibres using nanoadditives (nano-CaCO3 and Cloisite 30B) was to determine the influence of these additives on thermal and mechanical properties, but especiall...The objective of this study of modified polypropylene (PP) fibres using nanoadditives (nano-CaCO3 and Cloisite 30B) was to determine the influence of these additives on thermal and mechanical properties, but especially on the barrier properties of the nanocomposite fibres against UV radiation. The DSC data obtained from measurements of PP/CaCO3 or PP/C30B nanocomposite fibres were used for determination of the constants n and K of the Avrami equation and in the estimation of other thermal properties of the fibres, such as their crystallization half-time t1/2, rate of crystallization t1/2, the necessary time for maximum crystallization tmax and free energy per unit area of surface in the lamella perpen-dicular to the axis of a high-molecular chain se. The nano-CaCO3 or Closite 30B fillers (pre-treated separately in three different solvents: glycerine, acetone and water) did not influence the melting temperatures but caused an increase in PP crystallization temperatures in comparison with the pure PP fibres. The pre-treatments of nanoadditives resulted in increase of n, K, t1/2 values and decrease of t1/2, tmax as well as the values of free surface energies per unit area of the modified PP fibres. There was also observed a decrease in the mechanical properties, however, there was an increase of barrier properties against UV radiation of nanocomposite PP fibres in comparison with neat PP fibres, which was one of the main objectives of the study.展开更多
Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched pris...Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.展开更多
BN coated A1203 fibre-reinforced NiAl-alloy composites were fabricated by hot pressing at 1 200-1 400 ℃, and the interracial microstructure and chemical stability of BN coated Al2O3 fibre-reinforced NiAl-alloy compos...BN coated A1203 fibre-reinforced NiAl-alloy composites were fabricated by hot pressing at 1 200-1 400 ℃, and the interracial microstructure and chemical stability of BN coated Al2O3 fibre-reinforced NiAl-alloy composites were investigated by scanning electron microscopy （SEM） and analytical transmission electron microscopy （TEM）. It was found that the complicated chemical reactions and diffusion processes happened in the interface area between BN-layer and Ni25.8A19.6Ta8.3 during the hot pressing at 1 200-1 400 ℃. A continuous AlN-layer was formed at the interface due to the reaction between NiAl and BN. At the same time, Cr diffused extensively into the BN-layer and reacted with boron to form Cr boride precipitates （CrsB3）. In addition, a few particles of Ta-rich phase were also precipitated in NiAl matrix near the interface.展开更多
基金gratitude to Institute of Tropical Forestry and Forest Products(INTROP),Universiti Putra Malaysia for supporting the funding of research through Grant No:6369108funded by Researchers Supporting Project number(RSP-2021/117),King Saud University,Riyadh,Saudi Arabia.
文摘Polylactic acid(PLA)possesses good mechanical and biodegradability properties which make it a suitable material for polymer composites whereas brittleness and high costs limit its utilization in various applications.The reinforcement of natural fibres with biopolymers has been formed to be an efficient technique to develop composites having the ability to be fully biodegradable.This study concerns with the incorporation of various percentages of untreated and alkali-treated Coir Fibres(CF)and pineapple leaf fibres(PALF)in PLA biocomposites and characterizations of flexural,morphological and dynamic mechanical properties.Flexural properties showed that the treated C1P1 hybrid composites(C1P1A)displayed highest flexural strength(35.81 MPa)and modulus(5.28 GPa)among all hybrid biocomposites.Scanning Electron Microscopy(SEM)revealed a behaviour of fibre-matrix adhesion in untreated treated biocomposites.SEM observation revealed good dispersion of the fillers in PLA.Dynamic mechanical analysis revealed that C1P1A showed highest glass transition temperature(Tg)and storage modulus(E')while untreated C3P7 displayed the least Tg and E'.Overall findings showed that alkali-treated hybrid biocomposites(CF/PALF/PLA)especially C1P1A have improved flexural properties,dynamic and morphological properties over untreated biocomposites.Success of these findings will provide attracting consideration of these hybrid biocomposites for various lightweight uses in a broad selection of industrial applications such as biomedical sectors,automobile,construction,electronics equipment,and hardware tools.
文摘The growing environmental concerns have led to attention on bio-based composite materials, such as the natural fibres, recycled carbon fibres and bio-based resins. Herein, the bio-based epoxy composites were reinforced with ramie fibre (RF) and recycled carbon fibre (rCF) via inter-layer hybridisation. The dynamic mechanical analysis, tensile, flexural and impact properties characterisation were conducted to analyse the mechanical behaviour of the specimens. Also, the morphology of fractured surface after mechanical tests was studied under a scanning electron microscope. When the volume ratio between RF and rCF was varied from 100/0 to 0/100, the flexural and tensile strength of composites was significantly increased, while the impact strength was reduced. Thus the maximum values of flexural strength (182 MPa) and tensile strength (165 MPa) were observed for rCF reinforced composite, whilst impact strength of 24 kJ/m</span><sup><span style="font-family:Verdana;">2</span></sup><span style="font-family:Verdana;"> was found for RF reinforced composite. Furthermore, the values of storage and loss modulus were increased with the rCF incorporation due to a greater degree of restriction with the addition of rCF into the matrix. The hybridisation was able to combine the specific properties of RF and rCF and optimise the mechanical performance of composites. Therefore, the alternative low-cost green composites are prepared which can replace synthetic materials for semi-structural applications.
基金Projects (51175444,50532010) supported by the National Natural Science Foundation of ChinaProject (2011121002) supported by the Fundamental Research Funds for the Central Universities, ChinaProject (2009J1009) supported by Scientific and Technological Innovation Platform of Fujian Province,China
文摘The yttrium as a sintering aid was introduced into polycarbosilane（PCS） to prepare yttrium-containing PCS（PYCS）.Two types of yttrium-containing SiC fibres,the SiC（OY） fibres and the SiC（Y） fibres,were fabricated with PYCS.The structural evolution and the associated properties on changing from SiC（OY） to SiC（Y） fibres during the sintering process were studied.The chemical composition of the SiC（OY） fibres is SiC1.53O0.22Y0.005 with an amorphous structure.The composition of SiC（Y） fibres is SiC1.23O0.05Y0.005.The fibres are composed of a large number of β-SiC crystallites with a size of 50 nm and a small amount of α-SiC crystalline.The tensile strength and fracture toughness of the SiC（OY） fibres are 2.25 GPa and 2.37 MPa·m1/2,respectively,and 1.61 GPa,1.91 MPa·m1/2,respectively for SiC（Y） fibres.The SiC（Y） fibres have a higher thermal stability than the SiC（OY） fibres.
文摘The efficiency of activated biochar fibres obtained from Opuntia Ficus lndica regarding me sorpuon oi trlvalent samarium （Sm（Ⅲ）） from aqueous solutions was investigated by batch experiments. The effect of various physicochemical parameters （e.g. pH, initial metal concentration, ionic strength, temperature and contact time） on the Sm（III） adsorption was studied and the surface species were characterized by FTIR spectroscopy prior to and after the lanthanide sorption. The experimental results showed that the acti- vated biochar fibres possessed extraordinary sorption capacity for Sm（Ⅲ） in acidic solutions （qmax=90 g/kg, pH 3.0） and near neutral solutions （qmax=350 g/kg, pH 6.5）, This was attributed to the formation of samarium complexes with the surface carboxylic moieties, available in high density on the lamellar structures of the bio-sorbent.
基金The Ph.D.Programs Foundation of Ministry of Education of China(No.20120023120020)the National Natural Science Foundation of China(No.51404273)
文摘The reflected optical caustics method is applied to study dynamic fracture problems in hardened cement paste. First both the unreinforced cement paste and the glass fibres reinforced cement paste specimens were fabricated and the reflective coating on the surface of the specimen was prepared. Secondly the crack path and the shadow spot patterns during the crack propagation process for the two specimens were recorded by using a multi-spark high speed camera.Thirdly some dynamic parameters of two cement paste specimens including crack onset time the dynamic stress intensity factor and crack growth velocity were determined and analyzed comparatively.This indicates that the glass fibres can improve the fracture resistance and delay fracture time.These results will play an important role in evaluating the dynamic fracture properties of cement paste.
基金Project supported by the National Natural Science Foundation （Grant No 10372090） and the Doctorate Program of Higher Education of China （Grant No 20030335001）.
文摘The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.
文摘Titanium metal matrix composites （TiMMCs） reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre （MCF） method offer optimum properties because of the resulting uniform fibre distribution, minimum fibre damage and fibre volume fraction control. In this paper, the consolidation of Ti-6Al-4V matrix-coated SiC fibres during vacuum hot pressing has been investigated. Experiments were carried out on multi-ply MCFs under vacuum hot pressing （VHP）. In contrast to most of existing studies, the fibre, arrangement has been carefully controlled either in square or hexagonal arrays throughout the consolidated sample. This has enabled the dynamic consolidation behaviour of MCFs to be demonstrated by eliminating the fibre re-arrangement during the VHP process. The microstructural evolution of the matrix coating was reported and the deformation mechanisms involved were discussed.
文摘It is regretted that the author corrections requested at the proof stage were not made accurately. There are some incorrect typings in two equations which will lead to inaccurate results if readers perform calculations directly
基金financially supported by the National Natural Science Foundation of China (No. 51605025)the Major Program of National Key Research and Development Program of China (2016YFC0802905)+2 种基金the Fundamental Research Funds for the Central Universities (FRF-GF-17-B19)the BEPC great reconstruction projectthe Knowledge Innovation Fund of the Chinese Academy of Sciences, U-603 and U-34 (IHEP)
文摘Glass fibres/epoxy resins composites have been performed as ideal materials to make support instruments for high-energy and nuclear physics experiments. The effects of the 3,-ray irradiation on the fatigue strength, thermal conductivities and thermal stabilities of the glass fibres/epoxy resins composites were investigated. And a two-parameter fatigue life model was established to predict the fatigue life of the composites. Results revealed that the y-ray irradiation could probably result in the degradation of epoxy resins, but hardly damage to the glass fibres. And the γ-ray irradiation treatment could significantly affect the fatigue strength of the composites at a low-cycle fatigue stage, but seldom influence at a high-cycle fatigue stage. Furthermore, the fabricated glass fibres/epoxy resins composites after the γ-ray irradiation still presented excellent fatigue strength, ideal thermal conductivities, remarkable dimensional and thermal stabilities, which can meet the actual requirements of normal operation for supporting instruments under high-energy and nuclear physics experiments.
基金Project partially supported by the Shanghai Committee of Science and Technology, China (Grant Nos 05 SG 02 and 05 JC 14005)the National Natural Science Foundation of China (Grant Nos 60538010 and 10376009)
文摘This paper theoretically studies the double-pumped fibre-optical parametric amplifiers （FOPAs） in photonic crystal fibres. Two distinct working regimes of FOPAs are researched, which depend on the dispersion at the central wavelength of the two pumps. Extremely broad tuning range can be obtained when the central pump wavelength is in the normal dispersion regime and is insensitive to the wavelength separation between the two pumps, while the tuning range is narrow in the anomalous dispersion regime and can be significantly enhanced by increasing the wavelength separation. Impacts of higher-order dispersions and temporal walk-off on the gain spectra are also discussed.
文摘The aim of this study is to investigate the effect of chemical extraction method on the properties of doum palm fibres. The method of extraction which is carried out is a soda treatment. First, an investigation of the extraction processes was undertaken. Secondly, the physical properties (surface morphology, density, linear density and diameter), the mechanical properties (tenacity, strain) and chemical properties (FT-IR spectra) of doum palm fibres were inspected. Finally, a comparison between properties of doum palm fibres and other vegetal ones has been included. Results indicates an influence of soda treatment on properties of Doum palm fibers. In fact, there is an improvement on fibers diameter and linear density while increasing soda concentration, temperature and treatment duration. Moreover, the studied fibers have a low density which does not exceed 1. The fibers tenacity achieved the maximum value of 20.86 cN/Tex when precessing in the following combination (0.75 N, 100°C and 180 mn). In the end, the FTIR spectra reveals a change in structure after this alkali treatment while increasing the cellulose amount exposed on the fiber surface and consequently the number of possible reaction sites (OH groups).
基金partly supported by the National Key Basic Research Special Foundation of China (Grant Nos. 2010CB327605 and 2010CB328300)the National High-Technology Research and Development Program of China (Grant No. 2009AA01Z220)+3 种基金the Key Grant of the Chinese Ministry of Education (Grant No. 109015)the Discipline Co-construction Project of Beijing Municipal Commission of Education,China (Grant No. YB20081001301)the Open Fund of Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications),Chinese Ministry of Educationthe Specialized Research Fund for the Doctoral Program of Beijing University of Posts and Telecommunications (Grant No. CX201023)
文摘With the full-vector plane-wave method （FVPWM） and the full-vector beam propagation method （FVBPM）, the dependences of the band-gap and mode characteristics on material index and cladding structure parameter in anti- resonance guiding photonic crystal fibres （ARGPCFs） are sufficiently analysed. An ARGPCF operating in the near- infrared wavelength is shown. The influences of the high index cylinders, glass interstitial apexes and silica structure on the characteristics of band-gaps and modes are deeply investigated. The equivalent planar waveguide theory is used for analysing such an ARGPCF filled by the isotropic materials, and the resonance and the anti-resonance characteristics r：~n h~ w~｜] r^r~dlrtpd
文摘Effects of electrolytes on the oxidation of carbon fibreswere investigated by ion chromatography and cyclic vol-tammogram measurement.The results indicate that theconcentration of nitrate ion decreases with increase oftreatment time,and the concentration of phosphate ionkeeps a constant in the process of electrochemical oxida-tion.Nitrate ions have more effective electrochemical ox-idation ability than other anions.The mechanism of elec-trochemical oxidation of carbon fibres was suggested.
基金the funding support from China Scholarship Council under the grant CSC No. 202106150028。
文摘The disposal of discarded E-cigarette butts(E-CBs) presents significant environmental challenges due to their detrimental impacts on ecosystems. To find an environmentally sustainable method for managing this waste, the potential for recycling E-CBs in asphalt pavements was investigated in this study. By focusing on the two primary components of E-CBs, namely cellulose fibre and polylactic acid(PLA), this research introduced a novel approach for recycling E-CBs in stone mastic asphalt(SMA) as a fibre additive in engineered pellet form. The prepared fibre pellets were directly added to aggregates to produce the SMA mixture. The resulting mixtures underwent a comprehensive evaluation through a series of standardized laboratory tests, including assessments of volumetric properties, indirect tensile strength(ITS), stiffness modulus, moisture susceptibility, and rutting resistance. The results were compared with SMA mixtures containing conventional cellulose fibres. Additionally, to examine the potential influence of PLA, a third mixture was prepared, incorporating both cellulose fibre and PLA. The findings indicate that the SMA using pelletized fibre can satisfy the technical specifications regarding the tests performed in this study, showing higher ITS and rutting resistance compared to the reference mixture. Moreover, the incorporation of PLA plastic reduced air void content and improved tensile strength, stiffness, and rutting resistance. This study highlights the potential for recycling E-CBs in asphalt mixtures, offering technical support for further development of sustainable recycling methods for this waste.
文摘This review is based on the surface treatment of natural fibres which can be used in technical applications. Natural fibres on their own have some draw backs regarding moisture uptake, quality variations, low thermal stability, and poor wettability. Insufficient adhesion between polymer matrix and fibre leads in time to debonding. Overcoming the weaknesses of these natural fibres gave the motivation for this study where physical and chemical methods of modification were considered. Physical methods such as electric discharge and mercerization were reported as well as the chemical methods such as graft copolymerization and treatment with isocyanates, and the results due to these modifications were discussed. This study reveals that natural fibres are good candidates for reinforcement but they have to be suitably treated to improve their properties if they are to be used in technical applications. The various fibre surface treatments actually improve the interfacial adhesion between the fibre surface and the matrix, thereby giving good mechanical properties to the resulted polymer composites.
文摘Thatch fibres grow in large quantity in the Adamawa region of Cameroon. During the long dry season, these fibres cause numerous fire incidents, which not only devastate large areas of cash crops, but also contribute to increase emissions of greenhouse gases into the atmosphere. This article aims to show how fibres could be used with compressed clay bricks to manufacture an insulating material used in building. Four fibre contents 1%, 2%, 3% and 4% made up the sample studied. The asymmetric hot plate methodology was used to determine the thermophysical properties of these composite materials. The volumetric heat capacity and the thermal effusivity of these materials were estimated. These two parametres were used to determine their apparent thermal conductivities. The results obtained show that the thermal conductivity decreases as the volume of fibres in the mixture increases. It is 0.689 W·m-1·K-1 for simple compressed clay bricks and 0.510 W·m-1·K-1 for a dosage at 3% of thatch fibres. In a bit to validate the results of the pilot study of the apparent thermal conductivity, the heat mass capacity of this composite material was achieved through the use of the dehydration method. The relative difference obtained with the results of the volumetric heat capacity carried out with these two methods was good. All results showed that the use of fibres in compressed laterite brick gives a more insulating composite material that respects Civil Engineering Norms.
文摘This study compares the effect of treated pineapple leaves fibres (T-PALF) with sodium hydroxide solution and untreated fibres (N-PALF) on the compressive and flexural strength of earth bricks stabilized with 3% and 5% cement. The fibre content ranged from 0% to 5% in steps of 1% by weight. The compressive strength tests were made at 7, 14, 21 and 28 days of curing;the flexural strength test were conducted at 28th day only. The results show that the T-PALF had a higher compressive strength when comparing to the N-PALF. The highest compressive strength of the bricks was obtained at 28 days of curing. The compressive strength at 28 days of stabilized brick at 3% and 5% of cement reinforced with T-PALF were 4.01 and 4.81 MPa, respectively, while the one reinforced with N-PALF was 3.19 and 4.63 MPa, respectively. The results further show that the highest flexural strength of both stabilized bricks at 3% and 5% of cement reinforced with T-PALF and N-PALF was obtained with the bricks stabilized with 5% of cement reinforced with T-PALF. This results show that bricks stabilized with 5% cement and reinforced with 3% of treated fibres content are good for construction of load bearing walls. It was observed;a significant improvement of the reinforced blocks under flexure than under compression.
文摘The objective of this study of modified polypropylene (PP) fibres using nanoadditives (nano-CaCO3 and Cloisite 30B) was to determine the influence of these additives on thermal and mechanical properties, but especially on the barrier properties of the nanocomposite fibres against UV radiation. The DSC data obtained from measurements of PP/CaCO3 or PP/C30B nanocomposite fibres were used for determination of the constants n and K of the Avrami equation and in the estimation of other thermal properties of the fibres, such as their crystallization half-time t1/2, rate of crystallization t1/2, the necessary time for maximum crystallization tmax and free energy per unit area of surface in the lamella perpen-dicular to the axis of a high-molecular chain se. The nano-CaCO3 or Closite 30B fillers (pre-treated separately in three different solvents: glycerine, acetone and water) did not influence the melting temperatures but caused an increase in PP crystallization temperatures in comparison with the pure PP fibres. The pre-treatments of nanoadditives resulted in increase of n, K, t1/2 values and decrease of t1/2, tmax as well as the values of free surface energies per unit area of the modified PP fibres. There was also observed a decrease in the mechanical properties, however, there was an increase of barrier properties against UV radiation of nanocomposite PP fibres in comparison with neat PP fibres, which was one of the main objectives of the study.
文摘Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.
基金Project (10972190) supported by the National Natural Science Foundation of China Projects (09A089, 08C207) supported by the Scientific Research Fund of Hunan Provincial Education Department,ChinaProject (2010FJ3132) supported by the Planned Science and Technology Project of Hunan Province,China
文摘BN coated A1203 fibre-reinforced NiAl-alloy composites were fabricated by hot pressing at 1 200-1 400 ℃, and the interracial microstructure and chemical stability of BN coated Al2O3 fibre-reinforced NiAl-alloy composites were investigated by scanning electron microscopy （SEM） and analytical transmission electron microscopy （TEM）. It was found that the complicated chemical reactions and diffusion processes happened in the interface area between BN-layer and Ni25.8A19.6Ta8.3 during the hot pressing at 1 200-1 400 ℃. A continuous AlN-layer was formed at the interface due to the reaction between NiAl and BN. At the same time, Cr diffused extensively into the BN-layer and reacted with boron to form Cr boride precipitates （CrsB3）. In addition, a few particles of Ta-rich phase were also precipitated in NiAl matrix near the interface.
