The effects of deep cryogenic-cycling treatment(DCT)on the mechanical properties,soft magnetic properties,and atomic scale structure of the Fe_(73.5)Si_(13.5)B_(9)Nb_(3)Cu_(1)amorphous nanocrystalline alloy were inves...The effects of deep cryogenic-cycling treatment(DCT)on the mechanical properties,soft magnetic properties,and atomic scale structure of the Fe_(73.5)Si_(13.5)B_(9)Nb_(3)Cu_(1)amorphous nanocrystalline alloy were investigated.The DCT samples were obtained by subjecting the as-annealed samples to a thermal cycling process between the temperature of the supercooled liquid zone and the temperature of liquid nitrogen.Through flat plate bending testing,hardness measurements,and nanoindentation experiment,it is found that the bending toughness of the DCT samples is improved and the soft magnetic properties are also slightly enhanced.These are attributed to the rejuvenation behavior of the DCT samples,which demonstrate a higher enthalpy of relaxation.Therefore,DCT is an effective method to enhance the bending toughness of Fe-based amorphous nanocrystalline alloys without degrading the soft magnetic properties.展开更多
In general,the rapid growth of α-Fe clusters is a challenge in high Fe-content Fe-based amorphous alloys,negatively affecting their physical properties.Herein,we introduce an efficient and rapid post-treatment techni...In general,the rapid growth of α-Fe clusters is a challenge in high Fe-content Fe-based amorphous alloys,negatively affecting their physical properties.Herein,we introduce an efficient and rapid post-treatment technique known as ultrasonic vibration rapid processing(UVRP),which enables the formation of high-density strong magnetic α-Fe clusters,thereby enhancing the soft magnetic properties of Fe_(78)Si(13)B_(9) amorphous alloy ribbon.展开更多
Spark erosion is a convenient,flexible,and low-cost method to quickly produce fine powders of metals,alloys,and semiconductors in size ranging from nearly a hundred micrometers to submicrometer by repetitive spark dis...Spark erosion is a convenient,flexible,and low-cost method to quickly produce fine powders of metals,alloys,and semiconductors in size ranging from nearly a hundred micrometers to submicrometer by repetitive spark discharges.Due to the complexity of the powder-forming journey,normally accompanied by high temperature,high pressure,decomposition,diffusion and rapid quenching caused by discharge plasma,the mechanisms of powder formation and possible contaminant infiltration are still controversial,posing a significant challenge to control particle size and chemical composition of the powder produced by this method.In this study,Fe-based amorphous powders in different particle-size distributions with high sphericity were fabricated by spark erosion under different discharge-energy conditions.The max-imum particle size of the resultant powders can be correlated with discharge parameters,crater depth,and crater radius,respectively.A multi-ring-breakup model is proposed to reveal the particle-size distribution of the powder formed from the electrode melt under a single-pulse discharge.Furthermore,a dielectric-element infiltration model is provided to quantitatively evaluate the infiltration mass ratio of the contaminant elements,stemming from the decomposed products of dielectric liquid,in the resultant powder with different particle sizes.The models verified through the experimental data are significant for the development of high-performance fine Fe-based amorphous powder with controlled particle size and chemical composition.展开更多
Laser 3D printing,also known as laser additive manufacturing(LAM),is favored for its ability to form bulk metallic glass(BMG)and its composite materials(BMGcs)with freeform geometries.In this work,two different kinds ...Laser 3D printing,also known as laser additive manufacturing(LAM),is favored for its ability to form bulk metallic glass(BMG)and its composite materials(BMGcs)with freeform geometries.In this work,two different kinds of Fe_(41)Co_(7)Cr_(15)Mo_(14)C_(15)B_(6)Y_(2)amorphous coatings(A and B)were prepared by using LAM technology under air-and water-cooled conditions,respectively;meanwhile,to reduce the cracks generated due to the residual thermal stresses,coating C obtained by air-sweep annealing of B with a low energy-density laser.The morphology and amorphous content and microstructure of the coatings were investigated,the results show many cracks in coating B deposited under water-cooled conditions,and its microstructure shows an amorphous-crystal-nanocrystalline mixed structure.Cracking was suppressed in coating C,obtained by air-sweep annealing based on coating B,but the amorphous content was reduced from 32.6 to 13.4%.And the hardness and corrosion resistance of the coating will increase with the increase in the amorphous content.Finally,the internal friction behavior of a BMGcs was prepared on the basis of the process of sample C is compared with that of as-cast amorphous alloys.The results show that the low temperature internal friction behavior of BMGcs is affected by the defects produced during printing,and the high temperature internal friction behavior is affected by the precipitated hard phase.展开更多
The inverse relationship between the saturation magnetic flux density(Bs)and coercivity(Hc)of Febased amorphous alloys is a very active research topic that has been extensively debated.In this work,we conducted a deta...The inverse relationship between the saturation magnetic flux density(Bs)and coercivity(Hc)of Febased amorphous alloys is a very active research topic that has been extensively debated.In this work,we conducted a detailed investigation on the magnetic softness of Fe_(83.2-x)Co_(x)B_(10)C_(6)Cu_(0.8)(x=0 and 6 at.%)amorphous alloys based on analysis of the surface morphology,microstructure,magnetic anisotropy,and magnetic domain structure.Enhanced magnetic softness-magnetization synergy was realized in the present alloys by magnetic field annealing(MFA)during the de-stressing process.A dramatic 84%reduction of Hc to 2.2 A/m was achieved for the Co-doped alloy under MFA,exhibiting excellent magnetic performance with a superb Bs of 1.86 T.The consistency between the experimental results and theoretical analysis revealed that the MFA process can mitigate the trade-off between stress-induced anisotropy and induced uniaxial anisotropy owing to the homogenized structure formed by field annealing.Thus,the process favored a low Hc due to the significant continuous decline in the total magnetic anisotropy,which coincided well with the results of Magneto-optical Kerr microscopy.The study elucidates a mechanism for tuning Hc in Co-doped alloy systems and affords a possible pathway for softening amorphous alloys with high Bs.展开更多
Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses....Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses.Using the realizable k-εmodel and discrete phase model theory,the flow dynamics of the gas phase and gas-melt two-phase flow felds in the close-wake condition were investigated to establish the correlation between high gas pressure and powder particle characteristics.The locations of the recirculation zones and the shapes of Mach disks were analyzed in detail for the type of discrete-jet closed-coupled gas atomization nozzle.In the gas-phase flow feld,the vortexes,closed to the Mach disk,are found to be a new deceleration method.In the two-phase flow feld,the shape of Mach disk changes from“S”-shape to“Z”-shape under the impact of the droplet flow.As predicted by the wave model,with the elevation of gas pressure,the size of the particle is found to gradually decrease and its distribution becomes more concentrated.Simulation results were compliant with the Fe-based amorphous alloy powder preparation tests.This study deepens the understanding of the gas pressure impacting particle features via gas atomization,and contributes to technological applications.展开更多
In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) ...In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) spraying.The microstructure of the composite coatings was systematically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The main structure of composite coatings remained amorphous while 31 6L stainless steel splats were distributed homogeneously in the amorphous matrix and well connected with surrounding amorphous phase.Bonding strength of coatings to the substrate was determined by 'pull-off' tensile tests.The results revealed that the31 6L stainless steel phase effectively improved the bonding strength of amorphous coatings,which is mainly contributed by the strong metallurgical bonding between stainless steel and amorphous splats.The addition of31 6L stainless steel also enhanced the ductility and fracture resistance of the coatings due to the ductile stainless steel phases,which can arrest crack propagation and increase energy dissipation.展开更多
Designing low melting point and low basicity refining slag suitable for Fe-based amorphous alloys and understanding the inclusions’formation,removal,influencing mechanisms are quite vital in the fields of metallurgy ...Designing low melting point and low basicity refining slag suitable for Fe-based amorphous alloys and understanding the inclusions’formation,removal,influencing mechanisms are quite vital in the fields of metallurgy and materials.In this study,a novel 13%SiO_(2)-32%CaO-30%Al_(2)O_(3)-25%B_(2)O_(3)(wt.%)refining slag was designed after careful calculations of the liquid phase region,slag-metal equilibrium,surface tension,viscosity,deoxidation capability and sulfur distribution ratio.After refining with our designed slag,the content of impurities and the number density of inclusions in a representative Fe_(83)Si_(2)B_(15)(at.%)amor-phous alloy were significantly reduced.Moreover,the glass-forming ability(GFA)of the alloy was also enhanced,enabling the preparation of amorphous ribbons with a lower cooling rate.Based on the impu-rities in Fe-based amorphous alloys as well as the calculated oxide and sulfide free energy diagrams,CaO,SiO_(2),Al_(2)O_(3) oxides and CaS,TiS,MnS sulfides will form in the master alloy.The high melting point in-clusions in the melt are generally removed via a floatation-separation-absorption process and the Mn,Ti,S impurities are removed via slag-metal interface reactions during refining.As for the detrimental effect of inclusions on glass formation,the small lattice disregistry between Ti,Mn-containing inclusions and primaryα-Fe gains reveal that these inclusions are effective in promoting the heterogeneous nucleation,and therefore greatly deteriorate the GFA.These findings are important and provide an ideal solution to purifying the Fe-based amorphous alloys by refining and enhancing the GFA for industrial production.展开更多
The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance ...The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance of T91 stainless steel in liquid lead-bismuth eutectic(LBE).The corrosion behavior of the T91 steel and coating exposed to oxygen-saturated LBE at 400℃ for 500 h was investigated.Results showed that the T91 substrate was severely corroded and covered by a homogeneously distributed dual-layer oxide on the interface contacted to LBE,consisting of an outer magnetite layer and an inner Fe-Cr spinel layer.Meanwhile,the amorphous coating with a high glass transition temperature(Tg=550℃)and crystallization temperature(T_(x)=600℃)exhibited dramatically enhanced thermal stability and corrosion resistance.No visible LBE penetration was observed,although small amounts of Fe_(3)O_(4),Cr_(2)O_(3),and PbO were found on the coating surface.In addition,the amorphicity and interface bonding of the coating layer remained unchanged after the LBE corrosion.The Fe-based amorphous coating can act as a stable barrier layer in liquid LBE and have great application potential for long-term service in LBE-cooled fast reactors.展开更多
The Fe-based amorphous metallic matrix coating （Fe-AMMC） was fabricated with the powder mixtures of Fe-based metallic glass synthesized with industrial raw materials, NiCr alloy and WC particle by high velocity oxy-...The Fe-based amorphous metallic matrix coating （Fe-AMMC） was fabricated with the powder mixtures of Fe-based metallic glass synthesized with industrial raw materials, NiCr alloy and WC particle by high velocity oxy-fuel （HVOF） spraying. The corrosion resistance of Fe-AMMC was investigated by potentiodynamic polarization tests in 1 mol/L HCl, NaCl, H2SO4 and NaOH solutions, respectively. The surface morphologies corroded were observed by SEM. The results indicate that Fe-AMMC exhibits excellent corrosion resistance, higher corrosion resistance than 304L stainless steel in the chloride solutions. The low corrosion current density and passive current density of Fe-AMMC with a wide spontaneous passivation region are about 132.0μA/cm2 and 9.0 mA/cm2 in HCl solution, and about 2.5 μA/cm2 and 2.3 mA/cm2 in NaCl solution. The excellent corrosion resistance demonstrates that Fe-based amorphous metallic matrix powder is a viable engineering material in practical anti-corrosion and anti-wear coating applications.展开更多
Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the...Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.展开更多
Amorphous alloys without crystalline defects(dislocation,crystal boundary)are ideal hydrophobic coating materials due to their low surface energy.This work used a synergistic method of detonation spraying and surface ...Amorphous alloys without crystalline defects(dislocation,crystal boundary)are ideal hydrophobic coating materials due to their low surface energy.This work used a synergistic method of detonation spraying and surface modification to obtain the superhydrophobic Febased amorphous coatings with high hardness and dense structure on the Q 235 substrate.The results showed that the water contact angles(WCA)of the superhydrophobic coating was 160°±3.6°,and water droplets could bounce off the superhydrophobic coating surface,illustrating the excellent self-cleaning performance of coating.Notably,the corrosion current density(i_(corr))of the superhydrophobic coating further decreased by 2 orders of magnitude down to8.008×10^(-8)A·cm^(-2)compared to the as-deposited coating with 5.473×10^(-6)A·cm^(-2);the corrosion potential(E_(corr))of the superhydrophobic coating shifted by 34 mV to the positive side compared with that of the as-deposited coating(-310 mV).Likewise,the impedance modulus|Z|values of the superhydrophobic coating increased by nearly2 orders of magnitude up to 1×10^(5.6)compared to the asdeposited coating with 1×10^(3.8).Even through lasting immersion in NaCl for 10 days,|Z|values of the superhydrophobic coating were still much higher than those of the as-deposited coating.The superhydrophobic Fe-based amorphous coatings could respond to their applications under extreme conditions due to their excellent hydrophobicity and self-cleaning properties,illustrating their promising future in aerospace,automotive,and machinery industries.展开更多
Hot corrosion behaviors of the 921A alloy and Fe-based amorphous coating induced by KCl-10% ZnCl_(2) and KCl-55% ZnCl_(2) salts at 450℃ in air for 40 h were investigated.Results show that the 921A alloy suffers more ...Hot corrosion behaviors of the 921A alloy and Fe-based amorphous coating induced by KCl-10% ZnCl_(2) and KCl-55% ZnCl_(2) salts at 450℃ in air for 40 h were investigated.Results show that the 921A alloy suffers more serious corrosion damage than the coating and KCl-55% ZnCl_(2) salts are more corrosive than KCl-10% ZnCl_(2) salts.In the two salts,an Fe_(2)O_(3) layer is formed on the 921A alloy surface,while an outer Fe-rich oxide layer and an inner Cr-rich oxide layer are formed on the surface of the coating.Moreover,a certain amount of metal chloride can be found at the oxide/alloy(coating)interface,which can be explained by "active oxidation".However,the corrosion resistance of the Fe-based amorphous coating did not achieve the desired results,probably because the intersplats in the coating serve as corrosion diffusing channels,which facilitate the corrosion damage rate.Nevertheless,the coating is still in amorphous state after hot corrosion exposure.展开更多
A new Fe-based amorphous–crystalline composite without non-metallic elements, Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5), was prepared by melt-spinning. The formation ability and structure information were investigated by X-r...A new Fe-based amorphous–crystalline composite without non-metallic elements, Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5), was prepared by melt-spinning. The formation ability and structure information were investigated by X-ray diffractometer(XRD), energy-dispersive spectrometer(EDS) and scanning electron microscope(SEM). The mechanical properties of the amorphous–crystalline composite were investigated by nanoindentation. A molecular dynamics simulation study was performed to simulate the formation of Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5) amorphous alloy. The mechanical properties were obtained by compression simulations simultaneously. The results indicate that the Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5) ribbon is an amorphous–crystalline composite structure with good ductility, and the hardness of the amorphous–crystalline composite is about 75%higher than that of master ingot. The simulation mechanical properties are in good agreement with the results of nanoindentation at the nanoscale.展开更多
Separated preparation of prealloys and amorphous alloys results in severe solidification-remelting and beneficial element removal-readdition contradictions,which markedly increase energy consumption and emissions.This...Separated preparation of prealloys and amorphous alloys results in severe solidification-remelting and beneficial element removal-readdition contradictions,which markedly increase energy consumption and emissions.This study offered a novel strategy for the direct production of FePC amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore(HPIO)and apatite.First,the thermodynamic conditions and equilibrium states of the carbothermal reduction reactions in HPIO were calculated,and the element content in reduced alloys was theoretically determined.The phase and structural evolutions,as well as element migration and enrichment behaviors during the smelting reduction of HPIO and Ca_(3)(PO_(4))_(2),were then experimentally verified.The addition of Ca_(3)(PO_(4))_(2)in HPIO contributes to the enrichment of the P element in reduced alloys and the subsequent development of Fe_(3)P and Fe_(2)P phases.The content of P and C elements in the range of 1.52 wt% -14.63 wt% and 0.62 wt% -2.47 wt%,respectively,can be well tailored by adding 0-50 g Ca_(3)(PO_(4))_(2)and controlling the C/O mole ratio of 0.8-1.1,which is highly consistent with the calculated results.These FePC alloys were then successfully formed into amorphous ribbons and rods.The energy consumption of the proposed strategy was estimated to be 2.00×10^(8) kJ/t,which is reduced by 30% when compared with the conventional production process.These results are critical for the comprehensive utilization of mineral resources and pave the way for the clean production of Fe-based amorphous soft magnetic alloys.展开更多
The addition of early transition metals(ETMs)into Fe-based amorphous alloys is practically found to be effective in reducing theα-Fe grain size in crystallization process.In this paper,by using ab initio molecular dy...The addition of early transition metals(ETMs)into Fe-based amorphous alloys is practically found to be effective in reducing theα-Fe grain size in crystallization process.In this paper,by using ab initio molecular dynamics simulations,the mechanism of the effect of two typical ETMs(Nb and W)on nano-crystallization is studied.It is found that the diffusion ability in amorphous alloy is mainly determined by the bonding energy of the atom rather than the size or weight of the atom.The alloying of B dramatically reduces the diffusion ability of the ETM atoms,which prevents the supply of Fe near the grain surface and consequently suppresses the growth ofα-Fe grains.Moreover,the difference in grain refining effectiveness between Nb and W could be attributed to the larger bonding energy between Nb and B than that between W and B.展开更多
The effects of kerosene flow rate on the microstructure and wearing properties were investigated for Fe-based amorphous coatings sprayed by High Velocity Oxygen Fuel (HVOF).The microstructures and wearing properties o...The effects of kerosene flow rate on the microstructure and wearing properties were investigated for Fe-based amorphous coatings sprayed by High Velocity Oxygen Fuel (HVOF).The microstructures and wearing properties of the Fe-based amorphous coatings were analyzed with scanning electron microscope (SEM),X-ray diffraction analyzer (XRD),and ball-on-disc tribometer (CFT-1),respectively.The experimental results show that the well interfacial bonding can be observed between the amorphous coating layer and the substrate,and the porosity in amorphous coating layer is less to 1%.Only some crystalline a-Fe and FeO phases can be detected by XRD in the amorphous coatings,while the amorphous content is up to 99.4%.The wearing coefficient is near to 0.15,which is superior to SUS316 of 0.28.As the increasing of wearing loads,the failure mode is changed from oxidation wear to the composite of oxidation and abrasive wear.展开更多
Substituting boron for carbon can improve the corrosion behavior of Fe-based amorphous significantly especially in acid solution with saturated H_2S. XPS analysis proves that boron enriches in the surface layer of amo...Substituting boron for carbon can improve the corrosion behavior of Fe-based amorphous significantly especially in acid solution with saturated H_2S. XPS analysis proves that boron enriches in the surface layer of amorphous and reacts with hydrogen to form B_(10)H_(14) . It efficiently prevents the intrusion of hydrogen to the sample, thus the destructive effect of hydrogen can be decreased greatly.展开更多
A ferromagnetic amorphous Fe73Al4Ge2Nb1P10C6B4 alloy with high glass-forming ability was synthesized by melt spinning. The supercooled liquid region before crystallization reaches about 65.7 K. The crystallized struct...A ferromagnetic amorphous Fe73Al4Ge2Nb1P10C6B4 alloy with high glass-forming ability was synthesized by melt spinning. The supercooled liquid region before crystallization reaches about 65.7 K. The crystallized structure consists of alpha -Fe, Fe3B, FeB, Fe3P and Fe3C phases. The Fe-based amorphous alloy exhibits good magnetic properties with a high saturation magnetization and a low saturated magnetostriction. The crystallization leads to an obvious decrease in the soft magnetic properties.展开更多
Amorphous metallic coatings with a composition of Fe48Cr15Mo14C15B6Y2 were prepared by detonation gun spraying process. Microstructural studies show that the coatings present a densely layered structure typical of the...Amorphous metallic coatings with a composition of Fe48Cr15Mo14C15B6Y2 were prepared by detonation gun spraying process. Microstructural studies show that the coatings present a densely layered structure typical of thermally sprayed deposits with the porosity below 2%. Both crystallization and oxidation occurred obviously during spraying process, so that the amorphous fraction of the coatings decreased to 54% compared with fully amorphous alloy ribbons of the same component. Corrosion behavior of the amorphous coatings was investigated by electrochemical measurement. The results show that the coatings exhibit extremely wide passive region and low passive current density in 3.5% NaCl (mass fraction) and 1 mol/L HCl solutions, which illustrates excellent ability to resist localized corrosion.展开更多
基金supported by Liaoning Joint Fund of NSFC(No.U1908219)。
文摘The effects of deep cryogenic-cycling treatment(DCT)on the mechanical properties,soft magnetic properties,and atomic scale structure of the Fe_(73.5)Si_(13.5)B_(9)Nb_(3)Cu_(1)amorphous nanocrystalline alloy were investigated.The DCT samples were obtained by subjecting the as-annealed samples to a thermal cycling process between the temperature of the supercooled liquid zone and the temperature of liquid nitrogen.Through flat plate bending testing,hardness measurements,and nanoindentation experiment,it is found that the bending toughness of the DCT samples is improved and the soft magnetic properties are also slightly enhanced.These are attributed to the rejuvenation behavior of the DCT samples,which demonstrate a higher enthalpy of relaxation.Therefore,DCT is an effective method to enhance the bending toughness of Fe-based amorphous nanocrystalline alloys without degrading the soft magnetic properties.
基金supported by the Major Science and Technology Project of Zhongshan City(No.2022AJ004)the Key Basic and Applied Research Program of Guangdong Province(Nos.2019B030302010 and 2022B1515120082)Guangdong Science and Technology Innovation Project(No.2021TX06C111).
文摘In general,the rapid growth of α-Fe clusters is a challenge in high Fe-content Fe-based amorphous alloys,negatively affecting their physical properties.Herein,we introduce an efficient and rapid post-treatment technique known as ultrasonic vibration rapid processing(UVRP),which enables the formation of high-density strong magnetic α-Fe clusters,thereby enhancing the soft magnetic properties of Fe_(78)Si(13)B_(9) amorphous alloy ribbon.
基金supported by the National Natural Science Foundation of China(Grant Nos.52171150 and 51971006)the National Key Research and Development Program of China(Grant No.2018YFA0703601)the Fundamental Research Funds for the Central Universities(Grant No.YWF-22-L-513).
文摘Spark erosion is a convenient,flexible,and low-cost method to quickly produce fine powders of metals,alloys,and semiconductors in size ranging from nearly a hundred micrometers to submicrometer by repetitive spark discharges.Due to the complexity of the powder-forming journey,normally accompanied by high temperature,high pressure,decomposition,diffusion and rapid quenching caused by discharge plasma,the mechanisms of powder formation and possible contaminant infiltration are still controversial,posing a significant challenge to control particle size and chemical composition of the powder produced by this method.In this study,Fe-based amorphous powders in different particle-size distributions with high sphericity were fabricated by spark erosion under different discharge-energy conditions.The max-imum particle size of the resultant powders can be correlated with discharge parameters,crater depth,and crater radius,respectively.A multi-ring-breakup model is proposed to reveal the particle-size distribution of the powder formed from the electrode melt under a single-pulse discharge.Furthermore,a dielectric-element infiltration model is provided to quantitatively evaluate the infiltration mass ratio of the contaminant elements,stemming from the decomposed products of dielectric liquid,in the resultant powder with different particle sizes.The models verified through the experimental data are significant for the development of high-performance fine Fe-based amorphous powder with controlled particle size and chemical composition.
基金This work was supported by the National Natural Science Foundation of China(No.52161028)the Major Discipline Academic and Technical Leaders Training Program of Jiangxi Province(No.20213BCJ22017).
文摘Laser 3D printing,also known as laser additive manufacturing(LAM),is favored for its ability to form bulk metallic glass(BMG)and its composite materials(BMGcs)with freeform geometries.In this work,two different kinds of Fe_(41)Co_(7)Cr_(15)Mo_(14)C_(15)B_(6)Y_(2)amorphous coatings(A and B)were prepared by using LAM technology under air-and water-cooled conditions,respectively;meanwhile,to reduce the cracks generated due to the residual thermal stresses,coating C obtained by air-sweep annealing of B with a low energy-density laser.The morphology and amorphous content and microstructure of the coatings were investigated,the results show many cracks in coating B deposited under water-cooled conditions,and its microstructure shows an amorphous-crystal-nanocrystalline mixed structure.Cracking was suppressed in coating C,obtained by air-sweep annealing based on coating B,but the amorphous content was reduced from 32.6 to 13.4%.And the hardness and corrosion resistance of the coating will increase with the increase in the amorphous content.Finally,the internal friction behavior of a BMGcs was prepared on the basis of the process of sample C is compared with that of as-cast amorphous alloys.The results show that the low temperature internal friction behavior of BMGcs is affected by the defects produced during printing,and the high temperature internal friction behavior is affected by the precipitated hard phase.
基金supported by the Anhui Provincial Natural Science Foundation(No.2208085QE121)the Key Research&Development plan of Anhui Province(No.2022a05020016)+2 种基金the University Natural Science Research Project of Anhui Province(No.2023AH051084)the National Natural Science Foundation of China(No.52071078)the“Zhishan”Scholars Programs of Southeast University(No.2242021R41158).
文摘The inverse relationship between the saturation magnetic flux density(Bs)and coercivity(Hc)of Febased amorphous alloys is a very active research topic that has been extensively debated.In this work,we conducted a detailed investigation on the magnetic softness of Fe_(83.2-x)Co_(x)B_(10)C_(6)Cu_(0.8)(x=0 and 6 at.%)amorphous alloys based on analysis of the surface morphology,microstructure,magnetic anisotropy,and magnetic domain structure.Enhanced magnetic softness-magnetization synergy was realized in the present alloys by magnetic field annealing(MFA)during the de-stressing process.A dramatic 84%reduction of Hc to 2.2 A/m was achieved for the Co-doped alloy under MFA,exhibiting excellent magnetic performance with a superb Bs of 1.86 T.The consistency between the experimental results and theoretical analysis revealed that the MFA process can mitigate the trade-off between stress-induced anisotropy and induced uniaxial anisotropy owing to the homogenized structure formed by field annealing.Thus,the process favored a low Hc due to the significant continuous decline in the total magnetic anisotropy,which coincided well with the results of Magneto-optical Kerr microscopy.The study elucidates a mechanism for tuning Hc in Co-doped alloy systems and affords a possible pathway for softening amorphous alloys with high Bs.
基金supported by the National Key Research and Development Program of China(No.2016YFB1100204)the Key Research&Development Plan of Jiangxi Province(No.20192ACB80001)the National Natural Science Foundation of China(Nos.52171163,51701214 and U1908219)。
文摘Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses.Using the realizable k-εmodel and discrete phase model theory,the flow dynamics of the gas phase and gas-melt two-phase flow felds in the close-wake condition were investigated to establish the correlation between high gas pressure and powder particle characteristics.The locations of the recirculation zones and the shapes of Mach disks were analyzed in detail for the type of discrete-jet closed-coupled gas atomization nozzle.In the gas-phase flow feld,the vortexes,closed to the Mach disk,are found to be a new deceleration method.In the two-phase flow feld,the shape of Mach disk changes from“S”-shape to“Z”-shape under the impact of the droplet flow.As predicted by the wave model,with the elevation of gas pressure,the size of the particle is found to gradually decrease and its distribution becomes more concentrated.Simulation results were compliant with the Fe-based amorphous alloy powder preparation tests.This study deepens the understanding of the gas pressure impacting particle features via gas atomization,and contributes to technological applications.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 51271081 and 51301072)partially supported by the Key Fundamental Research Project from Shenzhen Research Council (No. JC201105170745A)
文摘In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) spraying.The microstructure of the composite coatings was systematically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The main structure of composite coatings remained amorphous while 31 6L stainless steel splats were distributed homogeneously in the amorphous matrix and well connected with surrounding amorphous phase.Bonding strength of coatings to the substrate was determined by 'pull-off' tensile tests.The results revealed that the31 6L stainless steel phase effectively improved the bonding strength of amorphous coatings,which is mainly contributed by the strong metallurgical bonding between stainless steel and amorphous splats.The addition of31 6L stainless steel also enhanced the ductility and fracture resistance of the coatings due to the ductile stainless steel phases,which can arrest crack propagation and increase energy dissipation.
基金supported by the National Natural Science Foun-dation of China (No.52174217)China Postdoctoral Science Foundation (No.2020M682495).
文摘Designing low melting point and low basicity refining slag suitable for Fe-based amorphous alloys and understanding the inclusions’formation,removal,influencing mechanisms are quite vital in the fields of metallurgy and materials.In this study,a novel 13%SiO_(2)-32%CaO-30%Al_(2)O_(3)-25%B_(2)O_(3)(wt.%)refining slag was designed after careful calculations of the liquid phase region,slag-metal equilibrium,surface tension,viscosity,deoxidation capability and sulfur distribution ratio.After refining with our designed slag,the content of impurities and the number density of inclusions in a representative Fe_(83)Si_(2)B_(15)(at.%)amor-phous alloy were significantly reduced.Moreover,the glass-forming ability(GFA)of the alloy was also enhanced,enabling the preparation of amorphous ribbons with a lower cooling rate.Based on the impu-rities in Fe-based amorphous alloys as well as the calculated oxide and sulfide free energy diagrams,CaO,SiO_(2),Al_(2)O_(3) oxides and CaS,TiS,MnS sulfides will form in the master alloy.The high melting point in-clusions in the melt are generally removed via a floatation-separation-absorption process and the Mn,Ti,S impurities are removed via slag-metal interface reactions during refining.As for the detrimental effect of inclusions on glass formation,the small lattice disregistry between Ti,Mn-containing inclusions and primaryα-Fe gains reveal that these inclusions are effective in promoting the heterogeneous nucleation,and therefore greatly deteriorate the GFA.These findings are important and provide an ideal solution to purifying the Fe-based amorphous alloys by refining and enhancing the GFA for industrial production.
基金financially supported by the National Natural Science Foundation of China (Nos. 52061135207, 51871016, 51921001, 5197011039, 5197011018, and U20b200318)the China Nuclear Power Technology Research Institute Co., Ltd
文摘The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance of T91 stainless steel in liquid lead-bismuth eutectic(LBE).The corrosion behavior of the T91 steel and coating exposed to oxygen-saturated LBE at 400℃ for 500 h was investigated.Results showed that the T91 substrate was severely corroded and covered by a homogeneously distributed dual-layer oxide on the interface contacted to LBE,consisting of an outer magnetite layer and an inner Fe-Cr spinel layer.Meanwhile,the amorphous coating with a high glass transition temperature(Tg=550℃)and crystallization temperature(T_(x)=600℃)exhibited dramatically enhanced thermal stability and corrosion resistance.No visible LBE penetration was observed,although small amounts of Fe_(3)O_(4),Cr_(2)O_(3),and PbO were found on the coating surface.In addition,the amorphicity and interface bonding of the coating layer remained unchanged after the LBE corrosion.The Fe-based amorphous coating can act as a stable barrier layer in liquid LBE and have great application potential for long-term service in LBE-cooled fast reactors.
基金Project(EA201103238)supported by Nanchang Hangkong University Doctor Startup Fund,China
文摘The Fe-based amorphous metallic matrix coating （Fe-AMMC） was fabricated with the powder mixtures of Fe-based metallic glass synthesized with industrial raw materials, NiCr alloy and WC particle by high velocity oxy-fuel （HVOF） spraying. The corrosion resistance of Fe-AMMC was investigated by potentiodynamic polarization tests in 1 mol/L HCl, NaCl, H2SO4 and NaOH solutions, respectively. The surface morphologies corroded were observed by SEM. The results indicate that Fe-AMMC exhibits excellent corrosion resistance, higher corrosion resistance than 304L stainless steel in the chloride solutions. The low corrosion current density and passive current density of Fe-AMMC with a wide spontaneous passivation region are about 132.0μA/cm2 and 9.0 mA/cm2 in HCl solution, and about 2.5 μA/cm2 and 2.3 mA/cm2 in NaCl solution. The excellent corrosion resistance demonstrates that Fe-based amorphous metallic matrix powder is a viable engineering material in practical anti-corrosion and anti-wear coating applications.
基金Item Sponsored by National Natural Science Foundation of China(51205001)Key Project of Natural Science of Education Department of Anhui Province of China(KJ2014A023)Scientific Research Starting Foundation of Anhui Polytechnic University of China(2012YQQ006)
文摘Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.
基金financially supported by the National Natural Science Foundation of China(Nos.51901092,52075234)the Program of"Science and Technology International Cooperation Demonstrative Base of Metal Surface Engineering along the Silk Road(No.2017D01003)"+3 种基金the"111"project(No.D21032)the Key Research Program of Education Department of Gansu Province(No.GSSYLXM-03)the Natural Science Foundation of Gansu Province(No.20JR5RA431)Hongliu Distinguished Young Talent Support Program of Lanzhou University of Technology,and the Open Fund Project of Hunan Province Key Laboratory of Electromagnetic Equipment Design and Manufacturing,Hunan Institute of Technology(No.DC202001)。
文摘Amorphous alloys without crystalline defects(dislocation,crystal boundary)are ideal hydrophobic coating materials due to their low surface energy.This work used a synergistic method of detonation spraying and surface modification to obtain the superhydrophobic Febased amorphous coatings with high hardness and dense structure on the Q 235 substrate.The results showed that the water contact angles(WCA)of the superhydrophobic coating was 160°±3.6°,and water droplets could bounce off the superhydrophobic coating surface,illustrating the excellent self-cleaning performance of coating.Notably,the corrosion current density(i_(corr))of the superhydrophobic coating further decreased by 2 orders of magnitude down to8.008×10^(-8)A·cm^(-2)compared to the as-deposited coating with 5.473×10^(-6)A·cm^(-2);the corrosion potential(E_(corr))of the superhydrophobic coating shifted by 34 mV to the positive side compared with that of the as-deposited coating(-310 mV).Likewise,the impedance modulus|Z|values of the superhydrophobic coating increased by nearly2 orders of magnitude up to 1×10^(5.6)compared to the asdeposited coating with 1×10^(3.8).Even through lasting immersion in NaCl for 10 days,|Z|values of the superhydrophobic coating were still much higher than those of the as-deposited coating.The superhydrophobic Fe-based amorphous coatings could respond to their applications under extreme conditions due to their excellent hydrophobicity and self-cleaning properties,illustrating their promising future in aerospace,automotive,and machinery industries.
基金supported by GuangDong Basic and Applied Basic Research Foundation(No.2020A1515110128).
文摘Hot corrosion behaviors of the 921A alloy and Fe-based amorphous coating induced by KCl-10% ZnCl_(2) and KCl-55% ZnCl_(2) salts at 450℃ in air for 40 h were investigated.Results show that the 921A alloy suffers more serious corrosion damage than the coating and KCl-55% ZnCl_(2) salts are more corrosive than KCl-10% ZnCl_(2) salts.In the two salts,an Fe_(2)O_(3) layer is formed on the 921A alloy surface,while an outer Fe-rich oxide layer and an inner Cr-rich oxide layer are formed on the surface of the coating.Moreover,a certain amount of metal chloride can be found at the oxide/alloy(coating)interface,which can be explained by "active oxidation".However,the corrosion resistance of the Fe-based amorphous coating did not achieve the desired results,probably because the intersplats in the coating serve as corrosion diffusing channels,which facilitate the corrosion damage rate.Nevertheless,the coating is still in amorphous state after hot corrosion exposure.
基金financially supported by the National Key Research and Development Program of China(No.2016YFC0801905)。
文摘A new Fe-based amorphous–crystalline composite without non-metallic elements, Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5), was prepared by melt-spinning. The formation ability and structure information were investigated by X-ray diffractometer(XRD), energy-dispersive spectrometer(EDS) and scanning electron microscope(SEM). The mechanical properties of the amorphous–crystalline composite were investigated by nanoindentation. A molecular dynamics simulation study was performed to simulate the formation of Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5) amorphous alloy. The mechanical properties were obtained by compression simulations simultaneously. The results indicate that the Fe_(55)Cr_(15)Mo_(15)Ni_(10)W_(5) ribbon is an amorphous–crystalline composite structure with good ductility, and the hardness of the amorphous–crystalline composite is about 75%higher than that of master ingot. The simulation mechanical properties are in good agreement with the results of nanoindentation at the nanoscale.
基金financially supported by the National Natural Science Foundation of China(Nos.52174217 and 52304354)the China Postdoctoral Science Foundation(No.2020M682495)。
文摘Separated preparation of prealloys and amorphous alloys results in severe solidification-remelting and beneficial element removal-readdition contradictions,which markedly increase energy consumption and emissions.This study offered a novel strategy for the direct production of FePC amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore(HPIO)and apatite.First,the thermodynamic conditions and equilibrium states of the carbothermal reduction reactions in HPIO were calculated,and the element content in reduced alloys was theoretically determined.The phase and structural evolutions,as well as element migration and enrichment behaviors during the smelting reduction of HPIO and Ca_(3)(PO_(4))_(2),were then experimentally verified.The addition of Ca_(3)(PO_(4))_(2)in HPIO contributes to the enrichment of the P element in reduced alloys and the subsequent development of Fe_(3)P and Fe_(2)P phases.The content of P and C elements in the range of 1.52 wt% -14.63 wt% and 0.62 wt% -2.47 wt%,respectively,can be well tailored by adding 0-50 g Ca_(3)(PO_(4))_(2)and controlling the C/O mole ratio of 0.8-1.1,which is highly consistent with the calculated results.These FePC alloys were then successfully formed into amorphous ribbons and rods.The energy consumption of the proposed strategy was estimated to be 2.00×10^(8) kJ/t,which is reduced by 30% when compared with the conventional production process.These results are critical for the comprehensive utilization of mineral resources and pave the way for the clean production of Fe-based amorphous soft magnetic alloys.
基金Project supported by the National Key Research and Development Program of China(Grant No.2016YFB0300502)the Shenzhen Municipal Fundamental Science and Technology Research Program,China(Grant No.JCYJ20170815162201821)the Fundamental Research Funds for Central Universities,China(Grant No.31020170QD102)
文摘The addition of early transition metals(ETMs)into Fe-based amorphous alloys is practically found to be effective in reducing theα-Fe grain size in crystallization process.In this paper,by using ab initio molecular dynamics simulations,the mechanism of the effect of two typical ETMs(Nb and W)on nano-crystallization is studied.It is found that the diffusion ability in amorphous alloy is mainly determined by the bonding energy of the atom rather than the size or weight of the atom.The alloying of B dramatically reduces the diffusion ability of the ETM atoms,which prevents the supply of Fe near the grain surface and consequently suppresses the growth ofα-Fe grains.Moreover,the difference in grain refining effectiveness between Nb and W could be attributed to the larger bonding energy between Nb and B than that between W and B.
基金Funded by the National Natural Science Foundation of China(No.51965044)the Basic Pre Research of General Armament Department(No.41423060313)。
文摘The effects of kerosene flow rate on the microstructure and wearing properties were investigated for Fe-based amorphous coatings sprayed by High Velocity Oxygen Fuel (HVOF).The microstructures and wearing properties of the Fe-based amorphous coatings were analyzed with scanning electron microscope (SEM),X-ray diffraction analyzer (XRD),and ball-on-disc tribometer (CFT-1),respectively.The experimental results show that the well interfacial bonding can be observed between the amorphous coating layer and the substrate,and the porosity in amorphous coating layer is less to 1%.Only some crystalline a-Fe and FeO phases can be detected by XRD in the amorphous coatings,while the amorphous content is up to 99.4%.The wearing coefficient is near to 0.15,which is superior to SUS316 of 0.28.As the increasing of wearing loads,the failure mode is changed from oxidation wear to the composite of oxidation and abrasive wear.
文摘Substituting boron for carbon can improve the corrosion behavior of Fe-based amorphous significantly especially in acid solution with saturated H_2S. XPS analysis proves that boron enriches in the surface layer of amorphous and reacts with hydrogen to form B_(10)H_(14) . It efficiently prevents the intrusion of hydrogen to the sample, thus the destructive effect of hydrogen can be decreased greatly.
文摘A ferromagnetic amorphous Fe73Al4Ge2Nb1P10C6B4 alloy with high glass-forming ability was synthesized by melt spinning. The supercooled liquid region before crystallization reaches about 65.7 K. The crystallized structure consists of alpha -Fe, Fe3B, FeB, Fe3P and Fe3C phases. The Fe-based amorphous alloy exhibits good magnetic properties with a high saturation magnetization and a low saturated magnetostriction. The crystallization leads to an obvious decrease in the soft magnetic properties.
文摘Amorphous metallic coatings with a composition of Fe48Cr15Mo14C15B6Y2 were prepared by detonation gun spraying process. Microstructural studies show that the coatings present a densely layered structure typical of thermally sprayed deposits with the porosity below 2%. Both crystallization and oxidation occurred obviously during spraying process, so that the amorphous fraction of the coatings decreased to 54% compared with fully amorphous alloy ribbons of the same component. Corrosion behavior of the amorphous coatings was investigated by electrochemical measurement. The results show that the coatings exhibit extremely wide passive region and low passive current density in 3.5% NaCl (mass fraction) and 1 mol/L HCl solutions, which illustrates excellent ability to resist localized corrosion.
