Owing to the presence of large residual internal stress during cold compaction,it is difficult to optimize the multiple high-frequency magnetic properties of amorphous soft magnetic composites(ASMCs)simultaneously.Her...Owing to the presence of large residual internal stress during cold compaction,it is difficult to optimize the multiple high-frequency magnetic properties of amorphous soft magnetic composites(ASMCs)simultaneously.Here,a surface nanoengineering strategy was proposed to address the above dilemma by constructing a stress buffer layer composed of amorphous nano-particles,between amorphous powder and insulation coating.The amorphous FeSiBCCr@x wt.%FeB(x=0.5,1,3)composite powders with coreshell structures were successfully prepared via an in-situ chemical reduction method.Especially,when the composite ratio of nano-particles is 1 wt.%,the comprehensive properties of the ASMC reach the best balance.Compared with the FeSiBCCr ASMC,the saturation magnetization of the modified ASMC enhances from 153 to 171 emu/g.Meanwhile,the core loss decreases by 28.25%,while the effective permeability increases by 25% and can stabilize to∼20 MHz.Therefore,our work provides a strategy for achieving superior comprehensive soft magnetic properties of ASMCs via surface nanoengineering,which presents enormous application potential in high-frequency electric devices.展开更多
The poor surface antibacterial properties are one of the important factors limiting the application of Carbon Fibers Reinforced Polyetheretherketone (CFR-P) composites as artificial bone replace materials. Some of the...The poor surface antibacterial properties are one of the important factors limiting the application of Carbon Fibers Reinforced Polyetheretherketone (CFR-P) composites as artificial bone replace materials. Some of the Two-Dimensional (2D) nanomaterials with unique lamellar structures and biological properties have been demonstrated to have excellent antibacterial properties. Antibacterial properties can be improved by feasible chemical strategies for preparing 2D nanomaterials coating on the surface of CFR-P. In this work, Black Phosphorus (BP) coating was prepared on the originally chemically inert CFR-P surface based on wet chemical pretreatment. The physical and chemical properties, including surface microstructure, chemical composition and state, roughness and hydrophilicity were characterized. The antibacterial ratios against Staphylococcus aureus (S. aureus), Escherichia coli (E. coli), and Streptococcus mutans (S. mutans) were evaluated. The results indicated that hydrophilicity of BP coating on CFR-P was significantly higher compared to that of the pure CFR-P. Wet chemical pretreatment using mixed acid reagents (concentrated sulfuric acid and concentrated nitric acid) introduced hydroxyl, carboxyl and nitro groups on CFR-P. The BP coating exhibited the antibacterial rate of over 98% against both S. aureus and E. coli. In addition, the antibacterial rate of BP coating against the main pathogenic bacteria of dental caries, Streptococcus mutans, reached 45%.展开更多
Magnesium(Mg)-based materials are promising for lightweight structural applications.However,their widespread adoption is significantly constrained by inherent limitations in mechanical properties.To address this chall...Magnesium(Mg)-based materials are promising for lightweight structural applications.However,their widespread adoption is significantly constrained by inherent limitations in mechanical properties.To address this challenge,this study introduces a novel Mg-based interpenetratingphase composite reinforced with a nickel-titanium(NiTi)scaffold featuring a triply periodic minimal surface(TPMS)configuration.By combining experimental investigations with finite element simulations,we systematically elucidate the dual impact of the scaffold’s unit cell size(a)on manufacturing viability and mechanical enhancement.To compensate for compromised infiltration dynamics induced by decreasing a,a critical permeability threshold of 1×10^(-8) m^(2) is proposed for achieving successful composite fabrication.Mechanically,reducing a strengthens the interaction between the scaffold and matrix:the TPMS-configured NiTi scaffolds improve stress transfer,deflect crack propagation,and facilitate damage delocalization,whereas the Mg matrix preserves structural integrity and enables load redistribution.Consequently,the composites significantly outperform pure Mg,and lowering a leads to more substantial enhancements in compressive strength,energy dissipation,and deformation recoverability.This study offers valuable insight into the design and fabrication of highperformance Mg-based materials for structural and biomedical applications.展开更多
Practical applications of desulfurization gypsum are limited owing to its brittleness and low strength.To overcome these challenges,researchers have developed engineered desulfurization gypsum composites(EDGCs)by inco...Practical applications of desulfurization gypsum are limited owing to its brittleness and low strength.To overcome these challenges,researchers have developed engineered desulfurization gypsum composites(EDGCs)by incorporating ultrahigh molecular weight polyethylene(UHMWPE)fiber and sulfoaluminate cement(SAC).The mix ratio was optimized using response surface methodology(RSM).Experimental testing of EDGC under compressive and tensile loads led to the creation of a regression model that investigates the influence of variables and their interactions on the material’s compressive and tensile strengths.Additionally,microscopic morphology and hydration product composition were analyzed to explore the influence mechanism.The results indicated that EDGC’s compressive strength increased by up to 38.4%owing to a decreased water-binder ratio and higher SAC content.Similarly,tensile strength increased by up to 38.6%owing to increased SAC and fiber content.Moreover,EDGC demonstrated excellent strain-hardening behavior and multiple cracking characteristics,achieving a maximum tensile strain of nearly 3%.The research findings provide valuable insights for optimizing the performance of desulfurization gypsum.展开更多
An effective optimization method for the shape/sizing design of composite wing structures is presented with satisfying weight-cutting results. After decoupling, a kind of two-layer cycled optimization strategy suitabl...An effective optimization method for the shape/sizing design of composite wing structures is presented with satisfying weight-cutting results. After decoupling, a kind of two-layer cycled optimization strategy suitable for these integrated shape/sizing optimization is obtained. The uniform design method is used to provide sample points, and approximation models for shape design variables. And the results of sizing optimization are construct- ed with the quadratic response surface method （QRSM）. The complex method based on QRSM is used to opti- mize the shape design variables and the criteria method is adopted to optimize the sizing design variables. Compared with the conventional method, the proposed algorithm is more effective and feasible for solving complex composite optimization problems and has good efficiency in weight cutting.展开更多
Surface notches lower the stiffness of laminated strips, so they lower the buckling loads of the laminated strips, too. In this paper a new method is proposed to predict the buckling loads of the laminated strips with...Surface notches lower the stiffness of laminated strips, so they lower the buckling loads of the laminated strips, too. In this paper a new method is proposed to predict the buckling loads of the laminated strips with a surface notch. The theoretical and experimental results show that the buckling loads decrease as the depth or width of the surface notches increase; when the stacking sequence of the laminated strips is [0°/0°/+ θ/-θ/0°/0°/+θ/-θ] s , the buckling load decrease as θ increases. It proves that the method is reliable and significant.展开更多
Neural-Network Response Surfaces （NNRS） is applied to replace the actual expensive finite element analysis during the composite structural optimization process. The Orthotropic Experiment Method （OEM） is used to s...Neural-Network Response Surfaces （NNRS） is applied to replace the actual expensive finite element analysis during the composite structural optimization process. The Orthotropic Experiment Method （OEM） is used to select the most appropriate design samples for network training. The trained response surfaces can either be objective function or constraint conditions. Together with other conven- tional constraints, an optimization model is then set up and can be solved by Genetic Algorithm （GA）. This allows the separation between design analysis modeling and optimization searching. Through an example of a hat-stiffened composite plate design, the weight response surface is constructed to be objective function, and strength and buckling response surfaces as constraints; and all of them are trained through NASTRAN finite element analysis. The results of optimization study illustrate that the cycles of structural analysis ean be remarkably reduced or even eliminated during the optimization, thus greatly raising the efficiency of optimization process. It also observed that NNRS approximation can achieve equal or even better accuracy than conventional functional response surfaces.展开更多
This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of lo...This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.展开更多
The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microst...The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microstructure and wear performance of the composite coatings were investigated by X-ray diffraction(XRD),scanning electron microscope(SEM),energy dispersive spectrometer(EDS)and ball-disc wear tests.The results show that the clad coatings contain mainly?-Fe,WC and carbides(Cr23C6,Fe3W3C-Fe4W2C)phases and the precipitation of carbides increases with the increase of WC-Co doping content.The WC-Co doping content has an obvious effect on the microstructure of the clad coatings.For the clad coatings with low WC-Co doping,the microstructure gradually transforms from planar crystal at the interface of substrate/coating to cell/dendritic crystal at the middle and the upper portion of the coatings.But there are a number of fishbone-like structure at the middle and the upper portion of clad coating with 40wt%WC-Co doping.The microstructure at the top is smaller than that at the bottom for all the coatings.The maximum of hardness of the clad coatings is 72.3HRC which is about 6.9 as much as the hardness of Q235 steel substrate.The composite coatings have good wear resistance due to the reinforcement of carbide particles and the strong bonding between carbide particles and ferroalloy.The suitable increase of WC-Co doping content can improve the wear resistance of the composite coatings.展开更多
The present investigation focuses on the parametric influence of machining parameters on the surface finish obtained in turning of glass fiber reinforced polymer （GFRP） composites. The experiments were conducted bas...The present investigation focuses on the parametric influence of machining parameters on the surface finish obtained in turning of glass fiber reinforced polymer （GFRP） composites. The experiments were conducted based on Taguchi＇s experimental design technique. Response surface methodology and analysis of variance （ANOVA） were used to evaluate the composite machining process to perform the optimization. The results revealed that the feed rate was main influencing parameter on the surface roughness. The surface roughness increased with increasing the feed rate but decreased with increasing the cutting speed. Among the other parameters, depth of cut was more insensitive. The predicted values and measured values were fairly close to each other, which indicates that the developed model can be effectively used to predict the surface roughness on the machining of GFRP composites with 95% confidence intervals. Using such model could remarkablely save the time and cost.展开更多
The effect of rare earths （RE） surface treatment of carbon fibers （CF） on tribological properties of CF reinforced polytetrafluoroethylene （PTFE） composites under oil-lubricated condition was investigated. Exper...The effect of rare earths （RE） surface treatment of carbon fibers （CF） on tribological properties of CF reinforced polytetrafluoroethylene （PTFE） composites under oil-lubricated condition was investigated. Experimental results revealed that RE treated CF reinforced PTFE （CF/PTFE） composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air-oxidated composites. X-ray photoelectron spectroscopy （XPS） study of carbon fiber surface showed that, after RE treatment, oxygen concentration increased obviously, and the amount of oxygen-containing groups on CF surfaces were largely increased. The increase in the amount of oxygen-containing groups enhanced interfacial adhesion between CF and PTFE matrix. With strong interfacial adhesion of the composite, stress could be effectively transmitted to carbon fibers; carbon fibers were strongly bonded with VITE matrix, and large scale rubbing-off of PTFE be prevented, therefore, tribological properties of the composite was improved.展开更多
With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawat...With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.展开更多
The functional groups on graphene sheets surface affect their dispersion and interfacial adhesion in polymer matrix. We compared the mechanical property of polymethymethacrylate（PMMA） microcellular foams reinforced ...The functional groups on graphene sheets surface affect their dispersion and interfacial adhesion in polymer matrix. We compared the mechanical property of polymethymethacrylate（PMMA） microcellular foams reinforced with graphene oxide（GO） and reduced graphene oxide（RGO） to investigate this influence of functional groups. RGO sheets were fabricated by solvent thermal reduction in DMF medium. UV-Vis, FT-IR and XPS analyses indicate the difference of oxygen-containing groups on GO and RGO sheets surface. The observation of SEM illustrates that the addition of a smaller number of GO or RGO sheets causes a fine cellular structure of PMMA foams with a higher cell density(about 1011 cells/cm3) and smaller cell sizes（about 1-2 μm） owing to their remarkable heterogeneous nucleation effect. Compared to GO reinforced foams, the RGO/PMMA foams own lower cell density and bigger cell size in their microstructure, and their compressive strength is lower even when the reinforcement contents are the same and the foam bulk density is higher. These results indicate that the oxygen-containing groups on GO sheets’ surface are beneficial to adhere CO2 to realize a larger nucleation rate, and their strong interaction with PMMA matrix improves the mechanical property of PMMA foams.展开更多
The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating...The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating progress. The microstructure was observed by scanning electron microscopy(SEM); the phase constitutions was analyzed by X-ray diffraction(XRD); and the hardness and wear resistance of selected specimens were tested by hardness testing machine and abrasion testing machine, respectively. The addition of high carbon ferrochromium powders leads to the formation of white iron during solidifi cation. The wear volume loss rates of ATZ ceramic particle reinforced gray iron matrix surface composite decreases fi rst, and then tends to be stable. The wear resistance of the composite is 2.7 times higher than that of gray iron matrix. The reason is a combination of the surface hardness increase of gray iron matrix and ATZ ceramic particles and alloy carbides protecting effect on gray iron matrix.展开更多
In the present work, the surface characteristics of Electrical Discharge Machined (EDM) Al (6351)eSiC and Al (6351)eSiCeB4C composites are investigated. The composites are prepared by employing the conventional stir c...In the present work, the surface characteristics of Electrical Discharge Machined (EDM) Al (6351)eSiC and Al (6351)eSiCeB4C composites are investigated. The composites are prepared by employing the conventional stir casting technique, as it can produce better particle dispersion in the matrix. The detailed experimental study is performed on the composites by varying current (I), duty factor (t), pulse on time (Ton), and the gap voltage (V) in order to analyze the Heat Affected Zone (HAZ) formed in the sub surface and the average crater diameter formed on the machined surface of the composites as an output function. The formation of recast layers, presence of bubbles and the surface texture of the composites at various machining conditions are observed. The results show that the increased Metal Removal Rate (MRR) increases the depth of HAZ and the average crater diameter on the machined area. Further, the addition of B4C particles to the composite produces more surface defect than the AleSiC composite.展开更多
In this paper, we report the use of blowing nitrogen gas for the successful fabrication of a composite layer composed of Ti/TiN on a substrate of commercially pure titanium （cp-2） using the friction stir processing ...In this paper, we report the use of blowing nitrogen gas for the successful fabrication of a composite layer composed of Ti/TiN on a substrate of commercially pure titanium （cp-2） using the friction stir processing technique. The prepared composite layer was characterized by X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray spectrometry. The maximum microhardness of the Ti/TiN composite reached 1024 HV, which is 6.4 times higher than that of the titanium substrate. The results of wear test indicated that the Ti/TiN composite layer possesses excellent abrasive and adhesive wear resistance because of the formation of the TiN and its high hardness.展开更多
In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties.However,the hard ceramic particles as the reinforcement phase bring challenges to machi...In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties.However,the hard ceramic particles as the reinforcement phase bring challenges to machining.To study the effect of in-situ TiB_(2)particles on machinability and surface integrity of TiB_(2)/2024 composite and TiB_(2)/7075 composite,milling experiments were performed,and compared with conventional 2024 and 7075 aluminum alloys.In-situ TiB_(2)particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy.Therefore,the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity.In the milling of composites,abrasive wear is the main wear form of carbide tools,due to the scratching of hard nano-TiB_(2)particles.The composites containing in-situ TiB_(2)particles have machining defects such as smearing,micro-scratches,micro-pits and tail on the machined surface.However,in-situ TiB_(2)particles impede the plastic deformation of the composites,which greatly reduces cutting edge marks on the machined surface.Therefore,under the same milling parameters,the surface roughness of TiB_(2)/2024 composite and TiB_(2)/7075 composite is much less than that of2024 and 7075 aluminum alloy respectively.Under the milling conditions of this experiment,the machined subsurface has no metamorphic layer,and the microhardness of the machined surface is almost the same as that of the material.Besides,compared with 2024 and 7075 aluminum alloy,machined surfaces of TiB_(2)/2024 composite and TiB_(2)/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.展开更多
The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with C...The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.展开更多
Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force ap...Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.展开更多
The quality of surface generated in a peripheral milling of AZ91/SiCp/15%for varying machining conditions and its effect on the fatigue performance are investigated in this study.The machined surface quality was evalu...The quality of surface generated in a peripheral milling of AZ91/SiCp/15%for varying machining conditions and its effect on the fatigue performance are investigated in this study.The machined surface quality was evaluated through roughness measurements and SEM micrographs of ine machined surface.Tensile iesis were pcifumicu io iiieasure the mechanical properties of the composite.Subsequently,fatigue life of milled specimens was measured through axial fatigue tests at four loading conditions.Optical and SEM/EDS micrographs of the fractured surface were studied to identify the crack initiation site and propagation mechanism.Specimens machined at a lower feed rate of 0.1 mm/rev was found to have excellent surface finish and consequently higher fatigue life.At 0.3 mm/rev,the presence of feed marks and other surface defects resulted in a drastic decrease in fatigue life.Five distinct regions were identified on the fractured surface,particle fracture along and perpendicular to the surface,voids in the matrix due to particle debonding and pull out and typical ductile failure of matrix with embedded SiC particles.展开更多
基金financially supported by Guangdong Major Project of Basic and Applied Basic Research,China(No.2019B030302010)the National Natural Science Foundation of China(Nos.52071222,52301212,52101191,52192601,52192602,52192603)+1 种基金the National Key Research and Development Program of China(No.2021YFA0716302)Dongguan Key Research and Development Projects(No.20221200300062).
文摘Owing to the presence of large residual internal stress during cold compaction,it is difficult to optimize the multiple high-frequency magnetic properties of amorphous soft magnetic composites(ASMCs)simultaneously.Here,a surface nanoengineering strategy was proposed to address the above dilemma by constructing a stress buffer layer composed of amorphous nano-particles,between amorphous powder and insulation coating.The amorphous FeSiBCCr@x wt.%FeB(x=0.5,1,3)composite powders with coreshell structures were successfully prepared via an in-situ chemical reduction method.Especially,when the composite ratio of nano-particles is 1 wt.%,the comprehensive properties of the ASMC reach the best balance.Compared with the FeSiBCCr ASMC,the saturation magnetization of the modified ASMC enhances from 153 to 171 emu/g.Meanwhile,the core loss decreases by 28.25%,while the effective permeability increases by 25% and can stabilize to∼20 MHz.Therefore,our work provides a strategy for achieving superior comprehensive soft magnetic properties of ASMCs via surface nanoengineering,which presents enormous application potential in high-frequency electric devices.
基金support of the National Natural Science Foundation of China(61971301)In part by the Central Guidance on Local Science and Technology Development Fund of Shanxi Province under Grant YDZJSX2021A018+1 种基金Shanxi Province Higher Education Science and Technology Innovation Plan Project(2022L060)the Fundamental Research Program of Shanxi Province(Nos.202203021212227,202303021212082).
文摘The poor surface antibacterial properties are one of the important factors limiting the application of Carbon Fibers Reinforced Polyetheretherketone (CFR-P) composites as artificial bone replace materials. Some of the Two-Dimensional (2D) nanomaterials with unique lamellar structures and biological properties have been demonstrated to have excellent antibacterial properties. Antibacterial properties can be improved by feasible chemical strategies for preparing 2D nanomaterials coating on the surface of CFR-P. In this work, Black Phosphorus (BP) coating was prepared on the originally chemically inert CFR-P surface based on wet chemical pretreatment. The physical and chemical properties, including surface microstructure, chemical composition and state, roughness and hydrophilicity were characterized. The antibacterial ratios against Staphylococcus aureus (S. aureus), Escherichia coli (E. coli), and Streptococcus mutans (S. mutans) were evaluated. The results indicated that hydrophilicity of BP coating on CFR-P was significantly higher compared to that of the pure CFR-P. Wet chemical pretreatment using mixed acid reagents (concentrated sulfuric acid and concentrated nitric acid) introduced hydroxyl, carboxyl and nitro groups on CFR-P. The BP coating exhibited the antibacterial rate of over 98% against both S. aureus and E. coli. In addition, the antibacterial rate of BP coating against the main pathogenic bacteria of dental caries, Streptococcus mutans, reached 45%.
基金supported by the Mainland-Hong Kong Joint Funding Scheme(MHKJFS)(Project No:MHP/040/22)RGC Theme-based Research Scheme AoE/M-402/20+1 种基金National Natural Science Foundation of China/Hong Kong Research Grants Council Joint Research Scheme(Project No:N_CityU151/23)Hong Kong Innovation and Technology Commission via the Hong Kong Branch of National Precious Metals Materials Engineering Research Center.
文摘Magnesium(Mg)-based materials are promising for lightweight structural applications.However,their widespread adoption is significantly constrained by inherent limitations in mechanical properties.To address this challenge,this study introduces a novel Mg-based interpenetratingphase composite reinforced with a nickel-titanium(NiTi)scaffold featuring a triply periodic minimal surface(TPMS)configuration.By combining experimental investigations with finite element simulations,we systematically elucidate the dual impact of the scaffold’s unit cell size(a)on manufacturing viability and mechanical enhancement.To compensate for compromised infiltration dynamics induced by decreasing a,a critical permeability threshold of 1×10^(-8) m^(2) is proposed for achieving successful composite fabrication.Mechanically,reducing a strengthens the interaction between the scaffold and matrix:the TPMS-configured NiTi scaffolds improve stress transfer,deflect crack propagation,and facilitate damage delocalization,whereas the Mg matrix preserves structural integrity and enables load redistribution.Consequently,the composites significantly outperform pure Mg,and lowering a leads to more substantial enhancements in compressive strength,energy dissipation,and deformation recoverability.This study offers valuable insight into the design and fabrication of highperformance Mg-based materials for structural and biomedical applications.
基金The National Natural Science Foundation of China(No.51978504).
文摘Practical applications of desulfurization gypsum are limited owing to its brittleness and low strength.To overcome these challenges,researchers have developed engineered desulfurization gypsum composites(EDGCs)by incorporating ultrahigh molecular weight polyethylene(UHMWPE)fiber and sulfoaluminate cement(SAC).The mix ratio was optimized using response surface methodology(RSM).Experimental testing of EDGC under compressive and tensile loads led to the creation of a regression model that investigates the influence of variables and their interactions on the material’s compressive and tensile strengths.Additionally,microscopic morphology and hydration product composition were analyzed to explore the influence mechanism.The results indicated that EDGC’s compressive strength increased by up to 38.4%owing to a decreased water-binder ratio and higher SAC content.Similarly,tensile strength increased by up to 38.6%owing to increased SAC and fiber content.Moreover,EDGC demonstrated excellent strain-hardening behavior and multiple cracking characteristics,achieving a maximum tensile strain of nearly 3%.The research findings provide valuable insights for optimizing the performance of desulfurization gypsum.
文摘An effective optimization method for the shape/sizing design of composite wing structures is presented with satisfying weight-cutting results. After decoupling, a kind of two-layer cycled optimization strategy suitable for these integrated shape/sizing optimization is obtained. The uniform design method is used to provide sample points, and approximation models for shape design variables. And the results of sizing optimization are construct- ed with the quadratic response surface method （QRSM）. The complex method based on QRSM is used to opti- mize the shape design variables and the criteria method is adopted to optimize the sizing design variables. Compared with the conventional method, the proposed algorithm is more effective and feasible for solving complex composite optimization problems and has good efficiency in weight cutting.
文摘Surface notches lower the stiffness of laminated strips, so they lower the buckling loads of the laminated strips, too. In this paper a new method is proposed to predict the buckling loads of the laminated strips with a surface notch. The theoretical and experimental results show that the buckling loads decrease as the depth or width of the surface notches increase; when the stacking sequence of the laminated strips is [0°/0°/+ θ/-θ/0°/0°/+θ/-θ] s , the buckling load decrease as θ increases. It proves that the method is reliable and significant.
文摘Neural-Network Response Surfaces （NNRS） is applied to replace the actual expensive finite element analysis during the composite structural optimization process. The Orthotropic Experiment Method （OEM） is used to select the most appropriate design samples for network training. The trained response surfaces can either be objective function or constraint conditions. Together with other conven- tional constraints, an optimization model is then set up and can be solved by Genetic Algorithm （GA）. This allows the separation between design analysis modeling and optimization searching. Through an example of a hat-stiffened composite plate design, the weight response surface is constructed to be objective function, and strength and buckling response surfaces as constraints; and all of them are trained through NASTRAN finite element analysis. The results of optimization study illustrate that the cycles of structural analysis ean be remarkably reduced or even eliminated during the optimization, thus greatly raising the efficiency of optimization process. It also observed that NNRS approximation can achieve equal or even better accuracy than conventional functional response surfaces.
文摘This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.
基金Fundamental Research Funds for the Central Universities(2009B16214)China Postdoctoral Science Foundation funded project(20100481079)Scientific Research Start-up Fund Project of Hohai University(20080403)
文摘The Fe-based WC composite coatings were clad on Q235 steel by double-pass plasma cladding method,in which the WC-Co(WC covered with cobalt:78wt%WC,12wt%Co)doping was about 10wt%,20wt%and 40wt%,respectively.The microstructure and wear performance of the composite coatings were investigated by X-ray diffraction(XRD),scanning electron microscope(SEM),energy dispersive spectrometer(EDS)and ball-disc wear tests.The results show that the clad coatings contain mainly?-Fe,WC and carbides(Cr23C6,Fe3W3C-Fe4W2C)phases and the precipitation of carbides increases with the increase of WC-Co doping content.The WC-Co doping content has an obvious effect on the microstructure of the clad coatings.For the clad coatings with low WC-Co doping,the microstructure gradually transforms from planar crystal at the interface of substrate/coating to cell/dendritic crystal at the middle and the upper portion of the coatings.But there are a number of fishbone-like structure at the middle and the upper portion of clad coating with 40wt%WC-Co doping.The microstructure at the top is smaller than that at the bottom for all the coatings.The maximum of hardness of the clad coatings is 72.3HRC which is about 6.9 as much as the hardness of Q235 steel substrate.The composite coatings have good wear resistance due to the reinforcement of carbide particles and the strong bonding between carbide particles and ferroalloy.The suitable increase of WC-Co doping content can improve the wear resistance of the composite coatings.
文摘The present investigation focuses on the parametric influence of machining parameters on the surface finish obtained in turning of glass fiber reinforced polymer （GFRP） composites. The experiments were conducted based on Taguchi＇s experimental design technique. Response surface methodology and analysis of variance （ANOVA） were used to evaluate the composite machining process to perform the optimization. The results revealed that the feed rate was main influencing parameter on the surface roughness. The surface roughness increased with increasing the feed rate but decreased with increasing the cutting speed. Among the other parameters, depth of cut was more insensitive. The predicted values and measured values were fairly close to each other, which indicates that the developed model can be effectively used to predict the surface roughness on the machining of GFRP composites with 95% confidence intervals. Using such model could remarkablely save the time and cost.
基金the National Natural Science Foundation of China (50275093)
文摘The effect of rare earths （RE） surface treatment of carbon fibers （CF） on tribological properties of CF reinforced polytetrafluoroethylene （PTFE） composites under oil-lubricated condition was investigated. Experimental results revealed that RE treated CF reinforced PTFE （CF/PTFE） composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air-oxidated composites. X-ray photoelectron spectroscopy （XPS） study of carbon fiber surface showed that, after RE treatment, oxygen concentration increased obviously, and the amount of oxygen-containing groups on CF surfaces were largely increased. The increase in the amount of oxygen-containing groups enhanced interfacial adhesion between CF and PTFE matrix. With strong interfacial adhesion of the composite, stress could be effectively transmitted to carbon fibers; carbon fibers were strongly bonded with VITE matrix, and large scale rubbing-off of PTFE be prevented, therefore, tribological properties of the composite was improved.
基金Supported by National Natural Science Foundation of China(Grant No.51375421)Hebei Provincial Key Project of Science and Technology Research of(ZD20131027)
文摘With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.
基金Funded by the National Nature Science Foundation of China(No.51521001)
文摘The functional groups on graphene sheets surface affect their dispersion and interfacial adhesion in polymer matrix. We compared the mechanical property of polymethymethacrylate（PMMA） microcellular foams reinforced with graphene oxide（GO） and reduced graphene oxide（RGO） to investigate this influence of functional groups. RGO sheets were fabricated by solvent thermal reduction in DMF medium. UV-Vis, FT-IR and XPS analyses indicate the difference of oxygen-containing groups on GO and RGO sheets surface. The observation of SEM illustrates that the addition of a smaller number of GO or RGO sheets causes a fine cellular structure of PMMA foams with a higher cell density(about 1011 cells/cm3) and smaller cell sizes（about 1-2 μm） owing to their remarkable heterogeneous nucleation effect. Compared to GO reinforced foams, the RGO/PMMA foams own lower cell density and bigger cell size in their microstructure, and their compressive strength is lower even when the reinforcement contents are the same and the foam bulk density is higher. These results indicate that the oxygen-containing groups on GO sheets’ surface are beneficial to adhere CO2 to realize a larger nucleation rate, and their strong interaction with PMMA matrix improves the mechanical property of PMMA foams.
基金financially supported by the Scientific Research Fund of Si Chuan Provincial Education Department(No.17ZA0395)the Doctoral Program Foundation of Southwest University of Science and Technology(No.10zx7113)
文摘The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating progress. The microstructure was observed by scanning electron microscopy(SEM); the phase constitutions was analyzed by X-ray diffraction(XRD); and the hardness and wear resistance of selected specimens were tested by hardness testing machine and abrasion testing machine, respectively. The addition of high carbon ferrochromium powders leads to the formation of white iron during solidifi cation. The wear volume loss rates of ATZ ceramic particle reinforced gray iron matrix surface composite decreases fi rst, and then tends to be stable. The wear resistance of the composite is 2.7 times higher than that of gray iron matrix. The reason is a combination of the surface hardness increase of gray iron matrix and ATZ ceramic particles and alloy carbides protecting effect on gray iron matrix.
文摘In the present work, the surface characteristics of Electrical Discharge Machined (EDM) Al (6351)eSiC and Al (6351)eSiCeB4C composites are investigated. The composites are prepared by employing the conventional stir casting technique, as it can produce better particle dispersion in the matrix. The detailed experimental study is performed on the composites by varying current (I), duty factor (t), pulse on time (Ton), and the gap voltage (V) in order to analyze the Heat Affected Zone (HAZ) formed in the sub surface and the average crater diameter formed on the machined surface of the composites as an output function. The formation of recast layers, presence of bubbles and the surface texture of the composites at various machining conditions are observed. The results show that the increased Metal Removal Rate (MRR) increases the depth of HAZ and the average crater diameter on the machined area. Further, the addition of B4C particles to the composite produces more surface defect than the AleSiC composite.
文摘In this paper, we report the use of blowing nitrogen gas for the successful fabrication of a composite layer composed of Ti/TiN on a substrate of commercially pure titanium （cp-2） using the friction stir processing technique. The prepared composite layer was characterized by X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray spectrometry. The maximum microhardness of the Ti/TiN composite reached 1024 HV, which is 6.4 times higher than that of the titanium substrate. The results of wear test indicated that the Ti/TiN composite layer possesses excellent abrasive and adhesive wear resistance because of the formation of the TiN and its high hardness.
基金the National Natural Science Foundation of China(No.51875356)。
文摘In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties.However,the hard ceramic particles as the reinforcement phase bring challenges to machining.To study the effect of in-situ TiB_(2)particles on machinability and surface integrity of TiB_(2)/2024 composite and TiB_(2)/7075 composite,milling experiments were performed,and compared with conventional 2024 and 7075 aluminum alloys.In-situ TiB_(2)particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy.Therefore,the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity.In the milling of composites,abrasive wear is the main wear form of carbide tools,due to the scratching of hard nano-TiB_(2)particles.The composites containing in-situ TiB_(2)particles have machining defects such as smearing,micro-scratches,micro-pits and tail on the machined surface.However,in-situ TiB_(2)particles impede the plastic deformation of the composites,which greatly reduces cutting edge marks on the machined surface.Therefore,under the same milling parameters,the surface roughness of TiB_(2)/2024 composite and TiB_(2)/7075 composite is much less than that of2024 and 7075 aluminum alloy respectively.Under the milling conditions of this experiment,the machined subsurface has no metamorphic layer,and the microhardness of the machined surface is almost the same as that of the material.Besides,compared with 2024 and 7075 aluminum alloy,machined surfaces of TiB_(2)/2024 composite and TiB_(2)/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.
基金Project(2017zzts111)supported by the Fundamental Research Funds for the Central Universities,China。
文摘The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.
基金supported by the National Natural Science Foundation of China(Grant No.50001008)the China Postdoctoral Science Foundation.
文摘Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.
基金This research work was financially supported through Boeing Pennell Professorship funds.
文摘The quality of surface generated in a peripheral milling of AZ91/SiCp/15%for varying machining conditions and its effect on the fatigue performance are investigated in this study.The machined surface quality was evaluated through roughness measurements and SEM micrographs of ine machined surface.Tensile iesis were pcifumicu io iiieasure the mechanical properties of the composite.Subsequently,fatigue life of milled specimens was measured through axial fatigue tests at four loading conditions.Optical and SEM/EDS micrographs of the fractured surface were studied to identify the crack initiation site and propagation mechanism.Specimens machined at a lower feed rate of 0.1 mm/rev was found to have excellent surface finish and consequently higher fatigue life.At 0.3 mm/rev,the presence of feed marks and other surface defects resulted in a drastic decrease in fatigue life.Five distinct regions were identified on the fractured surface,particle fracture along and perpendicular to the surface,voids in the matrix due to particle debonding and pull out and typical ductile failure of matrix with embedded SiC particles.
