采用光学显微镜(optical microscope,OM)、扫描电子显微镜(scanning electron microscope,SEM)、透射电子显微镜(transmission electron microscope,TEM)、硬度和电导率试验仪器,研究了Cu-Ni-Fe-P合金成分设计、微观结构和性能之间的构...采用光学显微镜(optical microscope,OM)、扫描电子显微镜(scanning electron microscope,SEM)、透射电子显微镜(transmission electron microscope,TEM)、硬度和电导率试验仪器,研究了Cu-Ni-Fe-P合金成分设计、微观结构和性能之间的构效关系。结果表明,Ni/Fe质量比对合金性能具有显著调控作用,当Ni/Fe质量比为3.00时,Cu-Ni-Fe-P合金在500℃时效0.50 h条件下维氏硬度达到峰值,为171.5,此时析出相平均尺寸为2.2 nm,随着时效时间延长至12.00 h时,析出相平均尺寸增大到5.6 nm。Fe元素的添加降低了溶质原子的固溶度,有效抑制了基体晶格畸变,提高了合金导电性,当Ni/Fe质量比为1.00时,Cu-Ni-Fe-P合金电导率在500℃/12.00 h时效条件下可达峰值63.6%IACS。其中,当Ni/Fe质量比为1.00时,500℃/6.00 h时效条件下,Cu-Ni-Fe-P合金的综合性能最好。展开更多
The microstructural evolution of Cu−19Ni−6Cr−7Mn alloy during aging treatment was investigated.After aging for 120 min at 500℃,the alloy exhibited excellent mechanical properties,including a tensile strength of 978 M...The microstructural evolution of Cu−19Ni−6Cr−7Mn alloy during aging treatment was investigated.After aging for 120 min at 500℃,the alloy exhibited excellent mechanical properties,including a tensile strength of 978 MPa and an elastic modulus of 145.8 GPa.After aging for 240 min at 500℃,the elastic modulus of the alloy reached 149.5 GPa,which was among the highest values reported for Cu alloys.It was worth mentioning that the tensile strength increased rapidly from 740 to 934 MPa after aging for 5 min at 500℃,which was close to the maximum tensile strength(978 MPa).Analysis of the underlying strengthening mechanisms and phase transformation behavior revealed that the Cu−19Ni−6Cr−7Mn alloy underwent spinodal decomposition and DO_(22) ordering during the first 5 min of aging at 500℃,and L1_(2) ordered phases and bcc-Cr precipitates appeared.Therefore,the enhanced mechanical properties of the Cu−19Ni−6Cr−7Mn alloy can be attributed to the stress field generated by spinodal decomposition and the presence of nanoscale ordered phase and Cr precipitates.展开更多
The creep response,mechanical properties,and microstructure evolution of the Al−Zn−Mg−Cu alloy were investigated under different initial heat treatment conditions.The results indicate that the density of geometrically...The creep response,mechanical properties,and microstructure evolution of the Al−Zn−Mg−Cu alloy were investigated under different initial heat treatment conditions.The results indicate that the density of geometrically necessary dislocations(GNDs)increases during the initial creep stage(<0.5 h)and undergoes dynamic changes in the stable creep stage.During creep aging,the dislocation distribution within the grains becomes more uniform,and additional subgrains are formed.The key factors influencing creep behavior are crystal orientation and the degree of initial precipitation.Grains oriented in the<001>and<101>directions are more susceptible to deformation during the creep process.Based on a strength model,the inhibitory effects of the η'phase in T6 specimens and the GP I zone in T4 specimens on dislocation motion were evaluated.This study demonstrates that selecting an appropriate initial precipitation state is an effective strategy to enhance the creep aging response and to produce high-performance components.展开更多
To investigate the influence of Al-Zn-Mg-Cu alloy with as-homogenized and as-rolled initial microstructures on the tensile flow behavior,isothermal tensile tests were conducted on a GLEEBLE-3500 isothermal simulator a...To investigate the influence of Al-Zn-Mg-Cu alloy with as-homogenized and as-rolled initial microstructures on the tensile flow behavior,isothermal tensile tests were conducted on a GLEEBLE-3500 isothermal simulator at temperatures of 380-440℃and strain rates of 0.05-1 s^(−1).The Johnson-Cook model,Hensel-Spittel model,strain-compensated Arrhenius model,and critical fracture strain model were established.Results show that through the evaluation of the models using the correlation coefficient(R)and the average absolute relative error,the strain-compensated Arrhenius model can represent the flow behavior of the alloy more accurately.Shear bands are more pronounced in the as-homogenized specimens,whereas dynamic recrystallization is predominantly observed in as-rolled specimens.Fracture morphology analysis reveals that a mixed fracture mechanism is prevalent in the as-homogenized specimen,whereas a ductile fracture mechanism is predominant in the as-rolled specimen.The processing maps indicate that the unstable region is reduced in the as-rolled specimens compared with that in the as-homogenized specimens.The optimal hot working windows for the as-homogenized and as-rolled specimens are determined as 410-440℃/0.14-1 s^(−1)and 380-400℃/0.05-0.29 s^(−1),respectively.展开更多
Texture and grain structure evolution during annealing and their effects on tensile strength and anisotropy were studied using XRD,DSC,SEM,EBSD and TEM.The results indicate that elevated rolling temperatures reduce th...Texture and grain structure evolution during annealing and their effects on tensile strength and anisotropy were studied using XRD,DSC,SEM,EBSD and TEM.The results indicate that elevated rolling temperatures reduce the f(g)_(max(Copper))/f(g)_(max(Brass))ratio,increase S-Brass fine bands,and promote S-dispersoid precipitation,leading to finer recrystallized grains.Dominant recrystallization textures transform from Goss+P to Goss and then to Goss+Cube with increasing rolling temperature.Annealing at 350℃shows four tensile strength response stages:fast softening I,rapid strengthening II,slow strengthening III,and slow softening IV.The transition from Stages I to II is driven by the formation of strong Goss and P textures,and Stage IV is linked to enhanced Cube texture.Plates with Goss+Cube textures and fine equiaxed grains exhibit the lowest YS/UTS ratio and minimal anisotropy.展开更多
基金supported by the National Key R&D Program of China (No. 2021YFB3700700)the Henan Province Top Talent Training Program Project, China (No. 244500510020)the High-level Talent Research Start-up Project Funding of Henan Academy of Sciences, China (No. 242017001)。
文摘The microstructural evolution of Cu−19Ni−6Cr−7Mn alloy during aging treatment was investigated.After aging for 120 min at 500℃,the alloy exhibited excellent mechanical properties,including a tensile strength of 978 MPa and an elastic modulus of 145.8 GPa.After aging for 240 min at 500℃,the elastic modulus of the alloy reached 149.5 GPa,which was among the highest values reported for Cu alloys.It was worth mentioning that the tensile strength increased rapidly from 740 to 934 MPa after aging for 5 min at 500℃,which was close to the maximum tensile strength(978 MPa).Analysis of the underlying strengthening mechanisms and phase transformation behavior revealed that the Cu−19Ni−6Cr−7Mn alloy underwent spinodal decomposition and DO_(22) ordering during the first 5 min of aging at 500℃,and L1_(2) ordered phases and bcc-Cr precipitates appeared.Therefore,the enhanced mechanical properties of the Cu−19Ni−6Cr−7Mn alloy can be attributed to the stress field generated by spinodal decomposition and the presence of nanoscale ordered phase and Cr precipitates.
基金support from the National Key Research and Development Program of China(No.2023YFB3710501)。
文摘The creep response,mechanical properties,and microstructure evolution of the Al−Zn−Mg−Cu alloy were investigated under different initial heat treatment conditions.The results indicate that the density of geometrically necessary dislocations(GNDs)increases during the initial creep stage(<0.5 h)and undergoes dynamic changes in the stable creep stage.During creep aging,the dislocation distribution within the grains becomes more uniform,and additional subgrains are formed.The key factors influencing creep behavior are crystal orientation and the degree of initial precipitation.Grains oriented in the<001>and<101>directions are more susceptible to deformation during the creep process.Based on a strength model,the inhibitory effects of the η'phase in T6 specimens and the GP I zone in T4 specimens on dislocation motion were evaluated.This study demonstrates that selecting an appropriate initial precipitation state is an effective strategy to enhance the creep aging response and to produce high-performance components.
文摘To investigate the influence of Al-Zn-Mg-Cu alloy with as-homogenized and as-rolled initial microstructures on the tensile flow behavior,isothermal tensile tests were conducted on a GLEEBLE-3500 isothermal simulator at temperatures of 380-440℃and strain rates of 0.05-1 s^(−1).The Johnson-Cook model,Hensel-Spittel model,strain-compensated Arrhenius model,and critical fracture strain model were established.Results show that through the evaluation of the models using the correlation coefficient(R)and the average absolute relative error,the strain-compensated Arrhenius model can represent the flow behavior of the alloy more accurately.Shear bands are more pronounced in the as-homogenized specimens,whereas dynamic recrystallization is predominantly observed in as-rolled specimens.Fracture morphology analysis reveals that a mixed fracture mechanism is prevalent in the as-homogenized specimen,whereas a ductile fracture mechanism is predominant in the as-rolled specimen.The processing maps indicate that the unstable region is reduced in the as-rolled specimens compared with that in the as-homogenized specimens.The optimal hot working windows for the as-homogenized and as-rolled specimens are determined as 410-440℃/0.14-1 s^(−1)and 380-400℃/0.05-0.29 s^(−1),respectively.
基金financial support from the National Key Research and Development Program of China(No.2016YFB0300900)the National Key Fundamental Research Project of China(No.2012CB619506-3)the National Natural Science Foundation of China(No.51171209)。
文摘Texture and grain structure evolution during annealing and their effects on tensile strength and anisotropy were studied using XRD,DSC,SEM,EBSD and TEM.The results indicate that elevated rolling temperatures reduce the f(g)_(max(Copper))/f(g)_(max(Brass))ratio,increase S-Brass fine bands,and promote S-dispersoid precipitation,leading to finer recrystallized grains.Dominant recrystallization textures transform from Goss+P to Goss and then to Goss+Cube with increasing rolling temperature.Annealing at 350℃shows four tensile strength response stages:fast softening I,rapid strengthening II,slow strengthening III,and slow softening IV.The transition from Stages I to II is driven by the formation of strong Goss and P textures,and Stage IV is linked to enhanced Cube texture.Plates with Goss+Cube textures and fine equiaxed grains exhibit the lowest YS/UTS ratio and minimal anisotropy.
