A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characteriz...A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.展开更多
The dense TiC Fe cermets were produced by self propagating high temperature synthesis and pseudo hot isostatic pressing(SHS/PHIP). The influence of Fe content on the combustion temperature, combustion velocity, densit...The dense TiC Fe cermets were produced by self propagating high temperature synthesis and pseudo hot isostatic pressing(SHS/PHIP). The influence of Fe content on the combustion temperature, combustion velocity, density and microstructure of products was studied. The composition and microstructure of the product were analyzed. The results showed that the cermet consists of quasi spherical TiC particles and Fe binder phases. A thin diffusion layer was found between Fe binder phase and TiC particle. In the range of 10%～20% Fe content, the combustion temperature and velocity decrease more slowly than the other contributions.展开更多
基金The financial support from the National Natural Science Foundation of China (20590361)the National Outstanding Young Scientists Foundation of China (20625620)
文摘A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.
文摘The dense TiC Fe cermets were produced by self propagating high temperature synthesis and pseudo hot isostatic pressing(SHS/PHIP). The influence of Fe content on the combustion temperature, combustion velocity, density and microstructure of products was studied. The composition and microstructure of the product were analyzed. The results showed that the cermet consists of quasi spherical TiC particles and Fe binder phases. A thin diffusion layer was found between Fe binder phase and TiC particle. In the range of 10%～20% Fe content, the combustion temperature and velocity decrease more slowly than the other contributions.
