As the environmental problems become increasingly serious,distributed electrical propulsion systems with higher aerodynamic efficiency and lower pollution emission have received extensive attention in recent years.The...As the environmental problems become increasingly serious,distributed electrical propulsion systems with higher aerodynamic efficiency and lower pollution emission have received extensive attention in recent years.The distributed electrical propulsion usually employs the new aero-propulsion integrated configuration.A simulation strategy for internal and external flow coupling based on the combination of lifting line theory and body force method is proposed.The lifting line theory and body force method as source term are embedded into the Navier-Stokes formulation.The lift and drag characteristics of the aero-propulsion coupling configuration are simulated.The results indicate that the coupling configuration has the most obvious lift augmentation at 12°angle of attack,which can provide an 11.11%increase in lift for the airfoil.At 0°angle of attack,the pressure difference on the lip parts provides the thrust component,which results in a lower drag coefficient.Additionally,the failure impact of a ducted fan at the middle or edge on aerodynamics is investigated.For the two failure conditions,the lift of the coupling configuration is decreased significantly by 27.85%and 26.14%respectively,and the lip thrust is decreased by 70.74%and 56.48%respectively.展开更多
The Distributed Propulsion Wing(DPW)presents prominent advantages in terms of energy conservation during flight,but the intense integration of propulsive internal flow with aerodynamic external flow brings significant...The Distributed Propulsion Wing(DPW)presents prominent advantages in terms of energy conservation during flight,but the intense integration of propulsive internal flow with aerodynamic external flow brings significant design challenges.To tackle this issue,this paper undertakes a comprehensive investigation of the aero-propulsive coupling performance of the DPW under both hovering and cruising conditions,and subsequently proposes a multi-level collaboration optimization design method based on the decomposition principle.Specifically,the complex 3D surfaces of DPW are systematically dissociated into simple 2D curves with inherent relationships for design.The decomposition is achieved based on the analysis results of the aero-propulsive coupling characteristics.And a DPW design case is conducted and subsequently analyzed in order to further validate the effectiveness and feasibility of the proposed design method.It is shown that a 115.75%drag reduction of DPW can be achieved at cruise under a specified thrust level.Furthermore,the DPW exhibits inherent characteristics of consistent lift-to-drag ratio with the thrust-drag balance constraint,regardless of variations in incoming flow velocity or total thrust.展开更多
Aiming to maximize the aerodynamic performance of the Distributed Electric Propulsion(DEP)aircraft,a hybrid design framework which focuses on the aerodynamic performance of the propeller/wing integration has been deve...Aiming to maximize the aerodynamic performance of the Distributed Electric Propulsion(DEP)aircraft,a hybrid design framework which focuses on the aerodynamic performance of the propeller/wing integration has been developed and validated numerically.Variable-fidelity modelling for propeller aerodynamics has been used to achieve computational efficiency with reasonable accuracy.By optimizing the aerodynamic loading distributions on the tractor propeller disk,the induced slipstream is redistributed into a form that is beneficial for the wing downstream,based on which the propeller blade geometry is generated through a rapid inversed design procedure.As compared with the Minimum Induced Loss(MIL)propeller at a specified thrust level,significant improvements of both the lift-to-drag ratio of the wing and the propeller/wing integrated aerodynamic efficiency is achieved,which shows great promise to deliver aerodynamic benefits for the wing within the propeller slipstream without any additional devices.展开更多
Distributed Electric Propulsion(DEP)aircraft use multiple electric motors to drive the propulsors,which gives potential benefits to aerodynamic-propulsion interaction.To investigate and quantify the aerodynamic-propul...Distributed Electric Propulsion(DEP)aircraft use multiple electric motors to drive the propulsors,which gives potential benefits to aerodynamic-propulsion interaction.To investigate and quantify the aerodynamic-propulsion interaction effect of the wing section,we built a DEP demonstrator with 24"high-lift"Electric Ducted Fans(EDFs)distributed along the wing’s trailing edge.This paper explores and compares the aero-propulsion coupling characteristics under various upstream speed,throttle,and EDF mounting surface deflection angles using a series of wind tunnel tests.We compare various lift-augmentation power conditions to the clean configuration without propulsion unit under the experiment condition of 15-25 m/s freestream flow and angles of attack from-4°to 16°.The comparison of computational results to the experimental results verifies the effectiveness of the computational fluid dynamic analysis method and the modeling method for the DEP configuration.The results show that the EDFs can produce significant lift increment and drag reduction simultaneously,which is accordant with the potential benefit of Boundary Layer Ingestion(BLI)at low airspeed.展开更多
Distributed electric propulsion(DEP)uses multiple propellers driven by motors distributed along the leading edge of the wing to produce beneficial aerodynamic interactions.However,the wing will be in the sliding flow ...Distributed electric propulsion(DEP)uses multiple propellers driven by motors distributed along the leading edge of the wing to produce beneficial aerodynamic interactions.However,the wing will be in the sliding flow of the propeller and the lift and drag characteristics of the wing will change accordingly.The performance of the propeller will also be affected by the wing in its rear.In this paper,combined with wind tunnel tests,the low Reynolds aerodynamic properties of multiple DEP structures are numerically simulated by solving the Reynolds averaged Navier-Stokes(RANS)equation of multiple reference frames(MRF)or slip grid technology.The results demonstrate that the lift and drag of DEP increase in all cases,with the magnitude depending on the angle of attack(AOA)and the relative positions of propellers and wing.When the AOA is less than 16°(stall AOA),the change of lift is not affected by it.By contrast,when the AOA is greater than 16°the L/D(lift-to-drag ratio)of the DEP system increases significantly.This is because the propeller slipstream delays laminar flow separation and increases the stall AOA.At the same time,the inflow and the downwash effect,which is generated on both sides of the rotating shaft,result in the actual AOA of the wing being greater than the free flow AOA with a fluctuation distribution of the lift coefficient along the span.Also,for the propeller in the DEP,the blocking effect of the wing and the vortex of the trailing edge of the wing result in a significant increase in thrust.展开更多
The inner rotors of distributed propulsion tilt-wing Unmanned Aerial Vehicles(UAVs)are often folded in the cruising state and deployed in vertical take-off and landing to cope with the huge difference in thrust requir...The inner rotors of distributed propulsion tilt-wing Unmanned Aerial Vehicles(UAVs)are often folded in the cruising state and deployed in vertical take-off and landing to cope with the huge difference in thrust requirements.However,the blades of the conventional rotor have poor conformality with the nacelle profile,which will greatly increase the drag of the UAV after folding.This paper proposes an integrated method for the design of rotor and nacelle considering geometric compatibility to reduce the drag of the folded rotor and nacelle,so as to further improve the aerodynamic efficiency in cruise while ensuring the rotor efficiency in the vertical flight mode.A geometric mapping model based on nacelle design parameters and rotor design parameters is established,and a parametric model and aerodynamic optimization model of the outer arc airfoil family are developed.In addition,a rotor performance analysis model and a neural network response surface model for nacelle drag prediction that meet the requirements of confidence level are established.Based on the oblique inflow blade element momentum theory method,numerical simulation method,and genetic algorithm,an integrated optimization framework of the design of the conformal rotor and nacelle is built.Then,a geometrically compatible integrated optimization for the rotor and nacelle is carried out with the objective of maximizing energy efficiency in the full mission profile.Finally,a conformal rotor and nacelle design solution is obtained,which satisfies geometric compatibility and thrust constraints while providing high thrust efficiency and low cruising drag.A comparison of the results of the integrated design and the conventional rotor optimization design shows that the drag of the conventional rotor is 3.45 times that of the conformal integrated design in the cruising state,which proves the effectiveness and necessity of the proposed method.展开更多
The efficient utilization of propeller slipstream energy is important for improving the ultra-short takeoff and landing capability of Distributed Electric Propulsion(DEP)aircraft.This paper presents a quasi-three-dime...The efficient utilization of propeller slipstream energy is important for improving the ultra-short takeoff and landing capability of Distributed Electric Propulsion(DEP)aircraft.This paper presents a quasi-three-dimensional(2.5D)high-lift wing design approach considering the three-dimensional(3D)effects of slipstream for DEP aircraft,aiming at maximizing the comprehensive lift enhancement benefit of the airframe-propulsion coupling unit.A high-precision and efficient momentum source method is adopted to simulate the slipstream effects,and the distributed propellers are replaced by a rectangular actuator disk to reduce the difficulty of grid generation and improve the grid quality.A detailed comparison of the 2.5D and 3D configurations based on the X-57 ModⅣis performed in terms of flow characteristics and computational cost to demonstrate the rationality of the above design approach.The optimization results of the high-lift wing of the X-57 ModⅣshow that the aerodynamic performance of the landing configuration is significantly improved,for instance,the lift coefficient increases by 0.094 at the angle of attack of 7°,and 0.097 at the angle of attack of 14°.This novel approach achieves efficient and effective design of high-lift wings under the influence of distributed slipstream,which has the potential to improve the design level of DEP aircraft.展开更多
The technology of electric propulsion aircraft(EPA)represents an important direction and an advanced stage in the development of aviation electrification.It is a key pathway for green development in aviation industry ...The technology of electric propulsion aircraft(EPA)represents an important direction and an advanced stage in the development of aviation electrification.It is a key pathway for green development in aviation industry and can significantly enhance the energy efficiency of aircraft propulsion system.Electric motor is the most critical electromechanical energy conversion component in an aircraft electric propulsion system(EPS).High-performance electric motors,power electronic converters and EPS control form the foundation of the EPA.This paper provides an overview of the characteristics of electric motors for EPA,analyzes the inverter topologies of EPSs,and reviews ongoing EPA projects.The article highlights the latest advancements in three types of motors:superconducting motors(SCMs),permanent magnet synchronous motors(PMSMs),and induction motors(IMs).It summarizes the control system architectures of current EPA initiatives and,building on this foundation,proposes future research directions for EPSs.These include cutting-edge areas such as high-performance motors and advanced manufacturing technologies,Ga N-or Si C-based inverter integration and innovation,electric propulsion control systems,and optimization of wiring systems.展开更多
Emissions produced by the aviation industry are currently a severe environmental threat;therefore,aviation agencies and governments have set emission targets and formulated plans to restrict emissions within the next ...Emissions produced by the aviation industry are currently a severe environmental threat;therefore,aviation agencies and governments have set emission targets and formulated plans to restrict emissions within the next decade.Hybrid aircraft technology is being considered to meet these targets.The importance of these technologies lies in their advancements in terms of aircraft life cycles and environmental benignity.Owing to these advancements,hybrid electric systems with more than one power source have become promising for the aviation industry,considering that the growth of air traffic is projected to double in the next decade.Hybrid technologies have given future hybrid fans and motor-fan engines potential as alternative power generators.Herein,Turboelectric Distributed Propulsion(TeDP)is discussed in terms of power distribution and power sources.The fundamentals of turbofan and turboshaft engines are presented along with their electricitygeneration mechanism.TeDP is discussed from a design viewpoint,with a detailed discussion of different types of hybrid electric and turboelectric systems.Examples of proposed TeDP aircraft models and numerical modelling tools used to simulate the performance of TeDP models are reviewed.Finally,innovative turboelectric systems in which electric power savers and mechanical gear changers have been discarded for weight optimisation are presented along with other prospective models,engines,approaches,and architectures.The findings of this review indicate the knowledge gaps in the field of numerical modelling for NASA’s TeDP and its capability to increase the efficiency by up to 24%with a 50%reduction in emissions relative to those of conventional gas turbines.展开更多
Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interac...Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.展开更多
In recent decades,the detrimental impact of aviation has grown into a serious problem for the aeronautical sector.Even while well established modern innovations like high bypass ratio engines and composite materials h...In recent decades,the detrimental impact of aviation has grown into a serious problem for the aeronautical sector.Even while well established modern innovations like high bypass ratio engines and composite materials have enhanced efficiency,there is still a growing need for more environmentally friendly alternatives.In this review,hydrogen-powered distributed propulsion aircraft are considered as an appealing means of reducing emissions and operating costs.In light of its high specific energy,liquid hydrogen is recognized as a major catalyst,requiring developments in lightweight,reusable cryogenic storage systems.The shift to hydrogen-powered aircraft with a fleet adoption rate of 40%by 2050 could offset 250 million tons of carbon dioxide,reducing aviation’s global carbon footprint by 12%.The blended-wing-body concept,offering aerodynamic and environmental benefits,is pointed out as an optimal configuration to integrate distributed propulsion together with boundary-layer-ingestion technologies.This article analyzes the state of the art in hydrogen technologies,blended-wing-body design challenges,and distributed propulsion systems.Furthermore,it evaluates the technological,financial,and regulatory hurdles,suggesting potential development paths to make hydrogen-powered aircraft viable in the future.展开更多
A type of distributed pump-jet propulsion system （DPJP） is developed with two or four specially designed pump-jet pods located around the axisymmetric underwater vehicle body symmetrically. The flow field is numeric...A type of distributed pump-jet propulsion system （DPJP） is developed with two or four specially designed pump-jet pods located around the axisymmetric underwater vehicle body symmetrically. The flow field is numerically simulated by solving the RANS equations with the finite volume method. The computational method is validated by comparing the calculated hull resistances of the SUBOFF AFF-3 model and the open water performance of a ducted propeller with experimental data. The hydrodynamic performances of the DPJP with different axial or radial positions and numbers of pump-jet pods are obtained to analyze the interactions between the hull and the pump-jet pods. It is shown in the calculated results that the decrease of the distance between the pods and the hull leads to an increase both in the efficiency of the pods and the thrust deduction factor due to the effect of the stern wake. And, a negative thrust deduction factor can be obtained by locating the DPJP at the parallel middle body near the aftbody of the vehicle to improve the hydrodynamic performance of the DPJP. Besides, the increase of the number of pods will cause a remarkable decrease of the total propulsive efficiency of the DPJP with the pods mounted on the stern planes, while a small decline of the total propulsive efficiency of the DPJP is observed with the pods mounted on the parallel middle body.展开更多
基金the funding support from the Taihang Laboratory,China(No.D2024-1-0201).
文摘As the environmental problems become increasingly serious,distributed electrical propulsion systems with higher aerodynamic efficiency and lower pollution emission have received extensive attention in recent years.The distributed electrical propulsion usually employs the new aero-propulsion integrated configuration.A simulation strategy for internal and external flow coupling based on the combination of lifting line theory and body force method is proposed.The lifting line theory and body force method as source term are embedded into the Navier-Stokes formulation.The lift and drag characteristics of the aero-propulsion coupling configuration are simulated.The results indicate that the coupling configuration has the most obvious lift augmentation at 12°angle of attack,which can provide an 11.11%increase in lift for the airfoil.At 0°angle of attack,the pressure difference on the lip parts provides the thrust component,which results in a lower drag coefficient.Additionally,the failure impact of a ducted fan at the middle or edge on aerodynamics is investigated.For the two failure conditions,the lift of the coupling configuration is decreased significantly by 27.85%and 26.14%respectively,and the lip thrust is decreased by 70.74%and 56.48%respectively.
基金co-supported by the Equipment Advance Research Project of China(No.50911040803)the National Defense Pre-research Foundation of China(No.2021-JCJQJJ-0805)the Aeronautical Science Foundation of China(No.2024Z006053001)。
文摘The Distributed Propulsion Wing(DPW)presents prominent advantages in terms of energy conservation during flight,but the intense integration of propulsive internal flow with aerodynamic external flow brings significant design challenges.To tackle this issue,this paper undertakes a comprehensive investigation of the aero-propulsive coupling performance of the DPW under both hovering and cruising conditions,and subsequently proposes a multi-level collaboration optimization design method based on the decomposition principle.Specifically,the complex 3D surfaces of DPW are systematically dissociated into simple 2D curves with inherent relationships for design.The decomposition is achieved based on the analysis results of the aero-propulsive coupling characteristics.And a DPW design case is conducted and subsequently analyzed in order to further validate the effectiveness and feasibility of the proposed design method.It is shown that a 115.75%drag reduction of DPW can be achieved at cruise under a specified thrust level.Furthermore,the DPW exhibits inherent characteristics of consistent lift-to-drag ratio with the thrust-drag balance constraint,regardless of variations in incoming flow velocity or total thrust.
基金supported by the Key Research and Development Program of Shaanxi Province of China(No.2018ZDCXL-GY-03-04)。
文摘Aiming to maximize the aerodynamic performance of the Distributed Electric Propulsion(DEP)aircraft,a hybrid design framework which focuses on the aerodynamic performance of the propeller/wing integration has been developed and validated numerically.Variable-fidelity modelling for propeller aerodynamics has been used to achieve computational efficiency with reasonable accuracy.By optimizing the aerodynamic loading distributions on the tractor propeller disk,the induced slipstream is redistributed into a form that is beneficial for the wing downstream,based on which the propeller blade geometry is generated through a rapid inversed design procedure.As compared with the Minimum Induced Loss(MIL)propeller at a specified thrust level,significant improvements of both the lift-to-drag ratio of the wing and the propeller/wing integrated aerodynamic efficiency is achieved,which shows great promise to deliver aerodynamic benefits for the wing within the propeller slipstream without any additional devices.
基金supported by the National Natural Science Foundation of China(No.51877178)。
文摘Distributed Electric Propulsion(DEP)aircraft use multiple electric motors to drive the propulsors,which gives potential benefits to aerodynamic-propulsion interaction.To investigate and quantify the aerodynamic-propulsion interaction effect of the wing section,we built a DEP demonstrator with 24"high-lift"Electric Ducted Fans(EDFs)distributed along the wing’s trailing edge.This paper explores and compares the aero-propulsion coupling characteristics under various upstream speed,throttle,and EDF mounting surface deflection angles using a series of wind tunnel tests.We compare various lift-augmentation power conditions to the clean configuration without propulsion unit under the experiment condition of 15-25 m/s freestream flow and angles of attack from-4°to 16°.The comparison of computational results to the experimental results verifies the effectiveness of the computational fluid dynamic analysis method and the modeling method for the DEP configuration.The results show that the EDFs can produce significant lift increment and drag reduction simultaneously,which is accordant with the potential benefit of Boundary Layer Ingestion(BLI)at low airspeed.
基金This work is supported by the National Natural Science Foundation of China(No.51505087)the Fujian Provincial Industrial Robot Basic Components Technology Research and Development Center(No.2014H2004),China.
文摘Distributed electric propulsion(DEP)uses multiple propellers driven by motors distributed along the leading edge of the wing to produce beneficial aerodynamic interactions.However,the wing will be in the sliding flow of the propeller and the lift and drag characteristics of the wing will change accordingly.The performance of the propeller will also be affected by the wing in its rear.In this paper,combined with wind tunnel tests,the low Reynolds aerodynamic properties of multiple DEP structures are numerically simulated by solving the Reynolds averaged Navier-Stokes(RANS)equation of multiple reference frames(MRF)or slip grid technology.The results demonstrate that the lift and drag of DEP increase in all cases,with the magnitude depending on the angle of attack(AOA)and the relative positions of propellers and wing.When the AOA is less than 16°(stall AOA),the change of lift is not affected by it.By contrast,when the AOA is greater than 16°the L/D(lift-to-drag ratio)of the DEP system increases significantly.This is because the propeller slipstream delays laminar flow separation and increases the stall AOA.At the same time,the inflow and the downwash effect,which is generated on both sides of the rotating shaft,result in the actual AOA of the wing being greater than the free flow AOA with a fluctuation distribution of the lift coefficient along the span.Also,for the propeller in the DEP,the blocking effect of the wing and the vortex of the trailing edge of the wing result in a significant increase in thrust.
基金the Fundamental Research Funds for the Central Universities(No.56XCA2205402).
文摘The inner rotors of distributed propulsion tilt-wing Unmanned Aerial Vehicles(UAVs)are often folded in the cruising state and deployed in vertical take-off and landing to cope with the huge difference in thrust requirements.However,the blades of the conventional rotor have poor conformality with the nacelle profile,which will greatly increase the drag of the UAV after folding.This paper proposes an integrated method for the design of rotor and nacelle considering geometric compatibility to reduce the drag of the folded rotor and nacelle,so as to further improve the aerodynamic efficiency in cruise while ensuring the rotor efficiency in the vertical flight mode.A geometric mapping model based on nacelle design parameters and rotor design parameters is established,and a parametric model and aerodynamic optimization model of the outer arc airfoil family are developed.In addition,a rotor performance analysis model and a neural network response surface model for nacelle drag prediction that meet the requirements of confidence level are established.Based on the oblique inflow blade element momentum theory method,numerical simulation method,and genetic algorithm,an integrated optimization framework of the design of the conformal rotor and nacelle is built.Then,a geometrically compatible integrated optimization for the rotor and nacelle is carried out with the objective of maximizing energy efficiency in the full mission profile.Finally,a conformal rotor and nacelle design solution is obtained,which satisfies geometric compatibility and thrust constraints while providing high thrust efficiency and low cruising drag.A comparison of the results of the integrated design and the conventional rotor optimization design shows that the drag of the conventional rotor is 3.45 times that of the conformal integrated design in the cruising state,which proves the effectiveness and necessity of the proposed method.
文摘The efficient utilization of propeller slipstream energy is important for improving the ultra-short takeoff and landing capability of Distributed Electric Propulsion(DEP)aircraft.This paper presents a quasi-three-dimensional(2.5D)high-lift wing design approach considering the three-dimensional(3D)effects of slipstream for DEP aircraft,aiming at maximizing the comprehensive lift enhancement benefit of the airframe-propulsion coupling unit.A high-precision and efficient momentum source method is adopted to simulate the slipstream effects,and the distributed propellers are replaced by a rectangular actuator disk to reduce the difficulty of grid generation and improve the grid quality.A detailed comparison of the 2.5D and 3D configurations based on the X-57 ModⅣis performed in terms of flow characteristics and computational cost to demonstrate the rationality of the above design approach.The optimization results of the high-lift wing of the X-57 ModⅣshow that the aerodynamic performance of the landing configuration is significantly improved,for instance,the lift coefficient increases by 0.094 at the angle of attack of 7°,and 0.097 at the angle of attack of 14°.This novel approach achieves efficient and effective design of high-lift wings under the influence of distributed slipstream,which has the potential to improve the design level of DEP aircraft.
基金supported by the National Nature Science Foundation of China(Grant No.52302507)。
文摘The technology of electric propulsion aircraft(EPA)represents an important direction and an advanced stage in the development of aviation electrification.It is a key pathway for green development in aviation industry and can significantly enhance the energy efficiency of aircraft propulsion system.Electric motor is the most critical electromechanical energy conversion component in an aircraft electric propulsion system(EPS).High-performance electric motors,power electronic converters and EPS control form the foundation of the EPA.This paper provides an overview of the characteristics of electric motors for EPA,analyzes the inverter topologies of EPSs,and reviews ongoing EPA projects.The article highlights the latest advancements in three types of motors:superconducting motors(SCMs),permanent magnet synchronous motors(PMSMs),and induction motors(IMs).It summarizes the control system architectures of current EPA initiatives and,building on this foundation,proposes future research directions for EPSs.These include cutting-edge areas such as high-performance motors and advanced manufacturing technologies,Ga N-or Si C-based inverter integration and innovation,electric propulsion control systems,and optimization of wiring systems.
文摘Emissions produced by the aviation industry are currently a severe environmental threat;therefore,aviation agencies and governments have set emission targets and formulated plans to restrict emissions within the next decade.Hybrid aircraft technology is being considered to meet these targets.The importance of these technologies lies in their advancements in terms of aircraft life cycles and environmental benignity.Owing to these advancements,hybrid electric systems with more than one power source have become promising for the aviation industry,considering that the growth of air traffic is projected to double in the next decade.Hybrid technologies have given future hybrid fans and motor-fan engines potential as alternative power generators.Herein,Turboelectric Distributed Propulsion(TeDP)is discussed in terms of power distribution and power sources.The fundamentals of turbofan and turboshaft engines are presented along with their electricitygeneration mechanism.TeDP is discussed from a design viewpoint,with a detailed discussion of different types of hybrid electric and turboelectric systems.Examples of proposed TeDP aircraft models and numerical modelling tools used to simulate the performance of TeDP models are reviewed.Finally,innovative turboelectric systems in which electric power savers and mechanical gear changers have been discarded for weight optimisation are presented along with other prospective models,engines,approaches,and architectures.The findings of this review indicate the knowledge gaps in the field of numerical modelling for NASA’s TeDP and its capability to increase the efficiency by up to 24%with a 50%reduction in emissions relative to those of conventional gas turbines.
基金National Key Basic Research Special Foundation of China
文摘Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.
文摘In recent decades,the detrimental impact of aviation has grown into a serious problem for the aeronautical sector.Even while well established modern innovations like high bypass ratio engines and composite materials have enhanced efficiency,there is still a growing need for more environmentally friendly alternatives.In this review,hydrogen-powered distributed propulsion aircraft are considered as an appealing means of reducing emissions and operating costs.In light of its high specific energy,liquid hydrogen is recognized as a major catalyst,requiring developments in lightweight,reusable cryogenic storage systems.The shift to hydrogen-powered aircraft with a fleet adoption rate of 40%by 2050 could offset 250 million tons of carbon dioxide,reducing aviation’s global carbon footprint by 12%.The blended-wing-body concept,offering aerodynamic and environmental benefits,is pointed out as an optimal configuration to integrate distributed propulsion together with boundary-layer-ingestion technologies.This article analyzes the state of the art in hydrogen technologies,blended-wing-body design challenges,and distributed propulsion systems.Furthermore,it evaluates the technological,financial,and regulatory hurdles,suggesting potential development paths to make hydrogen-powered aircraft viable in the future.
文摘A type of distributed pump-jet propulsion system （DPJP） is developed with two or four specially designed pump-jet pods located around the axisymmetric underwater vehicle body symmetrically. The flow field is numerically simulated by solving the RANS equations with the finite volume method. The computational method is validated by comparing the calculated hull resistances of the SUBOFF AFF-3 model and the open water performance of a ducted propeller with experimental data. The hydrodynamic performances of the DPJP with different axial or radial positions and numbers of pump-jet pods are obtained to analyze the interactions between the hull and the pump-jet pods. It is shown in the calculated results that the decrease of the distance between the pods and the hull leads to an increase both in the efficiency of the pods and the thrust deduction factor due to the effect of the stern wake. And, a negative thrust deduction factor can be obtained by locating the DPJP at the parallel middle body near the aftbody of the vehicle to improve the hydrodynamic performance of the DPJP. Besides, the increase of the number of pods will cause a remarkable decrease of the total propulsive efficiency of the DPJP with the pods mounted on the stern planes, while a small decline of the total propulsive efficiency of the DPJP is observed with the pods mounted on the parallel middle body.
