This paper presents a new method to estimate the height of the atmospheric boundary layer(ABL) by using COSMIC radio occultation bending angle(BA) data. Using the numerical differentiation method combined with the reg...This paper presents a new method to estimate the height of the atmospheric boundary layer(ABL) by using COSMIC radio occultation bending angle(BA) data. Using the numerical differentiation method combined with the regularization technique, the first derivative of BA profiles is retrieved, and the height at which the first derivative of BA has the global minimum is defined to be the ABL height. To reflect the reliability of estimated ABL heights, the sharpness parameter is introduced, according to the relative minimum of the BA derivative. Then, it is applied to four months of COSMIC BA data(January, April, July, and October in 2008), and the ABL heights estimated are compared with two kinds of ABL heights from COSMIC products and with the heights determined by the finite difference method upon the refractivity data. For sharp ABL tops(large sharpness parameters), there is little difference between the ABL heights determined by different methods, i.e.,the uncertainties are small; whereas, for non-sharp ABL tops(small sharpness parameters), big differences exist in the ABL heights obtained by different methods, which means large uncertainties for different methods. In addition, the new method can detect thin ABLs and provide a reference ABL height in the cases eliminated by other methods. Thus, the application of the numerical differentiation method combined with the regularization technique to COSMIC BA data is an appropriate choice and has further application value.展开更多
This paper presents a novel element differential method for modeling cracks in piezoelectric materials,aiming to simulate fracture behaviors and predict the fracture parameter known as the J-integral accurately.The me...This paper presents a novel element differential method for modeling cracks in piezoelectric materials,aiming to simulate fracture behaviors and predict the fracture parameter known as the J-integral accurately.The method leverages an efficient collocation technique to satisfy traction and electric charge equilibrium on the crack surface,aligning internal nodes with piezoelectric governing equations without needing integration or variational principles.It combines the strengths of the strong form collocation and finite element methods.The J-integral is derived analytically using the equivalent domain integral method,employing Green's formula and Gauss's divergence theorem to transform line integrals into area integrals for solving two-dimensional piezoelectric material problems.The accuracy of the method is validated through comparison with three typical examples,and it offers fracture prevention strategies for engineering piezoelectric structures under different electrical loading patterns.展开更多
This paper investigates the active traveling wave vibration control of an elastic supported rotating porous aluminium conical shell(CS)under impact loading.Piezoelectric smart materials in the form of micro fiber comp...This paper investigates the active traveling wave vibration control of an elastic supported rotating porous aluminium conical shell(CS)under impact loading.Piezoelectric smart materials in the form of micro fiber composites(MFCs)are used as actuators and sensors.To this end,a metal pore truncated CS with MFCs attached to its surface is considered.Adding artificial virtual springs at two edges of the truncated CS achieves various elastic supported boundaries by changing the spring stiffness.Based on the first-order shear deformation theory(FSDT),minimum energy principle,and artificial virtual spring technology,the theoretical formulations considering the electromechanical coupling are derived.The comparison of the natural frequency of the present results with the natural frequencies reported in previous literature evaluates the accuracy of the present approach.To study the vibration control,the integral quadrature method in conjunction with the differential quadrature approximation in the length direction is used to discretize the partial differential dynamical system to form a set of ordinary differential equations.With the aid of the velocity negative feedback method,both the time history and the input control voltage on the actuator are demonstrated to present the effects of velocity feedback gain,pore distribution type,semi-vertex angle,impact loading,and rotational angular velocity on the traveling wave vibration control.展开更多
Mesenchymal stem cells(MSCs)have received significant attention in recent years due to their large potential for cell therapy.Indeed,they secrete a wide variety of immunomodulatory factors of interest for the treatmen...Mesenchymal stem cells(MSCs)have received significant attention in recent years due to their large potential for cell therapy.Indeed,they secrete a wide variety of immunomodulatory factors of interest for the treatment of immune-related disorders and inflammatory diseases.MSCs can be extracted from multiple tissues of the human body.However,several factors may restrict their use for clinical applications:the requirement of invasive procedures for their isolation,their limited numbers,and their heterogeneity according to the tissue of origin or donor.In addition,MSCs often present early signs of replicative senescence limiting their expansion in vitro,and their therapeutic capacity in vivo.Due to the clinical potential of MSCs,a considerable number of methods to differentiate induced pluripotent stem cells(iPSCs)into MSCs have emerged.iPSCs represent a new reliable,unlimited source to generate MSCs(MSCs derived from iPSC,iMSCs)from homogeneous and well-characterized cell lines,which would relieve many of the above mentioned technical and biological limitations.Additionally,the use of iPSCs prevents some of the ethical concerns surrounding the use of human embryonic stem cells.In this review,we analyze the main current protocols used to differentiate human iPSCs into MSCs,which we classify into five different categories:MSC Switch,Embryoid Body Formation,Specific Differentiation,Pathway Inhibitor,and Platelet Lysate.We also evaluate common and method-specific culture components and provide a list of positive and negative markers for MSC characterization.Further guidance on material requirements to produce iMSCs with these methods and on the phenotypic features of the iMSCs obtained is added.The information may help researchers identify protocol options to design and/or refine standardized procedures for large-scale production of iMSCs fitting clinical demands.展开更多
The static behavior of piezoelectric circular spherical shallow shells under both electrical and mechanical loads is studied by using the differential quadrature element method (DQEM). Geometrical nonlinearity effect ...The static behavior of piezoelectric circular spherical shallow shells under both electrical and mechanical loads is studied by using the differential quadrature element method (DQEM). Geometrical nonlinearity effect is considered. Detailed formulations and procedures are given for the first time. Several examples are analyzed and accurate results are obtained by the DQEM. Based on the results in this paper, one may conclude that the DQEM is a useful tool for obtaining solutions of structural elements. It can be seen that the shell shape may be theore tically controlled and snap through may occur when the applied voltage reaches a critical value even without mechanical load for certain geometric configurations.展开更多
The consistency of the cell has a significant impact on battery capacity,endurance,overall performance,safety,and service life extension.However,it is challenging to identify cells with high consistency and no loss of...The consistency of the cell has a significant impact on battery capacity,endurance,overall performance,safety,and service life extension.However,it is challenging to identify cells with high consistency and no loss of battery energy.This paper presents a cell screening algorithm that integrates genetic and numerical differentiation techniques.Initially,a mathematical model for battery consistency is established,and a multi-step charging strategy is proposed to satisfy the demands of fast charging technology.Subsequently,the genetic algorithm simulates biological evolution to efficiently search for superior cell combinations within a short time while evaluating capacity,voltage consistency,and charge/discharge efficiency.Finally,through experimental validation and comparative analysis with similar algorithms,our proposed method demonstrates notable advantages in terms of both search efficiency and performance.展开更多
It is a new attempt to extend the differential quadrature method(DQM) to stability analysis of the straight and curved centerlinepipes conveying fluid. Emphasis is placed on the study of theinfluences of several param...It is a new attempt to extend the differential quadrature method(DQM) to stability analysis of the straight and curved centerlinepipes conveying fluid. Emphasis is placed on the study of theinfluences of several parameters on the critical flow velocity.Compared to other methods, this method can more easily deal with thepipe with spring support at its boundaries and asks for much lesscomputing effort while giving ac- ceptable precision in the numericalresults.展开更多
This article presents a numerical solution for the flow of a Newtonian fluid over an impermeable stretching sheet embedded in a porous medium with the power law surface velocity and variable thickness in the presence ...This article presents a numerical solution for the flow of a Newtonian fluid over an impermeable stretching sheet embedded in a porous medium with the power law surface velocity and variable thickness in the presence of thermal radiation. The flow is caused by non-linear stretching of a sheet. Thermal conductivity of the fluid is assumed to vary linearly with temperature. The governing partial differential equations （PDEs） are transformed into a system of coupled non-linear ordinary differential equations （ODEs） with appropriate boundary conditions for various physical parameters. The remaining system of ODEs is solved numerically using a differential transformation method （DTM）. The effects of the porous parameter, the wall thickness parameter, the radiation parameter, the thermal conductivity parameter, and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction and the Nusselt numbers are presented. Comparison of the obtained numerical results is made with previously published results in some special cases, with good agreement. The results obtained in this paper confirm the idea that DTM is a powerful mathematical tool and can be applied to a large class of linear and non-linear problems in different fields of science and engineering.展开更多
The authors give the solution to the problem of one-dimensional conso l idation of double-layered ground with the use of the differential quadrature me t hod. Case studies showed that the computational results for por...The authors give the solution to the problem of one-dimensional conso l idation of double-layered ground with the use of the differential quadrature me t hod. Case studies showed that the computational results for pore-water pressure in soil layer agreed with those of analytical solution; and that in the computat ional results for the interface of soil layer also agreed with those of the anal ytical solution except for the small discrepancies during shortly after the star t of computation. The advantages of the solution presented in this paper are tha t compared with the analytical solution, it avoids the cumbersome work in solvin g the transcendental equation for eigenvalues, and in the case of the Laplace transform s olution, it can resolve the precision problem in the numerical solution of long time inverse Laplace transform. Because of the matrix form of the solution in th is paper, it is convenient for formulating computational program for engineering practice. The formulas for calculating double-layered ground consolidation may be easily extended to the case of multi-layered soils.展开更多
Unconditionally stable higher-order accurate time step integration algorithms based on the differential quadrature method (DQM) for second-order initial value problems were applied and the quadrature rules of DQM, com...Unconditionally stable higher-order accurate time step integration algorithms based on the differential quadrature method (DQM) for second-order initial value problems were applied and the quadrature rules of DQM, computing of the weighting coefficients and choices of sampling grid points were discussed. Some numerical examples dealing with the heat transfer problem, the second-order differential equation of imposed vibration of linear single-degree-of-freedom systems and double-degree-of-freedom systems, the nonlinear move differential equation and a beam forced by a changing load were computed, respectively. The results indicated that the algorithm can produce highly accurate solutions with minimal time consumption, and that the system total energy can remain conservative in the numerical computation.展开更多
This paper presents a combined application of the finite element method （FEM） and the differential quadrature method （DQM） to vibration and buckling problems of rectangular plates. The proposed scheme combines the...This paper presents a combined application of the finite element method （FEM） and the differential quadrature method （DQM） to vibration and buckling problems of rectangular plates. The proposed scheme combines the geometry flexibility of the FEM and the high accuracy and efficiency of the DQM. The accuracy of the present method is demonstrated by comparing the obtained results with those available in the literature. It is shown that highly accurate results can be obtained by using a small number of finite elements and DQM sample points. The proposed method is suitable for the problems considered due to its simplicity and potential for further development.展开更多
The character of the deformation zone on pair cross rolls is different from that of the regular 4-high mill. Considering comprehensive influences of normal stress and shear stress in rolling direction, width direction...The character of the deformation zone on pair cross rolls is different from that of the regular 4-high mill. Considering comprehensive influences of normal stress and shear stress in rolling direction, width direction and thickness direction, the rolling force calculation model of the PC （pair crossed） hot strip mill is built. Taking the entry stress and the exit stress of strip as the boundary conditions, the longitudinal and transverse distribution of rolling force is worked out by the differential method. Then the total rolling force is calculated, and calculated results are verified by experimental data.展开更多
A differential quadrature (DQ) method for orthotropic plates was proposed based on Reddy' s theory of plates with the effects of the higher-order transverse shear deformations. Wang-Bert's DQ approach was also...A differential quadrature (DQ) method for orthotropic plates was proposed based on Reddy' s theory of plates with the effects of the higher-order transverse shear deformations. Wang-Bert's DQ approach was also further extended to handle the boundary conditions of plates. The computational convergence was studied, and the numerical results were obtained for different grid spacings and compared with the existing results. The results show that the DQ method is fairly reliable and effective.展开更多
In this study, the effects of magnetic field and nanoparticle on the Jeffery- Hamel flow are studied using a powerful analytical method called the Adomian decomposition method （ADM）. The traditional Navier-Stokes eq...In this study, the effects of magnetic field and nanoparticle on the Jeffery- Hamel flow are studied using a powerful analytical method called the Adomian decomposition method （ADM）. The traditional Navier-Stokes equation of fluid mechanics and Maxwell＇s electromagnetism governing equations are reduced to nonlinear ordinary differential equations to model the problem. The obtained results are well agreed with that of the Runge-Kutta method. The present plots confirm that the method has high accuracy for different a, Ha, and Re numbers. The flow field inside the divergent channel is studied for various values of Hartmann ：number and angle of channel. The effect of nanoparticle volume fraction in the absence of magnetic field is investigated.展开更多
In this paper,we study the approximate solutions for some of nonlinear Biomathematics models via the e-epidemic SI1I2R model characterizing the spread of viruses in a computer network and SIR childhood disease model.T...In this paper,we study the approximate solutions for some of nonlinear Biomathematics models via the e-epidemic SI1I2R model characterizing the spread of viruses in a computer network and SIR childhood disease model.The reduced differential transforms method(RDTM)is one of the interesting methods for finding the approximate solutions for nonlinear problems.We apply the RDTM to discuss the analytic approximate solutions to the SI1I2R model for the spread of virus HCV-subtype and SIR childhood disease model.We discuss the numerical results at some special values of parameters in the approximate solutions.We use the computer software package such as Mathematical to find more iteration when calculating the approximate solutions.Graphical results and discussed quantitatively are presented to illustrate behavior of the obtained approximate solutions.展开更多
A differential geometrical method is for the first time used to calculate the effective moduli of a two-phase elastic composite materials with imperfect interface which the inclusions are assumed to be ellipsoidal of ...A differential geometrical method is for the first time used to calculate the effective moduli of a two-phase elastic composite materials with imperfect interface which the inclusions are assumed to be ellipsoidal of revolutions. All of the interface integral items participating in forming the potential and complementary energy functionals of the composite materials are expressed in terms of intrinsic quantities of the ellipsoidal of revolutions. Based on this, the upper and the lower bound for the effective elastic moduli of the composite materials with inclusions described above have been derived. Under three limiting conditions of sphere, disk and needle shaped inclusions, the results of this paper will return to the bounds obtained by Hashin([6]) (1992).展开更多
This paper aims to solve the resonance failure probability and develop an effective method to estimate the effects of variables and failure modes on failure probability of axially functionally graded material(FGM)pipe...This paper aims to solve the resonance failure probability and develop an effective method to estimate the effects of variables and failure modes on failure probability of axially functionally graded material(FGM)pipe conveying fluid.Correspondingly,the natural frequency of axially FGM pipes conveying fluid is calculated using the differential quadrature method(DQM).A variable sensitivity analysis(VSA)is introduced to measure the effect of each random variable,and a mode sensitivity analysis(MSA)is introduced to acquire the importance ranking of failure modes.Then,an active learning Kriging(ALK)method is established to calculate the resonance failure probability and sensitivity indices,which greatly improves the application of resonance reliability analysis for pipelines in engineering practice.Based on the resonance reliability analysis method,the effects of fluid velocity,volume fraction and fluid density of axially FGM pipe conveying fluid on resonance reliability are analyzed.The results demonstrate that the proposed method has great performance in the anti-resonance analysis of pipes conveying fluid.展开更多
The generalized differential quadrature method （GDQM） is employed to con- sider the free vibration and critical speed of moderately thick rotating laminated compos- ite conical shells with different boundary conditi...The generalized differential quadrature method （GDQM） is employed to con- sider the free vibration and critical speed of moderately thick rotating laminated compos- ite conical shells with different boundary conditions developed from the first-order shear deformation theory （FSDT）. The equations of motion are obtained applying Hamilton＇s concept, which contain the influence of the centrifugal force, the Coriolis acceleration, and the preliminary hoop stress. In addition, the axial load is applied to the conical shell as a ratio of the global critical buckling load. The governing partial differential equations are given in the expressions of five components of displacement related to the points ly- ing on the reference surface of the shell. Afterward, the governing differential equations are converted into a group of algebraic equations by using the GDQM. The outcomes are achieved considering the effects of stacking sequences, thickness of the shell, rotating velocities, half-vertex cone angle, and boundary conditions. Furthermore, the outcomes indicate that the rate of the convergence of frequencies is swift, and the numerical tech- nique is superior stable. Three comparisons between the selected outcomes and those of other research are accomplished, and excellent agreement is achieved.展开更多
The traditional differential quadrature method was improved by using theupwind difference scheme for the convective terms to solve the coupled two-dimensionalincompressible Navier-stokes equations and heat equation. T...The traditional differential quadrature method was improved by using theupwind difference scheme for the convective terms to solve the coupled two-dimensionalincompressible Navier-stokes equations and heat equation. The new method was compared with theconventional differential quadrature method in the aspects of convergence and accuracy. The resultsshow that the new method is more accurate, and has better convergence than the conventionaldifferential quadrature method for numerically computing the steady-state solution.展开更多
The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elas...The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elasticity theories using the differential quadrature method （DQM） is presented. Main advantages of the MCST over the classical theory （CT） are the inclusion of the asymmetric couple stress tensor and the consideration of only one material length scale parameter. Based on the nonlinear von Karman assumption, the governing equations of equilibrium for the micro-classical plate consid- ering midplane displacements are derived based on the minimum principle of potential energy. Using the DQM, the biaxial and shear critical buckling loads of the micro-plate for various boundary conditions are obtained. Accuracy of the obtained results is validated by comparing the solutions with those reported in the literature. A parametric study is conducted to show the effects of the aspect ratio, the side-to-thickness ratio, Eringen＇s nonlocal parameter, the material length scale parameter, Young＇s modulus of the surface layer, the surface residual stress, the polymer matrix coefficients, and various boundary conditions on the dimensionless uniaxial, biaxial, and shear critical buckling loads. The results indicate that the critical buckling loads are strongly sensitive to Eringen＇s nonlocal parameter, the material length scale parameter, and the surface residual stress effects, while the effect of Young＇s modulus of the surface layer on the critical buckling load is negligible. Also, considering the size dependent effect causes the increase in the stiffness of the orthotropic micro-plate. The results show that the critical biaxial buckling load increases with an increase in G12/E2 and vice versa for E1/E2. It is shown that the nonlinear biaxial buckling ratio decreases as the aspect ratio increases and vice versa for the buckling amplitude. Because of the most lightweight micro-composite materials with high strength/weight and stiffness/weight ratios, it is anticipated that the results of the present work are useful in experimental characterization of the mechanical properties of micro-composite plates in the aircraft industry and other engineering applications.展开更多
基金supported by the National Natural Science Foundation of China (Grant No. 41475021)
文摘This paper presents a new method to estimate the height of the atmospheric boundary layer(ABL) by using COSMIC radio occultation bending angle(BA) data. Using the numerical differentiation method combined with the regularization technique, the first derivative of BA profiles is retrieved, and the height at which the first derivative of BA has the global minimum is defined to be the ABL height. To reflect the reliability of estimated ABL heights, the sharpness parameter is introduced, according to the relative minimum of the BA derivative. Then, it is applied to four months of COSMIC BA data(January, April, July, and October in 2008), and the ABL heights estimated are compared with two kinds of ABL heights from COSMIC products and with the heights determined by the finite difference method upon the refractivity data. For sharp ABL tops(large sharpness parameters), there is little difference between the ABL heights determined by different methods, i.e.,the uncertainties are small; whereas, for non-sharp ABL tops(small sharpness parameters), big differences exist in the ABL heights obtained by different methods, which means large uncertainties for different methods. In addition, the new method can detect thin ABLs and provide a reference ABL height in the cases eliminated by other methods. Thus, the application of the numerical differentiation method combined with the regularization technique to COSMIC BA data is an appropriate choice and has further application value.
基金Financial support of this work by the Technology Development program of China(Grant No.2022204B003)National Natural Science Foundation of China(12272083 and 12172078)the Fundamental Research Funds for the Central Universities(DUT24YJ136)is gratefully acknowledged.
文摘This paper presents a novel element differential method for modeling cracks in piezoelectric materials,aiming to simulate fracture behaviors and predict the fracture parameter known as the J-integral accurately.The method leverages an efficient collocation technique to satisfy traction and electric charge equilibrium on the crack surface,aligning internal nodes with piezoelectric governing equations without needing integration or variational principles.It combines the strengths of the strong form collocation and finite element methods.The J-integral is derived analytically using the equivalent domain integral method,employing Green's formula and Gauss's divergence theorem to transform line integrals into area integrals for solving two-dimensional piezoelectric material problems.The accuracy of the method is validated through comparison with three typical examples,and it offers fracture prevention strategies for engineering piezoelectric structures under different electrical loading patterns.
基金Supported by the National Natural Science Foundation of China(Nos.12272056 and 11832002)。
文摘This paper investigates the active traveling wave vibration control of an elastic supported rotating porous aluminium conical shell(CS)under impact loading.Piezoelectric smart materials in the form of micro fiber composites(MFCs)are used as actuators and sensors.To this end,a metal pore truncated CS with MFCs attached to its surface is considered.Adding artificial virtual springs at two edges of the truncated CS achieves various elastic supported boundaries by changing the spring stiffness.Based on the first-order shear deformation theory(FSDT),minimum energy principle,and artificial virtual spring technology,the theoretical formulations considering the electromechanical coupling are derived.The comparison of the natural frequency of the present results with the natural frequencies reported in previous literature evaluates the accuracy of the present approach.To study the vibration control,the integral quadrature method in conjunction with the differential quadrature approximation in the length direction is used to discretize the partial differential dynamical system to form a set of ordinary differential equations.With the aid of the velocity negative feedback method,both the time history and the input control voltage on the actuator are demonstrated to present the effects of velocity feedback gain,pore distribution type,semi-vertex angle,impact loading,and rotational angular velocity on the traveling wave vibration control.
文摘Mesenchymal stem cells(MSCs)have received significant attention in recent years due to their large potential for cell therapy.Indeed,they secrete a wide variety of immunomodulatory factors of interest for the treatment of immune-related disorders and inflammatory diseases.MSCs can be extracted from multiple tissues of the human body.However,several factors may restrict their use for clinical applications:the requirement of invasive procedures for their isolation,their limited numbers,and their heterogeneity according to the tissue of origin or donor.In addition,MSCs often present early signs of replicative senescence limiting their expansion in vitro,and their therapeutic capacity in vivo.Due to the clinical potential of MSCs,a considerable number of methods to differentiate induced pluripotent stem cells(iPSCs)into MSCs have emerged.iPSCs represent a new reliable,unlimited source to generate MSCs(MSCs derived from iPSC,iMSCs)from homogeneous and well-characterized cell lines,which would relieve many of the above mentioned technical and biological limitations.Additionally,the use of iPSCs prevents some of the ethical concerns surrounding the use of human embryonic stem cells.In this review,we analyze the main current protocols used to differentiate human iPSCs into MSCs,which we classify into five different categories:MSC Switch,Embryoid Body Formation,Specific Differentiation,Pathway Inhibitor,and Platelet Lysate.We also evaluate common and method-specific culture components and provide a list of positive and negative markers for MSC characterization.Further guidance on material requirements to produce iMSCs with these methods and on the phenotypic features of the iMSCs obtained is added.The information may help researchers identify protocol options to design and/or refine standardized procedures for large-scale production of iMSCs fitting clinical demands.
文摘The static behavior of piezoelectric circular spherical shallow shells under both electrical and mechanical loads is studied by using the differential quadrature element method (DQEM). Geometrical nonlinearity effect is considered. Detailed formulations and procedures are given for the first time. Several examples are analyzed and accurate results are obtained by the DQEM. Based on the results in this paper, one may conclude that the DQEM is a useful tool for obtaining solutions of structural elements. It can be seen that the shell shape may be theore tically controlled and snap through may occur when the applied voltage reaches a critical value even without mechanical load for certain geometric configurations.
文摘The consistency of the cell has a significant impact on battery capacity,endurance,overall performance,safety,and service life extension.However,it is challenging to identify cells with high consistency and no loss of battery energy.This paper presents a cell screening algorithm that integrates genetic and numerical differentiation techniques.Initially,a mathematical model for battery consistency is established,and a multi-step charging strategy is proposed to satisfy the demands of fast charging technology.Subsequently,the genetic algorithm simulates biological evolution to efficiently search for superior cell combinations within a short time while evaluating capacity,voltage consistency,and charge/discharge efficiency.Finally,through experimental validation and comparative analysis with similar algorithms,our proposed method demonstrates notable advantages in terms of both search efficiency and performance.
基金National Key Project of China (No.PD9521907)the National Science Foundation of China (No.19872025).
文摘It is a new attempt to extend the differential quadrature method(DQM) to stability analysis of the straight and curved centerlinepipes conveying fluid. Emphasis is placed on the study of theinfluences of several parameters on the critical flow velocity.Compared to other methods, this method can more easily deal with thepipe with spring support at its boundaries and asks for much lesscomputing effort while giving ac- ceptable precision in the numericalresults.
文摘This article presents a numerical solution for the flow of a Newtonian fluid over an impermeable stretching sheet embedded in a porous medium with the power law surface velocity and variable thickness in the presence of thermal radiation. The flow is caused by non-linear stretching of a sheet. Thermal conductivity of the fluid is assumed to vary linearly with temperature. The governing partial differential equations （PDEs） are transformed into a system of coupled non-linear ordinary differential equations （ODEs） with appropriate boundary conditions for various physical parameters. The remaining system of ODEs is solved numerically using a differential transformation method （DTM）. The effects of the porous parameter, the wall thickness parameter, the radiation parameter, the thermal conductivity parameter, and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction and the Nusselt numbers are presented. Comparison of the obtained numerical results is made with previously published results in some special cases, with good agreement. The results obtained in this paper confirm the idea that DTM is a powerful mathematical tool and can be applied to a large class of linear and non-linear problems in different fields of science and engineering.
文摘The authors give the solution to the problem of one-dimensional conso l idation of double-layered ground with the use of the differential quadrature me t hod. Case studies showed that the computational results for pore-water pressure in soil layer agreed with those of analytical solution; and that in the computat ional results for the interface of soil layer also agreed with those of the anal ytical solution except for the small discrepancies during shortly after the star t of computation. The advantages of the solution presented in this paper are tha t compared with the analytical solution, it avoids the cumbersome work in solvin g the transcendental equation for eigenvalues, and in the case of the Laplace transform s olution, it can resolve the precision problem in the numerical solution of long time inverse Laplace transform. Because of the matrix form of the solution in th is paper, it is convenient for formulating computational program for engineering practice. The formulas for calculating double-layered ground consolidation may be easily extended to the case of multi-layered soils.
文摘Unconditionally stable higher-order accurate time step integration algorithms based on the differential quadrature method (DQM) for second-order initial value problems were applied and the quadrature rules of DQM, computing of the weighting coefficients and choices of sampling grid points were discussed. Some numerical examples dealing with the heat transfer problem, the second-order differential equation of imposed vibration of linear single-degree-of-freedom systems and double-degree-of-freedom systems, the nonlinear move differential equation and a beam forced by a changing load were computed, respectively. The results indicated that the algorithm can produce highly accurate solutions with minimal time consumption, and that the system total energy can remain conservative in the numerical computation.
文摘This paper presents a combined application of the finite element method （FEM） and the differential quadrature method （DQM） to vibration and buckling problems of rectangular plates. The proposed scheme combines the geometry flexibility of the FEM and the high accuracy and efficiency of the DQM. The accuracy of the present method is demonstrated by comparing the obtained results with those available in the literature. It is shown that highly accurate results can be obtained by using a small number of finite elements and DQM sample points. The proposed method is suitable for the problems considered due to its simplicity and potential for further development.
基金Item Sponsored by ("863"Program) of China National High Technology Research and Development Program(2009AA04Z143)
文摘The character of the deformation zone on pair cross rolls is different from that of the regular 4-high mill. Considering comprehensive influences of normal stress and shear stress in rolling direction, width direction and thickness direction, the rolling force calculation model of the PC （pair crossed） hot strip mill is built. Taking the entry stress and the exit stress of strip as the boundary conditions, the longitudinal and transverse distribution of rolling force is worked out by the differential method. Then the total rolling force is calculated, and calculated results are verified by experimental data.
基金key Project of the Municipal Commission of Science and Technology of Shanghai
文摘A differential quadrature (DQ) method for orthotropic plates was proposed based on Reddy' s theory of plates with the effects of the higher-order transverse shear deformations. Wang-Bert's DQ approach was also further extended to handle the boundary conditions of plates. The computational convergence was studied, and the numerical results were obtained for different grid spacings and compared with the existing results. The results show that the DQ method is fairly reliable and effective.
文摘In this study, the effects of magnetic field and nanoparticle on the Jeffery- Hamel flow are studied using a powerful analytical method called the Adomian decomposition method （ADM）. The traditional Navier-Stokes equation of fluid mechanics and Maxwell＇s electromagnetism governing equations are reduced to nonlinear ordinary differential equations to model the problem. The obtained results are well agreed with that of the Runge-Kutta method. The present plots confirm that the method has high accuracy for different a, Ha, and Re numbers. The flow field inside the divergent channel is studied for various values of Hartmann ：number and angle of channel. The effect of nanoparticle volume fraction in the absence of magnetic field is investigated.
文摘In this paper,we study the approximate solutions for some of nonlinear Biomathematics models via the e-epidemic SI1I2R model characterizing the spread of viruses in a computer network and SIR childhood disease model.The reduced differential transforms method(RDTM)is one of the interesting methods for finding the approximate solutions for nonlinear problems.We apply the RDTM to discuss the analytic approximate solutions to the SI1I2R model for the spread of virus HCV-subtype and SIR childhood disease model.We discuss the numerical results at some special values of parameters in the approximate solutions.We use the computer software package such as Mathematical to find more iteration when calculating the approximate solutions.Graphical results and discussed quantitatively are presented to illustrate behavior of the obtained approximate solutions.
文摘A differential geometrical method is for the first time used to calculate the effective moduli of a two-phase elastic composite materials with imperfect interface which the inclusions are assumed to be ellipsoidal of revolutions. All of the interface integral items participating in forming the potential and complementary energy functionals of the composite materials are expressed in terms of intrinsic quantities of the ellipsoidal of revolutions. Based on this, the upper and the lower bound for the effective elastic moduli of the composite materials with inclusions described above have been derived. Under three limiting conditions of sphere, disk and needle shaped inclusions, the results of this paper will return to the bounds obtained by Hashin([6]) (1992).
基金The funding was provided by Laboratory Fund (Grant No.SYJJ200320).
文摘This paper aims to solve the resonance failure probability and develop an effective method to estimate the effects of variables and failure modes on failure probability of axially functionally graded material(FGM)pipe conveying fluid.Correspondingly,the natural frequency of axially FGM pipes conveying fluid is calculated using the differential quadrature method(DQM).A variable sensitivity analysis(VSA)is introduced to measure the effect of each random variable,and a mode sensitivity analysis(MSA)is introduced to acquire the importance ranking of failure modes.Then,an active learning Kriging(ALK)method is established to calculate the resonance failure probability and sensitivity indices,which greatly improves the application of resonance reliability analysis for pipelines in engineering practice.Based on the resonance reliability analysis method,the effects of fluid velocity,volume fraction and fluid density of axially FGM pipe conveying fluid on resonance reliability are analyzed.The results demonstrate that the proposed method has great performance in the anti-resonance analysis of pipes conveying fluid.
文摘The generalized differential quadrature method （GDQM） is employed to con- sider the free vibration and critical speed of moderately thick rotating laminated compos- ite conical shells with different boundary conditions developed from the first-order shear deformation theory （FSDT）. The equations of motion are obtained applying Hamilton＇s concept, which contain the influence of the centrifugal force, the Coriolis acceleration, and the preliminary hoop stress. In addition, the axial load is applied to the conical shell as a ratio of the global critical buckling load. The governing partial differential equations are given in the expressions of five components of displacement related to the points ly- ing on the reference surface of the shell. Afterward, the governing differential equations are converted into a group of algebraic equations by using the GDQM. The outcomes are achieved considering the effects of stacking sequences, thickness of the shell, rotating velocities, half-vertex cone angle, and boundary conditions. Furthermore, the outcomes indicate that the rate of the convergence of frequencies is swift, and the numerical tech- nique is superior stable. Three comparisons between the selected outcomes and those of other research are accomplished, and excellent agreement is achieved.
文摘The traditional differential quadrature method was improved by using theupwind difference scheme for the convective terms to solve the coupled two-dimensionalincompressible Navier-stokes equations and heat equation. The new method was compared with theconventional differential quadrature method in the aspects of convergence and accuracy. The resultsshow that the new method is more accurate, and has better convergence than the conventionaldifferential quadrature method for numerically computing the steady-state solution.
基金supported by the Iranian Nanotechnology Development Committee and the University of Kashan(No.363452/10)
文摘The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elasticity theories using the differential quadrature method （DQM） is presented. Main advantages of the MCST over the classical theory （CT） are the inclusion of the asymmetric couple stress tensor and the consideration of only one material length scale parameter. Based on the nonlinear von Karman assumption, the governing equations of equilibrium for the micro-classical plate consid- ering midplane displacements are derived based on the minimum principle of potential energy. Using the DQM, the biaxial and shear critical buckling loads of the micro-plate for various boundary conditions are obtained. Accuracy of the obtained results is validated by comparing the solutions with those reported in the literature. A parametric study is conducted to show the effects of the aspect ratio, the side-to-thickness ratio, Eringen＇s nonlocal parameter, the material length scale parameter, Young＇s modulus of the surface layer, the surface residual stress, the polymer matrix coefficients, and various boundary conditions on the dimensionless uniaxial, biaxial, and shear critical buckling loads. The results indicate that the critical buckling loads are strongly sensitive to Eringen＇s nonlocal parameter, the material length scale parameter, and the surface residual stress effects, while the effect of Young＇s modulus of the surface layer on the critical buckling load is negligible. Also, considering the size dependent effect causes the increase in the stiffness of the orthotropic micro-plate. The results show that the critical biaxial buckling load increases with an increase in G12/E2 and vice versa for E1/E2. It is shown that the nonlinear biaxial buckling ratio decreases as the aspect ratio increases and vice versa for the buckling amplitude. Because of the most lightweight micro-composite materials with high strength/weight and stiffness/weight ratios, it is anticipated that the results of the present work are useful in experimental characterization of the mechanical properties of micro-composite plates in the aircraft industry and other engineering applications.
