This paper proposes a new step-by-step Chebyshev space-time spectral method to analyze the force vibration of functionally graded material structures.Although traditional space-time spectral methods can reduce the acc...This paper proposes a new step-by-step Chebyshev space-time spectral method to analyze the force vibration of functionally graded material structures.Although traditional space-time spectral methods can reduce the accuracy mismatch between tem-poral low-order finite difference and spatial high-order discre tization,the ir time collocation points must increase dramatically to solve highly oscillatory solutions of structural vibration,which results in a surge in computing time and a decrease in accuracy.To address this problem,we introduced the step-by-step idea in the space-time spectral method.The Chebyshev polynomials and Lagrange's equation were applied to derive discrete spatial goverming equations,and a matrix projection method was used to map the calculation results of prev ious steps as the initial conditions of the subsequent steps.A series of numerical experiments were carried out.The results of the proposed method were compared with those obtained by traditional space-time spectral methods,which showed that higher accuracy could be achieved in a shorter computation time than the latter in highly oscillatory cases.展开更多
Almost all solid surfaces are rough.The randomness and complexity of roughness make the behavior of contact deformation,electrical conductivity,and heat transfer between solids elusive.If the solids are subjected to f...Almost all solid surfaces are rough.The randomness and complexity of roughness make the behavior of contact deformation,electrical conductivity,and heat transfer between solids elusive.If the solids are subjected to further tensile,bending,or torsional deformation,will more complex or new contact phenomena occur?Clarifying this issue is of great significance to developing and designing some major equipment serving in extreme environments.展开更多
Existing orthogonal space-time block coding(OSTBC)schemes for backscatter communication systems cannot achieve a full transmission code rate when the tag is equipped with more than two antennas.In this paper,we propos...Existing orthogonal space-time block coding(OSTBC)schemes for backscatter communication systems cannot achieve a full transmission code rate when the tag is equipped with more than two antennas.In this paper,we propose a quasi-orthogonal spacetime block code(QOSTBC)that can achieve a full transmission code rate for backscatter communication systems with a four-antenna tag and then extend the scheme to support tags with 2i antennas.Specifically,we first present the system model for the backscatter system.Next,we propose the QOSTBC scheme to encode the tag signals.Then,we provide the corresponding maximum likelihood detection algorithms to recover the tag signals.Finally,simulation results are provided to demonstrate that our proposed QOSTBC scheme and the detection algorithm can achieve a better transmission code rate or symbol error rate performance for backscatter communication systems compared with benchmark schemes.展开更多
In this paper,we propose a hybrid decode-and-forward and soft information relaying(HDFSIR)strategy to mitigate error propagation in coded cooperative communications.In the HDFSIR approach,the relay operates in decode-...In this paper,we propose a hybrid decode-and-forward and soft information relaying(HDFSIR)strategy to mitigate error propagation in coded cooperative communications.In the HDFSIR approach,the relay operates in decode-and-forward(DF)mode when it successfully decodes the received message;otherwise,it switches to soft information relaying(SIR)mode.The benefits of the DF and SIR forwarding strategies are combined to achieve better performance than deploying the DF or SIR strategy alone.Closed-form expressions for the outage probability and symbol error rate(SER)are derived for coded cooperative communication with HDFSIR and energy-harvesting relays.Additionally,we introduce a novel normalized log-likelihood-ratio based soft estimation symbol(NL-SES)mapping technique,which enhances soft symbol accuracy for higher-order modulation,and propose a model characterizing the relationship between the estimated complex soft symbol and the actual high-order modulated symbol.Further-more,the hybrid DF-SIR strategy is extended to a distributed Alamouti space-time-coded cooperative network.To evaluate the~performance of the proposed HDFSIR strategy,we implement extensive Monte Carlo simulations under varying channel conditions.Results demonstrate significant improvements with the hybrid technique outperforming individual DF and SIR strategies in both conventional and distributed Alamouti space-time coded cooperative networks.Moreover,at a SER of 10^(-3),the proposed NL-SES mapping demonstrated a 3.5 dB performance gain over the conventional averaging one,highlighting its superior accuracy in estimating soft symbols for quadrature phase-shift keying modulation.展开更多
In the present study,molecular dynamic simulation(MD)was used to investigate the plastic deformation process of the Fe-Mn alloys with different Mn contents.The influences of Mn contents ranging from 10%to 30%(at%)on t...In the present study,molecular dynamic simulation(MD)was used to investigate the plastic deformation process of the Fe-Mn alloys with different Mn contents.The influences of Mn contents ranging from 10%to 30%(at%)on the deformation behavior and the controlling mechanism of the Fe-base alloys were analyzed.The results show that phase transformations and{112}<111>_(BCC)deformation twinning occur in all Fe-Mn alloys but follow different deformation paths.In the Fe-10%Mn alloy the deformation twinning mechanism obeys the FCC-related path,the Fe-20%Mn alloy involves both the FCC-and HCP-related paths,and the deformation of the Fe-30%Mn alloy is dominated by the HCP-related twinning path.The addition of Mn can increase the stacking fault energy and retard the activation of slip systems as well as the formation of stacking faults.Thus,a higher content of Mn can delay the FCC®ε-martensite and the subsequentε-martensite®BCC phase transition at the intersection of twoε-martensitic bands.Therefore,the addition of Mn alloying element increases the yield strength and reduces the elastic modulus of the Fe-Mn alloys.The formation of deformation twins will contribute to the work-hardening effect and delay the necking and fracture of alloys.It is expected that the results in the present study will provide theoretical reference for the design and optimization of high-performance steels.展开更多
The effects of varying strain rates and deformation temperatures on the microstructure evolution of the FGH4113A alloy were investigated through hot compression experiments.During hot deformation,grain evolution is pr...The effects of varying strain rates and deformation temperatures on the microstructure evolution of the FGH4113A alloy were investigated through hot compression experiments.During hot deformation,grain evolution is primarily governed by dynamic recrystallization(DRX)and twinning primarily.Furthermore,the pinning effect of the primaryγ'phase(γ'p phase)plays a crucial role in grain refinement.Lower strain rates or higher temperatures facilitate DRX,twinning,and the dissolution of theγ'p phase.At 1140℃,significant dissolution of theγ'p phase and the subsequent loss of its pinning effect reduce twinning activity.A unique twinning mechanism,termed“pinning twinning”,is identified,occurring exclusively under the influence of the pinning effect.When grain boundary migration fails to accommodate dislocations due to the pinning effect,grains preferentially eliminate dislocations via twinning,thereby reducing local strain energy.The grain size prediction model is improved by considering the pinning effect.展开更多
In subsurface projects where the host rock is of low permeability,fractures play an important role in fluid circulation.Both the geometrical and mechanical properties of the fracture are relevant to the permeability o...In subsurface projects where the host rock is of low permeability,fractures play an important role in fluid circulation.Both the geometrical and mechanical properties of the fracture are relevant to the permeability of the fracture.To evaluate this relationship,we numerically generated self-affine fractures reproducing the scaling relationship of the power spectral density(PSD)of the measured fracture surfaces.The fractures were then subjected to a uniform and stepwise increase in normal stress.A fast Fourier transform(FFT)-based elastic contact model was used to simulate the fracture closure.The evolution of fracture contact area,fracture closure,and fracture normal stiffness were determined throughout the whole process.In addition,the fracture permeability at each step was calculated by the local cubic law(LCL).The influences of roughness exponent and correlation length on the fracture hydraulic and mechanical behaviors were investigated.Based on the power law of normal stiffness versus normal stress,the corrected cubic law and the linear relationship between fracture closure and mechanical aperture were obtained from numerical modeling of a set of fractures.Then,we derived a fracture normal stiffness-permeability equation which incorporates fracture geometric parameters such as the root-mean-square(RMS),roughness exponent,and correlation length,which can describe the fracture flow under an effective medium regime and a percolation regime.Finally,we interpreted the flow transition behavior from the effective medium regime to the percolation regime during fracture closure with the established stiffness-permeability function.展开更多
The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after so...The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after solution treatment was single austenitic phase.The austenite grain size increased with solution temperature and time.A model was established to show the relationship between temperature,time and austenite grain size for the experimental steel.In addition,as the solution temperature increased,the strength decreased,while the elongation first increased and then decreased.This decrease in elongation after solution treatment at 1100℃ for 90 min is contributed to the over-coarse austenite grains.However,after solution treatment at 900℃ for 90 min,the strength-elongation product reached the highest value of 44.4 GPa%.As the austenite grain size increased,the intensity of<111>//tensile direction fiber decreased.This was accompanied by a decrease in dislocation density,resulting in a lower fraction of low-angle grain boundaries and a lower work hardening rate.Therefore,the austenite grain size has a critical influence on the mechanical properties of the low-density steels.Coarser grains lead to a lower yield strength due to the Hall-Petch effect and a lower tensile strength because of lower dislocation strengthening.展开更多
Two actual rocks drilled from a typical ultra-deep hydrocarbon reservoir in the Tarim Basin are selected to conduct in-situ stress-loading micro-focus CT scanning experiments.The gray images of rock microstructure at ...Two actual rocks drilled from a typical ultra-deep hydrocarbon reservoir in the Tarim Basin are selected to conduct in-situ stress-loading micro-focus CT scanning experiments.The gray images of rock microstructure at different stress loading stages are obtained.The U-Net fully convolutional neural network is utilized to achieve fine semantic segmentation of rock skeleton,pore space,and microfractures based on CT slice images of deep rocks.The three-dimensional digital rock models of deformed multiscale fractured-porous media at different stress loading stages are thereafter reconstructed,and the equivalent fracture-pore network models are finally extracted to explore the underlying mechanisms of gas-water two-phase flow at the pore-scale.Results indicate that,in the process of insitu stress loading,both the deep rocks have experienced three stages:linear elastic deformation,nonlinear plastic deformation,and shear failure.The micro-mechanical behavior greatly affects the dynamic deformation of rock microstructure and gas-water two-phase flow.In the linear elastic deformation stage,with the increase in in-situ stress,both the deep rocks are gradually compacted,leading to decreases in average pore radius,pore throat ratio,tortuosity,and water-phase relative permeability,while the coordination number nearly remains unchanged.In the plastic deformation stage,the synergistic influence of rock compaction and existence of micro-fractures typically exert a great effect on pore-throat topological properties and gas-water relative permeability.In the shear failure stage,due to the generation and propagation of micro-fractures inside the deep rock,the topological connectivity becomes better,fluid flow paths increase,and flow conductivity is promoted,thus leading to sharp increases in average pore radius and coordination number,rapid decreases in pore throat ratio and tortuosity,as well as remarkable improvement in relative permeability of gas phase and waterphase.展开更多
The Ti-6Al-4V alloy is the most widely utilized titanium metal alloy globally,making the enhancement of its mechanical properties important.In this study,we achieved an ultimate tensile strength of 1.5 GPa through the...The Ti-6Al-4V alloy is the most widely utilized titanium metal alloy globally,making the enhancement of its mechanical properties important.In this study,we achieved an ultimate tensile strength of 1.5 GPa through the additive manufacturing(AM)of Ti-6Al-4V.Specifically,the Ti-6Al-4V alloy was fabricated via laser powder bed fusion(L-PBF)using Ti-6Al-4V powder subjected to cold plastic deformation(CPD Ti-6Al-4V).The microstructural evolution of the Ti-6Al-4V powder during CPD was analyzed in detail.The CPD Ti-6Al-4V powder exhibited a core-shell structure with subgrains and nanocrystals formed via high-density dislocations within the shell.In addition,the as-printed CPD Ti-6Al-4V alloy had an average grain size of approximately 1.9µm.The presence of interstitial elements and finer grains resulted in the formation of Ti-6Al-4V alloys with ultrahigh strengths(ultimate tensile strength of approximately 1500 MPa,yield strength of 1320 MPa,and elongation of 6%).This groundbreaking achievement paves the way for further advancements in AM technology and presents exciting opportunities for innovation across a range of high-strength materials,which are crucial for achieving optimal performance.展开更多
Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under...Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under uniaxial tension along rolling direction(RD)and transverse direction(TD)at-50,25,50,and 150℃.Results reveal a transition from high strength with limited elongation at-50℃ to significant softening and maximum ductility at 150℃.TD samples consistently showed 2%-6%higher strength than RD;however,this yield anisotropy diminished at 150℃ due to the shift from twinning to thermally activated slip and recovery.Fractography indicated a change from semi-brittle to fully ductile fracture with increasing temperature.Electron backscattered diffraction(EBSD)analysis confirmed twinning-driven grain refinement at low temperatures,while deformation at high temperatures involved grain elongation along shear zones,enabling greater strain accommodation before material failure.展开更多
Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study el...Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
On the basis of Discontinuous Deformation Analysis (DDA), and considering the moderate intrusion of specific block boundaries to different extents, the first-order block motion model is established for the northeaster...On the basis of Discontinuous Deformation Analysis (DDA), and considering the moderate intrusion of specific block boundaries to different extents, the first-order block motion model is established for the northeastern margin of Qinghai-Xizang(Tibet) block and the kinematical model for depicting deformation of small regions as well by using GPS observations of three periods (1991, 1999 and 2001). By simulating, we obtained the motion features of the first-order blocks between the large WWN faults on the sides of the studied region, the distribution features of the principal strain rate field and the inhomogeneous motion features with space-time of the faults in the northern boundary of the Qinghai-Xizang (Tibet) block.展开更多
A new scheme combining a scalable transcoder with space time block codes （STBC） for an orthogonal frequency division multiplexing （OFDM） system is proposed for robust video transmission in dispersive fading channe...A new scheme combining a scalable transcoder with space time block codes （STBC） for an orthogonal frequency division multiplexing （OFDM） system is proposed for robust video transmission in dispersive fading channels. The target application for such a scalable transcoder is to provide successful access to the pre-encoded high quality video MPEG-2 from mobile wireless terminals. In the scalable transcoder, besides outputting the MPEG-4 fine granular scalability （FGS） bitstream, both the size of video frames and the bit rate are reduced. And an array processing algorithm of layer interference suppression is used at the receiver which makes the system structure provide different levels of protection to different layers. Furthermore, by considering the important level of scalable bitstream, the different bitstreams can be given different level protection by the system structure and channel coding. With the proposed system, the concurrent large diversity gain characteristic of STBC and alleviation of the frequency-selective fading effect of OFDM can be achieved. The simulation results show that the proposed schemes integrating scalable transcoding can provide a basic quality of video transmission and outperform the conventional single layer transcoding transmitted under the random and bursty error channel conditions.展开更多
Microstructure and texture evolution of Cu-0.23%Al2O3 dispersion strengthened copper alloy, deformed at room temperature or cryogenic temperature, were investigated. The main textures in hot-extruded specimen were Bra...Microstructure and texture evolution of Cu-0.23%Al2O3 dispersion strengthened copper alloy, deformed at room temperature or cryogenic temperature, were investigated. The main textures in hot-extruded specimen were Brass {011} 〈211〉 and Cube {100} 〈100〉. Textures of Brass {011} 〈211〉 and Goss {011} 〈100〉 were observed in specimen after deformation at room temperature; while textures of Brass {011} 〈211〉, Goss {011} 〈100〉 and S {123} 〈634〉 were detected after deformation at cryogenic temperature. It is believed that the additional Al2O3 nanoparticles can result in dislocation pinning effect, which can further lead to the suppression of dislocations cross-slip. While in the specimen deformed at cryogenic temperature, both pinning effect and cryogenic temperature are responsible for the formation of Brass, Goss and S textures.展开更多
The performance loss of an approximately 3 dB signal-to-noise ratio is always paid with conventional differential detection compared to the related coherent detection. A new detection scheme consisting of two steps is...The performance loss of an approximately 3 dB signal-to-noise ratio is always paid with conventional differential detection compared to the related coherent detection. A new detection scheme consisting of two steps is proposed for the differential unitary space-time modulation （DUSTM） system. In the first step, the data sequence is estimated by conventional unitary space-time demodulation （DUSTD） and differentially encoded again to produce an initial estimate of the transmitted symbol stream. In the second step, the initial estimate of the symbol stream is utilized to initialize an expectation maximization （EM）-based iterative detector. In each iteration, the most recent detected symbol stream is employed to estimate the channel, which is then used to implement coherent sequence detection to refine the symbol stream. Simulation results show that the proposed detection scheme performs much better than the conventional DUSTD after several iterations.展开更多
基金supported by the Advance Research Project of Civil Aerospace Technology(Grant No.D020304)National Nat-ural Science Foundation of China(Grant Nos.52205257 and U22B2083).
文摘This paper proposes a new step-by-step Chebyshev space-time spectral method to analyze the force vibration of functionally graded material structures.Although traditional space-time spectral methods can reduce the accuracy mismatch between tem-poral low-order finite difference and spatial high-order discre tization,the ir time collocation points must increase dramatically to solve highly oscillatory solutions of structural vibration,which results in a surge in computing time and a decrease in accuracy.To address this problem,we introduced the step-by-step idea in the space-time spectral method.The Chebyshev polynomials and Lagrange's equation were applied to derive discrete spatial goverming equations,and a matrix projection method was used to map the calculation results of prev ious steps as the initial conditions of the subsequent steps.A series of numerical experiments were carried out.The results of the proposed method were compared with those obtained by traditional space-time spectral methods,which showed that higher accuracy could be achieved in a shorter computation time than the latter in highly oscillatory cases.
文摘Almost all solid surfaces are rough.The randomness and complexity of roughness make the behavior of contact deformation,electrical conductivity,and heat transfer between solids elusive.If the solids are subjected to further tensile,bending,or torsional deformation,will more complex or new contact phenomena occur?Clarifying this issue is of great significance to developing and designing some major equipment serving in extreme environments.
基金supported by Beijing Municipal Natural Science Foundation(L222002)the Natural Science Foundation of China(U22B2004).
文摘Existing orthogonal space-time block coding(OSTBC)schemes for backscatter communication systems cannot achieve a full transmission code rate when the tag is equipped with more than two antennas.In this paper,we propose a quasi-orthogonal spacetime block code(QOSTBC)that can achieve a full transmission code rate for backscatter communication systems with a four-antenna tag and then extend the scheme to support tags with 2i antennas.Specifically,we first present the system model for the backscatter system.Next,we propose the QOSTBC scheme to encode the tag signals.Then,we provide the corresponding maximum likelihood detection algorithms to recover the tag signals.Finally,simulation results are provided to demonstrate that our proposed QOSTBC scheme and the detection algorithm can achieve a better transmission code rate or symbol error rate performance for backscatter communication systems compared with benchmark schemes.
基金funded by the Deanship of Graduate Studies and Scientific Research at Jouf University under grant No.(DGSSR-2024-02-02160).
文摘In this paper,we propose a hybrid decode-and-forward and soft information relaying(HDFSIR)strategy to mitigate error propagation in coded cooperative communications.In the HDFSIR approach,the relay operates in decode-and-forward(DF)mode when it successfully decodes the received message;otherwise,it switches to soft information relaying(SIR)mode.The benefits of the DF and SIR forwarding strategies are combined to achieve better performance than deploying the DF or SIR strategy alone.Closed-form expressions for the outage probability and symbol error rate(SER)are derived for coded cooperative communication with HDFSIR and energy-harvesting relays.Additionally,we introduce a novel normalized log-likelihood-ratio based soft estimation symbol(NL-SES)mapping technique,which enhances soft symbol accuracy for higher-order modulation,and propose a model characterizing the relationship between the estimated complex soft symbol and the actual high-order modulated symbol.Further-more,the hybrid DF-SIR strategy is extended to a distributed Alamouti space-time-coded cooperative network.To evaluate the~performance of the proposed HDFSIR strategy,we implement extensive Monte Carlo simulations under varying channel conditions.Results demonstrate significant improvements with the hybrid technique outperforming individual DF and SIR strategies in both conventional and distributed Alamouti space-time coded cooperative networks.Moreover,at a SER of 10^(-3),the proposed NL-SES mapping demonstrated a 3.5 dB performance gain over the conventional averaging one,highlighting its superior accuracy in estimating soft symbols for quadrature phase-shift keying modulation.
基金Project(51901248)supported by the National Natural Science Foundation of ChinaProject(2023JJ40742)supported by the Natural Science Foundation of Hunan Province,China。
文摘In the present study,molecular dynamic simulation(MD)was used to investigate the plastic deformation process of the Fe-Mn alloys with different Mn contents.The influences of Mn contents ranging from 10%to 30%(at%)on the deformation behavior and the controlling mechanism of the Fe-base alloys were analyzed.The results show that phase transformations and{112}<111>_(BCC)deformation twinning occur in all Fe-Mn alloys but follow different deformation paths.In the Fe-10%Mn alloy the deformation twinning mechanism obeys the FCC-related path,the Fe-20%Mn alloy involves both the FCC-and HCP-related paths,and the deformation of the Fe-30%Mn alloy is dominated by the HCP-related twinning path.The addition of Mn can increase the stacking fault energy and retard the activation of slip systems as well as the formation of stacking faults.Thus,a higher content of Mn can delay the FCC®ε-martensite and the subsequentε-martensite®BCC phase transition at the intersection of twoε-martensitic bands.Therefore,the addition of Mn alloying element increases the yield strength and reduces the elastic modulus of the Fe-Mn alloys.The formation of deformation twins will contribute to the work-hardening effect and delay the necking and fracture of alloys.It is expected that the results in the present study will provide theoretical reference for the design and optimization of high-performance steels.
基金supported by the National Key Research and Development Program of China(No.2022YFB3706902)Innovation Project for Graduate Students of Hunan Province+1 种基金China(No.1053320212786)supported in part by the High Performance Computing Center of Central South University,China。
文摘The effects of varying strain rates and deformation temperatures on the microstructure evolution of the FGH4113A alloy were investigated through hot compression experiments.During hot deformation,grain evolution is primarily governed by dynamic recrystallization(DRX)and twinning primarily.Furthermore,the pinning effect of the primaryγ'phase(γ'p phase)plays a crucial role in grain refinement.Lower strain rates or higher temperatures facilitate DRX,twinning,and the dissolution of theγ'p phase.At 1140℃,significant dissolution of theγ'p phase and the subsequent loss of its pinning effect reduce twinning activity.A unique twinning mechanism,termed“pinning twinning”,is identified,occurring exclusively under the influence of the pinning effect.When grain boundary migration fails to accommodate dislocations due to the pinning effect,grains preferentially eliminate dislocations via twinning,thereby reducing local strain energy.The grain size prediction model is improved by considering the pinning effect.
基金supported by the China Postdoctoral Science Foundation Funded Project(Grant No.2023M740385)the Postdoctoral Fellowship Program of CPSF(Grant No.GZC20233326)the support by the Helmholtz Association's Initiative and Networking Fund for the Helmholtz Young Investigator Group ARES(Contract No.VH-NG-1516).
文摘In subsurface projects where the host rock is of low permeability,fractures play an important role in fluid circulation.Both the geometrical and mechanical properties of the fracture are relevant to the permeability of the fracture.To evaluate this relationship,we numerically generated self-affine fractures reproducing the scaling relationship of the power spectral density(PSD)of the measured fracture surfaces.The fractures were then subjected to a uniform and stepwise increase in normal stress.A fast Fourier transform(FFT)-based elastic contact model was used to simulate the fracture closure.The evolution of fracture contact area,fracture closure,and fracture normal stiffness were determined throughout the whole process.In addition,the fracture permeability at each step was calculated by the local cubic law(LCL).The influences of roughness exponent and correlation length on the fracture hydraulic and mechanical behaviors were investigated.Based on the power law of normal stiffness versus normal stress,the corrected cubic law and the linear relationship between fracture closure and mechanical aperture were obtained from numerical modeling of a set of fractures.Then,we derived a fracture normal stiffness-permeability equation which incorporates fracture geometric parameters such as the root-mean-square(RMS),roughness exponent,and correlation length,which can describe the fracture flow under an effective medium regime and a percolation regime.Finally,we interpreted the flow transition behavior from the effective medium regime to the percolation regime during fracture closure with the established stiffness-permeability function.
基金supports from National Natural Science Foundation of China(No.U20A20270)China Postdoctoral Science Foundation(No.2022M722486).
文摘The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after solution treatment was single austenitic phase.The austenite grain size increased with solution temperature and time.A model was established to show the relationship between temperature,time and austenite grain size for the experimental steel.In addition,as the solution temperature increased,the strength decreased,while the elongation first increased and then decreased.This decrease in elongation after solution treatment at 1100℃ for 90 min is contributed to the over-coarse austenite grains.However,after solution treatment at 900℃ for 90 min,the strength-elongation product reached the highest value of 44.4 GPa%.As the austenite grain size increased,the intensity of<111>//tensile direction fiber decreased.This was accompanied by a decrease in dislocation density,resulting in a lower fraction of low-angle grain boundaries and a lower work hardening rate.Therefore,the austenite grain size has a critical influence on the mechanical properties of the low-density steels.Coarser grains lead to a lower yield strength due to the Hall-Petch effect and a lower tensile strength because of lower dislocation strengthening.
基金supported by the National Natural Science Foundation of China(No.52174043)the Beijing Natural Science Foundation(No.3242019)+1 种基金the CNPC Innovation Foundation(No.2022DQ02-0208)the State Key Laboratory of Deep Oil and Gas(No.SKLD0G2024-KFZD-06).
文摘Two actual rocks drilled from a typical ultra-deep hydrocarbon reservoir in the Tarim Basin are selected to conduct in-situ stress-loading micro-focus CT scanning experiments.The gray images of rock microstructure at different stress loading stages are obtained.The U-Net fully convolutional neural network is utilized to achieve fine semantic segmentation of rock skeleton,pore space,and microfractures based on CT slice images of deep rocks.The three-dimensional digital rock models of deformed multiscale fractured-porous media at different stress loading stages are thereafter reconstructed,and the equivalent fracture-pore network models are finally extracted to explore the underlying mechanisms of gas-water two-phase flow at the pore-scale.Results indicate that,in the process of insitu stress loading,both the deep rocks have experienced three stages:linear elastic deformation,nonlinear plastic deformation,and shear failure.The micro-mechanical behavior greatly affects the dynamic deformation of rock microstructure and gas-water two-phase flow.In the linear elastic deformation stage,with the increase in in-situ stress,both the deep rocks are gradually compacted,leading to decreases in average pore radius,pore throat ratio,tortuosity,and water-phase relative permeability,while the coordination number nearly remains unchanged.In the plastic deformation stage,the synergistic influence of rock compaction and existence of micro-fractures typically exert a great effect on pore-throat topological properties and gas-water relative permeability.In the shear failure stage,due to the generation and propagation of micro-fractures inside the deep rock,the topological connectivity becomes better,fluid flow paths increase,and flow conductivity is promoted,thus leading to sharp increases in average pore radius and coordination number,rapid decreases in pore throat ratio and tortuosity,as well as remarkable improvement in relative permeability of gas phase and waterphase.
基金supported by the Guangdong Basic and Applied Basic Research Foundation(No.2020B1515120013)the National Natural Science Foundation of China(Nos.51971108 and 52271032)+1 种基金the Key Research and Development Program of Jiangsu Province(No.K22251901)the Shenzhen Science and Technology Innovation Commission(Nos.JCYJ20220818100612027 and JSGG20210420091802007).
文摘The Ti-6Al-4V alloy is the most widely utilized titanium metal alloy globally,making the enhancement of its mechanical properties important.In this study,we achieved an ultimate tensile strength of 1.5 GPa through the additive manufacturing(AM)of Ti-6Al-4V.Specifically,the Ti-6Al-4V alloy was fabricated via laser powder bed fusion(L-PBF)using Ti-6Al-4V powder subjected to cold plastic deformation(CPD Ti-6Al-4V).The microstructural evolution of the Ti-6Al-4V powder during CPD was analyzed in detail.The CPD Ti-6Al-4V powder exhibited a core-shell structure with subgrains and nanocrystals formed via high-density dislocations within the shell.In addition,the as-printed CPD Ti-6Al-4V alloy had an average grain size of approximately 1.9µm.The presence of interstitial elements and finer grains resulted in the formation of Ti-6Al-4V alloys with ultrahigh strengths(ultimate tensile strength of approximately 1500 MPa,yield strength of 1320 MPa,and elongation of 6%).This groundbreaking achievement paves the way for further advancements in AM technology and presents exciting opportunities for innovation across a range of high-strength materials,which are crucial for achieving optimal performance.
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)the Ministry of Trade,Industry&Energy(MOTIE)of the Republic of Korea Program(No.RS-2025-02603127,Innovation Research Center for Zero-carbon Fuel Gas Turbine Design,Manufacture,and Safety)。
文摘Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under uniaxial tension along rolling direction(RD)and transverse direction(TD)at-50,25,50,and 150℃.Results reveal a transition from high strength with limited elongation at-50℃ to significant softening and maximum ductility at 150℃.TD samples consistently showed 2%-6%higher strength than RD;however,this yield anisotropy diminished at 150℃ due to the shift from twinning to thermally activated slip and recovery.Fractography indicated a change from semi-brittle to fully ductile fracture with increasing temperature.Electron backscattered diffraction(EBSD)analysis confirmed twinning-driven grain refinement at low temperatures,while deformation at high temperatures involved grain elongation along shear zones,enabling greater strain accommodation before material failure.
基金financial support from NSF ExpandQISE program.The synthesis of tellurene was supported by NSF under grant no.CMMI-2046936supports from Purdue Research Foundation.
文摘Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
文摘On the basis of Discontinuous Deformation Analysis (DDA), and considering the moderate intrusion of specific block boundaries to different extents, the first-order block motion model is established for the northeastern margin of Qinghai-Xizang(Tibet) block and the kinematical model for depicting deformation of small regions as well by using GPS observations of three periods (1991, 1999 and 2001). By simulating, we obtained the motion features of the first-order blocks between the large WWN faults on the sides of the studied region, the distribution features of the principal strain rate field and the inhomogeneous motion features with space-time of the faults in the northern boundary of the Qinghai-Xizang (Tibet) block.
文摘A new scheme combining a scalable transcoder with space time block codes （STBC） for an orthogonal frequency division multiplexing （OFDM） system is proposed for robust video transmission in dispersive fading channels. The target application for such a scalable transcoder is to provide successful access to the pre-encoded high quality video MPEG-2 from mobile wireless terminals. In the scalable transcoder, besides outputting the MPEG-4 fine granular scalability （FGS） bitstream, both the size of video frames and the bit rate are reduced. And an array processing algorithm of layer interference suppression is used at the receiver which makes the system structure provide different levels of protection to different layers. Furthermore, by considering the important level of scalable bitstream, the different bitstreams can be given different level protection by the system structure and channel coding. With the proposed system, the concurrent large diversity gain characteristic of STBC and alleviation of the frequency-selective fading effect of OFDM can be achieved. The simulation results show that the proposed schemes integrating scalable transcoding can provide a basic quality of video transmission and outperform the conventional single layer transcoding transmitted under the random and bursty error channel conditions.
基金Project(51271203)supported by the National Natural Science Foundation of ChinaProject(YSZN2013CLD6)supported by the Nonferrous Metals Science Foundation of HNG-CSU+1 种基金ChinaProject supported by the Program Between the CSC(China Scholarship Council)and the DAAD(German Academic Exchange Service)
文摘Microstructure and texture evolution of Cu-0.23%Al2O3 dispersion strengthened copper alloy, deformed at room temperature or cryogenic temperature, were investigated. The main textures in hot-extruded specimen were Brass {011} 〈211〉 and Cube {100} 〈100〉. Textures of Brass {011} 〈211〉 and Goss {011} 〈100〉 were observed in specimen after deformation at room temperature; while textures of Brass {011} 〈211〉, Goss {011} 〈100〉 and S {123} 〈634〉 were detected after deformation at cryogenic temperature. It is believed that the additional Al2O3 nanoparticles can result in dislocation pinning effect, which can further lead to the suppression of dislocations cross-slip. While in the specimen deformed at cryogenic temperature, both pinning effect and cryogenic temperature are responsible for the formation of Brass, Goss and S textures.
基金The National Natural Science Foundation of China(No60572072,60496311)the National High Technology Research and Development Program of China (863Program) (No2006AA01Z264)+1 种基金the National Basic Research Program of China (973Program) (No2007CB310603)the PhD Programs Foundation of Ministry of Educa-tion of China (No20060286016)
文摘The performance loss of an approximately 3 dB signal-to-noise ratio is always paid with conventional differential detection compared to the related coherent detection. A new detection scheme consisting of two steps is proposed for the differential unitary space-time modulation （DUSTM） system. In the first step, the data sequence is estimated by conventional unitary space-time demodulation （DUSTD） and differentially encoded again to produce an initial estimate of the transmitted symbol stream. In the second step, the initial estimate of the symbol stream is utilized to initialize an expectation maximization （EM）-based iterative detector. In each iteration, the most recent detected symbol stream is employed to estimate the channel, which is then used to implement coherent sequence detection to refine the symbol stream. Simulation results show that the proposed detection scheme performs much better than the conventional DUSTD after several iterations.
