With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limite...With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limited.This poses challenges for conventional fault distance estimation methods,which are often tailored to simple topologies and are thus difficult to apply to large-scale,multi-node DC networks.To address this,a fault distance estimation method based on sparse measurement of high-frequency electrical quantities is proposed in this paper.First,a preliminary fault line identification model based on compressed sensing is constructed to effectively narrow the fault search range and improve localization efficiency.Then,leveraging the high-frequency impedance characteristics and the voltage-current relationship of electrical quantities,a fault distance estimation approach based on high-frequency measurements from both ends of a line is designed.This enables accurate distance estimation even when the measurement devices are not directly placed at both ends of the faulted line,overcoming the dependence on specific sensor placement inherent in traditional methods.Finally,to further enhance accuracy,an optimization model based on minimizing the high-frequency voltage error at the fault point is introduced to reduce estimation error.Simulation results demonstrate that the proposed method achieves a fault distance estimation error of less than 1%under normal conditions,and maintains good performance even under adverse scenarios.展开更多
Development of the medium and low voltage DC distribution system is of great significance to a regional transmission of electric energy,increasing a penetration rate of new energy,and enhancing a safety of the operati...Development of the medium and low voltage DC distribution system is of great significance to a regional transmission of electric energy,increasing a penetration rate of new energy,and enhancing a safety of the operation of the AC/DC interconnected grid.This paper first summarizes the medium and low voltage DC distribution system schemes and plans put forward by many countries,and then elaborate status of under-construction medium and low voltage DC distribution system project cases in China.Based on these project cases,this paper analyzes key issues involved in the medium and low voltage DC distribution system topologies,equipment,operation control technologies and DC fault protections,in order to provide theoretical and technical reference for future medium and low voltage DC distribution system-related projects.Finally,this paper combines a current China research status to summarize and give a prediction about the future research direction of medium and low voltage DC distribution system,which can provide reference for the research of medium and low voltage DC distribution system.展开更多
A novel operation control method for relay protection in flexible DC distribution networks with distributed power supply is proposed to address the issue of inaccurate fault location during relay protection,leading to...A novel operation control method for relay protection in flexible DC distribution networks with distributed power supply is proposed to address the issue of inaccurate fault location during relay protection,leading to poor performance.The method combines a fault-tolerant fault location method based on long-term and short-term memory networks to accurately locate the fault section.Then,an operation control method for relay protection based on adaptive weight and whale optimization algorithm(WOA)is used to construct an objective function considering the shortest relay protection action time and the smallest impulse current.The adaptive weight and WOA are employed to obtain the optimal strategy for relay protection operation control,reducing the action time and impulse current.Experimental results demonstrate the effectiveness of the proposed method in accurately locating faults and improving relay protection performance.The longest operation time is reduced by 4.7023 s,and the maximum impulse current is limited to 0.3 A,effectively controlling the impact of large impulse currents and enhancing control efficiency.展开更多
Multi-converter approach based on the series and parallel connection topology of modular power converters has been proposed to realize higher power density DC-DC converter. The availability of the proposed approach ha...Multi-converter approach based on the series and parallel connection topology of modular power converters has been proposed to realize higher power density DC-DC converter. The availability of the proposed approach has been verified through the design consideration and the experiment. The design consideration for two DC-DC converters has been carried out by utilizing the power converter exact loss simulator, and the design parameters to maximize their power densities have been extracted taking the trade-off between the conversion efficiency and the power density into account. The prototypes of a 2,400 W, 256-384 V boost chopper using SiC-MOSFETs and a 300 W, 32-48 V GaN-FETs boost chopper have been also developed based on the design. The SiC chopper achieved the efficiency of 97.8% and the power density of 12,8 W/cm3, and the GaN chopper accomplished 98.9% and 18.6 W/cm3 in the experiment. These results show the validity of the design and the availability of the proposed approach. The multi-converter approach enables the cost reduction of the modular power converters, and contributes to realizing the widespread use of power electronics converters in the future 380 V DC distribution system.展开更多
By integrating advanced digital technologies such as cloud computing and the Internet of Things in sensor measurement,information communication,and other fields,the digital DC distribution network can efficiently and ...By integrating advanced digital technologies such as cloud computing and the Internet of Things in sensor measurement,information communication,and other fields,the digital DC distribution network can efficiently and reliably access DistributedGenerator(DG)and Energy Storage Systems(ESS),exhibiting significant advantages in terms of controllability and meeting requirements of Plug-and-Play(PnP)operations.However,during device plug-in and-out processes,improper systemparametersmay lead to small-signal stability issues.Therefore,before executing PnP operations,conducting stability analysis and adjusting parameters swiftly is crucial.This study introduces a four-stage strategy for parameter optimization to enhance systemstability efficiently.In the first stage,state-of-the-art technologies in measurement and communication are utilized to correct model parameters.Then,a novel indicator is adopted to identify the key parameters that influence stability in the second stage.Moreover,in the third stage,a local-parameter-tuning strategy,which leverages rapid parameter boundary calculations as a more efficient alternative to plotting root loci,is used to tune the selected parameters.Considering that the local-parameter-tuning strategy may fail due to some operating parameters being limited in adjustment,a multiparameter-tuning strategy based on the particle swarm optimization(PSO)is proposed to comprehensively adjust the dominant parameters to improve the stability margin of the system.Lastly,system stability is reassessed in the fourth stage.The proposed parameter-optimization strategy’s effectiveness has been validated through eigenvalue analysis and nonlinear time-domain simulations.展开更多
The DC distribution network system equipped with a large number of power electronic equipment exhibits weak damping characteristics and is prone to low-frequency and high-frequency unstable oscillations.The current in...The DC distribution network system equipped with a large number of power electronic equipment exhibits weak damping characteristics and is prone to low-frequency and high-frequency unstable oscillations.The current interpretation of the oscillation mechanism has not been unified.Firstly,this paper established the complete statespace model of the distribution system consisting of a large number of electric vehicles,characteristic equation of the distribution network system is derived by establishing a state-space model,and simplified reduced-order equations describing the low-frequency oscillation and the high-frequency oscillation are obtained.Secondly,based on eigenvalue analysis,the oscillation modes and the influence of the key system parameters on the oscillation mode are studied.Besides,impacts of key factors,such as distribution network connection topology and number of dynamic loads,have been discussed to suppress oscillatory instability caused by inappropriate design or dynamic interactions.Finally,using the DC distribution example system,through model calculation and time-domain simulation analysis,the correctness of the aforementioned analysis is verified.展开更多
The escalating deployment of distributed power sources and random loads in DC distribution networks hasamplified the potential consequences of faults if left uncontrolled. To expedite the process of achieving an optim...The escalating deployment of distributed power sources and random loads in DC distribution networks hasamplified the potential consequences of faults if left uncontrolled. To expedite the process of achieving an optimalconfiguration of measurement points, this paper presents an optimal configuration scheme for fault locationmeasurement points in DC distribution networks based on an improved particle swarm optimization algorithm.Initially, a measurement point distribution optimization model is formulated, leveraging compressive sensing.The model aims to achieve the minimum number of measurement points while attaining the best compressivesensing reconstruction effect. It incorporates constraints from the compressive sensing algorithm and networkwide viewability. Subsequently, the traditional particle swarm algorithm is enhanced by utilizing the Haltonsequence for population initialization, generating uniformly distributed individuals. This enhancement reducesindividual search blindness and overlap probability, thereby promoting population diversity. Furthermore, anadaptive t-distribution perturbation strategy is introduced during the particle update process to enhance the globalsearch capability and search speed. The established model for the optimal configuration of measurement points issolved, and the results demonstrate the efficacy and practicality of the proposed method. The optimal configurationreduces the number of measurement points, enhances localization accuracy, and improves the convergence speedof the algorithm. These findings validate the effectiveness and utility of the proposed approach.展开更多
ADC distribution network is an effective solution for increasing renewable energy utilization with distinct benefits,such as high efficiency and easy control.However,a sudden increase in the current after the occurren...ADC distribution network is an effective solution for increasing renewable energy utilization with distinct benefits,such as high efficiency and easy control.However,a sudden increase in the current after the occurrence of faults in the network may adversely affect network stability.This study proposes an artificial neural network(ANN)-based fault detection and protection method for DC distribution networks.The ANN is applied to a classifier for different faults ontheDC line.The backpropagationneuralnetwork is used to predict the line current,and the fault detection threshold is obtained on the basis of the difference between the predicted current and the actual current.The proposed method only uses local signals,with no requirement of a strict communication link.Simulation experiments are conducted for the proposed algorithm on a two-terminal DC distribution network modeled in the PSCAD/EMTDC and developed on the MATLAB platform.The results confirm that the proposed method can accurately detect and classify line faults within a few milliseconds and is not affected by fault locations,fault resistance,noise,and communication delay.展开更多
GaN （gallium nitride） buck-rectifier has been proposed to realize high power density ISOP （input series and output parallel）-IPOS （input parallel and output series） converter-based dc distribution system. The ul...GaN （gallium nitride） buck-rectifier has been proposed to realize high power density ISOP （input series and output parallel）-IPOS （input parallel and output series） converter-based dc distribution system. The ultra-low loss bi-directional switch can be developed by the GaN power device because of the low on-resistance, the high-speed switching behavior and its own device structure. The buck-rectifier using the GaN bi-directional switches has the potential to achieve higher power density than the commonly utilized boost-rectifier. Availability of the GaN-HEMT （high electron mobility transistor） for the buck rectifier has been verified taking the theoretical limit of the on-resistance and the switching loss energy into account. Design consideration for a high power density buck-rectifier has been also conducted and the application effect of the GaN bidirectional switches has been evaluated quantitatively. The ISOP-IPOS converter-based dc （direct current） distribution system takes full advantage of the buck-rectifier and the rectifier using GaN devices contributes to realizing higher power density dc distribution system.展开更多
This paper presents an optimal operation method for embedded DC interconnections based on low-voltage AC/DC distribution areas(EDC-LVDA)under three-phase unbalanced compensation conditions.It can optimally determine t...This paper presents an optimal operation method for embedded DC interconnections based on low-voltage AC/DC distribution areas(EDC-LVDA)under three-phase unbalanced compensation conditions.It can optimally determine the transmission power of the DC and AC paths to simultaneously improve voltage quality and reduce losses.First,considering the embedded interconnected,unbalanced power structure of the distribution area,a power flow calculation method for EDC-LVDA that accounts for three-phase unbalanced compensation is introduced.This method accurately describes the power flow distribution characteristics under both AC and DC power allocation scenarios.Second,an optimization scheduling model for EDC-LVDA under three-phase unbalanced conditions is developed,incorporating network losses,voltage quality,DC link losses,and unbalance levels.The proposed model employs an improved particle swarm optimization(IPSO)two-layer algorithm to autonomously select different power allocation coefficients for the DC link and AC section under various operating conditions.This enables embedded economic optimization scheduling while maintaining compensation for unbalanced conditions.Finally,a case study based on the IEEE 13-node system for EDC-LVDA is conducted and tested.The results show that the proposed optimal operation method achieves a 100%voltage compliance rate and reduces network losses by 13.8%,while ensuring three-phase power balance compensation.This provides a practical solution for the modernization and upgrading of low-voltage power grids.展开更多
DC series-parallel power flow controller(SP-PFC)is a highly efficient device to solve the problem of uncontrolled line current in the bipolar DC distribution system.However,its potential in fault current limiting is n...DC series-parallel power flow controller(SP-PFC)is a highly efficient device to solve the problem of uncontrolled line current in the bipolar DC distribution system.However,its potential in fault current limiting is not fully explored.In this paper,a self-adaptive action strategy(SAAS)and a parameter optimization method of SP-PFC in bipolar DC distribution systems are proposed.Firstly,the common-and different-mode(CDM)equivalent circuits of the bipolar DC distribution system with SP-PFC in different fault stages are established,which avoids the line coupling inductance.Based on this,the influence of different parameters and line coupling inductance on the fault current limiting capability are investigated.It is found that the SP-PFC has the best fault current limiting capability when the capacitance and inductance of filter are inversely proportional.To realize the adaptability of fault current limiting capability under different fault severities,the SAAS of SP-PFC is proposed.The validity of the CDM equivalent circuits and parameter optimization method,and the effectiveness of the SAAS are verified by simulations and experiments.展开更多
Optimal Power Flow (OPF) plays a crucial role in optimization and operation of the bipolar DC distribution network (Bi-DCDN). However, existing OPF models encounter difficulties in the power optimization of Bi-DCDNs d...Optimal Power Flow (OPF) plays a crucial role in optimization and operation of the bipolar DC distribution network (Bi-DCDN). However, existing OPF models encounter difficulties in the power optimization of Bi-DCDNs due to the optimal power expressed as a product form, i.e., the product of voltage and current. Hence, this brief formulates the OPF problem of Bi-DCDNs using the branch flow model (BFM). The BFM employs power, instead of current, to account for the unique structure of Bi-DCDNs. Convex relaxation and linear approximation are sequentially applied to reformulate the BFM-based OPF, presenting it as a second-order cone programming (SOCP) problem. Further, the effectiveness of the proposed OPF model is verified in case studies. The numerical results demonstrate that the BFM-based OPF is a feasible and promising approach for Bi-DCDNs.展开更多
The multi-voltage-level DC distribution network(MVL-DC-DN)is a promising network for efficiently integrat ing rapidly growing DC loads,and fast-growing load demand would bring a challenge to the MVL-DC-DN in terms of ...The multi-voltage-level DC distribution network(MVL-DC-DN)is a promising network for efficiently integrat ing rapidly growing DC loads,and fast-growing load demand would bring a challenge to the MVL-DC-DN in terms of the maximum loadability.This paper considers the DC electric spring(DC-ES)as a novel candidate flexible resource for en hancing the maximum loadability of the MVL-DC-DN,and pro poses an evaluation method for the maximum loadability.First ly,with the consideration of device constraints,the impact that the DC-ES on the maximum loadability of the DC distribution network(DC-DN)is analyzed via a simplified equivalent cir cuit.Subsequently,the power flow(PF)model of an MVL-DCDN with DC-ESs is established.Finally,a method based on con tinuation power flow(CPF)for evaluating the maximum load ability of an MVL-DC-DN with DC-ESs is proposed.During the evaluation,limitations of the DC-ES and the DC transform er(DCT)are considered.The consideration of the practical con straints avoids the overestimation of the maximum loadability.The case study verifies the effectiveness of the proposed method.展开更多
A novel single-ended online fault location algorithm is investigated for DC distribution networks. The proposed algorithm calculates the fault distance based on the characteristics of the voltage resonance. The Prony&...A novel single-ended online fault location algorithm is investigated for DC distribution networks. The proposed algorithm calculates the fault distance based on the characteristics of the voltage resonance. The Prony's method is introduced to extract the characteristics. A novel method is proposed to solve the pseudo dual-root problem in the calculation process. The multiple data windows are adopted to enhance the robustness of the proposed algorithm. An index is proposed to evaluate the accuracy and validity of the results derived from the various data windows. The performances of the proposed algorithm in different fault scenarios were evaluated using the PSCAD/EMTDC simulations. The results show that the algorithm can locate the faults with transient resistance using the 1.6 ms data of the DC-side voltage after a fault inception and offers a good precision.展开更多
With the development of power electronic technologies and distributed power generation,DC distribution networks attract increasing attention due to their various advantages compared with traditional AC distribution ne...With the development of power electronic technologies and distributed power generation,DC distribution networks attract increasing attention due to their various advantages compared with traditional AC distribution networks.However,DC fault protection is one of the major issues in DC distribution networks.To improve their reliability and protect the semiconductor devices under DC faults,a current-limiting and energy-transferring DC circuit breaker topology is proposed in this paper.By applying passive components and thyristors,the proposed topology is capable of quickly limiting the fault current and transferring the faulty energy.The working principle,mathematical model and parameter designing method of the proposed topology are presented in this paper.The simulation results verify that the proposed DC circuit breaker could effectively limit the fault current and quickly interrupt the fault current.Cost and conduction power loss evaluation proves the practicality of the proposed topology in medium-voltage DC distribution networks.展开更多
The concept of a flexible power electronics substation(FPES)was first applied in the Zhangbei DC distribution network demonstration project.As a multi-port power electronics transformer(PET)with different AC and DC vo...The concept of a flexible power electronics substation(FPES)was first applied in the Zhangbei DC distribution network demonstration project.As a multi-port power electronics transformer(PET)with different AC and DC voltage levels,the FPES has adopted a novel topology integrating modular multilevel converter(MMC)and four-winding medium frequency transformer(FWMFT)based multiport DC-DC converter,which can significantly reduce capacitance in each sub-module(SM)of a MMC and also save space and cost.In this paper,in order to accelerate speed of electromagnetic transient(EMT)simulations of FPES based hybrid AC/DC distribution systems,an averaged-value model(AVM)is proposed for efficient and accurate representation of FPES.Assume that all SM capacitor voltages are perfectly balanced in the MMC,then the MMC behavior can be modeled using controlled voltage sources based on modulation voltages from control systems.In terms of the averaged current transfer characteristics among the windings of the FWMFT,we consider that all multiport DC-DC converters are controlled with the same dynamics,a lumped averaged model using controlled current and voltage sources has been developed for these four-port DC-DC converters connected to the upper or lower arms of the MMC.The presented FPES AVM model has been tested and validated by comparison with a detailed IGBT-based EMT model.Results show that the AVM is significantly more efficient while maintaining its accuracy in an EMT simulation.展开更多
As the structures of multiple branch lines(MBLs)will be widely applied in the future flexible DC distribution network,there is a urgent need for improving system reliability by tackling the frequent non-permanent pole...As the structures of multiple branch lines(MBLs)will be widely applied in the future flexible DC distribution network,there is a urgent need for improving system reliability by tackling the frequent non-permanent pole-to-pole(P-P)fault on distribution lines.A novel fault restoration strategy based on local information is proposed to solve this issue.The strategy firstly splits a double-ended power supply network into two single-ended power supply networks through the timing difference characteristics of a hybrid direct current circuit breaker(HDCCB)entering the recloser.Then,a method based on the characteristic of the transient energy of fault current is proposed to screen the faulty branch line in each single-ended power supply network.Also,a four-terminal flexible DC distribution network with MBLs is constructed on PSCAD to demonstrate the efficacy of the proposed strategy.Various factors such as noise,fault location,and DC arc equivalent resistance are considered in the simulation model for testing.Test results prove that the proposed strategy for fault restoration is effective,and features high performance and scalability.展开更多
Due to the advantages such as low line cost,low transmission loss,and high power supply reliability,DC distribution networks have become the main development trend for future distribution networks.In this paper,a typi...Due to the advantages such as low line cost,low transmission loss,and high power supply reliability,DC distribution networks have become the main development trend for future distribution networks.In this paper,a typical DC distribution network with multiple voltage levels is considered as a research object.It is proposed that the interface converters between DC buses with different voltage levels be implemented through the series-parallel combination of full-bridge LLC resonant converters.To realize the decentralized self-discipline control of DC voltage under various working conditions,different slack buses are prepared according to the voltage ranges of the DC buses,and the voltage regulation modes of the DC distribution network are divided into main voltage regulation mode,backup voltage regulation mode,and off-grid voltage droop regulation mode.By introducing a voltage coefficient related to DC voltage deviation as a basis for mode switching,the voltage fluctuations caused by slow switching between control modes in the method of traditional voltage margin control is reduced,facilitating fast and smooth switching between different voltage regulation modes.Finally,a simulation model for DC distribution networks is constructed utilizing MATLAB/Simulink.Simulation results verify the effectiveness and feasibility of the proposed voltage regulation modes and switching methods for DC distribution networks.Finally,an experimental platform is also constructed to verify the feasibility of the mode switching method proposed in this paper.展开更多
The bipolar low-voltage DC(LVDC) distribution system has become a prospective solution to better integration of renewables and improvement of system efficiency and reliability. However, it also faces the challenge of ...The bipolar low-voltage DC(LVDC) distribution system has become a prospective solution to better integration of renewables and improvement of system efficiency and reliability. However, it also faces the challenge of power and voltage imbalance between two poles. To solve this problem, an interface converter with bipolar asymmetrical operating capabilities is applied in this paper. The steady-state models of the bipolar LVDC distribution system equipped with this interface converter in the gridconnected mode and off-grid mode are analyzed. A control scheme based on DC offset injection at the secondary side of the interface converter is proposed, enabling the bipolar LVDC distribution system to realize the unbalanced power transfer between two poles in the grid-connected mode and maintain the inherentpole voltage balance in the off-grid mode. Furthermore, this paper also proposes a primary-side DC offset injection control scheme according to the analysis of the magnetic circuit model, which can eliminate the DC bias flux caused by the secondaryside DC offset. Thereby, the potential core magnetic saturation and overcurrent issues can be prevented, ensuring the safety of the interface converter and distribution system. Detailed simulations based on the proposed control scheme are conducted to validate the function of power and voltage balance under the operation conditions of different DC loads.展开更多
DC technologies will be essential building blocks for future DC distribution networks.As in any DC system,these networks will face crucial threats imposed by short-circuit DC faults.Protection is thus of great interes...DC technologies will be essential building blocks for future DC distribution networks.As in any DC system,these networks will face crucial threats imposed by short-circuit DC faults.Protection is thus of great interest,and it will likely rely on DC circuit breakers(DCCBs).Among available configurations,Z-source solid-state circuit breakers(Z-SSCBs)are promising candidates for protecting low and medium-voltage distribution networks,as well as DC equipment due to their structural and control simplicity and low cost.In this paper,start-ofthe-art of Z-SSCBs topologies is reviewed.To set the context,the use of DC technologies for grid integration of renewables,DC power transmission,and the main types of DCCBs to protect DC transmission and distribution corridors are discussed.The Z-SSCB topologies are then classified into unidirectional and bidirectional.Advantages and disadvantages of different configurations are compared and analyzed based on existing research.Finally,a perspective on the future development of Z-SSCBs is discussed and potential challenges are elucidated.展开更多
基金National Natural Science Foundation of China, grant number 52177074.
文摘With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limited.This poses challenges for conventional fault distance estimation methods,which are often tailored to simple topologies and are thus difficult to apply to large-scale,multi-node DC networks.To address this,a fault distance estimation method based on sparse measurement of high-frequency electrical quantities is proposed in this paper.First,a preliminary fault line identification model based on compressed sensing is constructed to effectively narrow the fault search range and improve localization efficiency.Then,leveraging the high-frequency impedance characteristics and the voltage-current relationship of electrical quantities,a fault distance estimation approach based on high-frequency measurements from both ends of a line is designed.This enables accurate distance estimation even when the measurement devices are not directly placed at both ends of the faulted line,overcoming the dependence on specific sensor placement inherent in traditional methods.Finally,to further enhance accuracy,an optimization model based on minimizing the high-frequency voltage error at the fault point is introduced to reduce estimation error.Simulation results demonstrate that the proposed method achieves a fault distance estimation error of less than 1%under normal conditions,and maintains good performance even under adverse scenarios.
基金supported by the National Key Rese arch and Development Program of China(2018YFB0904100)Science and Technology Project of State Grid(SGHB0000KXJS1800685)
文摘Development of the medium and low voltage DC distribution system is of great significance to a regional transmission of electric energy,increasing a penetration rate of new energy,and enhancing a safety of the operation of the AC/DC interconnected grid.This paper first summarizes the medium and low voltage DC distribution system schemes and plans put forward by many countries,and then elaborate status of under-construction medium and low voltage DC distribution system project cases in China.Based on these project cases,this paper analyzes key issues involved in the medium and low voltage DC distribution system topologies,equipment,operation control technologies and DC fault protections,in order to provide theoretical and technical reference for future medium and low voltage DC distribution system-related projects.Finally,this paper combines a current China research status to summarize and give a prediction about the future research direction of medium and low voltage DC distribution system,which can provide reference for the research of medium and low voltage DC distribution system.
文摘A novel operation control method for relay protection in flexible DC distribution networks with distributed power supply is proposed to address the issue of inaccurate fault location during relay protection,leading to poor performance.The method combines a fault-tolerant fault location method based on long-term and short-term memory networks to accurately locate the fault section.Then,an operation control method for relay protection based on adaptive weight and whale optimization algorithm(WOA)is used to construct an objective function considering the shortest relay protection action time and the smallest impulse current.The adaptive weight and WOA are employed to obtain the optimal strategy for relay protection operation control,reducing the action time and impulse current.Experimental results demonstrate the effectiveness of the proposed method in accurately locating faults and improving relay protection performance.The longest operation time is reduced by 4.7023 s,and the maximum impulse current is limited to 0.3 A,effectively controlling the impact of large impulse currents and enhancing control efficiency.
文摘Multi-converter approach based on the series and parallel connection topology of modular power converters has been proposed to realize higher power density DC-DC converter. The availability of the proposed approach has been verified through the design consideration and the experiment. The design consideration for two DC-DC converters has been carried out by utilizing the power converter exact loss simulator, and the design parameters to maximize their power densities have been extracted taking the trade-off between the conversion efficiency and the power density into account. The prototypes of a 2,400 W, 256-384 V boost chopper using SiC-MOSFETs and a 300 W, 32-48 V GaN-FETs boost chopper have been also developed based on the design. The SiC chopper achieved the efficiency of 97.8% and the power density of 12,8 W/cm3, and the GaN chopper accomplished 98.9% and 18.6 W/cm3 in the experiment. These results show the validity of the design and the availability of the proposed approach. The multi-converter approach enables the cost reduction of the modular power converters, and contributes to realizing the widespread use of power electronics converters in the future 380 V DC distribution system.
基金supported by State Grid Information and Telecommunication Group Scientific and Technological Innovation Project“Research on Power Digital Space Technology System and Key Technologies”(Program No.SGIT0000XMJS2310456).
文摘By integrating advanced digital technologies such as cloud computing and the Internet of Things in sensor measurement,information communication,and other fields,the digital DC distribution network can efficiently and reliably access DistributedGenerator(DG)and Energy Storage Systems(ESS),exhibiting significant advantages in terms of controllability and meeting requirements of Plug-and-Play(PnP)operations.However,during device plug-in and-out processes,improper systemparametersmay lead to small-signal stability issues.Therefore,before executing PnP operations,conducting stability analysis and adjusting parameters swiftly is crucial.This study introduces a four-stage strategy for parameter optimization to enhance systemstability efficiently.In the first stage,state-of-the-art technologies in measurement and communication are utilized to correct model parameters.Then,a novel indicator is adopted to identify the key parameters that influence stability in the second stage.Moreover,in the third stage,a local-parameter-tuning strategy,which leverages rapid parameter boundary calculations as a more efficient alternative to plotting root loci,is used to tune the selected parameters.Considering that the local-parameter-tuning strategy may fail due to some operating parameters being limited in adjustment,a multiparameter-tuning strategy based on the particle swarm optimization(PSO)is proposed to comprehensively adjust the dominant parameters to improve the stability margin of the system.Lastly,system stability is reassessed in the fourth stage.The proposed parameter-optimization strategy’s effectiveness has been validated through eigenvalue analysis and nonlinear time-domain simulations.
基金supported by the State Grid Shandong Electric Power Company Economic and Technical Research Institute Project(Grant No.SGSDJY00GPJS2100135).
文摘The DC distribution network system equipped with a large number of power electronic equipment exhibits weak damping characteristics and is prone to low-frequency and high-frequency unstable oscillations.The current interpretation of the oscillation mechanism has not been unified.Firstly,this paper established the complete statespace model of the distribution system consisting of a large number of electric vehicles,characteristic equation of the distribution network system is derived by establishing a state-space model,and simplified reduced-order equations describing the low-frequency oscillation and the high-frequency oscillation are obtained.Secondly,based on eigenvalue analysis,the oscillation modes and the influence of the key system parameters on the oscillation mode are studied.Besides,impacts of key factors,such as distribution network connection topology and number of dynamic loads,have been discussed to suppress oscillatory instability caused by inappropriate design or dynamic interactions.Finally,using the DC distribution example system,through model calculation and time-domain simulation analysis,the correctness of the aforementioned analysis is verified.
基金the National Natural Science Foundation of China(52177074).
文摘The escalating deployment of distributed power sources and random loads in DC distribution networks hasamplified the potential consequences of faults if left uncontrolled. To expedite the process of achieving an optimalconfiguration of measurement points, this paper presents an optimal configuration scheme for fault locationmeasurement points in DC distribution networks based on an improved particle swarm optimization algorithm.Initially, a measurement point distribution optimization model is formulated, leveraging compressive sensing.The model aims to achieve the minimum number of measurement points while attaining the best compressivesensing reconstruction effect. It incorporates constraints from the compressive sensing algorithm and networkwide viewability. Subsequently, the traditional particle swarm algorithm is enhanced by utilizing the Haltonsequence for population initialization, generating uniformly distributed individuals. This enhancement reducesindividual search blindness and overlap probability, thereby promoting population diversity. Furthermore, anadaptive t-distribution perturbation strategy is introduced during the particle update process to enhance the globalsearch capability and search speed. The established model for the optimal configuration of measurement points issolved, and the results demonstrate the efficacy and practicality of the proposed method. The optimal configurationreduces the number of measurement points, enhances localization accuracy, and improves the convergence speedof the algorithm. These findings validate the effectiveness and utility of the proposed approach.
基金supported by Key Natural Science Research Projects of Colleges and Universities in Anhui Province(No.2022AH051831).
文摘ADC distribution network is an effective solution for increasing renewable energy utilization with distinct benefits,such as high efficiency and easy control.However,a sudden increase in the current after the occurrence of faults in the network may adversely affect network stability.This study proposes an artificial neural network(ANN)-based fault detection and protection method for DC distribution networks.The ANN is applied to a classifier for different faults ontheDC line.The backpropagationneuralnetwork is used to predict the line current,and the fault detection threshold is obtained on the basis of the difference between the predicted current and the actual current.The proposed method only uses local signals,with no requirement of a strict communication link.Simulation experiments are conducted for the proposed algorithm on a two-terminal DC distribution network modeled in the PSCAD/EMTDC and developed on the MATLAB platform.The results confirm that the proposed method can accurately detect and classify line faults within a few milliseconds and is not affected by fault locations,fault resistance,noise,and communication delay.
文摘GaN （gallium nitride） buck-rectifier has been proposed to realize high power density ISOP （input series and output parallel）-IPOS （input parallel and output series） converter-based dc distribution system. The ultra-low loss bi-directional switch can be developed by the GaN power device because of the low on-resistance, the high-speed switching behavior and its own device structure. The buck-rectifier using the GaN bi-directional switches has the potential to achieve higher power density than the commonly utilized boost-rectifier. Availability of the GaN-HEMT （high electron mobility transistor） for the buck rectifier has been verified taking the theoretical limit of the on-resistance and the switching loss energy into account. Design consideration for a high power density buck-rectifier has been also conducted and the application effect of the GaN bidirectional switches has been evaluated quantitatively. The ISOP-IPOS converter-based dc （direct current） distribution system takes full advantage of the buck-rectifier and the rectifier using GaN devices contributes to realizing higher power density dc distribution system.
基金supported by the key technology project of China Southern Power Grid Corporation(GZKJXM20220041)partly by the National Key Research and Development Plan(2022YFE0205300).
文摘This paper presents an optimal operation method for embedded DC interconnections based on low-voltage AC/DC distribution areas(EDC-LVDA)under three-phase unbalanced compensation conditions.It can optimally determine the transmission power of the DC and AC paths to simultaneously improve voltage quality and reduce losses.First,considering the embedded interconnected,unbalanced power structure of the distribution area,a power flow calculation method for EDC-LVDA that accounts for three-phase unbalanced compensation is introduced.This method accurately describes the power flow distribution characteristics under both AC and DC power allocation scenarios.Second,an optimization scheduling model for EDC-LVDA under three-phase unbalanced conditions is developed,incorporating network losses,voltage quality,DC link losses,and unbalance levels.The proposed model employs an improved particle swarm optimization(IPSO)two-layer algorithm to autonomously select different power allocation coefficients for the DC link and AC section under various operating conditions.This enables embedded economic optimization scheduling while maintaining compensation for unbalanced conditions.Finally,a case study based on the IEEE 13-node system for EDC-LVDA is conducted and tested.The results show that the proposed optimal operation method achieves a 100%voltage compliance rate and reduces network losses by 13.8%,while ensuring three-phase power balance compensation.This provides a practical solution for the modernization and upgrading of low-voltage power grids.
基金supported by the National Natural Science Foundation of China(No.52207126)the Natural Science Foundation of Sichuan Province(No.2023NSFSC0296)the Joint Funds of the National Natural Science Foundation of China(No.U22B6006).
文摘DC series-parallel power flow controller(SP-PFC)is a highly efficient device to solve the problem of uncontrolled line current in the bipolar DC distribution system.However,its potential in fault current limiting is not fully explored.In this paper,a self-adaptive action strategy(SAAS)and a parameter optimization method of SP-PFC in bipolar DC distribution systems are proposed.Firstly,the common-and different-mode(CDM)equivalent circuits of the bipolar DC distribution system with SP-PFC in different fault stages are established,which avoids the line coupling inductance.Based on this,the influence of different parameters and line coupling inductance on the fault current limiting capability are investigated.It is found that the SP-PFC has the best fault current limiting capability when the capacitance and inductance of filter are inversely proportional.To realize the adaptability of fault current limiting capability under different fault severities,the SAAS of SP-PFC is proposed.The validity of the CDM equivalent circuits and parameter optimization method,and the effectiveness of the SAAS are verified by simulations and experiments.
文摘Optimal Power Flow (OPF) plays a crucial role in optimization and operation of the bipolar DC distribution network (Bi-DCDN). However, existing OPF models encounter difficulties in the power optimization of Bi-DCDNs due to the optimal power expressed as a product form, i.e., the product of voltage and current. Hence, this brief formulates the OPF problem of Bi-DCDNs using the branch flow model (BFM). The BFM employs power, instead of current, to account for the unique structure of Bi-DCDNs. Convex relaxation and linear approximation are sequentially applied to reformulate the BFM-based OPF, presenting it as a second-order cone programming (SOCP) problem. Further, the effectiveness of the proposed OPF model is verified in case studies. The numerical results demonstrate that the BFM-based OPF is a feasible and promising approach for Bi-DCDNs.
基金supported in part by the National Natural Science Foundation of China(No.52077017).
文摘The multi-voltage-level DC distribution network(MVL-DC-DN)is a promising network for efficiently integrat ing rapidly growing DC loads,and fast-growing load demand would bring a challenge to the MVL-DC-DN in terms of the maximum loadability.This paper considers the DC electric spring(DC-ES)as a novel candidate flexible resource for en hancing the maximum loadability of the MVL-DC-DN,and pro poses an evaluation method for the maximum loadability.First ly,with the consideration of device constraints,the impact that the DC-ES on the maximum loadability of the DC distribution network(DC-DN)is analyzed via a simplified equivalent cir cuit.Subsequently,the power flow(PF)model of an MVL-DCDN with DC-ESs is established.Finally,a method based on con tinuation power flow(CPF)for evaluating the maximum load ability of an MVL-DC-DN with DC-ESs is proposed.During the evaluation,limitations of the DC-ES and the DC transform er(DCT)are considered.The consideration of the practical con straints avoids the overestimation of the maximum loadability.The case study verifies the effectiveness of the proposed method.
基金supported by the National Basic Research Program of China("973" Project)(Grant No.2012CB215206)the National Natural Science Foundation of China(Grant Nos.51407067&51222703)the "111" Project of China(Grant No.B08013)
文摘A novel single-ended online fault location algorithm is investigated for DC distribution networks. The proposed algorithm calculates the fault distance based on the characteristics of the voltage resonance. The Prony's method is introduced to extract the characteristics. A novel method is proposed to solve the pseudo dual-root problem in the calculation process. The multiple data windows are adopted to enhance the robustness of the proposed algorithm. An index is proposed to evaluate the accuracy and validity of the results derived from the various data windows. The performances of the proposed algorithm in different fault scenarios were evaluated using the PSCAD/EMTDC simulations. The results show that the algorithm can locate the faults with transient resistance using the 1.6 ms data of the DC-side voltage after a fault inception and offers a good precision.
基金This work is supported by National Key R&D Program(2018YFB0904600).
文摘With the development of power electronic technologies and distributed power generation,DC distribution networks attract increasing attention due to their various advantages compared with traditional AC distribution networks.However,DC fault protection is one of the major issues in DC distribution networks.To improve their reliability and protect the semiconductor devices under DC faults,a current-limiting and energy-transferring DC circuit breaker topology is proposed in this paper.By applying passive components and thyristors,the proposed topology is capable of quickly limiting the fault current and transferring the faulty energy.The working principle,mathematical model and parameter designing method of the proposed topology are presented in this paper.The simulation results verify that the proposed DC circuit breaker could effectively limit the fault current and quickly interrupt the fault current.Cost and conduction power loss evaluation proves the practicality of the proposed topology in medium-voltage DC distribution networks.
基金This work was supported in part by the National Nature Science Foundation of China(51977142)。
文摘The concept of a flexible power electronics substation(FPES)was first applied in the Zhangbei DC distribution network demonstration project.As a multi-port power electronics transformer(PET)with different AC and DC voltage levels,the FPES has adopted a novel topology integrating modular multilevel converter(MMC)and four-winding medium frequency transformer(FWMFT)based multiport DC-DC converter,which can significantly reduce capacitance in each sub-module(SM)of a MMC and also save space and cost.In this paper,in order to accelerate speed of electromagnetic transient(EMT)simulations of FPES based hybrid AC/DC distribution systems,an averaged-value model(AVM)is proposed for efficient and accurate representation of FPES.Assume that all SM capacitor voltages are perfectly balanced in the MMC,then the MMC behavior can be modeled using controlled voltage sources based on modulation voltages from control systems.In terms of the averaged current transfer characteristics among the windings of the FWMFT,we consider that all multiport DC-DC converters are controlled with the same dynamics,a lumped averaged model using controlled current and voltage sources has been developed for these four-port DC-DC converters connected to the upper or lower arms of the MMC.The presented FPES AVM model has been tested and validated by comparison with a detailed IGBT-based EMT model.Results show that the AVM is significantly more efficient while maintaining its accuracy in an EMT simulation.
基金supported by the National Natural Science Foundation of China(No.51877174)。
文摘As the structures of multiple branch lines(MBLs)will be widely applied in the future flexible DC distribution network,there is a urgent need for improving system reliability by tackling the frequent non-permanent pole-to-pole(P-P)fault on distribution lines.A novel fault restoration strategy based on local information is proposed to solve this issue.The strategy firstly splits a double-ended power supply network into two single-ended power supply networks through the timing difference characteristics of a hybrid direct current circuit breaker(HDCCB)entering the recloser.Then,a method based on the characteristic of the transient energy of fault current is proposed to screen the faulty branch line in each single-ended power supply network.Also,a four-terminal flexible DC distribution network with MBLs is constructed on PSCAD to demonstrate the efficacy of the proposed strategy.Various factors such as noise,fault location,and DC arc equivalent resistance are considered in the simulation model for testing.Test results prove that the proposed strategy for fault restoration is effective,and features high performance and scalability.
基金supported by Fundamental Research Funds for the Central Universities(No.2019JBM057)。
文摘Due to the advantages such as low line cost,low transmission loss,and high power supply reliability,DC distribution networks have become the main development trend for future distribution networks.In this paper,a typical DC distribution network with multiple voltage levels is considered as a research object.It is proposed that the interface converters between DC buses with different voltage levels be implemented through the series-parallel combination of full-bridge LLC resonant converters.To realize the decentralized self-discipline control of DC voltage under various working conditions,different slack buses are prepared according to the voltage ranges of the DC buses,and the voltage regulation modes of the DC distribution network are divided into main voltage regulation mode,backup voltage regulation mode,and off-grid voltage droop regulation mode.By introducing a voltage coefficient related to DC voltage deviation as a basis for mode switching,the voltage fluctuations caused by slow switching between control modes in the method of traditional voltage margin control is reduced,facilitating fast and smooth switching between different voltage regulation modes.Finally,a simulation model for DC distribution networks is constructed utilizing MATLAB/Simulink.Simulation results verify the effectiveness and feasibility of the proposed voltage regulation modes and switching methods for DC distribution networks.Finally,an experimental platform is also constructed to verify the feasibility of the mode switching method proposed in this paper.
基金supported by the National Natural Science Foundation of China (No. 51877136)the Shanghai Committee of Science and Technology (No. 19DZ1205403)the Inner Mongolia Autonomous Region Committee of Science and Technology (No. 2020GG0299)。
文摘The bipolar low-voltage DC(LVDC) distribution system has become a prospective solution to better integration of renewables and improvement of system efficiency and reliability. However, it also faces the challenge of power and voltage imbalance between two poles. To solve this problem, an interface converter with bipolar asymmetrical operating capabilities is applied in this paper. The steady-state models of the bipolar LVDC distribution system equipped with this interface converter in the gridconnected mode and off-grid mode are analyzed. A control scheme based on DC offset injection at the secondary side of the interface converter is proposed, enabling the bipolar LVDC distribution system to realize the unbalanced power transfer between two poles in the grid-connected mode and maintain the inherentpole voltage balance in the off-grid mode. Furthermore, this paper also proposes a primary-side DC offset injection control scheme according to the analysis of the magnetic circuit model, which can eliminate the DC bias flux caused by the secondaryside DC offset. Thereby, the potential core magnetic saturation and overcurrent issues can be prevented, ensuring the safety of the interface converter and distribution system. Detailed simulations based on the proposed control scheme are conducted to validate the function of power and voltage balance under the operation conditions of different DC loads.
基金This work was supported in part by FLEXIS.FLEXIS is part-funded by the European Regional Development Fund(ERDF),through the Welsh Government(WEFO case number 80836)The work was also supported in part by the UK EPSRC Sustainable urban power supply through intelligent control and enhanced restoration of AC/DC networks,under Grant EP/T021985/1in part by the National Nature Science Foundation of China(Grant No.52272403)。
文摘DC technologies will be essential building blocks for future DC distribution networks.As in any DC system,these networks will face crucial threats imposed by short-circuit DC faults.Protection is thus of great interest,and it will likely rely on DC circuit breakers(DCCBs).Among available configurations,Z-source solid-state circuit breakers(Z-SSCBs)are promising candidates for protecting low and medium-voltage distribution networks,as well as DC equipment due to their structural and control simplicity and low cost.In this paper,start-ofthe-art of Z-SSCBs topologies is reviewed.To set the context,the use of DC technologies for grid integration of renewables,DC power transmission,and the main types of DCCBs to protect DC transmission and distribution corridors are discussed.The Z-SSCB topologies are then classified into unidirectional and bidirectional.Advantages and disadvantages of different configurations are compared and analyzed based on existing research.Finally,a perspective on the future development of Z-SSCBs is discussed and potential challenges are elucidated.
