The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key ...The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key role.In this work,X70 steels with different start cooling temperatures were prepared through thermo-mechanical control process.The quasi-polygonal ferrite(QF),granular bainite(GB),bainitic ferrite(BF)and martensite-austenite constituents were formed at the start cooling temperatures of 780℃(C1),740℃(C2)and 700℃(C3).As start cooling temperature decreased,the amount of GB decreased,the microstructure of QF and BF increased.Microstructure characteristics of the three samples,such as high-angle grain boundaries(HAGBs),MA constituents and crystallographic orientation,also varied with the start cooling temperatures.C2 sample had the lowest DBTT value(−86℃)for its highest fraction of HAGBs,highest content of<110>oriented grains and lowest content of<001>oriented grains parallel to TD.The high density of{332}<113>and low density of rotated cube{001}<110>textures also contributed to the best impact toughness of C2 sample.In addition,a modified model was used in this paper to quantitatively predict the approximate DBTT value of steels.展开更多
The toughness of ferritic steels is influenced by the grain size distribution, second phase, precipitates and coarse inclusions. In this work an examination of the effect of coarse TiN particles （〉0.5 μm） and ferr...The toughness of ferritic steels is influenced by the grain size distribution, second phase, precipitates and coarse inclusions. In this work an examination of the effect of coarse TiN particles （〉0.5 μm） and ferrite grain size on the Charpy impact transition temperature in high strength low alloyed steels has been carried out. Steels with high Ti content （up to 0.045 wt%）, have been heat-treated and furnace cooled to obtain a ferrite-pearlite microstructure with different ferrite grain sizes. Coarse TiN particle size and ferrite grain size distributions have been measured and Charpy impact testing has been carried out. Scanning electron microscopy （SEM） analysis has been used to measure the grain boundary carbide thickness and to determine if the coarse TiN particles are acting as cleavage initiation sites by fractographic analysis. The Charpy ductile-brittle transition temperatures （DBTT） have been predicted using standard literature equations, and compared to the measured values. The relationship between the ferrite grain size and coarse TiN particle size and number density in terms of whether the coarse TiN particles act as effective cleavage initiation sites is discussed in this paper.展开更多
In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were...In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were fabricated by varying RE addition and the cooling process at the same time.Three microstructures with different features for a low C high Nb microalloyed high-strength pipeline steel and the corresponding mechanical properties were investigated.The results showed that even in the ultra-cleaned steel with O and S contents less than 10 ppm,the addition of RE would still cause an increase in the volume fraction of inclusions consisting of complicated RE oxysulfide and RE sulfide.More inclusions formed in the 112 ppm RE steel were harmful to the low temperature toughness,while few inclusions formed in the 47 ppm RE steel had almost no influence on the low temperature toughness.The two RE additions had no effect on strength of the steels.As the finishing cooling temperature was increased and the cooling rate was decreased within a certain range,the volume fractions of polygonal ferrite and quasi-polygonal ferrite as well as the number density and size of martensite–austenite islands were increased.Under such combined effect,the strength of the steels had almost no change.As the finishing cooling temperature was increased from 481 to 584℃and the cooling rate was reduced from 20 to 13℃/s,for the steel with 112 ppm addition of RE,there was an obvious decrease in the low temperature toughness.The reduced value(about 33 J)of the USE of steel consisted of two parts including the influence(about 18 J)of more inclusions formed due to 112 ppm addition of RE and the eff ect(about 15 J)of the lower high-angle grain boundaries.展开更多
The effects of two alloying elements,i.e.,yttrium(Y)and zirconium(Zr),on the inclusion,microstructure,tensile property and impact toughness of reduced activation ferritic/martensitic(RAFM)steel are analyzed.The size a...The effects of two alloying elements,i.e.,yttrium(Y)and zirconium(Zr),on the inclusion,microstructure,tensile property and impact toughness of reduced activation ferritic/martensitic(RAFM)steel are analyzed.The size and number of particles were determined by optical microscopy,and the particle types were examined by scanning electron microscopy.The size of?20% and?85% of the inclusions lied in the range of 0.5-1.0μm and 0.5-3.0μm,respectively.In Y-and Y-Zr-containing specimens,the density of the fine inclusions,with a size less than 0.5μm,was found to be 1.06×10^17 and 9.82×10^16 m^-3.respectively.All specimens were normalized at 1323 K for 30 min and tempered at 923 and 1023 K for 90 min,resulting in the formation of tempered martensite with M23C6 carbides and MX precipitates.Zr-containing RAFM steel tempered at 923 K formed M23C6 carbides and nano-sized carbides with Zr,conferring superior strength balance and impact toughness.The yield strength of alloy reached 695 MPa,and a low ductile-brittle transition temperature of 238 K was maintained.展开更多
基金Project(2018XK2301) supported by the Change-Zhu-Tan National Independent Innavation Demonstration Zone Special Program,China。
文摘The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key role.In this work,X70 steels with different start cooling temperatures were prepared through thermo-mechanical control process.The quasi-polygonal ferrite(QF),granular bainite(GB),bainitic ferrite(BF)and martensite-austenite constituents were formed at the start cooling temperatures of 780℃(C1),740℃(C2)and 700℃(C3).As start cooling temperature decreased,the amount of GB decreased,the microstructure of QF and BF increased.Microstructure characteristics of the three samples,such as high-angle grain boundaries(HAGBs),MA constituents and crystallographic orientation,also varied with the start cooling temperatures.C2 sample had the lowest DBTT value(−86℃)for its highest fraction of HAGBs,highest content of<110>oriented grains and lowest content of<001>oriented grains parallel to TD.The high density of{332}<113>and low density of rotated cube{001}<110>textures also contributed to the best impact toughness of C2 sample.In addition,a modified model was used in this paper to quantitatively predict the approximate DBTT value of steels.
文摘The toughness of ferritic steels is influenced by the grain size distribution, second phase, precipitates and coarse inclusions. In this work an examination of the effect of coarse TiN particles （〉0.5 μm） and ferrite grain size on the Charpy impact transition temperature in high strength low alloyed steels has been carried out. Steels with high Ti content （up to 0.045 wt%）, have been heat-treated and furnace cooled to obtain a ferrite-pearlite microstructure with different ferrite grain sizes. Coarse TiN particle size and ferrite grain size distributions have been measured and Charpy impact testing has been carried out. Scanning electron microscopy （SEM） analysis has been used to measure the grain boundary carbide thickness and to determine if the coarse TiN particles are acting as cleavage initiation sites by fractographic analysis. The Charpy ductile-brittle transition temperatures （DBTT） have been predicted using standard literature equations, and compared to the measured values. The relationship between the ferrite grain size and coarse TiN particle size and number density in terms of whether the coarse TiN particles act as effective cleavage initiation sites is discussed in this paper.
基金financially supported by the National Key Research and Development Program of China(Grant No.2017YFB0304901)。
文摘In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were fabricated by varying RE addition and the cooling process at the same time.Three microstructures with different features for a low C high Nb microalloyed high-strength pipeline steel and the corresponding mechanical properties were investigated.The results showed that even in the ultra-cleaned steel with O and S contents less than 10 ppm,the addition of RE would still cause an increase in the volume fraction of inclusions consisting of complicated RE oxysulfide and RE sulfide.More inclusions formed in the 112 ppm RE steel were harmful to the low temperature toughness,while few inclusions formed in the 47 ppm RE steel had almost no influence on the low temperature toughness.The two RE additions had no effect on strength of the steels.As the finishing cooling temperature was increased and the cooling rate was decreased within a certain range,the volume fractions of polygonal ferrite and quasi-polygonal ferrite as well as the number density and size of martensite–austenite islands were increased.Under such combined effect,the strength of the steels had almost no change.As the finishing cooling temperature was increased from 481 to 584℃and the cooling rate was reduced from 20 to 13℃/s,for the steel with 112 ppm addition of RE,there was an obvious decrease in the low temperature toughness.The reduced value(about 33 J)of the USE of steel consisted of two parts including the influence(about 18 J)of more inclusions formed due to 112 ppm addition of RE and the eff ect(about 15 J)of the lower high-angle grain boundaries.
基金National Natural Science Foundation of China(Nos.51874081 and 51574063)Fundamental Research Funds for the Central Universities(N150204012).
文摘The effects of two alloying elements,i.e.,yttrium(Y)and zirconium(Zr),on the inclusion,microstructure,tensile property and impact toughness of reduced activation ferritic/martensitic(RAFM)steel are analyzed.The size and number of particles were determined by optical microscopy,and the particle types were examined by scanning electron microscopy.The size of?20% and?85% of the inclusions lied in the range of 0.5-1.0μm and 0.5-3.0μm,respectively.In Y-and Y-Zr-containing specimens,the density of the fine inclusions,with a size less than 0.5μm,was found to be 1.06×10^17 and 9.82×10^16 m^-3.respectively.All specimens were normalized at 1323 K for 30 min and tempered at 923 and 1023 K for 90 min,resulting in the formation of tempered martensite with M23C6 carbides and MX precipitates.Zr-containing RAFM steel tempered at 923 K formed M23C6 carbides and nano-sized carbides with Zr,conferring superior strength balance and impact toughness.The yield strength of alloy reached 695 MPa,and a low ductile-brittle transition temperature of 238 K was maintained.
