Polycrystalline diamond compact(PDC)cutters and carbon steel were brazed by AgCuInTi filler metal under vacuum condition.The effects of brazing temperature on the wettability of base metal and shear strength of joints...Polycrystalline diamond compact(PDC)cutters and carbon steel were brazed by AgCuInTi filler metal under vacuum condition.The effects of brazing temperature on the wettability of base metal and shear strength of joints were investigated.Besides,the joint's interface microstructure,composition,and phases were analyzed.Results show that the AgCuInTi filler metal exerts a good wetting effect to the surface of cemented carbide and steel.With the increase in brazing temperature,the wetting angle decreases and the spreading area increases.The suitable temperature for vacuum brazing of PDC cutters is 770℃,and the maximum shear strength is 228 MPa at this temperature.展开更多
The cutter layout of a full-face tunnel boring machine(TBM)directly affects its tunneling efficiency.The revolving diameter of the center cutter is small,and the double-edged design results in its rock breaking mechan...The cutter layout of a full-face tunnel boring machine(TBM)directly affects its tunneling efficiency.The revolving diameter of the center cutter is small,and the double-edged design results in its rock breaking mechanism and force characteristics being significantly different from those of the single-edged cutter.The gage cutter is installed on the transition arc of the cutterhead,and the installation inclination complicates its movement and force.In this paper,by taking sandstone as the research object,the composite rock breaking models of the center cutter group and the gage cutter group of a compound TBM are separately established based on the three-dimensional particle discrete element method.The numerical models are verified by comparing results with the full-scale rotary cutting laboratory test.From the view point of the force characteristics of a single cutter,the propagation of rock cracks between adjacent cutters,the overall mechanical properties of the cutterhead,the load characteristics and layout form of the double-edged center cutter,and the installation angle range of the gage cutter were studied.Results demonstrate that the use of a cross-shaped center cutter layout can reduce the force of a single cutter ring and the overall load of the cutterhead,which is conducive to TBM stability during tunneling.Therefore,it is recommended that a cross-shaped layout for the double-edged center cutter of a rock formation compound TBM should be used.To improve the stability and service life of the cutter,we recommend setting the installation angle of the innermost gage cutter of the rock formation compound TBM to about 9°,and the installation angle of the outermost gage cutter should not exceed 70°.展开更多
During shield tunneling in highly abrasive formations such as sand–pebble strata,nonuniform wear of shield cutters is inevitable due to the different cutting distances.Frequent downtimes and cutter replacements have ...During shield tunneling in highly abrasive formations such as sand–pebble strata,nonuniform wear of shield cutters is inevitable due to the different cutting distances.Frequent downtimes and cutter replacements have become major obstacles to long-distance shield driving in sand–pebble strata.Based on the cutter wear characteristics in sand–pebble strata in Beijing,a design methodology for the cutterhead and cutters was established in this study to achieve uniform wear of all cutters by the principle of frictional wear.The applicability of the design method was verified through three-dimensional simulations using the engineering discrete element method.The results show that uniform wear of all cutters on the cutterhead could be achieved by installing different numbers of cutters on each trajectory radius and designing a curved spoke with a certain arch height according to the shield diameter.Under the uniform wear scheme,the cutter wear coefficient is greatly reduced,and the largest shield driving distance is increased by approximately 47%over the engineering scheme.The research results indicate that the problem of nonuniform cutter wear in shield excavation could be overcome,thereby providing guiding significance for theoretical innovation and construction of long-distance shield excavation in highly abrasive strata.展开更多
Studies to date have failed to consider gage disc cutters’variable cutting depth and the constraints of cutter-head welds,and have ignored the coupling mechanism between the profile of the full-face rock tunnel-borin...Studies to date have failed to consider gage disc cutters’variable cutting depth and the constraints of cutter-head welds,and have ignored the coupling mechanism between the profile of the full-face rock tunnel-boring machine(TBM)cutter-head and the assembled radius layout of the disc cutters.To solve these problems,an adaptive design method for studying cutter layout was proposed.Taking the bearing stress of the outermost gage disc cutter as an index,the profile of the cutter-head was determined.Using a genetic algorithm and based on the principles of equal life and equal wear,the assembled radii of the cutters were optimally designed.Boundary conditions of non-interference between the cutters,manholes,muck buckets and welding lines were given when a star layout pattern was used on cutters.The cutter-head comprehensive evaluation model was established by adopting relative optimization improvement degree of evaluation indices to achieve dimensional consistency.Exemplifying the MB264-311-8030 mm tape TBM cutter-head,the calculations show that compared with the original layout scheme,among the 51 disc cutters,the largest gap of the cutters’assembled radiuses is only 25.8 mm,which is 0.64%of the cutter-head’s radius and is negligible.The cutter-head’s unbalanced radial force decreases by 62.41%,the overturning moment decreases by 33.22%,and the cutter group’s centroid shift increases by only 18.48%.Each index is better than or approximately equal to the original cutter-head layout scheme,and the equivalent stress and deformation are both smaller;these results fully verify the feasibility and effectiveness of the method.展开更多
In order to develop a rotary percussive bit with diamond enhanced cutters assisted by high pressure water jets, it is necessary to study the damage mechanism and the penetration properties of PDC cutters subject to di...In order to develop a rotary percussive bit with diamond enhanced cutters assisted by high pressure water jets, it is necessary to study the damage mechanism and the penetration properties of PDC cutters subject to different impact load level and rock types. Therefore the impact experiments of the single PDC cutters with different attack angles in four rocks: black basalt, Missouri red granite, Halston limestone, and a very soft (Roubidoux) sandstone were carried out, and the effects of rake angles of PDC cutters on both the penetration and impact resistance of PDC cutters have been discussed in detail. Test results show that a PDC insert can withstand a very strong impact in compression but is easily damaged by impact shearing, the PDC cutters are more easily damaged by shearing if the attack angles are relatively small, the 45? PDC cutters have the least penetration resistance among the cutters tested. Thus it is suggested that the attack angles of PDC cutters should be larger than 30? for bits which must withstand impact from a hammer.展开更多
Copper and zinc were recovered from waste diamond cutters through leaching with an ammonia–ammonium sulfate system and air as an oxidant. The effects of experimental parameters on the leaching process were investigat...Copper and zinc were recovered from waste diamond cutters through leaching with an ammonia–ammonium sulfate system and air as an oxidant. The effects of experimental parameters on the leaching process were investigated, and the potential–pH(E–pH) diagrams of Cu–NH_3–SO_4^(2-)–H_2O and Zn–NH_3–SO_4^(-2)–H_2O at 25°C were drawn. Results showed that the optimal parameters for the leaching reaction are as follows: reaction temperature, 45°C; leaching duration, 3 h; liquid-to-solid ratio, 50:1(mL/g); stirring speed, 200 r/min; ammonia concentration, 4.0 mol/L; ammonium sulfate concentration, 1.0 mol/L; and air flow rate, 0.2 L/min. The results of the kinetics study indicated that the leaching is controlled by the surface chemical reaction at temperatures below 35°C, and the leaching is controlled by diffusion through the product layer at temperatures above 35°C.展开更多
The concept of cutting platform is proposed and realized based on the latest two step automated tape laying (Two step ATL)technology,which separates prepreg cutting process from tape laying to improve productivity for...The concept of cutting platform is proposed and realized based on the latest two step automated tape laying (Two step ATL)technology,which separates prepreg cutting process from tape laying to improve productivity for large parts with small features.Two step ATL is more efficient than conventional layup because ply patches are pre cut in a separate operation.The concept of the prepreg tape cutting experimental platform with two cutters is introduced.Further,based on the automatic tape laying trajectory planning software,a two cutter cutting algorithm is proposed.Cutting experiments are reported to validate both the concept of cutting platform and cutting algorithm.展开更多
Attempts to minimize energy consumption of a tunnel boring machine disc cutter during the process of fragmentation have largely focused on optimizing disc- cutter spacing, as determined by the minimum specific energy ...Attempts to minimize energy consumption of a tunnel boring machine disc cutter during the process of fragmentation have largely focused on optimizing disc- cutter spacing, as determined by the minimum specific energy required for fragmentation; however, indentation tests showed that rock deforms plastically beneath the cutters. Equations for thrust were developed for both the traditional, popularly employed disc cutter and anew design based on three-dimensional theory. The respective energy consumption for penetration, rolling, and side-slip fragmentations were obtained. A change in disc-cutter fragmentation angles resulted in a change in the nature of the interaction between the cutter and rock, which lowered the specific energy of fragmentation. During actual field excavations to the same penetration length, the combined energy consumption for fragmentation using the newly designed cutters was 15% lower than that when using the traditional design. This paper presents a theory for energy saving in tunnel boring machines. Investigation results showed that the disc cutters designed using this theory were more durable than traditional designs, and effectively lowered the energy consumption.展开更多
Wear is a major factor of disc cutters’ failure. No current theory offers a standard for the prediction of disc cutter wear yet. In the field the wear prediction method commonly used is based on the excavation length...Wear is a major factor of disc cutters’ failure. No current theory offers a standard for the prediction of disc cutter wear yet. In the field the wear prediction method commonly used is based on the excavation length of tunnel boring machine（TBM） to predict the disc cutter wear and its wear law, considering the location number of each disc cutter on the cutterhead（radius for installation）; in theory, there is a prediction method of using arc wear coefficient. However, the preceding two methods have their own errors, with their accuracy being 40% or so and largely relying on the technicians’ experience. Therefore, radial wear coefficient, axial wear coefficient and trajectory wear coefficient are defined on the basis of the operating characteristics of TBM. With reference to the installation and characteristics of disc cutters, those coefficients are modified according to penetration, which gives rise to the presentation of comprehensive axial wear coefficient, comprehensive radial wear coefficient and comprehensive trajectory wear coefficient. Calculation and determination of wear coefficients are made with consideration of data from a segment of TBM project（excavation length 173 m）. The resulting wear coefficient values, after modification, are adopted to predict the disc cutter wear in the follow-up segment of the TBM project（excavation length of 5621 m）. The prediction results show that the disc cutter wear predicted with comprehensive radial wear coefficient and comprehensive trajectory wear coefficient are not only accurate（accuracy 16.12%） but also highly congruous, whereas there is a larger deviation in the prediction with comprehensive axial wear coefficient（accuracy 41%, which is in agreement with the prediction of disc cutters’ life in the field）. This paper puts forth a new method concerning prediction of life span and wear of TBM disc cutters as well as timing for replacing disc cutters.展开更多
Predicting the cutter consumption and the exact time to replace the worn-out cutters in tunneling projects constructed with tunnel boring machine(TBM) is always a challenging issue. In this paper, we focus on the anal...Predicting the cutter consumption and the exact time to replace the worn-out cutters in tunneling projects constructed with tunnel boring machine(TBM) is always a challenging issue. In this paper, we focus on the analyses of cutter motion in the rock breaking process and trajectory of rock breaking point on the cutter edge in rocks. The analytical expressions of the length of face along which the breaking point moves and the length of spiral trajectory of the maximum penetration point are derived. Through observation of rock breaking process of disc cutters as well as analysis of disc rock interaction, the following concepts are proposed: the arc length theory of predicting wear extent of inner and center cutters, and the spiral theory of predicting wear extent of gage and transition cutters. Data obtained from5621 m-long Qinling tunnel reveal that among 39 disc cutters, the relative errors between cumulatively predicted and measured wear values for nine cutters are larger than 20%, while approximately 76.9% of total cutters have the relative errors less than 20%. The proposed method could offer a new attempt to predict the disc cutter's wear extent and changing time.展开更多
Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact c...Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact cutting force model that can accurately reflect a true cutting process. However, there is little research on the prediction of chatter stablity in milling. Based on the generalized mathematical model of inserted cutters introduced by ENGIN, an improved geometrical, mechanical and dynamic model for the vast variety of inserted cutters widely used in engineering applications is presented, in which the average directional cutting force coefficients are obtained by means of a numerical approach, thus leading to an analytical determination of stability lobes diagram (SLD) on the axial depth of cut. A new kind of SLD on the radial depth of cut is also created to satisfy the special requirement of inserted cutter milling. The corresponding algorithms used for predicting cutting forces, vibrations, dimensional surface finish and stability lobes in inserted cutter milling under different cutting conditions are put forward. Thereafter, a dynamic simulation module of inserted cutter milling is implemented by using hybrid program of Matlab with Visual Basic. Verification tests are conducted on a vertical machine center for Aluminum alloy LC4 by using two different types of inserted cutters, and the effectiveness of the model and the algorithm is verified by the good agreement of simulation result with that of cutting tests under different cutting conditions. The proposed model can predict the cutting process accurately under a variety of cutting conditions, and a high efficient and chatter-free milling operation can be achieved by a cutting condition optimization in industry applications.展开更多
Titanium alloy has been applied in the field of aerospace manufacturing for its high specific strength and hardness.Nonetheless,these properties also cause general problems in the machining,such as processing ineffici...Titanium alloy has been applied in the field of aerospace manufacturing for its high specific strength and hardness.Nonetheless,these properties also cause general problems in the machining,such as processing inefficiency,serious wear,poor workpiece face quality,etc.Aiming at the above problems,this paper carried out a comparative experimental study on titanium alloy milling based on the CAMCand BEMC.The variation law of cutting force and wear morphology of the two tools were obtained,and the wear mechanism and the effect of wear on machining quality were analyzed.The conclusion is that in contrast with BEMC,under the action of cutting thickness thinning mechanism,the force of CAMC was less,and its fluctuation was more stable.The flank wear was uniform and near the cutting edge,and the wear rate was slower.In the early period,the wear mechanism of CAMC was mainly adhesion.Gradually,oxidative wear also occurred with milling.Furthermore,the surface residual height of CAMC was lower.There is no obvious peak and trough accompanied by fewer surface defects.展开更多
A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with diff...A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with different spacings. A continuous-discontinuous coupling numerical method based on zero-thickness cohesive elements is developed to simulate rock breaking using double cutters. The process, mechanism,and characteristics of rock breaking are comprehensively analyzed from five aspects: peak force, breaking form, breaking efficiency, crack mode, and breaking degree. The results show that under the penetrating action of cutters, dense cores are formed due to shear failure under respective cutters. The tensile cracks propagate in the rock, and then rock chips form with increasing penetration depth. When the cutter spacing is increased from 10 to 80 mm, the peak force gradually increases, the rock breaking range increases first and then decreases, the specific energy decreases first and then rises, and the breaking coefficient of intermediate rock decreases from 0.955 to 0.788. The area of rock breaking is positively correlated with the length of the tensile crack. Furthermore, the length of the tensile crack accounts for 14.4%–33.6% of the total crack length.展开更多
How to generate rake faces of nonconventional milling cutters (NCMC) with constant spiral angled and normal rake angled edges on NC machine tools is presented by use of a blunt cup grinder or a cup milling cutter. Mot...How to generate rake faces of nonconventional milling cutters (NCMC) with constant spiral angled and normal rake angled edges on NC machine tools is presented by use of a blunt cup grinder or a cup milling cutter. Motion functions of the NC machining system are mathematically deduced and exam- ed by a experiment. The research will provide theoretical and practical guidance for machining noncon- ventional tools on NC machine tools.展开更多
Power generators and chemical engineering compressors include heavy and large centrifugal impellers. To produce these impellers in high-speed machining, a 4?-axis milling machine(or a 4-axis machine plus an indexing t...Power generators and chemical engineering compressors include heavy and large centrifugal impellers. To produce these impellers in high-speed machining, a 4?-axis milling machine(or a 4-axis machine plus an indexing table) is often used in the industry, which is more rigid than a5-axis milling machine. Since impeller blades are designed with complex B-spline surfaces and impeller channels spaces vary significantly, it is more efficient to use multiple cutters as large as possible to cut a channel in sections and a blade surface in patches, instead of only using a small cutter to machine a whole blade and a channel. Unfortunately, no approach has been established to automatically calculate the largest diameters of cutters and their paths, which include the indexing table angles. To address this problem, an automated and optimization approach is proposed. Based on the structure of a 4?-axis machine, a geometric model for a cutter gouging/interfering the impeller is formulated, and an optimization model of the cutter diameter in terms of the indexing table angle is established at a cutter contact(CC) point on a blade surface. Then, the diameters of the tools,their orientations, and the indexing table angles are optimized, and each tool's paths are generated for machining its corresponding impeller section. As a test, an impeller is efficiently machined with these tools section by section; thus, this approach is valid. It can be directly used in the industry to improve efficiency of machining centrifugal impellers.展开更多
The disc cutters of tunnel boring machine(TBM) are installed with different polar angles. This causes the cutting depth difference between adjacent disc cutters on the tunnel face. A rock-cutting model was established...The disc cutters of tunnel boring machine(TBM) are installed with different polar angles. This causes the cutting depth difference between adjacent disc cutters on the tunnel face. A rock-cutting model was established to study the rock fragmentation law between adjacent disc cutters with different polar angles based on particle flow code(PFC). The influence of polar angle of adjacent disc cutters on rock cracks and stresses under different cutter spacing and penetration was studied. Research shows that polar angle difference leads to the discontinuity of rock-fragmentation process by adjacent cutters. The effect of rock-fragmentation is influenced by the cutting depth difference between adjacent cutters. The effect of rock-fragmentation performed best, meanwhile large rock blocks were flaked when the difference of cutting depth is half of the penetration. Too large or small difference of the cutting depth will cause high specific energy consumption of rock fragmentation. The specific energy consumption is relatively small when the difference of cutting depth is half of the penetration.展开更多
Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the...Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the effects of discontinuities on cutting characteristics and cutting efficiency. In laboratory tests, five propagation patterns of radial cracks are observed. And in the numerical tests, firstly, it is similar to laboratory tests that cracks ahead of cutters mainly initiate from the crushed zone, and some minor cracks will initiate from joints. The cracks initiating from crushed zones will run through the thinner joints while they will be held back by thick joints. Cracks tend to propagate towards the tips of embedded cracks, and minor cracks will initiate from the tips of embedded cracks, which may result in the decrease of specific area, and disturbing layers play as ‘screens', which will prevent cracks from developing greatly. The peak penetration forces, the consumed energy in the penetration process and the uniaxial compression strength will decrease with the increase of discontinuities. The existence of discontinuities will result in the decrease of the cutting efficiency when the spacing between cutters is 70 mm. Some modifications should be made to improve the efficiency when the rocks containing groups of discontinuities are encountered.展开更多
Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000)...Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000) designed and manufactured in Central South University(China). Results are obtained by performing analysis on the fracture scopes of cement and granite plates,the characteristics of cutting force in cutting processes and the cutting efficiency. Firstly, the increase of latitude fracture scope and the decrease of longitude fracture scope are both more notable in the tests conducted on cement plates subjected to the increasing confining stresses; secondly, the increase tendency of peak penetration forces obtained from tests conducted on granite plates is more obvious, however, the increase tendencies of average penetration forces achieved from cement and granite plates are close to each other; thirdly, the cutting efficiency could be improved by increasing the spacing between cutters when the confining stress which acts on soft and hard rock increases in a certain degree, and the cutting efficiency of soft rock is more sensitive to the varying confining stresses.展开更多
The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts a...The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts and the maximum tangential stress criterion are used to investigate the micro crack propagation and its direction underneath the excavating discs. A higher order displacement discontinuity method with quadratic displacement discontinuity elements is used to estimate the stress intensity factors near the crack tips. Rock cutting mechanisms under single and double type discs are simulated by the proposed numerical method.The main purposes of the present modeling are to simulate the chip formation process of indented rocks by single and double discs.The effects of specific disc parameters(except speed) on the thrust force Ft, the rolling force Fr, and the specific energy ES are investigated. It has been shown that the specific energy(energy required to cut through a unit volume of rock) of the double disc is less than that of the single disc. Crack propagation in rocks under disc cutters is numerically modeled and the optimum ratio of disc spacing S to penetration depth Pd(i.e. S/Pd ratio) of about 10 is obtained, which is in good agreement with the theoretical and experimental results cited in the literature.展开更多
基金National Natural Science Foundation of China(52075551,52271045,51975469)Supported by State Key Laboratory of Advanced Welding and Joining(AWJ-22M09)+2 种基金Supported by State Key Laboratory of Advanced Brazing Filler Metals and Technology(SKLABFMT201904)Key Research and Development Program of Shaanxi Province(2022GY-224)Innovative Talent Recommendation Program(Youth Science and Technology New Star Project)of Shaanxi Province(2020 KJX X-045)。
文摘Polycrystalline diamond compact(PDC)cutters and carbon steel were brazed by AgCuInTi filler metal under vacuum condition.The effects of brazing temperature on the wettability of base metal and shear strength of joints were investigated.Besides,the joint's interface microstructure,composition,and phases were analyzed.Results show that the AgCuInTi filler metal exerts a good wetting effect to the surface of cemented carbide and steel.With the increase in brazing temperature,the wetting angle decreases and the spreading area increases.The suitable temperature for vacuum brazing of PDC cutters is 770℃,and the maximum shear strength is 228 MPa at this temperature.
基金the National Natural Science Foundation of China(No.U1934213)the Sichuan Science and Technology Program(No.2019YFG0460)。
文摘The cutter layout of a full-face tunnel boring machine(TBM)directly affects its tunneling efficiency.The revolving diameter of the center cutter is small,and the double-edged design results in its rock breaking mechanism and force characteristics being significantly different from those of the single-edged cutter.The gage cutter is installed on the transition arc of the cutterhead,and the installation inclination complicates its movement and force.In this paper,by taking sandstone as the research object,the composite rock breaking models of the center cutter group and the gage cutter group of a compound TBM are separately established based on the three-dimensional particle discrete element method.The numerical models are verified by comparing results with the full-scale rotary cutting laboratory test.From the view point of the force characteristics of a single cutter,the propagation of rock cracks between adjacent cutters,the overall mechanical properties of the cutterhead,the load characteristics and layout form of the double-edged center cutter,and the installation angle range of the gage cutter were studied.Results demonstrate that the use of a cross-shaped center cutter layout can reduce the force of a single cutter ring and the overall load of the cutterhead,which is conducive to TBM stability during tunneling.Therefore,it is recommended that a cross-shaped layout for the double-edged center cutter of a rock formation compound TBM should be used.To improve the stability and service life of the cutter,we recommend setting the installation angle of the innermost gage cutter of the rock formation compound TBM to about 9°,and the installation angle of the outermost gage cutter should not exceed 70°.
基金Beijing Postdoctoral Research Activity Funding Project,Grant/Award Number:2022-ZZ-097Beijing Municipal Natural Science Foundation,Grant/Award Number:8182048。
文摘During shield tunneling in highly abrasive formations such as sand–pebble strata,nonuniform wear of shield cutters is inevitable due to the different cutting distances.Frequent downtimes and cutter replacements have become major obstacles to long-distance shield driving in sand–pebble strata.Based on the cutter wear characteristics in sand–pebble strata in Beijing,a design methodology for the cutterhead and cutters was established in this study to achieve uniform wear of all cutters by the principle of frictional wear.The applicability of the design method was verified through three-dimensional simulations using the engineering discrete element method.The results show that uniform wear of all cutters on the cutterhead could be achieved by installing different numbers of cutters on each trajectory radius and designing a curved spoke with a certain arch height according to the shield diameter.Under the uniform wear scheme,the cutter wear coefficient is greatly reduced,and the largest shield driving distance is increased by approximately 47%over the engineering scheme.The research results indicate that the problem of nonuniform cutter wear in shield excavation could be overcome,thereby providing guiding significance for theoretical innovation and construction of long-distance shield excavation in highly abrasive strata.
基金Projects(51275339,51575379,51675374)supported by the National Natural Science Foundation of ChinaProject(2013CB035402)supported by the National Hi-tech Research and Development Program of China
文摘Studies to date have failed to consider gage disc cutters’variable cutting depth and the constraints of cutter-head welds,and have ignored the coupling mechanism between the profile of the full-face rock tunnel-boring machine(TBM)cutter-head and the assembled radius layout of the disc cutters.To solve these problems,an adaptive design method for studying cutter layout was proposed.Taking the bearing stress of the outermost gage disc cutter as an index,the profile of the cutter-head was determined.Using a genetic algorithm and based on the principles of equal life and equal wear,the assembled radii of the cutters were optimally designed.Boundary conditions of non-interference between the cutters,manholes,muck buckets and welding lines were given when a star layout pattern was used on cutters.The cutter-head comprehensive evaluation model was established by adopting relative optimization improvement degree of evaluation indices to achieve dimensional consistency.Exemplifying the MB264-311-8030 mm tape TBM cutter-head,the calculations show that compared with the original layout scheme,among the 51 disc cutters,the largest gap of the cutters’assembled radiuses is only 25.8 mm,which is 0.64%of the cutter-head’s radius and is negligible.The cutter-head’s unbalanced radial force decreases by 62.41%,the overturning moment decreases by 33.22%,and the cutter group’s centroid shift increases by only 18.48%.Each index is better than or approximately equal to the original cutter-head layout scheme,and the equivalent stress and deformation are both smaller;these results fully verify the feasibility and effectiveness of the method.
文摘In order to develop a rotary percussive bit with diamond enhanced cutters assisted by high pressure water jets, it is necessary to study the damage mechanism and the penetration properties of PDC cutters subject to different impact load level and rock types. Therefore the impact experiments of the single PDC cutters with different attack angles in four rocks: black basalt, Missouri red granite, Halston limestone, and a very soft (Roubidoux) sandstone were carried out, and the effects of rake angles of PDC cutters on both the penetration and impact resistance of PDC cutters have been discussed in detail. Test results show that a PDC insert can withstand a very strong impact in compression but is easily damaged by impact shearing, the PDC cutters are more easily damaged by shearing if the attack angles are relatively small, the 45? PDC cutters have the least penetration resistance among the cutters tested. Thus it is suggested that the attack angles of PDC cutters should be larger than 30? for bits which must withstand impact from a hammer.
基金financially supported by Disciplines Group Project of Jianghan University's Thirteenth Five-year Plan for Vehicle Material Development and Testing (No.03430001)the Wuhan Science and Technology Bureau (No.2013071004010468)the Scientific and Technological Research Project of Hubei Provincial Department of Education (No.B2014076)
文摘Copper and zinc were recovered from waste diamond cutters through leaching with an ammonia–ammonium sulfate system and air as an oxidant. The effects of experimental parameters on the leaching process were investigated, and the potential–pH(E–pH) diagrams of Cu–NH_3–SO_4^(2-)–H_2O and Zn–NH_3–SO_4^(-2)–H_2O at 25°C were drawn. Results showed that the optimal parameters for the leaching reaction are as follows: reaction temperature, 45°C; leaching duration, 3 h; liquid-to-solid ratio, 50:1(mL/g); stirring speed, 200 r/min; ammonia concentration, 4.0 mol/L; ammonium sulfate concentration, 1.0 mol/L; and air flow rate, 0.2 L/min. The results of the kinetics study indicated that the leaching is controlled by the surface chemical reaction at temperatures below 35°C, and the leaching is controlled by diffusion through the product layer at temperatures above 35°C.
基金supported by the National Science and Technology Major Project(No.2016ZX04002-005)
文摘The concept of cutting platform is proposed and realized based on the latest two step automated tape laying (Two step ATL)technology,which separates prepreg cutting process from tape laying to improve productivity for large parts with small features.Two step ATL is more efficient than conventional layup because ply patches are pre cut in a separate operation.The concept of the prepreg tape cutting experimental platform with two cutters is introduced.Further,based on the automatic tape laying trajectory planning software,a two cutter cutting algorithm is proposed.Cutting experiments are reported to validate both the concept of cutting platform and cutting algorithm.
基金Supported by National Natural Science Foundation of China(Grant No.51475163)National Hi-tech Research and Development Program of China(863 Program,Grant No.2012AA041803)
文摘Attempts to minimize energy consumption of a tunnel boring machine disc cutter during the process of fragmentation have largely focused on optimizing disc- cutter spacing, as determined by the minimum specific energy required for fragmentation; however, indentation tests showed that rock deforms plastically beneath the cutters. Equations for thrust were developed for both the traditional, popularly employed disc cutter and anew design based on three-dimensional theory. The respective energy consumption for penetration, rolling, and side-slip fragmentations were obtained. A change in disc-cutter fragmentation angles resulted in a change in the nature of the interaction between the cutter and rock, which lowered the specific energy of fragmentation. During actual field excavations to the same penetration length, the combined energy consumption for fragmentation using the newly designed cutters was 15% lower than that when using the traditional design. This paper presents a theory for energy saving in tunnel boring machines. Investigation results showed that the disc cutters designed using this theory were more durable than traditional designs, and effectively lowered the energy consumption.
基金Supported by National Natural Science Foundation of China (Grant No.51075147)National Hi-tech Research and Development Program of China (863 Program,Grant No.2012AA041803)
文摘Wear is a major factor of disc cutters’ failure. No current theory offers a standard for the prediction of disc cutter wear yet. In the field the wear prediction method commonly used is based on the excavation length of tunnel boring machine（TBM） to predict the disc cutter wear and its wear law, considering the location number of each disc cutter on the cutterhead（radius for installation）; in theory, there is a prediction method of using arc wear coefficient. However, the preceding two methods have their own errors, with their accuracy being 40% or so and largely relying on the technicians’ experience. Therefore, radial wear coefficient, axial wear coefficient and trajectory wear coefficient are defined on the basis of the operating characteristics of TBM. With reference to the installation and characteristics of disc cutters, those coefficients are modified according to penetration, which gives rise to the presentation of comprehensive axial wear coefficient, comprehensive radial wear coefficient and comprehensive trajectory wear coefficient. Calculation and determination of wear coefficients are made with consideration of data from a segment of TBM project（excavation length 173 m）. The resulting wear coefficient values, after modification, are adopted to predict the disc cutter wear in the follow-up segment of the TBM project（excavation length of 5621 m）. The prediction results show that the disc cutter wear predicted with comprehensive radial wear coefficient and comprehensive trajectory wear coefficient are not only accurate（accuracy 16.12%） but also highly congruous, whereas there is a larger deviation in the prediction with comprehensive axial wear coefficient（accuracy 41%, which is in agreement with the prediction of disc cutters’ life in the field）. This paper puts forth a new method concerning prediction of life span and wear of TBM disc cutters as well as timing for replacing disc cutters.
基金supported by the National Natural Science Foundation of China(Grant No.51475163)the National Hightech R&D Program of China(Grant No.2012AA041803)
文摘Predicting the cutter consumption and the exact time to replace the worn-out cutters in tunneling projects constructed with tunnel boring machine(TBM) is always a challenging issue. In this paper, we focus on the analyses of cutter motion in the rock breaking process and trajectory of rock breaking point on the cutter edge in rocks. The analytical expressions of the length of face along which the breaking point moves and the length of spiral trajectory of the maximum penetration point are derived. Through observation of rock breaking process of disc cutters as well as analysis of disc rock interaction, the following concepts are proposed: the arc length theory of predicting wear extent of inner and center cutters, and the spiral theory of predicting wear extent of gage and transition cutters. Data obtained from5621 m-long Qinling tunnel reveal that among 39 disc cutters, the relative errors between cumulatively predicted and measured wear values for nine cutters are larger than 20%, while approximately 76.9% of total cutters have the relative errors less than 20%. The proposed method could offer a new attempt to predict the disc cutter's wear extent and changing time.
基金supported by Hunan Provincial Natural Science Foundation of China (Grant Nos. 10JJ2040, 11JJ3055)National Major Science and Technology Special Projects of China (Grant No.2012ZX04011-011)+1 种基金Postdoctoral Science Funded Project of China (GrantNo. 20110490261)Hunan Provincial 12th Five-year Plan Key Disciplines of China (Grant No. 2012-42)
文摘Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact cutting force model that can accurately reflect a true cutting process. However, there is little research on the prediction of chatter stablity in milling. Based on the generalized mathematical model of inserted cutters introduced by ENGIN, an improved geometrical, mechanical and dynamic model for the vast variety of inserted cutters widely used in engineering applications is presented, in which the average directional cutting force coefficients are obtained by means of a numerical approach, thus leading to an analytical determination of stability lobes diagram (SLD) on the axial depth of cut. A new kind of SLD on the radial depth of cut is also created to satisfy the special requirement of inserted cutter milling. The corresponding algorithms used for predicting cutting forces, vibrations, dimensional surface finish and stability lobes in inserted cutter milling under different cutting conditions are put forward. Thereafter, a dynamic simulation module of inserted cutter milling is implemented by using hybrid program of Matlab with Visual Basic. Verification tests are conducted on a vertical machine center for Aluminum alloy LC4 by using two different types of inserted cutters, and the effectiveness of the model and the algorithm is verified by the good agreement of simulation result with that of cutting tests under different cutting conditions. The proposed model can predict the cutting process accurately under a variety of cutting conditions, and a high efficient and chatter-free milling operation can be achieved by a cutting condition optimization in industry applications.
基金Supported by National Natural Science Foundation of China(Grant No.51975168).
文摘Titanium alloy has been applied in the field of aerospace manufacturing for its high specific strength and hardness.Nonetheless,these properties also cause general problems in the machining,such as processing inefficiency,serious wear,poor workpiece face quality,etc.Aiming at the above problems,this paper carried out a comparative experimental study on titanium alloy milling based on the CAMCand BEMC.The variation law of cutting force and wear morphology of the two tools were obtained,and the wear mechanism and the effect of wear on machining quality were analyzed.The conclusion is that in contrast with BEMC,under the action of cutting thickness thinning mechanism,the force of CAMC was less,and its fluctuation was more stable.The flank wear was uniform and near the cutting edge,and the wear rate was slower.In the early period,the wear mechanism of CAMC was mainly adhesion.Gradually,oxidative wear also occurred with milling.Furthermore,the surface residual height of CAMC was lower.There is no obvious peak and trough accompanied by fewer surface defects.
基金funded by the National Key Research and Development Program of China (No. 2021YFB3401501)the Fundamental Research Funds for the Central Universities (No2022JCCXLJ01)。
文摘A plane mechanical model of rock breaking process by double disc cutter at the center of the cutterhead is established based on contact mechanics to analyze the stress evolution in the rock broken by cutters with different spacings. A continuous-discontinuous coupling numerical method based on zero-thickness cohesive elements is developed to simulate rock breaking using double cutters. The process, mechanism,and characteristics of rock breaking are comprehensively analyzed from five aspects: peak force, breaking form, breaking efficiency, crack mode, and breaking degree. The results show that under the penetrating action of cutters, dense cores are formed due to shear failure under respective cutters. The tensile cracks propagate in the rock, and then rock chips form with increasing penetration depth. When the cutter spacing is increased from 10 to 80 mm, the peak force gradually increases, the rock breaking range increases first and then decreases, the specific energy decreases first and then rises, and the breaking coefficient of intermediate rock decreases from 0.955 to 0.788. The area of rock breaking is positively correlated with the length of the tensile crack. Furthermore, the length of the tensile crack accounts for 14.4%–33.6% of the total crack length.
文摘How to generate rake faces of nonconventional milling cutters (NCMC) with constant spiral angled and normal rake angled edges on NC machine tools is presented by use of a blunt cup grinder or a cup milling cutter. Motion functions of the NC machining system are mathematically deduced and exam- ed by a experiment. The research will provide theoretical and practical guidance for machining noncon- ventional tools on NC machine tools.
基金supported by the National Natural Science Foundation of China(No.51475328)the National Science and Technology Major Project of China(No.2015ZX04001202)
文摘Power generators and chemical engineering compressors include heavy and large centrifugal impellers. To produce these impellers in high-speed machining, a 4?-axis milling machine(or a 4-axis machine plus an indexing table) is often used in the industry, which is more rigid than a5-axis milling machine. Since impeller blades are designed with complex B-spline surfaces and impeller channels spaces vary significantly, it is more efficient to use multiple cutters as large as possible to cut a channel in sections and a blade surface in patches, instead of only using a small cutter to machine a whole blade and a channel. Unfortunately, no approach has been established to automatically calculate the largest diameters of cutters and their paths, which include the indexing table angles. To address this problem, an automated and optimization approach is proposed. Based on the structure of a 4?-axis machine, a geometric model for a cutter gouging/interfering the impeller is formulated, and an optimization model of the cutter diameter in terms of the indexing table angle is established at a cutter contact(CC) point on a blade surface. Then, the diameters of the tools,their orientations, and the indexing table angles are optimized, and each tool's paths are generated for machining its corresponding impeller section. As a test, an impeller is efficiently machined with these tools section by section; thus, this approach is valid. It can be directly used in the industry to improve efficiency of machining centrifugal impellers.
基金Project(2012AA041801)supported by the Hi-tech Research and Development Program of ChinaProject(2013CB035401)supported by the National Basic Research Program of ChinaProject(51475478)supported by the National Natural Science Foundation of China
文摘The disc cutters of tunnel boring machine(TBM) are installed with different polar angles. This causes the cutting depth difference between adjacent disc cutters on the tunnel face. A rock-cutting model was established to study the rock fragmentation law between adjacent disc cutters with different polar angles based on particle flow code(PFC). The influence of polar angle of adjacent disc cutters on rock cracks and stresses under different cutter spacing and penetration was studied. Research shows that polar angle difference leads to the discontinuity of rock-fragmentation process by adjacent cutters. The effect of rock-fragmentation is influenced by the cutting depth difference between adjacent cutters. The effect of rock-fragmentation performed best, meanwhile large rock blocks were flaked when the difference of cutting depth is half of the penetration. Too large or small difference of the cutting depth will cause high specific energy consumption of rock fragmentation. The specific energy consumption is relatively small when the difference of cutting depth is half of the penetration.
基金Project(2013CB035401) supported by the National Basic Research Program of ChinaProject(51174228) supported by the National Natural Science Foundation of China+1 种基金Project(71380100003) supported by Hunan Provincial Innovation Foundation for Postgraduate,ChinaProject(201304) supported by Open Research Fund of Hunan Province Key Laboratory of Safe Mining Techniques of Coal Mines(Hunan University of Science and Technology),China
文摘Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the effects of discontinuities on cutting characteristics and cutting efficiency. In laboratory tests, five propagation patterns of radial cracks are observed. And in the numerical tests, firstly, it is similar to laboratory tests that cracks ahead of cutters mainly initiate from the crushed zone, and some minor cracks will initiate from joints. The cracks initiating from crushed zones will run through the thinner joints while they will be held back by thick joints. Cracks tend to propagate towards the tips of embedded cracks, and minor cracks will initiate from the tips of embedded cracks, which may result in the decrease of specific area, and disturbing layers play as ‘screens', which will prevent cracks from developing greatly. The peak penetration forces, the consumed energy in the penetration process and the uniaxial compression strength will decrease with the increase of discontinuities. The existence of discontinuities will result in the decrease of the cutting efficiency when the spacing between cutters is 70 mm. Some modifications should be made to improve the efficiency when the rocks containing groups of discontinuities are encountered.
基金Project(2013CB035401)supported by the National Basic Research Program of ChinaProject(51174228)supported by the National Natural Science Foundation of China+1 种基金Project(201304)supported by Open Research Fund of Hunan Province Key Laboratory of Safe Mining Techniques of Coal Mines(Hunan University of Science and Technology),ChinaProject(14C0746)supported by the Education Department of Hunan Province,China
文摘Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000) designed and manufactured in Central South University(China). Results are obtained by performing analysis on the fracture scopes of cement and granite plates,the characteristics of cutting force in cutting processes and the cutting efficiency. Firstly, the increase of latitude fracture scope and the decrease of longitude fracture scope are both more notable in the tests conducted on cement plates subjected to the increasing confining stresses; secondly, the increase tendency of peak penetration forces obtained from tests conducted on granite plates is more obvious, however, the increase tendencies of average penetration forces achieved from cement and granite plates are close to each other; thirdly, the cutting efficiency could be improved by increasing the spacing between cutters when the confining stress which acts on soft and hard rock increases in a certain degree, and the cutting efficiency of soft rock is more sensitive to the varying confining stresses.
文摘The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts and the maximum tangential stress criterion are used to investigate the micro crack propagation and its direction underneath the excavating discs. A higher order displacement discontinuity method with quadratic displacement discontinuity elements is used to estimate the stress intensity factors near the crack tips. Rock cutting mechanisms under single and double type discs are simulated by the proposed numerical method.The main purposes of the present modeling are to simulate the chip formation process of indented rocks by single and double discs.The effects of specific disc parameters(except speed) on the thrust force Ft, the rolling force Fr, and the specific energy ES are investigated. It has been shown that the specific energy(energy required to cut through a unit volume of rock) of the double disc is less than that of the single disc. Crack propagation in rocks under disc cutters is numerically modeled and the optimum ratio of disc spacing S to penetration depth Pd(i.e. S/Pd ratio) of about 10 is obtained, which is in good agreement with the theoretical and experimental results cited in the literature.
