The main geometrical and operating parameters of the water steam centrifugal compressors working in various concentrator operating conditions are realized in this paper. The interdependence between centrifugal stage p...The main geometrical and operating parameters of the water steam centrifugal compressors working in various concentrator operating conditions are realized in this paper. The interdependence between centrifugal stage pressure ratio, peripheral Mach number and impeller peripheral speed, as well the influence of the concentrator system capacity on the dimensions of the centrifugal compressor are determined to obtain the range of reasonable usage of the centrifugal thermocompression systems in the industrial concentrators. The high peripheral impeller speed, high Mach number and high pressure ratio cause separated jet-wake flow and transonic flow phenomena in the water steam centrifugal compressor flow field. The calculating methods for 3-D viscid unsteady transonic fluid flows in the turbocompressors are discussed and the results of CFD simulations and experimental investigations are used for optimal design of the water steam centrifugal compressor flow field. The application of the centrifugal compressor in the industrial concentrators with thermocompression systems and the influence on the energy efficiency of the systems are analyzed. Significant increment of the energy efficiency of the industrial concentrators can be achieved by introduction of the thermocompression systems.展开更多
Concentrating solar power （CSP） technologies could be one of the major contributor to worlds future energy needs and which would be cheap and clean sources of energy. This would improve energy utilization, higher co...Concentrating solar power （CSP） technologies could be one of the major contributor to worlds future energy needs and which would be cheap and clean sources of energy. This would improve energy utilization, higher conversion efficiency with reliable and affordable supply of electricity to the public. The proposed approach is using 18 inch diameter of solar dish concentrator to measure the solar radiation using the aluminium foil as a reflector. In this paper, solar radiation is collected to investigate the solar fraction on incoming solar energy in wet climate.展开更多
The phasor data concentrator placement(PDCP)in wide area measurement systems(WAMS)is an optimization problem in the communication network planning for power grid.Instead of using the traditional integer linear program...The phasor data concentrator placement(PDCP)in wide area measurement systems(WAMS)is an optimization problem in the communication network planning for power grid.Instead of using the traditional integer linear programming(ILP)based modeling and solution schemes that ignore the graph-related features of WAMS,in this work,the PDCP problem is solved through a heuristic graphbased two-phase procedure(TPP):topology partitioning,and phasor data concentrator(PDC)provisioning.Based on the existing minimum k-section algorithms in graph theory,the k-base topology partitioning algorithm is proposed.To improve the performance,the“center-node-last”pre-partitioning algorithm is proposed to give an initial partition before the k-base partitioning algorithm is applied.Then,the PDC provisioning algorithm is proposed to locate PDCs into the decomposed sub-graphs.The proposed TPP was evaluated on five different IEEE benchmark test power systems and the achieved overall communication performance compared to the ILP based schemes show the validity and efficiency of the proposed method.展开更多
The Rukwa Rift section of the East Africa Rift System presents a type setting for radiogenic helium accumulation in a petroleum free basin.As a prerequisite for accumulation,a considerable high heat flow anomaly is re...The Rukwa Rift section of the East Africa Rift System presents a type setting for radiogenic helium accumulation in a petroleum free basin.As a prerequisite for accumulation,a considerable high heat flow anomaly is required from tectonothermal events to drive the release and circulation of radiogenic helium in the continental crust.Here we apply statistical analysis on geochemical data observed in thermal springs and recorded heat flow to account for crustal helium mass balance for each tectonothermal event in the region.Our results demonstrate anomalously high heat flow~64-99 mW/m^(2) with a consistent trend of helium isotopic ratio and fluid chemistry in the Rukwa Rift.Mass balance calculation show that the whole crustal volume underlying the East Africa Helium Pool(EAHP)has a capability of producing radiogenic helium of about 9.9×10^(6) mol/yr(22×10^(-6) mol 4He/m^(2) yr)while the total radiogenic helium flux ranges between~2.39×10^(6) mol/yr and~2.68×10^(9) mol/yr.The Tanzania Craton contributes largely to radiogenic helium releasing up to 50% of the total capacity in the region.The total ^(4)He emission in the Rukwa Rift Basin is about 4.45×10^(5)-5.01×10^(8) mol/yr which is thus equivalent to 19%-21% of the total production capacity in the region.These results imply that the helium accumulation in the EAHP would have started as early as Paleoproterozoic(2.349 Ga).These results provide a qualitative and quantitative insight to assess both helium and geothermal potentiality in the region.展开更多
Purpose-This paper provides a comprehensive analysis of the Brazilian freight railway system,examining the efficacy of the current concession renewal model in light of persistent structural problems such as market con...Purpose-This paper provides a comprehensive analysis of the Brazilian freight railway system,examining the efficacy of the current concession renewal model in light of persistent structural problems such as market concentration,cargo dependence on export commodities and underutilization of the network.Situating Brazil within the broader international debate on railway reforms,the paper evaluates whether the ongoing early renewal of concessions can deliver a more diversified and competitive freight system.Design/methodology/approach-The study adopts a sequential mixed-methods research design that integrates longitudinal quantitative analysis with qualitative institutional and policy evaluation.The quantitative component examines time-series indicators published by ANTT,DNIT and INFRA S.A.from 1999 to 2023 to identify structural patterns in traffic growth,investment,safety and market concentration.The qualitative component employs a process-tracing logic to reconstruct the evolution of concession renewals and the implementation of Railway Law 14.273/2021,drawing on concepts from regulatory economics,institutional theory and industrial organization.These empirical streams are synthesized through an analytical framework that connects three dimensions-regulatory design,market structure and system performance-allowing for a systematic assessment of how Brazil’s institutional configuration shapes incentives,competitive dynamics and network utilization.Findings-The analysis confirms that the early renewal of concessions has successfully secured substantial private investment for capacity expansion on existing trunk lines.However,it has perpetuated the vertically integrated model,reinforcing the market power of incumbent operators and failing to significantly promote intramodal competition or cargo diversification.The system remains dominated by iron ore and agricultural commodities,with general cargo representing a minuscule share.The new authorization regime and short-line railway policies present a viable pathway for market opening but face significant operational and institutional barriers to implementation.Originality/value-This research offers a timely and critical assessment of a pivotal moment in Brazilian railway policy.It moves beyond a simplistic evaluation of volume growth to a structural analysis of market failures and the interplay between concession renewal and regulatory innovation.The findings provide actionable insights for policymakers in Brazil and other emerging economies seeking to balance private investment with public interest goals in railway infrastructure,highlighting the necessity of complementary,pro-competitive measures alongside financial investment.展开更多
The nonuniform irradiation in the standard photovoltaic（PV） cells causes their relatively high series resistance,which results in a considerably lowered efficiency of PV cells.Currently the concentrator of uniform i...The nonuniform irradiation in the standard photovoltaic（PV） cells causes their relatively high series resistance,which results in a considerably lowered efficiency of PV cells.Currently the concentrator of uniform irradiation designed for concentrator photovoltaic is rare in China and lack sufficient theoretical research.In this paper,a systematic research on the solar reflective concentrator is conducted.A novel structure for a solar reflective concentrator is designed with the application of a flat mirror matrix to concentrate the sunlight for concentrator photovoltaic（CPV） systems.Sunlight beams are focused through the reflection of the mirror array on the solar cell to generate electricity.The concentrator is capable of producing much more uniform sunlight with a certain concentration ratio.The design scheme includes laying out the flat mirrors,optimizing the optical pathway and the parameters of each mirror.The prototype of the CPV system was installed at Nanjing,China.In the configuration of the prototype,it is composed of 24 pieces parallelogram flat mirrors,which are arranged into a total reflective array of 5 rows and 5 columns.In comparison with the parabolic trough concentrator,the experimental measurements verify such design has high efficiency.The concentrator model of a flat mirror matrix and the proposed new design method will lay a solid foundation for designing the concentrator of uniform irradiation.展开更多
Positron sources are one of the most important components of the injector of a circular electron positron collector(CEPC).The CEPC is designed as an e^(+)e^(−)collider for a Higgs factory.Its accelerator system is com...Positron sources are one of the most important components of the injector of a circular electron positron collector(CEPC).The CEPC is designed as an e^(+)e^(−)collider for a Higgs factory.Its accelerator system is composed of 100-km-long storage rings and an injector.The design goal of the positron source is to obtain positron beams with a bunch charge of 3 nC.The flux concentrator(FC)is one of the cores of the positron source.This paper reports the design,development,and measurements of an FC prototype system.The prototype includes an FC and an all-solid-state high-current pulse modulator.Preliminary tests show that the peak current on the FC can reach 15.5 kA,and the peak magnetic field can reach 6.2 T.The test results are consistent with the theoretical simulation.The FC system fulfills the requirements of the CEPC positron source as well as provides a reference for the development of similar devices both domestically and abroad.展开更多
This paper describes various aspects of the design methodology and heat transfer calculations for an elevated linear absorber. The absorber is a part of the linear Fresnel reflector solar concentrator system, in which...This paper describes various aspects of the design methodology and heat transfer calculations for an elevated linear absorber. The absorber is a part of the linear Fresnel reflector solar concentrator system, in which hot fluid is generated. The design of the absorber is an inverted trapezoidal air cavity with a glass cover enclosing a multi tube absorber. In a trapezoidal cavity absorber, a set of linear multi tube absorber with plate(named as "plane surface") and without plate(named as "tube surface") underneath are considered. An analytical simulation is done for different gaps between the tubes and for different depths of the cavity. A better design of the absorber is found out to maximize the heat transfer rate supplied to the absorber tube fluid. Also, the experimentally obtained overall heat loss coefficients are compared with the analytical values for the considered arrangements of absorber set up and results are discussed in details.展开更多
A metal plate cooling model for 400~ single concentrator solar cells was established. The effects of the thickness and the radius of the metal plate, and the air environment on the temperature of the solar cells were ...A metal plate cooling model for 400~ single concentrator solar cells was established. The effects of the thickness and the radius of the metal plate, and the air environment on the temperature of the solar cells were analyzed in detail. It is shown that the temperature of the solar cells decreased sharply at the beginning, with the increase in the thickness of the metal plate, and then changed more smoothly. When the radius of the metal plate was 4 cm and the thickness increased to 2 mm or thicker, the temperature of the solar cell basically stabilized at about 53℃. Increasing the radius of the metal plate and the convective transfer coefficient made the temperature of the solar cell decrease remarkably. The effects of A1 and Cu as the metal plate material on cooling were analyzed contrastively, and demonstrated the superiority of A1 material for the cooling system. Furthermore, considering cost reduction, space holding and the stress of the system, we optimized the structural design of the metal plate. The simulated results can be referred to the design of the structure for the metal plate. Finally, a method to devise the structure of the metal plate for single concentrator solar cells was given.展开更多
A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance ...A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.展开更多
In the background of the low-carbon transformation of the energy structure,the problem of operational uncertainty caused by the high proportion of renewable energy sources and diverse loads in the integrated energy sy...In the background of the low-carbon transformation of the energy structure,the problem of operational uncertainty caused by the high proportion of renewable energy sources and diverse loads in the integrated energy systems(IES)is becoming increasingly obvious.In this case,to promote the low-carbon operation of IES and renewable energy consumption,and to improve the IES anti-interference ability,this paper proposes an IES scheduling strategy that considers CCS-P2G and concentrating solar power(CSP)station.Firstly,CSP station,gas hydrogen doping mode and variable hydrogen doping ratio mode are applied to IES,and combined with CCS-P2G coupling model,the IES low-carbon economic dispatch model is established.Secondly,the stepped carbon trading mechanism is applied,and the sensitivity analysis of IES carbon trading is carried out.Finally,an IES optimal scheduling strategy based on fuzzy opportunity constraints and an IES risk assessment strategy based on CVaR theory are established.The simulation shows that the gas-hydrogen doping model proposed in this paper reduces the operating cost and carbon emission of IES by 1.32%and 7.17%,and improves the carbon benefit by 5.73%;variable hydrogen doping ratio model reduces the operating cost and carbon emission of IES by 3.75%and 1.70%,respectively;CSP stations reduce 19.64%and 38.52%of the operating costs of IES and 1.03%and 1.80%of the carbon emissions of IES respectively compared to equal-capacity photovoltaic and wind turbines;the baseline price of carbon trading of IES and its rate of change jointly affect the carbon emissions of IES;evaluating the anti-interference capability of IES through trapezoidal fuzzy number and weighting coefficients,enabling IES to guarantee operation at the lowest cost.展开更多
Several conjugate components represent the aquatic ecosystem of Lake Baikal:Baikal water(surface and deep water),groundwater from boreholes,water of numerous Baikal tributaries,cold and hot mineral springs around Lake...Several conjugate components represent the aquatic ecosystem of Lake Baikal:Baikal water(surface and deep water),groundwater from boreholes,water of numerous Baikal tributaries,cold and hot mineral springs around Lake Baikal,and the Angara River,the only runoff reflecting all this aquatic diversity.River waters in the Baikal region are known to be deficient in some vital elements,including fluorine.This article discusses the features of the fluorine distribution in the water from the conjugate components of the Baikal ecosystem.Fluorine ion concentrations in the water of the Baikal ecosystem was determined using the potentiometric method.The study represents the monitoring that was carried out between 1997 and 2022 years.We determine likely causes of high and low fluorine concentrations in the water from different components,propose and substantiate the fluorine sources,geological and geochemical model of its influx and distribution features in the water of the Baikal ecosystem.展开更多
This work aims at the mathematical modeling of a parabolic trough concentrator, the numerical resolution of the resulting equation, as well as the simulation of the heat transfer fluid heating process. To do this, a t...This work aims at the mathematical modeling of a parabolic trough concentrator, the numerical resolution of the resulting equation, as well as the simulation of the heat transfer fluid heating process. To do this, a thermal balance was established for the heat transfer fluid, the absorber and the glass. This allowed us to establish an equation system whose resolution was done by the finite difference method. Then, a computer program was developed to simulate the temperatures of the heat transfer fluid, the absorber tube and the glass as a function of time and space. The numerical resolution made it possible to obtain the temperatures of the heat transfer fluid, the absorber and the glass. The simulation of the fluid heating process was done in one-hour time steps, from six in the morning to six in the afternoon. The results obtained show that the temperature difference between the inlet and the outlet of the sensor is very significant. These results obtained, regarding the variation of the temperatures of the heat transfer fluid, the absorber and the glass, as well as the powers and efficiency of the parabolic trough concentrator and various factors, allow for the improvement of the performances of our prototype.展开更多
Conventional concentrator photovoltaics(CPV)face a persistent trade-off between high efficiency and high cost,driven by expensive multi-junction solar cells and complex active cooling systems.This study presents a com...Conventional concentrator photovoltaics(CPV)face a persistent trade-off between high efficiency and high cost,driven by expensive multi-junction solar cells and complex active cooling systems.This study presents a computational investigation of a novel Multi-Focal Pyramidal Array(MFPA)-based CPV system designed to overcome this limitation.The MFPA architecture employs a geometrically optimized pyramidal concentrator to distribute concen-trated sunlight onto strategically placed,low-cost monocrystalline silicon cells,enabling high efficiency energy capture while passively managing thermal loads.Coupled optical thermal electrical simulations in COMSOL Multiphysics demonstrate a geometric concentration ratio of 120×,with system temperatures maintained below 110℃ under standard 1000 W/m2 Direct Normal Irradiance(DNI).Ray tracing confirms 95%optical efficiency and a concentrated light spot radius of 2.48 mm.Compared with conventional CPV designs,the MFPA improves power-per-cost by 25%and reduces tracking requirements by 50%owing to its wide±15°acceptance angle.These results highlight the MFPA’s potential as a scalable,low-cost,and energy-efficient pathway for expanding solar power generation.展开更多
Solar concentrators laterally converge solar energy to the side of architectural glass and are attractive candidates for building-integrated photovoltaics.Present available luminescent-type and scattering-type solar c...Solar concentrators laterally converge solar energy to the side of architectural glass and are attractive candidates for building-integrated photovoltaics.Present available luminescent-type and scattering-type solar concentrators suffer from omnidirectional waveguide induced low efficiency,coloring/hazing restrained aesthetic quality,and poor compatibility with existing architectural glass.Here,we propose a diffractive solar concentrator via directly coating cholesteric liquid crystal(CLC)layers onto the architectural glass.The stacked CLC layers with submicron lateral periodic alignment enable broadband and unidirectional waveguiding inside the glass,and thus supply a high-efficient platform for transmissive solar energy capturing with merits of high aesthetic quality and economic viability.A 1-inch-diameter prototype powers a 10-mW fan outdoors,and a typical 2-m-wide window is calculated to concentrate solar energy by 50 times.The design is expected to bring a global terawatt-scale green energy supply and billion-ton annual carbon emission reduction,meeting with the sustainable development of human society.展开更多
The inhibitory effects of zinc oxide nanoparticles(ZnO NPs)and impacts of N-acylhomoserine lactone(AHL)-based quorum sensing(QS)on biological nitrogen removal(BNR)performance have beenwell-investigated.However,the eff...The inhibitory effects of zinc oxide nanoparticles(ZnO NPs)and impacts of N-acylhomoserine lactone(AHL)-based quorum sensing(QS)on biological nitrogen removal(BNR)performance have beenwell-investigated.However,the effects of ammonia nitrogen(NH_(4)^(+)-N)concentrations on NP toxicity and AHL regulation have seldom been addressed yet.This study consulted on the impacts of ZnO NPs on BNR systems when high NH_(4)^(+)-N concentrationwas available.The synergistic toxic effects of high-strength NH_(4)^(+)-N(200 mg/L)and ZnO NPs resulted in decreased ammonia oxidation rates and dropped the nitrogen removal efficiencies by 17.5%±0.2%.The increased extracellular polymeric substances(EPS)production was observed in response to the high NH_(4)^(+)-N and ZnO NP stress,which indicated the defensemechanism against the toxic effects in the BNR systemswas stimulated.Furthermore,the regulatory effects of exogenous N-decanoyl-homoserine lactone(C_(10)-HSL)-mediated QS system on NP-stressed BNR systems were revealed to improve the BNR performance under different NH_(4)^(+)-N concentrations.The C_(10)-HSL regulated the intracellular reactive oxygen species levels,denitrification functional enzyme activities,and antioxidant enzyme activities,respectively.This probably synergistically enhanced the defense mechanism against NP toxicity.However,compared to the low NH_(4)^(+)-N concentration of 60 mg/L,the efficacy of C_(10)-HSL was inhibited at high NH_(4)^(+)-N levels of 200 mg/L.The findings provided the significant application potential of QS system for BNR when facing toxic compound shock threats.展开更多
In order to better build the neutral beam injector with negative ion source(NNBI),the pre-research on key technologies has been carried out for the comprehensive research facility for fusion technology(CRFFT).Cesium s...In order to better build the neutral beam injector with negative ion source(NNBI),the pre-research on key technologies has been carried out for the comprehensive research facility for fusion technology(CRFFT).Cesium seeding into negative-ion sources is a prerequisite to obtain the required negative hydrogen ion.The performance of ion source largely depends on the cesium conditions in the source.It is very necessary to quantitatively measure the amount of cesium in the source during the plasma on and off periods(vacuum stage).展开更多
Since meteorological conditions are the main factor driving the transport and dispersion of air pollutants,an accurate simulation of the meteorological field will directly affect the accuracy of the atmospheric chemic...Since meteorological conditions are the main factor driving the transport and dispersion of air pollutants,an accurate simulation of the meteorological field will directly affect the accuracy of the atmospheric chemical transport model in simulating PM_(2.5).Based on the NASM joint chemical data assimilation system,the authors quantified the impacts of different meteorological fields on the pollutant simulations as well as revealed the role of meteorological conditions in the accumulation,maintenance,and dissipation of heavy haze pollution.During the two heavy pollution processes from 10 to 24 November 2018,the meteorological fields were obtained using NCEP FNL and ERA5 reanalysis data,each used to drive the WRF model,to analyze the differences in the simulated PM_(2.5) concentration.The results show that the meteorological field has a strong influence on the concentration levels and spatial distribution of the pollution simulations.The ERA5 group had relatively small simulation errors,and more accurate PM_(2.5) simulation results could be obtained.The RMSE was 11.86𝜇g m^(-3)lower than that of the FNL group before assimilation,and 5.77𝜇g m^(-3)lower after joint assimilation.The authors used the PM_(2.5) simulation results obtained by ERA5 data to discuss the role of the wind field and circulation situation on the pollution process,to analyze the correlation between wind speed,temperature,relative humidity,and boundary layer height and pollutant concentrations,and to further clarify the key formation mechanism of this pollution process.展开更多
This study aimed to optimization of the in vitro fertilization system in Cỏ goat oocytes to achieve the maximum possible blastocyst development rate. In Experiment 1, we assessed the effects of IVF media on the in vit...This study aimed to optimization of the in vitro fertilization system in Cỏ goat oocytes to achieve the maximum possible blastocyst development rate. In Experiment 1, we assessed the effects of IVF media on the in vitro fertilization of Cỏ goat oocytes. There was no significant difference in the cleavage, blastocyst, or hatching rates between TALP-Fert and BO-IVF media. Experiment 2 was performed to assess the concentration of sperm in the in vitro fertilization of Cỏ goat oocytes. The matured Cỏ goat oocytes were fertilized in BO-IVF for four sperm concentrations: 5 × 105, 1 × 106, 2 × 106 and 3 × 106 sperm/ml. The blastocyst rate of 2 × 106 sperm/ml and 3 × 106 sperm/ml groups was higher than that of 5 × 105 sperm/ml and 1 × 106 sperm/ml groups (P Experiment 3 was performed to assess the IVF duration on the in vitro fertilization of Cỏ goat oocytes. The matured Cỏ goat oocytes were fertilized in BO-IVF with sperm concentration of 3 × 106 sperm/ml for 18, 20, 22 and 24 h. The cleavage, blastocyst, and hatching blastocyst rates of 18 h group were lower than those of 20, 22 and 24 h groups (P 0.05). In conclusion, the matured Cỏ goat oocytes were fertilized in BO-IVF with sperm concentration of 3 × 106 sperm/ml for 20 hours, which is suitable for the in vitro Cỏ goat embryo production.展开更多
This paper is based on the rainwater collection project in the retrofit of the Dongyi teaching block in Zhejiang University Xixi Campus.The analysis incorporates the local meteorological data, recycling water utilizat...This paper is based on the rainwater collection project in the retrofit of the Dongyi teaching block in Zhejiang University Xixi Campus.The analysis incorporates the local meteorological data, recycling water utilization, and precipitation adjustment.The rainwater collection system in this program also adds the condensation water from the heating, ventilation and air conditioning （ HVAC） system and the concentration from the reverse-osmosis system used for watering greens and supplying waterscapes.By calculating, the quantity of the HVAC condensation water in summer is 3.48 m3/d, and the quantity of the reverse-osmosis concentrated water is 198 to 396 L/d.This method solves the water shortage caused by high evaporation in summer and low precipitation in winter.Supported by empirical monitoring data, the proposed method significantly increases the economic efficiency of the system during the summer period.展开更多
文摘The main geometrical and operating parameters of the water steam centrifugal compressors working in various concentrator operating conditions are realized in this paper. The interdependence between centrifugal stage pressure ratio, peripheral Mach number and impeller peripheral speed, as well the influence of the concentrator system capacity on the dimensions of the centrifugal compressor are determined to obtain the range of reasonable usage of the centrifugal thermocompression systems in the industrial concentrators. The high peripheral impeller speed, high Mach number and high pressure ratio cause separated jet-wake flow and transonic flow phenomena in the water steam centrifugal compressor flow field. The calculating methods for 3-D viscid unsteady transonic fluid flows in the turbocompressors are discussed and the results of CFD simulations and experimental investigations are used for optimal design of the water steam centrifugal compressor flow field. The application of the centrifugal compressor in the industrial concentrators with thermocompression systems and the influence on the energy efficiency of the systems are analyzed. Significant increment of the energy efficiency of the industrial concentrators can be achieved by introduction of the thermocompression systems.
文摘Concentrating solar power （CSP） technologies could be one of the major contributor to worlds future energy needs and which would be cheap and clean sources of energy. This would improve energy utilization, higher conversion efficiency with reliable and affordable supply of electricity to the public. The proposed approach is using 18 inch diameter of solar dish concentrator to measure the solar radiation using the aluminium foil as a reflector. In this paper, solar radiation is collected to investigate the solar fraction on incoming solar energy in wet climate.
基金supported by the National Key Research and Development Program of China(2023YFB 2906403).
文摘The phasor data concentrator placement(PDCP)in wide area measurement systems(WAMS)is an optimization problem in the communication network planning for power grid.Instead of using the traditional integer linear programming(ILP)based modeling and solution schemes that ignore the graph-related features of WAMS,in this work,the PDCP problem is solved through a heuristic graphbased two-phase procedure(TPP):topology partitioning,and phasor data concentrator(PDC)provisioning.Based on the existing minimum k-section algorithms in graph theory,the k-base topology partitioning algorithm is proposed.To improve the performance,the“center-node-last”pre-partitioning algorithm is proposed to give an initial partition before the k-base partitioning algorithm is applied.Then,the PDC provisioning algorithm is proposed to locate PDCs into the decomposed sub-graphs.The proposed TPP was evaluated on five different IEEE benchmark test power systems and the achieved overall communication performance compared to the ILP based schemes show the validity and efficiency of the proposed method.
基金funded by United Kingdom Commonwealth Scholarship Commission。
文摘The Rukwa Rift section of the East Africa Rift System presents a type setting for radiogenic helium accumulation in a petroleum free basin.As a prerequisite for accumulation,a considerable high heat flow anomaly is required from tectonothermal events to drive the release and circulation of radiogenic helium in the continental crust.Here we apply statistical analysis on geochemical data observed in thermal springs and recorded heat flow to account for crustal helium mass balance for each tectonothermal event in the region.Our results demonstrate anomalously high heat flow~64-99 mW/m^(2) with a consistent trend of helium isotopic ratio and fluid chemistry in the Rukwa Rift.Mass balance calculation show that the whole crustal volume underlying the East Africa Helium Pool(EAHP)has a capability of producing radiogenic helium of about 9.9×10^(6) mol/yr(22×10^(-6) mol 4He/m^(2) yr)while the total radiogenic helium flux ranges between~2.39×10^(6) mol/yr and~2.68×10^(9) mol/yr.The Tanzania Craton contributes largely to radiogenic helium releasing up to 50% of the total capacity in the region.The total ^(4)He emission in the Rukwa Rift Basin is about 4.45×10^(5)-5.01×10^(8) mol/yr which is thus equivalent to 19%-21% of the total production capacity in the region.These results imply that the helium accumulation in the EAHP would have started as early as Paleoproterozoic(2.349 Ga).These results provide a qualitative and quantitative insight to assess both helium and geothermal potentiality in the region.
文摘Purpose-This paper provides a comprehensive analysis of the Brazilian freight railway system,examining the efficacy of the current concession renewal model in light of persistent structural problems such as market concentration,cargo dependence on export commodities and underutilization of the network.Situating Brazil within the broader international debate on railway reforms,the paper evaluates whether the ongoing early renewal of concessions can deliver a more diversified and competitive freight system.Design/methodology/approach-The study adopts a sequential mixed-methods research design that integrates longitudinal quantitative analysis with qualitative institutional and policy evaluation.The quantitative component examines time-series indicators published by ANTT,DNIT and INFRA S.A.from 1999 to 2023 to identify structural patterns in traffic growth,investment,safety and market concentration.The qualitative component employs a process-tracing logic to reconstruct the evolution of concession renewals and the implementation of Railway Law 14.273/2021,drawing on concepts from regulatory economics,institutional theory and industrial organization.These empirical streams are synthesized through an analytical framework that connects three dimensions-regulatory design,market structure and system performance-allowing for a systematic assessment of how Brazil’s institutional configuration shapes incentives,competitive dynamics and network utilization.Findings-The analysis confirms that the early renewal of concessions has successfully secured substantial private investment for capacity expansion on existing trunk lines.However,it has perpetuated the vertically integrated model,reinforcing the market power of incumbent operators and failing to significantly promote intramodal competition or cargo diversification.The system remains dominated by iron ore and agricultural commodities,with general cargo representing a minuscule share.The new authorization regime and short-line railway policies present a viable pathway for market opening but face significant operational and institutional barriers to implementation.Originality/value-This research offers a timely and critical assessment of a pivotal moment in Brazilian railway policy.It moves beyond a simplistic evaluation of volume growth to a structural analysis of market failures and the interplay between concession renewal and regulatory innovation.The findings provide actionable insights for policymakers in Brazil and other emerging economies seeking to balance private investment with public interest goals in railway infrastructure,highlighting the necessity of complementary,pro-competitive measures alongside financial investment.
基金supported by National Natural Science Foundation of China (Grant No. 50775035)National Hi-tech Research and Development Program of China (863 Program,Grant No. 2006AA050203,Grant No. 2007AA04Z421)
文摘The nonuniform irradiation in the standard photovoltaic（PV） cells causes their relatively high series resistance,which results in a considerably lowered efficiency of PV cells.Currently the concentrator of uniform irradiation designed for concentrator photovoltaic is rare in China and lack sufficient theoretical research.In this paper,a systematic research on the solar reflective concentrator is conducted.A novel structure for a solar reflective concentrator is designed with the application of a flat mirror matrix to concentrate the sunlight for concentrator photovoltaic（CPV） systems.Sunlight beams are focused through the reflection of the mirror array on the solar cell to generate electricity.The concentrator is capable of producing much more uniform sunlight with a certain concentration ratio.The design scheme includes laying out the flat mirrors,optimizing the optical pathway and the parameters of each mirror.The prototype of the CPV system was installed at Nanjing,China.In the configuration of the prototype,it is composed of 24 pieces parallelogram flat mirrors,which are arranged into a total reflective array of 5 rows and 5 columns.In comparison with the parabolic trough concentrator,the experimental measurements verify such design has high efficiency.The concentrator model of a flat mirror matrix and the proposed new design method will lay a solid foundation for designing the concentrator of uniform irradiation.
基金This work was supported by the National Key Programme for S&T Research and Development(No.2016YFA0400400)the Youth Innovation Promotion Association CAS(2019016).
文摘Positron sources are one of the most important components of the injector of a circular electron positron collector(CEPC).The CEPC is designed as an e^(+)e^(−)collider for a Higgs factory.Its accelerator system is composed of 100-km-long storage rings and an injector.The design goal of the positron source is to obtain positron beams with a bunch charge of 3 nC.The flux concentrator(FC)is one of the cores of the positron source.This paper reports the design,development,and measurements of an FC prototype system.The prototype includes an FC and an all-solid-state high-current pulse modulator.Preliminary tests show that the peak current on the FC can reach 15.5 kA,and the peak magnetic field can reach 6.2 T.The test results are consistent with the theoretical simulation.The FC system fulfills the requirements of the CEPC positron source as well as provides a reference for the development of similar devices both domestically and abroad.
文摘This paper describes various aspects of the design methodology and heat transfer calculations for an elevated linear absorber. The absorber is a part of the linear Fresnel reflector solar concentrator system, in which hot fluid is generated. The design of the absorber is an inverted trapezoidal air cavity with a glass cover enclosing a multi tube absorber. In a trapezoidal cavity absorber, a set of linear multi tube absorber with plate(named as "plane surface") and without plate(named as "tube surface") underneath are considered. An analytical simulation is done for different gaps between the tubes and for different depths of the cavity. A better design of the absorber is found out to maximize the heat transfer rate supplied to the absorber tube fluid. Also, the experimentally obtained overall heat loss coefficients are compared with the analytical values for the considered arrangements of absorber set up and results are discussed in details.
基金Project supported by the Doctoral Initial Fund of Beijing University of Technology,China (Grant No. X0006015201101)the National Natural Science Foundation of China (Grant No. 10804005)
文摘A metal plate cooling model for 400~ single concentrator solar cells was established. The effects of the thickness and the radius of the metal plate, and the air environment on the temperature of the solar cells were analyzed in detail. It is shown that the temperature of the solar cells decreased sharply at the beginning, with the increase in the thickness of the metal plate, and then changed more smoothly. When the radius of the metal plate was 4 cm and the thickness increased to 2 mm or thicker, the temperature of the solar cell basically stabilized at about 53℃. Increasing the radius of the metal plate and the convective transfer coefficient made the temperature of the solar cell decrease remarkably. The effects of A1 and Cu as the metal plate material on cooling were analyzed contrastively, and demonstrated the superiority of A1 material for the cooling system. Furthermore, considering cost reduction, space holding and the stress of the system, we optimized the structural design of the metal plate. The simulated results can be referred to the design of the structure for the metal plate. Finally, a method to devise the structure of the metal plate for single concentrator solar cells was given.
基金supported by the Doctoral Initial Fund of Beijing University of Technology,China(Grant No.X0006015201101)the National Natural Science Foundation of China(Grant Nos.60876006 and 51202007)
文摘A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.
基金State Grid Gansu Electric Power Company Science and Technology Program(Grant No.W24FZ2730008)National Natural Science Foundation of China(Grant No.51767017).
文摘In the background of the low-carbon transformation of the energy structure,the problem of operational uncertainty caused by the high proportion of renewable energy sources and diverse loads in the integrated energy systems(IES)is becoming increasingly obvious.In this case,to promote the low-carbon operation of IES and renewable energy consumption,and to improve the IES anti-interference ability,this paper proposes an IES scheduling strategy that considers CCS-P2G and concentrating solar power(CSP)station.Firstly,CSP station,gas hydrogen doping mode and variable hydrogen doping ratio mode are applied to IES,and combined with CCS-P2G coupling model,the IES low-carbon economic dispatch model is established.Secondly,the stepped carbon trading mechanism is applied,and the sensitivity analysis of IES carbon trading is carried out.Finally,an IES optimal scheduling strategy based on fuzzy opportunity constraints and an IES risk assessment strategy based on CVaR theory are established.The simulation shows that the gas-hydrogen doping model proposed in this paper reduces the operating cost and carbon emission of IES by 1.32%and 7.17%,and improves the carbon benefit by 5.73%;variable hydrogen doping ratio model reduces the operating cost and carbon emission of IES by 3.75%and 1.70%,respectively;CSP stations reduce 19.64%and 38.52%of the operating costs of IES and 1.03%and 1.80%of the carbon emissions of IES respectively compared to equal-capacity photovoltaic and wind turbines;the baseline price of carbon trading of IES and its rate of change jointly affect the carbon emissions of IES;evaluating the anti-interference capability of IES through trapezoidal fuzzy number and weighting coefficients,enabling IES to guarantee operation at the lowest cost.
基金the framework of the IGC SB RAS project(No.0284-2021-0003)supported by the RFFR ofi_m project(No.17-29-05022).
文摘Several conjugate components represent the aquatic ecosystem of Lake Baikal:Baikal water(surface and deep water),groundwater from boreholes,water of numerous Baikal tributaries,cold and hot mineral springs around Lake Baikal,and the Angara River,the only runoff reflecting all this aquatic diversity.River waters in the Baikal region are known to be deficient in some vital elements,including fluorine.This article discusses the features of the fluorine distribution in the water from the conjugate components of the Baikal ecosystem.Fluorine ion concentrations in the water of the Baikal ecosystem was determined using the potentiometric method.The study represents the monitoring that was carried out between 1997 and 2022 years.We determine likely causes of high and low fluorine concentrations in the water from different components,propose and substantiate the fluorine sources,geological and geochemical model of its influx and distribution features in the water of the Baikal ecosystem.
文摘This work aims at the mathematical modeling of a parabolic trough concentrator, the numerical resolution of the resulting equation, as well as the simulation of the heat transfer fluid heating process. To do this, a thermal balance was established for the heat transfer fluid, the absorber and the glass. This allowed us to establish an equation system whose resolution was done by the finite difference method. Then, a computer program was developed to simulate the temperatures of the heat transfer fluid, the absorber tube and the glass as a function of time and space. The numerical resolution made it possible to obtain the temperatures of the heat transfer fluid, the absorber and the glass. The simulation of the fluid heating process was done in one-hour time steps, from six in the morning to six in the afternoon. The results obtained show that the temperature difference between the inlet and the outlet of the sensor is very significant. These results obtained, regarding the variation of the temperatures of the heat transfer fluid, the absorber and the glass, as well as the powers and efficiency of the parabolic trough concentrator and various factors, allow for the improvement of the performances of our prototype.
文摘Conventional concentrator photovoltaics(CPV)face a persistent trade-off between high efficiency and high cost,driven by expensive multi-junction solar cells and complex active cooling systems.This study presents a computational investigation of a novel Multi-Focal Pyramidal Array(MFPA)-based CPV system designed to overcome this limitation.The MFPA architecture employs a geometrically optimized pyramidal concentrator to distribute concen-trated sunlight onto strategically placed,low-cost monocrystalline silicon cells,enabling high efficiency energy capture while passively managing thermal loads.Coupled optical thermal electrical simulations in COMSOL Multiphysics demonstrate a geometric concentration ratio of 120×,with system temperatures maintained below 110℃ under standard 1000 W/m2 Direct Normal Irradiance(DNI).Ray tracing confirms 95%optical efficiency and a concentrated light spot radius of 2.48 mm.Compared with conventional CPV designs,the MFPA improves power-per-cost by 25%and reduces tracking requirements by 50%owing to its wide±15°acceptance angle.These results highlight the MFPA’s potential as a scalable,low-cost,and energy-efficient pathway for expanding solar power generation.
基金supported by the National Key Research and Development Program of China(2022YFA1203700)the National Natural Science Foundation of China(NSFC)(T2488302,62035008 and 62405129)the Natural Science Foundation of Jiangsu Province(BK20233001).
文摘Solar concentrators laterally converge solar energy to the side of architectural glass and are attractive candidates for building-integrated photovoltaics.Present available luminescent-type and scattering-type solar concentrators suffer from omnidirectional waveguide induced low efficiency,coloring/hazing restrained aesthetic quality,and poor compatibility with existing architectural glass.Here,we propose a diffractive solar concentrator via directly coating cholesteric liquid crystal(CLC)layers onto the architectural glass.The stacked CLC layers with submicron lateral periodic alignment enable broadband and unidirectional waveguiding inside the glass,and thus supply a high-efficient platform for transmissive solar energy capturing with merits of high aesthetic quality and economic viability.A 1-inch-diameter prototype powers a 10-mW fan outdoors,and a typical 2-m-wide window is calculated to concentrate solar energy by 50 times.The design is expected to bring a global terawatt-scale green energy supply and billion-ton annual carbon emission reduction,meeting with the sustainable development of human society.
基金supported by the National Natural Science Foundation of China(No.52270119).
文摘The inhibitory effects of zinc oxide nanoparticles(ZnO NPs)and impacts of N-acylhomoserine lactone(AHL)-based quorum sensing(QS)on biological nitrogen removal(BNR)performance have beenwell-investigated.However,the effects of ammonia nitrogen(NH_(4)^(+)-N)concentrations on NP toxicity and AHL regulation have seldom been addressed yet.This study consulted on the impacts of ZnO NPs on BNR systems when high NH_(4)^(+)-N concentrationwas available.The synergistic toxic effects of high-strength NH_(4)^(+)-N(200 mg/L)and ZnO NPs resulted in decreased ammonia oxidation rates and dropped the nitrogen removal efficiencies by 17.5%±0.2%.The increased extracellular polymeric substances(EPS)production was observed in response to the high NH_(4)^(+)-N and ZnO NP stress,which indicated the defensemechanism against the toxic effects in the BNR systemswas stimulated.Furthermore,the regulatory effects of exogenous N-decanoyl-homoserine lactone(C_(10)-HSL)-mediated QS system on NP-stressed BNR systems were revealed to improve the BNR performance under different NH_(4)^(+)-N concentrations.The C_(10)-HSL regulated the intracellular reactive oxygen species levels,denitrification functional enzyme activities,and antioxidant enzyme activities,respectively.This probably synergistically enhanced the defense mechanism against NP toxicity.However,compared to the low NH_(4)^(+)-N concentration of 60 mg/L,the efficacy of C_(10)-HSL was inhibited at high NH_(4)^(+)-N levels of 200 mg/L.The findings provided the significant application potential of QS system for BNR when facing toxic compound shock threats.
基金supported by the HFIPS Director’s Fund(Nos.YZJJQY202204 and 2021YZGH02)the Comprehensive Research Facility for Fusion Technology Program of China(No.2018-000052-73-01-001228)+1 种基金the Natural Science Foundation of Anhui Province(No.2208085MA19)the National Key R&D Program of China(Nos.2017YFE300103 and 2017YFE300503)。
文摘In order to better build the neutral beam injector with negative ion source(NNBI),the pre-research on key technologies has been carried out for the comprehensive research facility for fusion technology(CRFFT).Cesium seeding into negative-ion sources is a prerequisite to obtain the required negative hydrogen ion.The performance of ion source largely depends on the cesium conditions in the source.It is very necessary to quantitatively measure the amount of cesium in the source during the plasma on and off periods(vacuum stage).
基金supported by the Second Tibetan Plateau Scientific Expedition and Research Program of Ministry of Science and Technology of the People's Republic of China[grant number 2022QZKK0101]the Science and Technology Department of the Tibet Program[grant number XZ202301ZY0035G]。
文摘Since meteorological conditions are the main factor driving the transport and dispersion of air pollutants,an accurate simulation of the meteorological field will directly affect the accuracy of the atmospheric chemical transport model in simulating PM_(2.5).Based on the NASM joint chemical data assimilation system,the authors quantified the impacts of different meteorological fields on the pollutant simulations as well as revealed the role of meteorological conditions in the accumulation,maintenance,and dissipation of heavy haze pollution.During the two heavy pollution processes from 10 to 24 November 2018,the meteorological fields were obtained using NCEP FNL and ERA5 reanalysis data,each used to drive the WRF model,to analyze the differences in the simulated PM_(2.5) concentration.The results show that the meteorological field has a strong influence on the concentration levels and spatial distribution of the pollution simulations.The ERA5 group had relatively small simulation errors,and more accurate PM_(2.5) simulation results could be obtained.The RMSE was 11.86𝜇g m^(-3)lower than that of the FNL group before assimilation,and 5.77𝜇g m^(-3)lower after joint assimilation.The authors used the PM_(2.5) simulation results obtained by ERA5 data to discuss the role of the wind field and circulation situation on the pollution process,to analyze the correlation between wind speed,temperature,relative humidity,and boundary layer height and pollutant concentrations,and to further clarify the key formation mechanism of this pollution process.
文摘This study aimed to optimization of the in vitro fertilization system in Cỏ goat oocytes to achieve the maximum possible blastocyst development rate. In Experiment 1, we assessed the effects of IVF media on the in vitro fertilization of Cỏ goat oocytes. There was no significant difference in the cleavage, blastocyst, or hatching rates between TALP-Fert and BO-IVF media. Experiment 2 was performed to assess the concentration of sperm in the in vitro fertilization of Cỏ goat oocytes. The matured Cỏ goat oocytes were fertilized in BO-IVF for four sperm concentrations: 5 × 105, 1 × 106, 2 × 106 and 3 × 106 sperm/ml. The blastocyst rate of 2 × 106 sperm/ml and 3 × 106 sperm/ml groups was higher than that of 5 × 105 sperm/ml and 1 × 106 sperm/ml groups (P Experiment 3 was performed to assess the IVF duration on the in vitro fertilization of Cỏ goat oocytes. The matured Cỏ goat oocytes were fertilized in BO-IVF with sperm concentration of 3 × 106 sperm/ml for 18, 20, 22 and 24 h. The cleavage, blastocyst, and hatching blastocyst rates of 18 h group were lower than those of 20, 22 and 24 h groups (P 0.05). In conclusion, the matured Cỏ goat oocytes were fertilized in BO-IVF with sperm concentration of 3 × 106 sperm/ml for 20 hours, which is suitable for the in vitro Cỏ goat embryo production.
文摘This paper is based on the rainwater collection project in the retrofit of the Dongyi teaching block in Zhejiang University Xixi Campus.The analysis incorporates the local meteorological data, recycling water utilization, and precipitation adjustment.The rainwater collection system in this program also adds the condensation water from the heating, ventilation and air conditioning （ HVAC） system and the concentration from the reverse-osmosis system used for watering greens and supplying waterscapes.By calculating, the quantity of the HVAC condensation water in summer is 3.48 m3/d, and the quantity of the reverse-osmosis concentrated water is 198 to 396 L/d.This method solves the water shortage caused by high evaporation in summer and low precipitation in winter.Supported by empirical monitoring data, the proposed method significantly increases the economic efficiency of the system during the summer period.
