This paper moves one step forward to build?a?numerical model to research quantitative characterization and dynamic law for interlayer interference factor (IIF) in the multilayer reservoir which was heavy oil reservoir...This paper moves one step forward to build?a?numerical model to research quantitative characterization and dynamic law for interlayer interference factor (IIF) in the multilayer reservoir which was heavy oil reservoirs and produced by directional wells. There are mainly four contributions of this paper to the existing body of literature. Firstly, an equivalent simulation method of the pseudo start pressure gradient (PSPG) is developed to quantitatively predict the value of?IIF?under different geological reservoir conditions. Secondly, the interlayer interference is extended in time, and the time period of the study extends from a water cut stage to the whole process from the oil well open to produce?a?high water cut. Thirdly, besides the conventional productivity interlayer interference factor (PIIF), a new parameter, that is, the oil recovery interlayer interference factor (RIIF) is put forward.?RIIF?can be used to evaluate the technical indexes of stratified development and multilayer co-production effectively. Fourthly,?the?effectsof various geological reservoir parameters such as reservoir permeability and crude oil viscosity, etc. on the?PIIF?and?RIIF’s?type curves?are?discussed in detail and the typical plate?is?plotted. The research results provide a foundation for the effective development of multilayer heavy oil reservoirs.展开更多
Existing evaluation methods used for the development area selection for commingled production of tight gas and coalbed methane(CBM)are poorly universal and their parameters(e.g.reserves and reservoir physical properti...Existing evaluation methods used for the development area selection for commingled production of tight gas and coalbed methane(CBM)are poorly universal and their parameters(e.g.reserves and reservoir physical properties)cannot reflect the production rate difference during commingled production of tight gas and CBM.In this paper,an integrated evaluation coefficient used for evaluating favorable commingled production areas of tight gas and CBM was defined so as to establish a universal quantitative evaluation index system.Then,by means of orthogonal design together with numerical simulation,the key parameters influencing the commingled production rate and their influence degree on the production rate were determined by taking the commingled production rate as the evaluation target.Finally,a new quantitative evaluation method for the development area selection for commingled production of tight gas and CBM was established.And the following research results were obtained.First,by virtue of the new quantitative evaluation method,the geological occurrence model of tight gas and CBM,the key evaluation parameter and the orthogonal experiment design are established,and the influence degree of evaluation parameters on production rate and the integrated evaluation coefficient of favorable commingled production area of tight gas and CBM are determined.Second,the quantitative evaluation results on the development areas of commingled production of tight gas and CBM in KNW Block based on 12 selected key parameters show that the southern KNW Block and the Well block KNW-37 in the north of KNW Block are the favorable areas for single production of tight gas,Well blocks KNW-10,KNW-33 and KNW-9 are the favorable areas for single production of CBM,and the central and southwestern areas are the favorable areas for the commingled production of tight gas and CBM.In conclusion,this new quantitative evaluation method is universal and can be used as reference for the development area selection for commingled production of tight gas and CBM.展开更多
Traditional fluid production profile logging is not usually suitable for heavy-viscous crude oil wells.Biodegradation of heavy oil can lead to the loss of n-alkanes,and the use of chromatogram fingerprint techniques i...Traditional fluid production profile logging is not usually suitable for heavy-viscous crude oil wells.Biodegradation of heavy oil can lead to the loss of n-alkanes,and the use of chromatogram fingerprint techniques in studying the production contributions of single layers in heavy oil commingled wells has limitations.However,aromatic compounds are relatively well preserved.We took the heavy oil commingled wells of small layers NG55 and NG61 in the ninth area of the Gudong oil field as examples.Based on the principle of chromatography,the whole-oil GC-MS was used,and the aromatic parameters which have a strongly linear relationship with the ratio of mixed two end member oils were verified and selected in laboratory.Studies showed that the ratio of （1,4,6-＋ 2,3,6-trimethylnaphthalene） to 1,2,5-trimethylnaphthalene has a strongly linear relationship with the ratio of the mixed two end member oils （R2=0.992）.The oil contributions from single layers NG55 and NG61 in six commingled heavy oil wells were calculated using established charts and this relationship.The calculated results are consistent with the results of long period dynamic monitoring and logging interpretation in the study area and can provide a scientific basis for monitoring production performance and hierarchical management of reservoirs.The study provides a new geochemical method for calculation of the contributions of single layers in heavy oil commingled wells when conventional fluid production profile logging is not suitable.展开更多
Hydraulic fracturing and commingle production of multiple layers are extensively adopted in unconventional tight gas reservoirs.Accurate determination of parameters of individual layers in multilayered tight gas reser...Hydraulic fracturing and commingle production of multiple layers are extensively adopted in unconventional tight gas reservoirs.Accurate determination of parameters of individual layers in multilayered tight gas reservoirs is essential for well performance evaluation and development strategy optimization.However,most analytical models for fractured vertical wells in stratified gas reservoirs focus on fully penetrated hydraulic fractures,neglecting the influence of partial penetration of hydraulic fractures.This paper presents a semi-analytical model to investigate the transient pressure behavior of vertically fractured wells in dual porosity multi-layered tight gas reservoirs.The partial penetration of hydraulic fracture,the vertical heterogeneities of layer properties,the differences between hydraulic fracture lengths in each layer and the stress sensitivity are all incorporated in the proposed model.The point-source solution,Laplace transformation,Fourier transformation,Pedrosa's transformation,perturbation technique,and the superposition principle are applied to obtain the analytical solution of transient pressure responses.The proposed model is validated against a commercial software,and the transient pressure behavior of vertically fractured wells in multi-layered tight gas reservoirs are analyzed.Based on the characteristics of the type curves,seven flow regimes can be identified,including wellbore storage,transitional flow period,reservoir linear flow period,vertical pseudo-radial flow in fracture system,inter-porosity flow period,late-time pseudo-radial flow period,and the boundary-dominated flow period.Sensitivity analyses reveal that the penetration ratio of hydraulic fracture has primary influence on early-time transient pressure behavior and production contribution,while the stress sensitivity mainly affects the late-time transient pressure behavior.Gas production at the initial stage is mainly contributed by the high-pressure/high-permeability layer,and gas backflow will occur during initial production stage for obviously unequal initial formation pressures.Finally,two field cases are conducted to illustrate the applicability of the proposed model.The model and corresponding conclusions can provide technical support for performance analysis of tight gas reservoirs.展开更多
Human-made and natural disasters can result in severely fragmented,compromised,and commingled human remains.The related disaster victim identification(DVI)operations are invariably challenging,with the state of the re...Human-made and natural disasters can result in severely fragmented,compromised,and commingled human remains.The related disaster victim identification(DVI)operations are invariably challenging,with the state of the remains potentially precluding some identifications.Practitioners involved in these DVI operations will routinely face logistical,practical,and ethical challenges.This review provides information and guidance derived from firsthand experiences to individuals tasked with managing DVI operations with fragmented human remains.We outline several key issues that should be addressed during disaster preparedness planning and at the outset of an operation,when incident-specific strategies are developed.Specific challenges during recovery and examination of fragmented remains are addressed,highlighting the importance of experienced specialists at the scene and in the mortuary.DNA sample selection and sampling techniques are reviewed,as well as downstream effects of commingling and contamination,which can complicate reconciliation and emphasise the need for rigorous quality control.We also touch on issues that may arise during communication with families.While recommendations are provided,they are not intended as proscriptive policy but rather as an addition to the general recommendations given in the International Criminal Police Organization(INTERPOL)DVI Guide,to inform preparative discussions between government officials,judiciary,police,and forensic specialists.展开更多
Based on the productivity equation of coalbed methane(CBM) wells, three indexes, main production layer optimization index, main production layer expansion index and capacity contribution index are proposed, with which...Based on the productivity equation of coalbed methane(CBM) wells, three indexes, main production layer optimization index, main production layer expansion index and capacity contribution index are proposed, with which the three-step optimization method of production-layer combination is established. In selecting main production layer, the coal seam thickness, CBM content, coal seam permeability, coal seam reservoir pressure and coal structure are considered comprehensively to evaluate the potential of the production layer. In selecting expansion of the main production layer combination, on the premise of ensuring full and slow desorption of the main production layer and non-exposure of the main production layer out of liquid surface, the degree of mutual interference between the main and non-main production layers is comprehensively evaluated by coupling the critical desorption pressure, layer spacing and reservoir pressure gradient difference. In optimizing production layer combination, the main concern is the economic efficiency of the combined layers. Only when the contribution coefficient of the main production layer is greater than 30% and the contribution index of the other production layers is more than 10%, the economic benefit of a CBM well after being put into production can be ensured. Based on the comparative analysis of the development effect of the development test wells in Songhe of Guizhou province, it is proved that the "three-step method" for the optimization of production-layer combination is scientific and practical, and can be used to design the multi-layer commingling scheme of coalbed methane.展开更多
A thermoplastic based composite material is suitable for automobile and aerospace applications. The recyclability of thermoplastic and clean processing further enhance its use. The only limitation encountered in using...A thermoplastic based composite material is suitable for automobile and aerospace applications. The recyclability of thermoplastic and clean processing further enhance its use. The only limitation encountered in using this material is its high-melt viscosity. Various techniques have been developed to overcome this problem. Commingled materials are one of such methods adopted for making proper use of thermoplastic. A major problem observed during the use of a commingled material is its de-commingling, wherein, the uniform distribution of fiber and thermoplastic yam gets disturbed and affects the final quality of the composite. The effects of the braiding process on laminate quality were investigated. Flat plaques were produced by braiding the commingled yam, using a 48- carrier braiding machine. The braids （and control woven samples） were subsequently heated and consolidated in a nonisothermal compression molding operation. Prior to the manufacture of the ＇best quality＇ plaques, a series of moldings were produced under different consolidation conditions, to study the dependence of properties on the process variables. This enabled a processing window to be established for each material and helped to separate the respective effects of yam handling, textile processing, and consolidation on laminate properties.展开更多
The use of maleic anhydride (MA) coupling agent in polypropylene (PP) matrix system is promising technique to enhance the fibre-matrix interface in composite applications. However, most of the previous studies are foc...The use of maleic anhydride (MA) coupling agent in polypropylene (PP) matrix system is promising technique to enhance the fibre-matrix interface in composite applications. However, most of the previous studies are focused on either treatment of the natural fibres or the PP matrix with this coupling agent, which are not commercially viable. In this work, a cost-effective technique “hybrid yarns” was used to manufacture commingled reinforcing flax fibres and MA-grafted PP matrix fibres. Two types of twist-less flax/PP and flax/MAPP hybrid yarns were produced containing 40% flax and 60% matrix fibres by volume. Both PP and MAPP fibres were thermally and rheologically characterised using DSC, MFI, TGA, DTA and capillary rheometer. It is found that the composites manufactured from flax/MAPP blends exhibited 15% higher strength and 25% higher modulus compared to those made of flax/PP. This was due to the improved flax/matrix interface, the higher melt flow rate and lower share viscosity behaviour of the MAPP matrix fibres compared to the standard PP fibres used.展开更多
The existing models for calculating the water breakthrough time of gas wells in gas reservoirs with edge water ignore the effects of reservoir's interlayer heterogeneity,so their calculation results are more devia...The existing models for calculating the water breakthrough time of gas wells in gas reservoirs with edge water ignore the effects of reservoir's interlayer heterogeneity,so their calculation results are more deviated from the actual water breakthrough time of gas wells.As a result,they cannot accurately and effectively guide the adjustment of gas well production system and the formulation of technical water control measures.In this paper,a water-flooding seepage experiment of parallel core was conducted by taking the gas reservoir with edge water of Lower Triassic Feixianguan Formation in the Puguang Gas Field of the Sichuan Basin as an example.Then,the effects of edge water inrush caused by the interlayer heterogeneity of reservoir on water breakthrough time of gas wells was analyzed by means of reservoir numerical simulation.Based on this,the inrush coefficient was introduced to characterize the interlayer heterogeneity of reservoir,and a model for calculating the water breakthrough time of gas wells in the commingled gas reservoir with edge water considering the influence of interlayer heterogeneity was established.Finally,five wells in the gas reservoir of Feixianguan Formation in the Puguang Gas Field were selected for case calculation.And the following research results were obtained.First,the interlayer heterogeneity of gas reservoir results in edge water burst.And the stronger the interlayer heterogeneity,the more severe the edge water coning and the sooner the water breakthrough.The water breakthrough time of gas wells depends on the water breakthrough time in the reservoir with the highest permeability.Second,a model for calculating the water breakthrough time of gas wells in the gas reservoirs with edge water considering the influence of reservoir interlayer heterogeneity is established based on the seepage theory.And the relative errors of its calculation results are in the range of 3.43e4.70%,which can satisfy the accuracy requirement of engineering errors.In conclusion,this newly established model can provide an effective method for accurately calculating the water break-through time of the gas well in the commingled gas reservoir with edge water.Furthermore,it is conducive to the adjustment of the production system of gas wells in the gas reservoir with edge water and the formulation of technical water control measures.展开更多
Gas drainage is carried out based on output from each coal bed throughout commingling production of coalbed methane(CBM).A reasonable drainage process should therefore initially guarantee main coal bed production and ...Gas drainage is carried out based on output from each coal bed throughout commingling production of coalbed methane(CBM).A reasonable drainage process should therefore initially guarantee main coal bed production and then enhance gas output from other beds.Permanent damage can result if this is not the case,especially with regard to fracture development in the main gas-producing coal bed and can greatly reduce single well output.Current theoretical models and measuring devices are inapplicable to commingled CBM drainage,however,and so large errors in predictive models cannot always be avoided.The most effective currently available method involves directly measuring gas output from each coal bed as well as determining the dominant gas-producing unit.A dynamic evaluation technique for gas output from each coal bed during commingling CBM production is therefore proposed in this study.This technique comprises a downhole measurement system combined with a theoretical calculation model.Gas output parameters(i.e.,gas-phase flow rate,temperature,pressure)are measured in this approach via a downhole measurement system;substituting these parameters into a deduced theoretical calculation model then means that gas output from each seam can be calculated to determine the main gas-producing unit.Trends in gas output from a single well or each seam can therefore be predicted.The laboratory and field test results presented here demonstrate that calculation errors in CBM outputs can be controlled within a margin of 15%and therefore conform with field use requirements.展开更多
An abnormality tends to occur in the productivity indicative curves in the process of productivity test interpretation of multi-layer gas wells,resulting in the failure of solutions to their productivity equations and...An abnormality tends to occur in the productivity indicative curves in the process of productivity test interpretation of multi-layer gas wells,resulting in the failure of solutions to their productivity equations and absolute open flow rates.To figure out the reasons for such an abnormality,we established a full-hole calculation model considering the coupling of wellbore variable mass flows and reservoir seepages to calculate a gas production profile and wellbore pressure distribution of a multi-layer productive gas reservoir.Then,based on the analysis of the gas production profile and wellbore pressure distribution characteristics of gas wells at different gas production rates,the root cause for the abnormality in the productivity indicative curves of multi-layer gas wells was analyzed,and a corresponding correction method was proposed and validated based on some examples.And the following research results were obtained.First,there are two reasons for the abnormal productivity indicative curves of multi-layer gas wells.On the one hand,there is a variable mass pipe flow in the wellbore of multi-layer sections and a flowing pressure gradient decreases with the increase of well depth.And the flowing pressure in the middle of the reservoir which is converted based on the flowing pressure gradient above the pressure gauge is higher than the real value.On the other hand,the pressure in the multi-layer producing sections doesn't realize a balance after well shutdown for a short time,so the measured static pressure is greater than the one measured when the pressure of each layer gets balanced after well shutdown for a long time.Second,the flowing pressure obtained from the productivity test interpretation of multi-layer gas producer shall be converted based on the pressure measured by the pressure gauge within 200 m above the reservoir top and it is necessary to adopt the static pressure measured after the balance of wellbore pressure.Third,the reliability of the model,the rationality of the abnormality reason analysis and the validity of the correction method are verified based on calculation examples and cases.It is concluded that the research results provide a technical support for the productivity evaluation of multi-layer gas wells.展开更多
文摘This paper moves one step forward to build?a?numerical model to research quantitative characterization and dynamic law for interlayer interference factor (IIF) in the multilayer reservoir which was heavy oil reservoirs and produced by directional wells. There are mainly four contributions of this paper to the existing body of literature. Firstly, an equivalent simulation method of the pseudo start pressure gradient (PSPG) is developed to quantitatively predict the value of?IIF?under different geological reservoir conditions. Secondly, the interlayer interference is extended in time, and the time period of the study extends from a water cut stage to the whole process from the oil well open to produce?a?high water cut. Thirdly, besides the conventional productivity interlayer interference factor (PIIF), a new parameter, that is, the oil recovery interlayer interference factor (RIIF) is put forward.?RIIF?can be used to evaluate the technical indexes of stratified development and multilayer co-production effectively. Fourthly,?the?effectsof various geological reservoir parameters such as reservoir permeability and crude oil viscosity, etc. on the?PIIF?and?RIIF’s?type curves?are?discussed in detail and the typical plate?is?plotted. The research results provide a foundation for the effective development of multilayer heavy oil reservoirs.
基金supported by the Comprehensive Research Project of CNOOC Research Institute“Overseas Shale Oil and Gas Productivity Evaluation Technology and Method”(No.:YXKY-2016-ZY-03).
文摘Existing evaluation methods used for the development area selection for commingled production of tight gas and coalbed methane(CBM)are poorly universal and their parameters(e.g.reserves and reservoir physical properties)cannot reflect the production rate difference during commingled production of tight gas and CBM.In this paper,an integrated evaluation coefficient used for evaluating favorable commingled production areas of tight gas and CBM was defined so as to establish a universal quantitative evaluation index system.Then,by means of orthogonal design together with numerical simulation,the key parameters influencing the commingled production rate and their influence degree on the production rate were determined by taking the commingled production rate as the evaluation target.Finally,a new quantitative evaluation method for the development area selection for commingled production of tight gas and CBM was established.And the following research results were obtained.First,by virtue of the new quantitative evaluation method,the geological occurrence model of tight gas and CBM,the key evaluation parameter and the orthogonal experiment design are established,and the influence degree of evaluation parameters on production rate and the integrated evaluation coefficient of favorable commingled production area of tight gas and CBM are determined.Second,the quantitative evaluation results on the development areas of commingled production of tight gas and CBM in KNW Block based on 12 selected key parameters show that the southern KNW Block and the Well block KNW-37 in the north of KNW Block are the favorable areas for single production of tight gas,Well blocks KNW-10,KNW-33 and KNW-9 are the favorable areas for single production of CBM,and the central and southwestern areas are the favorable areas for the commingled production of tight gas and CBM.In conclusion,this new quantitative evaluation method is universal and can be used as reference for the development area selection for commingled production of tight gas and CBM.
基金supported by the Gudong Oil Production Plant of Shengli Oilfield Subsidiary Company,China Postdoctoral Science Foundation(Project 2013M530681)Hubei Province Natural Science Foundation(Project 2013CFB394)
文摘Traditional fluid production profile logging is not usually suitable for heavy-viscous crude oil wells.Biodegradation of heavy oil can lead to the loss of n-alkanes,and the use of chromatogram fingerprint techniques in studying the production contributions of single layers in heavy oil commingled wells has limitations.However,aromatic compounds are relatively well preserved.We took the heavy oil commingled wells of small layers NG55 and NG61 in the ninth area of the Gudong oil field as examples.Based on the principle of chromatography,the whole-oil GC-MS was used,and the aromatic parameters which have a strongly linear relationship with the ratio of mixed two end member oils were verified and selected in laboratory.Studies showed that the ratio of （1,4,6-＋ 2,3,6-trimethylnaphthalene） to 1,2,5-trimethylnaphthalene has a strongly linear relationship with the ratio of the mixed two end member oils （R2=0.992）.The oil contributions from single layers NG55 and NG61 in six commingled heavy oil wells were calculated using established charts and this relationship.The calculated results are consistent with the results of long period dynamic monitoring and logging interpretation in the study area and can provide a scientific basis for monitoring production performance and hierarchical management of reservoirs.The study provides a new geochemical method for calculation of the contributions of single layers in heavy oil commingled wells when conventional fluid production profile logging is not suitable.
基金supported by the National Natural Science Foundation of China(Grant Nos.52174036,52234003)the Sichuan Province Science and Technology Program(Grant No.2024NSFSC0199)the Joint Fund for Innovation and Development of Chongqing Natural Science Foundation(Grant No.2023NSCQ-LZX0184).
文摘Hydraulic fracturing and commingle production of multiple layers are extensively adopted in unconventional tight gas reservoirs.Accurate determination of parameters of individual layers in multilayered tight gas reservoirs is essential for well performance evaluation and development strategy optimization.However,most analytical models for fractured vertical wells in stratified gas reservoirs focus on fully penetrated hydraulic fractures,neglecting the influence of partial penetration of hydraulic fractures.This paper presents a semi-analytical model to investigate the transient pressure behavior of vertically fractured wells in dual porosity multi-layered tight gas reservoirs.The partial penetration of hydraulic fracture,the vertical heterogeneities of layer properties,the differences between hydraulic fracture lengths in each layer and the stress sensitivity are all incorporated in the proposed model.The point-source solution,Laplace transformation,Fourier transformation,Pedrosa's transformation,perturbation technique,and the superposition principle are applied to obtain the analytical solution of transient pressure responses.The proposed model is validated against a commercial software,and the transient pressure behavior of vertically fractured wells in multi-layered tight gas reservoirs are analyzed.Based on the characteristics of the type curves,seven flow regimes can be identified,including wellbore storage,transitional flow period,reservoir linear flow period,vertical pseudo-radial flow in fracture system,inter-porosity flow period,late-time pseudo-radial flow period,and the boundary-dominated flow period.Sensitivity analyses reveal that the penetration ratio of hydraulic fracture has primary influence on early-time transient pressure behavior and production contribution,while the stress sensitivity mainly affects the late-time transient pressure behavior.Gas production at the initial stage is mainly contributed by the high-pressure/high-permeability layer,and gas backflow will occur during initial production stage for obviously unequal initial formation pressures.Finally,two field cases are conducted to illustrate the applicability of the proposed model.The model and corresponding conclusions can provide technical support for performance analysis of tight gas reservoirs.
文摘Human-made and natural disasters can result in severely fragmented,compromised,and commingled human remains.The related disaster victim identification(DVI)operations are invariably challenging,with the state of the remains potentially precluding some identifications.Practitioners involved in these DVI operations will routinely face logistical,practical,and ethical challenges.This review provides information and guidance derived from firsthand experiences to individuals tasked with managing DVI operations with fragmented human remains.We outline several key issues that should be addressed during disaster preparedness planning and at the outset of an operation,when incident-specific strategies are developed.Specific challenges during recovery and examination of fragmented remains are addressed,highlighting the importance of experienced specialists at the scene and in the mortuary.DNA sample selection and sampling techniques are reviewed,as well as downstream effects of commingling and contamination,which can complicate reconciliation and emphasise the need for rigorous quality control.We also touch on issues that may arise during communication with families.While recommendations are provided,they are not intended as proscriptive policy but rather as an addition to the general recommendations given in the International Criminal Police Organization(INTERPOL)DVI Guide,to inform preparative discussions between government officials,judiciary,police,and forensic specialists.
基金Supported by the China National Science and Technology Major Project(2016ZX05044-002)the National Natural Science Foundation of China(41772155)the Fundamental Research Funds for the Central Universities of China(No.2015XKZD07)
文摘Based on the productivity equation of coalbed methane(CBM) wells, three indexes, main production layer optimization index, main production layer expansion index and capacity contribution index are proposed, with which the three-step optimization method of production-layer combination is established. In selecting main production layer, the coal seam thickness, CBM content, coal seam permeability, coal seam reservoir pressure and coal structure are considered comprehensively to evaluate the potential of the production layer. In selecting expansion of the main production layer combination, on the premise of ensuring full and slow desorption of the main production layer and non-exposure of the main production layer out of liquid surface, the degree of mutual interference between the main and non-main production layers is comprehensively evaluated by coupling the critical desorption pressure, layer spacing and reservoir pressure gradient difference. In optimizing production layer combination, the main concern is the economic efficiency of the combined layers. Only when the contribution coefficient of the main production layer is greater than 30% and the contribution index of the other production layers is more than 10%, the economic benefit of a CBM well after being put into production can be ensured. Based on the comparative analysis of the development effect of the development test wells in Songhe of Guizhou province, it is proved that the "three-step method" for the optimization of production-layer combination is scientific and practical, and can be used to design the multi-layer commingling scheme of coalbed methane.
文摘A thermoplastic based composite material is suitable for automobile and aerospace applications. The recyclability of thermoplastic and clean processing further enhance its use. The only limitation encountered in using this material is its high-melt viscosity. Various techniques have been developed to overcome this problem. Commingled materials are one of such methods adopted for making proper use of thermoplastic. A major problem observed during the use of a commingled material is its de-commingling, wherein, the uniform distribution of fiber and thermoplastic yam gets disturbed and affects the final quality of the composite. The effects of the braiding process on laminate quality were investigated. Flat plaques were produced by braiding the commingled yam, using a 48- carrier braiding machine. The braids （and control woven samples） were subsequently heated and consolidated in a nonisothermal compression molding operation. Prior to the manufacture of the ＇best quality＇ plaques, a series of moldings were produced under different consolidation conditions, to study the dependence of properties on the process variables. This enabled a processing window to be established for each material and helped to separate the respective effects of yam handling, textile processing, and consolidation on laminate properties.
文摘The use of maleic anhydride (MA) coupling agent in polypropylene (PP) matrix system is promising technique to enhance the fibre-matrix interface in composite applications. However, most of the previous studies are focused on either treatment of the natural fibres or the PP matrix with this coupling agent, which are not commercially viable. In this work, a cost-effective technique “hybrid yarns” was used to manufacture commingled reinforcing flax fibres and MA-grafted PP matrix fibres. Two types of twist-less flax/PP and flax/MAPP hybrid yarns were produced containing 40% flax and 60% matrix fibres by volume. Both PP and MAPP fibres were thermally and rheologically characterised using DSC, MFI, TGA, DTA and capillary rheometer. It is found that the composites manufactured from flax/MAPP blends exhibited 15% higher strength and 25% higher modulus compared to those made of flax/PP. This was due to the improved flax/matrix interface, the higher melt flow rate and lower share viscosity behaviour of the MAPP matrix fibres compared to the standard PP fibres used.
基金Project supported by the National Science and Technology Major Project“Research on Gas-Water Two-Phase Flow Characteristics of Deep Reef-Shoal Reservoirs”(No.2016ZX05017-001-HZ02)Chongqing Graduate Research and Innovation Project“Water Invasion Mechanism and Prediction Model of Water Breakthrough Time of Ultra-Deep Carbonate Gas Reservoirs”(No.CYS19351)。
文摘The existing models for calculating the water breakthrough time of gas wells in gas reservoirs with edge water ignore the effects of reservoir's interlayer heterogeneity,so their calculation results are more deviated from the actual water breakthrough time of gas wells.As a result,they cannot accurately and effectively guide the adjustment of gas well production system and the formulation of technical water control measures.In this paper,a water-flooding seepage experiment of parallel core was conducted by taking the gas reservoir with edge water of Lower Triassic Feixianguan Formation in the Puguang Gas Field of the Sichuan Basin as an example.Then,the effects of edge water inrush caused by the interlayer heterogeneity of reservoir on water breakthrough time of gas wells was analyzed by means of reservoir numerical simulation.Based on this,the inrush coefficient was introduced to characterize the interlayer heterogeneity of reservoir,and a model for calculating the water breakthrough time of gas wells in the commingled gas reservoir with edge water considering the influence of interlayer heterogeneity was established.Finally,five wells in the gas reservoir of Feixianguan Formation in the Puguang Gas Field were selected for case calculation.And the following research results were obtained.First,the interlayer heterogeneity of gas reservoir results in edge water burst.And the stronger the interlayer heterogeneity,the more severe the edge water coning and the sooner the water breakthrough.The water breakthrough time of gas wells depends on the water breakthrough time in the reservoir with the highest permeability.Second,a model for calculating the water breakthrough time of gas wells in the gas reservoirs with edge water considering the influence of reservoir interlayer heterogeneity is established based on the seepage theory.And the relative errors of its calculation results are in the range of 3.43e4.70%,which can satisfy the accuracy requirement of engineering errors.In conclusion,this newly established model can provide an effective method for accurately calculating the water break-through time of the gas well in the commingled gas reservoir with edge water.Furthermore,it is conducive to the adjustment of the production system of gas wells in the gas reservoir with edge water and the formulation of technical water control measures.
基金This research was funded by grants from the Natural Science Foundation in Hubei(2018CFB349)the National Natural Sciences Foundation of China(41672155,61733016)Open Research Fund Program of Key Laboratory of Tectonics and Petroleum Resources Ministry of Education(No.TPR-2018-10).
文摘Gas drainage is carried out based on output from each coal bed throughout commingling production of coalbed methane(CBM).A reasonable drainage process should therefore initially guarantee main coal bed production and then enhance gas output from other beds.Permanent damage can result if this is not the case,especially with regard to fracture development in the main gas-producing coal bed and can greatly reduce single well output.Current theoretical models and measuring devices are inapplicable to commingled CBM drainage,however,and so large errors in predictive models cannot always be avoided.The most effective currently available method involves directly measuring gas output from each coal bed as well as determining the dominant gas-producing unit.A dynamic evaluation technique for gas output from each coal bed during commingling CBM production is therefore proposed in this study.This technique comprises a downhole measurement system combined with a theoretical calculation model.Gas output parameters(i.e.,gas-phase flow rate,temperature,pressure)are measured in this approach via a downhole measurement system;substituting these parameters into a deduced theoretical calculation model then means that gas output from each seam can be calculated to determine the main gas-producing unit.Trends in gas output from a single well or each seam can therefore be predicted.The laboratory and field test results presented here demonstrate that calculation errors in CBM outputs can be controlled within a margin of 15%and therefore conform with field use requirements.
文摘An abnormality tends to occur in the productivity indicative curves in the process of productivity test interpretation of multi-layer gas wells,resulting in the failure of solutions to their productivity equations and absolute open flow rates.To figure out the reasons for such an abnormality,we established a full-hole calculation model considering the coupling of wellbore variable mass flows and reservoir seepages to calculate a gas production profile and wellbore pressure distribution of a multi-layer productive gas reservoir.Then,based on the analysis of the gas production profile and wellbore pressure distribution characteristics of gas wells at different gas production rates,the root cause for the abnormality in the productivity indicative curves of multi-layer gas wells was analyzed,and a corresponding correction method was proposed and validated based on some examples.And the following research results were obtained.First,there are two reasons for the abnormal productivity indicative curves of multi-layer gas wells.On the one hand,there is a variable mass pipe flow in the wellbore of multi-layer sections and a flowing pressure gradient decreases with the increase of well depth.And the flowing pressure in the middle of the reservoir which is converted based on the flowing pressure gradient above the pressure gauge is higher than the real value.On the other hand,the pressure in the multi-layer producing sections doesn't realize a balance after well shutdown for a short time,so the measured static pressure is greater than the one measured when the pressure of each layer gets balanced after well shutdown for a long time.Second,the flowing pressure obtained from the productivity test interpretation of multi-layer gas producer shall be converted based on the pressure measured by the pressure gauge within 200 m above the reservoir top and it is necessary to adopt the static pressure measured after the balance of wellbore pressure.Third,the reliability of the model,the rationality of the abnormality reason analysis and the validity of the correction method are verified based on calculation examples and cases.It is concluded that the research results provide a technical support for the productivity evaluation of multi-layer gas wells.
