We consider a profound problem of two-point resistance in the resistor network with a null resistor edge and an arbitrary boundary,which has not been solved before because the Green＇s function technique and the Lapla...We consider a profound problem of two-point resistance in the resistor network with a null resistor edge and an arbitrary boundary,which has not been solved before because the Green＇s function technique and the Laplacian matrix approach are invalid in this case.Looking for the exact solutions of resistance is important but difficult in the case of the arbitrary boundary since the boundary is a wall or trap which affects the behavior of a finite network.In this paper,we give a general resistance formula that is composed of a single summation by using the recursion-transform method.Meanwhile,several interesting results are derived by the general formula.Further,the current distribution is given explicitly as a byproduct of the method.展开更多
A wideband metamaterial absorber （MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loa...A wideband metamaterial absorber （MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loaded with lumped resistors, a dielectric substrate, and a metal plate. We simulated, fabricated, measured, and analyzed the MA. The experimental results show that the reflectance （S11） is below -10 dB at normal incidence in the frequency range of 7.7 GHz 18 GHz, and the peak value is about -20 dB. Simulated power loss density distributions indicate that wideband absorption of the MA is mainly attributable to the lumped resistors in the magnetic resonator. Further investigations indicate that the distance between two unit cells along the magnetic field direction significantly influences the performance of the MA.展开更多
Phenolic formaldehyde(PF)and epoxy(EP)resins are commonly used in electronic packaging. In this paper, high-ohmic resistors(2.2 M?, ±0.5%,)with Cr-Si film were coated by PF/EP paint, and the resulting coated resi...Phenolic formaldehyde(PF)and epoxy(EP)resins are commonly used in electronic packaging. In this paper, high-ohmic resistors(2.2 M?, ±0.5%,)with Cr-Si film were coated by PF/EP paint, and the resulting coated resistors were used for heat and humid(HH)experiments. The experimental results show that the corrosion of bandlike resistive films is selective and isotropic, and that the corrosion spots in resistive films all form along grooves and extend in the same direction. It is revealed that OH^- ions are generated due to the electrochemical reactions of resistive film in HH experiments, so a NaOH aqueous solution with pH about 10 was used to study the effects of absorbed water and OH^- ions on PF/EP polymer film. The results indicates that the color of some part on PF/EP polymer film changes due to corrosion, and that the corrosion part of the polymer film is easy to be peeled off. It can be inferred that OH^- ions generated in HH experiments may play a catalytic role in the chemical reactions between polymer film and the absorbed water, which accelerates the degradation of PF/EP protection film for a resistor.展开更多
IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·...IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·cm by the IrO2 intermixing ratio from 0.55 to 0.78 in the IrO2-TiO2 thin films. The low temperature coefficient of resistance（TCR） values can be obtained by adopting IrO2-TiO2 composite thin films. Moreover, the change in the resistivity of IrO2-TiO2 thin films was below 10% even after O2 annealing process at 600 ℃. The step stress test results show that IrO2-TiO2 films have better characteristics than conventional TaN08 heater resistor. Therefore, IrO2-TiO2 composite thin films can be used as a heater resistor material in thermal inkjet printhead.展开更多
High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than...High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than ±15×10-6/℃.Cr-Si-Ta-Al films were prepared with Ar flow rate and sputtering power fixed at 20 standard-state cubic centimeter per minute(sccm) and 100 W,respectively.The experiment shows that the electrical properties of Cr-SiTa-Al deposition films can meet the specification requirements of 0603 ty...展开更多
Results of investigation of X-ray diffraction, infrared and optical spectra of powders of the ruthenium dioxide, lead-silicate glass as well as their mixture before and after sintering are reported. Sintering conditio...Results of investigation of X-ray diffraction, infrared and optical spectra of powders of the ruthenium dioxide, lead-silicate glass as well as their mixture before and after sintering are reported. Sintering conditions typical for thick film resistors were used. Intensity of main lines of RuO2 in X-ray diffraction patterns of sintered mixtures decreases and they slightly shift towards small angles. No new reflexes appear in these patterns. Absorbance of RuO2 in the range of 2.5-100 μm is proportional to and featureless. Infrared spectrum of lead-silicate glass has absorption bands of [SiO4]4- tetrahedra and Pb-O bonds only. Optical spectrum of RuO2 has wide absorption bands at 950 and 370 nm. Spectra of the mixture of RuO2 and glass powders before and after sintering are different indicating that there is interaction between them during the sintering process. Concentration of free charge carriers estimated from the optical spectra is about 1021 cm-3.展开更多
Current dependence and stability of the measured resistance value are very important for the accurate measurement of DC standard resistor. In this paper, the volt-ampere （V-I） measurement method has been applied ...Current dependence and stability of the measured resistance value are very important for the accurate measurement of DC standard resistor. In this paper, the volt-ampere （V-I） measurement method has been applied to study the current depend-ence of four different types of standard resistors. Diverse values are obtained through the investigation of their stability at dif-ferent currents. Therefore, the current dependence coefficient （CDC） can be determined for each one of the studied resistors. Research shows CDC depends on the applied current value, the measurement time and the resistor type, as clearly demonstra-ted in this research.展开更多
The Virtual Resistor based Active Damping(VR-AD) is widely employed in converters connected to the grid via LCL filters in order to mitigate the inherent resonance of the filters. Nevertheless, in digitally controlled...The Virtual Resistor based Active Damping(VR-AD) is widely employed in converters connected to the grid via LCL filters in order to mitigate the inherent resonance of the filters. Nevertheless, in digitally controlled systems, the PWM and the calculating delays modify the system characteristics in terms of frequency and phase, thus destabilizing the system and degrading the VR-AD performances, mainly in low switching frequencies. Moreover, the stability of the system is greatly affected under weak grid operation characterized by large grid impedance variation. This paper solves these problems by proposing a systematic, robust and optimized design procedure of voltage oriented PI control(VOC) with VRAD. The considered design procedure ensures robust control(sufficient stability margins) and high quality of grid current(reduced steady-state error and minimized THD value) despite the negative impact of digital time delay, grid impedance variation and filter parameters change. Simulation and experimental results are presented to show robustness and efficiency of the suggested design procedure.展开更多
To solve the chattering problem caused by discontinuous switching function in traditional sliding mode observer,a piecewise square root switching function with continuously varying characteristics is designed,and its ...To solve the chattering problem caused by discontinuous switching function in traditional sliding mode observer,a piecewise square root switching function with continuously varying characteristics is designed,and its stability is analyzed by using Lyapunov stability criterion.Secondly,according to the relationship among bus current,switching state and phase current,a single bus resistance sampling current reconstruction scheme without current sensors is adopted,which effectively reduces the cost of motor system.Finally,the feasibility and effectiveness of the proposed scheme are verified by simulation.展开更多
In order to utilize integrated passive technology in printed circuit boards （PCBs）, manufacturing processing for integrated resistors by lamination method was investigated. Integrated resistors fabricated from Ohmeg...In order to utilize integrated passive technology in printed circuit boards （PCBs）, manufacturing processing for integrated resistors by lamination method was investigated. Integrated resistors fabricated from Ohmega technologies in the experiment were 1 408 pieces per panel with four different patterns A, B, C and D and four resistance values of 25, 50, 75 and 100 fL Six panel per batch and four batches were performed totally. The testing was done for 960 pieces of integrated resistors randomly selected with the same size. The value distribution ranges and the relative standard deviation （RSD） show that the scatter degree of the resistance decreases with the resistor size increasing and/or with the resistance increasing. Patterns D with resistance of 75 and 100% for four patterns have the resistance value variances less than 10%. Patterns C and D with resistance of 100 Ω have the manufacturing tolerance less than 10%. The process capabilities are from about 0.6 to 1.6 for the designed testing patterns, which shows that the integrated resistors fabricated have the potential to be used in multilayer PCBs in the future.展开更多
Phenolic resin(PF) and nano-SiO2 were used to improve the curing property and high humidity resistance of epoxy resin (EP) and methyl nadic anhydride (MNA) resistor paint, respectively. Hydrogen bonds, formed between ...Phenolic resin(PF) and nano-SiO2 were used to improve the curing property and high humidity resistance of epoxy resin (EP) and methyl nadic anhydride (MNA) resistor paint, respectively. Hydrogen bonds, formed between phenolic resin and nano-SiO2 in alcohol, made nano-SiO2 disperse easily in EP/MNA paint through phenolic resin without being treated by supersonic vibration. When the mass ratio of PF to EP in paint is 3:7, the formed composite paint film can be cured in 2 min at 170 ℃ . When the mass ratio of nano-SiO2 to PF in paint is 3:100, the property of high humidity resistance of the composite paint is the best, meeting the requirement of varying ratio of resistance less than 0.1% after experiment on high humidity resistance. SEM analysis shows the surface of the composite paint film is smooth, glassy, tight and homogeneous, without acicular air holes.展开更多
The preparation of lead-free thick-film resistors are reported:using RuO 2 and ruthenates as conductive particles,glass powders composed of B 2 O 3,SiO 2,CaO and Al2 O 3 as insulating phase,adding organic matter which...The preparation of lead-free thick-film resistors are reported:using RuO 2 and ruthenates as conductive particles,glass powders composed of B 2 O 3,SiO 2,CaO and Al2 O 3 as insulating phase,adding organic matter which mainly consists of ethyl cellulose and terpineol to form printable pastes.Resistors were fabricated and sintered by conventional screen-printing on 96%Al 2 O 3 substrates,and then sintering in a belt furnace.X-ray diffraction(XRD) and electron scanning microscopy(SEM) have been used to characterize the conductive particles.The resistors exhibit good refiring stability and low temperature coefficient of resistance.Sheet resistance spans from about 80Ω/□ to 600Ω/□.The resistors prepared are qualified for common use.展开更多
In this paper we put forward a new concept about effective trapping center concentration N^e_T which is decreasing with the trapped charge Q corresponding to index movement,based on that,we discuss theⅠ-Ⅴand tempera...In this paper we put forward a new concept about effective trapping center concentration N^e_T which is decreasing with the trapped charge Q corresponding to index movement,based on that,we discuss theⅠ-Ⅴand temperature characteristics of polysilicon resistors.The new concept presents ideal theoretical interpretion for the originally observed current-voltage negative-resistance characteristics of polysilicon resistors formed on the flow sensor,and also for poly-silicon film resistors. The final results agree well with the theoretical current-voltage characteristics.展开更多
Purpose–This study aims to improve the availability of regenerative braking for urban metro vehicles by introducing a sensorless operational temperature estimation method for the braking resistor(BR)onboard the vehic...Purpose–This study aims to improve the availability of regenerative braking for urban metro vehicles by introducing a sensorless operational temperature estimation method for the braking resistor(BR)onboard the vehicle,which overcomes the vulnerability of having conventional temperature sensor.Design/methodology/approach–In this study,the energy model based sensorless estimation method is developed.By analyzing the structure and the convection dissipation process of the BR onboard the vehicle,the energy-based operational temperature model of the BR and its cooling domain is established.By adopting Newton’s law of cooling and the law of conservation of energy,the energy and temperature dynamic of the BR can be stated.To minimize the use of all kinds of sensors(including both thermal and electrical),a novel regenerative braking power calculation method is proposed,which involves only the voltage of DC traction network and the duty cycle of the chopping circuit;both of them are available for the traction control unit(TCU)of the vehicle.By utilizing a real-time iterative calculation and updating the parameter of the energy model,the operational temperature of the BR can be obtained and monitored in a sensorless manner.Findings–In this study,a sensorless estimation/monitoring method of the operational temperature of BR is proposed.The results show that it is possible to utilize the existing electrical sensors that is mandatory for the traction unit’s operation to estimate the operational temperature of BR,instead of adding dedicated thermal sensors.The results also validate the effectiveness of the proposal is acceptable for the engineering practical.Originality/value–The proposal of this study provides novel concepts for the sensorless operational temperature monitoring of BR onboard rolling stocks.The proposed method only involves quasi-global electrical variable and the internal control signal within the TCU.展开更多
The shear strength of two joints with different compositions (Sn63Pb37 and SnAg3.0Cu0.5) was compared under thermal cycling conditions, and the effects of thermal cycling times on the two different joints were studied...The shear strength of two joints with different compositions (Sn63Pb37 and SnAg3.0Cu0.5) was compared under thermal cycling conditions, and the effects of thermal cycling times on the two different joints were studied. Results indicate that the shear force of the joints soldered with lead-free solder is higher than that of the joints soldered with Sn-Pb solder. After 120 times thermal cycling, the shear force of both the two kinds of joints declines obviously. The fractures are located at the two interfaces which is between the resistor’s side pad and the ceramic, the other is between the resistor’s bottom pad and the solder. Analysis result on the fractures by means of SEM indicates that the micrographs of fractures change obviously and the grains grow coarser after thermal cycling.展开更多
We present a new fractional-order resistor-capacitor controller and a novel control method based on the fractional- order controller to control an arbitrary three-dimensional fractional chaotic system. The proposed co...We present a new fractional-order resistor-capacitor controller and a novel control method based on the fractional- order controller to control an arbitrary three-dimensional fractional chaotic system. The proposed control method is simple, robust, and theoretically rigorous, and its anti-noise performance is satisfactory. Numerical simulations are given for several fractional chaotic systems to verify the effectiveness and the universality of the proposed control method.展开更多
A subranging analog-to-digital converter (ADC) features high-speed and relatively low-power. The limiting factors of power reduction in subranging ADCs are the resistor ladder and the comparator. We propose an ADC arc...A subranging analog-to-digital converter (ADC) features high-speed and relatively low-power. The limiting factors of power reduction in subranging ADCs are the resistor ladder and the comparator. We propose an ADC architecture combining a capacitive digital-to-analog convertor and built-in threshold calibration to eliminate the resistor ladder, resulting in a low-power subranging ADC. We also propose a calibration technique comprising of metal-oxide-metal capacitor, MOS switch, and scaling capacitor to reduce the power consumption of the comparator and an offset drift compensation technique to enable precise foreground calibration. We designed an 8-bit, 1-GHz subranging ADC by applying these techniques, and post-layout simulation results demonstrated a power consumption of 7 mW and figure of merit of 51 fJ/conv.-step.展开更多
The results of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistor) are reported. The formation of diffusion zones in the softened glass during firing...The results of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistor) are reported. The formation of diffusion zones in the softened glass during firing process of the mixture of the glass and the dopant powders is considered. As the result the doping glass becomes conductive. These diffusion zones have higher conductivity and act as percolation levels for the free charge carriers. The effect of tem-perature and duration of firing process on the conductivity of doped glass is considered. Experimental results are in a good agreement with the model.展开更多
This paper presents a floating resistor employing CIDITA (current inverting differential input transconductance amplifier). The proposed floating resistor is based on CMOS technology of 0.18 μm. For the realization o...This paper presents a floating resistor employing CIDITA (current inverting differential input transconductance amplifier). The proposed floating resistor is based on CMOS technology of 0.18 μm. For the realization of this floating inductor, two CIDITA have been cascaded together, no other passive elements are used, giving advantage of reduced chip area and hence reduced losses. The given circuit topology has an advantage of realizing both positive and negative resistors. This paper presents a simple circuitry of floating resistor in which the value of resistance can be tuned by adjusting the gate voltage of MOSFET. The PSpice simulation result shows constant resistance of 1.6 K<span style="white-space:nowrap;">Ω for frequency bandwidth of 1 Hz to 1 MHz, with supply voltage of ±1.25 volts.展开更多
This article is the final part of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistors). In the first part [1], the formation of percolation levels du...This article is the final part of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistors). In the first part [1], the formation of percolation levels due to diffusion of dopant atoms into the glass has been considered. The diffusion mechanism allowed us to explain shifting of the percolation threshold towards to lower value and the effect of firing conditions as well as the components composition on the electrical conduction of the doped glass. The coexistence of thermal activation and localization of free charge carriers as the result of nanocrystalline structure of the glass was the subject of the second part [2]. Because of it, the resistivity of the doped silicate glass is proportional to exp (–aT–ζ) at low temperatures (T 50 K), 0.4 ζ < 0.8. Structural transitions of nanocrystals take place at high temperatures (T > 800 K) and the conductivity of the doped silicate glass decreases sharply. We consider the origin of the minimum in the temperature dependence of resistivity of the doped silicate glass here. It is shown that the minimum arises from merge of impurity band into the valence band of glass at temperature high enough, so thermal activation of charge carriers as well as its hopping are failed, and scattering of free charge carriers become predominant factor in the temperature dependence of the resistivity.展开更多
文摘We consider a profound problem of two-point resistance in the resistor network with a null resistor edge and an arbitrary boundary,which has not been solved before because the Green＇s function technique and the Laplacian matrix approach are invalid in this case.Looking for the exact solutions of resistance is important but difficult in the case of the arbitrary boundary since the boundary is a wall or trap which affects the behavior of a finite network.In this paper,we give a general resistance formula that is composed of a single summation by using the recursion-transform method.Meanwhile,several interesting results are derived by the general formula.Further,the current distribution is given explicitly as a byproduct of the method.
基金Project supported by the National Natural Science Foundation of China(Grant No.51207060)the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No.20090142110004)
文摘A wideband metamaterial absorber （MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loaded with lumped resistors, a dielectric substrate, and a metal plate. We simulated, fabricated, measured, and analyzed the MA. The experimental results show that the reflectance （S11） is below -10 dB at normal incidence in the frequency range of 7.7 GHz 18 GHz, and the peak value is about -20 dB. Simulated power loss density distributions indicate that wideband absorption of the MA is mainly attributable to the lumped resistors in the magnetic resonator. Further investigations indicate that the distance between two unit cells along the magnetic field direction significantly influences the performance of the MA.
基金Supported by the National Natural Science Foundation of China(No.61201038)
文摘Phenolic formaldehyde(PF)and epoxy(EP)resins are commonly used in electronic packaging. In this paper, high-ohmic resistors(2.2 M?, ±0.5%,)with Cr-Si film were coated by PF/EP paint, and the resulting coated resistors were used for heat and humid(HH)experiments. The experimental results show that the corrosion of bandlike resistive films is selective and isotropic, and that the corrosion spots in resistive films all form along grooves and extend in the same direction. It is revealed that OH^- ions are generated due to the electrochemical reactions of resistive film in HH experiments, so a NaOH aqueous solution with pH about 10 was used to study the effects of absorbed water and OH^- ions on PF/EP polymer film. The results indicates that the color of some part on PF/EP polymer film changes due to corrosion, and that the corrosion part of the polymer film is easy to be peeled off. It can be inferred that OH^- ions generated in HH experiments may play a catalytic role in the chemical reactions between polymer film and the absorbed water, which accelerates the degradation of PF/EP protection film for a resistor.
基金supported by a grant from the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy, Republic of Koreasupported by Basic Science Research program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2010-0001-226)
文摘IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·cm by the IrO2 intermixing ratio from 0.55 to 0.78 in the IrO2-TiO2 thin films. The low temperature coefficient of resistance（TCR） values can be obtained by adopting IrO2-TiO2 composite thin films. Moreover, the change in the resistivity of IrO2-TiO2 thin films was below 10% even after O2 annealing process at 600 ℃. The step stress test results show that IrO2-TiO2 films have better characteristics than conventional TaN08 heater resistor. Therefore, IrO2-TiO2 composite thin films can be used as a heater resistor material in thermal inkjet printhead.
基金Supported by Science and Technology Committee of Tianjin (No.06YFGPGX08400)Ministry of Science and Technology of China (No.2009GJF20022)Innovation Fund of Tianjin University
文摘High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than ±15×10-6/℃.Cr-Si-Ta-Al films were prepared with Ar flow rate and sputtering power fixed at 20 standard-state cubic centimeter per minute(sccm) and 100 W,respectively.The experiment shows that the electrical properties of Cr-SiTa-Al deposition films can meet the specification requirements of 0603 ty...
文摘Results of investigation of X-ray diffraction, infrared and optical spectra of powders of the ruthenium dioxide, lead-silicate glass as well as their mixture before and after sintering are reported. Sintering conditions typical for thick film resistors were used. Intensity of main lines of RuO2 in X-ray diffraction patterns of sintered mixtures decreases and they slightly shift towards small angles. No new reflexes appear in these patterns. Absorbance of RuO2 in the range of 2.5-100 μm is proportional to and featureless. Infrared spectrum of lead-silicate glass has absorption bands of [SiO4]4- tetrahedra and Pb-O bonds only. Optical spectrum of RuO2 has wide absorption bands at 950 and 370 nm. Spectra of the mixture of RuO2 and glass powders before and after sintering are different indicating that there is interaction between them during the sintering process. Concentration of free charge carriers estimated from the optical spectra is about 1021 cm-3.
文摘Current dependence and stability of the measured resistance value are very important for the accurate measurement of DC standard resistor. In this paper, the volt-ampere （V-I） measurement method has been applied to study the current depend-ence of four different types of standard resistors. Diverse values are obtained through the investigation of their stability at dif-ferent currents. Therefore, the current dependence coefficient （CDC） can be determined for each one of the studied resistors. Research shows CDC depends on the applied current value, the measurement time and the resistor type, as clearly demonstra-ted in this research.
基金supported by the Tunisian Ministry of High Education and Research under Grant LSE-ENIT-LR11ES15
文摘The Virtual Resistor based Active Damping(VR-AD) is widely employed in converters connected to the grid via LCL filters in order to mitigate the inherent resonance of the filters. Nevertheless, in digitally controlled systems, the PWM and the calculating delays modify the system characteristics in terms of frequency and phase, thus destabilizing the system and degrading the VR-AD performances, mainly in low switching frequencies. Moreover, the stability of the system is greatly affected under weak grid operation characterized by large grid impedance variation. This paper solves these problems by proposing a systematic, robust and optimized design procedure of voltage oriented PI control(VOC) with VRAD. The considered design procedure ensures robust control(sufficient stability margins) and high quality of grid current(reduced steady-state error and minimized THD value) despite the negative impact of digital time delay, grid impedance variation and filter parameters change. Simulation and experimental results are presented to show robustness and efficiency of the suggested design procedure.
文摘To solve the chattering problem caused by discontinuous switching function in traditional sliding mode observer,a piecewise square root switching function with continuously varying characteristics is designed,and its stability is analyzed by using Lyapunov stability criterion.Secondly,according to the relationship among bus current,switching state and phase current,a single bus resistance sampling current reconstruction scheme without current sensors is adopted,which effectively reduces the cost of motor system.Finally,the feasibility and effectiveness of the proposed scheme are verified by simulation.
基金Project(041010) supported by Start-Up Foundation of Northwest University,ChinaProject(UIT/39) supported by University-Industry Collaboration Program from the Innovation and Technology Fund of Hong Kong,China
文摘In order to utilize integrated passive technology in printed circuit boards （PCBs）, manufacturing processing for integrated resistors by lamination method was investigated. Integrated resistors fabricated from Ohmega technologies in the experiment were 1 408 pieces per panel with four different patterns A, B, C and D and four resistance values of 25, 50, 75 and 100 fL Six panel per batch and four batches were performed totally. The testing was done for 960 pieces of integrated resistors randomly selected with the same size. The value distribution ranges and the relative standard deviation （RSD） show that the scatter degree of the resistance decreases with the resistor size increasing and/or with the resistance increasing. Patterns D with resistance of 75 and 100% for four patterns have the resistance value variances less than 10%. Patterns C and D with resistance of 100 Ω have the manufacturing tolerance less than 10%. The process capabilities are from about 0.6 to 1.6 for the designed testing patterns, which shows that the integrated resistors fabricated have the potential to be used in multilayer PCBs in the future.
基金Supported by Science and Technology Committee of Tianjin(No06YFGPGX08400)
文摘Phenolic resin(PF) and nano-SiO2 were used to improve the curing property and high humidity resistance of epoxy resin (EP) and methyl nadic anhydride (MNA) resistor paint, respectively. Hydrogen bonds, formed between phenolic resin and nano-SiO2 in alcohol, made nano-SiO2 disperse easily in EP/MNA paint through phenolic resin without being treated by supersonic vibration. When the mass ratio of PF to EP in paint is 3:7, the formed composite paint film can be cured in 2 min at 170 ℃ . When the mass ratio of nano-SiO2 to PF in paint is 3:100, the property of high humidity resistance of the composite paint is the best, meeting the requirement of varying ratio of resistance less than 0.1% after experiment on high humidity resistance. SEM analysis shows the surface of the composite paint film is smooth, glassy, tight and homogeneous, without acicular air holes.
文摘The preparation of lead-free thick-film resistors are reported:using RuO 2 and ruthenates as conductive particles,glass powders composed of B 2 O 3,SiO 2,CaO and Al2 O 3 as insulating phase,adding organic matter which mainly consists of ethyl cellulose and terpineol to form printable pastes.Resistors were fabricated and sintered by conventional screen-printing on 96%Al 2 O 3 substrates,and then sintering in a belt furnace.X-ray diffraction(XRD) and electron scanning microscopy(SEM) have been used to characterize the conductive particles.The resistors exhibit good refiring stability and low temperature coefficient of resistance.Sheet resistance spans from about 80Ω/□ to 600Ω/□.The resistors prepared are qualified for common use.
文摘In this paper we put forward a new concept about effective trapping center concentration N^e_T which is decreasing with the trapped charge Q corresponding to index movement,based on that,we discuss theⅠ-Ⅴand temperature characteristics of polysilicon resistors.The new concept presents ideal theoretical interpretion for the originally observed current-voltage negative-resistance characteristics of polysilicon resistors formed on the flow sensor,and also for poly-silicon film resistors. The final results agree well with the theoretical current-voltage characteristics.
基金supported by the Fund of China Academy of Railway Sciences Corporation Limited(2022YJ230)the Scientific Research Projects of China Association of Metros(CAMET-KY-2022039).
文摘Purpose–This study aims to improve the availability of regenerative braking for urban metro vehicles by introducing a sensorless operational temperature estimation method for the braking resistor(BR)onboard the vehicle,which overcomes the vulnerability of having conventional temperature sensor.Design/methodology/approach–In this study,the energy model based sensorless estimation method is developed.By analyzing the structure and the convection dissipation process of the BR onboard the vehicle,the energy-based operational temperature model of the BR and its cooling domain is established.By adopting Newton’s law of cooling and the law of conservation of energy,the energy and temperature dynamic of the BR can be stated.To minimize the use of all kinds of sensors(including both thermal and electrical),a novel regenerative braking power calculation method is proposed,which involves only the voltage of DC traction network and the duty cycle of the chopping circuit;both of them are available for the traction control unit(TCU)of the vehicle.By utilizing a real-time iterative calculation and updating the parameter of the energy model,the operational temperature of the BR can be obtained and monitored in a sensorless manner.Findings–In this study,a sensorless estimation/monitoring method of the operational temperature of BR is proposed.The results show that it is possible to utilize the existing electrical sensors that is mandatory for the traction unit’s operation to estimate the operational temperature of BR,instead of adding dedicated thermal sensors.The results also validate the effectiveness of the proposal is acceptable for the engineering practical.Originality/value–The proposal of this study provides novel concepts for the sensorless operational temperature monitoring of BR onboard rolling stocks.The proposed method only involves quasi-global electrical variable and the internal control signal within the TCU.
文摘The shear strength of two joints with different compositions (Sn63Pb37 and SnAg3.0Cu0.5) was compared under thermal cycling conditions, and the effects of thermal cycling times on the two different joints were studied. Results indicate that the shear force of the joints soldered with lead-free solder is higher than that of the joints soldered with Sn-Pb solder. After 120 times thermal cycling, the shear force of both the two kinds of joints declines obviously. The fractures are located at the two interfaces which is between the resistor’s side pad and the ceramic, the other is between the resistor’s bottom pad and the solder. Analysis result on the fractures by means of SEM indicates that the micrographs of fractures change obviously and the grains grow coarser after thermal cycling.
基金Project supported by the National Natural Science Foundation of China (Grant No. 11171238)the Ministry of Education Program for Changjiang Scholars and Innovative Research Team in University, China (Grant No. IRTO0742)
文摘We present a new fractional-order resistor-capacitor controller and a novel control method based on the fractional- order controller to control an arbitrary three-dimensional fractional chaotic system. The proposed control method is simple, robust, and theoretically rigorous, and its anti-noise performance is satisfactory. Numerical simulations are given for several fractional chaotic systems to verify the effectiveness and the universality of the proposed control method.
文摘A subranging analog-to-digital converter (ADC) features high-speed and relatively low-power. The limiting factors of power reduction in subranging ADCs are the resistor ladder and the comparator. We propose an ADC architecture combining a capacitive digital-to-analog convertor and built-in threshold calibration to eliminate the resistor ladder, resulting in a low-power subranging ADC. We also propose a calibration technique comprising of metal-oxide-metal capacitor, MOS switch, and scaling capacitor to reduce the power consumption of the comparator and an offset drift compensation technique to enable precise foreground calibration. We designed an 8-bit, 1-GHz subranging ADC by applying these techniques, and post-layout simulation results demonstrated a power consumption of 7 mW and figure of merit of 51 fJ/conv.-step.
文摘The results of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistor) are reported. The formation of diffusion zones in the softened glass during firing process of the mixture of the glass and the dopant powders is considered. As the result the doping glass becomes conductive. These diffusion zones have higher conductivity and act as percolation levels for the free charge carriers. The effect of tem-perature and duration of firing process on the conductivity of doped glass is considered. Experimental results are in a good agreement with the model.
文摘This paper presents a floating resistor employing CIDITA (current inverting differential input transconductance amplifier). The proposed floating resistor is based on CMOS technology of 0.18 μm. For the realization of this floating inductor, two CIDITA have been cascaded together, no other passive elements are used, giving advantage of reduced chip area and hence reduced losses. The given circuit topology has an advantage of realizing both positive and negative resistors. This paper presents a simple circuitry of floating resistor in which the value of resistance can be tuned by adjusting the gate voltage of MOSFET. The PSpice simulation result shows constant resistance of 1.6 K<span style="white-space:nowrap;">Ω for frequency bandwidth of 1 Hz to 1 MHz, with supply voltage of ±1.25 volts.
文摘This article is the final part of the investigation of conduction mechanism of silicate glass doped by oxide compounds of ruthenium (thick film resistors). In the first part [1], the formation of percolation levels due to diffusion of dopant atoms into the glass has been considered. The diffusion mechanism allowed us to explain shifting of the percolation threshold towards to lower value and the effect of firing conditions as well as the components composition on the electrical conduction of the doped glass. The coexistence of thermal activation and localization of free charge carriers as the result of nanocrystalline structure of the glass was the subject of the second part [2]. Because of it, the resistivity of the doped silicate glass is proportional to exp (–aT–ζ) at low temperatures (T 50 K), 0.4 ζ < 0.8. Structural transitions of nanocrystals take place at high temperatures (T > 800 K) and the conductivity of the doped silicate glass decreases sharply. We consider the origin of the minimum in the temperature dependence of resistivity of the doped silicate glass here. It is shown that the minimum arises from merge of impurity band into the valence band of glass at temperature high enough, so thermal activation of charge carriers as well as its hopping are failed, and scattering of free charge carriers become predominant factor in the temperature dependence of the resistivity.
