The dependence of perpendicular magnetic anisotropy （PMA） on the barrier layer MgO thickness in MgO/CoFeB /Ta multilayers is investigated. The results show that the strongest PMA occurs in a small window of about 2 ...The dependence of perpendicular magnetic anisotropy （PMA） on the barrier layer MgO thickness in MgO/CoFeB /Ta multilayers is investigated. The results show that the strongest PMA occurs in a small window of about 2 4nm with the increase of MgO thickness from 1-1Onto. The crystalline degree of MgO and the change of interatomic distance along the out-of-plane direction may be the main reasons for the change of PMA in these multilayers. Moreover, the roughnesses of 2- and 4-nm-thick MgO samples are 3.163 and 1.8 nm, respectively, and both the samples show PMA. These results could be used to tune the magnetic characteristic of the ultra thin CoFeB film for future applications in perpendicular magnetic devices.展开更多
A model system consisting of Ni[001]（100）/Ni3Al[001]（100） multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation ...A model system consisting of Ni[001]（100）/Ni3Al[001]（100） multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation results are consistent with the experimental observation that rafted Ni-base superalloys virtually possess a cubic symmetry. The convergence of the elastic properties with respect to the thickness of the multilayers are tested by a series of multilayers from 2γ′＋2γto 10γ′＋10γ atomic layers. The elastic properties are found to vary little with the increase of the multilayer＇s thickness. A Ni/Ni3Al multilayer with 10γ′＋10γ atomic layers （3.54 nm） can be used to simulate the mechanical properties of Ni-base model superalloys. Our calculated elastic constants, bulk modulus, orientation-dependent shear modulus and Young＇s modulus, as well as the Zener anisotropy factor are all compatible with the measured results of Ni-base model superalloys R1 and the advanced commercial superalloys TMS-26, CMSX-4 at a low temperature. The mechanical properties as a function of the γ′ phase volume fraction are calculated by varying the proportion of the γ and γ′ phase in the multilayers. Besides, the mechanical properties of two-phase Ni/Ni3Al multilayer can be well predicted by the Voigt-Reuss-Hill rule of mixtures.展开更多
Enhancement of post-annealing stability in Co/ Ni multilayers with perpendicular magnetic anisotropy （PMA） was obtained by inserting Au layers into Ni/Co interfaces. After annealing at 350 ℃, the effective mag- net...Enhancement of post-annealing stability in Co/ Ni multilayers with perpendicular magnetic anisotropy （PMA） was obtained by inserting Au layers into Ni/Co interfaces. After annealing at 350 ℃, the effective mag- netic anisotropy density （Kef0 for Ta（3）/Pt（2）/[Co（0.3）/ Ni（0.6）/Au（0.3）]× 3/Co（0.3）/Pt（1）/Ta（3） （in nm） keeps at 0.48 × 105 J·m^-3. Scanning transmission electron micro- scopy-high-angle annular dark field （STEM-HAADF） analysis shows that the diffusion between Ni and Co layers is obstructed by the Au insertion layers among them, which is responsible for the post-annealing stability enhancement of the multilayers. Multilayers with Pt insertion layers were also investigated as reference samples in this work. Com- pared with Pt-layer-inserted Co/Ni multilayers, the Au insertion layers are found to bring seldom interfacial PMA to the multilayers, making it competitive in being employed to enhance the post-annealing stability of PMA Co/Ni multilayers which are used for magnetic random access memory devices （MRAM）.展开更多
GMR effect of multilayers of bcc-Fe(M)(M=Co, Ni) alloy and Cu layers has been investigated. The maximum MR ratio is found at 1.1 nm Fe(Co) and 1.3～1.4 nm Cu layer thickness in [Fe(Co)/CuJ, and at 1.6 nm Fe(Ni) and 1....GMR effect of multilayers of bcc-Fe(M)(M=Co, Ni) alloy and Cu layers has been investigated. The maximum MR ratio is found at 1.1 nm Fe(Co) and 1.3～1.4 nm Cu layer thickness in [Fe(Co)/CuJ, and at 1.6 nm Fe(Ni) and 1.4 nm Cu layer thickness in [Fe(Ni)/Cu]. Under the optimum annealing condition, the MR ratio increases up to 50% and 38% for Fe(Co) and Fe(Ni) systems, respectively. The origin of the increase of GMR is discussed, taking the progress of preferred orientation of Fe(Co)[100] or Fe(Ni)[100] by anneahng into account.展开更多
The magnetic properties of Ni/Cu multilayers, prepared by the electron beam evaporation method under ultra high vacuum conditions, have been systematically studied by magnetic measurements. The temperature dependence ...The magnetic properties of Ni/Cu multilayers, prepared by the electron beam evaporation method under ultra high vacuum conditions, have been systematically studied by magnetic measurements. The temperature dependence of the spontaneous magnetization M (T) is well described by a T3/2 law. A spin wave theory has been used to explain the magnetization versus temperature. Based on this theory, the approximate values for the exchange interactions have been obtained.展开更多
应用磁控溅射法在玻璃基片上制备了以Pt为底层的CoFeB/Ni多层膜结构样品,通过测试样品的反常霍尔效应研究多层膜的垂直磁各向异性(perpendicular magnetic anisotropy,PMA),对影响多层膜垂直磁各向异性的各因素进行了调制.实验结果表明...应用磁控溅射法在玻璃基片上制备了以Pt为底层的CoFeB/Ni多层膜结构样品,通过测试样品的反常霍尔效应研究多层膜的垂直磁各向异性(perpendicular magnetic anisotropy,PMA),对影响多层膜垂直磁各向异性的各因素进行了调制.实验结果表明,多层膜的底层厚度、周期层中各层的厚度及周期数对样品的反常霍尔效应和磁性有重要影响.通过对样品各参数的逐步调制,最终获得了具有良好PMA的CoFeB/Ni多层膜最佳样品Pt(4)/[CoFeB(0.4)/Ni(0.3)]_3/Pt(1.0).经测试计算,该样品的各向异性常数K_(eff)为2.2×10~6erg/cm^3(1 erg/cm^3=10^(-1)J/m^3),具有良好的PMA性能,样品总厚度为7.1 nm,完全满足制备垂直磁结构材料的厚度要求,可进一步研究其在器件中的集成与应用.展开更多
Nanomultilayered TiN/Ni thin films with different bilayer periods(57.8-99.7 nm) and Ni single-layer thickness(3.9-19.2 nm) were prepared by alternatively sputtering Ti and Ni targets in N2 gas atmosphere.The micros tr...Nanomultilayered TiN/Ni thin films with different bilayer periods(57.8-99.7 nm) and Ni single-layer thickness(3.9-19.2 nm) were prepared by alternatively sputtering Ti and Ni targets in N2 gas atmosphere.The micros tructure,mechanical and corrosion properties of the multilayer films were investigated by X-ray diffraction(XRD),field emission scanning electron microscopy(FESEM),X-ray photoelectron spectroscopy(XPS),nanoindenter and electrochemical technologies.The multilayer films are fine with a mean grain size of ~8-9 nm independent of the bilayer period.However,the smoothness and compactness seem to decrease with the bilayer period increasing.The hardness(H) and elastic modulus(E) of the multilayer films gradually decrease as the bilayer period increases,and the multilayer film with bilayer period of 57.8 nm exhibits higher H,ratios of(H/E^*and H^3/E^*2)(E^*is effective Young’s modulus)than the monolithic TiN film and the other multilayers.The multilayer films exhibit an obvious passivation phenomenon in 10% H2SO4 solution,and the passive current and corrosion current densities decrease,whereas the corrosion potential increases when the bilayer period or Ni single-layer thickness decreases.It is found that the passivating behavior and corrosion potential of the multilayers are more sensitive to Ni single-layer thickness than the bilayer period.More corrosion pits and lamellar flaking could be found on the films with larger bilayer period or Ni single-layer thickness.展开更多
Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited on to a steel substrate by the successive deposition of zinc and Zn-Ni alloy sublayers from dual baths. The coated sampl...Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited on to a steel substrate by the successive deposition of zinc and Zn-Ni alloy sublayers from dual baths. The coated samples were evaluated in terms of the surface appearance, surface and cross-sectional morphologies, as well as corrosion resistance. The microstructural characteristics that were examined using the field emission gun scanning electron microscopy （FEGSEM） confirmed the layered structure, grain refinement of the zinc and Zn-Ni alloy CMM coatings, and revealed the existence of microcracks caused by the internal stress in the thick Zn-Ni alloy sublayers. The corrosion resistance that was evaluated by means of the salt spray test shows that the zinc and Zn-Ni alloy CMM coatings were more corrosion-resistant than the monolithic coatings of zinc or Zn-Ni alloy of the same thickness. The possible reasons for the better protective performance of Zn-Ni/Zn CMM coatings were given on the basis of the analysis on the micrographic features of zinc and Zn-Ni alloy CMM eoatings after the corrosion test. A probable corrosion mechanism of zinc and Zn-Ni alloy CMM coatings was also proposed.展开更多
Al/Ni multilayer composites are produced by accumulative roll bonding process and then annealed with different temperatures and time.Macroscopic images,microstructure and mechanical properties of Al/Ni multilayer comp...Al/Ni multilayer composites are produced by accumulative roll bonding process and then annealed with different temperatures and time.Macroscopic images,microstructure and mechanical properties of Al/Ni multilayer composites are investigated.As for the macroscopic images,although there was an edge crack along the rolling direction at the third pass,the defect of composites was not serious and the forming quality of composites was relatively good.The yield strength and elongation of Al/Ni multilayer composites are improved after the annealing treatment;however,with the increase in annealing temperature and time,the yield strength and ciongation of Al/Ni multilayer composites are decreased.During the process of annealing treatment,aluminum atoms diffuse in the way of vacancy diffusion,which results in the formation of Al3Ni intermetallic phase at Al/Ni interface and Kirkendall void in the aluminum side.The content of Al3Ni intermetallic phase and Kirkenckill void would increase with the increase in annealing temperature and time.展开更多
A series of multilayers of Co36Fe46B18/SiO2 were fabricated by DC/RF magnetron sputtering,and further post-annealed in vacuum magnetic field at 200℃ for 2 h. The results show that the microstructures and electromagne...A series of multilayers of Co36Fe46B18/SiO2 were fabricated by DC/RF magnetron sputtering,and further post-annealed in vacuum magnetic field at 200℃ for 2 h. The results show that the microstructures and electromagnetic properties of Co36Fe46B18/SiO2 multilayer films can be altered by varying the thickness of CoFeB and the process of annealing. High permeability along with high magnetic loss in the GHz frequency range is achieved in the optimized discontinuous multilayer films. Both real and imaginary parts of the complex permeability are larger than 260 at 1.6 GHz for this film,and the resistivity is as high as 1.4 mΩ·cm. The discontinuous Co36Fe46B18/SiO2 multilayers are supposed to serve as the microwave absorbers and EMI shielding materials in GHz range.展开更多
Al/Ni reactive multilayer foil(RMF)possesses excellent comprehensive properties as a promising substitute for traditional Cu bridge.A theoretical resistivity model of Al/Ni RMF was developed to guide the optimization ...Al/Ni reactive multilayer foil(RMF)possesses excellent comprehensive properties as a promising substitute for traditional Cu bridge.A theoretical resistivity model of Al/Ni RMF was developed to guide the optimization of EFIs.Al/Ni RMF with different bilayer thicknesses and bridge dimensions were prepared by MEMS technology and electrical explosion tests were carried out.According to physical and chemical reactions in bridge,the electrical explosion process was divided into 5 stages:heating of condensed bridge,vaporization and diffusion of Al layers,intermetallic combination reaction,intrinsic explosion,ionization of metal gases,which are obviously shown in measured voltage curve.Effects of interface and grain boundary scattering on the resistivity of film metal were considered.Focusing on variations of substance and state,the resistivity was developed as a function of temperature at each stage.Electrical explosion curves were calculated by this model at different bilayer thicknesses,bridge dimensions and capacitor voltages,which showed an excellent agreement with experimental ones.展开更多
Novel properties and applications of multilayered nanowires(MNWs)urge researchers to understand their mechanical behaviors comprehensively.Using the molecular dynamic simulation,tensile behaviors of Ti/Ni MNWs are inv...Novel properties and applications of multilayered nanowires(MNWs)urge researchers to understand their mechanical behaviors comprehensively.Using the molecular dynamic simulation,tensile behaviors of Ti/Ni MNWs are investigated under a series of layer thickness values(1.31,2.34,and 7.17 nm)and strain rates(1.0×10^(8)s^(-1)≤ε≤5.0×10^(10)s^(-1)).The results demonstrate that deformation mechanisms of isopachous Ti/Ni MNWs are determined by the layer thickness and strain rate.Four distinct strain rate regions in the tensile process can be discovered,which are small,intermediate,critical,and large strain rate regions.As the strain rate increases,the initial plastic behaviors transform from interface shear(the shortest sample)and grain reorientation(the longest sample)in small strain rate region to amorphization of crystalline structures(all samples)in large strain rate region.Microstructure evolutions reveal that the disparate tensile behaviors are ascribed to the atomic fractions of different structures in small strain rate region,and only related to collapse of crystalline atoms in high strain rate region.A layer thickness-strain rate-dependent mechanism diagram is given to illustrate the couple effect on the plastic deformation mechanisms of the isopachous nanowires.The results also indicate that the modulation ratio significantly affects the tensile properties of unequal Ti/Ni MNWs,but barely affect the plastic deformation mechanisms of the materials.The observations from this work will promote theoretical researches and practical applications of Ti/Ni MNWs.展开更多
Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited from dual baths. The coated samples were evaluated in terms of surface appearance, surface and cross-sectional morpholog...Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited from dual baths. The coated samples were evaluated in terms of surface appearance, surface and cross-sectional morphologies, as well as corrosion resistance. The results obtained from the salt spray test show that the zinc and Zn-Ni alloy CMM coatings are more corrosion-resistant than the monolithic coatings of zinc or Zn-Ni alloy alone with a similar thickness. The corrosion potential measurement and anodic polarisation tests were undertaken to examine the probable corrosion mechanisms of zinc and Zn-Ni alloy CMM coatings. Analysis on the micrographic features of zinc and Zn-Ni alloy CMM coatings after the corrosion test explains the probable reasons why the Zn-Ni/Zn CMM coatings have a better protective performance. Surface morphologies and compositional analysis of the remaining coating material of Zn-Ni alloy deposit after the corrosion test confirms the dezincification mechanism of the Zn-Ni alloy deposit during the corrosion process.展开更多
Carbon/carbon composites modified by NiAl alloy were prepared using vacuum reactive melt infiltration methods with NiAl and titanium mixed powders as raw materials. The microstructures were investigated by scanning el...Carbon/carbon composites modified by NiAl alloy were prepared using vacuum reactive melt infiltration methods with NiAl and titanium mixed powders as raw materials. The microstructures were investigated by scanning electron microscopy. The fracture behavior, infiltration and oxidation mechanism were further discussed. The results indicated that NiAl alloy exhibited good wettability on the C/C preform because a TiC reaction layer formed at the interface. Multi-layer（PyC/TiC/NiAl＋TiC） coating evenly and compactly distributed on the surface of the carbon fiber in tubular form. The penetration depth of molten NiAl alloys depended on the reaction between the PyC and titanium. The impact fracture was inclined to along the interface between the NiAl permeability layer and C/C matrix. Al_2TiO_5 and TiO_2 formed on the surface, while the interior multi-layer tubular structure partially remained after oxidation at 1773 K for 30 min.展开更多
基金Supported by the National Basic Research Program of China under Grant No 2011CB921804the Beijing Key Subject Foundation of Condensed Matter Physics under Grant No 0114023
文摘The dependence of perpendicular magnetic anisotropy （PMA） on the barrier layer MgO thickness in MgO/CoFeB /Ta multilayers is investigated. The results show that the strongest PMA occurs in a small window of about 2 4nm with the increase of MgO thickness from 1-1Onto. The crystalline degree of MgO and the change of interatomic distance along the out-of-plane direction may be the main reasons for the change of PMA in these multilayers. Moreover, the roughnesses of 2- and 4-nm-thick MgO samples are 3.163 and 1.8 nm, respectively, and both the samples show PMA. These results could be used to tune the magnetic characteristic of the ultra thin CoFeB film for future applications in perpendicular magnetic devices.
基金Project supported by the State Key Development Program for Basic Research of China (Grant No 2006CB605102)
文摘A model system consisting of Ni[001]（100）/Ni3Al[001]（100） multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation results are consistent with the experimental observation that rafted Ni-base superalloys virtually possess a cubic symmetry. The convergence of the elastic properties with respect to the thickness of the multilayers are tested by a series of multilayers from 2γ′＋2γto 10γ′＋10γ atomic layers. The elastic properties are found to vary little with the increase of the multilayer＇s thickness. A Ni/Ni3Al multilayer with 10γ′＋10γ atomic layers （3.54 nm） can be used to simulate the mechanical properties of Ni-base model superalloys. Our calculated elastic constants, bulk modulus, orientation-dependent shear modulus and Young＇s modulus, as well as the Zener anisotropy factor are all compatible with the measured results of Ni-base model superalloys R1 and the advanced commercial superalloys TMS-26, CMSX-4 at a low temperature. The mechanical properties as a function of the γ′ phase volume fraction are calculated by varying the proportion of the γ and γ′ phase in the multilayers. Besides, the mechanical properties of two-phase Ni/Ni3Al multilayer can be well predicted by the Voigt-Reuss-Hill rule of mixtures.
基金financially supported by the National Natural Science Foundation of China(Nos.51101012, 51271211,51331002,51371025,51371027,51471028 and 51571017)the National Key Scientific Research Projects of China(No. 2015CB921502)+1 种基金the Beijing Nova Program(No.Z141103001814039)the Fundamental Research Funds for the Central Universities(No. FRF-TP-14-002C1)
文摘Enhancement of post-annealing stability in Co/ Ni multilayers with perpendicular magnetic anisotropy （PMA） was obtained by inserting Au layers into Ni/Co interfaces. After annealing at 350 ℃, the effective mag- netic anisotropy density （Kef0 for Ta（3）/Pt（2）/[Co（0.3）/ Ni（0.6）/Au（0.3）]× 3/Co（0.3）/Pt（1）/Ta（3） （in nm） keeps at 0.48 × 105 J·m^-3. Scanning transmission electron micro- scopy-high-angle annular dark field （STEM-HAADF） analysis shows that the diffusion between Ni and Co layers is obstructed by the Au insertion layers among them, which is responsible for the post-annealing stability enhancement of the multilayers. Multilayers with Pt insertion layers were also investigated as reference samples in this work. Com- pared with Pt-layer-inserted Co/Ni multilayers, the Au insertion layers are found to bring seldom interfacial PMA to the multilayers, making it competitive in being employed to enhance the post-annealing stability of PMA Co/Ni multilayers which are used for magnetic random access memory devices （MRAM）.
基金Ministry of Education, Science, Sports and Culture under Grantin-Aid for Scielltific Research on Priority Areas (A), Japan!(No.
文摘GMR effect of multilayers of bcc-Fe(M)(M=Co, Ni) alloy and Cu layers has been investigated. The maximum MR ratio is found at 1.1 nm Fe(Co) and 1.3～1.4 nm Cu layer thickness in [Fe(Co)/CuJ, and at 1.6 nm Fe(Ni) and 1.4 nm Cu layer thickness in [Fe(Ni)/Cu]. Under the optimum annealing condition, the MR ratio increases up to 50% and 38% for Fe(Co) and Fe(Ni) systems, respectively. The origin of the increase of GMR is discussed, taking the progress of preferred orientation of Fe(Co)[100] or Fe(Ni)[100] by anneahng into account.
文摘The magnetic properties of Ni/Cu multilayers, prepared by the electron beam evaporation method under ultra high vacuum conditions, have been systematically studied by magnetic measurements. The temperature dependence of the spontaneous magnetization M (T) is well described by a T3/2 law. A spin wave theory has been used to explain the magnetization versus temperature. Based on this theory, the approximate values for the exchange interactions have been obtained.
文摘应用磁控溅射法在玻璃基片上制备了以Pt为底层的CoFeB/Ni多层膜结构样品,通过测试样品的反常霍尔效应研究多层膜的垂直磁各向异性(perpendicular magnetic anisotropy,PMA),对影响多层膜垂直磁各向异性的各因素进行了调制.实验结果表明,多层膜的底层厚度、周期层中各层的厚度及周期数对样品的反常霍尔效应和磁性有重要影响.通过对样品各参数的逐步调制,最终获得了具有良好PMA的CoFeB/Ni多层膜最佳样品Pt(4)/[CoFeB(0.4)/Ni(0.3)]_3/Pt(1.0).经测试计算,该样品的各向异性常数K_(eff)为2.2×10~6erg/cm^3(1 erg/cm^3=10^(-1)J/m^3),具有良好的PMA性能,样品总厚度为7.1 nm,完全满足制备垂直磁结构材料的厚度要求,可进一步研究其在器件中的集成与应用.
基金financially supported by the National Natural Science Foundation of China (No.51171118)
文摘Nanomultilayered TiN/Ni thin films with different bilayer periods(57.8-99.7 nm) and Ni single-layer thickness(3.9-19.2 nm) were prepared by alternatively sputtering Ti and Ni targets in N2 gas atmosphere.The micros tructure,mechanical and corrosion properties of the multilayer films were investigated by X-ray diffraction(XRD),field emission scanning electron microscopy(FESEM),X-ray photoelectron spectroscopy(XPS),nanoindenter and electrochemical technologies.The multilayer films are fine with a mean grain size of ~8-9 nm independent of the bilayer period.However,the smoothness and compactness seem to decrease with the bilayer period increasing.The hardness(H) and elastic modulus(E) of the multilayer films gradually decrease as the bilayer period increases,and the multilayer film with bilayer period of 57.8 nm exhibits higher H,ratios of(H/E^*and H^3/E^*2)(E^*is effective Young’s modulus)than the monolithic TiN film and the other multilayers.The multilayer films exhibit an obvious passivation phenomenon in 10% H2SO4 solution,and the passive current and corrosion current densities decrease,whereas the corrosion potential increases when the bilayer period or Ni single-layer thickness decreases.It is found that the passivating behavior and corrosion potential of the multilayers are more sensitive to Ni single-layer thickness than the bilayer period.More corrosion pits and lamellar flaking could be found on the films with larger bilayer period or Ni single-layer thickness.
文摘Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited on to a steel substrate by the successive deposition of zinc and Zn-Ni alloy sublayers from dual baths. The coated samples were evaluated in terms of the surface appearance, surface and cross-sectional morphologies, as well as corrosion resistance. The microstructural characteristics that were examined using the field emission gun scanning electron microscopy （FEGSEM） confirmed the layered structure, grain refinement of the zinc and Zn-Ni alloy CMM coatings, and revealed the existence of microcracks caused by the internal stress in the thick Zn-Ni alloy sublayers. The corrosion resistance that was evaluated by means of the salt spray test shows that the zinc and Zn-Ni alloy CMM coatings were more corrosion-resistant than the monolithic coatings of zinc or Zn-Ni alloy of the same thickness. The possible reasons for the better protective performance of Zn-Ni/Zn CMM coatings were given on the basis of the analysis on the micrographic features of zinc and Zn-Ni alloy CMM eoatings after the corrosion test. A probable corrosion mechanism of zinc and Zn-Ni alloy CMM coatings was also proposed.
基金This research is sponsored by the National Natural Science Foundation of China(NSFC 51605307)the Scientific Research Foundation of the Education Department of Liaoning Province,China(LGD2016020).
文摘Al/Ni multilayer composites are produced by accumulative roll bonding process and then annealed with different temperatures and time.Macroscopic images,microstructure and mechanical properties of Al/Ni multilayer composites are investigated.As for the macroscopic images,although there was an edge crack along the rolling direction at the third pass,the defect of composites was not serious and the forming quality of composites was relatively good.The yield strength and elongation of Al/Ni multilayer composites are improved after the annealing treatment;however,with the increase in annealing temperature and time,the yield strength and ciongation of Al/Ni multilayer composites are decreased.During the process of annealing treatment,aluminum atoms diffuse in the way of vacancy diffusion,which results in the formation of Al3Ni intermetallic phase at Al/Ni interface and Kirkendall void in the aluminum side.The content of Al3Ni intermetallic phase and Kirkenckill void would increase with the increase in annealing temperature and time.
基金Project(50771047) supported by the National Natural Science Foundation of ChinaProject(NCET-04-0702) supported by the New Century Excellent Talents in University, ChinaProject(2005ABB002) supported by the Elitist in Natural Science Foundation of Hubei Province, China
文摘A series of multilayers of Co36Fe46B18/SiO2 were fabricated by DC/RF magnetron sputtering,and further post-annealed in vacuum magnetic field at 200℃ for 2 h. The results show that the microstructures and electromagnetic properties of Co36Fe46B18/SiO2 multilayer films can be altered by varying the thickness of CoFeB and the process of annealing. High permeability along with high magnetic loss in the GHz frequency range is achieved in the optimized discontinuous multilayer films. Both real and imaginary parts of the complex permeability are larger than 260 at 1.6 GHz for this film,and the resistivity is as high as 1.4 mΩ·cm. The discontinuous Co36Fe46B18/SiO2 multilayers are supposed to serve as the microwave absorbers and EMI shielding materials in GHz range.
基金National Natural Science Foundation of China(Grant No.11872013)for supporting this project.
文摘Al/Ni reactive multilayer foil(RMF)possesses excellent comprehensive properties as a promising substitute for traditional Cu bridge.A theoretical resistivity model of Al/Ni RMF was developed to guide the optimization of EFIs.Al/Ni RMF with different bilayer thicknesses and bridge dimensions were prepared by MEMS technology and electrical explosion tests were carried out.According to physical and chemical reactions in bridge,the electrical explosion process was divided into 5 stages:heating of condensed bridge,vaporization and diffusion of Al layers,intermetallic combination reaction,intrinsic explosion,ionization of metal gases,which are obviously shown in measured voltage curve.Effects of interface and grain boundary scattering on the resistivity of film metal were considered.Focusing on variations of substance and state,the resistivity was developed as a function of temperature at each stage.Electrical explosion curves were calculated by this model at different bilayer thicknesses,bridge dimensions and capacitor voltages,which showed an excellent agreement with experimental ones.
基金Project supported by the National Natural Science Foundation of China(Grant No.11572259)the Natural Science Foundation of Shaanxi Province,China(Grant No.2019JQ-827)the Scientific Research Program Funded by Shaanxi Provincial Education Department,China(Grant No.19JK0672).
文摘Novel properties and applications of multilayered nanowires(MNWs)urge researchers to understand their mechanical behaviors comprehensively.Using the molecular dynamic simulation,tensile behaviors of Ti/Ni MNWs are investigated under a series of layer thickness values(1.31,2.34,and 7.17 nm)and strain rates(1.0×10^(8)s^(-1)≤ε≤5.0×10^(10)s^(-1)).The results demonstrate that deformation mechanisms of isopachous Ti/Ni MNWs are determined by the layer thickness and strain rate.Four distinct strain rate regions in the tensile process can be discovered,which are small,intermediate,critical,and large strain rate regions.As the strain rate increases,the initial plastic behaviors transform from interface shear(the shortest sample)and grain reorientation(the longest sample)in small strain rate region to amorphization of crystalline structures(all samples)in large strain rate region.Microstructure evolutions reveal that the disparate tensile behaviors are ascribed to the atomic fractions of different structures in small strain rate region,and only related to collapse of crystalline atoms in high strain rate region.A layer thickness-strain rate-dependent mechanism diagram is given to illustrate the couple effect on the plastic deformation mechanisms of the isopachous nanowires.The results also indicate that the modulation ratio significantly affects the tensile properties of unequal Ti/Ni MNWs,but barely affect the plastic deformation mechanisms of the materials.The observations from this work will promote theoretical researches and practical applications of Ti/Ni MNWs.
文摘Zinc and Zn-Ni alloy compositionally modulated multilayer （CMM） coatings were electrodeposited from dual baths. The coated samples were evaluated in terms of surface appearance, surface and cross-sectional morphologies, as well as corrosion resistance. The results obtained from the salt spray test show that the zinc and Zn-Ni alloy CMM coatings are more corrosion-resistant than the monolithic coatings of zinc or Zn-Ni alloy alone with a similar thickness. The corrosion potential measurement and anodic polarisation tests were undertaken to examine the probable corrosion mechanisms of zinc and Zn-Ni alloy CMM coatings. Analysis on the micrographic features of zinc and Zn-Ni alloy CMM coatings after the corrosion test explains the probable reasons why the Zn-Ni/Zn CMM coatings have a better protective performance. Surface morphologies and compositional analysis of the remaining coating material of Zn-Ni alloy deposit after the corrosion test confirms the dezincification mechanism of the Zn-Ni alloy deposit during the corrosion process.
基金Project(2011CB605804) supported by the National Basic Research Development Program of ChinaProject(2015JJ3167) supported by the Natural Science Foundation of Hunan Province,ChinaProject(2013M531810) supported by the Postdoctoral Science Foundation of China
文摘Carbon/carbon composites modified by NiAl alloy were prepared using vacuum reactive melt infiltration methods with NiAl and titanium mixed powders as raw materials. The microstructures were investigated by scanning electron microscopy. The fracture behavior, infiltration and oxidation mechanism were further discussed. The results indicated that NiAl alloy exhibited good wettability on the C/C preform because a TiC reaction layer formed at the interface. Multi-layer（PyC/TiC/NiAl＋TiC） coating evenly and compactly distributed on the surface of the carbon fiber in tubular form. The penetration depth of molten NiAl alloys depended on the reaction between the PyC and titanium. The impact fracture was inclined to along the interface between the NiAl permeability layer and C/C matrix. Al_2TiO_5 and TiO_2 formed on the surface, while the interior multi-layer tubular structure partially remained after oxidation at 1773 K for 30 min.
基金Program of the Pearl River Young Talents of Science and Technology in Guangzhou(2013J2200033)the Project of Guangdong Provincial Key Laboratory(2012A061400011)the Guangdong Innovative Research Team Program(201101C0104901263)
