The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from...The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).展开更多
The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance You...The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance Young's modulus measurements,and microstructure analysis,the effects of dislocation density,vacancy formation,and recrystallization on the alloy performance were clarified.Results indicate that increasing the rolling reduction enhances damping property due to higher dislocation density,whereas aging below the recrystallization temperature reduces damping property via dislocation pinning by the Suzuki effect.Recrystallization heat treatment restores the original structure and damping level.This alloy possesses tensile strength of approximately 1500 MPa and logarithmic decrement valueδ^(-1) in the range of 2×10^(-4)–3×10^(-4),demonstrating superior mechanical properties compared with the Ti-based alloys,which makes it an excellent candidate material for ultrasonic tools and medical applications.展开更多
The multi-principal element characteristic of high-entropy alloys has revolutionized the conventional alloy design concept of single-principal element,endowing them with excellent mechanical properties.However,owing t...The multi-principal element characteristic of high-entropy alloys has revolutionized the conventional alloy design concept of single-principal element,endowing them with excellent mechanical properties.However,owing to this multi-principal element nature,high-entropy alloys exhibit complex deformation behavior dominated by alternating and coupled deformation mechanisms.Therefore,elucidating these intricate deformation mechanisms remains a key challenge in current research.Neutron diffraction(ND)techniques offer distinct advantages over traditional microscopic methods for characterizing such complex deformation behavior.The strong penetration capability of neutrons enables in-situ,real-time,and non-destructive detection of structural evolution in most centimeter-level bulk samples under complex environments,and ND allows precise characterization of lattice site occupations for light elements,such as C and O,and neighboring elements.This review discussed the principles of ND,experiment procedures,and data analysis.Combining with recent advances in the research about face-centered cubic high-entropy alloy,typical examples of using ND to investigate the deformation behavior were summarized,ultimately revealing deformation mechanisms dominated by dislocations,stacking faults,twinning,and phase transformations.展开更多
Quantitative assessment of microscale slip activities and plastic localizations is essential for understanding the complex deformation mechanisms in crystalline materials.However,few experimental studies have been abl...Quantitative assessment of microscale slip activities and plastic localizations is essential for understanding the complex deformation mechanisms in crystalline materials.However,few experimental studies have been able to dynamically measure the deformation fields of rapidly evolving slip activities at the microscale.In this study,we used the Sampling Moire?Method(SMM)to directly measure the dynamic deformation fields of slip activities in Nickel-Based Single-Crystal(NBSC)superalloy under in-situ tensile test,and the strain and displacement fields under the evolving microplastic events with intense slip activities around the notch of the NBSC superalloy specimen were obtained for the first time.The dynamic evolution of slip bands was quantitatively characterized through detailed statistical analysis of strains and displacements under different loads.The locations of the initial appearance of slip traces were successfully predicted by the regions of plasticity localization.The results show that the deformation fields exhibit both high spatial and temporal resolutions,enabling the capture of nanometer-scale displacement fields and visualization of the dynamic fluidity of slip accumulation.This method demonstrates the superiority of the dynamic characterization of the plastic deformation field at the microscale and the promise of its application for characterizing the slip activities of various crystalline metals.展开更多
A Hybrid Free-Form Deformation(HFFD)method is developed to improve shape preservation in mesh deformation for perforated surfaces,which traditional Free-Form Deformation(FFD)techniques struggle to handle effectively.T...A Hybrid Free-Form Deformation(HFFD)method is developed to improve shape preservation in mesh deformation for perforated surfaces,which traditional Free-Form Deformation(FFD)techniques struggle to handle effectively.The proposed method enables high-fidelity parameterized deformation for both flat and curved perforated surfaces while maintaining mesh quality with minimal geometric distortion.To evaluate its effectiveness,comparative studies between HFFD and conventional FFD methods are conducted,demonstrating superior performance in mesh quality and geometric fidelity.The HFFD-based framework is further applied to the Multidisciplinary Design Optimization(MDO)of a double-wall turbine blade leading edge.Results indicate an 11.6%increase in cooling efficiency and a 16.21%reduction in maximum stress.Additionally,compared to traditional geometry-based parameterization in MDO,the HFFD approach improves model processing efficiency by 84.15%and overall optimization efficiency by20.05%.These findings demonstrate HFFD's potential to significantly improve complex engineering design optimization by achieving precise shape preservation and improving computational efficiency.展开更多
The contact deformation and buckling of elastic rods against rigid surfaces represent a prevalent phenomenon in applications such as oil drilling,arterial stents,and energy harvesting.This has attracted widespread att...The contact deformation and buckling of elastic rods against rigid surfaces represent a prevalent phenomenon in applications such as oil drilling,arterial stents,and energy harvesting.This has attracted widespread attention from researchers.In this paper,the deformation and buckling behaviors of a circular arch subject to compression by a rigid plate are investigated with a planar elastic rod model that incorporates tension,shearing,and bending.In comparison with the existing models that solely consider the bending energy,the deflection curve,the internal force distribution,and the critical load of the present model show good agreement with the finite element results.Through the dimensional analysis and order-of-magnitude estimation,we examine the factors influencing the critical load.The study reveals that the semi-central angle of the arch has the most significant effect.The dimensionless geometric parameter describing arch slenderness becomes prominent when the semi-central angle is less than 30°,while Poisson's ratio and the cross-sectional shear correction factor exhibit negligible influence.Furthermore,the variation in the proportions of strain energy components during critical buckling is presented with respect to the semi-central angle and the geometric parameter,thereby delineating the applicable ranges of both the original model(OM)and the modified model(MM).展开更多
Central Sumatra,Indonesia,is historically known for its significant seismic activities,most notably the devastating 1883 earthquake.In this study,we measured the interseismic deformation using continuous GNSS observat...Central Sumatra,Indonesia,is historically known for its significant seismic activities,most notably the devastating 1883 earthquake.In this study,we measured the interseismic deformation using continuous GNSS observation data for three years from 2018 to 2021.5.The results show that the derived velocity fields indicate that the Central Sumatra deformation is primarily characterized by crustal strain shortening due to interaction between the India-Australian plate and the Sundaland plate.High strain values are observed along the Sumatran Fault Zone(SFZ),which is characterized by a history of significant seismic activity.Interseismic locking is divided into two segments.Segment A,located in the northern part of Siberut Island has an estimated moment magnitude of MW7.44 with a return period of200 years leading to a potential earthquake magnitude of MW8.98.Segment B in the southern part of Siberut Island has an estimated moment magnitude of MW7.26 with a return period of 200 years,resulting in a potential earthquake magnitude of MW8.79.The findings highlight critical seismic hazard implications,emphasizing the potential for a major earthquake in the Central Sumatra.展开更多
This study presents an implicit multiphysics coupling method integrating Computational Fluid Dynamics(CFD),the Multiphase Particle-in-Cell(MPPIC)model,and the Finite Element Method(FEM),implemented with OpenFOAM,Calcu...This study presents an implicit multiphysics coupling method integrating Computational Fluid Dynamics(CFD),the Multiphase Particle-in-Cell(MPPIC)model,and the Finite Element Method(FEM),implemented with OpenFOAM,CalculiX,and preCICE to simulate fluid-particle-structure interactions with large deformations.Mesh motion in the fluid field is handled using the radial basis function(RBF)method.The particle phase is modeled by MPPIC,where fluid-particle interaction is described through momentum exchange,and inter-particle collisions are characterized by collision stress.The structural field is solved by nonlinear FEM to capture large deformations induced by geometric nonlinearity.Coupling among fields is realized through a partitioned,parallel,and non-intrusive iterative strategy,ensuring stable transfer and convergence of interface forces and displacements.Notably,the influence of particles on the structure is not direct but mediated by the fluid,while structural motion directly affects particle dynamics.The results demonstrate that the proposed approach effectively captures multiphysics interaction processes and provides a valuable reference for numerical modeling of coupled fluid-particle-structure systems.展开更多
Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted dru...Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted drug delivery.For implants,mechanical properties are key performance characteristics,so understanding the deformation and failure mechanisms is essential for selecting the appropriate implant structure.The deformation and fracture processes in PLA samples with different interior architectures have been studied through computer simulation and experimental research.Two TPMS topologies,the Schwarz Diamond and Gyroid architectures,were used for the sample construction by 3D printing.ANSYS software was utilized to simulate compressive deformation.It was found that under the same load,the vonMises stresses in the Gyroid structure are higher than those in the Schwartz Diamond structure,which was associated with the different orientations of the cells in the studied structures in relation to the direction of the loading axis.The deformation process occurs in the local regions of the studied TPMS structures.Maximum von Mises stresses were observed in the vertical parts of the structures oriented along the load direction.It was found that,unlike the Gyroid,the Schwartz Diamond structure contains a frame that forms unique stiffening ribs,which ensures the redistribution of the load under the vertical loading direction.An analysis of the mechanical characteristics of PLA samples with the Schwartz Diamond and Gyroid structures produced by the Fused Deposition Modeling(FDM)method was correlated with computer simulation.The Schwarz Diamond-type structure was shown to have a higher absorption energy than the Gyroid one.A study of the fracture in PLA samples with various cell sizes revealed a particular feature related to the samples’periodic surface topology and the 3D printing process.Scanning electron microscopic(SEM)studies of the samples deformed by compression showed thatwith an increase in the density of the samples,the failure mechanism changes from ductile to quasi-brittle due to the complex participation of both cell deformation and fiber deformation.展开更多
High entropy alloy attracts widespread attention due to its excellent mechanical properties.It becomes a new type of alloy material with high application potential,but the grinding performance of High entropy alloy re...High entropy alloy attracts widespread attention due to its excellent mechanical properties.It becomes a new type of alloy material with high application potential,but the grinding performance of High entropy alloy receives little attention.This paper conducts grinding simulation and surface grinding experiments on FeCoCrNi high entropy and alloys to analyze the grinding removal mechanism of the FeCoCrNi-based High entropy alloy.We also discuss the influence of grinding parameters,element types,element content and forming methods on grinding force and sub-surface plastic deformation after grinding.The simulation and experimental results show that as the increase of grinding depth,both tangential grinding force and normal grinding force increase,and the thickness of sub-surface plastic deformation layer decreases.With the increase of grinding speed,both tangential grinding force and normal grinding force decrease,and the thickness of sub-surface plastic deformation layer caused by grinding process shows a trend of gradual decrease.Under the same processing parameters,the normal grinding force is greater than the tangential grinding force.In FeCoCrNi series high entropy alloys,the grinding force and subsurface plastic deformation layer thickness of high entropy alloys increased with the addition in Ti content.The grinding force and plastic deformation formed by adding Ti element are greater than those formed by adding Al element,and High entropy alloys prepared using laser cladding method exhibit greater grinding force and plastic deformation than those prepared using selective laser melting method.The research results provide theoretical reference and experimental basis for high-quality grinding of high entropy alloys,which may be helpful for the design and manufacturing of high entropy alloy parts.展开更多
Slopes are likely to fail in areas with frequent rainfall and earthquakes.The deformation characteristics of unsaturated slopes subjected to post-rainfall earthquakes are investigated using centrifuge model tests and ...Slopes are likely to fail in areas with frequent rainfall and earthquakes.The deformation characteristics of unsaturated slopes subjected to post-rainfall earthquakes are investigated using centrifuge model tests and finite element analyses.Three tests of the slope deformation under earthquake and post-rainfall earthquakes are first studied using image analysis techniques.Then,based on an elastoplastic constitutive model,numerical simulations are carried out using the finite element method and compared with the centrifuge test results.Finally,a parametric study is performed to clarify the effects of antecedent rainfall on earthquake-induced slope deformation.The results show that slope deformation caused by post-rainfall earthquakes differs from that caused by earthquakes without antecedent rainfall.The seepage flow and soil strength of the slope are affected by previous rainfall conditions,such as intensity and duration,which directly influence the slope deformation caused by the subsequent earthquake.Soil displacement and strain become greater and the slip surface is more noticeable during the post-rainfall earthquake of higher intensity.In addition,the time interval between the rainfall and the earthquake has a considerable impact on the detailed characteristics of the slope deformation,and the significant deformation occurs at the time of lowest soil strength when seepage flow reaches the lower part of the slope.Moreover,the repeated intermittent rainfall greatly affects the subsequent earthquake-induced slope deformation,the main characteristics of which are closely related to the changes in saturation and strength of the slope.However,with the prolonged time gap between each round of rainfall,the earthquake-induced slope deformation becomes insignificant.展开更多
A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relax...A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.展开更多
An MW6.0 earthquake struck Jishishan County in Linxia Prefecture,Gansu Province,on December 18,2023.In this research,Sentinel-1A satellite radar observations were used to obtain the field of coseismic deformation of t...An MW6.0 earthquake struck Jishishan County in Linxia Prefecture,Gansu Province,on December 18,2023.In this research,Sentinel-1A satellite radar observations were used to obtain the field of coseismic deformation of the Jishishan earthquake in 2023,and the geometric and fine slip distribution of the seismogenic fault were inverted using this as a constraint.The results show that the earthquake is characterized by thrust movement.The coseismic slip distribution results show that the maximum slip of this earthquake is 0.3 m.The Coulomb stress distribution shows that the whole section of the southern edge of Lajishan fault,the NWW trending segment of the northern edge of Lajishan fault and its NNW trending segment to the south of the epicenter,the northern edge of the West Qinling fault and the segment to the east of the epicenter of the Daotanghe Linxia fault are under stress loading,which indicates an increase in the potential risk of earthquakes.This research discussed the seismogenic characteristics of earthquakes and the tendency of faults.We speculate that the Jishishan earthquake is the result of the joint action of regional faults and tectonic stress.Based on the observation of seismic data,geodesy,and other geological and geophysical data,we believe that the earthquake was caused by the activation of weak areas under the crust by the local stress from the driving mechanism of the northeast expansion of Qinghai-Xizang Plateau.The seismogenic fault of this earthquake is more likely to be northeast dipping under the comprehensive consideration of various factors,which occurred on the concealed fault belonging to the eastern edge of the Jishishan fault zone.展开更多
Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under...Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under uniaxial tension along rolling direction(RD)and transverse direction(TD)at-50,25,50,and 150℃.Results reveal a transition from high strength with limited elongation at-50℃ to significant softening and maximum ductility at 150℃.TD samples consistently showed 2%-6%higher strength than RD;however,this yield anisotropy diminished at 150℃ due to the shift from twinning to thermally activated slip and recovery.Fractography indicated a change from semi-brittle to fully ductile fracture with increasing temperature.Electron backscattered diffraction(EBSD)analysis confirmed twinning-driven grain refinement at low temperatures,while deformation at high temperatures involved grain elongation along shear zones,enabling greater strain accommodation before material failure.展开更多
Ultra-high molecular weight polyethylene(UHMWPE)is a key material for marine applications owing to its outstanding self-lubrication and corrosion resistance.However,its long-term performance is compromised by plastic ...Ultra-high molecular weight polyethylene(UHMWPE)is a key material for marine applications owing to its outstanding self-lubrication and corrosion resistance.However,its long-term performance is compromised by plastic deformation in seawater.In this study,we performed a comparative analysis of the UHMWPE dynamics under seawater and water conditions to investigate the plastic deformation of UHMWPE induced by seawater.The results show that the plastic deformation of UHMWPE is amplified in seawater relative to the water conditions.Under thin fluid conditions,frictional interfaces exhibit a higher interfacial friction force and interaction energy in seawater than in water.Compared to freely diffused water molecules,hydrated ions occupy larger interchain spaces within polyethylene.Furthermore,the diffusion of hydrated ions weakens the interchain interactions,promoting more severe polyethylene chain rearrangement and accelerating seawater-induced plastic deformation in UHMWPE during friction.Furthermore,the diffused seawater accelerated the disentangling of the polyethylene chains and enhanced the orderly orientation distribution of polyethylene.Compared to free water molecules,the water molecules of hydrated ions exhibit enhanced attraction to free-flowing water molecules,thereby accelerating seawater flow across submerged UHMWPE surfaces.This flow enhancement promotes surface polyethylene chain mobility in seawater.展开更多
Ceramic 4D printing,which integrates dynamic deformation with additive manufacturing,demonstrates significant potential in intelligent manufacturing,on-demand shaping of complex structures,and multifunctional device d...Ceramic 4D printing,which integrates dynamic deformation with additive manufacturing,demonstrates significant potential in intelligent manufacturing,on-demand shaping of complex structures,and multifunctional device development.Its core advantage lies in endowing materials with environmentally responsive dynamic deformation capabilities.However,current technologies still face limitations in responsiveness,reversibility,and mechanical performance.To address these challenges,this study proposes a programmable ceramic precursor system based on synergistic reinforcement of phase-separating hydrogels and shape memory polymers,combined with a nano-ceramic particle enhancement strategy.Using stereolithography 3D printing,high-precision fabrication of complex structures was achieved.By adjusting precursor composition,programming time,and structural thickness,the phase-separation kinetics-driven delayed recovery mechanism was elucidated,enabling precise control over recovery onset time.Furthermore,the thermal response mechanism of the precursor materials is explored,along with their potential for multi-shape transformation in biomedical applications,which is further extended to shape memory polymer systems.By employing a layered printing strategy,the autonomous reversible deformation of ceramic precursors is realized,providing new possibilities for specific applications.展开更多
Deformation prediction for extra-high arch dams is highly important for ensuring their safe operation.To address the challenges of complex monitoring data,the uneven spatial distribution of deformation,and the constru...Deformation prediction for extra-high arch dams is highly important for ensuring their safe operation.To address the challenges of complex monitoring data,the uneven spatial distribution of deformation,and the construction and optimization of a prediction model for deformation prediction,a multipoint ultrahigh arch dam deformation prediction model,namely,the CEEMDAN-KPCA-GSWOA-KELM,which is based on a clustering partition,is pro-posed.First,the monitoring data are preprocessed via variational mode decomposition(VMD)and wavelet denoising(WT),which effectively filters out noise and improves the signal-to-noise ratio of the data,providing high-quality input data for subsequent prediction models.Second,scientific cluster partitioning is performed via the K-means++algorithm to precisely capture the spatial distribution characteristics of extra-high arch dams and ensure the consistency of deformation trends at measurement points within each partition.Finally,CEEMDAN is used to separate monitoring data,predict and analyze each component,combine the KPCA(Kernel Principal Component Analysis)and the KELM(Kernel Extreme Learning Machine)optimized by the GSWOA(Global Search Whale Optimization Algorithm),integrate the predictions of each component via reconstruction methods,and precisely predict the overall trend of ultrahigh arch dam deformation.An extra high arch dam project is taken as an example and validated via a comparative analysis of multiple models.The results show that the multipoint deformation prediction model in this paper can combine data from different measurement points,achieve a comprehensive,precise prediction of the deformation situation of extra high arch dams,and provide strong technical support for safe operation.展开更多
Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study el...Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
The high-order deformation effects in even-even^(246,248)No are investigated by means of pairing self-consistent WoodsSaxon-Strutinsky calculations using the potential-energy-surface(PES)approach in an extended deform...The high-order deformation effects in even-even^(246,248)No are investigated by means of pairing self-consistent WoodsSaxon-Strutinsky calculations using the potential-energy-surface(PES)approach in an extended deformation space(β_(2),β_(3),β_(4),β_(5),β_(6),β_(7),β_(8)).Based on the calculated two-dimensional projected energy maps and different potential energy curves,we found that the highly even-order deformations have an important impact on both the fission trajectory and energy minima,while the odd-order deformations,accompanying the even-order ones,primarily affect the fission path beyond the second barrier.Relative to the light actinide nuclei,the nuclear ground state changes to the superdeformed configuration,but the normally deformed minimum,as the low-energy shape isomer,may still be primarily responsible for enhancing nuclear stability and ensuring experimental accessibility in^(246,248)No.Our present investigation indicates the nonnegligible impact of high-order deformation effects along the fission valley and will be helpful for deepening the understanding of different deformation effects and deformation couplings in nuclei,especially in this neutron-deficient heavy-mass region.展开更多
基金Sichuan Science and Technology Program(2025ZNSFSC1341)Fundamental Research Funds for the Central Universities(J2022-090,25CAFUC04087)。
文摘The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).
文摘The strength and damping properties of Co-Ni-Cr-Mo-based alloys with 0.5wt%Nb addition after various plastic deformation and heat treatment processes were investigated.Through Vickers hardness tests,free resonance Young's modulus measurements,and microstructure analysis,the effects of dislocation density,vacancy formation,and recrystallization on the alloy performance were clarified.Results indicate that increasing the rolling reduction enhances damping property due to higher dislocation density,whereas aging below the recrystallization temperature reduces damping property via dislocation pinning by the Suzuki effect.Recrystallization heat treatment restores the original structure and damping level.This alloy possesses tensile strength of approximately 1500 MPa and logarithmic decrement valueδ^(-1) in the range of 2×10^(-4)–3×10^(-4),demonstrating superior mechanical properties compared with the Ti-based alloys,which makes it an excellent candidate material for ultrasonic tools and medical applications.
基金National Key R&D Program of China(2023YFB3711904,2022YFA1603801)National Natural Science Foundation of China(12404230,52471181,52301213,52130108,52471005)+2 种基金National Nature Science Foundation of Zhejiang Province(LY23E010002)Open Fund of the China Spallation Neutron Source,Songshan Lake Science City(KFKT2023B11)Guangdong Basic and Applied Basic Research Foundation(2022A1515110805,2024A1515010878)。
文摘The multi-principal element characteristic of high-entropy alloys has revolutionized the conventional alloy design concept of single-principal element,endowing them with excellent mechanical properties.However,owing to this multi-principal element nature,high-entropy alloys exhibit complex deformation behavior dominated by alternating and coupled deformation mechanisms.Therefore,elucidating these intricate deformation mechanisms remains a key challenge in current research.Neutron diffraction(ND)techniques offer distinct advantages over traditional microscopic methods for characterizing such complex deformation behavior.The strong penetration capability of neutrons enables in-situ,real-time,and non-destructive detection of structural evolution in most centimeter-level bulk samples under complex environments,and ND allows precise characterization of lattice site occupations for light elements,such as C and O,and neighboring elements.This review discussed the principles of ND,experiment procedures,and data analysis.Combining with recent advances in the research about face-centered cubic high-entropy alloy,typical examples of using ND to investigate the deformation behavior were summarized,ultimately revealing deformation mechanisms dominated by dislocations,stacking faults,twinning,and phase transformations.
基金supported by the Natural Science Foundation of China(No.12372176)the National Science and Technology Major Project of China(No.J2019-IV-0007-0075)。
文摘Quantitative assessment of microscale slip activities and plastic localizations is essential for understanding the complex deformation mechanisms in crystalline materials.However,few experimental studies have been able to dynamically measure the deformation fields of rapidly evolving slip activities at the microscale.In this study,we used the Sampling Moire?Method(SMM)to directly measure the dynamic deformation fields of slip activities in Nickel-Based Single-Crystal(NBSC)superalloy under in-situ tensile test,and the strain and displacement fields under the evolving microplastic events with intense slip activities around the notch of the NBSC superalloy specimen were obtained for the first time.The dynamic evolution of slip bands was quantitatively characterized through detailed statistical analysis of strains and displacements under different loads.The locations of the initial appearance of slip traces were successfully predicted by the regions of plasticity localization.The results show that the deformation fields exhibit both high spatial and temporal resolutions,enabling the capture of nanometer-scale displacement fields and visualization of the dynamic fluidity of slip accumulation.This method demonstrates the superiority of the dynamic characterization of the plastic deformation field at the microscale and the promise of its application for characterizing the slip activities of various crystalline metals.
基金supported by the National Science and Technology Major Project,China(No.2017-II-0006-0019)the National Natural Science Foundation of China(No.52375266)the Shaanxi Science Foundation for Distinguished Young Scholars,China(No.2022JC-36)。
文摘A Hybrid Free-Form Deformation(HFFD)method is developed to improve shape preservation in mesh deformation for perforated surfaces,which traditional Free-Form Deformation(FFD)techniques struggle to handle effectively.The proposed method enables high-fidelity parameterized deformation for both flat and curved perforated surfaces while maintaining mesh quality with minimal geometric distortion.To evaluate its effectiveness,comparative studies between HFFD and conventional FFD methods are conducted,demonstrating superior performance in mesh quality and geometric fidelity.The HFFD-based framework is further applied to the Multidisciplinary Design Optimization(MDO)of a double-wall turbine blade leading edge.Results indicate an 11.6%increase in cooling efficiency and a 16.21%reduction in maximum stress.Additionally,compared to traditional geometry-based parameterization in MDO,the HFFD approach improves model processing efficiency by 84.15%and overall optimization efficiency by20.05%.These findings demonstrate HFFD's potential to significantly improve complex engineering design optimization by achieving precise shape preservation and improving computational efficiency.
基金Project supported by the National Natural Science Foundation of China(Nos.124B2043,U2241267,12172155,and 12302278)the Science and Technology Leading Talent Project of Gansu Province of China(No.23ZDKA0009)the Natural Science Foundation of Gansu Province of China(Nos.24JRRA473 and 24JRRA489)。
文摘The contact deformation and buckling of elastic rods against rigid surfaces represent a prevalent phenomenon in applications such as oil drilling,arterial stents,and energy harvesting.This has attracted widespread attention from researchers.In this paper,the deformation and buckling behaviors of a circular arch subject to compression by a rigid plate are investigated with a planar elastic rod model that incorporates tension,shearing,and bending.In comparison with the existing models that solely consider the bending energy,the deflection curve,the internal force distribution,and the critical load of the present model show good agreement with the finite element results.Through the dimensional analysis and order-of-magnitude estimation,we examine the factors influencing the critical load.The study reveals that the semi-central angle of the arch has the most significant effect.The dimensionless geometric parameter describing arch slenderness becomes prominent when the semi-central angle is less than 30°,while Poisson's ratio and the cross-sectional shear correction factor exhibit negligible influence.Furthermore,the variation in the proportions of strain energy components during critical buckling is presented with respect to the semi-central angle and the geometric parameter,thereby delineating the applicable ranges of both the original model(OM)and the modified model(MM).
文摘Central Sumatra,Indonesia,is historically known for its significant seismic activities,most notably the devastating 1883 earthquake.In this study,we measured the interseismic deformation using continuous GNSS observation data for three years from 2018 to 2021.5.The results show that the derived velocity fields indicate that the Central Sumatra deformation is primarily characterized by crustal strain shortening due to interaction between the India-Australian plate and the Sundaland plate.High strain values are observed along the Sumatran Fault Zone(SFZ),which is characterized by a history of significant seismic activity.Interseismic locking is divided into two segments.Segment A,located in the northern part of Siberut Island has an estimated moment magnitude of MW7.44 with a return period of200 years leading to a potential earthquake magnitude of MW8.98.Segment B in the southern part of Siberut Island has an estimated moment magnitude of MW7.26 with a return period of 200 years,resulting in a potential earthquake magnitude of MW8.79.The findings highlight critical seismic hazard implications,emphasizing the potential for a major earthquake in the Central Sumatra.
基金supported in part by the Mining Hydraulic Technology and Equipment Engineering Research Center,Liaoning Technical University,Fuxin,China(Grant No.MHTE23-R04)the Fundamental Research Funds for the Central Universities(ID N25BSS068).
文摘This study presents an implicit multiphysics coupling method integrating Computational Fluid Dynamics(CFD),the Multiphase Particle-in-Cell(MPPIC)model,and the Finite Element Method(FEM),implemented with OpenFOAM,CalculiX,and preCICE to simulate fluid-particle-structure interactions with large deformations.Mesh motion in the fluid field is handled using the radial basis function(RBF)method.The particle phase is modeled by MPPIC,where fluid-particle interaction is described through momentum exchange,and inter-particle collisions are characterized by collision stress.The structural field is solved by nonlinear FEM to capture large deformations induced by geometric nonlinearity.Coupling among fields is realized through a partitioned,parallel,and non-intrusive iterative strategy,ensuring stable transfer and convergence of interface forces and displacements.Notably,the influence of particles on the structure is not direct but mediated by the fluid,while structural motion directly affects particle dynamics.The results demonstrate that the proposed approach effectively captures multiphysics interaction processes and provides a valuable reference for numerical modeling of coupled fluid-particle-structure systems.
文摘Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted drug delivery.For implants,mechanical properties are key performance characteristics,so understanding the deformation and failure mechanisms is essential for selecting the appropriate implant structure.The deformation and fracture processes in PLA samples with different interior architectures have been studied through computer simulation and experimental research.Two TPMS topologies,the Schwarz Diamond and Gyroid architectures,were used for the sample construction by 3D printing.ANSYS software was utilized to simulate compressive deformation.It was found that under the same load,the vonMises stresses in the Gyroid structure are higher than those in the Schwartz Diamond structure,which was associated with the different orientations of the cells in the studied structures in relation to the direction of the loading axis.The deformation process occurs in the local regions of the studied TPMS structures.Maximum von Mises stresses were observed in the vertical parts of the structures oriented along the load direction.It was found that,unlike the Gyroid,the Schwartz Diamond structure contains a frame that forms unique stiffening ribs,which ensures the redistribution of the load under the vertical loading direction.An analysis of the mechanical characteristics of PLA samples with the Schwartz Diamond and Gyroid structures produced by the Fused Deposition Modeling(FDM)method was correlated with computer simulation.The Schwarz Diamond-type structure was shown to have a higher absorption energy than the Gyroid one.A study of the fracture in PLA samples with various cell sizes revealed a particular feature related to the samples’periodic surface topology and the 3D printing process.Scanning electron microscopic(SEM)studies of the samples deformed by compression showed thatwith an increase in the density of the samples,the failure mechanism changes from ductile to quasi-brittle due to the complex participation of both cell deformation and fiber deformation.
基金Supported by National Natural Science Foundation of China(Grant No.52275412)Fundamental Research Funds for the Central Universities of China(Grant No.N2403015).
文摘High entropy alloy attracts widespread attention due to its excellent mechanical properties.It becomes a new type of alloy material with high application potential,but the grinding performance of High entropy alloy receives little attention.This paper conducts grinding simulation and surface grinding experiments on FeCoCrNi high entropy and alloys to analyze the grinding removal mechanism of the FeCoCrNi-based High entropy alloy.We also discuss the influence of grinding parameters,element types,element content and forming methods on grinding force and sub-surface plastic deformation after grinding.The simulation and experimental results show that as the increase of grinding depth,both tangential grinding force and normal grinding force increase,and the thickness of sub-surface plastic deformation layer decreases.With the increase of grinding speed,both tangential grinding force and normal grinding force decrease,and the thickness of sub-surface plastic deformation layer caused by grinding process shows a trend of gradual decrease.Under the same processing parameters,the normal grinding force is greater than the tangential grinding force.In FeCoCrNi series high entropy alloys,the grinding force and subsurface plastic deformation layer thickness of high entropy alloys increased with the addition in Ti content.The grinding force and plastic deformation formed by adding Ti element are greater than those formed by adding Al element,and High entropy alloys prepared using laser cladding method exhibit greater grinding force and plastic deformation than those prepared using selective laser melting method.The research results provide theoretical reference and experimental basis for high-quality grinding of high entropy alloys,which may be helpful for the design and manufacturing of high entropy alloy parts.
基金supported by the China Postdoctoral Science Foundation(CPSF)(Grant No.2024M762769)the Natural Science Basic Research Program of Shaanxi(Grant No.2024JC-YBQN-0333)the Postdoctoral Fellowship Program of CPSF(Grant No.GZC20232230).
文摘Slopes are likely to fail in areas with frequent rainfall and earthquakes.The deformation characteristics of unsaturated slopes subjected to post-rainfall earthquakes are investigated using centrifuge model tests and finite element analyses.Three tests of the slope deformation under earthquake and post-rainfall earthquakes are first studied using image analysis techniques.Then,based on an elastoplastic constitutive model,numerical simulations are carried out using the finite element method and compared with the centrifuge test results.Finally,a parametric study is performed to clarify the effects of antecedent rainfall on earthquake-induced slope deformation.The results show that slope deformation caused by post-rainfall earthquakes differs from that caused by earthquakes without antecedent rainfall.The seepage flow and soil strength of the slope are affected by previous rainfall conditions,such as intensity and duration,which directly influence the slope deformation caused by the subsequent earthquake.Soil displacement and strain become greater and the slip surface is more noticeable during the post-rainfall earthquake of higher intensity.In addition,the time interval between the rainfall and the earthquake has a considerable impact on the detailed characteristics of the slope deformation,and the significant deformation occurs at the time of lowest soil strength when seepage flow reaches the lower part of the slope.Moreover,the repeated intermittent rainfall greatly affects the subsequent earthquake-induced slope deformation,the main characteristics of which are closely related to the changes in saturation and strength of the slope.However,with the prolonged time gap between each round of rainfall,the earthquake-induced slope deformation becomes insignificant.
基金support of her postdoctoral research at the GFZ Helmholtz Centre for Geosciences.P.Pan acknowledges the financial support of the National Natural Science Foundation of China(Grant No.52339001)H.Hofmann and Y.Ji acknowledge the financial support of the Helmholtz Association's Initiative and Networking Fund for the Helmholtz Young Investigator Group ARES(contract number VH-NG-1516).
文摘A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.
基金National Natural Science Foundation of China(Grant Nos.41930101 and 42101096)the China Postdoctoral Science Foundation(No.2019M660091XB)+8 种基金the Key Research and Development Project of Ecological Civilization Construction in Gansu Province(No.24YFFA054)the Natural Science Foundation of Gansu Province(Grant Nos.23JRRA857,23JRRG0015,and 21JR7RA317)the Gansu Province Higher Education Institutions Young Doctor(2024QB-046)the Open Fund of Wuhan,Gravitational Field and Solid Tides,National Field Observation and Research Station(WHYWZ202403)the National Cryosphere Desert Data Center(No.E01Z790201/2021kf07)the Lanzhou Talent Innovation and Entrepreneurship(No.2022-RC-73)the Experimental Teaching Reform Project of Lanzhou Jiaotong University(2024002)the Undergraduate Teaching Reform Project of Lanzhou Jiaotong University(JGY202416)"Young Scientific and Technological Talents Supporting Project"Project of Gansu Province(Li Wei)。
文摘An MW6.0 earthquake struck Jishishan County in Linxia Prefecture,Gansu Province,on December 18,2023.In this research,Sentinel-1A satellite radar observations were used to obtain the field of coseismic deformation of the Jishishan earthquake in 2023,and the geometric and fine slip distribution of the seismogenic fault were inverted using this as a constraint.The results show that the earthquake is characterized by thrust movement.The coseismic slip distribution results show that the maximum slip of this earthquake is 0.3 m.The Coulomb stress distribution shows that the whole section of the southern edge of Lajishan fault,the NWW trending segment of the northern edge of Lajishan fault and its NNW trending segment to the south of the epicenter,the northern edge of the West Qinling fault and the segment to the east of the epicenter of the Daotanghe Linxia fault are under stress loading,which indicates an increase in the potential risk of earthquakes.This research discussed the seismogenic characteristics of earthquakes and the tendency of faults.We speculate that the Jishishan earthquake is the result of the joint action of regional faults and tectonic stress.Based on the observation of seismic data,geodesy,and other geological and geophysical data,we believe that the earthquake was caused by the activation of weak areas under the crust by the local stress from the driving mechanism of the northeast expansion of Qinghai-Xizang Plateau.The seismogenic fault of this earthquake is more likely to be northeast dipping under the comprehensive consideration of various factors,which occurred on the concealed fault belonging to the eastern edge of the Jishishan fault zone.
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)the Ministry of Trade,Industry&Energy(MOTIE)of the Republic of Korea Program(No.RS-2025-02603127,Innovation Research Center for Zero-carbon Fuel Gas Turbine Design,Manufacture,and Safety)。
文摘Understanding the temperature dependent deformation behavior of Mg alloys is crucial for their expanding use in the aerospace sector.This study investigates the deformation mechanisms of hot-rolled AZ61 Mg alloy under uniaxial tension along rolling direction(RD)and transverse direction(TD)at-50,25,50,and 150℃.Results reveal a transition from high strength with limited elongation at-50℃ to significant softening and maximum ductility at 150℃.TD samples consistently showed 2%-6%higher strength than RD;however,this yield anisotropy diminished at 150℃ due to the shift from twinning to thermally activated slip and recovery.Fractography indicated a change from semi-brittle to fully ductile fracture with increasing temperature.Electron backscattered diffraction(EBSD)analysis confirmed twinning-driven grain refinement at low temperatures,while deformation at high temperatures involved grain elongation along shear zones,enabling greater strain accommodation before material failure.
基金financially supported by the National Natural Science Foundation of China(Nos.51909023 and 51775077)the Natural Science Foundation of Liaoning Province(No.2021-MS-140)the Fundamental Research Funds for the Central Universities(No.3132025114)。
文摘Ultra-high molecular weight polyethylene(UHMWPE)is a key material for marine applications owing to its outstanding self-lubrication and corrosion resistance.However,its long-term performance is compromised by plastic deformation in seawater.In this study,we performed a comparative analysis of the UHMWPE dynamics under seawater and water conditions to investigate the plastic deformation of UHMWPE induced by seawater.The results show that the plastic deformation of UHMWPE is amplified in seawater relative to the water conditions.Under thin fluid conditions,frictional interfaces exhibit a higher interfacial friction force and interaction energy in seawater than in water.Compared to freely diffused water molecules,hydrated ions occupy larger interchain spaces within polyethylene.Furthermore,the diffusion of hydrated ions weakens the interchain interactions,promoting more severe polyethylene chain rearrangement and accelerating seawater-induced plastic deformation in UHMWPE during friction.Furthermore,the diffused seawater accelerated the disentangling of the polyethylene chains and enhanced the orderly orientation distribution of polyethylene.Compared to free water molecules,the water molecules of hydrated ions exhibit enhanced attraction to free-flowing water molecules,thereby accelerating seawater flow across submerged UHMWPE surfaces.This flow enhancement promotes surface polyethylene chain mobility in seawater.
基金supported by the National Natural Science Foundation of China(Grant Nos.52025053 and 52235006)the Jilin Provincial Scientific and Technological Development Program(20220204119YY)the Natural Science Foundation of Shandong Province(ZR2023ME154)。
文摘Ceramic 4D printing,which integrates dynamic deformation with additive manufacturing,demonstrates significant potential in intelligent manufacturing,on-demand shaping of complex structures,and multifunctional device development.Its core advantage lies in endowing materials with environmentally responsive dynamic deformation capabilities.However,current technologies still face limitations in responsiveness,reversibility,and mechanical performance.To address these challenges,this study proposes a programmable ceramic precursor system based on synergistic reinforcement of phase-separating hydrogels and shape memory polymers,combined with a nano-ceramic particle enhancement strategy.Using stereolithography 3D printing,high-precision fabrication of complex structures was achieved.By adjusting precursor composition,programming time,and structural thickness,the phase-separation kinetics-driven delayed recovery mechanism was elucidated,enabling precise control over recovery onset time.Furthermore,the thermal response mechanism of the precursor materials is explored,along with their potential for multi-shape transformation in biomedical applications,which is further extended to shape memory polymer systems.By employing a layered printing strategy,the autonomous reversible deformation of ceramic precursors is realized,providing new possibilities for specific applications.
基金supported by the National Natural Science Foundation of China(Grant Nos.52069029,52369026)the Belt and Road Special Foundation of National Key Laboratory of Water Disaster Preven-tion(Grant No.2023490411)+2 种基金the Yunnan Agricultural Basic Research Joint Special General Project(Grant Nos.202501BD070001-060,202401BD070001-071)Construction Project of the Yunnan Key Laboratory of Water Security(No.20254916CE340051)the Youth Talent Project of“Xingdian Talent Support Plan”in Yunnan Province(Grant No.XDYC-QNRC-2023-0412).
文摘Deformation prediction for extra-high arch dams is highly important for ensuring their safe operation.To address the challenges of complex monitoring data,the uneven spatial distribution of deformation,and the construction and optimization of a prediction model for deformation prediction,a multipoint ultrahigh arch dam deformation prediction model,namely,the CEEMDAN-KPCA-GSWOA-KELM,which is based on a clustering partition,is pro-posed.First,the monitoring data are preprocessed via variational mode decomposition(VMD)and wavelet denoising(WT),which effectively filters out noise and improves the signal-to-noise ratio of the data,providing high-quality input data for subsequent prediction models.Second,scientific cluster partitioning is performed via the K-means++algorithm to precisely capture the spatial distribution characteristics of extra-high arch dams and ensure the consistency of deformation trends at measurement points within each partition.Finally,CEEMDAN is used to separate monitoring data,predict and analyze each component,combine the KPCA(Kernel Principal Component Analysis)and the KELM(Kernel Extreme Learning Machine)optimized by the GSWOA(Global Search Whale Optimization Algorithm),integrate the predictions of each component via reconstruction methods,and precisely predict the overall trend of ultrahigh arch dam deformation.An extra high arch dam project is taken as an example and validated via a comparative analysis of multiple models.The results show that the multipoint deformation prediction model in this paper can combine data from different measurement points,achieve a comprehensive,precise prediction of the deformation situation of extra high arch dams,and provide strong technical support for safe operation.
基金financial support from NSF ExpandQISE program.The synthesis of tellurene was supported by NSF under grant no.CMMI-2046936supports from Purdue Research Foundation.
文摘Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金supported by the Natural Science Foundation of Henan Province(No.252300421478)the National Natural Science Foundation of China(Nos.11975209,U2032211,12075287)。
文摘The high-order deformation effects in even-even^(246,248)No are investigated by means of pairing self-consistent WoodsSaxon-Strutinsky calculations using the potential-energy-surface(PES)approach in an extended deformation space(β_(2),β_(3),β_(4),β_(5),β_(6),β_(7),β_(8)).Based on the calculated two-dimensional projected energy maps and different potential energy curves,we found that the highly even-order deformations have an important impact on both the fission trajectory and energy minima,while the odd-order deformations,accompanying the even-order ones,primarily affect the fission path beyond the second barrier.Relative to the light actinide nuclei,the nuclear ground state changes to the superdeformed configuration,but the normally deformed minimum,as the low-energy shape isomer,may still be primarily responsible for enhancing nuclear stability and ensuring experimental accessibility in^(246,248)No.Our present investigation indicates the nonnegligible impact of high-order deformation effects along the fission valley and will be helpful for deepening the understanding of different deformation effects and deformation couplings in nuclei,especially in this neutron-deficient heavy-mass region.
