Superior strength and high-temperature performance make γ-TiAl vital for lightweight aero-engines. However, its inherent brittleness poses machining problems. This study employed Elliptical Ultrasonic Vibration Milli...Superior strength and high-temperature performance make γ-TiAl vital for lightweight aero-engines. However, its inherent brittleness poses machining problems. This study employed Elliptical Ultrasonic Vibration Milling (EUVM) to address these problems. Considering the influence of machining parameters on vibration patterns of EUVM, a separation time model was established to analyze the vibration evolutionary process, thereby instructing the cutting mechanism. On this basis, deep discussions regarding chip formation, cutting force, edge breakage, and subsurface layer deformation were conducted for EUVM and Conventional Milling (CM). Chip morphology showed the chip formation was rooted in the periodic brittle fracture. Local dimples proved that the thermal effect of high-speed cutting improved the plasticity of γ-TiAl. EUVM achieved a maximum 18.17% reduction in cutting force compared with CM. The force variation mechanism differed with changes in the cutting speed or the vibration amplitude, and its correlation with thermal softening, strain hardening, and vibratory cutting effects was analyzed. EUVM attained desirable edge breakage by achieving smaller fracture lengths. The fracture mechanisms of different phases were distinct, causing a surge in edge fracture size of γ-TiAl under microstructural differences. In terms of subsurface deformation, EUVM also showed strengthening effects. Noteworthy, the lamellar deformation patterns under the cutting removal state differed from the quasi-static, which was categorized by the orientation angles. Additionally, the electron backscattering diffraction provided details of the influence of microstructural difference on the orientation and the deformation of grains in the subsurface layer. The results demonstrate that EUVM is a promising machining method for γ-TiAl and guide further research and development of EUVM γ-TiAl.展开更多
Inconel 718,a nickel,chrome and iron alloy,has special advantages,such as high-temperature strength,thermal resistance and corrosion resistance,which facilitate wide usage in the aerospace industry,especially in the h...Inconel 718,a nickel,chrome and iron alloy,has special advantages,such as high-temperature strength,thermal resistance and corrosion resistance,which facilitate wide usage in the aerospace industry,especially in the hot sections of gas turbine engines.However,machining this alloy is correlated closely with the material’s inherent properties such as excellent combination of strength,hardness and toughness,low thermal conductivity and the tendency to adhere to cutting tools.This nickel alloy also contains inclusions of hard abrasive carbide particles that lead to work-hardening of the workpiece material and thus abrasive wear of the cutting tool.That is,the machining of Inconel 718 is always influenced by high mechanical and thermal loads.This article reviews the chip formation mechanism of Inconel 718.One of the main characteristics in machining of Inconel 718 is that it will produce serrated or segmented chips in a wide range of cutting speeds and feeds.Existing studies show that the chip serration or segmentation by shear localization affects the machined surface integrity,and also contributes to the chip’s evacuation and the automation of machining operations.Thus,research conclusion indicates that the serrated or segmented chip phenomenon is desirable in reducing the level of cutting force,and detailed analysis of models and approaches to understand the chip formation mechanism of Inconel 718 is vital for machining this alloy effectively and efficiently.Therefore,this article presents some summaries on the models and approaches on the chip formation in machining of Inconel 718.展开更多
A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool ...A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool tip and tool run-out, while the simplified circular trajectory and the neglected run-out create negligible change in conventional-scale chip formation models. Newton-Raphson iterative method is employed during the calculation to obtain quadratic convergence. The proposed approach allows the calculation of instantaneous uncut chip thickness to be done accurately and rapidly, and the prediction accuracy of this model is also verified by comparing the simulation results to experimental cutting forces.展开更多
A two-dimensional finite element(FE)model for the high speed turning operations when orthogonally machining AISI H13 tool steel at 49HRC using poly crystalline cubic boron nitride(PCBN)is described.An arbitrary Lagran...A two-dimensional finite element(FE)model for the high speed turning operations when orthogonally machining AISI H13 tool steel at 49HRC using poly crystalline cubic boron nitride(PCBN)is described.An arbitrary Lagrangian Eulerian(ALE)method has been adopted which does not need any chip separation criteria as opposed to the traditional Lagrangian approach.Through FE simulations temperature and stresses distributions are presented that could be helpful in predicting tool life and improving process parameters.The results show that high temperatures are generated along the tool rake face as compared to the shear zone temperatures due to high thermal conductivity of PCBN tools.展开更多
High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting sp...High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting speed,vc=190-300 m/min;cutting depth of axial,ap=5,7 mm),saw-tooth chips were produced in these experiments.During the macro and micro analysis of the Ti-6Al-4V chips,an optical microscope and a scanning electron microscope(SEM)were used to study the microstructure and the morphology of the chips,and the X-ray photoelectron spectroscopy(XPS)was employed for chemical analysis.Comparisons were made to study the influence of different cutting media(nitrogen-oil-mist,air-oil-mist and dry cutting condition)on chip formation.Results indicate that cutting media have significant effects on chip formation.Nitrogen-oil-mist is more suitable for improving the contact condition at chip-tool interface and increasing the tool life in high speed milling of Ti-6Al-4V alloy than air-oil-mist and dry cutting.展开更多
A two-dimensional coupled thermo-mechanical model is used to simulate the progress of milling mild carbon steel with continuous chip formation. Deformation of the workpiece is treated as elastic-plastic with isotropic...A two-dimensional coupled thermo-mechanical model is used to simulate the progress of milling mild carbon steel with continuous chip formation. Deformation of the workpiece is treated as elastic-plastic with isotropic strain-hardening. An analysis of the properties of temperature-dependent materials is employed. The chip separation is achieved by the adaptive remeshing strategy module found in commercial finite element code Marc. In order to increase the computational efficiency and accuracy, we implement a customized subroutine into the Marc code to define local refinement at the tool tip. Measurements are taken of the shape of the chip, the temperature, stress, strain and strain-rate fields. The values of the cutting forces obtained from the simulations agree well with those obtained from the cutting experiments.展开更多
The miniaturisation context leads to the rise of micro-machining processes. Micro-milling is one of the most flexible and fast of them. Although it is based on the same principles as macro-cutting, it is not a simple ...The miniaturisation context leads to the rise of micro-machining processes. Micro-milling is one of the most flexible and fast of them. Although it is based on the same principles as macro-cutting, it is not a simple scaling-down of it. This down-sizing involves new phenomena in the chip formation, such as the minimum chip thickness below which no chip is formed. This paper presents a review of the current state of the art in this field from an experimental and a numerical point of view. A 2D finite element model is then developed to study the influence of the depth of cut on the chip formation. After the model validation in macro-cutting, it highlights the phenomena reported in literature and allows to perform a minimum chip thickness estimation.展开更多
Alumina dispersion-strengthened copper (ADSC), as a representative particle-reinforced metal matrix composite (PRMMC), exhibits superior wear resistance and high strength. However, challenges arise in their processabi...Alumina dispersion-strengthened copper (ADSC), as a representative particle-reinforced metal matrix composite (PRMMC), exhibits superior wear resistance and high strength. However, challenges arise in their processability because of the non-uniform material properties of biphasic materials. In particular, limited research has been conducted on the reinforcement mechanism and behavior of particles during material cutting deformation of PRMMC with nanoscale particles. In this study, a cutting simulation model for ADSC was established, separating the nanoscale reinforcement particles from the matrix. This model was utilized to analyze the interactions among particles, matrix, and tool during the cutting process, providing insights into chip formation and fracture. Particles with high strength and hardness are more prone to storing stress concentrations, anchoring themselves at grain boundaries to resist grain fibration, thereby influencing the stress distribution in the cutting deformation zone. Stress concentration around the particles leads to the formation of discontinuous chips, indicating that ADSC with high-volume fractions of particle (VFP) exhibits low cutting continuity, which is consistent with the results of cutting experiments. The tool tip that is in contact with particles experiences stress concentration, thereby accelerating tool wear. Cutting ADSC with 1.1% VFP results in tool blunting, which increases the radius of cutting edge from 0.5 to 1.9 μm, accompanied with remarkable coating delamination and wear. Simulation results indicate that the minimum uncut chip thickness increases from 0.04 to 0.07 μm as VFP increases from 0.3% to 1.1%. In conjunction with scratch experiments, MUCT increases with the augmentation of VFP. Computational analysis of the specific cutting force indicates that particles contribute to the material’s size effect. The results of this study provide theoretical guidance for practical engineering machining of ADSC, indicating its great importance for the process design of components made from ADSC.展开更多
In this study, molecular dynamics simulations were carried out to study the effect of machining velocities on the mechanism of chip formation in nano-metric copper. A wide range of cutting velocities was performed fro...In this study, molecular dynamics simulations were carried out to study the effect of machining velocities on the mechanism of chip formation in nano-metric copper. A wide range of cutting velocities was performed from 10 to 2000 m/s, and the microstructure's evolution from a crystalline state to an amorphous state was studied. At the low machining velocity, dislocations were generated from the surface in front of the tool, and the immobile dislocation deduced by the cross slip of dislocation was observed. At the high machining velocity, no crystal dislocation nucleated, but instead disorder atoms were found near the tool. Temperature near the tool region increased with the increasing machining velocities, and the temperature had an important effect on the phase transition of the crystal structure.展开更多
Imaging techniques have been widely implemented to study the dynamics of chip formation.They can offer a direct method and a full field measurement of the cutting process,providing kinematic information of the chip fo...Imaging techniques have been widely implemented to study the dynamics of chip formation.They can offer a direct method and a full field measurement of the cutting process,providing kinematic information of the chip formation process.In this article,the state of the art of the imaging techniques reported in the literature has been summarized and analyzed.The imaging techniques have been applied to study the chip formation mechanism,friction behavior,strain/strain rate,and stress fields.Furthermore,the study of surface integrity has been advanced by deriving the thermo‐mechanical loading,subsurface deformation,and material constitutive model from the imaging technique.Finally,achievements in the area of imaging techniques have been summarized,followed by future directions for their application in the study of surface integrity.展开更多
The mechanochemical effect on the microcutting of AA6061 alloy is studied through characterization on the chip. A pronounced reduction of machining forces and chip thickness was observed with mechanochemical effect du...The mechanochemical effect on the microcutting of AA6061 alloy is studied through characterization on the chip. A pronounced reduction of machining forces and chip thickness was observed with mechanochemical effect during microcutting. Furthermore, electron backscattered diffraction(EBSD) and transmission electron microscopy(TEM) observations were performed on the chips and shear bands. The result reveals much coarser grains(24.6 μm in size) in the surfactant-affected chip than that in the surfactant-free chip(13.5 μm). Different grain orientations are induced by microcutting. {100}<001> and{110}<112> grain orientations are majority for surfactant-free chip, and {110}<001> and {100}<110>dominate most for all grain orientations for surfactant-affected chip. Additionally, since less localized shear strain and lower temperature are generated inside the shear band with mechanochemical effect,almost no recrystallization phenomena can be observed in this region. TEM analysis shows that fewer subgrains and dislocations could be observed inside the shear band of the surfactant-affected chip in comparison with the surfactant-free chip. Based on the high-resolution transmission electron microscopic(HRTEM) observations, dislocations were observed at the atomic scale. The results show that the main dislocation motion mode in shear bands of surfactant-free and surfactant-affected chips are dislocation climb and dislocation glide, respectively.展开更多
Percussive drilling is gaining interest for both shallow and deep applications due to its potential for higher drilling rates in hard rocks.Therefore,for efficient rock breaking,the development of advanced percussive ...Percussive drilling is gaining interest for both shallow and deep applications due to its potential for higher drilling rates in hard rocks.Therefore,for efficient rock breaking,the development of advanced percussive drilling simulation tools has the potential to be transformative.Such tools must accurately capture the rock’s response to enable an effective analysis of the fragmentation process.Traditional continuum numerical methods,such as the finite element method(FEM),do not simulate discrete cracks or the contact interaction between rock fragments.The finite-discrete element method(FDEM)is a three-dimensional hybrid method that combines FEM with the discrete element method(DEM)that addresses these limitations.New FDEM simulation results of impacts on Kuru Grey granite show good agreement with published experimental data.The interpretation focuses on two significant processes in percussive drilling:crack propagation and chipping generation.FDEM successfully simulates the evolution of cracks,including radial,side,and inclined cracks,as well as crushed and cracked zones.The simulation also reproduces the coalescence of adjacent craters to generate more chippings.Additionally,the stress state,velocity field and discrete fractures simulated by FDEM provide detailed insights into the different fracture patterns for Kuru Grey granite,enhancing understanding of the fundamental underlying mechanisms.展开更多
The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties.Creep feed grinding is one of the essential operati...The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties.Creep feed grinding is one of the essential operations during the whole component manufacturing processes.In this work,the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated.A variety of responses including grinding forces,temperature fields,specific grinding energy,surface integrity and chip modes were carefully recorded.Besides,the mechanism of ground surface profile generation and the spatial frequency spectrum of the surface profile were tentatively analyzed.It was found that the wheel speed has a relative influence on the grinding forces and temperatures of which the work hardening effect dominates the material removal with lower wheel speed while the thermal softening becomes crucial as the wheel speed exceeds the critical value for the studied 300M steel.Furthermore,a scattered spatial frequency spectrum for the generated surface profile was noticed with lower wheel speed while the spectrum gathers towards the lower frequency values with higher amplitude as the wheel speed increases.The shearing chip and flowing chip dominates the main chip type,indicating the excellent abrasive sharpness during the grinding process.In general,the used zirconium corundum wheel presents feasibility for the creep feed grinding of 300M steel because of the high material removal rate,absence of surface burn,low wheel wear and higher compressive residual stresses.展开更多
Gamma titanium-aluminum intermetallic compounds(γ-TiAl)have gained considerable attentions in the aerospace industry due to their exceptional thermal resilience and comprehensive attributes,making them a prime exampl...Gamma titanium-aluminum intermetallic compounds(γ-TiAl)have gained considerable attentions in the aerospace industry due to their exceptional thermal resilience and comprehensive attributes,making them a prime example of lightweight and advanced materials.To address the frequent occurrence of burns and severe tool deterioration during the process of high-efficiency deep grinding(HEDG)onγ-TiAl alloys,ultrasonic vibration-assisted high-efficiency deep grinding(UVHEDG)has been emerged.Results indicate that in UVHEDG,the grinding temperature is on average 15.4%lower than HEDG due to the employment of ultrasonic vibrations,enhancing coolant penetration into the grinding area and thus reducing heat generation.Besides,UVHEDG possesses superior performance in terms of grinding forces compared to HEDG.As the material removal volume(MRV)increases,the tangential grinding force(F_(t))and normal grinding force(F_(n))of UVHEDG increase but to a lesser extent than in HEDG,with an average reduction of16.25%and 14.7%,respectively.UVHEDG primarily experiences microfracture of grains,whereas HEDG undergoes large-scale wear later in the process due to increased grinding forces.The surface roughness(R_(a))characteristics of UVHEDG are superior,with the average value of R_(a)decreasing by 46.5%compared to HEDG as MRV increases.The surface morphology in UVHEDG exhibits enhanced smoothness and a shallower layer of plastic deformation.Grinding chips generated by UVHEDG show a more shear-like shape,with the applied influence of ultrasonic vibration on chip morphology,thereby impacting material removal behaviors.These aforementioned findings contribute to enhanced machining efficiency and product quality ofγ-TiAl alloys after employing ultrasonic vibrations into HEDG.展开更多
Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-m...Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-milling orAl6061-T6. Finite element （FE） simulations were performed under different cutting conditions to obtain realistic numerical predictions of chip flow, burr formation, and cutting forces. FE modeling displayed notable advantages, such as capability to easily handle any type of tool geometry and any side effect on chip formation, including thermal aspect and material property changes. The proposed 3D FE model considers the effects ofmiU helix angle and cutting edge radius on the chip. The prediction capability of the FE model was validated by comparing numerical model and experimental test results. Burr dimension trends were correlated with force profile shapes. However, the FE predictions overestimated the real force magnitude. This overestimation indicates that the model requires further development.展开更多
Cortical bone is semi-brittle and anisotropic,that brings a challenge to suppress vibration and avoid undesired fracture in precise cutting process in surgeries.In this paper,a novel analytical model is proposed to re...Cortical bone is semi-brittle and anisotropic,that brings a challenge to suppress vibration and avoid undesired fracture in precise cutting process in surgeries.In this paper,a novel analytical model is proposed to represent cortical bone cutting processes.The model is utilized to predict the chip formations,material removal behavior and cracks propagation under varying bone osteon cutting angles and depths.Series of orthogonal cutting experiments were conducted on cortical bone to investigate the impact of bone osteon cutting angle and depth of cut on cutting force,crack initialization and propagation.The observed chip morphology highly agreed with the prediction of chip formation based on the analytical model.The curly,serrated,grainy and powdery chips formed when the cutting angle was set as 0°,60°,90°,and 120°,respectively.Cortical bone were removed dominantly by shearing at a small depth of cut from 10 to 50μm,and by a mixture of pealing,shearing,fracture and crushing at a large depth of cut over 100μm at different bone osteon angles.Moreover,its fracture toughness was calculated based on measured cutting force.It is found that the fluctuation of cutting force is suppressed and the bone material becomes easy to remove,which attributes to lower fracture toughness at bone osteon cutting angle 0°.When the cutting direction develops a certain angle to bone osteon,the fracture toughness increases then the crack propagation is inhibited to some extent and the fluctuation of cutting force comparatively decreases.There is a theoretical and practical significance for tools design and operational parameters choice in surgeries.展开更多
This paper studies the influence of radial depth on vibration, chip formation and surface roughness during face milling of AISl3O4 austenitic stainless steel with indexable cemented carbide milling cutters. The amplit...This paper studies the influence of radial depth on vibration, chip formation and surface roughness during face milling of AISl3O4 austenitic stainless steel with indexable cemented carbide milling cutters. The amplitude of vibration acceleration increased with the increasing radial depth up to 80 mm. And the domain vibration frequency varied with the radial depth. In this paper, three types of chips were found： C shape, long shape and spiral shape. The minimum surface roughness value occurred when the radial depth equalled 40 mm in the experiment. Irregular changes of chip curl radius and chip thickness could be attributed to different numbers of alternately engaged teeth when the feed and speed were fixed. Surface roughness is related to forced vibration and chip formation. Radial depth with different numbers of alternately engaged teeth could significantly influence the forced vibration, chip formation, and surface roughness.展开更多
To benefit tissue removal and postoperative rehabilitation,increased efficiency and accuracy and reduced operating force are strongly required in the osteotomy.A novel elliptical vibration cutting(EVC)has been introdu...To benefit tissue removal and postoperative rehabilitation,increased efficiency and accuracy and reduced operating force are strongly required in the osteotomy.A novel elliptical vibration cutting(EVC)has been introduced for bone cutting compared with conventional cutting(CC)in this paper.With the assistance of high-speed microscope imaging and the dynamometer,the material removals of cortical bone and their cutting forces from two cutting regimes were recorded and analysed comprehensively,which clearly demonstrated the chip morphology improvement and the average cutting force reduction in the EVC process.It also revealed that the elliptical vibration of the cutting tool could promote fracture propagation along the shear direction.These new findings will be of important theoretical and practical values to apply the innovative EVC process to the surgical procedures of the osteotomy.展开更多
In this paper the nano-metric simulation of grinding of copper with diamond abrasive grains, using the molecular dynamics （MD） method, is considered. An MD model of nano-scale grinding, where a single diamond abrasi...In this paper the nano-metric simulation of grinding of copper with diamond abrasive grains, using the molecular dynamics （MD） method, is considered. An MD model of nano-scale grinding, where a single diamond abrasive grain performs cutting of a copper workpiece, is presented. The Morse potential function is used to simulate the interactions between the atoms involved in the procedure. In the proposed model, the abrasive grain follows a curved path with decreasing depth of cut within the workpiece to simulate the actual material removal process. Three different initial depths of cut, namely 4 A, 8 A and 12 A, are tested, and the influence of the depth of cut on chip formation, cutting forces and workpiece tempera- tures are thoroughly investigated. The simulation results indicate that with the increase of the initial depth of cut, average cutting forces also increase and therefore the temperatures on the machined surface and within the workpiece increase as well. Furthermore, the effects of the different values of the simulation variables on the chip formation mechanism are studied and discussed. With the appropriate modifications, the proposed model can be used for the simulation of various nano-machining processes and operations, in which continuum mechanics cannot be applied or experimental techniques are subjected to limitations.展开更多
High-performance carbon fiber-reinforced polyether-ether-ketone(CF/PEEK)has been gradually applied in aerospace and automobile applications because of its high strength-to-weight ratio and impact resistance.The drymac...High-performance carbon fiber-reinforced polyether-ether-ketone(CF/PEEK)has been gradually applied in aerospace and automobile applications because of its high strength-to-weight ratio and impact resistance.The drymachining requirement tends to cause the cutting temperature to surpass the glass transition temperature(Tg),leading to poor surface quality,which is the bottleneck for dry milling of CF/PEEK.Temperature suppression has become an important breakthrough in the feasibility of high-speed dry(HSD)milling of CF/PEEK.However,heat partitioning and jet heat transfer mechanisms pose strong challenges for temperature suppression analytical modeling.To address this gap,an innovative temperature suppression analytical model based on heat partitioning and jet heat transfer mechanisms is first developed for suppressing workpiece temperature via the first-time implementation of an air jet cooling process in the HSD milling of UD-CF/PEEK.Then,verification experiments of the HSD milling of UD-CF/PEEK with four fiber orientations are performed for dry and air jet cooling conditions.The chip morphologies are characterized to reveal the formation mechanism and heat-carrying capacity of the chip.The milling force model can obtain the force coefficients and the total cutting heat.The workpiece temperature increase model is validated to elucidate the machined surface temperature evolution and heat partition characteristics.On this basis,an analytical model is verified to predict the workpiece temperature of air jet cooling HSD milled with UD-CF/PEEK with a prediction accuracy greater than 90%.Compared with those under dry conditions,the machined surface temperatures for the four fiber orientations decreased by 30%–50%and were suppressed within the Tg range under air jet cooling conditions,resulting in better surface quality.This work describes a feasible process for the HSD milling of CF/PEEK.展开更多
基金co-supported by the Science Center for Gas Turbine Project, China(No. P2022-AB-IV-001-002)the National Natural Science Foundation of China (No. 91960203)+1 种基金the Fundamental Research Funds for the Central Universities (No. D5000230048)the Innovation Capability Support Program of Shaanxi (No. 2022TD-60)
文摘Superior strength and high-temperature performance make γ-TiAl vital for lightweight aero-engines. However, its inherent brittleness poses machining problems. This study employed Elliptical Ultrasonic Vibration Milling (EUVM) to address these problems. Considering the influence of machining parameters on vibration patterns of EUVM, a separation time model was established to analyze the vibration evolutionary process, thereby instructing the cutting mechanism. On this basis, deep discussions regarding chip formation, cutting force, edge breakage, and subsurface layer deformation were conducted for EUVM and Conventional Milling (CM). Chip morphology showed the chip formation was rooted in the periodic brittle fracture. Local dimples proved that the thermal effect of high-speed cutting improved the plasticity of γ-TiAl. EUVM achieved a maximum 18.17% reduction in cutting force compared with CM. The force variation mechanism differed with changes in the cutting speed or the vibration amplitude, and its correlation with thermal softening, strain hardening, and vibratory cutting effects was analyzed. EUVM attained desirable edge breakage by achieving smaller fracture lengths. The fracture mechanisms of different phases were distinct, causing a surge in edge fracture size of γ-TiAl under microstructural differences. In terms of subsurface deformation, EUVM also showed strengthening effects. Noteworthy, the lamellar deformation patterns under the cutting removal state differed from the quasi-static, which was categorized by the orientation angles. Additionally, the electron backscattering diffraction provided details of the influence of microstructural difference on the orientation and the deformation of grains in the subsurface layer. The results demonstrate that EUVM is a promising machining method for γ-TiAl and guide further research and development of EUVM γ-TiAl.
基金Supported by National Natural Science Foundation of China(Grant Nos.51975481 and 51675440)Fundamental Research Funds for the Central Universities(Grant No.3102020ZX004).
文摘Inconel 718,a nickel,chrome and iron alloy,has special advantages,such as high-temperature strength,thermal resistance and corrosion resistance,which facilitate wide usage in the aerospace industry,especially in the hot sections of gas turbine engines.However,machining this alloy is correlated closely with the material’s inherent properties such as excellent combination of strength,hardness and toughness,low thermal conductivity and the tendency to adhere to cutting tools.This nickel alloy also contains inclusions of hard abrasive carbide particles that lead to work-hardening of the workpiece material and thus abrasive wear of the cutting tool.That is,the machining of Inconel 718 is always influenced by high mechanical and thermal loads.This article reviews the chip formation mechanism of Inconel 718.One of the main characteristics in machining of Inconel 718 is that it will produce serrated or segmented chips in a wide range of cutting speeds and feeds.Existing studies show that the chip serration or segmentation by shear localization affects the machined surface integrity,and also contributes to the chip’s evacuation and the automation of machining operations.Thus,research conclusion indicates that the serrated or segmented chip phenomenon is desirable in reducing the level of cutting force,and detailed analysis of models and approaches to understand the chip formation mechanism of Inconel 718 is vital for machining this alloy effectively and efficiently.Therefore,this article presents some summaries on the models and approaches on the chip formation in machining of Inconel 718.
基金supported by National Natural Science Foundation of China (No.50575134)
文摘A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool tip and tool run-out, while the simplified circular trajectory and the neglected run-out create negligible change in conventional-scale chip formation models. Newton-Raphson iterative method is employed during the calculation to obtain quadratic convergence. The proposed approach allows the calculation of instantaneous uncut chip thickness to be done accurately and rapidly, and the prediction accuracy of this model is also verified by comparing the simulation results to experimental cutting forces.
基金This project is supported by National Natural Science Foundation of China(No.50505003).
文摘A two-dimensional finite element(FE)model for the high speed turning operations when orthogonally machining AISI H13 tool steel at 49HRC using poly crystalline cubic boron nitride(PCBN)is described.An arbitrary Lagrangian Eulerian(ALE)method has been adopted which does not need any chip separation criteria as opposed to the traditional Lagrangian approach.Through FE simulations temperature and stresses distributions are presented that could be helpful in predicting tool life and improving process parameters.The results show that high temperatures are generated along the tool rake face as compared to the shear zone temperatures due to high thermal conductivity of PCBN tools.
基金the National Natural Science Foundation of China (Grant No. 50175051)
文摘High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting speed,vc=190-300 m/min;cutting depth of axial,ap=5,7 mm),saw-tooth chips were produced in these experiments.During the macro and micro analysis of the Ti-6Al-4V chips,an optical microscope and a scanning electron microscope(SEM)were used to study the microstructure and the morphology of the chips,and the X-ray photoelectron spectroscopy(XPS)was employed for chemical analysis.Comparisons were made to study the influence of different cutting media(nitrogen-oil-mist,air-oil-mist and dry cutting condition)on chip formation.Results indicate that cutting media have significant effects on chip formation.Nitrogen-oil-mist is more suitable for improving the contact condition at chip-tool interface and increasing the tool life in high speed milling of Ti-6Al-4V alloy than air-oil-mist and dry cutting.
文摘A two-dimensional coupled thermo-mechanical model is used to simulate the progress of milling mild carbon steel with continuous chip formation. Deformation of the workpiece is treated as elastic-plastic with isotropic strain-hardening. An analysis of the properties of temperature-dependent materials is employed. The chip separation is achieved by the adaptive remeshing strategy module found in commercial finite element code Marc. In order to increase the computational efficiency and accuracy, we implement a customized subroutine into the Marc code to define local refinement at the tool tip. Measurements are taken of the shape of the chip, the temperature, stress, strain and strain-rate fields. The values of the cutting forces obtained from the simulations agree well with those obtained from the cutting experiments.
文摘The miniaturisation context leads to the rise of micro-machining processes. Micro-milling is one of the most flexible and fast of them. Although it is based on the same principles as macro-cutting, it is not a simple scaling-down of it. This down-sizing involves new phenomena in the chip formation, such as the minimum chip thickness below which no chip is formed. This paper presents a review of the current state of the art in this field from an experimental and a numerical point of view. A 2D finite element model is then developed to study the influence of the depth of cut on the chip formation. After the model validation in macro-cutting, it highlights the phenomena reported in literature and allows to perform a minimum chip thickness estimation.
基金supported by the National Key R&D Program of China(Grant No.2023YFC2413303)the National Natural Science Foundation of China(Grant No.52075128)the Natural Science Foundation of Heilongjiang Province,China(Grant No.YQ2020E013).
文摘Alumina dispersion-strengthened copper (ADSC), as a representative particle-reinforced metal matrix composite (PRMMC), exhibits superior wear resistance and high strength. However, challenges arise in their processability because of the non-uniform material properties of biphasic materials. In particular, limited research has been conducted on the reinforcement mechanism and behavior of particles during material cutting deformation of PRMMC with nanoscale particles. In this study, a cutting simulation model for ADSC was established, separating the nanoscale reinforcement particles from the matrix. This model was utilized to analyze the interactions among particles, matrix, and tool during the cutting process, providing insights into chip formation and fracture. Particles with high strength and hardness are more prone to storing stress concentrations, anchoring themselves at grain boundaries to resist grain fibration, thereby influencing the stress distribution in the cutting deformation zone. Stress concentration around the particles leads to the formation of discontinuous chips, indicating that ADSC with high-volume fractions of particle (VFP) exhibits low cutting continuity, which is consistent with the results of cutting experiments. The tool tip that is in contact with particles experiences stress concentration, thereby accelerating tool wear. Cutting ADSC with 1.1% VFP results in tool blunting, which increases the radius of cutting edge from 0.5 to 1.9 μm, accompanied with remarkable coating delamination and wear. Simulation results indicate that the minimum uncut chip thickness increases from 0.04 to 0.07 μm as VFP increases from 0.3% to 1.1%. In conjunction with scratch experiments, MUCT increases with the augmentation of VFP. Computational analysis of the specific cutting force indicates that particles contribute to the material’s size effect. The results of this study provide theoretical guidance for practical engineering machining of ADSC, indicating its great importance for the process design of components made from ADSC.
基金supported by the National Natural Science Foundation of China(Grant Nos.11132011,11021262 and 11172303)the National Basic Research Program of China("973"Project)(Grant No.2012CB937500)
文摘In this study, molecular dynamics simulations were carried out to study the effect of machining velocities on the mechanism of chip formation in nano-metric copper. A wide range of cutting velocities was performed from 10 to 2000 m/s, and the microstructure's evolution from a crystalline state to an amorphous state was studied. At the low machining velocity, dislocations were generated from the surface in front of the tool, and the immobile dislocation deduced by the cross slip of dislocation was observed. At the high machining velocity, no crystal dislocation nucleated, but instead disorder atoms were found near the tool. Temperature near the tool region increased with the increasing machining velocities, and the temperature had an important effect on the phase transition of the crystal structure.
基金National Natural Science Foundation of China,Grant/Award Numbers:51722505,52005200the National Natural Science Foundation of China for funding the projects:“Digital manufacturing and numerical control,”Grant number:51722505,and“Formation mechanism of residual stress in complex surface milling based on in situ imaging technology,”Grant number:52005200.
文摘Imaging techniques have been widely implemented to study the dynamics of chip formation.They can offer a direct method and a full field measurement of the cutting process,providing kinematic information of the chip formation process.In this article,the state of the art of the imaging techniques reported in the literature has been summarized and analyzed.The imaging techniques have been applied to study the chip formation mechanism,friction behavior,strain/strain rate,and stress fields.Furthermore,the study of surface integrity has been advanced by deriving the thermo‐mechanical loading,subsurface deformation,and material constitutive model from the imaging technique.Finally,achievements in the area of imaging techniques have been summarized,followed by future directions for their application in the study of surface integrity.
基金financial support from the Singapore Ministry of Education Academic Research Funds (R-265-000-686-114 and MOE2018-T2-1-140)。
文摘The mechanochemical effect on the microcutting of AA6061 alloy is studied through characterization on the chip. A pronounced reduction of machining forces and chip thickness was observed with mechanochemical effect during microcutting. Furthermore, electron backscattered diffraction(EBSD) and transmission electron microscopy(TEM) observations were performed on the chips and shear bands. The result reveals much coarser grains(24.6 μm in size) in the surfactant-affected chip than that in the surfactant-free chip(13.5 μm). Different grain orientations are induced by microcutting. {100}<001> and{110}<112> grain orientations are majority for surfactant-free chip, and {110}<001> and {100}<110>dominate most for all grain orientations for surfactant-affected chip. Additionally, since less localized shear strain and lower temperature are generated inside the shear band with mechanochemical effect,almost no recrystallization phenomena can be observed in this region. TEM analysis shows that fewer subgrains and dislocations could be observed inside the shear band of the surfactant-affected chip in comparison with the surfactant-free chip. Based on the high-resolution transmission electron microscopic(HRTEM) observations, dislocations were observed at the atomic scale. The results show that the main dislocation motion mode in shear bands of surfactant-free and surfactant-affected chips are dislocation climb and dislocation glide, respectively.
文摘Percussive drilling is gaining interest for both shallow and deep applications due to its potential for higher drilling rates in hard rocks.Therefore,for efficient rock breaking,the development of advanced percussive drilling simulation tools has the potential to be transformative.Such tools must accurately capture the rock’s response to enable an effective analysis of the fragmentation process.Traditional continuum numerical methods,such as the finite element method(FEM),do not simulate discrete cracks or the contact interaction between rock fragments.The finite-discrete element method(FDEM)is a three-dimensional hybrid method that combines FEM with the discrete element method(DEM)that addresses these limitations.New FDEM simulation results of impacts on Kuru Grey granite show good agreement with published experimental data.The interpretation focuses on two significant processes in percussive drilling:crack propagation and chipping generation.FDEM successfully simulates the evolution of cracks,including radial,side,and inclined cracks,as well as crushed and cracked zones.The simulation also reproduces the coalescence of adjacent craters to generate more chippings.Additionally,the stress state,velocity field and discrete fractures simulated by FDEM provide detailed insights into the different fracture patterns for Kuru Grey granite,enhancing understanding of the fundamental underlying mechanisms.
基金supported by the National Natural Science Foundation of China(U19372708)。
文摘The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties.Creep feed grinding is one of the essential operations during the whole component manufacturing processes.In this work,the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated.A variety of responses including grinding forces,temperature fields,specific grinding energy,surface integrity and chip modes were carefully recorded.Besides,the mechanism of ground surface profile generation and the spatial frequency spectrum of the surface profile were tentatively analyzed.It was found that the wheel speed has a relative influence on the grinding forces and temperatures of which the work hardening effect dominates the material removal with lower wheel speed while the thermal softening becomes crucial as the wheel speed exceeds the critical value for the studied 300M steel.Furthermore,a scattered spatial frequency spectrum for the generated surface profile was noticed with lower wheel speed while the spectrum gathers towards the lower frequency values with higher amplitude as the wheel speed increases.The shearing chip and flowing chip dominates the main chip type,indicating the excellent abrasive sharpness during the grinding process.In general,the used zirconium corundum wheel presents feasibility for the creep feed grinding of 300M steel because of the high material removal rate,absence of surface burn,low wheel wear and higher compressive residual stresses.
基金financially supported by the National Natural Science Foundation of China(Nos.92160301,92060203,52175415 and 52205475)the Science Center for Gas Turbine Project(Nos.P2022-AB-Ⅳ-002-001 and P2023-B-Ⅳ-003-001)+4 种基金the Natural Science Foundation of Jiangsu Province(No.BK20210295)the Superior Postdoctoral Project of Jiangsu Province(No.2022ZB215)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX23_0355)the Interdisciplinary Innovation Fund for Doctoral Students of Nanjing University of Aeronautics and Astronautics(KXKCXJJ202305)the Fundamental Research Funds for the Central Universities(Nos.NS2023028 and NG2024015)。
文摘Gamma titanium-aluminum intermetallic compounds(γ-TiAl)have gained considerable attentions in the aerospace industry due to their exceptional thermal resilience and comprehensive attributes,making them a prime example of lightweight and advanced materials.To address the frequent occurrence of burns and severe tool deterioration during the process of high-efficiency deep grinding(HEDG)onγ-TiAl alloys,ultrasonic vibration-assisted high-efficiency deep grinding(UVHEDG)has been emerged.Results indicate that in UVHEDG,the grinding temperature is on average 15.4%lower than HEDG due to the employment of ultrasonic vibrations,enhancing coolant penetration into the grinding area and thus reducing heat generation.Besides,UVHEDG possesses superior performance in terms of grinding forces compared to HEDG.As the material removal volume(MRV)increases,the tangential grinding force(F_(t))and normal grinding force(F_(n))of UVHEDG increase but to a lesser extent than in HEDG,with an average reduction of16.25%and 14.7%,respectively.UVHEDG primarily experiences microfracture of grains,whereas HEDG undergoes large-scale wear later in the process due to increased grinding forces.The surface roughness(R_(a))characteristics of UVHEDG are superior,with the average value of R_(a)decreasing by 46.5%compared to HEDG as MRV increases.The surface morphology in UVHEDG exhibits enhanced smoothness and a shallower layer of plastic deformation.Grinding chips generated by UVHEDG show a more shear-like shape,with the applied influence of ultrasonic vibration on chip morphology,thereby impacting material removal behaviors.These aforementioned findings contribute to enhanced machining efficiency and product quality ofγ-TiAl alloys after employing ultrasonic vibrations into HEDG.
文摘Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-milling orAl6061-T6. Finite element （FE） simulations were performed under different cutting conditions to obtain realistic numerical predictions of chip flow, burr formation, and cutting forces. FE modeling displayed notable advantages, such as capability to easily handle any type of tool geometry and any side effect on chip formation, including thermal aspect and material property changes. The proposed 3D FE model considers the effects ofmiU helix angle and cutting edge radius on the chip. The prediction capability of the FE model was validated by comparing numerical model and experimental test results. Burr dimension trends were correlated with force profile shapes. However, the FE predictions overestimated the real force magnitude. This overestimation indicates that the model requires further development.
基金China Scholarship Council,the National Natural Science Foundation of China(Grant No.52075161)Hunan Provincial Natural Science Foundation of China(Grant No.2022JJ40486)Changsha Municipal Natural Science Foundation of China(Grant No.2022cskj017).
文摘Cortical bone is semi-brittle and anisotropic,that brings a challenge to suppress vibration and avoid undesired fracture in precise cutting process in surgeries.In this paper,a novel analytical model is proposed to represent cortical bone cutting processes.The model is utilized to predict the chip formations,material removal behavior and cracks propagation under varying bone osteon cutting angles and depths.Series of orthogonal cutting experiments were conducted on cortical bone to investigate the impact of bone osteon cutting angle and depth of cut on cutting force,crack initialization and propagation.The observed chip morphology highly agreed with the prediction of chip formation based on the analytical model.The curly,serrated,grainy and powdery chips formed when the cutting angle was set as 0°,60°,90°,and 120°,respectively.Cortical bone were removed dominantly by shearing at a small depth of cut from 10 to 50μm,and by a mixture of pealing,shearing,fracture and crushing at a large depth of cut over 100μm at different bone osteon angles.Moreover,its fracture toughness was calculated based on measured cutting force.It is found that the fluctuation of cutting force is suppressed and the bone material becomes easy to remove,which attributes to lower fracture toughness at bone osteon cutting angle 0°.When the cutting direction develops a certain angle to bone osteon,the fracture toughness increases then the crack propagation is inhibited to some extent and the fluctuation of cutting force comparatively decreases.There is a theoretical and practical significance for tools design and operational parameters choice in surgeries.
基金Supported by National Science and Technology Major Project of China(No.2009ZX04012-021)Major State Basic Research Development Program of China ("973" Program, No.2009CB724306)
文摘This paper studies the influence of radial depth on vibration, chip formation and surface roughness during face milling of AISl3O4 austenitic stainless steel with indexable cemented carbide milling cutters. The amplitude of vibration acceleration increased with the increasing radial depth up to 80 mm. And the domain vibration frequency varied with the radial depth. In this paper, three types of chips were found： C shape, long shape and spiral shape. The minimum surface roughness value occurred when the radial depth equalled 40 mm in the experiment. Irregular changes of chip curl radius and chip thickness could be attributed to different numbers of alternately engaged teeth when the feed and speed were fixed. Surface roughness is related to forced vibration and chip formation. Radial depth with different numbers of alternately engaged teeth could significantly influence the forced vibration, chip formation, and surface roughness.
基金Supported by National Natural Science Foundation of China (Grant Nos.52005199 and 42241149)Shenzhen Fundamental Research Program (Grant Nos.JCYJ20200109150425085 and JCYJ20220818102601004)+2 种基金Shenzhen Science and Technology Program (Grant Nos.JSGG20201103100001004 and JSGG20220831105800001)Research Development Program of China (Grant No.2022YFB4602502)Knowledge Innovation Program of Wuhan-Basic Research (Grant No.2022010801010203)。
文摘To benefit tissue removal and postoperative rehabilitation,increased efficiency and accuracy and reduced operating force are strongly required in the osteotomy.A novel elliptical vibration cutting(EVC)has been introduced for bone cutting compared with conventional cutting(CC)in this paper.With the assistance of high-speed microscope imaging and the dynamometer,the material removals of cortical bone and their cutting forces from two cutting regimes were recorded and analysed comprehensively,which clearly demonstrated the chip morphology improvement and the average cutting force reduction in the EVC process.It also revealed that the elliptical vibration of the cutting tool could promote fracture propagation along the shear direction.These new findings will be of important theoretical and practical values to apply the innovative EVC process to the surgical procedures of the osteotomy.
文摘In this paper the nano-metric simulation of grinding of copper with diamond abrasive grains, using the molecular dynamics （MD） method, is considered. An MD model of nano-scale grinding, where a single diamond abrasive grain performs cutting of a copper workpiece, is presented. The Morse potential function is used to simulate the interactions between the atoms involved in the procedure. In the proposed model, the abrasive grain follows a curved path with decreasing depth of cut within the workpiece to simulate the actual material removal process. Three different initial depths of cut, namely 4 A, 8 A and 12 A, are tested, and the influence of the depth of cut on chip formation, cutting forces and workpiece tempera- tures are thoroughly investigated. The simulation results indicate that with the increase of the initial depth of cut, average cutting forces also increase and therefore the temperatures on the machined surface and within the workpiece increase as well. Furthermore, the effects of the different values of the simulation variables on the chip formation mechanism are studied and discussed. With the appropriate modifications, the proposed model can be used for the simulation of various nano-machining processes and operations, in which continuum mechanics cannot be applied or experimental techniques are subjected to limitations.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFB3206700)the Fundamental Research Funds for the Central Universities,China(Grant No.2023CDJYXTD-003)the Natural Science Foundation of Chongqing,China(Grant No.2022NSCQMSX2038).
文摘High-performance carbon fiber-reinforced polyether-ether-ketone(CF/PEEK)has been gradually applied in aerospace and automobile applications because of its high strength-to-weight ratio and impact resistance.The drymachining requirement tends to cause the cutting temperature to surpass the glass transition temperature(Tg),leading to poor surface quality,which is the bottleneck for dry milling of CF/PEEK.Temperature suppression has become an important breakthrough in the feasibility of high-speed dry(HSD)milling of CF/PEEK.However,heat partitioning and jet heat transfer mechanisms pose strong challenges for temperature suppression analytical modeling.To address this gap,an innovative temperature suppression analytical model based on heat partitioning and jet heat transfer mechanisms is first developed for suppressing workpiece temperature via the first-time implementation of an air jet cooling process in the HSD milling of UD-CF/PEEK.Then,verification experiments of the HSD milling of UD-CF/PEEK with four fiber orientations are performed for dry and air jet cooling conditions.The chip morphologies are characterized to reveal the formation mechanism and heat-carrying capacity of the chip.The milling force model can obtain the force coefficients and the total cutting heat.The workpiece temperature increase model is validated to elucidate the machined surface temperature evolution and heat partition characteristics.On this basis,an analytical model is verified to predict the workpiece temperature of air jet cooling HSD milled with UD-CF/PEEK with a prediction accuracy greater than 90%.Compared with those under dry conditions,the machined surface temperatures for the four fiber orientations decreased by 30%–50%and were suppressed within the Tg range under air jet cooling conditions,resulting in better surface quality.This work describes a feasible process for the HSD milling of CF/PEEK.
